LT5554 - Broadband Ultra Low Distortion 7-Bit Digitally Controlled VGA

LT5554
Broadband Ultra Low
Distortion 7-Bit Digitally
Controlled VGA
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
1GHz Bandwidth at all Gains
48dBm OIP3 at 200MHz, 2VP-P into 50Ω,
ROUT = 100Ω
–88dBc IMD3 at 200MHz, 2VP-P into 50Ω,
ROUT = 100Ω
1.4nV/√Hz Input-Referred-Noise (RTI)
20dBm Output P1dB at 70MHz, ROUT = 130Ω
2dB to 18dB Gain Range (ROUT = 50Ω)
0.125dB Gain Step Size
30ps Group Delay Variation
5ns Fast Gain Settling Time
5ns Fast Overdrive Recovery
–80dB Reverse Isolation
The LT®5554 is a 7-bit digitally controlled programmable
gain (PG) amplifier with 16dB gain control range. It
consists of a 50Ω input variable attenuator, followed by
a high linearity variable transconductance amplifier. The
coarse 4dB input attenuator step is implemented via 2-bits
of digital control (PG5, PG6). The fine transconductance
amplifier 0.125dB step within 3.875dB gain control range
is set via 5-bits digital control (PG0 to PG4). The LT5554
gain control inputs (PGx) and the STROBE input can be
directly coupled to TTL or ECL drivers. The seven parallel
gain control inputs time skew can be eliminated by using
the STROBE input positive transition.
The internal output resistor RO = 400Ω limits the maximum overall gain to 36dB for open outputs. The internal
circuitry of open output collectors enables the LT5554 to
be unconditionally stable over any loading conditions (including external SAW filters) and provides –80dB reverse
isolation at 300MHz.
APPLICATIONS
n
n
n
n
n
Differential ADC Driver
IF Sampling Receivers
VGA IF Power Amplifier
50Ω Driver
Instrumentation
The LT5554 is internally protected during overdrive and
has an on-chip power supply regulator.
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
With 0.125dB step resolution and 5ns settling time, the
LT5554 is suitable in applications where continuous gain
control is required.
TYPICAL APPLICATION
OIP3 and SFDR vs Frequency
132
VCC
MODE
IF
BPF
RF
INPUT
DEC
IN–
LO
–
0.1μF
CDEC
0.1μF
LT5554
BPF
ADC
+
7 BITS
PGx GAIN CONTROL
130
46
OIP3
OIP3 (dBm)
IN+
SFDR (dBm/Hz)
0.1μF
IF
AMPLIFIER
49
ROUT = 50Ω
5V
128
43
5554 TA01
SFDR
STROBE
126
0
50
100
150
FREQUENCY (MHz)
40
200
5554 TA01b
5554f
1
LT5554
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Notes 1, 2)
GND
GND
PG4
GND
PG3
PG2
PG1
GND
TOP VIEW
Supply Voltage
VCC..........................................................................6V
Pin Voltages and Currents
OUT+, OUT– ............................................................7V
STROBE, PGx..........................................–0.5V to VCC
ENB, MODE.............................................–0.5V to VCC
IN+, IN–, DEC ........................................... –0.5V to 4V
Operating Ambient Temperature Range
LT5554 ............................................... –40°C to +85°C
Junction Temperature ........................................... 125°C
Storage Temperature Range................. –65°C to +150°C
32 31 30 29 28 27 26 25
GND
1
24 VCC
GND
2
23 ENB
DEC
3
22 GND
IN+
4
IN–
5
DEC
6
19 GND
GND
7
18 MODE
GND
8
17 VCC
21 OUT–
33
20 OUT+
GND
GND
STROBE
GND
PG0
PG6
PG5
GND
9 10 11 12 13 14 15 16
UH PACKAGE
32-LEAD (5mm s 5mm) PLASTIC QFN
TJMAX = 150°C, θJA = 34°C/W, θJC = 3°C/W
EXPOSED PAD (PIN 33) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT5554IUH#PBF
LT5554IUH#TRPBF
5554
32-Lead (5mm × 5mm) Plastic QFN
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
5554f
2
LT5554
AC ELECTRICAL CHARACTERISTICS
(ROUT = 50Ω) Specifications are at TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 2.2V, VIH = 2.2V, VIL = 0.6V, maximum gain (Notes 3, 6), (Test circuits shown in Figure 16), unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
Dynamic Performance
BW
Large Signal –3dB Bandwidth
All Gain Settings (Note 7)
LF – 1000
MHz
OP1dB
Output 1dB Compression Point
All Gain Settings, ROUT = 130Ω, 70MHz
20
dBm
GM
Amplifier Transconductance at GMAX
FIN = 100MHz
0.15
S
CMRR
Common Mode Gain to Single-Ended
Output
FIN = 100MHz, Figure 19
–6
dB
S12
Reverse Isolation
FIN = 100MHz
FIN = 400MHz
–86
–78
dB
dB
Overdrive Recovery Time
5ns Input Pulse, VOUT within ±10%
5
ns
Noise/Linearity Performance Two Tones, POUT = 4dBm/Tone (2VP-P into 50Ω), Δf = 200kHz
IIP3
Input Third Order Intercept Point
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
27
30
dBm
dBm
OIP3
Output Third Order Intercept Point for
Max-Gain
FIN = 100MHz
FIN = 200MHz
45
46
dBm
dBm
IMD3
Intermodulation Product for Max-Gain
FIN = 100MHz
FIN = 200MHz
–82
–84
dBc
dBc
OIP3
Output Third Order Intercept Point for
–3.875dB STEP
FIN = 100MHz
FIN = 200MHz
44
40
dBm
dBm
OIP3
Output Third Order Intercept Point
GMAX, F1 = 88MHz, F2 = 112MHz
GMAX –3.875dB, F1 = 88MHz, F2 = 112MHz
47
44
dBm
dBm
HD3
Third Harmonic Distortion
Pout = 10dBm, FIN = 100MHz, GMAX
–62
dBc
VONOISE
Output Noise Noise Spectral Density
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
10.7
7.3
nV/√Hz
nV/√Hz
NF
Noise Figure
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
10
10.5
dB
dB
RTI
Input Referred Noise Spectral Density
(RMS) (Note 5)
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
1.34
1.42
nV/√Hz
nV/√Hz
SFDR
Spurious Free Dynamic Range in 1Hz
BW.
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
128
129
dBm/Hz
dBm/Hz
40.5
38
Amplifier Voltage Gain and Gain Step
GMAX
Maximum Voltage and Power Gain
FIN = 112MHz
15.3
17.6
19.7
dB
GMIN
Minimum Voltage and Power Gain
FIN = 100MHz
1.725
GSTEP
Gain Step Size (Note 9)
Except For –4dB, –8dB, –12dB Steps
For –4dB, –8dB, –12dB Steps
0.125
0.25
0.35
dB
dB
GDERROR
Group Delay Step Accuracy
FIN = 100MHz
10
ps
43
47
Ω
Ω
dB
AMPLIFIER I/O Differential IMPEDANCE
RIN
Input Resistance
FIN = 100MHz, GMAX to GMAX –3.875dB
FIN = 100MHz, GMAX –4dB to GMIN
CIN
Input Capacitance
FIN = 100MHz
2.8
pF
RO
Output Resistance
FIN = 100MHz
400
Ω
CO
Output Capacitance
FIN = 100MHz
1.9
pF
5554f
3
LT5554
AC ELECTRICAL CHARACTERISTICS
(ROUT = 100Ω) Specifications are at TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 2.2V, VIH = 2.2V, VIL = 0.6V, maximum gain (Notes 3, 8), (Test circuits shown in Figure 16), unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
Noise/Linearity Performance Two Tones, POUT = 4dBm/Tone (2VP-P into 50Ω), Δf = 200kHz
IIP3
Input Third Order Intercept Point
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
27
27
dBm
dBm
OIP3
Output Third Order Intercept Point for
Max-Gain
FIN = 100MHz
FIN = 200MHz
48
48
dBm
dBm
IMD3
Intermodulation Product for Max-Gain
FIN = 100MHz
FIN = 200MHz
–88
–88
dBc
dBc
VONOISE
Output Noise Noise Spectral Density
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
21.4
14.5
nV/√Hz
nV/√Hz
NF
Noise Figure
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
10
10.5
dB
dB
RTI
Input Referred Noise Spectral Density
(RMS) (Note 5)
GMAX, FIN = 200MHz
GMAX –3.875dB, FIN = 200MHz
1.34
1.42
nV/√Hz
nV/√Hz
SFDR
Spurious Free Dynamic Range in
1Hz BW.
