LTC2420 - 20-Bit µPower No Latency Delta-Sigma ADC in SO-8

LTC2420
20-Bit µPower
No Latency ∆Σ ADC in SO-8
TM
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
■
■
DESCRIPTIO
20-Bit ADC in SO-8 Package
8ppm INL, No Missing Codes at 20 Bits
4ppm Full-Scale Error
0.5ppm Offset
1.2ppm Noise
Digital Filter Settles in a Single Cycle. Each
Conversion Is Accurate, Even After an Input Step
Fast Mode: 16-Bit Noise, 12 Bits TUE at 100sps
Internal Oscillator—No External Components
Required
110dB Min, 50Hz/60Hz Notch Filter
Reference Input Voltage: 0.1V to VCC
Live Zero—Extended Input Range Accommodates
12.5% Overrange and Underrange
Single Supply 2.7V to 5.5V Operation
Low Supply Current (200µA) and Auto Shutdown
Pin Compatible with 24-Bit LTC2400
The LTC®2420 is a micropower 20-bit A/D converter with
an integrated oscillator, 8ppm INL and 1.2ppm RMS
noise that operates from 2.7V to 5.5V. It uses delta-sigma
technology and provides a digital filter that settles in a
single cycle for multiplexed applications. Through a single
pin, the LTC2420 can be configured for better than 110dB
rejection at 50Hz or 60Hz ±2%, or it can be driven by an
external oscillator for a user-defined rejection frequency
in the range 1Hz to 800Hz. The internal oscillator requires
no external frequency setting components.
Weight Scales
Direct Temperature Measurement
Gas Analyzers
Strain Gauge Transducers
Instrumentation
Data Acquisition
Industrial Process Control
4-Digit DVMs
, LTC and LT are registered trademarks of Linear Technology Corporation.
No Latency ∆Σ is a trademark of Linear Technology Corporation.
MICROWIRE is a trademark of National Semiconductor Corporation.
U
APPLICATIO S
■
■
■
■
■
■
■
The LTC2420 communicates through a flexible 3-wire
digital interface which is compatible with SPI and
MICROWIRETM protocols.
U
■
The converter accepts any external reference voltage from
0.1V to VCC. With its extended input conversion range of
–12.5% VREF to 112.5% VREF, the LTC2420 smoothly
resolves the offset and overrange problems of preceding
sensors or signal conditioning circuits.
Total Unadjusted Error (3V Supply)
TYPICAL APPLICATIO
10
VCC = 3V
VREF = 2.5V
8
2.7V TO 5.5V
6
VCC
1
VCC
FO
8
= INTERNAL OSC/50Hz REJECTION
= EXTERNAL CLOCK SOURCE
= INTERNAL OSC/60Hz REJECTION
LTC2420
REFERENCE
VOLTAGE
0.1V TO VCC
ANALOG
INPUT RANGE
–0.12VREF TO 1.12VREF
2
VREF
SCK
7
4
ERROR (ppm)
1µF
2
0
–2
–4
3
4
VIN
GND
SDO
CS
6
3-WIRE
SPI INTERFACE
TA = –55°C, –45°C, 25°C, 90°C
–6
–8
5
–10
2420 TA01
0
0.5
1.5
2.0
1.0
INPUT VOLTAGE (V)
2.5
2420 G01
1
LTC2420
U
W W
W
ABSOLUTE MAXIMUM RATINGS
U
W
U
PACKAGE/ORDER INFORMATION
(Notes 1, 2)
Supply Voltage (VCC) to GND .......................– 0.3V to 7V
Analog Input Voltage to GND ....... – 0.3V to (VCC + 0.3V)
Reference Input Voltage to GND .. – 0.3V to (VCC + 0.3V)
Digital Input Voltage to GND ........ – 0.3V to (VCC + 0.3V)
Digital Output Voltage to GND ..... – 0.3V to (VCC + 0.3V)
Operating Temperature Range
LTC2420C ............................................... 0°C to 70°C
LTC2420I ............................................ – 40°C to 85°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART NUMBER
TOP VIEW
VCC 1
8
FO
VREF 2
7
SCK
VIN 3
6
SDO
GND 4
5
CS
LTC2420CS8
LTC2420IS8
S8 PART MARKING
S8 PACKAGE
8-LEAD PLASTIC SO
2420
2420I
TJMAX = 125°C, θJA = 130°C/W
Consult factory for Military grade parts.
U
CONVERTER CHARACTERISTICS The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
4
8
10
20
ppm of VREF
ppm of VREF
Resolution (No Missing Codes)
0.1V ≤ VREF ≤ VCC, (Note 5)
●
Integral Nonlinearity
VREF = 2.5V (Note 6)
VREF = 5V (Note 6)
●
●
Integral Nonlinearity (Fast Mode)
VREF = 5V, VREF = 2.5V, 100 Samples/Second, fO = 2.048MHz
●
40
250
ppm of VREF
Offset Error
2.5V ≤ VREF ≤ VCC
●
0.5
10
ppm of VREF
Offset Error (Fast Mode)
2.5V < VREF < 5V, 100 Samples/Second, fO = 2.048MHz
Offset Error Drift
2.5V ≤ VREF ≤ VCC
Full-Scale Error
2.5V ≤ VREF ≤ VCC
Full-Scale Error (Fast Mode)
2.5V < VREF < 5V, 100 Samples/Second, fO = 2.048MHz
20
Bits
3
ppm of VREF
0.04
4
●
10
ppm of VREF/°C
10
ppm of VREF
ppm of VREF
Full-Scale Error Drift
2.5V ≤ VREF ≤ VCC
Total Unadjusted Error
VREF = 2.5V
VREF = 5V
Output Noise
VIN = 0V (Note 13)
6
µVRMS
Output Noise (Fast Mode)
VREF = 5V, 100 Samples/Second, fO = 2.048MHz
20
µVRMS
Normal Mode Rejection 60Hz ±2%
(Note 7)
●
110
130
dB
Normal Mode Rejection 50Hz ±2%
(Note 8)
●
110
130
dB
Power Supply Rejection, DC
VREF = 2.5V, VIN = 0V
100
dB
Power Supply Rejection, 60Hz ±2%
VREF = 2.5V, VIN = 0V, (Notes 7, 15)
110
dB
Power Supply Rejection, 50Hz ±2%
VREF = 2.5V, VIN = 0V, (Notes 8, 15)
110
dB
2
0.04
8
16
ppm of VREF/°C
ppm of VREF
ppm of VREF
LTC2420
U
U
U
U
A ALOG I PUT A D REFERE CE
The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
VIN
Input Voltage Range
(Note 14)
VREF
Reference Voltage Range
CS(IN)
Input Sampling Capacitance
CS(REF)
Reference Sampling Capacitance
IIN(LEAK)
Input Leakage Current
CS = VCC
●
– 100
1
100
nA
IREF(LEAK)
Reference Leakage Current
VREF = 2.5V, CS = VCC
●
– 100
1
100
nA
●
– 0.125 • VREF
●
0.1
TYP
MAX
UNITS
1.125 • VREF
V
VCC
V
1
pF
1.5
pF
U
U
DIGITAL I PUTS A D DIGITAL OUTPUTS
The ● denotes specifications which apply over the full
operating temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
VIH
High Level Input Voltage
CS, FO
2.7V ≤ VCC ≤ 5.5V
2.7V ≤ VCC ≤ 3.3V
●
MIN
VIL
Low Level Input Voltage
CS, FO
4.5V ≤ VCC ≤ 5.5V
2.7V ≤ VCC ≤ 5.5V
●
VIH
High Level Input Voltage
SCK
2.7V ≤ VCC ≤ 5.5V (Note 9)
2.7V ≤ VCC ≤ 3.3V (Note 9)
●
VIL
Low Level Input Voltage
SCK
4.5V ≤ VCC ≤ 5.5V (Note 9)
2.7V ≤ VCC ≤ 5.5V (Note 9)
●
IIN
Digital Input Current
CS, FO
0V ≤ VIN ≤ VCC
●
IIN
Digital Input Current
SCK
0V ≤ VIN ≤ VCC (Note 9)
●
CIN
Digital Input Capacitance
CS, FO
CIN
Digital Input Capacitance
SCK
(Note 9)
VOH
High Level Output Voltage
SDO
IO = – 800µA
●
VOL
Low Level Output Voltage
SDO
IO = 1.6mA
●
VOH
High Level Output Voltage
SCK
IO = – 800µA (Note 10)
●
VOL
Low Level Output Voltage
SCK
IO = 1.6mA (Note 10)
●
IOZ
High-Z Output Leakage
SDO
●
TYP
MAX
UNITS
2.5
2.0
V
V
0.8
0.6
V
V
2.5
2.0
V
V
0.8
0.6
V
V
–10
10
µA
–10
10
µA
10
pF
10
pF
VCC – 0.5
V
0.4
V
VCC – 0.5
V
–10
0.4
V
10
µA
U W
POWER REQUIRE E TS
The ● denotes specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
VCC
Supply Voltage
ICC
Supply Current
Conversion Mode
Sleep Mode
CONDITIONS
MIN
●
CS = 0V (Note 12)
CS = VCC (Note 12)
●
●
TYP
2.7
200
20
MAX
UNITS
5.5
V
300
30
µA
µA
3
LTC2420
WU
TI I G CHARACTERISTICS
The ● denotes specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
fEOSC
External Oscillator Frequency Range
20-Bit Effective Resolution
12-Bit Effective Resolution
tHEO
TYP
MAX
UNITS
kHz
MHz
●
●
2.56
2.56
307.2
2.048
External Oscillator High Period
●
0.2
390
µs
tLEO
External Oscillator Low Period
●
0.2
390
µs
tCONV
Conversion Time
FO = 0V
FO = VCC
External Oscillator (Note 11)
fISCK
Internal SCK Frequency
Internal Oscillator (Note 10)
External Oscillator (Notes 10, 11)
DISCK
Internal SCK Duty Cycle
(Note 10)
fESCK
External SCK Frequency Range
(Note 9)
●
tLESCK
External SCK Low Period
(Note 9)
●
250
ns
tHESCK
External SCK High Period
(Note 9)
●
250
ns
tDOUT_ISCK
Internal SCK 24-Bit Data Output Time
Internal Oscillator (Notes 10, 12)
External Oscillator (Notes 10, 11)
●
●
1.23
tDOUT_ESCK
External SCK 24-Bit Data Output Time
(Note 9)
●
t1
CS ↓ to SDO Low Z
t2
CS ↑ to SDO High Z
t3
CS ↓ to SCK ↓
(Note 10)
t4
CS ↓ to SCK ↑
(Note 9)
tKQMAX
SCK ↓ to SDO Valid
tKQMIN
SDO Hold After SCK ↓
t5
t6
130.86
133.53
136.20
157.03
160.23
163.44
20510/fEOSC (in kHz)
19.2
fEOSC/8
45
ms
ms
ms
kHz
kHz
55
%
2000
kHz
1.25
1.28
192/fEOSC (in kHz)
ms
ms
24/fESCK (in kHz)
ms
●
0
150
ns
●
0
150
ns
●
0
150
ns
●
50
ns
200
●
(Note 5)
●
15
SCK Set-Up Before CS ↓
●
50
SCK Hold After CS ↓
●
Note 1: Absolute Maximum Ratings are those values beyond which the
life of the device may be impaired.
