LTC5598 - 5MHz to 1600MHz High Linearity Direct Quadrature Modulator

LTC5598
5MHz to 1600MHz
High Linearity Direct
Quadrature Modulator
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
Frequency Range: 5MHz to 1600MHz
High Output IP3: +27.7dBm at 140MHz
+22.9dBm at 900MHz
Low Output Noise Floor at 6MHz Offset:
No Baseband AC Input: –161.2dBm/Hz
POUT = 5.5dBm: –160dBm/Hz
Low LO Feedthrough: –55dBm at 140MHz
High Image Rejection: –50.4dBc at 140MHz
Integrated LO Buffer and LO Quadrature Phase
Generator
50Ω Single-Ended LO and RF Ports
>400MHz Baseband Bandwidth
24-Lead QFN 4mm × 4mm Package
Pin-Compatible with Industry Standard Pin-Out
Shut-down Mode
The LTC®5598 is a direct I/Q modulator designed for high
performance wireless applications, including wireless
infrastructure. It allows direct modulation of an RF signal
using differential baseband I and Q signals. It supports
point-to-point microwave link, GSM, EDGE, CDMA,
700MHz band LTE, CDMA2000, CATV applications and
other systems. It may also be configured as an image
reject upconverting mixer, by applying 90° phase-shifted
signals to the I and Q inputs.
The I/Q baseband inputs consist of voltage-to-current
converters that in turn drive double-balanced mixers.
The outputs of these mixers are summed and applied
to a buffer, which converts the differential mixer signals
to a 50Ω single-ended buffered RF output. The four
balanced I and Q baseband input ports are intended for
DC coupling from a source with a common-mode voltage
level of about 0.5V. The LO path consists of an LO buffer
with single-ended or differential inputs, and precision
quadrature generators that produce the LO drive for the
mixers. The supply voltage range is 4.5V to 5.25V, with
about 168mA current.
APPLICATIONS
n
n
n
n
n
n
n
Point-to-Point Microwave Link
Military Radio
Basestation Transmitter GSM/EDGE/CDMA2K
700MHz LTE Basestation Transmitter
Satellite Communication
CATV/Cable Broadband Modulator
13.56MHz/UHF RFID Modulator
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
Noise Floor vs RF Output Power
and Differential LO Input Power
5MHz to 1600MHz Direct Conversion Transmitter Application
VCC
LTC5598
I-DAC
1nF
x2
4.7μF
x2
RF = 5MHz
TO 1600MHz
V-I
I-CHANNEL
0o
EN
PA
90o
10nF
Q-CHANNEL
Q-DAC
BASEBAND
GENERATOR
V-I
5598 TA01
10nF
50Ω
10nF
470nF
VCO/SYNTHESIZER
–152
NOISE FLOOR AT 6MHz OFFSET (dBm/Hz)
5V
–154
–156
fLO = 140MHz; fBB = 2kHz; CW (NOTE 3)
20dBm
19.3dBm
13.4dBm
10.4dBm
8.4dBm
6.4dBm
–158
–160
–162
–14 –12 –10 –8 –6 –4 –2 0 2 4
RF OUTPUT POWER (dBm)
6
8
5598 TA02
5598f
1
LTC5598
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
GND
GND
BBPI
BBMI
VCC1
GND
TOP VIEW
Supply Voltage .........................................................5.6V
Common Mode Level of BBPI, BBMI and
BBPQ, BBMQ ...........................................................0.6V
LOP, LOM Input ....................................................20dBm
Voltage on Any Pin
Not to Exceed ...................................–0.3V to VCC + 0.3V
TJMAX .................................................................... 150°C
Operating Temperature Range..................– 40°C to 85°C
Storage Temperature Range...................–65°C to 150°C
24 23 22 21 20 19
EN 1
18 VCC2
GND 2
17 GNDRF
LOP 3
16 RF
25
LOM 4
15 NC
GND 5
14 GNDRF
CAPA 6
GND
BBMQ
GND
9 10 11 12
GND
8
BBPQ
7
CAPB
13 NC
UF PACKAGE
24-LEAD (4mm s 4mm) PLASTIC QFN
TJMAX = 150°C, θJA = 37°C/W
EXPOSED PAD (PIN 25) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC5598IUF#PBF
LTC5598IUF#TRPBF
5598
24-Lead (4mm × 4mm) Plastic QFN
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
5598f
2
LTC5598
ELECTRICAL CHARACTERISTICS
VCC = 5V, EN = 5V, TA = 25ºC, PLO = 0dBm, single-ended; BBPI, BBMI,
BBPQ, BBMQ common-mode DC voltage VCMBB = 0.5VDC, I&Q baseband input signal = 100kHz CW, 0.8VPP,DIFF each, I&Q 90° shifted
(lower side-band selection), unless otherwise noted. (Note 11)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
RF OUTPUT (RF)
fRF
RF Frequency Range
S22, ON
RF Output Return Loss
5 to 1600
EN = High, 5MHz to 1600MHz
MHz
<–20
