LT5578 - 0.4GHz to 2.7GHz High Linearity Upconverting Mixer

LT5578
0.4GHz to 2.7GHz
High Linearity
Upconverting Mixer
FEATURES
DESCRIPTION
n
The LT®5578 mixer is a high performance upconverting
mixer optimized for frequencies in the 0.4GHz to 2.7GHz
range. The single-ended LO input and RF output ports
simplify board layout and reduce system cost. The mixer
needs only –1dBm of LO power and the balanced design
results in low LO signal leakage to the RF output. At
1.95GHz operation, the LT5578 provides conversion gain
of –0.7dB, high OIP3 of 24.3dBm and a low noise floor of
–158dBm/Hz at a –5dBm RF output signal level.
n
n
n
n
n
n
n
n
High Output IP3: 27dBm at 0.9GHz
24.3dBm at 1.95GHz
Low Noise Floor: –158dBm/Hz (POUT = –5dBm)
High Conversion Gain: 1.4dB at 0.9GHz
Noise Figure: 8.6dB
Low LO-RF Leakage: –43dBm
Single-Ended RF and LO Ports
Low LO Drive Level: –1dBm
Single 3.3V Supply
5mm × 5mm QFN24 Package
(Pin Compatible with LT5579)
The LT5578 offers a high performance alternative to passive mixers. Unlike passive mixers, which have conversion
loss and require high LO drive levels, the LT5578 delivers
conversion gain at significantly lower LO input levels and
is less sensitive to LO power level variations. The lower
LO drive level requirements, combined with the excellent
LO leakage performance, translate into lower LO signal
contamination of the output signal.
APPLICATIONS
n
n
n
n
GSM 900PCS/1800PCS and W-CDMA Infrastructure
LTE and WiMAX Basestations
Wireless Repeaters
Public Safety Radios
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
Frequency Upconversion in LTE Transmitter
LO INPUT
–1dBm
2.7pF
Gain, NF and OIP3 vs
RF Output Frequency
6.8pF
30
OIP3
LO
GND
13.7Ω
IF
140MHz
TC4-1W+
220pF
4:1
100nH
IF+
39pF
220pF
BIAS
22nH
RF
2pF
IF–
RF
700MHz
13nH TO 950MHz
2.7pF
GAIN (dB), NF (dB), OIP3 (dBm)
LT5578
25
20
TA = 25°C
fIF = 140MHz
fLO = fRF – fIF
15
10
SSB NF
5
GAIN
100nH
13.7Ω
VCC
10μF
100μF
5579 TA01a
1nF
VCC
3.3V
0
650 700 750 800 850 900 950 1000
RF OUTPUT FREQUENCY (MHz)
5578 TA01b
5578f
1
LT5578
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
Supply Voltage ............................................................4V
LO Input Power ....................................................10dBm
LO Input DC Current ..............................................30mA
RF Output DC Current ............................................45mA
IF Input Power (Differential).................................18dBm
IF+, IF– DC Currents ...............................................45mA
TJMAX .................................................................... 150°C
Operating Temperature Range.................. –40°C to 85°C
Storage Temperature Range................... –65°C to 150°C
GND
GND
GND
LO
GND
GND
TOP VIEW
24 23 22 21 20 19
GND 1
18 GND
GND 2
17 GND
IF+ 3
16 GND
25
IF– 4
15 RF
GND
9 10 11 12
VCC
8
VCC
7
VCC
13 GND
VCC
14 GND
GND 6
GND
GND 5
UH PACKAGE
24-LEAD (5mm s 5mm) PLASTIC QFN
TJMAX = 150°C, θJA = 34°C/W
EXPOSED PAD (PIN 25) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT5578IUH#PBF
LT5578IUH#TRPBF
5578
24-Lead (5mm × 5mm) Plastic QFN
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
DC ELECTRICAL CHARACTERISTICS
PARAMETER
VCC = 3.3V, TA = 25°C (Note 3), unless otherwise noted.
CONDITIONS
MIN
TYP
MAX
UNITS
Power Supply Requirements (VCC)
Supply Voltage
3.3
3.5
VDC
Supply Current
VCC = 3.3V, PLO = –1dBm
VCC = 3.5V, PLO = –1dBm
3.1
152
159
170
mA
mA
Input Common Mode Voltage (VCM)
Internally Regulated
565
AC ELECTRICAL CHARACTERISTICS
PARAMETER
CONDITIONS
IF Input Frequency Range (Note 4)
Requires Matching
LO Input Frequency Range (Note 4)
RF Output Frequency Range (Note 4)
mV
(Notes 2, 3)
MIN
TYP
MAX
UNITS
LF to 600
MHz
Requires Matching Below 1.5GHz
400 to 3000
MHz
Requires Matching
400 to 2700
MHz
5578f
2
LT5578
AC ELECTRICAL CHARACTERISTICS VCC = 3.3V, TA = 25°C, Test circuits are shown in Figure 1. (Notes 2, 3)
PARAMETER
IF Input Return Loss
LO Input Return Loss
RF Output Return Loss
LO Input Power
CONDITIONS
ZO = 50Ω, External Match
ZO = 50Ω, External Match
ZO = 50Ω, External Match
MIN
TYP
15
>9
>10
–5 to 2
MAX
UNITS
dB
dB
dB
dBm
MAX
UNITS
dB
dB
dB
dB/°C
dB/°C
dB/°C
dBm
dBm
dBm
dBm
dBm
dBm
dB
dB
dB
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm
dBm
dBm
dB
dB
dB
dBm
dBm
dBm
dBm
dBm
dBm
VCC = 3.3V, TA = 25°C, PIF = –5dBm (–5dBm/tone for 2-tone tests, Δf = 1MHz), PLO = –1dBm, unless otherwise noted.