GMAX, FIN = 200MHz
128
dBm/Hz
GVMAX
Maximum Voltage Gain
FIN = 100MHz
23.6
dB
GPMAX
Maximum Power Gain
FIN = 100MHz
20.6
dB
AC ELECTRICAL CHARACTERISTICS (Timing Diagram)
(ROUT = 50Ω) Specifications are
at TA = 25°C. VCC = 5V, VCCO = 5V, ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V, maximum gain (Test circuit shown in
Figure 16), unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
PGx and Strobe Timing Characteristics
TSU
Setup Time PGx vs STROBE
0
ns
THOLD
Hold Time PGx vs STROBE
1
ns
TPW
STROBE Pulse Width
2
ns
TR
STROBE Period
4
ns
TLATENCY
Latency Time of the Previous Gain State
Output Settles within 1%
4
ns
TGLITCH
Time Between Previous Stable Gain State
to Next Stable State
Output Settles within 1%
5
ns
AGLITCH
Max Glitch Amplitude
VIN = 0 (No Signal or STROBE Transition During
Output Signal Zero Crossing)
1
mV
STROBE Transition when Output Power is at
Peak + 10dBm Power
3
dB
5554f
4
LT5554
AC ELECTRICAL CHARACTERISTICS (Timing Diagram)
Timing Diagram
PG0, 1, 2, 3, 4, 5, 6
INPUTS
TSU
THOLD
STROBE
INPUTS
DATA
TRANSPARENT
TPW
DATA
LATCH
TGLITCH
TLATENCY
OUT SIGNAL
STATE (i)
STATE (i + 1)
STATE (i + 2)
5554 TD01
DC ELECTRICAL CHARACTERISTICS
Specifications are at TA = 25°C. VCC = 5V, VCCO = 5V, ENB = 3V,
MODE = 5V, unless otherwise noted. (Note 3) (Test circuit shown in Figure 16), unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
4.75
5
5.25
V
5
6
V
2
2.15
Normal Operating Conditions
VCC
Supply Voltage
VCCO
OUT+, OUT– Output Pin DC Common Mode
(Note 4)
Voltage
Shutdown DC Characteristics, ENB = 0.6V
VIN(BIAS)
DEC, IN+, IN– Bias Voltage
IIL(PG)
PGx, STR Input Current
VIN = 0.6V
IIH(PG)
PGx, STR Input Current
VIN = 5V
IOUT
OUT+, OUT– Current
ICC
VCC Supply Current
V
0
μA
210
μA
4
20
μA
5.1
mA
0.6
V
VCC
V
20
μA
Enable Input DC Characteristics
VIL(EN)
ENB Input LOW Voltage
Disable
VIH(EN)
ENB Input HIGH Voltage
Enable
3
IIL(EN)
ENB Input Current
VIN = 0.6V
IIH(EN)
ENB Input Current
VIN = 3V
70
IIH(EN)
ENB Input Current
VIN = 5V
220
μA
300
μA
5554f
5
LT5554
DC ELECTRICAL CHARACTERISTICS
Specifications are at TA = 25°C. VCC = 5V, VCCO = 5V, ENB = 3V,
MODE = 5V, unless otherwise noted. (Note 3) (Test circuit shown in Figure 16), unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
DEC External Capacitor Charge/Discharge CURRENT
IIH(DEC)
DEC Pin Source Current
VDEC = 4V
27
50
70
mA
IIL(DEC)
DEC Pin Sink Current
VDEC = 1.8V
–70
–38
–14
mA
0.6
V
2.3
V
Mode Input Three-State DC Characteristics
VIL(MODE)
MODE Input LOW Voltage for AC-Couple
PGx AC-Coupled, STROBE AC-Coupled
0
VOPEN(MODE)
MODE Input OPEN
PGx AC-Coupled, STROBE DC-Coupled
1.7
OPEN
VIH(MODE)
MODE Input HIGH Voltage
PGx DC-Coupled, STROBE DC-Coupled
VCC – 0.4
VCC
IIL(MODE)
MODE Input Current
VMODE = 0V
–42
–31
–23
μA
V
IIH(MODE)
MODE Input Current
VMODE = 5V
43
72
100
μA
0.6
V
30
μA
220
μA
4.6
V
PGx (MODE = VCC) and STROBE (MODE = OPEN or MODE = VCC) INPUTS for DC-Coupled
VIL
Input LOW Voltage
VIH
Input HIGH Voltage
IIL(DC)
Input Current
VIN = 0.6V
IIH(DC)
Input Current
VIN = 5V
2.2
125
V
170
PGx (MODE = 0V or MODE = OPEN) and STROBE (MODE = 0V) INPUTS for AC-Coupled
VIN(AC)
Input Pulse Range
Instantaneous Input Voltage
0
VIN(AC)P-P
Input Pulse Amplitude
Rise and Fall Time <5ns
Rise and Fall Time >80ns
VIN(AC)MAX
Maximum Input Noise Amplitude
No LT5554 Gain Update
IIL(AC)
Input Current
VIN = 0V
–210
–155
–100
μA
IIH(AC)
Input Current
VIN = 5V
310
420
530
μA
V
600
300
mVP-P
mVP-P
100
mVP-P
Amplifier DC Characteristics
VIN(DEC)
DEC
GMAX
1.85
2
2.25
VIN(BIAS)
IN+, IN– Bias Voltage
GMAX
1.8
2.04
2.2
RIN
INPUT Differential Resistance
GMAX
GMIN
GM
Amplifier Transconductance
GMAX
IODC
OUT+, OUT– Quiescent Current
VOUT = 5V
IOUT(OFFSET)
Output Current Mismatch
IN+, IN– Open
ICC
VCC Supply Current
GMAX, MODE = 0V
GMIN, MODE = 0V
GMAX, MODE = 5V
GMIN, MODE = 5V
ICC(TOTAL)
Total Supply Current
ICC + 2 • IODC (GMAX)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to GND ground.
Note 3: RS = RIN = 50Ω Input matching is assumed. PIN is the available
input power. POUT is the power into ROUT. ROUT = RO || RLOAD is the total
output resistance at amplifier open-collectors outputs (used in GV, GP gain
calculation). RO = 400Ω is LT5554 internal output impedance. RLOAD is
48
50
0.15
33
47
78
77
75
75
110
109
106
106
S
57
mA
132
131
127
127
mA
mA
mA
mA
200
200
V
Ω
Ω
μA
mA
load resistance as seen at OUT+, OUT– pins.
All dBm figures are with respect to 50Ω. Specifications refer to differential
inputs and differential outputs.
Note 4: An external power supply equal to VCCO is used for choke
inductors or center-tap transformer output interfaces. Whenever OUT+,
OUT– pins are biased via resistors, the voltage drop produced by the DCoutput current (IODC = 45mA typical) may require a larger output external
power supply. However, care must be taken not to exceed the OUT+,
OUT– absolute maximum rating when the LT5554 is disabled.
5554f
6
LT5554
ELECTRICAL CHARACTERISTICS
Note 5: RTI (Referred-To-Input) stands for the total input-referred noise
voltage source. RTI is close to output noise voltage divided by voltage gain
(the exact equation is given in Definition of Specification section). The
equivalent noise source eN is twice the RTI value.
Note 6: The external loading at LT5554 OUT+/OUT– pins is RLOAD = 57Ω.
ROUT = RLOAD || RO = 50Ω.
Note 7: The IN+, IN–, DEC pins are internally biased. The time-constant
of input coupling capacitor sets the low frequency corner (LF) at input.
The output coupling capacitors or the transformer sets the low frequency
corner (LF) at the output. The LT5554 operates internally down to DC.
Note 8: The external loading at OUT+/OUT– pins is RLOAD = 133Ω.
ROUT = RLOAD || RO = 100Ω.
Note 9: Depending on the actual input matching conditions and frequency
of operation, the LT5554 steps involving the input attenuator tap change
may show less than 0.125dB change. These steps are GMAX –4dB, GMAX
–8dB, GMAX –12dB, and the code is given in the Programmable Gain Table.
The LT5554 monotonic operation for 0.125dB step resolution can still be
obtained by skipping any such code with a gain error excedding 0.125dB.
TYPICAL PERFORMANCE CHARACTERISTICS
(ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure 16), unless otherwise noted.
Gain vs Frequency for
0.5dB Steps, Figure 17
Differential Gain Error vs
Frequency at –40°C
20
Differential Gain Error vs
Frequency at 85°C
0.3
0.3
0.2
0.2
18
16
12dB
12
10
8
6
12dB
0.1
GAIN ERROR (dB)
GAIN ERROR (dB)
GAIN (dB)
14
4dB
8dB
0
–0.1
4
0.1
4dB
8dB
0
–0.1
2
0
–0.2
0 100 200 300 400 500 600 700 800 900 1000
FREQUENCY (MHz)
50
75
100
125
150
FREQUENCY (MHz)
5554 G01
–0.1
–0.2
0.3
0.1
0
–0.1
0
–4
–8
–12
ATTENUATION (dB)
–16
5554 G04
100
125
150
FREQUENCY (MHz)
–0.2
175
200
–40°C
25°C
85°C
0.2
GAIN ERROR (dB)
0
75
Differential Gain Error vs
Attenuation at 200MHz
–40°C
25°C
85°C
0.2
GAIN ERROR (dB)
GAIN ERROR (dB)
0.3
0.1
50
5554 G03
Differential Gain Error vs
Attenuation at 100MHz
–40°C
25°C
85°C
0.2
–0.2
200
5554 G02
Differential Gain Error vs
Attenuation at 50MHz
0.3
175
0.1
0
–0.1
0
–4
–8
–12
ATTENUATION (dB)
–16
5554 G05
–0.2
0
–4
–8
–12
ATTENUATION (dB)
–16
5554 G06
5554f
7
LT5554
TYPICAL PERFORMANCE CHARACTERISTICS
(ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure 16), unless otherwise noted.
Integral Gain Error vs
Attenuation at 50MHz
0.2
0.1
0.1
0.1
–4
–8
–12
ATTENUATION (dB)
–0.1
–16
0
0
–4
–8
–12
ATTENUATION (dB)
5554 G07
24
200MHz
17.4
17.2
–20
0
20
40
60
TEMPERATURE (°C)
–8
–12
ATTENUATION (dB)
–16
8
0
8
0
–8
–16
–35
80
70MHz
140MHz
200MHz
16
–8
17.0
–40
–4
POUT vs PIN at GMAX – 3.875dB
24
POUT (dBm)
POUT (dBm)
100MHz
0
5554 G09
70MHz
140MHz
200MHz
16
50MHz
17.6
–0.1
POUT vs PIN at Maximum Gain
Maximum Gain vs Temperature
17.8
–16
5554 G08
18.0
GMAX (dB)
0.2
0
0
–40°C
25°C
85°C
0.3
0.2
0
–0.1
0.4
–40°C
25°C
85°C
0.3
GAIN ERROR (dB)
0.3
GAIN ERROR (dB)
0.4
–40°C
25°C
85°C
Integral Gain Error vs
Attenuation at 200MHz
GAIN ERROR (dB)
0.4
Integral Gain Error vs
Attenuation at 100MHz
–25
–15
–5
PIN (dBm)
5
5554 G10
–16
–35
15
–25
–15
–5
PIN (dBm)
5554 G11
5
15
5554 G12
(ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V, ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure
16) POUT = 4dBm/tone (2VP-P into 50Ω), Δf = 200kHz, unless otherwise noted.
