SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Su pe rs ed ed Demo Guide August 2014 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Revision History Date Revision Change 18 August 2014 4 Fifth release 3 May 2014 3 Fourth release 16 December 2013 2 Third release 27 November 2013 1 Second release 09 October 2013 0 First release Confidentiality Status Su pe rs ed ed This is a non-confidential document. SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Table of Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Microsemi Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 In-System Programming Using USB OTG Controller Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ed ed Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Requirements and Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Demo Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Demo Design Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Demo Design Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Setting Up the Demo Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Alternate Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Board Setup Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Running the Demo Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Authenticate Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Verify Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 17 19 21 rs Checking if the Fabric is Programmed Successfully . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Checking if the eNVM is Programmed Successfully . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Programming Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 pe Appendix 1: Connecting the SmartFusion2 Device to the Host PC Through the USB to UART (FTDI) Interface . Appendix 2: Board Setup when using the USB-RS232 Serial Adapter or RS232 Cable . . . . . . . . . . . . . . . . . . . . Appendix 3: Board Setup Through the USB to UART (FTDI) Interface using the USB A to Mini - B Cable . . . . . Appendix 4: Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 5: Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 6: Generating .spi Programming File using Libero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix 7: Hardware Project Implementation Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 25 26 27 28 29 31 Su Configuring the I/Os for Flash*Freeze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Standby Clock Source Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 SoftConsole Project Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 A List of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 B Product Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Technical Support Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contacting the Customer Technical Support Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 36 36 36 36 Email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 My Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Outside the U.S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 ITAR Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Revision 4 3 Preface About this document This demo is for SmartFusion®2 system-on-chip (SoC) field programmable gate array (FPGA) devices. It provides instructions on how to use the corresponding reference design. Intended Audience • FPGA designers • Embedded designers • System-level designers References ed ed SmartFusion2 devices are used by: Microsemi Publications SmartFusion2 Programming User Guide • SmartFusion2 System Controller User Guide • SmartFusion2 Microcontroller Subsystem User Guide • SmartFusion2 SoC FPGA Remapping eNVM, eSRAM, and DDR/SDR SDRAM Memories Application Notes • Configuring Serial Terminal Emulation Programs Tutorial rs • Su pe See the following web page for a complete and up-to-date listing of SmartFusion2 device documentation: http://www.microsemi.com/products/fpga-soc/soc-fpga/smartfusion2#documents. Revision 4 4 In-System Programming Using USB OTG Controller Interface Introduction You can use in-system programming (ISP) to reprogram for design iterations and field upgrades. SmartFusion2 devices support ISP using universal serial bus (USB) on-the-go (OTG) controller interface. This document describes how to program the following using ISP through the USB OTG controller interface: Embedded nonvolatile memory (eNVM) • FPGA fabric • Both the eNVM and the FPGA fabric ed ed • For information on different programming modes supported by SmartFusion2 SoC FPGAs, refer to the SmartFusion2 Programming User Guide. For information on USB OTG controller, refer to the SmartFusion2 Microcontroller Subsystem User Guide. Requirements and Details Table 1 • Reference Design Requirements and Details Hardware Requirements SmartFusion2 Development Kit • 12 V adapter • FlashPro4 programmer USB A to Mini-B cable • USB cable with Micro-A end Rev D or later pe • Description rs Reference Design Requirements and Details USB-RS232 Serial adapter or RS232 cable - Host PC or Laptop Windows 64-bit Operating System Software Requirements v11.4 FlashPro Programming Software v11.4 Host PC Drivers USB to UART drivers Su Libero® System-on-Chip (SoC) for viewing the design files Revision 4 5 In-System Programming Using USB OTG Controller Interface Demo Design Introduction The demo design files are available for download from the following path in the Microsemi® website: http://soc.microsemi.com/download/rsc/?f=sf2_isp_using_usb_interface_demo_11p4_df The demo design files include: • Sample programming files • Libero SoC project • STAPL programming file • readme.txt