Low side LO for 900MHz. High side LO for 740MHz and 1950MHz. (Notes 2, 3, 4)
PARAMETER
Conversion Gain
Conversion Gain vs Temperature
(TA = –40°C to 85°C)
Output 3rd Order Intercept
Output 2nd Order Intercept (LO ±2IF)
Single Sideband Noise Figure
Output Noise: POUT = –5dBm
Output Noise: POUT = 0dBm
Output Noise: POUT = 5dBm
Output 1dB Compression
IF to LO Isolation
LO to IF Leakage
LO to RF Leakage
CONDITIONS
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
fRF = 740MHz, fIF = 140MHz
fRF = 900MHz, fIF = 140MHz
fRF = 1950MHz, fIF = 240MHz
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Each set of frequency conditions requires appropriate matching
(see Figure 1).
MIN
TYP
0.8
1.4
–0.7
–0.020
–0.018
–0.021
26.5
27.0
24.3
62
52
58
8.6
8.6
10.5
–161
–160.5
–158
–158
–157.5
–154
–154
–153
–149.5
11.6
12
10
80
75
60
–31
–40
–22
–43
–43
–46
Note 3: The LT5578 is guaranteed functional over the operating
temperature range from –40°C to 85°C.
Note 4: SSB noise figure measurements performed with a small-signal
noise source and bandpass filter on LO signal generator. No other IF signal
applied.
5578f
3
LT5578
TYPICAL DC PERFORMANCE CHARACTERISTICS
(Test Circuit Shown in Figure 1)
Supply Current vs Supply Voltage
180
SUPPLY CURRENT (mA)
170
160
150
140
85°C
25°C
–40°C
130
120
3.0
3.2
3.3
3.4
SUPPLY VOLTAGE (V)
3.1
3.5
3.6
5578 G01
TYPICAL AC PERFORMANCE CHARACTERISTICS
900MHz Application:
VCC = 3.3V, TA = 25°C, fIF = 140MHz, PIF = –5dBm (–5dBm/tone for 2-tone tests, Δf = 1MHz), low side LO, PLO = –1dBm,
output measured at 900MHz, unless otherwise noted. (Test circuit shown in Figure 1)
Gain Distribution at 900MHz
25
TA = 90°C
TA = 25°C
TA = –45°C
40
20
DISTRIBUTION (%)
DISTRIBUTION (%)
35
30
25
20
15
10
60
TA = 90°C
TA = 25°C
TA = –45°C
15
10
5
0
0.5
1.0 1.5 2.0
GAIN (dB)
2.5
3.0 3.5
5578 G02
0
40
30
20
10
5
0
–0.5
TA = 90°C
TA = 25°C
TA = –45°C
50
DISTRIBUTION (%)
45
SSB Noise Figure Distribution at
900MHz
OIP3 Distribution at 900MHz
23
24
25
26
27
OIP3 (dBm)
28
29
5578 G03
0
6
7
8
9
NOISE FIGURE (dB)
10
11
5578 G04
5578f
4
LT5578
TYPICAL AC PERFORMANCE CHARACTERISTICS
740MHz Application:
VCC = 3.3V, TA = 25°C, fIF = 140MHz, PIF = –5dBm (–5dBm/tone for 2-tone tests, Δf = 1MHz), high side LO, PLO = –1dBm,
output measured at 740MHz, unless otherwise noted. (Test circuit shown in Figure 1)
Conversion Gain and OIP3
vs RF Output Frequency
SSB Noise Figure
vs RF Output Frequency
30
16
0
18
OIP3
16
–10
85°C
25°C
–40°C
4
18
GAIN
14
12
10
8
85°C
25°C
–40°C
4
–4
660
680
700 720 740 760
RF FREQUENCY (MHz)
2
660 680
10
800
780
720 740 760
RF FREQUENCY (MHz)
780
700
–30
–40
85°C
25°C
–40°C
–50
–60
660
800
680
700 720 740 760
RF FREQUENCY (MHz)
780
Conversion Gain and OIP3
vs LO Input Power
SSB Noise Figure
vs LO Input Power
30
800
5578 G07
5578 G06
5578 G05
16
–20
6
14
0
LO LEAKAGE (dBm)
22
OIP3 (dBm)
8
NOISE FIGURE (dB)
26
12
GAIN (dB)
LO-RF Leakage
vs RF Output Frequency
Conversion Gain and OIP3
vs Supply Voltage
30
16
18
OIP3
OIP3
16
26
12
10
8
6
14
0
GAIN (dB)
18
GAIN
NOISE FIGURE (dB)
GAIN (dB)
4
12
–4
–17
2
–17
10
–13
–5
–1
–9
LO INPUT POWER (dBm)
3
4
–4
–9
–13
–5
–1
LO INPUT POWER (dBm)
5578 G08
85°C
25°C
–40°C
14
3
3.0
3.1
5578 G10
IM2 Level
vs RF Output Power (1-Tone)
0
0
–20
–20
10
3.5
3.2
3.3
3.4
SUPPLY VOLTAGE (V)
5578 G09
IM3 Level
vs RF Output Power (2-Tone)