Two-Tone OIP3 vs Frequency at
Max Gain, Three Temperatures
Two-Tone IMD3 vs Frequency at
Max Gain, Three Temperatures
49
IIP3 vs Frequency at Max Gain,
Three Temperatures
–76
32
85°C
85°C
–79
30
IMD3 (dBc)
OIP3 (dBm)
–40°C
25°C
–40°C
IIP3 (dBm)
25°C
46
–82
25°C
28
–40°C
43
–85
26
85°C
40
0
50
100
150
FREQUENCY (MHz)
200
5554 G13
–88
0
50
100
150
FREQUENCY (MHz)
200
5554 G14
24
0
50
100
150
FREQUENCY (MHz)
200
5554 G15
5554f
8
LT5554
TYPICAL PERFORMANCE CHARACTERISTICS
(ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure 16) POUT = 4dBm/tone (2VP-P into 50Ω),
Δf = 200kHz, unless otherwise noted.
Two-Tone OIP3 vs Frequency for
GMAX and Critical Gain Steps
Two-Tone IMD3 vs Frequency for
GMAX and Critical Gain Steps
49
IIP3 vs Frequency for GMAX and
GMAX –3.875dB
32
–70
GMAX – 3.875dB
GMAX – 12dB
–76
IMD3 (dBc)
OIP3 (dBm)
GMAX
GMAX – 15.875dB
43
GMAX – 3.875dB
–82
GMAX – 3.875dB
IIP3 (dBm)
46
30
GMAX – 15.875dB
GMAX
GMAX
28
26
GMAX – 12dB
200
100
150
FREQUENCY (MHz)
–88
24
50
200
100
150
FREQUENCY (MHz)
5554 G16
50
100
150
FREQUENCY (MHz)
200
5554 G18
5554 G17
Two-Tone IMD3 and OIP3 vs
Attenuation at 50MHz
Two-Tone IMD3 and OIP3 vs
Attenuation at 70MHz
–70
48
–70
–74
46
–74
46
–78
44
–78
44
48
OIP3
IMD3
IMD3
–82
–86
0
–4
–8
–12
ATTENUATION (dB)
42
–82
40
–16
–86
OIP3 (dBm)
OIP3 (dBm)
IMD3 (dBc)
OIP3
IMD3 (dBc)
42
0
–4
–8
–12
ATTENUATION (dB)
5554 G19
40
–16
5554 G20
Two-Tone IMD3 and OIP3 vs
Attenuation at 100MHz
Two-Tone IMD3 and OIP3 vs
Attenuation at 140MHz
–70
48
–70
48
OIP3
–74
46
OIP3
–82
42
–74
46
–78
44
–82
42
IMD3
–86
0
–4
–8
–12
ATTENUATION (dB)
OIP3 (dBm)
44
OIP3 (dBm)
–78
IMD3 (dBc)
50
IMD3 (dBc)
40
IMD3
40
–16
5554 G21
–86
0
–4
–8
–12
ATTENUATION (dB)
40
–16
5554 G22
5554f
9
LT5554
TYPICAL PERFORMANCE CHARACTERISTICS
(ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure 16) POUT = 4dBm/tone (2VP-P into 50Ω),
Δf = 200kHz, unless otherwise noted.
Two-Tone IMD3 and OIP3 vs
Attenuation at 200MHz
Two-Tone OIP3 vs Tone Power at
Max-Gain
–70
48
Two-Tone OIP3 vs Tone Power at
Min-Gain
47
47
44
44
IMD3
44
OIP3 (dBm)
–78
OIP3
50MHz
70MHz
100MHz
140MHz
200MHz
42
0
–4
40
–16
–8
–12
ATTENUATION (dB)
38
50MHz
70MHz
100MHz
140MHz
200MHz
41
41
–82
–86
OIP3 (dBm)
46
OIP3 (dBm)
IMD3 (dBc)
–74
0
38
6
9
3
OUTPUT TONE POWER (dBm)
5554 G23
12
0
3
6
9
OUTPUT TONE POWER (dBm)
5554 G25
5554 G24
Two-Tone OIP3 vs ROUT, for GMAX
Two-Tone OIP3 vs VCCO, for GMAX
–3.875dB
Two-Tone OIP3 vs VCCO, for GMAX
50
12
48
48
45
45
OIP3 (dBm)
OIP3 (dBm)
OIP3 (dBm)
48
42
42
46
44
25MHz
70MHz
140MHz
200MHz
50
75
ROUT (Ω)
100
39
36
2
3
4
5
OUTPUT COMMON MODE VOLTAGE (V)
6
36
25MHz
70MHz
140MHz
200MHz
2
3
4
5
OUTPUT COMMON MODE VOLTAGE (V)
5554 G28
5554 G52
Harmonic Distortion vs
Attenuation, 50MHz,
POUT = 10dBm, Figure 17
6
5554 G30
OIP3 vs Frequency for GMAX and
GMIN, POUT = 10dBm
50
–70
–75
–80
45
HD3
–85
OIP3 (dBm)
HARMONIC DISTORTION (dBc)
39
25MHz
70MHz
140MHz
200MHz
–90
GMIN
40
–95
GMAX
–100
HD5
–105
35
0
–4
–8
–12
ATTENUATION (dB)
–16
5554 G27
50
100
150
FREQUENCY (MHz)
200
5554 G29
5554f
10
LT5554
TYPICAL PERFORMANCE CHARACTERISTICS
(ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure 16) POUT = 4dBm/tone (2VP-P into 50Ω),
Δf = 200kHz, unless otherwise noted.
HD3 vs Frequency for GMAX and
GMIN, POUT = 10dBm, Figure 17
HD5 vs Frequency for GMAX and
GMIN, POUT = 10dBm, Figure 17
–70
–56
HARMONIC DISTORTION (dBc)
HARMONIC DISTORTION (dBc)
–50
GMAX
–62
GMIN
–68
–74
–80
50
100
150
FREQUENCY (MHz)
–76
–82
GMIN
–88
–94
–100
200
GMAX
50
100
150
FREQUENCY (MHz)
200
5554 G31
5554 G32
(ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V, ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure 16),
maximum gain, unless otherwise noted.
HD3 and HD5 vs POUT
for GMAX, Figure 17
–40
–50
20
15
HD3
HD5
–60
NF (dB)
–55
15
GMAX –3.875
GMAX –3.875
HD3
NF (dB)
HARMONIC DISTORTION (dBc)
20
70MHz
140MHz
–45
Single-Ended Output NF vs
Frequency, Figure 18
Noise Figure vs Frequency
GMAX
10
GMAX
10
–65
–70
5
–75
–80
5
HD5
7
10
13
OUTPUT POWER (dBm)
0
16
0
200
400
600
FREQUENCY (MHz)
5554 G33
0
800
0
200
400
600
FREQUENCY (MHz)
5554 G34
Noise Figure vs Attenuation,
140MHz
5554 G35
Input Referred Noise vs
Attenuation, 140MHz
25
800
Output Noise Density vs
Attenuation, 140MHz
6
12
20
15
10
VONOISE (nV/√Hz)
RTI (nV/√Hz)
NF (dB)
9
4
2
3
5
0
6
0
–4
–8
–12
ATTENUATION (dB)
–16
5554 G36
0
0
–4
–8
–12
ATTENUATION (dB)
–16
5554 G37
0
0
–4
–8
–12
ATTENUATION (dB)
–16
5554 G38
5554f
11
LT5554
TYPICAL PERFORMANCE CHARACTERISTICS
( ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure 16), maximum gain, unless otherwise noted.
Single-Ended Output Current vs
Attenuation
Total ICC Current vs Attenuation
98
215
85°C
208
96
CURRENT (mA)
CURRENT (mA)
–40°C
25°C
85°C
94
25°C
200
193
92
0
–4
–8
–12
ATTENUATION (dB)
185
–16
–40°C
0
–4
–8
–12
ATTENUATION (dB)
5554 G39
–16
5554 G40
ICC Shutdown Current vs VCC,
ENB = 0.6V
VIN(BIAS) vs Attenuation
5
2.2
85°C
4
VIN(BIAS) (V)
CURRENT (mA)
–40°C
3
25°C
2
–40°C
2.1
85°C
25°C
1
0
4.7
4.9
5.1
VCC (V)
5.3
5.5
5554 G41
2.0
0
–4
–8
–12
ATTENUATION (dB)
–16
5554 G42
5554f
12
LT5554
TYPICAL PERFORMANCE CHARACTERISTICS
(ROUT = 50Ω) TA = 25°C. VCC = 5V, VCCO = 5V,
ENB = 3V, MODE = 5V, STROBE = 3V, VIH = 2.2V, VIL = 0.6V (Test circuit shown in Figure 16), maximum gain, unless otherwise noted.