Note 2: All voltage values are with respect to GND.
Note 3: All voltages are with respect to GND. VCC = 2.7 to 5.5V unless
otherwise specified. RSOURCE = 0Ω.
Note 4: Internal Conversion Clock source with the FO pin tied
to GND or to VCC or to external conversion clock source with
fEOSC = 153600Hz unless otherwise specified.
Note 5: Guaranteed by design, not subject to test.
Note 6: Integral nonlinearity is defined as the deviation of a code from
a straight line passing through the actual endpoints of the transfer
curve. The deviation is measured from the center of the quantization
band.
Note 7: FO = 0V (internal oscillator) or fEOSC = 153600Hz ±2%
(external oscillator).
Note 8: FO = VCC (internal oscillator) or fEOSC = 128000Hz ±2%
(external oscillator).
4
●
●
●
ns
ns
ns
50
ns
Note 9: The converter is in external SCK mode of operation such that
the SCK pin is used as digital input. The frequency of the clock signal
driving SCK during the data output is fESCK and is expressed in kHz.
Note 10: The converter is in internal SCK mode of operation such that
the SCK pin is used as digital output. In this mode of operation the
SCK pin has a total equivalent load capacitance CLOAD = 20pF.
Note 11: The external oscillator is connected to the FO pin. The external
oscillator frequency, fEOSC, is expressed in kHz.
Note 12: The converter uses the internal oscillator.
FO = 0V or FO = VCC.
Note 13: The output noise includes the contribution of the internal
calibration operations.
Note 14: For reference voltage values VREF > 2.5V the extended input
of – 0.125 • VREF to 1.125 • VREF is limited by the absolute maximum
rating of the Analog Input Voltage pin (Pin 3). For 2.5V < VREF ≤
0.267V + 0.89 • VCC the input voltage range is – 0.3V to 1.125 • VREF.
For 0.267V + 0.89 • VCC < VREF ≤ VCC the input voltage range is – 0.3V
to VCC + 0.3V.
Note 15: VCC (DC) = 4.1V, VCC (AC) = 2.8VP-P.
LTC2420
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Total Unadjusted Error (3V Supply)
10
10
VCC = 3V
VREF = 2.5V
8
6
4
4
4
2
–2
–4
ERROR (ppm)
6
0
2
0
–2
TA = –55°C, –45°C, 25°C, 90°C
–6
–8
–10
2.5
0.5
0
1.5
2.0
1.0
INPUT VOLTAGE (V)
6
4
4
–2
–4
2
0
–2
–4
TA = –55°C, –45°C, 25°C, 90°C
–6
ERROR (ppm)
6
4
0
–8
2.60 2.65 2.70
INPUT VOLTAGE (V)
2.75
–10
2.80
1
0
3
2
INPUT VOLTAGE (V)
4
2420 G04
VCC = 5V
VREF = 5V
8
6
4
10
8
VCC = 5V
VREF = 5V
ERROR (ppm)
2
–2
–4
–6
–6
–8
–8
–0.05 –0.10 –0.15 –0.20 –0.25 –0.30
INPUT VOLTAGE (V)
2420 G07
4
–10
5.00
5
VCC = 5V
TA = 25°C
120
0
–4
–10
3
2
INPUT VOLTAGE (V)
Offset Error vs Reference Voltage
4
TA = –55°C
–2
1
150
6
0
0
2420 G06
Positive Input Extended Total
Unadjusted Error (5V Supply)
TA = 25°C
TA = 90°C
TA = –45°C
2
0
–10
5
2420 G05
Negative Input Extended Total
Unadjusted Error (5V Supply)
10
TA = –55°C, –45°C, 25°C, 90°C
–8
TA = –55°C
TA = 90°C
TA = 25°C
OFFSET ERROR (ppm)
2.55
–2
–6
–8
–10
2.50
2
0
–4
TA = –55°C, –45°C, 25°C, 90°C
–6
VCC = 5V
VREF = 5V
8
6
ERROR (ppm)
ERROR (ppm)
INL (5V Supply)
10
VCC = 5V
VREF = 5V
8
2
–0.05 –0.10 –0.15 –0.20 –0.25 –0.30
INPUT VOLTAGE (V)
2420 G03
Total Unadjusted Error (5V Supply)
10
VCC = 3V
VREF = 2.5V
8
0
2.5
2420 G02
Positive Input Extended Total
Unadjusted Error (3V Supply)
10
TA = –55°C
–6
–10
2420 G01
ERROR (ppm)
0
–10
1.5
2.0
1.0
INPUT VOLTAGE (V)
TA = –45°C
–2
–8
0.5
TA = 25°C
2
–8
0
TA = 90°C
–4
–4
TA = –55°C, –45°C, 25°C, 90°C
–6
VCC = 3V
VREF = 2.5V
8
6
ERROR (ppm)
ERROR (ppm)
10
VCC = 3V
VREF = 2.5V
8
Negative Input Extended Total
Unadjusted Error (3V Supply)
INL (3V Supply)
90
60
30
TA = –45°C
0
5.05
5.10 5.15 5.20
INPUT VOLTAGE (V)
5.25
5.30
2420 G08
0
1
3
4
2
REFERENCE VOLTAGE (V)
5
2420 G09
5
LTC2420
U W
TYPICAL PERFOR A CE CHARACTERISTICS
RMS Noise vs Reference Voltage
60
VCC = 5V
TA = 25°C
30
20
VREF = 2.5V
TA = 25°C
7.5
5
RMS NOISE (ppm)
OFFSET ERROR (ppm)
40
10.0
VREF = 2.5V
TA = 25°C
50
RMS NOISE (ppm OF VREF)
RMS Noise vs VCC
Offset Error vs VCC
10
0
5.0
2.5
–5
10
0
–10
0
0
1
2.7
5
2
3
4
REFERENCE VOLTAGE (V)
3.2
3.7
4.2
VCC (V)
2420 G10
Noise Histogram
VCC = 5V
VREF = 5V
VIN = 0.3V TO 5.3V
TA = 25°C
3.75
RMS NOISE (ppm)
150
100
4.2
VCC (V)
4.7
5.2 5.5
Offset Error vs Temperature
10
OFFSET ERROR (ppm)
VCC = 5
=5
V
300 VREF= 0
IN
200
3.7
2420 G12
RMS Noise vs Code Out
5.00
250
3.2
2420 G11
350
NUMBER OF READINGS
2.7
5.2 5.5
4.7
2.50
1.25
VCC = 5V
VREF = 5V
VIN = 0V
5
0
–5
50
0
0
–2
4
2
0
OUTPUT CODE (ppm)
6
0
7FFFFF
CODE OUT (HEX)
–5
FULL-SCALE ERROR (ppm)
FULL-SCALE ERROR (ppm)
FULL-SCALE ERROR (ppm)
10
–25
0
120
Full-Scale Error vs VCC
0
5
95
2420 G15
Full-Scale Error
vs Reference Voltage
Full-Scale Error vs Temperature
VCC = 5V
VREF = 5V
VIN = 5V
70
–5
20
45
TEMPERATURE (°C)
2420 G14
2420G13
10
–10
–55 –30
FFFFFF
–50
–75
–100
VREF = 2.5V
VIN = 2.5V
TA = 25°C
5
0
–5
–125
–10
–55 –30
–150
70
–5
20
45
TEMPERATURE (°C)
95
120
2420 G16
6
VCC = 5V
VIN = VREF
0
1
2
3
4
REFERENCE VOLTAGE (V)
5
2420 G17
–10
2.7
3.2
3.7
4.2
VCC (V)
4.7
5.2 5.5
2420 G18
LTC2420
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Conversion Current
vs Temperature
230
220
–20
VCC = 4.1V
VIN = 0V
T = 25°C
–40 F A = 0
O
VCC = 5.5V
200
VCC = 4.1V
190
180
VCC = 2.7V
170
VCC = 2.7V
20
REJECTION (dB)
210
SUPPLY CURRENT (µA)
SUPPLY CURRENT (µA)
Rejection vs Frequency at VCC
Sleep Current vs Temperature
30
VCC = 5V
10
–60
–80
–100
160
150
– 55 –30
70
45
20
TEMPERATURE (°C)
–5
95
0
–55 –30
120
–5
20
45
70
TEMPERATURE (°C)
95
Rejection vs Frequency at VCC
–40
–40
–40
REJECTION (dB)
–20
REJECTION (dB)
REJECTION (dB)
VCC = 4.1V
VIN = 0V
–20 TA = 25°C
FO = 0
–60
–80
–100
–100
–120
15200 15250 15300 15350 15400 15450 15500
FREQUENCY AT VCC (Hz)
–120
–60
–80
–120
100
10k
FREQUENCY AT VCC (Hz)
2420 G22
1
1M
100
150
200
FREQUENCY AT VIN (Hz)
–70
–20
REJECTION (dB)
–80
Rejection vs Frequency at VIN
0
VCC = 5V
VREF = 5V
VIN = 2.5V
FO = 0
–20
–40
–40
REJECTION (dB)
–60
250
2420 G24
Rejection vs Frequency at VIN
–110
50
2420 G23
0
–100
VCC = 5V
VREF = 5V
VIN = 2.5V
FO = 0
–100
1
Rejection vs Frequency at VIN
250
Rejection vs Frequency at VIN
VCC = 4.1V
VIN = 0V
–20 TA = 25°C
FO = 0
–90
150
200
100
FREQUENCY AT VCC (Hz)
0
0
–80
50
2420 G21
Rejection vs Frequency at VCC
0
–60
1
2420 G20
2420 G19
REJECTION (dB)
–120
120
–60
–80
–60
–80
–100
–120
–100
–130
–120
SAMPLE RATE = 15.36kHz ± 2%
–140
–120
15100
–12
–8
–4
0
4
8
12
INPUT FREQUENCY DEVIATION FROM NOTCH FREQUENCY (%)
2420 G25
15200
15300
15400
FREQUENCY AT VIN (Hz)
15500
–140
0
fS/2
fS
INPUT FREQUENCY
2420 G26
2420 F27
7
LTC2420
U W
TYPICAL PERFOR A CE CHARACTERISTICS
VCC = 5V
VREF = 5V
FO = EXTERNAL
16
TA = –45°C
TA = 25°C
14
TA = 90°C
VCC = 5V
VREF = 5V
fO = EXTERNAL
TA = 25°C
TA = 90°C
TA = –45°C
22
16
TA = –45°C
14
TA = 25°C
TA = 90°C
20
18
12
12
10
Resolution vs Output Rate
24
VCC = 3V
VREF = 2.5V
FO = EXTERNAL
18
TUE RESOLUTION (BITS)
18
TUE RESOLUTION (BITS)
INL vs Output Rate
20
RESOLUTION (BITS)
INL vs Output Rate
20
10
0
10 20 30 40 50 60 70 80 90 100
OUTPUT RATE (Hz)
16
0
10 20 30 40 50 60 70 80 90 100
OUTPUT RATE (Hz)
2420 G28
2420 G29
0 7.5
25
75
50
OUTPUT RATE (Hz)
100
2420 G30
U
U
U
PIN FUNCTIONS
VCC (Pin 1): Positive Supply Voltage. Bypass to GND
(Pin␣ 4) with a 10µF tantalum capacitor in parallel with
0.1µF ceramic capacitor as close to the part as possible.
VREF (Pin 2): Reference Input. The reference voltage range
is 0.1V to VCC.