18
GAIN
0
85°C
25°C
–40°C
4
22
8
OIP3 (dBm)
22
85°C
25°C
–40°C
OIP3 (dBm)
8
26
12
14
SSB Noise Figure
vs Supply Voltage
18
–40
–60
14
NOISE FIGURE (dB)
IM2 LEVEL (dBc)
IM3 LEVEL (dBc)
16
–40
–60
12
10
8
6
–80
–80
85°C
25°C
–40°C
–100
2
4
–12 –10 –8 –6 –4 –2 0
RF OUTPUT POWER (dBm/TONE)
6
5578 G11
–100
2
–12 –10 –8 –6 –4 –2 0
RF OUTPUT POWER (dBm)
85°C
25°C
–40°C
4
85°C
25°C
–40°C
4
6
5578 G12
2
3.0
3.1
3.4
3.2
3.3
SUPPLY VOLTAGE (V)
3.5
5578 G13
5578f
5
LT5578
TYPICAL AC PERFORMANCE CHARACTERISTICS
900MHz Application:
VCC = 3.3V, TA = 25°C, fIF = 140MHz, PIF = –5dBm (–5dBm/tone for 2-tone tests, Δf = 1MHz), low side LO, PLO = –1dBm,
output measured at 900MHz, unless otherwise noted. (Test circuit shown in Figure 1)
Conversion Gain and OIP3
vs RF Output Frequency
SSB Noise Figure
vs RF Output Frequency
30
16
LO-RF Leakage
vs RF Output Frequency
0
18
OIP3
16
–10
26
12
85°C
25°C
–40°C
4
18
GAIN
12
10
8
85°C
25°C
–40°C
4
–4
830
850
870 890 910 930
RF FREQUENCY (MHz)
10
970
950
–20
–30
–40
6
14
0
LO LEAKAGE (dBm)
GAIN (dB)
22
OIP3 (dBm)
8
NOISE FIGURE (dB)
14
2
830
850
870
890 910 930
RF FREQUENCY (MHz)
950
5578 G14
85°C
25°C
–40°C
–50
–60
830
970
850
870 890 910 930
RF FREQUENCY (MHz)
950
5578 G16
5578 G15
Conversion Gain and OIP3
vs LO Input Power
SSB Noise Figure
vs LO Input Power
30
16
970
Conversion Gain and OIP3
vs Supply Voltage
30
16
18
OIP3
OIP3
16
0
12
GAIN (dB)
NOISE FIGURE (dB)
GAIN (dB)
18
GAIN
14
10
8
6
14
–4
–17
–13
–5
–1
–9
LO INPUT POWER (dBm)
3
10
2
–17
4
–4
–9
–1
–13
–5
LO INPUT POWER (dBm)
3
5578 G17
14
3.0
3.1
0
–20
–20
10
3.5
3.2
3.3
3.4
SUPPLY VOLTAGE (V)
5578 G19
IM2 Level
vs RF Output Power (1-Tone)
0
18
GAIN
5578 G18
IM3 Level
vs RF Output Power (2-Tone)
22
85°C
25°C
–40°C
0
85°C
25°C
–40°C
4
8
OIP3 (dBm)
4
22
OIP3 (dBm)
85°C
25°C
–40°C
8
26
12
26
12
SSB Noise Figure
vs Supply Voltage
18
16
–40
–60
–80
–100
2
4
–12 –10 –8 –6 –4 –2 0
RF OUTPUT POWER (dBm/TONE)
–40
–60
–80
85°C
25°C
–40°C
6
5578 G20
NOISE FIGURE (dB)
IM2 LEVEL (dBc)
IM3 LEVEL (dBc)
14
–100
2
–12 –10 –8 –6 –4 –2 0
RF OUTPUT POWER (dBm)
12
10
8
6
85°C
25°C
–40°C
4
85°C
25°C
–40°C
4
6
5578 G21
2
3.0
3.1
3.2
3.4
3.3
SUPPLY VOLTAGE (V)
3.5
5578 G22
5578f
6
LT5578
TYPICAL PERFORMANCE CHARACTERISTICS
1950MHz Application:
VCC = 3.3V, TA = 25°C, fIF = 240MHz, PIF = –5dBm (–5dBm/tone for 2-tone tests, Δf = 1MHz), high side LO, PLO = –1dBm,
output measured at 1950MHz, unless otherwise noted. (Test circuit shown in Figure 1)
Conversion Gain and OIP3
vs RF Output Frequency
16
SSB Noise Figure
vs RF Output Frequency
28
OIP3
LO-RF Leakage
vs RF Output Frequency
0
18
16
–10
24
85°C
25°C
–40°C
4
16
GAIN
0
LO LEAKAGE (dBm)
20
14
NOISE FIGURE (dB)
8
OIP3 (dBm)
GAIN (dB)
12
12
10
8
85°C
25°C
–40°C
4
1700
2
1600
8
2200
1800 1900 2000 2100
RF FREQUENCY (MHz)
1700
1800 1900 2000 2100
RF FREQUENCY (MHz)
5578 G23
–40
85°C
25°C
–40°C
–50
–60
1600 1700 1800 1900 2000 2100 2200 2300
RF FREQUENCY (MHz)
2200
5578 G25
5578 G24
Conversion Gain and OIP3
vs LO Input Power
SSB Noise Figure
vs LO Input Power
16
–30
6
12
–4
1600
–20
28
Conversion Gain and OIP3
vs Supply Voltage
16
18
OIP3
28
OIP3
16
12
4
16
GAIN
12
10
8
–13
–5
–1
–9
LO INPUT POWER (dBm)
3
8
2
–17
4
–4
–9
–1
–13
–5
LO INPUT POWER (dBm)
3
5578 G26
3.0
3.1
0
–20
–20
8
3.5
3.2
3.3
3.4
SUPPLY VOLTAGE (V)
5578 G28
IM2 Level
vs RF Output Power (1-Tone)