GRZQORDGBIROGHU! ed ed Figure 1 shows the top level structure of the design files. For further details, refer to the readme.txt file. VIBLVSBXVLQJBXVEBLQWHUIDFHBGHPRBGI VDPSOHBSURJUDPPLQJBILOHV OLEHUR VWDSOBSURJUDPPLQJBILOH Figure 1 • rs UHDGPHW[W Demo Design Files Top Level Structure Figure 2 describes the demo. The SmartFusion2 device application configures the following: The MMUART_1 peripheral for serial communication with host PC. • The USB OTG as mass storage class host, which can read or write files from the mass storage device connected to the SmartFusion2 device through USB cable with Micro A end. Refer to the "Appendix 7: Hardware Project Implementation Settings" section on page 31. pe • Su The SmartFusion2 device also initializes the system controller to run the ISP service. The SmartFusion2 device detects the connected USB mass storage device and accesses the programming files. The Cortex-M3 processor reads 512 byte blocks of the programming file data from the USB mass storage device and sends the received blocks of data to the system controller ISP service. The system controller ISP service executes the ISP operation in the requested mode and reports the status to the Cortex-M3 6 R e vi s i o n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide processor. Refer to the "Demo Design Description" section on page 8 for information on the various modes of operation. Cortex-M3 System Controller MSS COMM_ BLK COMM_ BLK Cache Controller USB Mass Storage Device USB OTG APB_1 SII Master UJTAG AHB Bus Matrix eNVM_0 FPGA Fabric eNVM_1 APB_1 Top Level Demo Diagram Host PC Data Transfer from USB Mass Storage Device Programming eNVM and/or Fabric using System Controller ISP Service SmartFusion2 Figure 2 • MMUART_1 ed ed USI AHB SII Master There are two ways to connect the host PC to the SmartFusion2 device: • Using the USB-RS232 Serial adapter or the RS232 cable. • Using the USB to UART (FTDI) interface. Refer to the "Appendix 1: Connecting the SmartFusion2 Device to the Host PC Through the USB to UART (FTDI) Interface" on page 24. Su pe – Refer to the "Running the Demo Design" section on page 12. rs – Revision 4 7 In-System Programming Using USB OTG Controller Interface Demo Design Features This demo design performs three types of programming based on the input provided by the programming file. • eNVM programming: The ISP programming service programs only eNVM. In this case the input programming file has only eNVM content. • FPGA fabric programming: The ISP programming service programs only the FPGA fabric. In this case the input programming file has only the FPGA fabric content. • eNVM and FPGA fabric programming: The ISP programming service programs both the FPGA fabric and eNVM. In this case the input programming file has both the FPGA fabric and eNVM content. ed ed Demo Design Description The ISP in SmartFusion2 devices is performed by the Cortex-M3 processor and the system controller. The system controller manages the SmartFusion2 device programming and handles the system service requests. The SmartFusion2 device allows the Cortex-M3 processor to directly provide a bitstream to the system controller for programming. The Cortex-M3 processor initializes the system controller and receives the programming bitstream from the USB mass storage device through the USB OTG controller interface. The received bitstream is sent to the system controller to execute the ISP service in one of the following modes of operation: Authenticate: System controller ISP service validates the integrity of the input data bitstream and reports the status information to the Cortex-M3 processor. – Program: System controller ISP service programs the following depending on the input data bitstream: – eNVM – FPGA fabric – Both the eNVM and the FPGA fabric pe • For security and reliability reasons, Microsemi recommends that the bitstream is authenticated before the program is executed using Authenticate Operation mode. The SmartFusion2 device application must commit only the bitstream for programming after successful authentication and the integrity of the bitstream is validated. rs • • Verify: System controller ISP service verifies the contents of the SmartFusion2 device against the input data bitstream and reports the status information to the Cortex-M3 processor. The system controller ISP service utilizes the COMM_BLK interface to receive the entire programming data bitstream as a continuous stream of bytes. Refer to the SmartFusion2 Microcontroller Subsystem User Guide for more information on communication block (COMM_BLK). Su The Cortex-M3 processor in the SmartFusion2 device can execute an application image from embedded SRAM (eSRAM), eNVM or DDR/SDR memories. Refer to the SmartFusion2 SoC FPGA Remapping eNVM, eSRAM, and DDR/SDR SDRAM Memories Application Notes for more information on remapping techniques. In this demo design, the Cortex-M3 processor executes the ISP application image from eSRAM while the eNVM programming taking place, that is during Program operation mode. In order to execute the application image from eSRAM, the Cortex-M3 processor copies the ISP application image (resides in eNVM data client) to the eSRAM and remaps the eSRAM to the Cortex-M3 processor code region. For Verify and Authenticate operation modes, the application image can be executed from either eNVM or eSRAM since the eNVM programming is not taking place. Refer to the "Appendix 7: Hardware Project Implementation Settings" section on page 31. Programming Files Sample programming files with the file extension .spi are provided to program: 8 • eNVM • FPGA Fabric • Both the