VIN (Pin 3): Analog Input. The input voltage range is
– 0.125 • VREF to 1.125 • VREF. For VREF > 2.5V the input
voltage range may be limited by the pin absolute maximum rating of – 0.3V to VCC + 0.3V.
GND (Pin 4): Ground. Shared pin for analog ground,
digital ground, reference ground and signal ground. Should
be connected directly to a ground plane through a minimum length trace or it should be the single-point-ground
in a single point grounding system.
CS (Pin 5): Active LOW Digital Input. A LOW on this pin
enables the SDO digital output and wakes up the ADC.
Following each conversion, the ADC automatically enters
the Sleep mode and remains in this low power state as
long as CS is HIGH. A LOW on CS wakes up the ADC. A
LOW-to-HIGH transition on this pin disables the SDO
digital output. A LOW-to-HIGH transition on CS during the
Data Output transfer aborts the data transfer and starts a
new conversion.
8
SDO (Pin 6): Three-State Digital Output. During the data
output period this pin is used for serial data output. When
the chip select CS is HIGH (CS = VCC), the SDO pin is in a
high impedance state. During the Conversion and Sleep
periods, this pin can be used as a conversion status output. The conversion status can be observed by pulling CS
LOW.
SCK (Pin 7): Bidirectional Digital Clock Pin. In Internal
Serial Clock Operation mode, SCK is used as digital output
for the internal serial interface clock during the data output
period. In External Serial Clock Operation mode, SCK is
used as digital input for the external serial interface. A
weak internal pull-up is automatically activated in Internal
Serial Clock Operation mode. The Serial Clock mode is
determined by the level applied to SCK at power up and the
falling edge of CS.
FO (Pin 8): Frequency Control Pin. Digital input that
controls the ADC’s notch frequencies and conversion
time. When the FO pin is connected to VCC (FO = VCC), the
converter uses its internal oscillator and the digital filter’s
first null is located at 50Hz. When the FO pin is connected
to GND (FO = OV), the converter uses its internal oscillator
and the digital filter first null is located at 60Hz. When FO
is driven by an external clock signal with a frequency fEOSC,
the converter uses this signal as its clock and the digital
filter first null is located at a frequency fEOSC/2560.
LTC2420
W
FU CTIO AL BLOCK DIAGRA
U
U
INTERNAL
OSCILLATOR
VCC
GND
VIN
AUTOCALIBRATION
AND CONTROL
∫
∫
FO
(INT/EXT)
∫
∑
SDO
SERIAL
INTERFACE
ADC
SCK
CS
VREF
DECIMATING FIR
DAC
2420 FD
TEST CIRCUITS
VCC
3.4k
SDO
SDO
3.4k
Hi-Z TO VOH
VOL TO VOH
VOH TO Hi-Z
CLOAD = 20pF
2420 TC01
CLOAD = 20pF
Hi-Z TO VOL
VOH TO VOL
VOL TO Hi-Z
2420 TC02
9
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
The LTC2420 is pin compatible with the LTC2400. The two
devices are designed to allow the user to incorporate
either device in the same design with no modifications.
While the LTC2420 output word length is 24 bits (as
opposed to the 32-bit output of the LTC2400), its output
clock timing can be identical to the LTC2400. As shown in
Figure 1, the LTC2420 data output is concluded on the
falling edge of the 24th serial clock (SCK). In order to
maintain drop-in compatibility with the LTC2400, it is
possible to clock the LTC2420 with an additional 8 serial
clock pulses. This results in 8 additional output bits which
are always logic HIGH.
Converter Operation Cycle
The LTC2420 is a low power, delta-sigma analog-todigital converter with an easy to use 3-wire serial interface.
Its operation is simple and made up of three states. The
converter operating cycle begins with the conversion,
followed by a low power sleep state and concluded with
the data output (see Figure 2). The 3-wire interface consists of serial data output (SDO), a serial clock (SCK) and
a chip select (CS).
Once CS is pulled LOW, the device begins outputting the
conversion result. There is no latency in the conversion
result. The data output corresponds to the conversion just
performed. This result is shifted out on the serial data out
pin (SDO) under the control of the serial clock (SCK). Data
is updated on the falling edge of SCK allowing the user to
reliably latch data on the rising edge of SCK, see Figure 4.
The data output state is concluded once 24 bits are read
out of the ADC or when CS is brought HIGH. The device
automatically initiates a new conversion cycle and the
cycle repeats.
Through timing control of the CS and SCK pins, the
LTC2420 offers several flexible modes of operation
(internal or external SCK and free-running conversion
modes). These various modes do not require
programming configuration registers; moreover, they do
CONVERT
SLEEP
Initially, the LTC2420 performs a conversion. Once the
conversion is complete, the device enters the sleep state.
While in this sleep state, power consumption is reduced by
an order of magnitude. The part remains in the sleep state
as long as CS is logic HIGH. The conversion result is held
indefinitely in a static shift register while the converter is
in the sleep state.
1
CS AND
SCK
0
DATA OUTPUT
2420 F02
Figure 2. LTC2420 State Transition Diagram
CS
8
8
8
8 (OPTIONAL)
SCK
SDO
EOC = 1
EOC = 0
DATA OUT
4 STATUS BITS 20 DATA BITS
CONVERSION
SLEEP
DATA OUTPUT
EOC = 1
LAST 8 BITS ALWAYS 1
CONVERSION
2420 F01
Figure 1. LTC2420 Compatible Timing with the LTC2400
10
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
not disturb the cyclic operation described above. These
modes of operation are described in detail in the Serial
Interface Timing Modes section.
Conversion Clock
A major advantage delta-sigma converters offer over
conventional type converters is an on-chip digital filter
(commonly known as Sinc or Comb filter). For high
resolution, low frequency applications, this filter is typically designed to reject line frequencies of 50Hz or 60Hz
plus their harmonics. In order to reject these frequencies
in excess of 110dB, a highly accurate conversion clock is
required. The LTC2420 incorporates an on-chip highly
accurate oscillator. This eliminates the need for external
frequency setting components such as crystals or oscillators. Clocked by the on-chip oscillator, the LTC2420
rejects line frequencies (50Hz or 60Hz ±2%) a minimum
of 110dB.
Ease of Use
The LTC2420 data output has no latency, filter settling or
redundant data associated with the conversion cycle.
There is a one-to-one correspondence between the
conversion and the output data. Therefore, multiplexing
an analog input voltage is easy.
The LTC2420 performs offset and full-scale calibrations
every conversion cycle. This calibration is transparent to
the user and has no effect on the cyclic operation described above. The advantage of continuous calibration is
extreme stability of offset and full-scale readings with respect to time, supply voltage change and temperature drift.
Power-Up Sequence
The LTC2420 automatically enters an internal reset state
when the power supply voltage VCC drops below approximately 2.2V. This feature guarantees the integrity of the
conversion result and of the serial interface mode selection which is performed at the initial power-up. (See the
2-wire I/O sections in the Serial Interface Timing Modes
section.)
When the VCC voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signal with duration of approximately 0.5ms. The POR
signal clears all internal registers. Following the POR
signal, the LTC2420 starts a normal conversion cycle and
follows the normal succession of states described above.
The first conversion result following POR is accurate
within the specifications of the device.
Reference Voltage Range
The LTC2420 can accept a reference voltage from 0V to
VCC. The converter output noise is determined by the
thermal noise of the front-end circuits, and as such, its
value in microvolts is nearly constant with reference
voltage. A decrease in reference voltage will not significantly improve the converter’s effective resolution. On the
other hand, a reduced reference voltage will improve the
overall converter INL performance. The recommended
range for the LTC2420 voltage reference is 100mV to VCC.
Input Voltage Range
The converter is able to accommodate system level offset
and gain errors as well as system level overrange situations due to its extended input range, see Figure 3. The
LTC2420 converts input signals within the extended input
range of – 0.125 • VREF to 1.125 • VREF.
For large values of VREF, this range is limited by the
absolute maximum voltage range of – 0.3V to (VCC + 0.3V).
Beyond this range, the input ESD protection devices begin
to turn on and the errors due to the input leakage current
increase rapidly.
Input signals applied to VIN may extend below ground by
– 300mV and above VCC by 300mV. In order to limit any
VCC + 0.3V
9/8VREF
VREF
1/2VREF
NORMAL
INPUT
RANGE
EXTENDED
INPUT
RANGE
ABSOLUTE
MAXIMUM
INPUT
RANGE
0
–1/8VREF
–0.3V
2420 F03
Figure 3. LTC2420 Input Range
11
LTC2420
U
U
W
U
APPLICATIO S I FOR ATIO
fault current, a resistor of up to 25k may be added in series
with the VIN pin without affecting the performance of the
device. In the physical layout, it is important to maintain
the parasitic capacitance of the connection between this
series resistance and the VIN pin as low as possible;
therefore, the resistor should be located as close as
practical to the VIN pin. The effect of the series resistance
on the converter accuracy can be evaluated from the
curves presented in the Analog Input/Reference Current
section. In addition, a series resistor will introduce a
temperature dependent offset error due to the input leakage current. A 1nA input leakage current will develop a
1ppm offset error on a 5k resistor if VREF = 5V. This error
has a very strong temperature dependency.
Bit 20 (fourth output bit) is the extended input range (EXR)
indicator. If the input is within the normal input range
0␣ ≤␣ VIN ≤ VREF, this bit is LOW. If the input is outside the
normal input range, VIN > VREF or VIN < 0, this bit is HIGH.
The function of these bits is summarized in Table 1.
Table 1. LTC2420 Status Bits
Bit 23
EOC
Bit 22
DMY
Bit 21
SIG
Bit 20
EXR
VIN > VREF
0
0
1
1
0 < VIN ≤ VREF
0
0
1
0
VIN = 0+/0 –
0
0
1/0
0
VIN < 0
0
0
0
1
Input Range
Bit 19 (fifth output bit) is the most significant bit (MSB).
Output Data Format
Bits 19-0 are the 20-bit conversion result MSB first.
The LTC2420 serial output data stream is 24 bits long. The
first 4 bits represent status information indicating the
sign, input range and conversion state. The next 20 bits are
the conversion result, MSB first.
Bit 0 is the least significant bit (LSB).
Bit 23 (first output bit) is the end of conversion (EOC)
indicator. This bit is available at the SDO pin during the
conversion and sleep states whenever the CS pin is LOW.
This bit is HIGH during the conversion and goes LOW
when the conversion is complete.
Bit 22 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit 21 (third output bit) is the conversion result sign indicator (SIG). If VIN is >0, this bit is HIGH. If VIN is <0, this
bit is LOW. The sign bit changes state during the zero code.
Data is shifted out of the SDO pin under control of the serial
clock (SCK), see Figure 4. Whenever CS is HIGH, SDO
remains high impedance and any SCK clock pulses are
ignored by the internal data out shift register.