0
16
12
5578 G27
IM3 Level
vs RF Output Power (2-Tone)
20
85°C
25°C
–40°C
0
85°C
25°C
–40°C
4
–4
–17
8
GAIN
6
12
0
GAIN (dB)
20
85°C
25°C
–40°C
24
14
OIP3 (dBm)
8
NOISE FIGURE (dB)
24
OIP3 (dBm)
GAIN (dB)
12
SSB Noise Figure
vs Supply Voltage
18
–40
–60
NOISE FIGURE (dB)
IM2 LEVEL (dBc)
IM3 LEVEL (dBc)
16
–40
–60
14
12
10
8
6
–80
–80
85°C
25°C
–40°C
–100
2
–14 –12 –10 –8 –6 –4 –2 0
RF OUTPUT POWER (dBm/TONE)
4
5578 G29
–100
–14 –12 –10 –8 –6 –4 –2 0
RF OUTPUT POWER (dBm)
85°C
25°C
–40°C
2
85°C
25°C
–40°C
4
4
5578 G30
2
3.0
3.1
3.2
3.4
3.3
SUPPLY VOLTAGE (V)
3.5
5578 G31
5578f
7
LT5578
PIN FUNCTIONS
GND (Pins 1, 2, 5-7, 12-14, 16-21, 23, 24): Ground
Connections. These pins are internally connected to the
exposed pad and should be soldered to a low impedance
RF ground on the printed circuit board.
IF+, IF– (Pins 3, 4): Differential IF Input. The common
mode voltage on these pins is set internally to 565mV. The
DC current from each pin is determined by the value of
an external resistor to ground. The maximum DC current
through each pin is 45mA.
VCC (Pins 8-11): Power Supply Pins for the IC. These
pins are connected together internally. Typical current
consumption is 152mA. These pins should be connected
together on the circuit board with external bypass capacitors of 1000pF, 100pF and 10pF located as close to the
pins as possible.
RF (Pin 15): Single-Ended RF Output. This pin is connected to an internal transformer winding. The opposite
end of the winding is grounded internally. An impedance
transformation may be required to match the output and a
DC decoupling capacitor is required if the following stage
has a DC bias voltage present.
LO (Pin 22): Single-Ended Local Oscillator Input. An internal
series capacitor acts as a DC block to this pin.
Exposed Pad (Pin 25): PGND. Electrical and thermal
ground connection for the entire IC. This pad must be
soldered to a low impedance RF ground on the printed
circuit board. This ground must also provide a path for
thermal dissipation.
BLOCK DIAGRAM
25
15
EXPOSED
PAD
RF
VCC
22
LO
DOUBLE
BALANCED
MIXER
LO BUFFER
VCC
VCC2
BIAS
VCC2
VCC
10
9
8
VCM
CTRL
IF+
3
GND PINS ARE NOT SHOWN
VCC
11
IF–
4
5578 BD
5578f
8
LT5578
TEST CIRCUIT
LO INPUT
C13
Z1
C12
R1
C9
TL2
C3
4
5
C2
L2
6
R2
GND
GND
LO
GND
GND
GND
IF+
GND
GND
IF–
RF
GND
GND
GND
GND
7
8
9
18
17
16
L3
15
14
C8
TL3
RF
OUTPUT
C14
13
GND
IF
INPUT
GND
VCC
3
GND
VCC
TL1
GND
VCC
2
GND
1
VCC
L1
C1
GND
T1
4:1
24 23 22 21 20 19
10 11 12
VCC
C4
C5
C6
C7
5578 F01
fRF = 740MHz
fIF = 140MHz
fLO = 880MHz
fRF = 900MHz
fIF = 140MHz
fLO = 760MHz
fRF = 1950MHz
fIF = 240MHz
fLO = 2190MHz
SIZE
COMMENTS
220pF
220pF
82pF
0402
AVX
C3
–
–
4.7pF
0402
AVX
C4
100pF
100pF
100pF
0402
AVX
C5
10pF
10pF
10pF
0402
AVX
C6
1nF
1nF
1nF
0402
AVX
C7
1μF
1μF
1μF
0603
Taiyo Yuden LMK107BJ105MA
C8
3.3pF
1.8pF
–
0402
AVX ACCU-P
C9
39pF
39pF
33pF
0402
AVX
C12
–
–
–
0402
C13
–
2.7pF
–
0402
C14
–
–
1.2pF
0402
100nH
100nH
100nH
0603
Coilcraft 0603CS
REF DES
C1, C2
L1, L2
L3
R1, R2
T1
18nH
12nH
1.8nH
0402
Toko LL1005-FHL
13.7, 0.1%
13.7, 0.1%
13.7, 0.1%
0603
IRC PFC-W0603LF-02-13R7-B
4:1
4:1
4:1
AT224-1
Mini-Circuits TC4-1W+
–
–
1.9mm
–
ZO = 70Ω
TL3
2.3mm
2.3mm
1.3mm
–
ZO = 70Ω
Z1
2.6pF
6.8pF
0Ω
0402
TL1, TL2*
AVX/0Ω Jumper
*Center-to-center spacing between C9 and C3. Center of C9 is 3.0mm from the edge of the package.
