STEVAL-IFP030V1 High speed digital input current limiter evaluation board based on SCLT3-8BQ7 Data brief Description This evaluation board implements an 8-line protected digital input termination with serialized state transfer for Programmable Logic Controllers. It is based on the SCLT3-8BQ7 device. The SCLT3-8BQ7 enhances the I/O module density by cutting the dissipation (78 mW per input) and reducing the opto-transistor count. An adjustable digital filter and an LED driver are embedded in each input section. Its 2 MHz SPI peripheral output serializes the input state transfer to the I/O module controller. Features 8 inputs - 8-bit SPI output High side input with common ground 5 V voltage regulator Package: QFN 7 x 7 - 48L 30 V reverse polarity capable Adjustable current limiters LED output for visual status Optional 16-bit mode with parity check, temperature and voltage alarms Daisy chain capable Input digital filter with adjustable 20 to 160 µs delay Power dissipation 78 mW per channel RoHS compliant December 2015 The STEVAL-IFP030V1 evaluation board illustrates the flexibility of the SCTL3-8BQ7 with: 8/16-bit mode with parity check, temperature and voltage alarms; daisy-chain capability; adjustable digital minimal filter time (20 µs /160 µs). The STEVAL-IFP030V1 evaluation board can be chained with many other STEVAL-IFP030V1 evaluation boards. The adapter board can be placed between the first STEVAL-IFP030V1 evaluation board of the chain and the STEVAL-PCC009V2 STM32x microcontroller evaluation board. This adapter provides 2 buses: isolated and non-isolated. DocID028760 Rev 1 For further information contact your local STMicroelectronics sales office 1/5 www.st.com 2/5 GND JP1 JP3 JP2 Vcc DocID028760 Rev 1 GND 33nF C8 1.0K R10 (Left Side) GND R12 51K VC U1 MPT 0.5/10-2.54 Vcc INPUT7 VCS GND IN0 IN1 IN2 IN3 IN4 IN5 IN6 IN7 SPM DVR 1.5M 2 R9 120K DVR JMP1 GND 12 11 9 10 8 6 5 31 20 15 7 24 23 22 21 19 18 17 16 14 4 13 3 1K2 GND TAB 49 VDD /CS SCK MOSI /MISO MISO REF LD1 LD2 LD3 LD4 LD5 LD6 LD7 LD8 COMS NC NC NC NC NC NC NC NC SCLT3-8BQ7 DVR OSC SPM VC VCS IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 COMP COMP COMP COMP NC NC NC NC NC NC NC U1 GND 25 26 27 28 29 30 32 33 43 34 35 36 37 38 39 40 41 42 44 45 46 47 48 1 8 Steps 64 Steps R7 R6 9 10 8 6 7 INPUT6 INPUT5 INPUT3 INPUT1 INPUT4 VDD 2.2K IN3 R3 MISO /CS SCK GND VDD GND 1K2 JMP3 R11 Off LED6 LED4 LED2 GND VDD GND MOSI LED7 Green LED5 Green LED3 Green LED1 Green 16 bits 8 bits GND Active 15K LED0 1K2 JMP2 C7 C6 C5 STEVAL-IFP030V1 SPM 2.2K IN7 2.2K IN6 2.2K IN5 C4 C3 2.2K IN2 R2 2.2K IN4 C2 2.2K IN1 R4 JP0 R5 R8 JP4 VCS JP5 4 5 JP6 3 Vcc JP7 INPUT2 2 1 C0 C1 2.2K IN0 R0 R1 Green Green Green Green MISO MISO MOSI /CS /CS /CS GND VDD Vcc GND GND 1 2 3 4 5 J2 J1 (Right Side) Connectable to Adapter board (Top Side) Connectable for Daisy Chain J3 SCR4 SCR3 F2 F1 Fid ucia l F4 F3 (Bottom Side) Connectable for Daisy Chain BG303-05-A-0300-L-G 1 2 3 4 5 BG303-05-A-0300-L-G 1 3 2 4 5 BG302-05-A-L-G Mechanical SCR2 SCR1 Miscellaneous GND SCK SCK SCK Vcc 1 INP UT 0 CN1 Vcc Schematic diagram STEVAL-IFP030V1 Schematic diagram Figure 1: SCLT3-8BQ7 circuit schematic GSPG1412151150SG STEVAL-IFP030V1 2 Ordering information Ordering information To order the PLC digital input kit based on SCLT3-8BQ7, use the order codes STEVALIFP030V1 and STEVAL-PCC009V2. DocID028760 Rev 1 3/5 Revision history 3 STEVAL-IFP030V1 Revision history Table 1: Document revision history 4/5 Date Version Changes 17-Dec-2015 1 Initial release. DocID028760 Rev 1 STEVAL-IFP030V1 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved DocID028760 Rev 1 5/5