In order to shift the conversion result out of the device, CS
must first be driven LOW. EOC is seen at the SDO pin of the
device once CS is pulled LOW. EOC changes real time from
HIGH to LOW at the completion of a conversion. This
signal may be used as an interrupt for an external microcontroller. Bit 23 (EOC) can be captured on the first rising
edge of SCK. Bit 22 is shifted out of the device on the first
falling edge of SCK. The final data bit (Bit 0) is shifted out
on the falling edge of the 23rd SCK and may be latched on
CS
SDO
BIT 23
BIT 22
BIT 21
BIT 20
BIT 19
EOC
“0”
SIG
EXT
MSB
BIT 4
BIT 0
LSB20
Hi-Z
SCK
1
SLEEP
2
3
4
5
DATA OUTPUT
19
20
24
CONVERSION
2420 F04
Figure 4. Output Data Timing
12
LTC2420
U
U
W
U
APPLICATIO S I FOR ATIO
the rising edge of the 24th SCK pulse. On the falling edge
of the 24th SCK pulse, SDO goes HIGH indicating a new
conversion cycle has been initiated. This bit serves as EOC
(Bit 23) for the next conversion cycle. Table 2 summarizes
the output data format.
change during the sleep or data output states will not
disturb the converter operation. If the selection is made
during the conversion state, the result of the conversion in
progress may be outside specifications but the following
conversions will not be affected.
As long as the voltage on the VIN pin is maintained within
the – 0.3V to (VCC + 0.3V) absolute maximum operating
range, a conversion result is generated for any input value
from – 0.125 • VREF to 1.125 • VREF. For input voltages
greater than 1.125 • VREF, the conversion result is clamped
to the value corresponding to 1.125 • VREF. For input
voltages below – 0.125 • VREF, the conversion result is
clamped to the value corresponding to – 0.125 • VREF.
When a fundamental rejection frequency different from
50Hz or 60Hz is required or when the converter must be
synchronized with an outside source, the LTC2420 can
operate with an external conversion clock. The converter
automatically detects the presence of an external clock
signal at the FO pin and turns off the internal oscillator. The
frequency fEOSC of the external signal must be at least
2560Hz (1Hz notch frequency) to be detected. The external clock signal duty cycle is not significant as long as the
minimum and maximum specifications for the high and
low periods tHEO and tLEO are observed.
Frequency Rejection Selection (FO Pin Connection)
The LTC2420 internal oscillator provides better than 110dB
normal mode rejection at the line frequency and its harmonics for 50Hz ±2% or 60Hz ±2%. For 60Hz rejection, FO
(Pin 8) should be connected to GND (Pin 4) while for 50Hz
rejection the FO pin should be connected to VCC (Pin␣ 1).
While operating with an external conversion clock of a
frequency fEOSC, the LTC2420 provides better than 110dB
normal mode rejection in a frequency range fEOSC/2560
±4% and its harmonics. The normal mode rejection as a
function of the input frequency deviation from fEOSC/2560
is shown in Figure 5.
The selection of 50Hz or 60Hz rejection can also be made
by driving FO to an appropriate logic level. A selection
Table 2. LTC2420 Output Data Format
Bit 23
EOC
Bit 22
DMY
Bit 21
SIG
Bit 20
EXR
Bit 19
MSB
Bit 18
Bit 17
Bit 16
Bit 15
…
Bit 0
LSB
VIN > 9/8 • VREF
0
0
1
1
0
0
0
1
1
...
1
9/8 • VREF
0
0
1
1
0
0
0
1
1
...
1
VREF + 1LSB
0
0
1
1
0
0
0
0
0
...
0
VREF
0
0
1
0
1
1
1
1
1
...
1
3/4VREF + 1LSB
0
0
1
0
1
1
0
0
0
...
0
3/4VREF
0
0
1
0
1
0
1
1
1
...
1
Input Voltage
1/2VREF + 1LSB
0
0
1
0
1
0
0
0
0
...
0
1/2VREF
0
0
1
0
0
1
1
1
1
...
1
1/4VREF + 1LSB
0
0
1
0
0
1
0
0
0
...
0
1/4VREF
0
0
1
0
0
0
1
1
1
...
1
0+/0 –
0
0
1/0*
0
0
0
0
0
0
...
0
–1LSB
0
0
0
1
1
1
1
1
1
...
1
–1/8 • VREF
0
0
0
1
1
1
1
0
0
...
0
VIN < –1/8 • VREF
0
0
0
1
1
1
1
0
0
...
0
*The sign bit changes state during the 0 code.
13
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
–60
Table 3 summarizes the duration of each state as a
function of FO.
–70
REJECTION (dB)
–80
SERIAL INTERFACE
–90
–100
–110
–120
–130
–140
–12
–8
–4
0
4
8
12
INPUT FREQUENCY DEVIATION FROM NOTCH FREQUENCY (%)
2420 F05
Figure 5. LTC2420 Normal Mode Rejection When
Using an External Oscillator of Frequency fEOSC
Whenever an external clock is not present at the FO pin, the
converter automatically activates its internal oscillator and
enters the Internal Conversion Clock mode. The LTC2420
operation will not be disturbed if the change of conversion
clock source occurs during the sleep state or during the
data output state while the converter uses an external
serial clock. If the change occurs during the conversion
state, the result of the conversion in progress may be
outside specifications but the following conversions will
not be affected. If the change occurs during the data output
state and the converter is in the Internal SCK mode, the
serial clock duty cycle may be affected but the serial data
stream will remain valid.
The LTC2420 transmits the conversion results and receives the start of conversion command through a synchronous 3-wire interface. During the conversion and
sleep states, this interface can be used to assess the
converter status and during the data output state it is used
to read the conversion result.
Serial Clock Input/Output (SCK)
The serial clock signal present on SCK (Pin 7) is used to
synchronize the data transfer. Each bit of data is shifted out
the SDO pin on the falling edge of the serial clock.
In the Internal SCK mode of operation, the SCK pin is an
output and the LTC2420 creates its own serial clock by
dividing the internal conversion clock by 8. In the External
SCK mode of operation, the SCK pin is used as input. The
internal or external SCK mode is selected on power-up and
then reselected every time a HIGH-to-LOW transition is
detected at the CS pin. If SCK is HIGH or floating at powerup or during this transition, the converter enters the internal SCK mode. If SCK is LOW at power-up or during this
transition, the converter enters the external SCK mode.
Table 3. LTC2420 State Duration
State
Operating Mode
CONVERT
Internal Oscillator
External Oscillator
Duration
FO = LOW
(60Hz Rejection)
133ms
FO = HIGH
(50Hz Rejection)
160ms
FO = External Oscillator
with Frequency fEOSC kHz
(fEOSC/2560 Rejection)
20510/fEOSCs
SLEEP
DATA OUTPUT
As Long As CS = HIGH Until CS = 0 and SCK
Internal Serial Clock
External Serial Clock with
Frequency fSCK kHz
14
FO = LOW/HIGH
(Internal Oscillator)
As Long As CS = LOW But Not Longer Than 1.26ms
(24 SCK cycles)
FO = External Oscillator with
Frequency fEOSC kHz
As Long As CS = LOW But Not Longer Than 256/fEOSCms
(24 SCK cycles)
As Long As CS = LOW But Not Longer Than 24/fSCKms
(24 SCK cycles)
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
Serial Data Output (SDO)
SERIAL INTERFACE TIMING MODES
The serial data output pin, SDO (Pin 6), drives the serial
data during the data output state. In addition, the SDO pin
is used as an end of conversion indicator during the
conversion and sleep states.
The LTC2420’s 3-wire interface is SPI and MICROWIRE
compatible. This interface offers several flexible modes of
operation. These include internal/external serial clock,
2- or 3-wire I/O, single cycle conversion and autostart. The
following sections describe each of these serial interface
timing modes in detail. In all these cases, the converter
can use the internal oscillator (FO = LOW or FO = HIGH) or
an external oscillator connected to the FO pin. Refer to
Table 4 for a summary.
When CS (Pin 5) is HIGH, the SDO driver is switched to a
high impedance state. This allows sharing the serial
interface with other devices. If CS is LOW during the
convert or sleep state, SDO will output EOC. If CS is LOW
during the conversion phase, the EOC bit appears HIGH on
the SDO pin. Once the conversion is complete, EOC goes
LOW. The device remains in the sleep state until the first
rising edge of SCK occurs while CS is LOW.
Chip Select Input (CS)
The active LOW chip select, CS (Pin 5), is used to test the
conversion status and to enable the data output transfer as
described in the previous sections.
In addition, the CS signal can be used to trigger a new
conversion cycle before the entire serial data transfer has
been completed. The LTC2420 will abort any serial data
transfer in progress and start a new conversion cycle anytime a LOW-to-HIGH transition is detected at the CS pin
after the converter has entered the data output state (i.e.,
after the first rising edge of SCK occurs while CS is LOW).
Finally, CS can be used to control the free-running modes
of operation, see Serial Interface Timing Modes section.
Grounding CS will force the ADC to continuously convert
at the maximum output rate selected by FO. Tying a
capacitor to CS will reduce the output rate and power
dissipation by a factor proportional to the capacitor’s
value, see Figures 13 to 15.
External Serial Clock, Single Cycle Operation
(SPI/MICROWIRE Compatible)
This timing mode uses an external serial clock to shift out
the conversion result and a CS signal to monitor and
control the state of the conversion cycle, see Figure 6.
The serial clock mode is selected on the falling edge of CS.
To select the external serial clock mode, the serial clock pin
(SCK) must be LOW during each CS falling edge.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
While CS is pulled LOW, EOC is output to the SDO pin. EOC
= 1 while a conversion is in progress and EOC = 0 if the
device is in the sleep state. Independent of CS, the device
automatically enters the low power sleep state once the
conversion is complete.
When the device is in the sleep state (EOC = 0), its
conversion result is held in an internal static shift register. The device remains in the sleep state until the first
rising edge of SCK is seen while CS is LOW. Data is shifted
out the SDO pin on each falling edge of SCK. This enables
Table 4. LTC2420 Interface Timing Modes
Configuration
SCK
Source
Conversion
Cycle
Control
Data
Output
Control
Connection
and
Waveforms
External SCK, Single Cycle Conversion
External
CS and SCK
CS and SCK
Figures 6, 7
External SCK, 2-Wire I/O
External
SCK
SCK
Figure 8
Internal SCK, Single Cycle Conversion
Internal
CS ↓
CS ↓
Figures 9, 10
Internal SCK, 2-Wire I/O, Continuous Conversion
Internal
Continuous
Internal
Figure 11
Internal SCK, Autostart Conversion
Internal
CEXT
Internal
Figure 12
15
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
2.7V TO 5.5V
VCC
1µF
VCC
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
FO
LTC2420
VREF
0.1V TO VCC
VIN
–0.12VREF TO 1.12VREF
VREF
SCK
VIN
SDO
GND
CS
CS
TEST EOC
TEST EOC
SDO
BIT 23
EOC
Hi-Z
BIT 22
BIT 21
BIT 20
BIT 19
SIG
EXR
MSB
BIT 18
BIT 4
Hi-Z
BIT 0
TEST EOC
LSB20
Hi-Z
SCK
(EXTERNAL)
CONVERSION
SLEEP
DATA OUTPUT
CONVERSION
2420 F06
Figure 6. External Serial Clock, Single Cycle Operation
external circuitry to latch the output on the rising edge of
SCK. EOC can be latched on the first rising edge of SCK
and the last bit of the conversion result can be latched on
the 24th rising edge of SCK. On the 24th falling edge of
SCK, the device begins a new conversion. SDO goes HIGH
(EOC = 1) indicating a conversion is in progress.
External Serial Clock, 2-Wire I/O
At the conclusion of the data cycle, CS may remain LOW
and EOC monitored as an end-of-conversion interrupt.