eNVM and the FPGA fabric R e vi s i o n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide The folder <download_folder>\sf2_isp_using_usb_interface_demo_df\sample_programming_files contains the following sample programming files along with Libero design files. • envmonly.spi: Programs only eNVM. The eNVM client has a simple message display program. • fabriconly.spi: Programs only the FPGA fabric. The FPGA fabric has a light-emitting diode (LED) blinking logic. • fabenvm.spi: Programs both the FPGA fabric and eNVM. The eNVM client has a message display program and the FPGA fabric has an LED blinking logic. The folder <download_folder>\sf2_isp_using_usb_interface_demo_df\sample_programming_files\fabric_an d_envm contains the Libero design to generate this sample programming file. • isp_demo.spi: This is the .spi file format version of isp_demo.stp file provided in <download_folder>\sf2_isp_using_usb_interface_demo_df\stapl_programming_file. ISP Execution Flow ed ed Note: For more information on generating .spi programming files refer to the "Appendix 6: Generating .spi Programming File using Libero" on page 29. Figure 3 on page 10 describes the ISP flow. The SmartFusion2 Device application initially configures the USB OTG controller in Host mode and MMUART_1 for serial communication. It also initializes the system controller to start the ISP service in the selected operation mode. Su pe rs On receiving the ISP operation mode and the programming file index, the application starts reading the input source programming file in a 512 byte blocks. The application stores the received data in a temporary buffer and sends the same data to the ISP service. The application requests the next block of 512 byte data until the entire file gets transferred from the USB mass storage device. The SmartFusion2 Device application is notified with a status code when the ISP service completes the authentication or the verification process. When the operation mode is Program, an internal device reset is generated for the new design to take effect. Revision 4 9 In-System Programming Using USB OTG Controller Interface Figure 3 shows the ISP execution flow. 6WDUW6PDUW)XVLRQ'HYLFH $SSOLFDWLRQ ,QLWLDOL]HWKH8$57 ,QLWLDOL]HWKHV\VWHPFRQWUROOHU &RQILJXUHWKH86%27*LQKRVWPRGH ed ed $FFHVVWKH86%PDVVVWRUDJHGHYLFH *HWWKH,63RSHUDWLRQPRGH 'LVSOD\DYDLODEOHILOHV *HWWKHSURJUDPPLQJILOH,QGH[ $XWKHQWLFDWH 3URJUDP :KLFK,63 2SHUDWLRQ PRGH" 9HULI\ rs 6WDUWWKH,63VHUYLFHZLWK 3URJUDPRSHUDWLRQPRGH 6WDUWWKH,63VHUYLFHZLWK 9HULI\RSHUDWLRQPRGH pe 6WDUWWKH,63VHUYLFHZLWK $XWKHQWLFDWHRSHUDWLRQPRGH 5HDGELWVWUHDPIURPWKH 86%0DVVVWRUDJHGHYLFH WRLQSXWWKH,63VHUYLFH 5HDGELWVWUHDPIURPWKH 86%0DVVVWRUDJHGHYLFH WRLQSXWWKH,63VHUYLFH VSLILOH WUDQVIHUUHG FRPSOHWHO\" Su 1R 1R <HV 6WDUWQHZGHVLJQ DSSOLFDWLRQ <HV 1HZGHVLJQ H[HFXWLRQ 6WRS 3UHVVDQ\NH\WRFRQWLQXH 10 ,QWHUQDOGHYLFHUHVHW IRUQHZGHVLJQWR WDNHHIIHFW 5HSRUWWKHFRPSOHWLRQRIWKH RSHUDWLRQZLWKVWDWXVFRGHWR 6HULDOWHUPLQDOHPXODWLRQSURJUDP Figure 3 • VSLILOH WUDQVIHUUHG FRPSOHWHO\" Execution Flow of ISP Operation Mode R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Setting Up the Demo Design 1. Connect the FlashPro4 programmer to the J59 connector of the SmartFusion2 Development Kit board. 2. Connect the host PC to the DB9-RS232 connector provided on the SmartFusion2 Development Kit board using the USB-RS232 serial adapter cable or the RS232 cable. Su pe rs ed ed When using USB-RS232 serial adapter cable, make sure that the USB-RS232 serial adapter drivers are automatically detected. Figure 4 shows an example Device Manager window that has the USB-to-Serial Comm Port listed under Ports (Comm & LPT). COM port number is required to run the demo design, so make a note of it. Figure 4 • USB-to-Serial Communication Port Revision 4 11 In-System Programming Using USB OTG Controller Interface 3. Connect the jumpers on the SmartFusion2 Development Kit board, as described in Table 2. For information on jumper locations, refer to the "Appendix 4: Jumper Locations" on page 27. – Caution: Before making the jumper connections, switch off the power supply switch, SW7. Table 2 • SmartFusion2 Development Kit Jumper Settings Jumper Number Settings Notes J70, J93, J94, J117, J123, J142, J157, J160, J167, J225, J226, J227 1-2 closed These are the default jumper settings of the Development Kit board. Make sure these jumpers are set accordingly. J2 1-3 closed 2-3 closed J139 1-2 closed Jumper to select USB reset. J163 1-2 closed Jumper to select USB OTG mode of operation. J164 1-2 closed Jumper to provide the VBUS supply to USB when using in Host mode. J188, 197 1-2 closed • Jumper settings when using MMUART_1. These are not set by default and must be set manually. • Change these jumper settings if the USB to UART (FTDI) interface is used. Refer to "Appendix 3: Board Setup Through the USB to UART (FTDI) Interface using the USB A to Mini - B Cable". ed ed J23 4. Connect the power supply to the J18 DC jack. rs Alternate Setup pe This demo can also be run using the USB to UART (FTDI) interface without using the USB-RS232 serial adapter or the RS232 cable. Refer to "Appendix 1: Connecting the SmartFusion2 Device to the Host PC Through the USB to UART (FTDI) Interface" on page 24 for information on how to connect the host PC to the SmartFusion2 Development Kit board for serial communication through the FTDI USB interface using the USB A to Mini - B cable. Board Setup Snapshot Snapshots of the SmartFusion2 Development Kit board with all the setup made in both types of connections are given in the following appendices: "Appendix 2: Board Setup when using the USB-RS232 Serial Adapter or RS232 Cable" on page 25 Su • • "Appendix 3: Board Setup Through the USB to UART (FTDI) Interface using the USB A to Mini - B Cable" on page 26 Running the Demo Design 1. Download the demo design from: http://soc.microsemi.com/download/rsc/?f=sf2_isp_using_usb_interface_demo_11p4_df. 2. Switch ON the SW7 power supply switch. 