dB
–2
dB
fLO = 140MHz, fRF = 139.9MHz
GV
Conversion Voltage Gain
20 • Log (VRF, OUT, 50Ω/VIN, DIFF, I or Q)
1VPP,DIFF on each I&Q Inputs
POUT
Absolute Output Power
OP1dB
Output 1dB Compression
2
dBm
8.5
dBm
OIP2
Output 2nd Order Intercept
(Notes 4, 5)
74
dBm
OIP3
Output 3rd Order Intercept
(Notes 4, 6)
27.7
dBm
NFloor
RF Output Noise Floor
No Baseband AC Input Signal (Note 3)
POUT = 4.6dBm (Note 3) PLO, SE = 10dBm
POUT = 5.5dBm (Note 3) PLO, DIFF = 20dBm
–161.2
–154.5
–160
dBm/Hz
dBm/Hz
dBm/Hz
IR
Image Rejection
(Note 7)
–50.4
dBc
LOFT
LO Feedthrough
(Carrier Leakage)
EN = High (Note 7)
EN = Low (Note 7)
–55
–78
dBm
dBm
fLO = 450MHz, fRF = 449.9MHz
GV
Conversion Voltage Gain
20 • Log (VRF, OUT, 50Ω/VIN, DIFF, I or Q)
–5.0
–2.1
0.5
dB
POUT
Absolute Output Power
1VPP,DIFF on each I&Q Inputs
OP1dB
Output 1dB Compression
OIP2
Output 2nd Order Intercept
OIP3
Output 3rd Order Intercept
NFloor
RF Output Noise Floor
No Baseband AC Input Signal (Note 3)
IR
Image Rejection
(Note 7)
–55
dBc
LOFT
LO Feedthrough
(Carrier Leakage)
EN = High (Note 7)
EN = Low (Note 7)
–51
–68
dBm
dBm
1.9
dBm
8.4
dBm
(Notes 4, 5)
72
dBm
(Notes 4, 6)
25.5
dBm
–160.9
dBm/Hz
fLO = 900MHz, fRF = 899.9MHz
GV
Conversion Voltage Gain
20 • Log (VRF, OUT, 50Ω/VIN, DIFF, I or Q)
–2
dB
POUT
Absolute Output Power
1VPP,DIFF on each I&Q Inputs
2
dBm
OP1dB
Output 1dB Compression
8.5
dBm
OIP2
Output 2nd Order Intercept
(Notes 4, 5)
69
dBm
OIP3
Output 3rd Order Intercept
(Notes 4, 6)
22.9
dBm
NFloor
RF Output Noise Floor
No Baseband AC Input Signal (Note 3)
POUT = 5.2dBm (Note 3) PLO, SE = 10dBm
IR
Image Rejection
(Note 7)
–54
dBc
LOFT
LO Feedthrough
(Carrier Leakage)
EN = High (Note 7)
EN = Low (Note 7)
–48
–54
dBm
dBm
–160.3
–154.5
dBm/Hz
dBm/Hz
5598f
3
LTC5598
ELECTRICAL CHARACTERISTICS
VCC = 5V, EN = 5V, TA = 25ºC, PLO = 0dBm, single-ended; BBPI, BBMI,
BBPQ, BBMQ common-mode DC voltage VCMBB = 0.5VDC, I&Q baseband input signal = 100kHz CW, 0.8VPP,DIFF each, I&Q 90° shifted
(lower side-band selection), unless otherwise noted. (Note 11)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
LO INPUT (LOP)
fLO
LO Frequency Range
5 to 1600
MHz
PLO,DIFF
Differential LO Input Power Range
–10 to 20
dBm
PLO, SE
Single-Ended LO Input Power Range
–10 to 12
dBm
S11, ON
LO Input Return Loss
EN = High
–10.5
dB
S11, OFF
LO Input Return Loss
EN = Low
–9.6
dB
BASEBAND INPUTS (BBPI, BBMI, BBPQ, BBMQ)
BWBB
Baseband Bandwidth
-3dB Bandwidth
>400
MHz
Ib,BB
Baseband Input Current
Single-Ended
–68
μA
RIN, SE
Input Resistance
Single-Ended
–7.4
kΩ
VCMBB
DC Common-Mode Voltage
Externally Applied
0.5
V
VSWING
Amplitude Swing
No Hard Clipping, Single-Ended
0.86
VP-P
POWER SUPPLY (VCC1, VCC2)
VCC
Supply Voltage
ICC(ON)
Supply Current
ICC(OFF)
Supply Current, Sleep Mode
EN = 0V, ICC1+ ICC2
tON
Turn-On Time
EN = Low to High (Notes 8, 10)
75
ns
tOFF
Turn-Off Time
EN = High to Low (Notes 9, 10)
10
ns
Input High Voltage
Input High Current
EN = High
EN = 5V
43
V
μA
Input Low Voltage
Input Low Current
EN = Low
EN = 0V
EN = High, ICC1+ ICC2
4.5
5
5.25
V
130
165
200
mA
0.24
0.9
mA
POWER UP/DOWN
Enable
Sleep
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC5598 is guaranteed functional over the operating
temperature range –40ºC to 85ºC.
Note 3: At 6MHz offset from the LO signal frequency. 100nF between BBPI
and BBMI, 100nF between BBPQ and BBMQ.
Note 4: Baseband is driven by 2MHz and 2.1MHz tones with 1VPP,DIFF for
two-tone signals at each I or Q input (0.5VPP,DIFF for each tone).
Note 5: IM2 is measured at LO frequency – 4.1MHz.
2
1
–40
V
μA
Note 6: IM3 is measured at LO frequency – 1.9 MHz and LO frequency
– 2.2MHz.
Note 7: Amplitude average of the characterization data set without image
or LO feedthrough nulling (unadjusted).
Note 8: RF power is within 10% of final value.
Note 9: RF power is at least 30dB lower than in the ON state.
Note 10: External coupling capacitors at pins LOP, LOM and RF are 100pF
each.
Note 11: Tests are performed as shown in the configuration of Figure 10.
The LO power is applied to J3 while J5 is terminated with 50Ω to ground
for single-ended LO drive.