Figure 1. Test Circuit Schematic and Component Values
5578f
9
LT5578
APPLICATIONS INFORMATION
The LT5578 uses a high performance LO buffer amplifier
driving a double-balanced mixer core to achieve frequency
conversion with high linearity. Internal baluns are used to
provide single-ended LO input and RF output ports. The
IF input is differential. The LT5578 is intended for operation in the 0.4GHz to 2.7GHz frequency range, though
operation outside this range is possible with reduced
performance.
L1 and L2 should connect to the signal lines as close to
the package as possible. This location will be at the lowest
impedance point, which will minimize the sensitivity of the
performance to the loading of the shunt L-R branches.
IF Input Interface
The differential input resistance to the mixer is approximately 10Ω, as indicated in Table 1. The package and
external inductances (TL1 and TL2) are used along with
C9 to step the impedance up to about 12.5Ω. At lower
frequencies additional series inductance may be required
between the IF ports and C9. The position of C9 may vary
with the IF frequency due to the different series inductance
requirements. The 4:1 impedance ratio of transformer T1
completes the transformation to 50Ω. Table 1 lists the
differential IF input impedances and reflection coefficients
for several frequencies.
The IF inputs are tied to the emitters of the double-balanced
mixer transistors, as shown in Figure 2. These pins are
internally biased to a common mode voltage of 565mV.
The optimum DC current in the mixer core is approximately
40mA per side, and is set by the external resistors, R1 and
R2. The inductors and resistors must be able to handle
the anticipated current and power dissipation. For best
LO leakage performance the board layout must be symmetrical and the input resistors should be well matched
(0.1% tolerance is recommended).
The purpose of the inductors (L1 and L2) is to reduce the
loading effects of R1 and R2. The impedances of L1 and
L2 should be at least several times greater than the IF input
impedance at the desired IF frequency. The self-resonant
frequency of the inductors should also be at least several
times the IF frequency. Note that the DC resistances of L1
and L2 will affect the DC current and should be accounted
for in the selection of R1 and R2.
R1
IF
INPUT
LT5578
T1
4:1
C1
L1
40mA
TL1
3
IF+
C2
VCC
C3
2k
TL2
4
L2
IF–
565mV
40mA
5578 F02
R2
Table 1. IF Input Differential Impedance
FREQUENCY
(MHz)
IF INPUT
IMPEDANCE
70
REFLECTION COEFFICIENT
MAG
ANGLE
10.0 + j1.1
0.666
177.4
140
10.2 + j1.5
0.661
176.5
170
8.7 + j1.8
0.705
175.7
190
8.7 + j2.0
0.705
175.2
240
8.7 + j2.5
0.705
174.0
380
8.7 + j3.9
0.704
170.9
450
8.7 + j4.5
0.705
169.3
750
9.6 + j7.6
0.683
162.0
1000
9.8 + j10.3
0.685
155.9
The purpose of capacitor C3 is to improve the LO-RF
leakage in some applications. This relatively small-valued
capacitor has little effect on the impedance match in most
cases. This capacitor should typically be located close to
the IC, however, there may be cases where re-positioning
the capacitor will improve performance.
565mV
2k
C9
Capacitors C1 and C2 are used to cancel out the parasitic
series inductance of the IF transformer. They also provide
DC isolation between the IF ports to prevent unwanted interactions that can affect the LO to RF leakage performance.
The measured return loss of the IF input is shown in
Figure 3 for application frequencies of 70MHz, 140MHz
and 240MHz. Component values are listed in Table 2. All
of the applications use L1 = L2 = 100nH, R1 = R2 =13.7Ω
Figure 2. IF Input with External Matching
5578f
10
LT5578
APPLICATIONS INFORMATION
and T1 = TC4-1W+. The 70MHz match was not used for
140MHz characterization because it requires the addition
of two inductors.
EXTERNAL
MATCHING
LO
INPUT
Z1
22
Table 2. IF Input Component Values
C12
C13
FREQUENCY
(MHz)
C1, C2
(pF)
C9
(pF)
C3
(pF)
70
560
82
–
3.3
50-215
140
220
39
–
–
98-187
240
82
33
4.7
–
175-295
LO
VBIAS
TL1, TL2 MATCH BW
(nH)
(at 12dB RL)
5578 F04
Figure 4. LO Input Circuit
0
SEE FIGURES 1 AND 8 FOR
COMPONENT VALUES
0
RETURN LOSS (dB)
–5
RETURN LOSS (dB)
–5
–10
–15
d
–15
–20
–20
a
–25
–30
–10
–25
c
50
100
b
b
150
200
250
FREQUENCY (MHz)
300
c
a
0
500
1000 1500 2000
FREQUENCY (MHz)
2500
350
5578 F03
Figure 3. IF Input Return Loss with 70MHz (a),
140MHz (b) and 240MHz (c) Matching
LO Input Interface
The simplified schematic for the single-ended LO input port
is shown in Figure 4. An internal transformer provides a
broadband impedance match and performs single-ended
to differential conversion. The primary winding is internally
grounded, thus an external DC block may be necessary
in some applications. The transformer secondary feeds
the differential limiting amplifier stages that drive the
mixer core.