Alternatively, CS may be driven HIGH setting SDO to Hi-Z.
As described above, CS may be pulled LOW at any time in
order to monitor the conversion status.
The external serial clock mode is selected at the end of the
power-on reset (POR) cycle. The POR cycle is concluded
approximately 0.5ms after VCC exceeds 2.2V. The level
applied to SCK at this time determines if SCK is internal or
external. SCK must be driven LOW prior to the end of POR
in order to enter the external serial clock timing mode.
Typically, CS remains LOW during the data output state.
However, the data output state may be aborted by pulling
CS HIGH anytime between the first rising edge and the
24th falling edge of SCK, see Figure 7. On the rising edge
of CS, the device aborts the data output state and immediately initiates a new conversion. This is useful for systems not requiring all 24 bits of output data, aborting an
invalid conversion cycle or synchronizing the start of a
conversion.
16
This timing mode utilizes a 2-wire serial I/O interface. The
conversion result is shifted out of the device by an externally generated serial clock (SCK) signal, see Figure 8. CS
may be permanently tied to ground (Pin 4), simplifying the
user interface or isolation barrier.
Since CS is tied LOW, the end-of-conversion (EOC) can be
continuously monitored at the SDO pin during the convert
and sleep states. EOC may be used as an interrupt to an
external controller indicating the conversion result is
ready. EOC = 1 while the conversion is in progress and EOC
= 0 once the conversion enters the low power sleep state.
On the falling edge of EOC, the conversion result is loaded
LTC2420
U
U
W
U
APPLICATIO S I FOR ATIO
2.7V TO 5.5V
VCC
1µF
VCC
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
FO
LTC2420
VREF
0.1V TO VCC
VIN
–0.12VREF TO 1.12VREF
VREF
SCK
VIN
SDO
GND
CS
BIT 22
BIT 21
BIT 20
BIT 19
SIG
EXR
MSB
CS
TEST EOC
BIT 0
SDO
TEST EOC
BIT 23
EOC
EOC
Hi-Z
Hi-Z
BIT 9
TEST EOC
BIT 8
Hi-Z
Hi-Z
SCK
(EXTERNAL)
SLEEP
CONVERSION
SLEEP
DATA OUTPUT
CONVERSION
2420 F07
DATA OUTPUT
Figure 7. External Serial Clock, Reduced Data Output Length
2.7V TO 5.5V
VCC
1µF
VCC
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
FO
LTC2420
VREF
0.1V TO VCC
VIN
–0.12VREF TO 1.12VREF
VREF
SCK
VIN
SDO
GND
CS
CS
BIT 23
SDO
EOC
BIT 22
BIT 21
BIT 20
BIT 19
SIG
EXR
MSB
BIT 18
BIT 4
BIT 0
LSB20
SCK
(EXTERNAL)
CONVERSION
SLEEP
DATA OUTPUT
CONVERSION
2420 F07
Figure 8. External Serial Clock, CS = 0 Operation
17
LTC2420
U
U
W
U
APPLICATIO S I FOR ATIO
to the SDO pin. EOC = 1 while a conversion is in progress
and EOC = 0 if the device is in the sleep state.
into an internal static shift register. The device remains in
the sleep state until the first rising edge of SCK. Data is
shifted out the SDO pin on each falling edge of SCK
enabling external circuitry to latch data on the rising edge
of SCK. EOC can be latched on the first rising edge of SCK.
On the 24th falling edge of SCK, SDO goes HIGH (EOC = 1)
indicating a new conversion has begun.
When testing EOC, if the conversion is complete (EOC = 0),
the device will exit the sleep state and enter the data output
state if CS remains LOW. In order to prevent the device
from exiting the low power sleep state, CS must be pulled
HIGH before the first rising edge of SCK. In the internal
SCK timing mode, SCK goes HIGH and the device begins
outputting data at time tEOCtest after the falling edge of CS
(if EOC = 0) or tEOCtest after EOC goes LOW (if CS is LOW
during the falling edge of EOC). The value of tEOCtest is 23µs
if the device is using its internal oscillator (F0 = logic LOW
or HIGH). If FO is driven by an external oscillator of
frequency fEOSC, then tEOCtest is 3.6/fEOSC. If CS is pulled
HIGH before time tEOCtest, the device remains in the sleep
state. The conversion result is held in the internal static
shift register.
Internal Serial Clock, Single Cycle Operation
This timing mode uses an internal serial clock to shift out
the conversion result and a CS signal to monitor and
control the state of the conversion cycle, see Figure 9.
In order to select the internal serial clock timing mode, the
serial clock pin (SCK) must be floating (Hi-Z) or pulled
HIGH prior to the falling edge of CS. The device will not
enter the internal serial clock mode if SCK is driven LOW
on the falling edge of CS. An internal weak pull-up resistor
is active on the SCK pin during the falling edge of CS;
therefore, the internal serial clock timing mode is automatically selected if SCK is not externally driven.
If CS remains LOW longer than tEOCtest, the first rising
edge of SCK will occur and the conversion result is serially
shifted out of the SDO pin. The data output cycle begins on
this first rising edge of SCK and concludes after the 24th
rising edge. Data is shifted out the SDO pin on each falling
edge of SCK. The internally generated serial clock is output
to the SCK pin. This signal may be used to shift the
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
Once CS is pulled LOW, SCK goes LOW and EOC is output
2.7V TO 5.5V
VCC
VCC
1µF
VCC
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
FO
10k
LTC2420
VREF
0.1V TO VCC
VIN
–0.12VREF TO 1.12VREF
VREF
SCK
VIN
SDO
GND
CS
<tEOCtest
CS
TEST EOC
SDO
BIT 23
EOC
Hi-Z
BIT 22
BIT 21
BIT 20
BIT 19
SIG
EXR
MSB
BIT 18
BIT 4
BIT 0
TEST EOC
LSB20
Hi-Z
Hi-Z
Hi-Z
SCK
(INTERNAL)
CONVERSION
SLEEP
DATA OUTPUT
CONVERSION
2420 F09
Figure 9. Internal Serial Clock, Single Cycle Operation
18
LTC2420
U
U
W
U
APPLICATIO S I FOR ATIO
conversion result into external circuitry. EOC can be
latched on the first rising edge of SCK and the last bit of the
conversion result on the 24th rising edge of SCK. After the
24th rising edge, SDO goes HIGH (EOC = 1), SCK stays
HIGH, and a new conversion starts.
Typically, CS remains LOW during the data output state.
However, the data output state may be aborted by pulling
CS HIGH anytime between the first and 24th rising edge of
SCK, see Figure 10. On the rising edge of CS, the device
aborts the data output state and immediately initiates a
new conversion. This is useful for systems not requiring
all 24 bits of output data, aborting an invalid conversion
cycle, or synchronizing the start of a conversion. If CS is
pulled HIGH while the converter is driving SCK LOW, the
internal pull-up is not available to restore SCK to a logic
HIGH state. This will cause the device to exit the internal
serial clock mode on the next falling edge of CS. This can
be avoided by adding an external 10k pull-up resistor to
the SCK pin or by never pulling CS HIGH when SCK is LOW.
Whenever SCK is LOW, the LTC2420’s internal pull-up at
pin SCK is disabled. Normally, SCK is not externally driven
if the device is in the internal SCK timing mode. However,
certain applications may require an external driver on SCK.
If this driver goes Hi-Z after outputting a LOW signal, the
LTC2420’s internal pull-up remains disabled. Hence, SCK
remains LOW. On the next falling edge of CS, the device is
switched to the external SCK timing mode. By adding an
external 10k pull-up resistor to SCK, this pin goes HIGH
once the external driver goes Hi-Z. On the next CS falling
edge, the device will remain in the internal SCK timing
mode.
A similar situation may occur during the sleep state when
CS is pulsed HIGH-LOW-HIGH in order to test the conversion status. If the device is in the sleep state (EOC = 0), SCK
will go LOW. Once CS goes HIGH (within the time period
defined above as tEOCtest), the internal pull-up is activated.
For a heavy capacitive load on the SCK pin, the internal
pull-up may not be adequate to return SCK to a HIGH level
before CS goes low again. This is not a concern under
normal conditions where CS remains LOW after detecting
EOC = 0. This situation is easily overcome by adding an
external 10k pull-up resistor to the SCK pin.
2.7V TO 5.5V
VCC
VCC
1µF
VCC
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
FO
10k
LTC2420
VREF
0.1V TO VCC
VIN
–0.12VREF TO 1.12VREF
VREF
SCK
VIN
SDO
GND
> tEOCtest
CS
<tEOCtest
CS
TEST EOC
BIT 0
SDO
TEST EOC
EOC
Hi-Z
BIT 23
EOC
Hi-Z
Hi-Z
BIT 22
BIT 21
BIT 20
BIT 19
SIG
EXR
MSB
BIT 18
Hi-Z
BIT 8
TEST EOC
Hi-Z
SCK
(INTERNAL)
SLEEP
CONVERSION
SLEEP
DATA OUTPUT
DATA OUTPUT
CONVERSION
2420 F10
Figure 10. Internal Serial Clock, Reduced Data Output Length
19
LTC2420
U
U
W
U
APPLICATIO S I FOR ATIO
Internal Serial Clock, 2-Wire I/O,
Continuous Conversion
then immediately begins outputting data. The data output
cycle begins on the first rising edge of SCK and ends after
the 24th rising edge. Data is shifted out the SDO pin on
each falling edge of SCK. The internally generated serial
clock is output to the SCK pin. This signal may be used
to shift the conversion result into external circuitry. EOC
can be latched on the first rising edge of SCK and the last
bit of the conversion result can be latched on the 24th
rising edge of SCK. After the 24th rising edge, SDO goes
HIGH (EOC = 1) indicating a new conversion is in progress.
SCK remains HIGH during the conversion.
This timing mode uses a 2-wire, all output (SCK and SDO)
interface. The conversion result is shifted out of the device
by an internally generated serial clock (SCK) signal, see
Figure 11. CS may be permanently tied to ground (Pin 4),
simplifying the user interface or isolation barrier.
The internal serial clock mode is selected at the end of the
power-on reset (POR) cycle. The POR cycle is concluded
approximately 0.5ms after VCC exceeds 2.2V. An internal
weak pull-up is active during the POR cycle; therefore, the
internal serial clock timing mode is automatically selected
if SCK is not externally driven LOW (if SCK is loaded such
that the internal pull-up cannot pull the pin HIGH, the
external SCK mode will be selected).
Internal Serial Clock, Autostart Conversion
This timing mode is identical to the internal serial clock,
2-wire I/O described above with one additional feature.
Instead of grounding CS, an external timing capacitor is
tied to CS.