3. Start any serial terminal emulation program such as: 12 – HyperTerminal – PuTTY – Tera Term R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide The configuration for the program is: – Baud Rate: 57600 – 8 Data bits – 1 Stop bit – No Parity – No Flow Control For information on configuring the serial terminal emulation programs, refer to the Configuring Serial Terminal Emulation Programs Tutorial. 4. Connect the USB cable Micro A end to the P1 connector of SmartFusion2 Development Kit board and other end to the USB mass storage device. The USB OTG controller in Host mode is tested to work with mass storage devices listed below: Sandisc CruzeerBlade - 16Gb/8Gb/4Gb/1GB – Kingston Datatraveller - 4Gb/2Gb – Kingston DT109B - 8GB – Transcend JetFlash - 4Gb ed ed – Make sure to connect preformatted USB Flash drive to the SmartFusion2 device with the sample programming files provided in <download_folder>\sf2_isp_using_usb_interface_demo_df\sample_programming_files. 5. Launch the FlashPro software. 6. Click New Project. Su pe rs 7. In the New Project window, type the project name. Figure 5 • FlashPro New Project 8. Click Browse and navigate to the location where you want to save the project. 9. Select Single device as the Programming mode. 10. Click OK to save the project. 11. Click Configure Device on the FlashPro GUI. Revision 4 13 In-System Programming Using USB OTG Controller Interface FlashPro Project Configured Su Figure 6 • pe rs ed ed 12. Click Browse and navigate to the location where the isp_demo.stp file is located and select the file. The default location is: <download_folder>\sf2_isp_using_usb_interface_demo_df\stapl_programming_file. The required programming file is selected and is ready to be programmed in the device. 14 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Figure 7 • pe rs ed ed 13. Click PROGRAM to start programming the device. Wait until you get a message indicating that the program passed. ISP requires the SmartFusion2 device to be preprogrammed with the application code to activate the ISP service. So, the SmartFusion2 device is preprogrammed with the isp_demo.stp using FlashPro software. FlashPro Program Passed – LEDs 5 to 8 blinking in the board indicates that the SmartFusion2 device fabric is preprogrammed successfully. Su On programming the SmartFusion2 device successfully using FlashPro, the serial terminal emulation program shows the initialization messages and ISP operation modes as shown in Figure 8 on page 16. Revision 4 15 pe ISP Operation Modes Selection Su Figure 8 • rs ed ed In-System Programming Using USB OTG Controller Interface 16 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide 14. On selecting the operation mode, the files in the USB storage device are displayed as shown in Figure 9. Figure 9 • pe rs ed ed Note: Maximum of 10 files can be shown from the USB storage device. Available Files in USB Mass Storage Device Su 15. Select the programming file from the listed files by its index to perform the selected ISP operation mode. Authenticate Operation Mode To authenticate the data from fabenvm.spi, enter: 1. 0 to select Authenticate operation mode under Select ISP operation mode. 2. The corresponding index number to select fabenvm.spi programming file. Revision 4 17 In-System Programming Using USB OTG Controller Interface Su pe rs ed ed On selecting the programming file, the application starts reading the programming file from USB mass storage device to execute the ISP operation mode. On completion of the ISP authentication, the serial terminal emulation program displays an operation success message. Figure 10 shows the operation success message. Figure 10 • ISP Authentication Results 3. Press SW9 to reset the SmartFusion2 Development Kit or Power Cycle the SmartFusion2 Development Kit to try other ISP operation modes. If the USB storage device files are not displayed on serial terminal emulation program, press SW9 to reset the board. 18 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Verify Operation Mode To verify the device FPGA fabric and eNVM contents, enter: 1. 2 to select Verify operation mode under Select ISP operation mode. 2. The corresponding index number to select isp_demo.spi programming file. Su pe rs ed ed On selecting the programming file, the application starts reading the programming file from USB mass storage device to execute the ISP operation mode. On completion of the ISP verification, the serial terminal emulation program displays an operation success message. Figure 10 shows the operation success message. Figure 11 • ISP Verification Results The verification operation demonstrated is for the isp_demo.stp file that is already running in the SmartFusion2 device. If any other .spi file is verified while the isp_demo.stp file is still running, that verification operation fails. Revision 4 19 In-System Programming Using USB OTG Controller Interface If the verification fails, the serial terminal emulation program displays an error message with an error code. Figure 12 shows an example error message. For more information on error codes, refer to the "Appendix 5: Error Codes" on page 28. The programming files are at: <download_folder>\sf2_isp_using_usb_interface_demo_df\sample_programming_files. Su pe rs ed ed All of them do not pass the verification. Only the isp_demo.spi file passes the verification operation as it matches with the SmartFusion2 device contents (isp_demo.stp). The other programming files fail verification. Figure 12 • ISP Verification Failure Error Message 3. Press SW9 to reset the SmartFusion2 Development Kit or Power Cycle the SmartFusion2 Development Kit to try other ISP operation modes. If the USB storage device files are not displayed on the serial terminal emulation program, press SW9 to reset the board. 