5598f
4
LTC5598
TYPICAL PERFORMANCE CHARACTERISTICS
VCC = 5V, EN = 5V, TA = 25ºC, fRF = fLO – fBB, PLO =
0dBm single-ended, BBPI, BBMI, BBPQ, BBMQ common-mode DC voltage VCMBB = 0.5VDC , I&Q baseband input signal = 100kHz,
0.8VPP,DIFF, two-tone baseband input signal = 2MHz, 2.1MHz, 0.5VPP,DIFF each tone, I&Q 90° shifted (lower side-band selection);
fNOISE = fLO – 6MHz; unless otherwise noted. (Note 11)
Supply Current vs Temperature
Voltage Gain vs RF Frequency
Output IP3 vs RF Frequency
–1
180
29
27
–2
5.0V
160
150
–15
–3
10
35
TEMPERATURE (°C)
–5
85
60
10
23
21
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
–4
4.5V
140
–40
25
OIP3 (dBm)
VOLTAGE GAIN (dB)
SUPPLY CURRENT (mA)
5.25V
170
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
19
100
RF FREQUENCY (MHz)
17
1000
10
100
RF FREQUENCY (MHz)
1000
5598 G02
5598 G03
5598 G01
Output 1dB Compression
vs RF Frequency
Output IP2 vs RF Frequency
85
OP1dB (dBm)
70
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
60
10
6
4
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
2
100
RF FREQUENCY (MHz)
0
1000
10
100
RF FREQUENCY (MHz)
5598 G04
–40
–50
–60
–70
–70
10
100
LO FREQUENCY (MHz)
1000
5598 G07
1000
–145
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
(NOTE 3)
–150
–155
RF Two-Tone Power (Each Tone),
IM2 and IM3 vs RF Frequency
–40
0
fRF, EACH = fLO – fBB1
–50
–10
fIM3 = fLO + 2*fBB1 + fBB2
–60
–20
fIM3 = fLO – 2*fBB1 + fBB2
–30
–70
–40
–80
–160
–50
10
100
LO FREQUENCY (MHz)
5598 G06
Noise Floor vs RF Frequency
(No AC Baseband Input Signal)
NOISE FLOOR (dBm/Hz)
IMAGE REJECTION (dBc)
–30
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
–165
10
100
RF FREQUENCY (MHz)
1000
5598 G08
–60
–90
fIM2 = fLO – fBB1 – fBB2
10
IM2 (dBm), IM3 (dBm)
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
–60
5598 G05
Image Rejection vs LO Frequency
–20
–50
1000
PRF,TONE (dBm)
65
LO FEEDTHROUGH (dBm)
8
75
OIP2 (dBm)
–40
10
80
55
LO Feedthrough to RF Output
vs LO Frequency
100
1000
RF FREQUENCY (MHz)
–100
5598 G09
5598f
5
LTC5598
TYPICAL PERFORMANCE CHARACTERISTICS
VCC = 5V, EN = 5V, TA = 25ºC, fRF = fLO – fBB, PLO =
0dBm single-ended, BBPI, BBMI, BBPQ, BBMQ common-mode DC voltage VCMBB = 0.5VDC , I&Q baseband input signal = 100kHz,
0.8VPP,DIFF, two-tone baseband input signal = 2MHz, 2.1MHz, 0.5VPP,DIFF each tone, I&Q 90° shifted (lower side-band selection);
fNOISE = fLO – 6MHz; unless otherwise noted. (Note 11)
RF Two-Tone Power (Each Tone),
IM2 and IM3 vs Baseband Voltage
and Temperature (fLO = 900MHz)
0
–40
0
–10
–50
–20
fRF, EACH = fLO –fBB1
fIM3 = fLO – 2*fBB1 + fBB2
fIM3 = fLO + 2*fBB1 + fBB2
fIM2 = fLO – fBB1 – fBB2
–60
–70
–30
–80
–40
–30
–90
–50
0.1
1
I AND Q BASEBAND VOLTAGE (VPP, DIFF, EACH TONE)
–50
–10
fIM3 = fLO + 2*fBB1 + fBB2
–20
–60
–30 f
IM3 = fLO – 2*fBB1 + fBB2
–70
fIM2 = fLO – fBB1 – fBB2
27
80
25
75
17
10
100
RF FREQUENCY (MHz)
1000
5598 G15
RF Two-Tone Power (Each Tone),
IM2 and IM3 vs RF Frequency
(PLO = 10dBm)
0
–40
fRF, EACH = fLO – fBB1
fIM3 = fLO + 2*fBB1 + fBB2
PRF, TONE (dBm)
IMAGE REJECTION (dBc)
LO FEEDTHROUGH (dBm)
5598 G16
100
RF FREQUENCY (MHz)
–40
–50
fIM3 = fLO – 2*fBB1 + fBB2
–60
–70
IM2 (dBm), IM3 (dBm)
1000
10
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
–30
100
LO FREQUENCY (MHz)
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
0
1000
–20
10
4
2
Image Rejection vs LO Frequency
(PLO = 10dBm)
–40
–70
6
5598 G14
LO Feedthrough to RF Output
vs LO Frequency (PLO = 10dBm)
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
1000
Output 1dB Compression
vs RF Frequency (PLO = 10dBm)
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
5598 G13
–60
100
RF FREQUENCY (MHz)
5598 G12
70
55
1000
–50
10
8
60
100
RF FREQUENCY (MHz)
–5
10
65
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
10
–80
OP1dB (dBm)
85
OIP2 (dBm)
OIP3 (dBm)
29
19
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
–4
Output IP2 vs RF Frequency
(PLO = 10dBm)
23
–3
5598 G11
Output IP3 vs RF Frequency
(PLO = 10dBm)
21
–2
–90
–50
0.1
1
I AND Q BASEBAND VOLTAGE (VPP, DIFF, EACH TONE)
5598 G10
PLO = 10dBm
–40
fRF, EACH = fLO – fBB1
–40
–1
VOLTAGE GAIN (dB)
10
PRF,TONE (dBm)
–30
Voltage Gain vs RF Frequency
(PLO = 10dBm)
IM2 (dBm), IM3 (dBm)
10
IM2 (dBm), IM3 (dBm)
PRF, TONE (dBm)
RF Two-Tone Power (Each Tone),
IM2 and IM3 vs Baseband Voltage
and Temperature (fLO = 140MHz)
fIM2 = fLO – fBB1 – fBB2
10
100
LO FREQUENCY (MHz)
1000
5598 G17
–60
10
100
RF FREQUENCY (MHz)
1000
–100
5598 G18
5598f
6
LTC5598
TYPICAL PERFORMANCE CHARACTERISTICS
VCC = 5V, EN = 5V, TA = 25ºC, fRF = fLO – fBB, fLO =
450MHz, PLO = 0dBm single-ended, BBPI, BBMI, BBPQ, BBMQ common-mode DC voltage VCMBB = 0.5VDC , I&Q baseband input signal
= 100kHz, 0.8VPP,DIFF, two-tone baseband input signal = 2MHz, 2.1MHz, 0.5VPP,DIFF each tone, I&Q 90° shifted (lower side-band
selection); fNOISE = fLO – 6MHz; unless otherwise noted. (Note 11)
Noise Floor vs RF Frequency
(PLO = 10dBm, No AC Baseband
Input Signal)
0
5V, 25°C
5.25V, 25°C
4.5V, 25°C
5V, –40°C
5V, 85°C
(NOTE 3)
–155
–160
–10
C8 = 0
–40°C
IMAGE REJECTION (dBc)
–150
–40
LO FEEDTHROUGH (dBm)
NOISE FLOOR (dBm/Hz)
–145
Image Rejection vs LO Frequency
(PLO = 10dBm)
LO Feedthrough to RF Output
vs LO Frequency for EN = Low
–60
–80
PLO = 10dBm
–100
85°C
PLO = 0dBm
–20
–30
–40
–50
–60
C8 = 470nF
–120
–70
–165
–140
10
100
RF FREQUENCY (MHz)
10
1000
100
LO FREQUENCY (MHz)