During the conversion, the SCK and the serial data output
pin (SDO) are HIGH (EOC = 1). Once the conversion is
complete, SCK and SDO go LOW (EOC = 0) indicating the
conversion has finished and the device has entered the
low power sleep state. The part remains in the sleep state
a minimum amount of time (1/2 the internal SCK period)
While the conversion is in progress, the CS pin is held
HIGH by an internal weak pull-up. Once the conversion is
complete, the device enters the low power sleep state and
an internal 25nA current source begins discharging the
2.7V TO 5.5V
VCC
1µF
VCC
FO
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
LTC2420
VREF
0.1V TO VCC
VIN
–0.12VREF TO 1.12VREF
VREF
SCK
VIN
SDO
GND
CS
CS
BIT 23
SDO
BIT 22
EOC
BIT 21
BIT 20
BIT 19
SIG
EXR
MSB
BIT 18
BIT 4
BIT 0
LSB20
SCK
(INTERNAL)
CONVERSION
DATA OUTPUT
SLEEP
Figure 11. Internal Serial Clock, Continuous Operation
20
CONVERSION
2420 F11
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
capacitor tied to CS, see Figure 12. The time the converter
spends in the sleep state is determined by the value of the
external timing capacitor, see Figures 13 and 14. Once the
voltage at CS falls below an internal threshold (≈1.4V), the
device automatically begins outputting data. The data
output cycle begins on the first rising edge of SCK and
ends on the 24th rising edge. Data is shifted out the SDO
pin on each falling edge of SCK. The internally generated
serial clock is output to the SCK pin. This signal may be
used to shift the conversion result into external circuitry.
After the 24th rising edge, CS is pulled HIGH and a new
conversion is immediately started. This is useful in applications requiring periodic monitoring and ultralow power.
Figure 15 shows the average supply current as a function
of capacitance on CS.
without disturbing the converter operation using a regular
oscilloscope probe. When using this configuration, it is
important to minimize the external leakage current at the
CS pin by using a low leakage external capacitor and
properly cleaning the PCB surface.
7
6
tSAMPLE (SEC)
5
4
3
2
VCC = 5V
1
It should be noticed that the external capacitor discharge
current is kept very small in order to decrease the converter power dissipation in the sleep state. In the autostart
mode the analog voltage on the CS pin cannot be observed
VCC = 3V
0
10
100
1000
10000
CAPACITANCE ON CS (pF)
1
100000
2420 F13
Figure 13. CS Capacitance vs fSAMPLE
2.7V TO 5.5V
VCC
1µF
VCC
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
FO
LTC2420
VREF
0.1V TO VCC
VIN
–0.12VREF TO 1.12VREF
VREF
SCK
VIN
SDO
GND
CS
CEXT
VCC
CS
GND
BIT 23
SDO
EOC
BIT 22
BIT 21
BIT 0
SIG
Hi-Z
Hi-Z
SCK
(INTERNAL)
CONVERSION
SLEEP
DATA OUTPUT
CONVERSION
2420 F12
Figure 12. Internal Serial Clock, Autostart Operation
21
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
The digital output signals (SDO and SCK in Internal SCK
mode of operation) are less of a concern because they are
not generally active during the conversion state.
8
7
SAMPLE RATE (Hz)
6
VCC = 5V
5
VCC = 3V
4
3
2
1
0
0
10
100
10000 100000
1000
CAPACITANCE ON CS (pF)
2420 F14
Figure 14. CS Capacitance vs Output Rate
300
SUPPLY CURRENT (µARMS)
250
In an alternative configuration, the GND pin of the converter
can be the single-point-ground in a single point grounding
system. The input signal ground, the reference signal
ground, the digital drivers ground (usually the digital
ground) and the power supply ground (the analog ground)
should be connected in a star configuration with the common point located as close to the GND pin as possible.
VCC = 5V
200
VCC = 3V
150
100
50
0
1
10
100
1000
10000
CAPACITANCE ON CS (pF)
100000
2420 F15
Figure 15. CS Capacitance vs Supply Current
The internal serial clock mode is selected every time the
voltage on the CS pin crosses an internal threshold voltage. An internal weak pull-up at the SCK pin is active while
CS is discharging; therefore, the internal serial clock
timing mode is automatically selected if SCK is floating. It
is important to ensure there are no external drivers pulling
SCK LOW while CS is discharging.
DIGITAL SIGNAL LEVELS
The LTC2420’s digital interface is easy to use. Its digital
inputs (FO, CS and SCK in External SCK mode of operation)
accept standard TTL/CMOS logic levels and the internal
hysteresis receivers can tolerate edge rates as slow as
100µs. However, some considerations are required to take
advantage of exceptional accuracy and low supply current.
22
In order to preserve the LTC2420’s accuracy, it is very
important to minimize the ground path impedance which
may appear in series with the input and/or reference signal
and to reduce the current which may flow through this path.
The GND pin should be connected to a low resistance
ground plane through a minimum length trace. The use of
multiple via holes is recommended to further reduce the
connection resistance. The LTC2420’s power supply current flowing through the 0.01Ω resistance of the common
ground pin will develop a 2.5µV offset signal. For a reference voltage VREF = 2.5V, this represents a 1ppm offset
error.
The power supply current during the conversion state
should be kept to a minimum. This is achieved by restricting the number of digital signal transitions occurring
during this period.
While a digital input signal is in the range 0.5V to
(VCC␣ –␣ 0.5V), the CMOS input receiver draws additional
current from the power supply. It should be noted that,
when any one of the digital input signals (FO, CS and SCK
in External SCK mode of operation) is within this range, the
LTC2420 power supply current may increase even if the
signal in question is at a valid logic level. For micropower
operation and in order to minimize the potential errors due
to additional ground pin current, it is recommended to
drive all digital input signals to full CMOS levels
[VIL < 0.4V and VOH > (VCC – 0.4V)].
Severe ground pin current disturbances can also occur
due to the undershoot of fast digital input signals. Undershoot and overshoot can occur because of the impedance mismatch at the converter pin when the transition
time of an external control signal is less than twice the
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
propagation delay from the driver to LTC2420. For reference, on a regular FR-4 board, signal propagation velocity is approximately 183ps/inch for internal traces and
170ps/inch for surface traces. Thus, a driver generating
a control signal with a minimum transition time of 1ns
must be connected to the converter pin through a trace
shorter than 2.5 inches. This problem becomes particularly difficult when shared control lines are used and
multiple reflections may occur. The solution is to carefully terminate all transmission lines close to their characteristic impedance.
Parallel termination near the LTC2420 pin will eliminate
this problem but will increase the driver power dissipation.
A series resistor between 27Ω and 56Ω placed near the
driver or near the LTC2420 pin will also eliminate this
problem without additional power dissipation. The actual
resistor value depends upon the trace impedance and
connection topology.
Driving the Input and Reference
The analog input and reference of the typical delta-sigma
analog-to-digital converter are applied to a switched capacitor network. This network consists of capacitors switching between the analog input (VIN), ground (Pin 4) and the
reference (VREF). The result is small current spikes seen at
both VIN and VREF. A simplified input equivalent circuit is
shown in Figure 16.
The key to understanding the effects of this dynamic input
current is based on a simple first order RC time constant
model. Using the internal oscillator, the LTC2420’s internal switched capacitor network is clocked at 153,600Hz
corresponding to a 6.5µs sampling period. Fourteen time
constants are required each time a capacitor is switched in
order to achieve 1ppm settling accuracy.
Therefore, the equivalent time constant at VIN and VREF
should be less than 6.5µs/14 = 460ns in order to achieve
1ppm accuracy.
Input Current (VIN)
If complete settling occurs on the input, conversion results will be uneffected by the dynamic input current. If the
settling is incomplete, it does not degrade the linearity
performance of the device. It simply results in an offset/
full-scale shift, see Figure 17. To simplify the analysis of
input dynamic current, two separate cases are assumed:
large capacitance at VIN (CIN > 0.01µF) and small capacitance at VIN (CIN < 0.01µF).
If the total capacitance at VIN (see Figure 18) is small
(< 0.01µF), relatively large external source resistances (up
to 80k for 20pF parasitic capacitance) can be tolerated
without any offset/full-scale error. Figures 19 and 20 show
a family of offset and full-scale error curves for various
small valued input capacitors (CIN < 0.01µF) as a function
of input source resistance.
TUE
VCC
IREF(LEAK)
RSW
5k
VREF
0
IREF(LEAK)
VCC
IIN
IIN(LEAK) RSW
5k
AVERAGE INPUT CURRENT:
IIN = 0.25(VIN – 0.5 • VREF)fCEQ
VIN
RSW
5k
GND
VREF
VIN
2420 F17
Figure 17. Offset/Full-Scale Shift
CEQ
1pF (TYP)
IIN(LEAK)
VREF/2
RSOURCE
VIN
2420 F16
SWITCHING FREQUENCY
f = 153.6kHz FOR INTERNAL OSCILLATOR (fO = LOGIC LOW OR HIGH)
f = fEOSC FOR EXTERNAL OSCILLATORS
INTPUT
SIGNAL
SOURCE
CIN
CPAR
≅ 20pF
LTC2420
2420 F18
Figure 16. LTC2420 Equivalent Analog Input Circuit
Figure 18. An RC Network at VIN
23
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
50
30
CIN = 0pF
CIN = 100pF
CIN = 1000pF
20
CIN = 22µF
CIN = 10µF
CIN = 1µF
CIN = 0.1µF
CIN = 0.01µF
CIN = 0.001µF
30
OFFSET ERROR (ppm)
40
OFFSET ERROR (ppm)
35
VCC = 5V
VREF = 5V
VIN = 0V
TA = 25°C
CIN = 0.01µF
25
20 VCC = 5V
VREF = 5V
15 VIN = 0V
TA = 25°C
10
10
5
0
0
1
10
1k
100
RSOURCE (Ω)
10k
100k
0
200
400
600
RSOURCE (Ω)
800
2420 F19
2420 F21
Figure 19. Offset vs RSOURCE (Small C)
Figure 21. Offset vs RSOURCE (Large C)
10
5
0
FULL-SCALE ERROR (ppm)
FULL-SCALE ERROR (ppm)
0
–10
CIN = 0pF
CIN = 100pF
CIN = 1000pF
–20
–30
VCC = 5V
VREF = 5V
VIN = 5V
TA = 25°C
–40
–50
1
10
CIN = 0.01µF
VCC = 5V
VREF = 5V
VIN = 0V
TA = 25°C
–5
–10
–15
–20
CIN = 22µF
CIN = 10µF
CIN = 1µF
CIN = 0.1µF
CIN = 0.01µF
CIN = 0.001µF
–25
–30
–35
100
1k
RSOURCE (Ω)
10k
100k
0
200
400
600
RSOURCE (Ω)
Figure 20. Full-Scale Error vs RSOURCE (Small C)
For large input capacitor values (CIN > 0.01µF), the input
spikes are averaged by the capacitor into a DC current. The
gain shift becomes a linear function of input source
resistance independent of input capacitance, see Figures
21 and 22. The equivalent input impedance is 16.6MΩ.
This results in ±150nA of input dynamic current at the
extreme values of VIN (VIN = 0V and VIN = VREF, when
VREF = 5V). This corresponds to a 0.3ppm shift in offset
and full-scale readings for every 10Ω of input source
resistance.
In addition to the input current spikes, the input ESD
protection diodes have a temperature dependent leakage
current. This leakage current, nominally 1nA (±10nA
max), results in a fixed offset shift of 10µV for a 10k source
resistance.
800
1000
2420 F22
2420 F20
24
1000
Figure 22. Full-Scale Error vs RSOURCE (Large C)
Reference Current (VREF)
Similar to the analog input, the reference input has a
dynamic input current. This current has negligible effect
on the offset. However, the reference current at VIN = VREF
is similar to the input current at full-scale. For large values
of reference capacitance (CVREF > 0.01µF), the full-scale
error shift is 0.03ppm/Ω of external reference resistance
independent of the capacitance at VREF, see Figure 23. If
the capacitance tied to VREF is small (CVREF < 0.01µF), an
input resistance of up to 80k (20pF parasitic capacitance
at VREF) may be tolerated, see Figure 24.