20 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Program Operation Mode To program the FPGA fabric and the eNVM of the SmartFusion2 device using the fabenvm.spi file, enter: 1. 1 to select Program operation mode under Select ISP operation mode. 2. The corresponding index number to select fabenvm.spi programming file. On selecting the programming file, the application starts reading the programming file from the USB mass storage device to execute the ISP operation mode. The application checks the data integrity of the selected programming file prior to perform the ISP program operation. Once the programming operation is completed, an internal reset is generated for the new design to take effect. Su pe rs ed ed Figure 13 shows selection of program operation mode for the fabenvm.spi programming file. Figure 13 • ISP Program Operation Mode Revision 4 21 In-System Programming Using USB OTG Controller Interface Press SW9 to reset the SmartFusion2 Development Kit or Power Cycle the SmartFusion2 Development Kit. Checking if the Fabric is Programmed Successfully LEDs 1 to 4 blinking in the board indicates that the fabric is programmed successfully. Checking if the eNVM is Programmed Successfully Su pe rs ed ed The serial terminal emulation program displays the success message as shown in Figure 14 if the eNVM is programmed successfully. Figure 14 • ISP Program Results 22 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Programming Results The result shown in Figure 14 on page 22 is for the fabenvm.spi file. Table 3 shows the possible results for ISP Program operation mode for sample programming files provided in folder <download_folder>\sf2_isp_using_usb_interface_demo_df\sample_programming_files. Not all.spi files listed in the table are demonstrated. Table 3 • ISP Programming Results *.spi Programming File Name eNVM Programming Result FPGA Fabric Programming Result envmonly.spi The serial terminal emulation program shows successful NA eNVM program message fabonly.spi NA fabenvm.spi The serial terminal emulation program shows successful SmartFusion2 LEDs 1 to 4 blinks eNVM program message ed ed SmartFusion2 LEDs 1 to 4 blinks Su pe rs After successful ISP Program operation, the SmartFusion2 Development Kit board must be reprogrammed with the original isp_demo.stp file to try the ISP operation modes again. Revision 4 23 In-System Programming Using USB OTG Controller Interface Appendix 1: Connecting the SmartFusion2 Device to the Host PC Through the USB to UART (FTDI) Interface The following procedure describes how to connect the SmartFusion2 device to the host PC through the USB to UART (FTDI) interface using a USB A to Mini-B Cable for serial communication: 1. Connect the host PC to the J24 connector using the USB A to Mini-B cable. Su pe rs ed ed 2. Make sure that the USB to UART bridge drivers are automatically detected. Of the four COM ports, select the one with Location as on USD Serial Converter D. Figure 15 shows an example Device Manager window that has the USB Serial Port and its properties showing the port number and location. COM port number is required to run the demo design, so make a note of it. Figure 15 • Device Manager window Showing the USB Serial Port 3. Connect the jumpers as follows: 24 – Pin 2 of J197 to pin 3 of J129 – Pin 2 of J188 to pin 3 of J133 – Figure 17 on page 26 shows these pin connections. – Refer to Figure 18 on page 27 for the location of the jumpers. These connections are required for connecting the MMUART_1 TXD and RXD signals to the FTDI USB to UART bridge available in the SmartFusion2 Development Kit board. R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Appendix 2: Board Setup when using the USB-RS232 Serial Adapter or RS232 Cable Power supply switch SW7 ed ed DC Jack to connect 12 V adapter USB Mass Storage device USB-RS232 serial adapter pe DB9-RS232 connector rs USB cable with Micro A end FlashPro4 Connector LED 1 to LED 8 SW9 to reset Su Figure 16 • Board Setup when using the USB-RS232 Serial Adapter or RS232 Cable Revision 4 25 In-System Programming Using USB OTG Controller Interface Appendix 3: Board Setup Through the USB to UART (FTDI) Interface using the USB A to Mini - B Cable ed ed Power supply switch SW7 DC Jack to connect 12 V adapter USB Mini - B Connector Pin 2 of J197 to Pin 3 of J129 Pin 2 of J188 to Pin 3 of J133 USB Mass Storage device rs USB cable with Micro A end pe FlashPro4 Connector LED 1 to LED 8 SW9 to reset Su Figure 17 • Board Setup when Through the USB to UART (FTDI) Interface using the USB A to Mini - B Cable 26 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide B11 B14 R26 C7 R27 R25 R24 R23 R36 R56 DS11 PGOOD R52 R35 C42 6 AT FLAG DS10 R55 C44 C58 R130 SC2 D11 C71 R131 U20 J44 SC1 U15 R104 C61 C68 SC3 SC4 R123 J31 L5 4 ON OFF D5 D6 3 1 R22 R21 C6 CONN1 R80 R113 R81 R114 DS16 P1LED3 DS17 P1LED2 R82 DS18 P1LED1 DS19 P1LED0 R83 DS12 P0LED3 DS13 P0LED2 DS14 P0LED1 DS15 P0LED0 POE PWR ENB HPOUTCLK5 C32 C33 R50 R100 R111 R112 R150 R151 R152 R157R153 R154 C78 C79 R158R155 R137 C74 1 DS22 J103 U33 C84 GND T2 J112 1 R170 Q18 DS25 J116 1 J132 