The measured return loss of the LO input port is shown in
Figure 5 for different application frequencies. The impedance match is acceptable from about 1.5GHz to beyond
3GHz, with a minimum return loss across this range of
about 9dB. Below 1.5GHz, external components are used
to tune the impedance match to the desired frequency.
3000
5578 F05
Figure 5. LO Input Return Loss with 520MHz (a),
760MHz (b), 880MHz (c) and >1.5GHz (d) Matching
Table 3 lists the input impedance and reflection coefficient
vs frequency for the LO input for use in such cases.
Table 3. Single-Ended LO Input Impedance
(at Pin 22, No External Match)
FREQUENCY
(MHz)
LO INPUT
IMPEDANCE
300
41.7||j20.3
600
900
1200
REFLECTION COEFFICIENT
MAG
ANGLE
0.747
142.8
95.0||j42.7
0.657
105.5
126||j84.2
0.558
67.6
127||j239
0.456
27.6
1500
104||–j686
0.353
–10.8
1800
74.0||–j188
0.247
–48.3
2100
52.5||–j162
0.158
–90.0
2400
42.3||–j459
0.097
–152.0
2700
44.4||j249
0.111
127.5
3000
52.4||j161
0.159
90.6
5578f
11
LT5578
APPLICATIONS INFORMATION
RF Output Interface
The RF output interface is shown in Figure 6. An internal
RF transformer reduces the mixer core output impedance
to simplify matching of the RF output pin. A center tap in
the transformer provides the DC connection to the mixer
core and the transformer provides DC isolation to the RF
output. The RF pin is internally grounded through the
secondary winding of the transformer, thus a DC voltage
should not be applied to this pin.
While the LT5578 performs best at frequencies above
700MHz, the part can be used down to 400MHz. The low
inductance of the internal transformer limits the performance at lower frequencies. The impedance data for the RF
output, listed in Table 4, can be used to develop matching
networks for different frequencies or load impedances.
Figure 7 illustrates the output return loss performance
for several applications. The component values and approximate matching bandwidths are listed in Table 5.
DC and RF Grounding
The LT5578 relies on the back side ground for both RF
and thermal performance. The Exposed Pad must be
soldered to the low impedance topside ground plane of
the board. As many vias as possible should connect the
topside ground to other ground layers to aid in thermal
dissipation and reduce inductance.
Table 4. Single-Ended RF Output Impedance
(at Pin 15, No External Matching)
FREQUENCY
(MHz)
RF OUTPUT
IMPEDANCE
400
800
REFLECTION COEFFICIENT
MAG
ANGLE
10.1 + j29.3
0.741
117.6
90.8 + j96.6
0.614
32.6
1200
69.7 – j66.6
0.507
–44.4
1600
32.8 – j22.5
0.330
–112.3
2000
32.3 – j5.4
0.225
–159.3
2400
28.6 + j0.3
0.273
179.0
2800
22.5 + j4.4
0.384
167.3
Table 5. RF Output Component Values
FREQUENCY
(MHz)
C8 (pF)
MATCH BW
(at 12dB RL)
L3 (nH) C14 (pF)
450
9.0
18
–
430-505
740
3.3
18
–
680-768
900
1.8
12
–
835-970
1950
–
1.8
1.2
1765-2305
2600
–
0Ω
0.8
2150-2990
0
LT5578
RF
50Ω
15
C8
8
9
10
11
5578 F06
C14
–5
RETURN LOSS (dB)
L3
–10
–15
–20
a
VCC
–25
Figure 6. RF Output Circuit
d
b
c
0
500
1000 1500 2000
FREQUENCY (MHz)
e
2500
3000
5578 F07
Figure 7. RF Output Return Loss with 450MHz (a), 740MHz (b),
900MHz (c), 1950MHz (d) and 2600MHz (e) Matching
5578f
12
LT5578
TYPICAL APPLICATIONS
The following examples illustrate the implementation and
performance of the LT5578 in some selected applications.
These circuits were evaluated using the board layout
shown in Figure 12.
Figure 9 shows measured conversion gain, noise figure
and OIP3 as a function of RF output frequency. At 450MHz,
the gain is –2.1dB with a NF of 9.3dB and an OIP3 of
23.8dBm.
12
450MHz Application
32
30
10
At the IF input, the 560pF capacitors are used mainly as
DC blocks, but also help tune out the parasitic inductance
of the transformer. The 82pF differential capacitor and
3.3nH chip inductors provide an impedance transformation between the IF input pins and the transformer. The
relatively low input frequency requires the use of chip
inductors instead of the short transmission lines that are
shown in Figure 2. The measured IF port return loss is
included in Figure 3.
The RF port impedance match is realized with a shunt 12pF
capacitor and a series 18nH inductor. The return loss with
this configuration is better than 12dB from about 430MHz
to 505MHz and is plotted in Figure 7.
