PDF User Guides

Evaluation Board User Guide
UG-487
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
iCoupler EVAL-ADuM5010EBZ, 150 mW isoPower Evaluation Board
FEATURES
setting the desired output voltage, setting enable control, and
providing multiple positions for on-board loads and bypass
capacitors.
isoPower integrated, isolated dc-to-dc converter
Regulated 3.15 V to 5.25 V output
Up to 150 mW output power
20-lead SSOP package with 5.3 mm creepage
High temperature operation: 105°C
High common-mode transient immunity: >25 kV/µs
isoPower devices employ high frequency high power switching
circuits to enable power transfer across chip scale, air core
transformers. The evaluation board includes EMI mitigation
recommendations from the AN-0971 Application Note. With
the included techniques, this PCB and power module is capable
of meeting the requirements of CISPER22 Class A or Class B
depending on the voltage and load range.
SUPPORTED iCoupler® MODELS
ADuM5010
ADuM6010
GENERAL DESCRIPTION
The EVAL-ADuM5010EBZ supports the ADuM5010 and
ADuM6010 150 mW isolated power modules. It provides a
JEDEC standard SSOP20 pad layout as well as support for
Complete specifications for the ADuM5010 and ADuM6010
are provided in the ADuM5010 and ADuM6010 data sheets,
available from Analog Devices, Inc., and should be consulted
in conjunction with this user guide when using the evaluation
board.
11083-001
EVALUATION BOARD
Figure 1. EVAL-ADuM5010EBZ Evaluation Board
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 8
UG-487
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Bypass on the PCB ........................................................................3
Supported iCoupler® Models........................................................... 1
Provision for Loading ...................................................................3
General Description ......................................................................... 1
EMI Mitigation ..............................................................................4
Evaluation Board .............................................................................. 1
High Voltage Capability ...............................................................4
Revision History ............................................................................... 2
Evaluation Board Schematics and Artwork ...................................5
PCB Evaluation Goals .................................................................. 3
Ordering Information .......................................................................7
Connectors .................................................................................... 3
Bill of Materials ..............................................................................7
Part Configuration Structures .................................................... 3
REVISION HISTORY
11/12—Revision 0: Initial Version
Rev. 0 | Page 2 of 8
Evaluation Board User Guide
UG-487
Control of the VISO voltage is accomplished through a voltage
divider that’s center node is attached to the VSEL pin as shown
in Figure 3. There are two options for setting the output voltage
supported on this evaluation board. A 20 kΩ potentiometer is
installed at R1A in series with a 16.5 kΩ resistor at position
R16A making a variable resistance to VISO of 16.5 kΩ to 36 kΩ.
A resistor to ground at position R14A forms the lower leg of
the voltage divider. This will give a range of adjustment of
VISO < 3.3 V to > 5 V.
PCB EVALUATION GOALS
This board is intended to achieve two goals.


It will allow a user of the ADuM5010 or ADuM6010 to
exercise the functional capabilities of the part. These
include evaluation of bypass, loading, power supply
enable/disable control and setting the adjustable output
voltage level.
This evaluation board demonstrates the EMI mitigation
techniques required to make a low emissions design as
discussed in the AN-0971 Application Note.
CONNECTORS
This evaluation system will be used to evaluate a variety of
different aspects of performance. Connections to a power
supply and instrumentation are critical to performing accurate
measurements without creating artificial ringing, reflections,
ripple, and EMI.
Two types of interconnections are provided, SMA edge connectors and through-hole signal ground pairs. Between these
two options, both temporary and permanent connections to
the board are easily made. When coax connections are desired,
SMA connectors are available for the VDDP power input and
VISO output. These connectors were chosen because they are
low profile and provide excellent mechanical connections to
the PCB. Most lab equipment is geared toward use of BNC
connectors, so adaptors will be required to use the on board
connectors.
Power can be directly wired to the PCB via the P6A and P7A
through-hole connectors. These provide a power ground
pair with the power on the Pin 1 hole. These through holes
are on 200mil centers, which match the pin spacing required
for Tektronix active probes. These positions can be used for
scope test points or direct wiring of power and ground.
Alternatively, if a fixed output voltage is desired, R16A can be
removed and a resistor can be installed in R13A that combined
with the existing resistance in R14A will form a fixed voltage
divider to set VISO to a single voltage. Refer to the ADuM5010
or ADuM6010 data sheet for selection of resistor values.
BYPASS ON THE PCB
Several positions and structures are provided to allow optimum
bypass of the evaluation board. Provisions have been made for
optional surface-mount bulk capacitors to be installed near the
power connectors to compensate for long cables to the power
supply or external load. Parallel bypass capacitors are installed
near the ADuM5010 or ADuM6010 consisting of a 0.1 μF and a
10 μF capacitor for VDDP and VISO. The 0.1 μF capacitors can be
moved to positions on the back side of the board if required.
The PCB also implements distributed capacitive bypass on the
primary side of the PCB. This consists of power and ground fills
on the top and bottom layers of the PCB on the VDDP side of the
board. This is one of the techniques discussed in the EMI
Mitigation section. It has the added benefit of providing added
bypass on the primary side of the converter where the largest
currents flow as well as RF shielding.
PROVISION FOR LOADING
VISO can be loaded three ways.
PART CONFIGURATION STRUCTURES
The ADuM5010 and ADuM6010 have pins that must have
set inputs for the IC to operate properly. The evaluation board
allows all a full range of configuration options. On the primary
side, the PDIS pin must either be tied low to enable the converter, or pulled high to disable the output power and put the
part in a standby state. Connector P3A allows a jumper to be
placed between Pin 1 and Pin 2 to disable the converter, or
between Pin 2and Pin 3 to enable the converter. The header
can be removed if an external logic source controls the disable
function and the signal can be fed directly into Position 2 of
the header.