2dB-Step Response (PG4)
120MHz Signal
8dB-Step Response (PG6)
120MHz Signal
0.1V/DIV
8dB-Step Response (PG6)
120MHz Pulse Signal
0.1V/DIV
10ns/DIV
0.2V/DIV
5554 G46
10ns/DIV
5554 G47
5ns/DIV
MODE = HIGH
MODE = HIGH
MODE = HIGH
8dB-Step (PG6) 120MHz Pulse
Signal for 8dB Overdrive
8dB-Step (PG6) 120MHz
Sinusoidal Signal for 2dB
Overdrive
8dB-Step (PG6) 120MHz
Sinusoidal Signal for 8dB
Overdrive
1V/DIV
1V/DIV
5ns/DIV
MODE = HIGH
5554 G48
1V/DIV
5554 G49
5ns/DIV
MODE = HIGH
5554 G50
10ns/DIV
5554 G51
MODE = HIGH
PIN FUNCTIONS
GND (Pins 1, 2, 7, 8, 10, 13, 15, 16, 19, 22, 25, 26, 28,
31): Ground Pins.
DEC (Pins 3, 6): Decoupling Pin for the Internal DC Bias
Voltage for the Differential Inputs, IN+ and IN–. It is also
connected to the ‘virtual ground’ of the input resistive
attenuator. Capacitive de-coupling to ground is recommended in order to preserve linearity performance when
IN+, IN– inputs are driven with up to 3dB imbalance.
IN+ (Pin 4): Positive Signal Input Pin with Internal DC
Bias to 2V.
IN– (Pin 5): Negative Signal Input Pin with Internal DC
Bias to 2V.
PG5 (Pin 9): 4dB Step Amplifier Programmable Gain Control Input Pin. Input levels are controlled by MODE pin.
PG6 (Pin 11): 8dB Step Amplifier Programmable Gain
Control Input Pin. Input levels are controlled by the
MODE pin.
PG0 (Pin 12): 0.125dB Step Amplifier Programmable
Gain Control Input Pin. Input levels are controlled by
MODE pin.
STROBE (Pin 14): Strobe Pin for the Programmable Gain
Control Inputs (PGx). With STROBE in Low-state, the
Amplifier Gain is not changed by PGx state changes (latch
mode). With STROBE in High-state, the Amplifier Gain is
asynchronously set by PGx inputs transitions (transparent-mode). A positive STROBE transition updates the
PGx state. Low-state and High-state depends on MODE
pin level (Table1).
VCC (Pins 17, 24): Power Supply Pins. These pins are
internally connected together.
MODE (Pin 18): PGx and STROBE Functionality and Level
Control Pin. When MODE is higher than VCC – 0.4V, the
PGx and STROBE are DC-coupled. When the MODE pin
is lower than 0.6V, the PGx and STROBE are AC-coupled.
5554f
13
LT5554
PIN FUNCTIONS
When the MODE pin is left open, the PGx inputs are ACcouple and the STROBE input is DC-coupled.
When the ENB input voltage is less than or equal to 0.6V,
the amplifier is turned off.
In DC-coupled mode, the PGx and STROBE inputs levels are
0.6V and 2.2V. In AC-coupled mode, the PGx and STROBE
inputs are driven with 0.6VP-P minimum amplitude (with
rise and fall time <5ns) regardless the DC voltage level. A
positive transition sets a High-state. A negative transition
sets a Low-state (for PGx and STROBE inputs).
PG4 (Pin 27): 2dB Step Amplifier Programmable Gain Control Input Pin. Input levels are controlled by MODE pin.
PG3 (Pin 29): 1dB Step Amplifier Programmable Gain Control Input Pin. Input levels are controlled by MODE pin.
PG2 (Pin 30): 0.5dB Step Amplifier Programmable Gain Control Input Pin. Input levels are controlled by MODE pin.
OUT+ (Pin 20): Positive Amplifier Output Pin. A transformer
with a center tap tied to VCC or a choke inductor is recommended to conduct the DC quiescent current.
PG1 (Pin 32): 0.25dB Step Amplifier Programmable
Gain Control Input Pin. Input levels are controlled by
MODE pin.
OUT– (Pin 21): Negative Amplifier Output Pin. A transformer
with a center tap tied to VCC or a choke inductor is recommended to conduct the DC quiescent current.
EXPOSED PAD (Pin 33): Ground. This pin must be soldered to the printed circuit board ground plane for good
heat dissipation.
ENB (Pin 23): Enable Pin for Amplifier. When the ENB
input voltage is higher than 3V, the amplifier is turned on.
BLOCK DIAGRAM
GND
(15 PINS)
17
VCC
VCC
24
ENB
VOLTAGE
REGULATOR
AND BIAS
23
ENABLE
CONTROL
DEC
3
RIN+
25Ω
ATTENUATOR
IN+
OUT–
4
21
RO
400Ω
AMPLIFIER
IN–
OUT+
20
5
RIN–
25Ω
DEC
6
ATTENUATOR
GAIN LOGIC
4dB STEPS
12dB RANGE
PG6
11
PG5
9
TRANSCONDUCTANCE
GAIN LOGIC
0.125dB STEPS
3.875dB RANGE
MODE
STROBE
LOGIC
MODE
18
STROBE
14
PG4
27
PG3
29
PG2
30
PG1
32
PG0
12
5554 BD
Figure 1. Functional Block Diagram
5554f
14
LT5554
FUNCTIONAL CHARACTERISTICS
Programmable Gain Table
STATE
PG0
PG1
PG2
N
PG3
PG4
PG5
PG6
Step Size in dB
0.125
0.25
0.5
1
ATTENUATION
Step Relative to Max Gain
GAIN STATE NAME
dB
2
4
8
(N – 127) • 0.125dB
127
H
H
H
H
H
H
H
0.00dB
GMAX (Max Gain)
126
L
H
H
H
H
H
H
–0.125dB
GMAX –0.125dB
125
H
L
H
H
H
H
H
–0.250dB
GMAX –0.25dB
124
L
L
H
H
H
H
H
–0.375dB
GMAX –0.375dB
123
H
H
L
H
H
H
H
–0.500dB
GMAX –0.5dB
122
L
H
L
H
H
H
H
–0.625dB
GMAX –0.625dB
121
H
L
L
H
H
H
H
–0.750dB
GMAX –0.75dB
120
L
L
L
H
H
H
H
–0.875dB
119
H
H
H
L
H
H
H
–1.00dB
GMAX –1dB
118
L
H
H
L
H
H
H
–1.125dB
GMAX –1.125dB
112
L
L
L
L
H
H
H
–1.875dB
GMAX –1.875dB
111
H
H
H
H
L
H
H
–2.00dB
GMAX –2dB
104
L
L
L
H
L
H
H
–2.875dB
GMAX –2.875dB
103
H
H
H
L
L
H
H
–3.00dB
GMAX –3dB
96
L
L
L
L
L
H
H
–3.875dB
GMAX –3.875dB
95
H
H
H
H
H
L
H
–4.00dB
GMAX –4dB
…
…
…
…
64
L
L
L
L
L
L
H
–7.875dB
GMAX –7.875dB
63
H
H
H
H
H
H
L
–8.00dB
GMAX –8dB
…
32
L
L
L
L
L
H
L
–11.875dB
GMAX –11.875dB
31
H
H
H
H
H
L
L
–12.000dB
GMAX –12dB
…
8
L
L
L
H
L
L
L
–14.875dB
GMAX –14.875dB
7
H
H
H
L
L
L
L
–15.000dB
GMAX –15dB
6
L
H
H
L
L
L
L
–15.125dB
GMAX –15.125dB
5
H
L
H
L
L
L
L
–15.250dB
GMAX –15.25dB
4
L
L
H
L
L
L
L
–15.375dB
GMAX –15.375dB
3
H
H
L
L
L
L
L
–15.500dB
GMAX –15.5dB
2
L
H
L
L
L
L
L
–15.625dB
GMAX –15.625dB
1
H
L
L
L
L
L
L
–15.750dB
GMAX –15.75dB
0
L
L
L
L
L
L
L
–15.875dB
GMIN (Min Gain)
5554f
15
LT5554
DEFINITION OF SPECIFICATIONS
Amplifier Impedance and Gain Definitions
(Differential)
RS
GV
GP
RIN
LT5554 input resistance (internal, 50Ω)
CIN
LT5554 input capacitance (internal)
RO
LT5554 output resistance (internal, 400Ω)
CO
LT5554 output capacitance (internal)
RLOAD
Load resistance as seen by LT5554
output pins
CLOAD
Load capacitance as seen by LT5554
output pins
ROUT
Total output resistance at LT5554 open-collectors outputs (used in GV, GP gain calculation):
PIN
VIN is peak - value
POUT
Total output capacitance at LT5554 output
(used in gain calculation):
Total power delivered by LT5554 open-collector outputs:
⎛ ⎛ V 2⎞ ⎞
OUT
⎜ ⎜
⎟ ⎟
⎜ ⎝ 2 ⎠ ⎟
POUT = 10 log ⎜
in dBm,
ROUT • 1mW ) ⎟
(
⎜
⎟
⎜⎝
⎠⎟
LT5554 differential transconductance:
GM =
Power available at LT5554 input, RS = RIN =
50Ω input matching:
⎛ ⎛ V 2⎞ ⎞
IN
⎜ ⎜
⎟ ⎟
⎜ ⎝ 2 ⎠ ⎟
PIN = 10 log ⎜
in dBm,
RIN • 1mW ) ⎟
(
⎟
⎜
⎟⎠
⎜⎝
COUT = CLOAD + CO
GM
LT5554 differential power gain:
GP = 10log(RIN • GM2 • ROUT) in dB
ROUT = RO || RLOAD
COUT
⎛V ⎞
GV = 20 log ⎜ OUT ⎟ = 20 log (GM • ROUT ) in dB
⎝ VIN ⎠
Input source resistor. Input matching is assumed:
RS = RIN
LT5554 differential voltage gain:
IOUT
VIN
VOUT is peak - value
INTERNAL
EXTERNAL
OUT+
IOUT = GM • VIN
IDC
CO
1.9pF
RO
400Ω
ROUT
RLOAD
RO
400Ω
OUT–
CLOAD VOUT = IOUT • ROUT
5554 F02
RLOAD
ROUT
Figure 2. Output Equivalent Circuit and Impedance Definitions
5554f
16
LT5554
DEFINITION OF SPECIFICATIONS
NF
Noise Definitions for 50Ω Matched Input
eRS
Source resistor RMS noise voltage:
(
⎛
eN2 + iN2 • RS2
NF = 10 log ⎜ 1+
⎜
eRS2
⎝
eRS2 = 4 • k • T • RS ; for RS = 50Ω,
eRS =
Noise figure in dB according to any of the following equations:
0.9nV
Hz
) ⎞⎟ =
⎟
⎠
⎞
⎛
⎟
⎜
⎛ 1+ V
1+ RTI2 ⎟
N
⎜
10 log ⎜
= 10 log
2 ⎟
⎜ ⎛ e ⎞2⎟
⎝ eRS ⎠
⎜ ⎜ RS ⎟ ⎟
⎝⎝ 2 ⎠ ⎠
2⎞
eN
Equivalent short-circuit input RMS noise voltage
source
iN
Equivalent open-circuit input RMS noise current
source
vN
Equivalent total input RMS noise voltage
source:
Linearity Definitions for 50Ω Matched Input
vN2 = eN2 + iN2 • RS2 (RS = 50Ω)
IMD3[dBc]
Third-order intermodulation product
(negative value)
IIP3[dBm]
IIP3 = PIN (per-tone) –
RTI
Referred-to-input LT5554 noise voltage:
2
RTI =
2
2
2
(eRS + eN + iN • RS )
2
=
vN
2
VONOISE LT5554 output noise voltage:
⎛ ⎞
2
⎛
⎜⎝ 20 ⎟⎠
⎛ eRS ⎞ ⎞
2
⎜ RTI + ⎜
⎟ • 10
⎟
⎜⎝
⎝ 2 ⎠ ⎟⎠
⎛ 2⎞
SFDR[dBm/Hz] SFDR = ⎜ ⎟ • (174 + IIP3 – NF )
⎝ 3⎠
GV
VONOISE =
IMD3
2
OIP3[dBm]
OIP3 = POUT –
IMD3
= IIP3 + GP
2
APPLICATIONS INFORMATION
Circuit Operation
The LT5554 is a high dynamic range programmable-gain
amplifier. It consists of the following sections:
• An input variable attenuator with 50Ω input impedance (four 4dB steps, controlled by PG5, PG6 inputs)
• A differential programmable transconductance amplifier (32 steps, 0.125dB each controlled by PG0, PG1,
PG2, PG3, PG4 inputs)
• Programmable logic blocks
• Internal bias (voltage regulators)
• Enable/disable circuit
Since no internal feedback network is used between amplifier outputs and inputs, the LT5554 is able to offer:
• Unconditional stability for I/O reactive loading such
as filters (no isolation output resistors required)
• High reverse isolation
The LT5554 is a class-A transconductance amplifier. An
input signal voltage is first converted to an output current via the LT5554 internal GM. And then, the output load
(ROUT) converts the output current into an output voltage.
ROUT sets the LT5554 gain and output noise floor. However,
the SFDR performance is almost independent of ROUT for
values of 25Ω to 100Ω.
• Overdrive protection circuit
5554f
17
LT5554
APPLICATIONS INFORMATION
The PGx gain control inputs and STROBE input can be
configured to be either DC coupled or AC coupled depending on MODE pin level. The LT5554 gain control inputs
can be connected without external components to a wide
range of user control interfaces.
The LT5554 has internal overdrive protection circuitry.
The recovery time from a short duration (less than 5ns)
overdrive pulse is 5ns.
This buffer is also connected to the input resistive attenuator network. The DEC pin is a ‘virtual ground’ and typically
connected to an external capacitor CDEC (Figures 3 and
4). When CDEC is used, the LT5554 will have same input
attenuation for both differential mode and common mode
signals. The DEC pin de-coupling capacitor improves the
common mode AC performance even when the differential
IN+, IN– inputs are imbalanced by 3dB.
The DEC pin can be used as a voltage reference for external
circuitry when DC input coupling is desired.
Input Interface
The DC voltage level at the IN+, IN– inputs are internally
biased to about 2V when the part is either enabled or
disabled. The best linearity performance is achieved when
an input imbalance is less than 2dB.
Two typical Input connection circuits are shown in Figures
3 and 4.
An input source with 50Ω (5%) is required for best gain
error performance.
RSRC/2
25Ω
Output Interface
The output interface must conduct the DC current of about
45mA to the amplifier outputs (OUT+ OUT–). Two interface
examples are shown in Figures 5 and 6.
A wide band ADC voltage interface is shown in Figure
5 where L1 and L2 are choke inductors. For a narrow
band application, a band pass filter can be placed at the
LT5554’s outputs.
5V
C1
IN+
OUT–
C5
25Ω
CDEC
0.1μF
VSRC
RSRC/2
25Ω
DEC
C2
25Ω
OUT+
DEC
IN–
OUT+
5554 F03
VCCO
ADC
BIAS
R2
C6
66.5Ω
R1
66.5Ω
LT5554
OUT–
RO
400Ω
IN+
L2
CHOKE
INDUCTORS
MAX GAIN:
GV = 24dB
GP = 18dB
LT5554
IN–
L1
C3
ADC
Figure 3. Input Capacitively-Coupled to a Differential Source
C4
5554 F05
IN+
RSRC
50Ω
•
VSRC
•
RO
400Ω
ROUT
100Ω
OUT–
RLOAD
133Ω
RSADC
100Ω
25Ω
CDEC
0.1μF
DEC
IN–
Figure 5. Differential Output Interface
LT5554
25Ω
5V
OUT+
MAX GAIN:
GV = 24dB
GP = 21dB
5554 F04
Figure 4. Input Transformer-Coupled to Single-Ended Source
Decouple (DEC) Input
The DEC pin provides the DC voltage level for differential
inputs IN+, IN– via an internal buffer, which is able to fast
charge/discharge the LT5554 input coupling capacitors
with about 30mA sourcing or sinking current capability.
C5
DEC
LT5554
OUT–
RO
400Ω
IN–
OUT+
IN+
ROUT
100Ω
R5
205Ω
VCCO
MAX GAIN INTO ZO:
GP = 18dB
T2
4:1
•
•
R6
205Ω
RO
400Ω
RLOAD
133Ω
•
ZO
50Ω
5554 F06
Figure 6. Single-Ended Matched Output Interface
5554f
18
LT5554
APPLICATIONS INFORMATION
The differential outputs can also be converted to singleended 50Ω load using a center-tap transformer interface
shown in Figure 6 and Figure 16.
Voltage clipping will occur with ROUT >140Ω, in which case
the instantaneous voltage at each OUT+ and OUT– outputs
is either <2V or >8V.
The internal 400Ω differential resistor (RO) sets the output
impedance and the maximum voltage gain (GMAX) to 36dB
when outputs OUT+, OUT– are open.
The output OP1dB = 20dBm can be achieved when ROUT =
130Ω. In this case, the LT5554 outputs reach both current
and voltage limiting for maximum output power.
Figure 7 shows the Voltage and Power Gains as a function of ROUT, which is the total output loading at the open
collector amplifier output including the internal resistor
RO = 400Ω.
VOLTAGE GAIN
MAXIMUM GAIN (dB)
30
In addition, the STROBE input can be driven such that the
LT5554 gain state is updated asynchronously (PGx latch
control in transparent-mode) or controlled by positive
STROBE transition (PGx latch control in strobed-mode).
24
POWER GAIN
12
There are several options available for coupling type and
latch control which are given in the following tables:
6
0
The MODE pin selects the interface to the LT5554 gain
control pins.
The PGx and STROBE control inputs can be configured
to be either DC-coupled (for TTL interface) or AC-coupled
(for ECL or low-voltage CMOS interfaces).
36
18
Gain Control Interface
10
50
100
ROUT (Ω)
400
1000
5554 F07
Figure 7. Maximum Voltage and Power Gain vs ROUT
The gain vs ROUT relationship is given by the following
equations:
GV = 20log(GM • ROUT) in dB
GP = 10log(RIN • GM2 • ROUT) in dB
Table1. MODE Input Options
COUPLING TYPE
MODE
(State)
STROBE
PGx
LOW
AC Positive
Transition
AC
Strobe
OPEN
DC >2.2V
AC
Transparent
OPEN
0.6 to 2.2V
AC
Strobe
HIGH
DC >2.2V
DC
Transparent
HIGH
0.6 to 2.2V
DC
Strobe
PGx (Latch Control)
Where RIN = 50Ω and GM = 0.15 siemens at GMAX
For wide band applications, the amplifier bandwidth can
be extended by inductive peaking technique. The inductor
in series with the LT5554 outputs (OUT+ OUT–) can have
a value up to some tens of nH depending on ROUT value
and board capacitance.
The current limiting will occur with ROUT <140Ω, in which
case the instantaneous signal current at the output exceeds
IODC = 45mA.
Table2. MODE Input Levels
MODE
(State)
MODE
(Min Level)
MODE
(Max Level)
LOW
0
0.6V
OPEN
1.5V
2.5V
HIGH
VCC – 0.4V
VCC
Alternatively, the MODE pin can be left open (2V
internal).