Unlike the analog input, the integral nonlinearity of the
device can be degraded with excessive external RC time
constants tied to the reference input. If the capacitance at
LTC2420
U
U
W
U
APPLICATIO S I FOR ATIO
60
VCC = 5V
V
= 5V
40 T REF
A = 25°C
40
INL ERROR (ppm)
50
FULL-SCALE ERROR (ppm)
50
CVREF = 22µF
CVREF = 10µF
CVREF = 1µF
CVREF = 0.1µF
CVREF = 0.01µF
CVREF = 0.001µF
30 VCC = 5V
VREF = 5V
20 VIN = 5V
TA = 25°C
30
CVREF = 1000pF
20
CVREF = 100pF
10
CVREF = 0.01µF
10
0
0
–10
CVREF = 0pF
–20
–10
0
200
400
600
800
RESISTANCE AT VREF (Ω)
1
1000
10
100
1k
10k
RESISTANCE AT VREF (Ω)
2420 F25
2420 F23
Figure 23. Full-Scale Error vs RVREF (Large C)
Figure 25. INL Error vs RVREF (Small C)
10
500
6
CVREF = 1000pF
CVREF = 100pF
200
CVREF = 0.01µF
100
0
CVREF = 22µF
CVREF = 10µF
CVREF = 1µF
CVREF = 0.1µF
CVREF = 0.01µF
CVREF = 0.001µF
8
INL ERROR (ppm)
VOLTAGE
VCC = 5V
= 5V
V
400 VREF= 5V
IN
TA = 25°C
300
CVREF = 0pF
–100
100k
4
2
VCC = 5V
VREF = 5V
TA = 25°C
0
–2
–4
–6
–8
–10
–200
1
10
100
1k
10k
RESISTANCE AT VREF (Ω)
100k
0
node VREF is small (CVREF < 0.01µF), the reference input
can tolerate large external resistances without reduction
in INL, see Figure 25. If the external capacitance is large
(CVREF > 0.01µF), the linearity will be degraded by
0.015ppm/Ω independent of capacitance at VREF, see
Figure 26.
In addition to the dynamic reference current, the VREF ESD
protection diodes have a temperature dependent leakage
current. This leakage current, nominally 1nA (±10nA max),
results in a fixed full-scale shift of 10µV for a 10k source
resistance.
400
600
800
RESISTANCE AT VREF (Ω)
1000
2420 F26
2420 F24
Figure 24. Full-Scale Error vs RVREF (Small C)
200
Figure 26. INL Error vs RVREF (Large C)
ANTIALIASING
One of the advantages delta-sigma ADCs offer over conventional ADCs is on-chip digital filtering. Combined with
a large oversampling ratio, the LTC2420 significantly
simplifies antialiasing filter requirements.
The digital filter provides very high rejection except at
integer multiples of the modulator sampling frequency
(fS), see Figure 27. The modulator sampling frequency is
256 • FO, where FO is the notch frequency (typically 50Hz
or 60Hz). The bandwidth of signals not rejected by the
digital filter is narrow (≈ 0.2%) compared to the bandwidth
of the frequencies rejected.
25
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
0
800Hz NOTCH (100 SAMPLES/SECOND)
–20
60Hz NOTCH (7.5 SAMPLES/SECOND)
REJECTION (dB)
–40
1
2
–60
3
–80
4
LTC2420
VCC
FO
VREF
SCK
VIN
SDO
CS
GND
8
7
6
5
EXTERNAL 2.048MHz CLOCK SOURCE
–100
INTERNAL 153.6kHz OSCILLATOR
2420 F28
–120
Figure 28. Selectable 100 Samples/Second Turbo Mode
–140
0
fS/2
fS
INPUT FREQUENCY
256
VREF = 5V
Figure 27. Sinc4 Filter Rejection
As a result of the oversampling ratio (256) and the digital
filter, minimal (if any) antialias filtering is required in front
of the LTC2420. If passive RC components are placed in
front of the LTC2420 the input dynamic current should be
considered (see Input Current section). In cases where
large effective RC time constants are used, an external
buffer amplifier may be required to minimize the effects of
input dynamic current.
TOTAL UNADJUSTED ERROR (ppm)
2420 F27
12 BITS
224
192
160
13 BITS
128
96
14 BITS
64
32
0
16 BITS
0
50
100
150
OUTPUT RATE (SAMPLES/SEC)
2420 F29
The modulator contained within the LTC2420 can handle
large-signal level perturbations without saturating. Signal
levels up to 40% of VREF do not saturate the analog modulator. These signals are limited by the input ESD protection
to 300mV below ground and 300mV above VCC.
Operation at Higher Data Output Rates
The LTC2420 typically operates with an internal oscillator
of 153.6kHz. This corresponds to a notch frequency of
60Hz and an output rate of 7.5 samples/second. The
internal oscillator is enabled if the FO pin is logic LOW
(logic HIGH for a 50Hz notch). It is possible to drive the FO
pin with an external oscillator for higher data output rates.
As shown in Figure 28, an external clock of 2.048MHz
applied to the FO pin results in a notch frequency of 800Hz
with a data output rate of 100 samples/second.
Figure 29 shows the total unadjusted error (Offset Error +
Full-Scale Error + INL + DNL) as a function of the output
data rate with a 5V reference. The relationship between the
26
Figure 29. Total Error vs Output Rate (VREF = 5V)
output data rate (ODR) and the frequency applied to the FO
pin (FO) is:
ODR = FO/20480
For output data rates up to 50 samples/second, the total
unadjusted error (TUE) is better than 16 bits, and better
than 12 bits at 100 samples/second. As shown in Figure
30, for output data rates of 100 samples/second, the TUE
is better than 15 bits for VREF below 2.5V. Figure 31 shows
an unaveraged total unadjusted error for the LTC2420 operating at 100 samples/second with VREF = 2.5V. Figure 32
shows the same device operating with a 5V reference and
an output data rate of 7.5 samples/second.
At 100 samples/second, the LTC2420 can be used to
capture transient data. This is useful for monitoring settling or auto gain ranging in a system. The LTC2420 can
monitor signals at an output rate of 100 samples/second.
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
256
TOTAL UNADJUSTED ERROR (ppm)
OUTPUT RATE = 100sps
12 BITS
224
192
160
13 BITS
128
96
14 BITS
64
15 BITS
32
0
1.0
1.5
2.0 2.5 3.0 3.5 4.0
REFERENCE VOLTAGE (V)
4.5
5.0
2420 F30
Figure 30. Total Error vs VREF (Output Rate = 100sps)
TOTAL UNADJUSTED ERROR (ppm)
VCC = 5V
VREF = 2.5V
5
0
–5
–10
–15
–20
–25
–30
–35
TOTAL UNADJUSTED ERROR (ppm)
6
10
2
0
–2
–4
–6
–8
–10
–40
0
2.5
VCC = 5V
VREF = 5V
4
5
0
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
2420 F31
2420 F32
Figure 31. Total Unadjusted Error at
100 Samples/Second (No Averaging)
Figure 32. Total Unadjusted Error at
7.5 Samples/Second (No Averaging)
After acquiring 100 samples/second data the FO pin may
be driven LOW enabling 60Hz rejection to 110dB and the
highest possible DC accuracy. The no latency architecture
of the LTC2420 allows consecutive readings (one at 100
samples/second the next at 7.5 samples/second) without
interaction between the two readings.
As shown in Figure 33, the LTC2420 can capture transient
data with 90dB of dynamic range (with a 300mVP-P input
signal at 2Hz). The exceptional DC performance of the
LTC2420 enables signals to be digitized independent of a
large DC offset. Figures 34a and 34b show the dynamic
performance with a 15Hz signal superimposed on a 2V DC
level. The same signal with no DC level is shown in Figures
34c and 34d.
27
LTC2420
U
W
U
U
APPLICATIO S I FOR ATIO
0
fIN = 2Hz
500ms
0.15
2Hz
100sps
0V OFFSET
–20
0.10
MAGNITUDE (dB)
ADC OUTPUT (NORMALIZED TO VOLTS)
0.20
0.05
0
–0.05
–40
–60
–80
–0.10
–100
–0.15
–120
–0.20
FREQUENCY (Hz)
TIME
2420 F33b
2420 F33a
33a. Digitized Waveform
33b. Output FFT
Figure 33. Transient Signal Acquisiton
0
VIN = 300mVP-P + 2V DC
2.15
15Hz
100sps
2V OFFSET
–20
2.10
MAGNITUDE (dB)
ADC OUTPUT (NORMALIZED TO VOLTS)
2.20
2.05
2.00
1.95
–40
–60
–80
1.90
–100
1.85
1.80
–120
FREQUENCY (Hz)
TIME
2420 F34b
34a. Digitized Waveform with 2V DC Offset
34b. FFT Waveform with 2V DC Offset
0.20
0
VIN = 300mVP-P + 0V DC
0.15
15Hz
100sps
0V OFFSET
–20
0.10
MAGNITUDE (dB)
ADC OUTPUT (NORMALIZED TO VOLTS)
2420 F34a
0.05
0.00
–0.05
–40
–60
–80
–0.10
–100
–0.15
–0.20
–120
FREQUENCY (Hz)
TIME
2420 F34d
2420 F34c
34c. Digitized Waveform with No Offset
34d. FFT Waveform with No Offset
Figure 34. Using the LTC2420’s High Accuracy Wide Dynamic Range to Digitize
a 300mVP-P 15Hz Waveform with a Large DC Offset (VCC = 5V, VREF = 5V)
28
LTC2420
U
TYPICAL APPLICATIO S
SYNCHRONIZATION OF MULTIPLE LTC2420s
Increasing the Output Rate Using Multiple LTC2420s
Since the LTC2420’s absolute accuracy (total unadjusted
error) is 10ppm, applications utilizing multiple matched
ADCs are possible.
A second application uses multiple LTC2420s to increase
the effective output rate by 4×, see Figure 36. In this case,
four LTC2420s are interleaved under the control of separate CS signals. This increases the effective output rate
from 7.5Hz to 30Hz (up to a maximum of 400Hz). Additionally, the one-shot output spectrum is unfolded allowing further digital signal processing of the conversion
results. SCK and SDO may be common to all four LTC2420s.
The four CS rising edges equally divide one LTC2420
conversion cycle (7.5Hz for 60Hz notch frequency). In
order to synchronize the start of conversion to CS, 23 or
less SCK clock pulses must be applied to each ADC.
Simultaneous Sampling with Two LTC2420s
One such application is synchronizing multiple LTC2420s,
see Figure 35. The start of conversion is synchronized to
the rising edge of CS. In order to synchronize multiple
LTC2420s, CS is a common input to all the ADCs.
To prevent the converters from autostarting a new conversion at the end of data output read, 23 or fewer SCK
clock signals are applied to the LTC2420 instead of 24 (the
24th falling edge would start a conversion). The exact
timing and frequency for the SCK signal is not critical
since it is only shifting out the data. In this case, two
LTC2420’s simultaneously start and end their conversion
cycles under the external control of CS.
Both the synchronous and 4× output rate applications use
the external serial clock and single cycle operation with
reduced data output length (see Serial Interface Timing
Modes section and Figure 7). An external oscillator clock
is applied commonly to the FO pin of each LTC2420 in
order to synchronize the sampling times. Both circuits
may be extended to include more LTC2420s.