To tune the LO port, a series 6.8pF and shunt 4.7pF capacitor are used as shown. This combination provides a
10dB, or better, return loss from 435MHz to 580MHz as
shown in Figure 5. The series capacitor also provides DC
decoupling for the internal transformer at the LO input.
SSB NF
GAIN (dB), NF (dB)
8
28
6
26
4
24
OIP3
TA = 25°C
fIF = 70MHz
PIF = –5dBm/TONE
2
0
GAIN
–2
–4
420
22
OIP3 (dBm)
In this case, the LT5578 was evaluated for an application
with an IF input at 70MHz, an RF output of 450MHz and
a high side LO. The LO port is tuned for high side LO injection at 520MHz. The matching networks for the three
ports are shown in Figure 8.
20
18
460
440
480
RF OUTPUT FREQUENCY (MHz)
16
500
5578 F09
Figure 9. Gain, Noise Figure and OIP3 vs RF Frequency
in the 450MHz Application
2600MHz Application
For this application, the impedance match of the RF port is
optimized at 2600MHz and has a good return loss over the
range of 2200MHz to 2900MHz. The component values are
listed in Table 5 and typical output return loss is shown in
Figure 7. The IF input is matched at 240MHz as described
in Table 2. The LO port requires no external matching for
this band as its return loss is good for frequencies above
1.5GHz.
LO
520MHz
6.8pF
13.7Ω
4.7pF
100nH
TC4-1W+
560pF
4:1
3.3nH
18nH
IF
70MHz
82pF
RF
450MHz
3.3nH
12pF
5578 F08
560pF
100nH
13.7Ω
Figure 8. Schematic for 450MHz RF Application with 70MHz IF and 520MHz LO
5578f
13
LT5578
TYPICAL APPLICATIONS
The measured room temperature performance is plotted
in Figure 10 for both low side and high side LO drive. At
2600MHz, the gain is approximately –2.8dB with a noise
figure of 11.2dB and OIP3 of about 22.2dBm. Low side
LO yields slightly better overall performance than high
side LO.
700 to 950 MHz Output Matching
The application shown on page 1 has a wider bandwidth
than the 740MHz and 900MHz configurations. Using two
additional components at the RF output allows the band32
10
30
SSB NF
GAIN (dB), NF (dB)
4
OIP3
26
24
22
2
OIP3 (dBm)
LS LO
HS LO
6
–10
c
–15
–20
a
20
0
GAIN
18
–2
–4
2200
0
–5
28
8
The swept gain, noise figure and OIP3 results are plotted
on page 1 for an IF of 140MHz and a low side LO. The
conversion gain is greater than 0.7dB across the band with
OIP3 better than 25.5dBm. The single side-band noise
figure is less than 8.8dB across the band.
RETURN LOSS (dB)
12
width to be extended to cover the range from 700MHz to
950MHz. Figure 11 compares the broadband return loss
to the typical 740MHz and 900MHz return loss performance.
2400
2300
2500
2600
RF OUTPUT FREQUENCY (MHz)
–25
600
700
16
2700
5578 F09
b
900
1000
800
FREQUENCY (MHz)
1100
5578 F11
Figure 11. Return Loss Comparison: 740MHz (a),
900MHz (b) and 700MHz to 950MHz (c)
Figure 10. Gain, Noise Figure and OIP3 vs RF Frequency
for the 2600MHz Application
Figure 12. LT5578 Evaluation Board (DC1545A)
5578f
14
LT5578
PACKAGE DESCRIPTION
UH Package
24-Lead Plastic QFN (5mm × 5mm)
(Reference LTC DWG # 05-08-1747 Rev A)
0.75 p0.05
5.40 p0.05
3.90 p0.05
3.20 p 0.05
3.25 REF
3.20 p 0.05
PACKAGE OUTLINE
0.30 p 0.05
0.65 BSC
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 p 0.10
R = 0.05
TYP
0.75 p 0.05
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
R = 0.150
TYP
23
PIN 1 NOTCH
R = 0.30 TYP
OR 0.35 s 45o
CHAMFER
24
0.55 p 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
5.00 p 0.10
3.25 REF
3.20 p 0.10
3.20 p 0.10
(UH24) QFN 0708 REV A
0.200 REF
NOTE:
1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
0.30 p 0.05
0.65 BSC
5578f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT5578
RELATED PARTS
PART NUMBER
Infrastructure
LT5514
DESCRIPTION
COMMENTS
Ultralow Distortion, IF Amplifier/ADC Driver
with Digitally Controlled Gain
40MHz to 900MHz Quadrature Demodulator
1.5GHz to 2.4GHz High Linearity Direct
Quadrature Modulator
850MHz Bandwidth, 47dBm OIP3 at 100MHz, 10.5dB to 33dB Gain Control Range
LT5519
0.7GHz to 1.4GHz High Linearity Upconverting