R189 C105 U37 GND C111 L10 A B C D E F G H J TXN0 RXP0 RXN0 TXP2 TXN2 TXP1 TXN1 RXN1 RXP1 TXP3 TXN3 C119 C120 C121 TXP0 C134 J150 J148 J149 J171 R244 1P0V_PHY J186 J182 J192 J191 RXN2 RXP2 RXN3 RXP3 D14 J189 TS_MDIO TP25 J190 R238 R239 R240 R241 J185 TS_MDC J169 J168 R243 R242 1 R247 J170 R219 J156 J166 1 C152 C153 R278 R279 J147 J151 C128 C129 C130 C131 L13 U45 R220 R221 1 R670 R230 J177 1 R377 R378 R379 R380 R381 R382 R383 Q20 Q21 Q22 Q23 Q24 Q25 Q26 Q27 1 J229 1 DDR3_1P5V TP21 R354 R355 D18 R365 C204 R366 D20 TP20 R346 D17 D16 R339 R338 U61 TP12 U59 C200 C202 DVDD12 R375 D15 GND R325 C186 R350 TP24 C198 J220 J219 J228 J207 J206 2P5V_LDO U60 R353 LED8 LED7 R374 R364 LED6 R373 R363 LED5 R372 R362 LED4 R371 R361 LED3 R370 R360 LED2 R369 R359 R326 C191 R356 C189 SERDES1 REFCLK0_N J208 GND SF2 DEV KIT LED1 R368 R358 R132 R143 J205 R312 3P3V_LDO C70 Q15 GND TP14 J211 DDR3_VTT R367 R357 1 T1 J80 R182 R183 789 123 1 J160 RS6 1 J167 C150 C151 R276 R277 R102 R103 J16 R30 J15 R32 R46 J67 R178 R179 R184 R185 C94 C95 1 J142 R203 R204 R206 R207 R212 R217 C148 C149 R274 R275 C164 TP22 U56 J152 R256 R376 R385 1 1P0V_PHY C67 1 J82 U36 R662 Y2 C85 C86 C87 C88 C89 C90 R205 C146 R2 C147 66 R226 R229 R231 R232 R234 R235 R236 R237 R267 R269 R280 C63 D10 Q14 ON 1 R218 R281 TP29 GND_0 C54 J153 R213 R215 R268 POE CONN J10 J11 TP10 C28 C29 R45 C76 C75 C73 C72 C69 C62 C60 C59 SW8 2 4 R149 R159 R160 J81 3 1 R172 R173 C91 C92 R2 86 R282 R283 C159 R270 R97 TP13 DVP-102-000400-001 REFCLK0_P Rev% U55 J227 C173 1 1 L12 U51 C167 789 A B C D E F G H J K L M N PLLXVDDA U54 C184 J230 R47 R48 R49 1 1 C66 1 3 J54 R146 U23 4 2 SW9 RS2 C98 J117 C100 C96 C103 C104 3 J224 C203 U40 U42 123 789 A B DC E F G H J K L M N J128 ON SW10 A1 R86 C51 C77 R671 R181 R186 R188 J126 J127 J125 RS4 VPP 2 C197 2 1 B1 R148 LED9 RST LED J70 U27 rs R663 JTAG SEL U31 U30 3 J233 1 123 789 J226 R329 C188 R340 C192 J223 R341 R342 1 R99 C49R87 R88 J33 C50R89 R90 R106 R107 R108 R109 R110 R95 C52 R91 C53 R92 R93 R94 J29 J19 J26 GND J37 1 J55 1 J59 U25 3 R384 C199 R351 R344 R345 C195 1 R180 J124 RS3 RS5 C37 R74 C48 GND R166 R167 R168 Y3 C162 123 R311 R319 R320 R317 R318 C177 C178 C182 C183 C185 R327 1 R335 R336 C190 R337 U58 J222 R343 C196 R348 R349 R352 C201 J203 J234 J215 R290 R291 C187 J217 R295 J130 R187 R332 R296 R333R334 1 R299 R302 R303 R304 TP7 R305 R306 R307 R308 R309 GND R177 L8 J123 C114 A30 PLLMDDRVDDA U53 J212 C181 R321 1 R322R314 R323 U57 R328 R331 R330 C193C194 J216 R289 C169C166 U50 R293 R300R294 U52 J204 C180 C176 C175 R315 J218 1 1 J172 K23 J175 L26 J179 H26 J184 J29 J188 H30 J195 H28 J197 G29 J200 F30 J202 K25 BA J210 DC L23 E F J214 G N23 HJ K L M N J225 C160 R288 R287 3 J193 L15 C171 1 C174 AK1 3 C172 C158 U48 1 1 L7 PCIEXVDD AK30 R310 J173 J180 1 3 J14 J12 SW1 R39 R53 R54 R60 R61 U8 U12 J38 Q19 R271 C155 R272 R249 R273 C142 R227 R258 R233 C165 R313 R316 C179 R324 GND DB9-RS232 1 ANALOG INPUT PLLFDDRVDDA R674 R673 R672 R676 J139 P24 J141 N26 J144 M27 J146 L29 J155 L28 J159 K30 J162 J27 Su C143 R248 R255 C144 R264 C161 C163 1 HDR-RS485 R347 20 8 C97 C101 C102 C38 C40 C43 R78 C46 7 7 U62 C93 C99 GND_C 1 2 J43 1 R163 U29 1 3 3 R175 R176 pe 1 1 C125 R202 R192 D12 1 C112 J157 TP28 R261 C139 R262 R245 C154 R263 L14 R246 C140 HVDD R252 R253 R254 R257 1 1 V2J21 M2 J20 M2J20 H2 J19G3 J196 H2J19 J2 J18 J3 J18 J2 J17 K2 J174 9 4 8 7 0 3 6 8 4 63 4 9 5 1 7 9 0 C123 C124 C127 TP27 U47 C137 1 J176 C145 R259 R260R250 3 1 J138 P23 J140 N25 J143 N24 J145 M26 J154 L30 J158 K29 C133 J161 K28 1 J165 J137 D13 J181 C156 C157 1 TP26 VDDIO R292 C168 R298 R297 C170 R301 19 J221 TP3 1 3 2 1 50 MHZ R680 R681 R678 R679 R677 R675 DS26 C110 C108 R193 DS27 HVDD C117 C118 R200 R197 U41 C141 R251 5 R284 J115 AA29 J119 Y30 J122 M23 J131 T27 J134 T26 J135 V23 J232 U24 W28 R29 R24 J105 J104 Y1 REFCLK0_P REFCLK0_N SERDES0 4 3 J111 V24 85 R2 1 U28 R161 R162 65 R2 U49 U46 4 3 J198 R190 HVSS U39 U38 R199 C113 R208 R209 R210 R211 C126 R222 J164 J121 5 J113 USB MICRO AB OTG Support 1 5 J106 1 C80 D7 U10 R69 R70 R73 J49 A14 P14 R28 4 2 C138 C81 C82 20 10 1 R196 R198 RESET U19 P1 C39 Q13 P3LED2 TC2 P3LED3 TC1 TC4 P3LED1 J32 P3LED0 TC3 TC6 P2LED3 P2LED2 TC5 TC7 P2LED0 R121 A1 3 1 J163 C136 R214 R216 HVSS R223 R225 C132 R224 U44 R228 1 C107 C106 R194 1 CR4 P1 R195 U22 GND J30 1 1 R117 R118 R119 R122 R125 R126 R127 R129 R133 R135 R136 R138 R139 R141 R144 R145 R85 R59 TP30 2 U43 C135 C115 R201 TP5 CR3 J94 1 R76 SW6 R58 L4 R64 1 C109 TP4 R191 - - 3 SFP CONN A12 M12 ZL RST 12 J4 6 U34 L9 1 J93 J107 J108 C83 R174 J120 FP4 HEADER R147 1 V22 J110 AA28 J114 W27 J118 TP8 DS24 U26 J63 J91 J99 J102 J101 J100 J98 R664 J92 R165 GND 1 J88 J60 J66 R171 J231 9 U69 1 J79 J136 J42 R169 1 REMOTE PWR ENB DS23 R134 10 1 U32 J83 6 1 R164 1 Q17 J75 J78 GND R51 U9 R66 R68 TP11 17 5 J74 J84 J89 J90 TP2 A1 R62 R65 GND J34 J72 J77 J40 J53 J69 J64 J87 1 19 R128 GND 2 10 J58 R142 J62 J68 R156 J73 U35 C122 J48 J41 J39 L6 J57 J86 J97 J85 J109 J45 9 J96 J71 C116 J28 J27 C55 C64 C65 1 1 5 R140 J65 J76 DB9-CAN2 3 1 U21 X1 U24 1 20 J51 2 19 J47 J50 J56 L11 20 R115 2 J13 SW3 SW4 C35 R105 U17 C56 D9 U18 J46 J61 J95 R63 R44 R98 U11 D8 ETM HEADER RS1 J35 1 GND 1 R41 C30 R42 C31 R43 J18 DB9-CAN1 R120 Q10 R67 R71 R72 R75 R77 R79 R84 REFP6 1 R116 DS21 2 1 5 DS20 VDD_REG 1 R124 REFP5 C47 1.2V J36 J52 U14 U13 1 RVI HEADER TP15 R101 TP19 C57 3P3V_LDO U16 M1 7 20 J5 J17 J20 3 J21 3 J22 3 J25 3 12 1 J7 R38 U7 C34 Q12 J23 C45 1 6 17 C20 U4 R33 C25 C26 C27 5 1 CR2 FTDI INTERFACE R96 J24 1 7 C694 SW2 R14 R29 C13 U5 C23 C24 1.0V CR1 J1 ed ed SW5 R13 D1 Q11 3 C41 1 1 SW7 TP1 C21 R57 ON USB MINI B J6 FMC HEADER C19 C18 R37 4 R34 1 C10 C17 10 1 R40 J9 1 1 R31 D3 C16 L3 