5554f
19
LT5554
APPLICATIONS INFORMATION
All seven PGx gain control inputs and STROBE input can
be configured as DC-coupled or ac-coupled. Accordingly,
there are two basic equivalent schematics (shown in Figures
8 and 9) depending on MODE input choice (Table1).
Each PGx input circuit shown in Figures 8 and 9 is followed by a transparent latch controlled by the STROBE
input level (Table 1).
The DC-coupled interface is shown in Figure 8. DC levels for
PGx inputs and STROBE input are VIL <0.6V, VIH >2.2V.
VCC
R2
1.5k
R3
1.5k
OUT+
OUT–
R1
20k
Q1
Q2
INPUT
C1
2pF
DC-COUPLED
I1
200μA
R4
20k
Q3
V1
1.4V
IDC
5554 F08
Figure 8. DC-Coupled PGx and STROBE Equivalent Inputs
(Simplified Schematic)
I3
R3
1.5k
OUT+
IDC
OUT–
R1
20k
Q1
Q2
INPUT
R4
20k
Q3
C1
2pF
AC-COUPLED
I2
IDC
I1
200μA
V1
1.4V
IDC
A HIGH-state is set by positive transitions. A LOW-state is
set by negative transitions. The PGx and STROBE inputs
appear as capacitive coupled inputs. The DC voltage (0V
to VCC range) presented on any PGx or STROBE input is
shifted to the internal 1.4V level by the additional circuit
shown in Figure 9. Each PGx and STROBE input has an
independent shift circuit such that each input can have a
different DC voltage.
Each PGx input has a parallel R-C (R1 = 20k, C1 = 2pF)
with a 40ns time constant. The STROBE input circuit has
R1 = 20k C1 = 3pF and 60ns time constant. An minimum
amplitude of 0.6VP-P is required to trip the PGx and STROBE
inputs to an appropriate state when the signal period is
less than input time constant. The circuit shown in Figure 8
converts the single-ended external signal to an internal
differential signal. Consequently, when the input is idle for
more than the input time constant, a 0.3VP-P transition
will still trigger the gain control state change. All control
inputs have 200mV hysteresis to insure stable logic levels
when the input noise level is less than 100mVP-P.
For transparent latch control, the amplifier gain will be
updated directly with any PGx input state changes. If
different PGx inputs have an (external) time skew greater
than 1ns, then a noticeable amplifier output glitch can
occur. The strobe latch control is recommended to avoid
this amplifier output glitch.
VCC
R2
1.5k
The AC-coupled interface is shown in Figure 9. The PGx
inputs and STROBE input state is decided by a signal
transition rather than signal level.
5554 F09
Figure 9. AC-Coupled PGx and STROBE Equivalent Inputs
(Simplified Schematic)
It is not necessary to double buffer the PGx inputs since
the LT5554 has good internal isolation from the PGx inputs
to the amplifier output to any type of external gain control
circuit without external components.
If LT5554 is powered up or enabled in latch mode, the
LT5554 gain initial gain is indeterminate. If the minimum
gain state is desired at power up, it is recommended to
set the transparent-mode with all PGx inputs low.
5554f
20
LT5554
APPLICATIONS INFORMATION
Gain Step Accuracy
LT5554 internal input signal coupling to the transconductance amplifier inputs across the 4dB step attenuator
increases with frequency. The gain step error is higher
when the LT5554 gain update changes the input attenuator tap (PG5, PG6 transitions) and this error is frequency
dependent.
Gain error is ‘compressive’, effectively reducing LT5554
gain range. Therefore, it is possible to skip one gain
12
code whenever PG5, PG6 transitions are involved in order to preserve high-frequency monotonic behavior for
0.125dB steps.
Linearity and Noise Performance Throughout the
Gain Range
The LT5554’s Noise and Linearity performance across
the 16dB gain range at 100MHz with ROUT = 100 and
RSADC = 50Ω is shown in Figures 10 through 13.
24
44
18
39
136
132
12
NF
3
IIP3 (dBc)
6
34
6
29
0
–16
24
128
0
0
–4
–8
–12
ATTENUATION (dB)
124
IIP3
RTI
0
SFDR (dBm/Hz)
SFDR
NF (dB)
RTI AND VONOISE (nV/√Hz)
VONOISE
9
–4
–8
–12
ATTENUATION (dB)
5554 F10
120
–16
5554 F11
Figure 10. Noise, 140MHz, ROUT = 50Ω
Figure 11. Noise, 140MHz, ROUT = 50Ω
–70
48
–70
46
–74
46
–78
44
42
48
IMD3 (dBc)
–78
44
–82
42
–82
40
–16
–86
IMD3
–86
0
–4
–8
–12
ATTENUATION (dB)
OIP3 (dBm)
OIP3 (dBm)
IMD3 (dBc)
OIP3
OIP3
–74
IMD3
5554 F12
Figure 12. Linearity, 70MHz, ROUT = 50Ω, 4dBm/Tone
0
–4
–8
–12
ATTENUATION (dB)
40
–16
5554 F12
Figure 13. Linearity, 140MHz, ROUT = 50Ω, 4dBm/Tone
5554f
21
LT5554
APPLICATIONS INFORMATION
Balanced differential inputs and outputs are important
for achieving excellent second order harmonic distortion
(HD2) of the LT5554. When configured in single-ended
input and output interfaces, therefore, the single-ended
to differential conversion at the input and differential to
single-ended conversion at the output will have significant
impact on the HD2 performance.
Figure 14, for example, shows the desirable singe-ended
input and output configuration using external transformers
for the single-ended to differential conversion and differential to single-ended conversion. To assure a good HD2
performance, R5 and R6 should also be matched to better
VCC = 5V
C4
0.1μF
IN+
T1
1:1
•
R5
68.1Ω
•
ETC1-1-13
IN–
C5
1μF
LT5554
IN+
T1
1:1
C1
47nF
ETC1-1-13
C2
47nF
C5
1μF
T2
TC2-1T
OUT–
DEC
50Ω
IN–
VCCO = 5V
LT5554
RO
400Ω
OUT+
R7
134Ω
C3
0.1μF
•
•
•
5554 F15
Figure 15. Not Recommended Single-Ended Input and Output
Configuration, HD2 = –63dBc at 10dBm, 140MHz
The HD2 performance can be further improved by mounting
a capacitor from IN+ to ground (a few pF) and a capacitor from OUT– to ground. For narrow band applications,
these capacitors cancels to some degree the T1 and T2
imbalance as shown in Figure 15.
T2
TC2-1T
R6
68.1Ω
RO
400Ω
OUT+
VCC = 5V
C4
0.1μF
VCCO = 5V
OUT–
DEC
50Ω
When the single-ended input is not converted into well
balanced inputs to LT5554, the HD2 performance will
be degraded. For instance, when the T1 transformer is
improperly rotated by 90 degrees as shown in Figure 15,
the imbalance of the differential input signals will result in
14dB degradation in HD2. It is also important to split the
differential R7 resistor into two single-ended R5 and R6
resistors at the outputs to reduce the imbalance of the T2
transformer. If not, 3dB degradation in HD2 performance
can also be observed.
•
SECOND ORDER HARMONIC DISTORTION
than 1% or use these two resistors with 1% component
tolerance. In this case, the HD2 can be as good as -80dBc
when the output power is 10dBm at 140MHz.
•
The LT5554 Noise and Linearity performance throughout
the 16dB gain range has an obvious discontinuity at every
4dB gain step. The noise figure is fairly constant from 0dB
(Maximum Gain) to –3.875dB attenuation when the gain is
decreased by lowering the amplifier transconductance. And
then, the NF increases by 4dB when the input attenuator
is switched to –4dB attenuation while the amplifier gain
is switched back to maximum transconductance. This
pattern repeats for each 4dB gain step change.
C3
0.1μF
•
•
•
5554 F14
For optimum HD2 performance, fully differential input and
output interfaces to the LT5554 part are recommended.
Figure 14. Recommended Single-Ended Input and Output
Configuration, HD2 = –80dBc at 10dBm, 140MHz
5554f
22
LT5554
APPLICATIONS INFORMATION
Layout Considerations
The transformer board from Figure 16 was used for characterization as a function of ROUT. For each ROUT option,
The T2 transformer model and the matching resistors R5,
R6 values are given in Table 3. The T2 transformer total
matching resistance is RMATCH = RO || (R5 + R6) (part
LT5554 internal, and part on board R5 and R6).
Attention must be paid to the printed circuit board layout
to avoid output pin to input pin signal coupling (external
feedback). The evaluation board layout is a good example.
The exposed backside pad on the LT5554 package must be
soldered to PCB ground plane for thermal considerations.
Table 3. Transformer Board ROUT Options
Characterization Test Circuits
ROUT (Ω)
The LT5554’s typical performance data are on the test
circuits shown in Figures 16, 17 and 18 which are simplified schematics of the evaluation board schematic from
Figure 21.