Noise Floor vs RF Output Power and
Differential LO Input Power
40
30
20
10
–162
–14 –12 –10 –8 –6 –4 –2 0 2 4
RF OUTPUT POWER (dBm)
6
0
8
85oC
25oC
–40oC
35
–2.4
–2.3
–2.2
–2.1
GAIN (dB)
–2
0
–1.9
Noise Floor Distribution
70
85oC
25oC
–40oC
60
NO RF
PERCENTAGE (%)
10
25
20
15
5598 G23
0
50
40
30
10
5
–70 –66 –62 –58 –54 –50 –46 –42 –38
LO FEEDTHROUGH (dBm)
85oC
25oC
–40oC
20
10
5
24 24.4 24.8 25.2 25.6 26 26.4 26.8 27.2
OIP3 (dBm)
5598 G22
30
PERCENTAGE (%)
PERCENTAGE (%)
10
Image Rejection Distribution
40
15
0
15
5598 G21
LO Feedthrough Distribution
20
20
5
5598 G20b
25
25
PERCENTAGE (%)
PERCENTAGE (%)
NOISE FLOOR AT 6MHz OFFSET (dBm/Hz)
50
–160
30
85oC
25oC
–40oC
fLO = 140MHz; fBB = 2kHz; CW (NOTE 3)
–158
1000
Output IP3 Distribution at 25°C
60
–156
100
LO FREQUENCY (MHz)
5598 G20a
Gain Distribution
–152
20dBm
19.3dBm
13.4dBm
10.4dBm
8.4dBm
6.4dBm
10
5598 G20
5598 G19
–154
–80
1000
–70 –66 –62 –58 –54 –50 –46 –42
IMAGE REJECTION (dBc)
5598 G24
0
–162.4 –162 –161.6 –161.2 –160.8 –160.4 –160
NOISE FLOOR (dBm/Hz)
5598 G25
5598f
7
LTC5598
PIN FUNCTIONS
EN (Pin 1): Enable Input. When the Enable Pin voltage is
higher than 2 V, the IC is turned on. When the input voltage
is less than 1 V, the IC is turned off. If not connected, the
IC is enabled.
NC (Pins 13, 15): No Connect. These pins are floating.
GNDRF (Pins 14, 17): Ground. Pins 14 and 17 are connected
to each other internally and function as the ground return for
the RF output buffer. They are connected via back-to-back
diodes to the exposed pad 25. For best LO suppression
performance those pins should be grounded separately
from the exposed paddle 25. For best RF performance,
pins 14 and 17 should be connected to RF ground.
GND (Pins 2, 5, 8, 11, 12, 19, 20, 23 and 25): Ground.
Pins 2, 5, 8, 11, 12, 19, 20, 23 and exposed pad 25 are
connected to each other internally. For best RF performance,
pins 2, 5, 8, 11, 12, 19, 20, 23 and the Exposed Pad 25
should be connected to RF ground.
RF (Pin 16): RF Output. The RF output is a DC-coupled
single-ended output with approximately 50Ω output
impedance at RF frequencies. An AC coupling capacitor
should be used at this pin to connect to an external
load.
LOP (Pin 3): Positive LO Input. This LO input is internally
biased at about 2.3V. An AC de-coupling capacitor should
be used at this pin to match to an external 50Ω source.
LOM (Pin 4): Negative LO Input. This input is internally biased
at about 2.3V. An AC de-coupling capacitor should be used at
this pin via a 50Ω to ground for best OIP2 performance.
VCC (Pins 18, 24): Power Supply. It is recommended to
use 1nF and 4.7μF capacitors for decoupling to ground
on each of these pins.
CAPA, CAPB (Pins 6, 7): External capacitor pins. A capacitor between the CAPA and the CAPB pin can be used in
order to improve the image rejection for frequencies below
100MHz. A capacitor value of 470nF is recommended.
These pins are internally biased at about 2.3V.
BBPI, BBMI (Pins 21, 22): Baseband Inputs for the Qchannel, each high input impedance. They should be
externally biased at 0.5V common-mode level and not be
left floating. Applied common-mode voltage must stay
below 0.6VDC.
BBMQ, BBPQ (Pins 9, 10): Baseband Inputs for the
Q-channel, each high input impedance. They should be
externally biased at 0.5V common-mode level and not be
left floating. Applied common-mode voltage must stay
below 0.6VDC.
Exposed Pad (Pin 25): Ground. This pin must be soldered
to the printed circuit board ground plane.
BLOCK DIAGRAM
VCC1 VCC2
GND
20
23
25
24
NC
18
13
15
LTC5598
BBPI 21
V-I
BBMI 22
0o
EN
1
16 RF
90o
BBPQ 10
14
V-I
BBMQ 9
GNDRF
17
2
5
8
GND
11
3
4
6
7
LOP LOM CAPA CAPB
12
19
5598 BD
GND
5598f
8
LTC5598
APPLICATIONS INFORMATION
The LTC5598 consists of I and Q input differential voltageto-current converters, I and Q up-conversion mixers, an
RF output buffer, an LO quadrature phase generator and
LO buffers.
External I and Q baseband signals are applied to the
differential baseband input pins, BBPI, BBMI, and BBPQ,
BBMQ. These voltage signals are converted to currents and
translated to RF frequency by means of double-balanced
up-converting mixers. The mixer outputs are combined
in an RF output buffer, which also transforms the output
impedance to 50Ω. The center frequency of the resulting
RF signal is equal to the LO signal frequency. The LO input
drives a phase shifter which splits the LO signal into inphase and quadrature LO signals. These LO signals are then
applied to on-chip buffers which drive the up-conversion
mixers. In most applications, the LOP input is driven by
the LO source via an optional matching network, while
the LOM input is terminated with 50Ω to RF ground via
a similar optional matching network. The RF output is
single-ended and internally 50Ω matched.
Baseband Interface
The circuit is optimized for a common mode voltage of
0.5V which should be externally applied. The baseband
pins should not be left floating because the internal
PNP’s base current will pull the common mode voltage
higher than the 0.6V limit. This condition may damage
the part. In shut-down mode, it is recommended to have
a termination to ground or to a 0.5V source with a value
lower than 1kΩ. The PNP’s base current is about –68μA
in normal operation.
The baseband inputs (BBPI, BBMI, BBPQ, BBMQ) present
a single-ended input impedance of about –7.4kΩ each.