Rev. 0 | Page 3 of 8
An external load can be connected via the SMA connector.
A fixed resistor can be installed at R18A.
A surface mount resistor can be installed at R15A.
UG-487
Evaluation Board User Guide
EMI MITIGATION
The PCB implements EMI mitigation techniques discussed
in the AN-0971 Application Note to demonstrate the
recommended board layout options for this device. These
techniques include stitching capacitance and edge guarding.
Stitching Capacitance
The capacitance between the primary and secondary power
and ground planes is the most effective way to reduce high
frequency emissions from an isoPower device. Figure 2
shows how the inner layers of a PCB can create this stitching
capacitance by overlapping inner layer metal to create an
extremely low inductance capacitance. The green area shows
the active coupling area.
Edge Guarding
Providing guard rings laced together with vias on each layer
of the primary side reduces edge emissions from the PCB
stack-up. This addresses emissions due to large high frequency
vertical current flow through vias and traces near the edges.
Figure 4 shows the top layer guard ring and the bottom layer
ground fill as well as the regularly spaced vias in the guard ring
that creates a cage type structure to reflect inter-plane emissions
back into the PCB. Figure 5 shows the top layer power fill along
with its vias to the Layer 3 power plane. This top layer power
fill adds distributed capacitance as well as shielding for the
layer below.
HIGH VOLTAGE CAPABILITY
This PCB is designed in line with 2500 V basic insulation
practices. High voltage testing beyond 2500 V is not recommended. Appropriate care must be taken when using this
evaluation board at high voltages, and it should not be relied
on for safety functions since it has not been hi-pot tested or
certified for safety.
LAYER 2 GROUND
LAYER 3 POWER
11083-003
OVERLAP
CREATING CAPACITANCE
Figure 2. Ground and Power Planes Creating Stitching Capacitance
Rev. 0 | Page 4 of 8
Evaluation Board User Guide
UG-487
EVALUATION BOARD SCHEMATICS AND ARTWORK
MTSW-202-12-G-S-730
MTSW-202-12-G-S-730
VDDPA
P6A
1
2
VISOA
VDDPA
P7A
1
2
VISOA
P
C8A
DNI
N
P
C10A
DNI
N
JOHNSON142-0701-851
J4A
JOHNSON142-0701-851
VDDPA
C12A
C3A
C5A
0.1µF
1
2
3
4
5
6
7
8
9
10
VDDPA
VDDPA
C4A
10µF
R15A
R18A
5 4 3 2
DNI
DUT1A
ADuM5010ARSZ
MOLEX22-03-2031
P3A
1
2
3
C14A
0.1µF
1
C6A
0.1µF
VDD1
GNDP
NC
NC
GNDP
GNDP
NC
PDIS
VDDP
GNDP
VDD2
GNDISO
NC
NC
GNDISO
GNDISO
NC
VSEL
VISO
GNDISO
20
19
18
17
16
15
14
13
12
11
VISOA
R13A
TBD0805
R16A
16.5kΩ
3
R14A
10kΩ
2
R1A
20kΩ
1
VDDPA
VISOA
VISOA
C7A
C11A
C13A
0.1µF
C15A
10µF
11083-002
2 3 4 5
VISOA
CW
J1A
1
VISOA
Figure 3. ADuM5010/ADuM6010 Schematic
Rev. 0 | Page 5 of 8
Evaluation Board User Guide
11083-004
UG-487
11083-005
Figure 4. Edge Guard on Primary Side Top and Bottom Layers
Figure 5. Power Fill, Top Layer, Primary Side
Rev. 0 | Page 6 of 8
Evaluation Board User Guide
UG-487
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Quantity
1
4
2
1
1
1
2
Reference Designator
DUT1A
C5A, C6A, C16A, C17A
C4A, C15A
R14A
R16A
R1A
J1A, J4A
Description
ADuM5010
0.1 µF, 25 V, 10%, 0805
10 µF, 6.3 V, 10%, 0805
10 kΩ, 1/10 W, 1% 0805
16.5 kΩ, 1/10 W, 1%, 0805
20 kΩ resistor VAR 3/8 inch SQ top ADJ
SMA edge connector, Johnson 142-0701-851
Rev. 0 | Page 7 of 8
UG-487
Evaluation Board User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG11083-0-11/12(0)
Rev. 0 | Page 8 of 8