T2 (Mini-Circuits)
50
75
100
TC2-1T
TC3-1T
TC4-1W
2
3
4
57.1
92.3
133.3
NLOAD Ratio
RLOAD (Ω)
R5, R6 (Ω)
68.1
124
205
GP_BOARD (dB)
13.2
16
17.2
IL(T2) at
200MHz (dB)
–0.6
–0.65
–1
J5, 40 PINS
SMT-TB
1, 3, 5, 7
9
11
VCC VDEC
ENB
13
15
17
R20
10k
C4
0.1μF
J1
50
C8
0.1μF
PG0
23
IN–
R22
10k
PG1
RIN
50Ω
•
ETC1-1-13
MACOM
21
R21
10k
IN+
T1
1:1
•
19
25
27
29
PG0 PG1 PG2 PG3 PG4 PG5 PG6 STROBE
R23
10k
PG2
R24
10k
PG3
R5
68.1Ω
OUT–
R25
10k
PG4
PG6
C19
4.7μF
OUTPUT
MATCHING
OUT+
ROUT = 50Ω
RLOAD
57.1Ω
R6
68.1Ω
2, 4, ...40
VCCO
C3
0.1μF
RO
400Ω
RO
400Ω
33, 35, 37, 38
MODE
R26
10k
PG5
LT5554
C5
1μF
31
VPG
C9
0.1μF
C18
0.1μF
•
•
J3
50
•
T2
TC2-1T
2:1
5554 F16
VCC = 5V
VCCO = 5V
Figure 16. Single-Ended Transformer Test Board (Simplified Schematic)
5554f
23
LT5554
APPLICATIONS INFORMATION
The LT5554 output power POUT was obtained by adding
3dB for matching-loss and the transformer loss IL(T2) in
Table 3 to the board output power at J3 connector. The
transformer insertion loss (frequency and temperature
dependent) has been included in characterization.
Table 4. Balun Board ROUT Options
The output power matching is required when LT5554
drives a 50Ω transmission line as shown on the evaluation board.
VCCO (V)
ROUT (Ω)
25
36
50
71
100
R3, R4 (Ω)
0
6.49
15.4
30.1
53.6
R5, R6 (Ω)
28.7
28.7
28
28
28
0
1.88
3.66
5.76
8.08
6.29
6.57
6.96
7.61
8.66
ILPAD
The differential-output board from Figure 18 was used
for ROUT = 50Ω wide-band characterization of the LT5554
single-ended outputs.
When LT5554 drives local (on-board) loads such that
an ADC part, output power matching is not required and
OIP3 is defined based on POUT, total power at LT5554
open collector outputs.
Both Figure 17 and Figure 18 boards VCCO was shifted
up with the voltage drop on R5, R6 produced by 45mA
output DC current such that OUT+, OUT– DC bias voltage
is still 5V. The LT5554 part should be always enabled when
VCCO >6V. If disabled, the VCCO will be applied at OUT+,
OUT– exceeding the absolute maximum 6V limit with
possible LT5554 failure.
Figure 17 shows the evaluation board for wide-band
characterization at ROUT = 50Ω, where the insertion loss
of the output balun is about –1dB at 1GHz. Several ROUT
options are given in Table 4 as well as the output padding
insertion-loss and required VCCO for 5V on LT5554 outputs.
The LT5554 output power at open collector outputs is:
POUT = PWR(J3) + IL(T2) + 3dB + ILPAD
J5, 40 PINS
SMT-TB
1, 3, 5, 7
9
11
VCC VDEC
ENB
13
15
17
R20
10k
J1
50
21
R21
10k
PG0
C4
0.1μF
19
23
25
R22
10k
PG1
R23
10k
PG2
R24
10k
PG3
C8
0.1μF
•
RIN
50Ω
•
IN–
ETC1-1-13
MACOM
29
R25
10k
PG4
PG5
R5
28Ω
LT5554
RO
400Ω
R6
28Ω
OUT+
ROUT = 50Ω
33, 35, 37, 38
MODE
2, 4, ...40
VCCO
PG6
C9
0.1μF
C18
0.1μF
C19
4.7μF
R3
15.4Ω
OUT–
C5
1μF
31
VPG
R26
10k
C3
0.1μF
IN+
T1
1:1
27
PG0 PG1 PG2 PG3 PG4 PG5 PG6 STROBE
J3
50
T2
1:1
50Ω
MATCHING
R4
15.4Ω
RLOAD
RO
400Ω 57.1Ω
•
•
ETC1-1-13
5554 F17
VCC = 5V
VCCO = 7V
Figure 17. Single Ended Test Board (Simplified Schematic)
5554f
24
LT5554
APPLICATIONS INFORMATION
J5, 40 PINS
SMT-TB
1, 3, 5, 7
9
11
VCC VDEC
ENB
13
15
17
R20
10k
J1
50
21
R21
10k
23
R22
10k
PG1
PG0
C4
0.1μF
19
25
27
R23
10k
PG2
R24
10k
PG3
PG4
C8
0.1μF
•
R5
66.5Ω
LT5554
RO
400Ω
IN–
R6
66.5Ω
OUT+
C5
1μF
ETC1-1-13
MACOM
R25
10k
33, 35, 37, 38
MODE
2, 4, ...40
VCCO
R26
10k
PG5
PG6
C9
0.1μF
C18
0.1μF
C19
4.7μF
J3
50
OUT–
RIN
50Ω
•
31
VPG
C3
0.1μF
IN+
T1
1:1
29
PG0 PG1 PG2 PG3 PG4 PG5 PG6 STROBE
ROUT = 50Ω
RO
400Ω
RLOAD
57Ω
100Ω
MATCHING
C10
47nF
J33
50
C12
47nF
5554 F18
VCC = 5V
VCCO = 8V
ENB = 5V
Figure 18. Wideband Differential Output Test Board (Simplified Schematic)
Common mode characterization for the LT5554 was performed with input circuit shown in Figure 19.
C1
47nF
J1
50
25Ω
IN+
25Ω
25Ω
DEC
IN–
CDEC
47nF
OUT–
–
LT5554
+
OUT+
5554 F19
Figure 19. Common Mode Input Interface
Timing characterization and AC-coupled gain control inputs
are tested on evaluation board. The required circuit modifications are shown in the Figure 20 simplified schematic
and detailed below for PG6 (8dB step). The PG6 pulse
source is applied at J6 connector and 50Ω terminated by
R16 and R33 resistors. C66 decouple R33 to ground while
C16 provides DC-decoupling between referenced to ground
pulse source and the PG6 DC-voltage. A supply connected
to PG6 turret will set the PG6 DC-voltage in 0V to 5V range.
All other (untested) PGx DC-voltage can be independently
be applied at VPG turret decoupled by C88.
Strobe-mode operation is tested with a pulse source applied at J7 connector as shown in Figure 20.
Applying similar modifications around J2 and J4 connectors shown in Figure 21, other PGx inputs can be evaluated.
As described in Table 1 and Table 2, the MODE pin will
select the desired state.
5554f
25
LT5554
APPLICATIONS INFORMATION
R22
10k
R21
10k
R23
10k
PG1
PG2
PG4
PG3
R28
0Ω
R29
0Ω
32
R8
0Ω
1
2
3
30
29
R31
0Ω
28
27
25
GND GND
GND
ENB
DEC
GND
IN+
–
8
26
PG4
VCC
5
7
C4
0.1μF
GND
4
6
LT5554
IN
24
21
+
20
DEC
GND
GND
MODE
GND
VCC
ENABLE
22
OUT –
OUT
VCC
23
19
18
17
C8
0.1μF
PG5 GND PG6 PG0 GND STROBE GND GND
C5
1μF
R16
100Ω
31
R30
0Ω
PG1 GND PG2 PG3 GND
VDEC
VPG
C88
47nF
R24
10k
9
C16
47nF
10
R32
0Ω
11
12
R33
100Ω
13
14
15
R27 R34
0Ω 100Ω
C17
47nF
16
MODE
C6
47nF
R17
100Ω
J6
J7
PG5
R25
10k
PG6
C27
47nF
PG0
C28
47nF
R26
10k
R20
10k
5554 F20
STROBE
Figure 20. Timing Test for PG6 and STROBE (Simplified Schematic)
Evaluation Board
Figure 21 shows the schematic of the LT5554 evaluation
board. Transformer T2 is TC2-1T and resistor R5 + R6 =
134Ω (ROUT = 50Ω GP(J3) = 13.2dB). The silkscreen and
layout are shown in Figures 22 through Figure 27. The
board control J5 edge connector (40PINS SMT-TB) allows
easy access to LT5554 component pins. Alternatively or
combined with J5, 14 test points (turrets) for signals and
two for GND are also available. The board is powered with
a single supply in 4.75V to 5.25V at VCC and VCCO (either
J5 connector or turrets). Connecting the ENABLE pin to
VCC supply enables the LT5554 part. PGx gain control
and STROBE inputs will have TTL levels (DC-coupled)
when MODE = 5V (same power supply). To set LT5554 for
maximum gain (GMAX) in transparent-mode, all seven PGx
and STROBE can be connected to 5V supply. Alternatively,
a 2.2V power supply at VPG pin and STROBE turret will
set same GMAX state.
J1 (input) and J3 (output) are the default board signal
ports for evaluation with 50Ω single ended test system. For
differential evaluation, the board J11 and J33 connectors
must be reconfigured.