Because of the negative input impedance, it is important
to keep the source resistance at each baseband input low
enough such that the parallel value remains positive vs
baseband frequency. At each of the four baseband inputs, a
capacitor of 4pF in series with 30Ω is connected to ground.
This is in parallel with a PNP emitter follower (see Figure 1).
The baseband bandwidth depends on the source impedance.
For a 25Ω source impedance, the baseband bandwidth
(–1dB) is about 300MHz. If a 5.6nH series inductor is
inserted in each of the four baseband connections, the
–1dB baseband bandwidth increases to about 800MHz.
It is recommended to include the baseband input impedance
in the baseband lowpass filter design. The input impedance
of each baseband input is given in Table 1.
Table 1. Single-Ended BB Port Input Impedance vs Frequency
for EN = High and VCMBB = 0.5VDC
FREQUENCY
(MHz)
BB INPUT
IMPEDANCE
REFLECTION COEFFICIENT
MAG
ANGLE
0.1
–10578 – j263
1.01
–0.02
1
–8436 – j1930
1.011
–0.15
2
–6340 – j3143
1.013
–0.36
4
–3672 – j3712
1.014
–0.78
8
–1644 – j2833
1.015
–1.51
16
–527 – j1765
1.016
–2.98
30
–177 – j1015
1.017
–5.48
60
–45.2 – j514
1.017
–11
100
–13.2 – j306
1.014
–18.5
140
–0.2 – j219
1
–25.7
200
4.5 – j151
0.982
–36.6
300
10.4 – j99.4
0.921
–52.9
400
12.3 – j72.4
0.854
–68.2
500
14.7 – j57.5
0.780
–79.9
600
15.5 – j46.3
0.720
–91.4
The baseband inputs should be driven differentially;
otherwise, the even-order distortion products may degrade
the overall linearity performance. Typically, a DAC will
LTC5598
VCC2 = 5V
BUFFER
RF
VCC1 = 5V
FROM
Q
LOMI
LOPI
BBPI
30Ω
4pF
VCMBB = 0.5VDC
4pF
30Ω
BBMI
GNDRF
55682 F01
GND
Figure 1. Simplified Circuit Schematic
of the LTC5598 (Only I-Half is Drawn)
5598f
9
LTC5598
APPLICATIONS INFORMATION
be the signal source for the LTC5598. A reconstruction
filter should be placed between the DAC output and the
LTC5598’s baseband inputs.
In Figure 2 a typical baseband interface is shown, using
a fifth-order lowpass ladder filter.
L1A
0mA TO 20mA
L2A
0.5VDC
R1A
1007
DAC
C2
C1
R1B
1007
BBPI
R2A
1007
L1B
L2B
0mA TO 20mA
C3
R2B
1007
0.5VDC
GND
BBMI
5598 F02
Figure 2. Baseband Interface with 5th Order Filter
and 0.5VCM DAC (Only I Channel is Shown)
in Table 3. In Table 4 and 5, the LOP port input impedance
is given for EN = High and Low under the condition of
PLO = 10dBm. Figure 4 shows the LOP port return loss
for the standard demo board (schematic is shown in
Figure 10) when the LOM port is terminated with 50Ω to
GND. The values of L1, L2, C9 and C10 are chosen such
that the bandwidth for the LOP port of the standard demo
board is maximized while meeting the LO input return loss
S11, ON < –10dB.
Table 2. LOP Port Input Impedance vs Frequency for EN = High
and PLO = 0dBm (LOM AC Coupled With 50Ω to Ground).
FREQUENCY
(MHz)
For each baseband pin, a 0 to 1V swing is developed
corresponding to a DAC output current of 0mA to 20mA.
The maximum sinusoidal single side-band RF output power
is about +7.3dBm for full 0V to 1V swing on each I- and
Q- channel baseband input (2VPP, DIFF).
LO Section
The internal LO chain consists of poly-phase phase shifters
followed by LO buffers. The LOP input is designed as a
single-ended input with about 50Ω input impedance. The
LOM input should be terminated with 50Ω through a DC
blocking capacitor.
The LOP and LOM inputs can be driven differentially in
case an exceptionally low large-signal output noise floor
is required (see graph 5598 G20b).
A simplified circuit schematic for the LOP, LOM, CAPA
and CAPB inputs is given in Figure 3. A feedback path is
implemented from the LO buffer outputs to the LO inputs
in order to minimize offsets in the LO chain by storing the
offsets on C5, C7 and C8 (see Figure 10). Optional capacitor
C8 improves the image rejection below 100MHz (see
graph 5598 G20a). Because of the feedback path, the input
impedance for PLO = 0dBm is somewhat different than
for PLO = 10dBm for the lower part of the operating
frequency range. In Table 2, the LOP port input impedance
vs frequency is given for EN = High and PLO = 0dBm. For
EN = Low and PLO = 0dBm, the input impedance is given
REFLECTION COEFFICIENT
LO INPUT
IMPEDANCE
MAG
ANGLE
0.1
333 – j10.0
0.739
–0.5
1
318 – j59.9
0.737
–3.3
2
285 – j94.7
0.728
–6.1
4
227 – j120
0.708
–10.6
8
154 – j124
0.678
–18.7
16
89.9 – j95.4
0.611
–33.0
30
60.4 – j60.6
0.420
–41.3
60
54.8 – j35.8
0.489
–51.5
100
43.6 – j24.4
0.261
–89.9
200
37.9 – j17.3
0.235
–113
400
31.8 – j12.4
0.266
–137
800
23.6 – j8.2
0.374
–156
1000
19.8 – j5.5
0.437
–165
1250
16.0 – j1.8
0.515
–175
1500
13.6 + j2.4
0.574
174
1800
12.1 + j7.3
0.618
162
VCC1
LOP
LOM
CAPB
CAPA
+ 2.8V
(4.3V IN
SHUTDOWN)
5598 F03
Figure 3. Simplified Circuit Schematic for the
LOP, LOM, CAPA and CAPB Inputs.
5598f
10
LTC5598
APPLICATIONS INFORMATION
Table 3. LOP Port Input Impedance vs Frequency for EN = Low
and PLO = 0dBm (LOM AC Coupled with 50Ω to Ground).
FREQUENCY
(MHz)
LO INPUT
IMPEDANCE
0.1
1376 – j84.4
1
541 – j1593
2
177 – j877
4
75.3 – j452
8
REFLECTION COEFFICIENT
Table 5. LOP Port Input Impedance vs Frequency for EN = Low
and PLO = 10dBm (LOM AC Coupled with 50Ω to Ground).