Mixer
17.1dBm IIP3 at 1GHz, Integrated RF Output Transformer with 50Ω Matching,
Single-Ended LO and RF Ports Operation
LT5520
1.3GHz to 2.3GHz High Linearity Upconverting
Mixer
LT5521
10MHz to 3700MHz High Linearity
Upconverting Mixer
400MHz to 2.7GHz High Signal Level
Downconverting Mixer
15.9dBm IIP3 at 1.9GHz, Integrated RF Output Transformer with 50Ω Matching,
Single-Ended LO and RF Ports Operation
24.2dBm IIP3 at 1.95GHz, NF = 12.5dB, 3.15V to 5.25V Supply, Single-Ended LO
Port Operation
LT5517
LT5518
LT5522
LT5526
LT5527
LT5528
High Linearity, Low Power Downconverting
Mixer
400MHz to 3.7GHz High Signal Level
Downconverting Mixer
1.5GHz to 2.4GHz High Linearity Direct
Quadrature Modulator
21dBm IIP3, Integrated LO Quadrature Generator
22.8dBm OIP3 at 2GHz, –158.2dBm/Hz Noise Floor, 50Ω Single-Ended RF and LO
Ports, 4-Channel W-CDMA ACPR = –64dBc at 2.14GHz
4.5V to 5.25V Supply, 25dBm IIP3 at 900MHz, NF = 12.5dB, 50Ω Single-Ended RF
and LO Ports
3V to 5.3V Supply, 16.5dBm IIP3, 100kHz to 2GHz RF, NF = 11dB, ICC = 28mA,
–65dBm LO-RF Leakage
IIP3 = 23.5dBm and NF = 12.5dBm at 1900MHz, 4.5V to 5.25V Supply, ICC = 78mA,
Conversion Gain = 2dB
21.8dBm OIP3 at 2GHz, –159.3dBm/Hz Noise Floor, 50Ω, 0.5VDC Baseband
Interface, 4-Channel W-CDMA ACPR = –66dBc at 2.14GHz
LT5557
400MHz to 3.8GHz 3.3V Downconverting Mixer IIP3 = 23.5dBm at 3.6GHz, NF = 15.4dB, Conversion Gain = 1.7dB, 3.3V Supply at
82mA, Single-Ended RF and LO Inputs
LT5558
600MHz to 1100MHz High Linearity Direct
22.4dBm OIP3 at 900MHz, –158dBm/Hz Noise Floor, 3kΩ, 2.1VDC Baseband
Quadrature Modulator
Interface, 3-Ch CDMA2000 ACPR = –70.4dBc at 900MHz
LT5560
Ultra-Low Power Active Mixer
10mA Supply Current, 10dBm IIP3, 10dB NF, Usable as Up- or Down-Converter.
LT5568
700MHz to 1050MHz High Linearity Direct
22.9dBm OIP3 at 850MHz, –160.3dBm/Hz Noise Floor, 50Ω, 0.5VDC Baseband
Quadrature Modulator
Interface, 3-Ch CDMA2000 ACPR = –71.4dBc at 850MHz
LT5572
1.5GHz to 2.5GHz High Linearity Direct
21.6dBm OIP3 at 2GHz, –158.6dBm/Hz Noise Floor, High-Ohmic 0.5VDC Baseband
Quadrature Modulator
Interface, 4-Ch W-CDMA ACPR = –67.7dBc at 2.14GHz
LT5575
700MHz to 2.7GHz Direct Conversion I/Q
Integrated Baluns, 28dBm IIP3, 13dBm P1dB, 0.03dB I/Q Amplitude Match,
Demodulator
0.4° Phase Match
LT5579
1.5GHz to 3.8GHz High Linearity Upconverting 27.3dBm OIP3 at 2.14GHz, NF = 9.9dB, 3.3V Supply, Single-Ended LO and RF Ports
Mixer
RF Power Detectors
LTC®5505
RF Power Detectors with >40dB Dynamic Range 300MHz to 3GHz, Temperature Compensated, 2.7V to 6V Supply
LTC5507
100kHz to 1000MHz RF Power Detector
100kHz to 1GHz, Temperature Compensated, 2.7V to 6V Supply
LTC5508
300MHz to 7GHz RF Power Detector
44dB Dynamic Range, Temperature Compensated, SC70 Package
LTC5509
300MHz to 3GHz RF Power Detector
36dB Dynamic Range, Low Power Consumption, SC70 Package
LTC5530
300MHz to 7GHz Precision RF Power Detector Precision VOUT Offset Control, Shutdown, Adjustable Gain
LTC5531
300MHz to 7GHz Precision RF Power Detector Precision VOUT Offset Control, Shutdown, Adjustable Offset
LTC5532
300MHz to 7GHz Precision RF Power Detector Precision VOUT Offset Control, Adjustable Gain and Offset
LT5534
50MHz to 3GHz Log RF Power Detector with
±1dB Output Variation over Temperature, 38ns Response Time, Log Linear
60dB Dynamic Range
Response
LTC5536
Precision 600MHz to 7GHz RF Power Detector 25ns Response Time, Comparator Reference Input, Latch Enable Input,
with Fast Comparator Output
–26dBm to +12dBm Input Range
LT5537
Wide Dynamic Range Log RF/IF Detector
Low Frequency to 1GHz, 83dB Log Linear Dynamic Range
LT5570
2.7GHz Mean-Squared Detector
±0.5dB Accuracy Over Temperature and >50dB Dynamic Range, Fast 500ns
Rise Time
LT5581
6GHz Low Power RMS Detector
40dB Dynamic Range, ±1dB Accuracy Over Temperature, 1.5mA Supply Current
5578f
16 Linear Technology Corporation
LT 0709 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2009