C22 6 Q8 J8 GND U6 3 HPDIFFN4 HPDIFFP4 DS7 DS8 DS9 3P3V 5P0V C1 R10 C14 C15 2P5V J3 C3 C4 3P3V R17 R18 C11 R19 R20 1P8V Q7 1 C693 R9 D2 D4 C682 R16 C12 L2 TP23 OFF FMC HEADER L1 TP17 TP18 DC JACK12V/6A A1 A40 7 1 7 R15 C9 1 K1 12P0V DS4 DS5 DS6 VDD_REG U1 R11 C2 R669 R12 5P0V U3 C8 R6 Q5 GND R7 R8 C683 R660 Q6 R4 2P5V_LDO R5 2P5V Q4 DS3 R3 3P3V_LDO Q2 12V_POE Q3 R1 1P8V R2 DDR3-1P5V DS2 Q1 12V 12V_PCIE R668 C36 Q9 TP9 U2 12_DCJACK TP16 K40 1 J2 1 DS1 Appendix 4: Jumper Locations D19 C205 B49 Figure 18 • SmartFusion2 Development Kit Silkscreen Top View Figure 18 shows the jumper locations in the Development Kit board: • Jumpers highlighted in red are set by default. • Jumpers highlighted in green must be set manually. • The location of the jumpers in Figure 18 on page 27 are searchable. Revision 4 27 In-System Programming Using USB OTG Controller Interface Appendix 5: Error Codes Table 4 • Error Codes Define Error Code Description 1u Device contents mismatch #define MSS_SYS_UNEXPECTED_DATA_RECEIVED 2u Data is not supported #define MSS_SYS_INVALID_ENCRYPTION_KEY 3u Invalid encryption key #define MSS_SYS_INVALID_COMPONENT_HEADER 4u Invalid file header #define MSS_SYS_BACK_LEVEL_NOT_SATISFIED 5u corrupted /invalid bitstream #define MSS_SYS_DSN_BINDING_MISMATCH 7u corrupted /invalid bitstream #define MSS_SYS_ILLEGAL_COMPONENT_SEQUENCE 8u corrupted /invalid bitstream #define MSS_SYS_INSUFFICIENT_DEV_CAPABILITIES 9u Invalid Device capabilities #define MSS_SYS_INCORRECT_DEVICE_ID 10u Invalid Device id #define MSS_SYS_UNSUPPORTED_BITSTREAM_PROT_VER 11u bitstream is not supported #define MSS_SYS_VERIFY_NOT_PERMITTED_ON_BITSTR 12u Verification is not allowed for input bitstream #define MSS_SYS_ABORT 127u Operation aborted 129u eNVM verification failed #define MSS_SYS_DEVICE_SECURITY_PROTECTED 130u Device is secured #define MSS_SYS_PROGRAMMING_MODE_NOT_ENABLED 131u Programming mode is not enabled. Su pe rs #define MSS_SYS_NVM_VERIFY_FAILED ed ed #define MSS_SYS_CHAINING_MISMATCH 28 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Appendix 6: Generating .spi Programming File using Libero 1. Launch the Libero SoC software to open a Libero project for fabenvm.spi programming file. The Libero design file is provided in <download_folder>\sf2_isp_using_usb_interface_demo_df\sample_programming_file\fabric_and _envm. pe rs ed ed 2. Right-click Bitstream under Handoff Design for Production in the Design Flow tab, and click Export... from the context menu. Su Figure 19 • Configuring Export Bitstream Revision 4 29 In-System Programming Using USB OTG Controller Interface ed ed 3. On the Export Bitstream window, select the SPI file check box. 4. Click OK. rs Figure 20 • Export Programming File Options window Su pe 5. Double-click Export Bitstream under Handoff Design for Production in the Design Flow tab to generate the .spi file (Figure 19 on page 29). Figure 21 shows the .spi file location in Messages tab. Figure 21 • .SPI File Location 30 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide Appendix 7: Hardware Project Implementation Settings The following hardware project settings are required to build the demo design. Configuring the I/Os for Flash*Freeze Mode pe rs ed ed The Libero demo design configures M3_CLK to operate at 50 MHz, one UART interface (MMUART_1) for serial communication and USB OTG as mass storage class host. The FPGA fabric is not operational during Program or Verify operations as the device enters into Flash*Freeze(F*F). On the Development Kit board, the MMUART_0 TX and RX are connected to the mini-B USB through the fabric and fabric I/Os. During F*F mode, the fabric and I/Os are not available. So the MMUART_0 cannot be used as the serial communication interface. As such, MMUART_1 is used, and the RXD and TXD ports are configured using the I/O Editor to be available during F*F mode, as shown Figure 22. The user has to Commit and Check the settings from the File menu after configuring the ports. Su Figure 22 • Configuring MMUART_1 Ports to be Available During F*F Revision 4 31 In-System Programming Using USB OTG Controller Interface Standby Clock Source Configuration rs ed ed The standby clock source for the MSS in F*F mode is configured to On-chip 50 MHz RC Oscillator using the Flash*Freeze Hardware Settings dialog in the Libero SoC software, as shown in Figure 23. A higher MSS clock frequency is required in F*F mode to meet the MMUART baud rate requirements. Su pe Figure 23 • Flash*Freeze Hardware Settings Dialog 32 R e visio n 4 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface - Libero SoC v11.4 Demo Guide SoftConsole Project Generation rs ed ed The firmware and SoftConsole project workspace can be generated by checking the Create Project and selecting a Software IDE option in Libero project as shown in Figure 24. Figure 24 • Export Firmware Options Su pe On successful firmware generation, the firmware and SoftConsole folders are generated at <download_folder>\sf2_isp_using_usb_interface_demo_df\libero as specified in Location field of Export Firmware dialog box as shown in Figure 24. Revision 4 33 In-System Programming Using USB OTG Controller Interface Su pe rs ed ed For software modifications, open the SoftConsole Project workspace (located at <download_folder>\sf2_isp_using_usb_interface_demo_df\libero\SoftConsole\demo_MSS_CM3) using SoftConsole IDE v3.4 SP1. Figure 25 shows SoftConsole Project workspace. Figure 25 • SoftConsole Project Workspace The SoftConsole workspace consists of three projects. 