MAG
ANGLE
MAG
ANGLE
0.930
–0.3
0.1
454 – j30.5
0.802
–0.9
0.980
–3.2
1
423 – j102
0.780
–3.2
0.977
–6.2
2
365 – j165
0.796
–5.9
0.965
–12.2
4
249 – j219
0.798
–11.4
49.2 – j228
0.918
–23.6
8
117 – j179
0.781
–22.4
16
43.3 – j117
0.784
–41.8
16
60.7 – j106
0.697
–40.3
30
40.7 – j64.1
0.585
–62.7
30
43.1 – j62.0
0.559
–62.4
60
39.1 – j34.6
0.382
–86
100
37.6 – j23.8
0.296
–102
200
33.4 – j16.4
0.275
–124
400
27.5 – j11.1
0.320
–145
800
20.1 – j4.9
0.430
–167
1000
17.5 – j1.6
0.479
–176
1250
15.3 + j2.1
0.532
175
1500
13.8 + j5.6
0.571
167
1800
12.8 + j9.7
0.605
157
60
38.6 – j34.6
0.386
–86.7
100
37.6 – j23.9
0.297
–102
200
33.5 – j16.5
0.274
–124
400
27.6 – j11.3
0.319
–145
800
20.2 – j5.1
0.429
–166
1000
17.7 – j1.7
0.478
–175
1250
15.2 + j2.0
0.533
175
1500
13.9 + j5.4
0.570
167
1800
12.9 + j9.5
0.604
158
Table 4. LOP Port Input Impedance vs Frequency for EN = High
and PLO = 10dBm (LOM AC Coupled with 50Ω to Ground).
LO INPUT
IMPEDANCE
0.1
1
0
REFLECTION COEFFICIENT
MAG
ANGLE
360-j14.8
0.756
–0.7
349-j70.5
0.758
–3.2
2
311-j113
0.752
–6.0
4
240-j148
0.739
–10.9
8
148-j146
0.715
–19.7
16
81.3-j102
0.641
–35.2
30
55.4-j61.6
0.506
–54.7
60
45.7-j34.4
0.341
–77.4
100
43.0-j24.1
0.261
–91.6
200
38.0-j17.1
0.234
–114
400
32.0-j12.5
0.265
–137
800
23.6-j8.3
0.374
–156
1000
19.8-j5.6
0.438
–165
1250
15.8-j1.7
0.520
–176
1500
13.5+j2.4
0.575
174
1800
12.0+j7.3
0.619
162
–5
RETURN LOSS (dB)
FREQUENCY
(MHz)
LO INPUT
IMPEDANCE
REFLECTION COEFFICIENT
FREQUENCY
(MHz)
–10
–15
EN = LOW; PLO = 0dBm
EN = LOW; PLO = 10dBm
EN = HIGH; PLO = 0dBm
EN = HIGH; PLO = 10dBm
C9, C10: 2.2pF; L1, L2: 3.3nH;
C5, C7: 10nF
–20
–25
1
100
10
FREQUENCY (MHz)
1000
5598 F04
Figure 4. LOP Port Return Loss vs Frequency
for Standard Board (See Figure 10)
5598f
11
LTC5598
APPLICATIONS INFORMATION
The LOP port return loss for the low end of the operating
frequency range can be optimized using extra 120Ω
terminations at the LO inputs (replace C9 and C10 with 120Ω
resistors, see Figure 10), and is shown in Figure 5.
–4
C9, C10: 120Ω; L1, L2: 0Ω; C5, C7: 100nF
EN = LOW; PLO = 0dBm
RETURN LOSS (dB)
–6
EN = LOW; PLO = 10dBm
–5
–10
The large-signal noise figure can be improved with a
higher LO input power. However, if the LO input power is
too large and causes internal clipping in the phase shifter
section, the image rejection can be degraded rapidly. This
clipping point depends on the supply voltage, LO frequency,
temperature and single-ended vs differential LO drive. At
fLO = 140MHz, VCC = 5V, T = 25°C and single-ended LO
drive, this clipping point is at about 16.6dBm. For 4.5V it
lowers to 14.6dBm. For differential drive with VCC = 5V it
is about 20dBm.
The differential LO port input impedance for EN = High
and PLO = 10dBm is given in Table 6.
–12
EN = HIGH; PLO = 10dBm
EN = HIGH; PLO = 0dBm
–14
1
100
10
FREQUENCY (MHz)
1000
Table 6. LOP - LOM Port Differential Input Impedance
vs Frequency for EN = High and PLO = 10dBm
FREQUENCY
(MHz)
LO DIFFERENTIAL
INPUT IMPEDANCE
Figure 5. LO Port Return Loss vs Frequency
Optimized for Low Frequency (See Figure 10)
0.1
642 – j25.7
1.0
626 – j112
The LOP port return loss for the high end of the operating
frequency range can be optimized using slightly different
values for C9, C10 and L1, L2 (see Figure 6).
2.0
572 – j204
4.0
429 – j305
8.0
222 – j287
16
102 – j181
30
64.2 – j104
60
50.9 – j58.9
100
46.2 – j40.2
200
37.4 – j28.6
400
28.3 – j19.4
800
20.0 – j10.6
1000
17.5 – j7.9
1250
16.6 – j2.7
1500
17.3 + j3.3
1800
20.6 + j10.2
5598 F05
0
RETURN LOSS (dB)
–10
EN = LOW
–20
EN = HIGH
–30
C9, C10: 2.7pF; L1, L2: 1.5nH; C5, C7: 10nF
–40
1400
1600
1800
2000
1000
1200
FREQUENCY (MHz)
5598 F06
Figure 6. LO Port Return Loss vs Frequency
Optimized for High Frequency (See Figure 10)
The third-harmonic rejection on the applied LO signal is
recommended to be equal or better than the desired image
rejection performance since third-harmonic LO content can
degrade the image rejection severely. Image rejection is
not sensitive to second-harmonic LO content.
RF Section
After upconversion, the RF outputs of the I and Q mixers are
combined. An on-chip buffer performs internal differential
to single-ended conversion, while transforming the output
impedance to 50Ω. Table 7 shows the RF port output
impedance vs frequency for EN = High.