5554f
26
LT5554
APPLICATIONS INFORMATION
2
4
6
8
10
12
14
VCC
VCC
VCC
VCC VDEC ENB
1
3
5
7
9
11
16
20
22
24
26
28
30
32
34
PG0 PG1 PG2 PG3 PG4 PG5 PG6 STROBE VPG MODE
13
VDEC ENB
18
15
17
19
21
23
25
27
29
31
36
35
C11
47nF
R20
10k
C14
47nF
R31
0Ω
R28
0Ω
NOT MOUNTED
J4
PG2 PG3
NOT MOUNTED
C12
47nF
NOT MOUNTED
R12
NOT MOUNTED
R8
0Ω
VDEC
NOT
MOUNTED
T1
1:1
26
PG4
24
OUT–
21
5
IN–
OUT+
20
GND
MODE
GND
VCC
10
11
12
13
14
15
ENABLE
R33
0Ω
C16
47nF
NOT MOUNTED
R27
0Ω
PG6 PG0
R34
0Ω
STROBE
C17
47nF
C25
0.1μF
R3
0Ω
PG5
PG6
C27
0.1μF
C26
0.1μF
T2
–
TC2-1T OUT
2:1
•
•
R7
NC
OUT+
18
MODE
C6
47nF
17
C8
0.1μF
R4
0Ω
J33
MINICIRCUITS
R6
681Ω
C9
0.1μF
J3
•
19
16
NOT MOUNTED
NOT MOUNTED
PG4
R26
10k
R5
68.1Ω
22
PG5 GND PG6 PG0 GND STROBE GND GND
9
C24
0.1μF
R25
10k
C19
4.7μF
VCC
23
IN+
GND
C23
0.1μF
PG3
C3
0.1μF
C4
VCC
DEC
C22
0.1μF
PG2
R24
10k
VCCO
GND GND
GND
LT5554
PG1
R23
10k
C21 THROUGH C27 ARE NOT MOUNTED
25
4
C5
1μF
NOT MOUNTED
27
ENB
8
R16
28
GND
7
NOT MOUNTED
29
DEC
6
ETC1-1-13
MACOM
30
R22
10k
R14
GND
3
•
31
PG0
NOT MOUNTED
NOT MOUNTED
PG1 GND PG2 PG3 GND
1
2
R1
0Ω
C13
47nF
R21
10k
C21
0.1μF
NOT MOUNTED
R30
0Ω
R29
0Ω
32
J11
39
VPG
PG4
J2
IN–
37
VCCO
NOT MOUNTED
•
J5, 40 PINS
SMT-TB
PG0 PG1 PG2 PG3 PG4 PG5 PG6 STROBE VPG MODE
PG1
IN+
40
VCCO VCCO VCCO VCCO
33
VCC
J1
38
C18
0.1μF
R2
0Ω
NOT
MOUNTED
5554 F21
R17
NOT MOUNTED
NOT MOUNTED
J7
J6
C15
47nF
R32
0Ω
PG5
Figure 21. Evaluation Circuit Schematic
5554f
27
LT5554
APPLICATIONS INFORMATION
Figure 22. Top Side
Figure 23. Inner Layer 2 GND
5554f
28
LT5554
APPLICATIONS INFORMATION
Figure 24. Inner Layer 3 Power
Figure 25. Bottom Side
5554f
29
LT5554
APPLICATIONS INFORMATION
Figure 26. Silkscreen Top
Figure 27. Silkscreen Bottom
5554f
30
LT5554
PACKAGE DESCRIPTION
UH Package
32-Lead Plastic QFN (5mm × 5mm)
(Reference LTC DWG # 05-08-1693 Rev D)
0.70 ±0.05
5.50 ±0.05
4.10 ±0.05
3.50 REF
(4 SIDES)
3.45 ± 0.05
3.45 ± 0.05
PACKAGE OUTLINE
0.25 ± 0.05
0.50 BSC
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 ± 0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
0.75 ± 0.05
R = 0.05
TYP
0.00 – 0.05
PIN 1 NOTCH R = 0.30 TYP
OR 0.35 × 45° CHAMFER
R = 0.115
TYP
31 32
0.40 ± 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
3.50 REF
(4-SIDES)
3.45 ± 0.10
3.45 ± 0.10
(UH32) QFN 0406 REV D
0.200 REF
NOTE:
1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE
M0-220 VARIATION WHHD-(X) (TO BE APPROVED)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
0.25 ± 0.05
0.50 BSC
5554f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
31
LT5554
RELATED PARTS
PART NUMBER DESCRIPTION
COMMENTS
Infrastructure
LT5514
Ultralow Distortion, IF Amplifier/ADC Driver with
Digitally Controlled Gain
850MHz Bandwidth, 47 dBm OIP3 at 100MHz, 10.5dB to 33dB Gain
Control Range
LT5517
40MHz to 900MHz Quadrature Demodulator
21dBm IIP3, Integrated LO Quadrature Generator
LT5518
1.5GHz to 2.4GHz High Linearity Direct Quadrature
Modulator
22.8dBm OIP3 at 2GHz, –158.2dBm/Hz Noise Floor, 50Ω Single-Ended RF and
LO Ports, 4-Channel W-CDMA ACPR = –64dBc at 2.14GHz
LT5519
0.7GHz to 1.4GHz High Linearity Upconverting Mixer
17.1dBm IIP3 at 1GHz, Integrated RF Output Transformer with 50Ω Matching,
Single-Ended LO and RF Ports Operation
LT5520
1.3GHz to 2.3GHz High Linearity Upconverting Mixer
15.9dBm IIP3 at 1.9GHz, Integrated RF Output Transformer with 50Ω Matching,
Single-Ended LO and RF Ports Operation
LT5521
10MHz to 3700MHz High Linearity Upconverting Mixer
24.2dBm IIP3 at 1.95GHz, NF = 12.5dB, 3.15V to 5.25V Supply, Single-Ended LO
Port Operation
LT5522
600 MHz to 2.7GHz High Signal Level
Downconverting Mixer
4.5V to 5.25V Supply, 25dBm IIP3 at 900MHz, NF = 12.5dB, 50Ω Single-Ended
RF and LO Ports
LT5524
Low Power, Low Distortion ADC Driver with Digitally
Programmable Gain
450MHz Bandwidth, 40dBm OIP3, 4.5dB to 27dB Gain Control
LT5525
High Linearity, Low Power Downconverting Mixer
Single-Ended 50Ω RF and LO Ports, 17.6dBm IIP3 at 1900MHz, ICC = 28A
LT5526
High Linearity, Low Power Downconverting Mixer
3V to 5.3V Supply, 16.5dBm IIP3, 100kHz to 2GHz RF, NF = 11dB,
ICC = 28mA, –65dBm LO-RF Leakage
LT5527
400MHz to 3.7GHz High Signal Level
Downconverting Mixer
IIP3 = 23.5dBm and NF = 12.5dBm at 1900MHz, 4.5V to 5.25V Supply,
ICC = 78mA, Conversion Gain = 2dB
LT5528
1.5GHz to 2.4GHz High Linearity Direct Quadrature
Modulator
21.8dBm OIP3 at 2GHz, –159.3dBm/Hz Noise Floor, 50Ω, 0.5VDC Baseband
Interface, 4-Channel W-CDMA ACPR = –66dBc at 2.14GHz
LT5557
400MHz to 3.8GHz, 3.3V High Signal Level
Downconverting Mixer
IIP3 = 23.7dBm at 2600MHz, 23.5dBm at 3600MHz, ICC = 82A at 3.3V
LT5560
Ultra-Low Power Active Mixer
10mA Supply Current, 10dBm IIP3, 10dB NF, Usable as Up- or Down-Converter.
LT5568
700MHz to 1050MHz High Linearity Direct Quadrature
Modulator
22.9dBm OIP3 at 850MHz, –160.3dBm/Hz Noise Floor, 50Ω, 0.5VDC Baseband
Interface, 3-Ch CDMA2000 ACPR = –71.4dBc at 850MHz
LT5572
1.5GHz to 2.5GHz High Linearity Direct Quadrature
Modulator
21.6dBm OIP3 at 2GHz, –158.6dBm/Hz Noise Floor, High-Ohmic 0.5VDC
Baseband Interface, 4-Ch W-CDMA ACPR = –67.7dBc at 2.14GHz
LT5575
800MHz to 2.7GHz High Linearity Direct Conversion
I/Q Demodulator
50Ω, Single-Ended RF and LO Inputs. 28dBm IIP3 at 900MHz, 13.2dBm P1dB,
0.04dB I/Q Gain Mismatch, 0.4° I/Q Phase Mismatch
LT5579
1.5GHz to 3.8GHz High Linearity Upconverting Mixer
27.3dBm OIP3 at 2.14GHz, 9.9dB Noise Floor, 2.6dB Conversion Gain, –35dBm
LO Leakage
RF Power Detectors
LTC®5505
RF Power Detectors with >40dB Dynamic Range
LTC5507
100kHz to 1000MHz RF Power Detector
100kHz to 1GHz, Temperature Compensated, 2.7 to 6V Supply
LTC5508
300MHz to 7GHz RF Power Detector
44dB Dynamic Range, Temperature Compensated, SC70 Package
LTC5509
300MHz to 3GHz RF Power Detector
36dB Dynamic Range, Low Power Consumption, SC70 Package
LTC5530
300MHz to 7GHz Precision RF Power Detector
Precision VOUT Offset Control, Shutdown, Adjustable Gain
LTC5531
300MHz to 7GHz Precision RF Power Detector
Precision VOUT Offset Control, Shutdown, Adjustable Offset
LTC5532
300MHz to 7GHz Precision RF Power Detector
Precision VOUT Offset Control, Adjustable Gain and Offset
LT5534
50MHz to 3GHz Log RF Power Detector with 60dB
Dynamic Range
±1dB Output Variation over Temperature, 38ns Response Time, Log Linear
Response
LTC5536
Precision 600Mhz to 7GHz RF Power Detector with
Fast Comparator Output
25ns Response Time, Comparator Reference Input, Latch Enable Input, –26dBm
to 12dBm Input Range
LT5537
Wide Dynamic Range Log RF/IF Detector
Low Frequency to 1GHz, 83dB Log Linear Dynamic Range
LT5538
3.8GHz Wide Dynamic Range Log Detector
75dB Dynamic Range, ±1dB Output Variation Over Temperature
LT5570
2.7GHz RMS Power Detector
Fast Responding, up to 60dB Dynamic Range, ±0.3dB Accuracy Over
Temperature
300MHz to 3GHz, Temperature Compensated, 2.7V to 6V Supply
5554f
32 Linear Technology Corporation
LT 0708 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2008