34 • demo_MSS_CM3_app This project displays the available programming files from USB mass storage device. This project receives the bitstream from HostPC through UART interface and invokes the system controller programming services. • demo_MSS_CM3_boot_loader This project implements the remapping the eSRAM to Cortex-M3 processor code space after copying the ISP code to eSARM from eNVM. • demo_MSS_CM3_hw_platform This project contains all the firmware and hardware abstraction layers that correspond to the hardware design. This project is configured as a library and is referenced by demo_MSS_CM3_app and demo_MSS_CM3_boot_loader application projects. The contents of this folder get over-written every time the firmware is exported as shown in Figure 24. R e visio n 4 A – List of Changes The following table lists critical changes that were made in each revision of the chapter in the demo guide. Date Changes Page Updated the document for Libero v11.4 software release (SAR 59740). NA Revision 3 (May 2014) Updated the document for Libero v11.3 software release (SAR 56662). NA Revision 2 (December 2013) Updated "Demo Design Description" section (SAR 53451). Revision 1 (November 2013) Updated the document for Libero v11.2 software release (SAR 52963). NA Revision 0 (October 2013) Initial release. NA 8 Su pe rs ed ed Revision 4 (August 2014) Revision 4 35 B – Product Support Microsemi SoC Products Group backs its products with various support services, including Customer Service, Customer Technical Support Center, a website, electronic mail, and worldwide sales offices. This appendix contains information about contacting Microsemi SoC Products Group and using these support services. Customer Service ed ed Contact Customer Service for non-technical product support, such as product pricing, product upgrades, update information, order status, and authorization. From North America, call 800.262.1060 From the rest of the world, call 650.318.4460 Fax, from anywhere in the world, 408.643.6913 Customer Technical Support Center rs Microsemi SoC Products Group staffs its Customer Technical Support Center with highly skilled engineers who can help answer your hardware, software, and design questions about Microsemi SoC Products. The Customer Technical Support Center spends a great deal of time creating application notes, answers to common design cycle questions, documentation of known issues, and various FAQs. So, before you contact us, please visit our online resources. It is very likely we have already answered your questions. Technical Support pe Visit the Customer Support website (www.microsemi.com/soc/support/search/default.aspx) for more information and support. Many answers available on the searchable web resource include diagrams, illustrations, and links to other resources on the website. Website Su You can browse a variety of technical and non-technical information on the SoC home page, at www.microsemi.com/soc. Contacting the Customer Technical Support Center Highly skilled engineers staff the Technical Support Center. The Technical Support Center can be contacted by email or through the Microsemi SoC Products Group website. Email You can communicate your technical questions to our email address and receive answers back by email, fax, or phone. Also, if you have design problems, you can email your design files to receive assistance. We constantly monitor the email account throughout the day. When sending your request to us, please be sure to include your full name, company name, and your contact information for efficient processing of your request. The technical support email address is [email protected]. Revision 4 36 SmartFusion2 SoC FPGA In-System Programming Using USB OTG Controller Interface -Libero SoC v11.4 Demo Guide My Cases Microsemi SoC Products Group customers may submit and track technical cases online by going to My Cases. Outside the U.S. Customers needing assistance outside the US time zones can either contact technical support via email ([email protected]) or contact a local sales office. Sales office listings can be found at www.microsemi.com/soc/company/contact/default.aspx. ITAR Technical Support Su pe rs ed ed For technical support on RH and RT FPGAs that are regulated by International Traffic in Arms Regulations (ITAR), contact us via [email protected]. Alternatively, within My Cases, select Yes in the ITAR drop-down list. For a complete list of ITAR-regulated Microsemi FPGAs, visit the ITAR web page. Revision 4 37 ed ed rs pe Su Microsemi Corporate Headquarters One Enterprise, Aliso Viejo CA 92656 USA Within the USA: +1 (800) 713-4113 Outside the USA: +1 (949) 380-6100 Sales: +1 (949) 380-6136 Fax: +1 (949) 215-4996 E-mail: [email protected] Microsemi Corporation (Nasdaq: MSCC) offers a comprehensive portfolio of semiconductor and system solutions for communications, defense and security, aerospace, and industrial markets. Products include high-performance and radiation-hardened analog mixed-signal integrated circuits, FPGAs, SoCs, and ASICs; power management products; timing and synchronization devices and precise time solutions, setting the world's standard for time; voice processing devices; RF solutions; discrete components; security technologies and scalable anti-tamper products; Power-over-Ethernet ICs and midspans; as well as custom design capabilities and services. Microsemi is headquartered in Aliso Viejo, Calif. and has approximately 3,400 employees globally. Learn more at www.microsemi.com. © 2014 Microsemi Corporation. All rights reserved. Microsemi and the Microsemi logo are trademarks of Microsemi Corporation. All other trademarks and service marks are the property of their respective owners. 50200471-4/08.14