5598f
12
LTC5598
APPLICATIONS INFORMATION
Table 7. RF Output Impedance vs Frequency for EN = High
FREQUENCY
(MHz)
RF OUTPUT
IMPEDANCE
REFLECTION COEFFICIENT
MAG
ANGLE
0.1
59.0 – j0.6
0.083
–3.6
1
58.5 – j2.1
0.081
–12.7
2
57.3 – j3.5
0.076
–23.6
4
54.6 – j4.5
0.061
–41.6
8
51.9 – j3.6
0.040
–60.8
16
50.5 – j2.1
0.022
–74.8
30
50.2 – j1.1
0.011
–80
60
50 – j0.5
0.005
–86.5
100
50 – j0.2
0.002
–84.9
200
49.7 + j0
0.003
177.4
400
48.9 + j0.3
0.011
162
800
46.1 + j0.4
0.041
173.3
1000
44.5 + j0.2
0.058
178
1250
42.8 + j0
0.077
–179.7
1500
41.2 – j0.1
0.097
–179.4
1800
39.9 + j0.4
0.113
177.4
must be below 1V. If the EN pin is not connected, the chip
is enabled. This EN = High condition is assured by the 125k
on-chip pull-up resistor. It is important that the voltage at
the EN pin does not exceed VCC by more than 0.3V. Should
VCC2
1k
4.6V
FROM
INTERNAL
MIXERS
1V
INTERNAL
BIAS
EN = LOW
–10
RETURN LOSS (dB)
100
ANGLE
82.3 – j1223
0.995
–4.6
200
51.1 – j618
0.987
–9.2
400
35.3 – j310
0.965
–18.1
800
24.4 – j148
0.906
–36.6
1000
20.4 – j114
0.878
–46.4
1250
17 – j87
0.847
–58.4
1500
14.7 – j68
0.818
–70.7
1800
13.1 – j54
0.785
–84.3
In Figure 7 the simplified circuit schematic of the RF
output buffer is drawn. A plot of the RF port return loss vs
frequency is drawn in Figure 8 for EN = High and Low.
5598 F07
0
REFLECTION COEFFICIENT
MAG
48Ω
1k
Figure 7. Simplified Circuit Schematic of the RF Output
Table 8. RF Output Impedance vs Frequency for EN = Low
LO INPUT
IMPEDANCE
RF
1.8V
The RF port output impedance for EN = Low is given in Table
8. It is roughly equivalent to a 1.3pF capacitor to ground.
FREQUENCY
(MHz)
2.8V
48Ω
–20
EN = HIGH
–30
–40
–50
C6 = 220nF, SEE FIGURE 10
–60
100
10
FREQUENCY (MHz)
1
1000
5598 F08
Figure 8. RF Port Return Loss vs Frequency
VCC1
125k
3V
50k
EN
2V
INTERNAL
ENABLE
CIRCUIT
Enable Interface
Figure 9 shows a simplified schematic of the EN pin
interface. The voltage necessary to turn on the LTC5598
is 2V. To disable (shut down) the chip, the enable voltage
5598 F09
Figure 9: EN Pin Interface
5598f
13
LTC5598
APPLICATIONS INFORMATION
this occur, the supply current could be sourced through
the EN pin ESD protection diodes, which are not designed
to carry the full supply current, and damage may result.
Evaluation Board
Figure 10 shows the evaluation board schematic. A good
ground connection is required for the exposed pad. If this
is not done properly, the RF performance will degrade.
Additionally, the exposed pad provides heat sinking for the
part and minimizes the possibility of the chip overheating.
Resistors R1 and R2 reduce the charging current in
capacitors C1 and C4 (see Figure 10) and will reduce
supply ringing during a fast power supply ramp-up in
case an inductive cable is connected to the VCC and GND
turrets. For EN = High, the voltage drop over R1 and R2
is about 0.15V. If a power supply is used that ramps up
slower than 10V/μs and limits the overshoot on the supply
below 5.6V, R1 and R2 can be omitted.
Figure 11. Component Side of Evaluation Board
The LTC5598 can be used for base-station applications
with various modulation formats. Figure 13 shows a
typical application.
J2
J1
BBPI
BBMI
VCC
C1
4.7μF
RF
LOM
NC
GND
GNDRF
CAPB
C10
2.2pF
7
8
9
NC
10 11 12
17
J4
16
RF OUT
15
C6
10nF
14
13
GND
25
C8
470nF
U1
LTC5598
J6
GND
C4
4.7μF
18
GND
CAPA
GND
6
GNDRF
BBPQ
5
C7
10nF
VCC2
LOP
BBMQ
L2
3.3nH
C3
1nF
GND
GND
J5
LOM
GND
4
GND
3
EN
BBPI
2
BBMI
LOP
1
C5
L1
10nF
3.3nH
GND
J3
R2
5.6Ω
24 23 22 21 20 19
EN
VCC1
C9
2.2pF
R1
1Ω
C2
1nF
BBMQ
J7
BBPQ
BOARD NUMBER: DC1455A
Figure 12. Bottom Side of Evaluation Board
5598 F10
Figure 10. Evaluation Circuit Schematic
5598f
14
LTC5598
APPLICATIONS INFORMATION
5V
1nF
x2
VCC 18, 24
I-DAC
22
V-I
NC
I-CHANNEL
0o
1
EN
9
BASEBAND
GENERATOR
RF = 5MHz
TO 1600MHz
13, 15
16
90o
10
Q-DAC
4.7μF
x2
LTC5598
21
PA
10nF
Q-CHANNEL
14, 17
V-I
3
4
2, 5, 8, 11, 12,
19, 20, 23, 25
6
7
5598 F13
10nF
10nF
50Ω
470nF
VCO/SYNTHESIZER
Figure 13: 5MHz to 1600MHz Direct
Conversion Transmitter Application
PACKAGE DESCRIPTION
UF Package
24-Lead (4mm × 4mm) Plastic QFN
(Reference LTC DWG # 05-08-1697)
0.70 p0.05
4.50 p 0.05
2.45 p 0.05
3.10 p 0.05 (4 SIDES)
PACKAGE OUTLINE
0.25 p0.05
0.50 BSC
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
4.00 p 0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
R = 0.115
TYP
0.75 p 0.05
PIN 1 NOTCH
R = 0.20 TYP OR
0.35 s 45o CHAMFER
23 24
PIN 1
TOP MARK
(NOTE 6)
0.40 p 0.10
1
2
2.45 p 0.10
(4-SIDES)
(UF24) QFN 0105
0.200 REF
0.00 – 0.05
0.25 p 0.05
0.50 BSC
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
5598f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LTC5598
RELATED PARTS
PART NUMBER
Infrastructure
LT5514
DESCRIPTION
COMMENTS
Ultralow Distortion, IF Amplifier/ADC Driver
with Digitally Controlled Gain
40MHz to 900MHz Quadrature Demodulator
1.5GHz to 2.4GHz High Linearity Direct
Quadrature Modulator
850MHz Bandwidth, 47dBm OIP3 at 100MHz, 10.5dB to 33dB Gain Control Range
LT5519
0.7GHz to 1.4GHz High Linearity Upconverting
Mixer
17.1dBm IIP3 at 1GHz, Integrated RF Output Transformer with 50Ω Matching,
Single-Ended LO and RF Ports Operation
LT5520
1.3GHz to 2.3GHz High Linearity Upconverting
Mixer
LT5521
10MHz to 3700MHz High Linearity
Upconverting Mixer
600MHz to 2.7GHz High Signal Level
Downconverting Mixer
15.9dBm IIP3 at 1.9GHz, Integrated RF Output Transformer with 50Ω Matching,
Single-Ended LO and RF Ports Operation
24.2dBm IIP3 at 1.95GHz, NF = 12.5dB, 3.15V to 5.25V Supply, Single-Ended LO
Port Operation
LT5517
LT5518
LT5522
LT5527
LT5528
LT5554
LT5557
LT5560
LT5568
400MHz to 3.7GHz High Signal Level
Downconverting Mixer
1.5GHz to 2.4GHz High Linearity Direct
Quadrature Modulator
Broadband Ultra Low Distortion 7-Bit Digitally
Controlled VGA
400MHz to 3.8GHz High Signal Level
Downconverting Mixer
Ultra-Low Power Active Mixer
700MHz to 1050MHz High Linearity Direct
Quadrature Modulator
LT5571
620MHz - 1100MHz High Linearity Quadrature
Modulator
LT5572
1.5GHz to 2.5GHz High Linearity Direct
Quadrature Modulator
LT5575
800MHz to 2.7GHz High Linearity Direct
Conversion I/Q Demodulator
LT5579
1.5GHz to 3.8GHz High Linearity
Upconverting Mixer
RF Power Detectors
LTC®5505
RF Power Detectors with >40dB Dynamic Range
LTC5507
100kHz to 1000MHz RF Power Detector
LTC5508
300MHz to 7GHz RF Power Detector
LTC5509
300MHz to 3GHz RF Power Detector
LTC5530
300MHz to 7GHz Precision RF Power Detector
LTC5531
300MHz to 7GHz Precision RF Power Detector
LTC5532
300MHz to 7GHz Precision RF Power Detector
LT5534
50MHz to 3GHz Log RF Power Detector with
60dB Dynamic Range
LTC5536
LT5537
LT5538
Precision 600MHz to 7GHz RF Power Detector
with Fast Comparator Output
Wide Dynamic Range Log RF/IF Detector
3.8GHz Wide Dynamic Range Log Detector
LT5570
2.7GHz RMS Power Detector
LT5581
40dB Dynamic Range RMS Detector
21dBm IIP3, Integrated LO Quadrature Generator
22.8dBm OIP3 at 2GHz, –158.2dBm/Hz Noise Floor, 50Ω Single-Ended RF and LO
Ports, 4-Channel W-CDMA ACPR = –64dBc at 2.14GHz
4.5V to 5.25V Supply, 25dBm IIP3 at 900MHz, NF = 12.5dB, 50Ω Single-Ended RF
and LO Ports
IIP3 = 23.5dBm and NF = 12.5dBm at 1900MHz, 4.5V to 5.25V Supply, ICC = 78mA,
Conversion Gain = 2dB.
21.8dBm OIP3 at 2GHz, –159.3dBm/Hz Noise Floor, 50Ω, 0.5VDC Baseband
Interface, 4-Channel W-CDMA ACPR = –66dBc at 2.14GHz
48dBm OIP3 at 200MHz, 1.4nV/√Hz Input-Referred Noise, 2dB to 18dB Gain Range,
0.125dB Gain Step Size
IIP3 = 23.7dBm at 2600MHz, 23.5dBm at 3600MHz, ICC = 82mA at 3.3V
10mA Supply Current, 10dBm IIP3, 10dB NF, Usable as Up- or Down-Converter.
22.9dBm OIP3 at 850MHz, –160.3dBm/Hz Noise Floor, 50Ω, 0.5VDC Baseband
Interface, 3-Ch CDMA2000 ACPR = –71.4dBc at 850MHz
21.7dBm OIP3 at 900MHz, –159dBm/Hz Noise Floor, High-Ohmic 0.5VDC
Baseband Interface
21.6dBm OIP3 at 2GHz, –158.6dBm/Hz Noise Floor, High-Ohmic 0.5VDC Baseband
Interface, 4-Ch W-CDMA ACPR = –67.7dBc at 2.14GHz
50Ω, Single-Ended RF and LO Ports, 28dBm IIP3 at 900MHz, 13.2dBm P1dB,
0.04dB I/Q Gain Mismatch, 0.4° I/Q Phase Mismatch
27.3dBm OIP3 at 2.14GHz, 9.9dB Noise Floor, 2.6dB Conversion Gain,
–35dBm LO Leakage
300MHz to 3GHz, Temperature Compensated, 2.7V to 6V Supply
100kHz to 1GHz, Temperature Compensated, 2.7V to 6V Supply
44dB Dynamic Range, Temperature Compensated, SC70 Package
36dB Dynamic Range, Low Power Consumption, SC70 Package
Precision VOUT Offset Control, Shutdown, Adjustable Gain
Precision VOUT Offset Control, Shutdown, Adjustable Offset
Precision VOUT Offset Control, Adjustable Gain and Offset
±1dB Output Variation over Temperature, 38ns Response Time, Log Linear
Response
25ns Response Time, Comparator Reference Input, Latch Enable Input,
–26dBm to +12dBm Input Range
Low Frequency to 1GHz, 83dB Log Linear Dynamic Range
75dB Dynamic Range, ±1dB Output Variation Over Temperature
Fast Responding, up to 60dB Dynamic Range, ±0.3dB Accuracy Over Temperature
10MHz to 6GHz, ±1dB Accuracy Over Temperature, 1.4mA at 3.3V Supply
5598f
16 Linear Technology Corporation
LT 0509 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2009