SCK2
SCK1
LTC2420
#1
VCC
µCONTROLLER
EXTERNAL OSCILLATOR
(153,600HZ)
LTC2420
#2
FO
FO
VCC
VREF
SCK
VREF
SCK
VIN
SDO
VIN
SDO
GND
CS
GND
CS
CS
SDO1
SDO2
VREF
(0.1V TO VCC)
CS
SCK1
23 OR LESS CLOCK CYCLES
SCK2
23 OR LESS CLOCK CYCLES
SDO1
SDO2
2420 F35
Figure 35. Synchronous Conversion—Extendable
29
LTC2420
U
TYPICAL APPLICATIO S
LTC2420
#1
VCC
µCONTROLLER
LTC2420
#2
FO
VCC
LTC2420
#3
FO
VCC
VREF
(0.1V TO VCC)
EXTERNAL OSCILLATOR
(153,600HZ)
LTC2420
#4
FO
VCC
FO
VREF
SCK
VREF
SCK
VREF
SCK
VREF
SCK
VIN
SDO
VIN
SDO
VIN
SDO
VIN
SDO
GND
CS
GND
CS
GND
CS
GND
CS
SCK
SDO
CS1
CS2
CS3
CS4
CS1
CS2
CS3
CS4
SCK
23 OR LESS
CLOCK PULSES
SDO
2420 F36
Figure 36. 4× Output Rate LTC2420 System
30
LTC2420
U
TYPICAL APPLICATIO S
Single-Chip Instrumentation Amplifier
for the LTC2420
reduces the magnitude of averaged noise by 30% and
improves resolution by 0.5 bit without compromising
linearity. Resistor R2 performs two functions: it isolates
C1 from the LTC2420’s input and limits the LTC2420’s
input current should its input voltage drop below –300mV
or swing above VCC + 300mV.
The circuit in Figure 37 is a simple solution for processing
differential signals in pressure transducer, weigh scale or
strain gauge applications that can operate on a supply
voltage range of ±5V to ±15V. The circuit uses an LT®1920
single-chip instrumentation amplifier to perform a differential to single-ended conversion. The amplifier’s output
voltage is applied to the LTC2420’s input and converted to
a digital value with an overall accuracy exceeding 17 bits
(0.0008%). Key circuit performance results are shown in
Table 5.
The LT1920 is the choice for applications where low cost
is important. For applications where more precision is
required, the LT1167 is a pin-to-pin alternative choice with
a lower offset voltage, lower input bias current and higher
gain accuracy than the LT1920. The LT1920’s maximum
total input-referred offset (VOST) is 135µV for a gain of
100. At the same gain, the LT1167’s VOST is 63µV. At gains
of 10 or 100, the LT1920’s maximum gain error is 0.3%
and its maximum gain nonlinearity is 30ppm. At the same
gains, the LT1167’s maximum gain error is 0.1% and its
maximum gain nonlinearity is 15ppm. Table 6 summarizes the performance of Figure 37’s circuit using the
LT1167.
The practical gain range for this topology as shown is from
5 to 100 because the LTC2420’s wide dynamic range
makes gains below 5 virtually unnecessary, whereas gains
up to 100 significantly reduce the input referred noise.
The optional passive RC lowpass filter between the
amplifier’s output and the LTC2420’s input attenuates
high frequency noise and its effects. Typically, the filter
5V 0.1µF
VREFIN
VS+ 0.1µF
2
DIFFERENTIAL
INPUT
RG**
1
8
3
VIN+
RG
LT1920
RG
VIN–
1
7
R1*
47Ω
6
R2*
10k
0.1µF
C1*
1µF
4
VS –
2
3
VCC
VREF
LTC2420
VIN
SDO
SCK
GND
4
†
†
CS
FO
5
6
7
CHIP SELECT
SERIAL DATA OUT
SERIAL CLOCK
2420 F37
8
†
SINGLE POINT
“STAR” GROUND
*OPTIONAL—SEE TEXT
**RG = 49.4k/(AV – 1): USE 5.49k FOR AV = 10; 499Ω FOR AV = 100
†USE SHORT LEAD LENGTHS
Figure 37. The LT1920 is a Simple Solution That Converts a Differential Input
to a Ground Referred Single-Ended Signal for the LTC2420
31
LTC2420
U
TYPICAL APPLICATIO S
Table 5. Typical Performance of the LTC2420 ADC When Used with the
LT1920 Instrumentation Amplifiers in Figure 34’s Differential Digitizing Circuit
VS = ±5V
PARAMETER
Differential Input Voltage Range
Zero Error
VS = ±15V
AV = 10
AV = 100
AV = 10
AV = 100
TOTAL (UNITS)
– 30 to 400
– 3 to 40
– 30 to 500
– 3 to 50
mV
–160
– 2650
– 213
– 2625
Maximum Input Current
2.0
Nonlinearity
±8.2
±7.4
Noise (Without Averaging)
1.8*
0.25*
Noise (Averaged 64 Readings)
0.2*
0.03*
21
20.6
17.2
17.3
Resolution (with Averaged Readings)
Overall Accuracy (Uncalibrated)
Common Mode Range
±6.5
±6.1
ppm
1.5*
0.27*
µVRMS
0.19*
0.03*
µVRMS
21.3
20.5
Bits
17.5
18.2
Bits
≥120
Common Mode Rejection Ratio
2/–1.5**
2.2/–1.7**
µV
nA
dB
11.5/–11**
11.7/–11.2**
V
*Input referred noise for the respective gain. **Typical values based on single lab tested sample of each amplifier.
Table 6. Typical Performance of the LTC2420 ADC When Used with the
LT1167 Instrumentation Amplifiers in Figure 34’s Differential Digitizing Circuit
VS = ±5V
PARAMETER
Differential Input Voltage Range
Zero Error
VS = ±15V
AV = 10
AV = 100
AV = 10
AV = 100
TOTAL (UNITS)
– 30 to 400
– 3 to 40
– 30 to 500
– 3 to 50
mV
–94
– 1590
– 110
– 1470
Maximum Input Current
0.5
±4.1
±4.4
Noise (Without Averaging)
1.4*
0.19*
Noise (Averaged 64 Readings)
0.18*
0.02*
Resolution (with Averaged Readings)
21.4
21.0
Overall Accuracy (Uncalibrated)
18.2
18.1
Nonlinearity
Common Mode Range
±4.1
±3.7
ppm
1.5*
0.18*
µVRMS
0.19*
0.02*
µVRMS
21.3
21.1
Bits
18.2
19.4
Bits
≥120
Common Mode Rejection Ratio
2/–1.5**
2.2/–1.7**
dB
11.5/–11**
11.7/–11.2**
*Input referred noise for the respective gain. **Typical values based on single lab tested sample of each amplifier.
32
µV
nA
V
LTC2420
U
TYPICAL APPLICATIO S
Using a Low Power Precision Reference
where the noise of the amplifier begins to dominate, the
input referred noise is essentially that of the instrumentation amplifier. The linearity of the instrumentation amplifier does, however, degrade at higher gains. As a result, if
the full linearity of the LTC2420 is desired, gain in the
instrumentation amplifier should be limited to less than
100, possibly requiring averaging multiple samples to
extend the resolution below the noise floor. The noise level
of the LT1167 at gains greater than 100 is on the order of
50nVRMS, although, 1/f noise and temperature effects may
degrade this below 0.1Hz. The introduction of a filter
between the amplifier and the LTC2420 may improve
noise levels under some circumstances by reducing noise
bandwidth. Note that temperature offset drift effects envelope detection in the input of the LT1167 if exposed to RFI,
thermocouple voltages in connectors, resistors and soldered junctions can all compromise results, appearing as
drift or noise. Turbulent airflow over this circuitry should
be avoided.
The circuit in Figure 38 shows the connections and bypassing for an LT1461-2.5 as a 2.5V reference. The
LT1461 is a bandgap reference capable of 3ppm/°C temperature stability yet consumes only 45µA of current. The
1k resistor between the reference and the ADC reduces the
transient load changes associated with sampling and
produces optimal results. This reference will not impact
the noise level of the LTC2420 if signals are less than 60%
full scale, and only marginally increases noise approaching full scale. Even lower power references can be used if
only the lower end of the LTC2420 input range is required.
A Differential to Single-Ended Analog Front End
Figure 39 shows the LT1167 as a means of sensing
differential signals. The noise performance of the LT1167
is such that for gains less than 200, the noise floor of the
LTC2420 remains the dominant noise source. At the point
TO
LTC2420
REF
1k
IN
5V
OUT
0.1µF
LT1461-2.5
CER
+
10µF
16V
TANT
GND
2420 F38
Figure 38. Low Power Reference
5V
+
5V
3.5k
×4
RG
10µF
2
1
8
3
1
2
OPTIONAL
+
6
LT1167
5
–
22Ω
5k
1µF
3
LTC2420
4
–5V
AV = 49.4kΩ + 1
RG
RECOMMENDED RG: 500Ω, 0.1%
5ppm/°C
2428 F39
Figure 39. A Differential to Single-Ended Analog Front End
33
LTC2420
U
TYPICAL APPLICATIO S
relaxation oscillators using the 74HC14 or similar devices. The circuit can be tuned over a 3:1 range with only
one resistor and can be gated. The use of transmission
gates could be used to shift the frequency in order to
provide setable conversion rates.
2.048MHz Oscillator for 100sps Output Ratio
The oscillator circuit shown in Figure 40 can be used to
drive the FO pin, boosting the conversion rate of the
LTC2420 for applications that do not require a notch at
50Hz or 60Hz. This oscillator is not sensitive to hysteresis
voltage of a Schmitt trigger device as are simpler
1k
10k
1k
U1-F
47k
12
2N3904
5k
13
HALT
47k
5pF
270pF
U1-A
1
U1-B
2
10pF
100smps, FO = 2.048MHz
30smps, FO = 614.4kHz
U1: 74HC14 OR EQUIVALENT
3
U1-C
4
5
6
U1-E
11
10
U1-D
9
8 TO LTC2420
FO PIN
2420 F40
Figure 40. 2.048MHz Oscillator for 100sps Output Rate
34
LTC2420
W
PACKAGE I FOR ATIO
Dimensions in inches (millimeters) unless otherwise noted.
U
U
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
8
7
6
5
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
1
0.010 – 0.020
× 45°
(0.254 – 0.508)
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0°– 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.014 – 0.019
(0.355 – 0.483)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
2
3
4
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
BSC
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
SO8 1298
35
LTC2420
U
TYPICAL APPLICATIO
The circuit shown in Figure 41 enables pseudodifferential
measurements of several bridge transducers and absolute temperature measurement. The LTC1391 is an
8-to-1 analog multiplexer.
Consecutive readings are performed on each side of the
bridge by selecting the appropriate channel on the
LTC1391. Each output is digitized and the results digitally
subtracted to obtain the pseudodifferential result. Several
bridge transducers may be digitized in this manner.
In order to measure absolute temperature with a thermocouple, cold junction compensation must be performed.
Channel 6 measures the output of the thermocouple while
channel 7 measures the output of the cold junction sensor
(diode, thermistor, etc.). This enables digital cold junction compensation of the thermocouple output. The temperature measurement may then be used to compensate
the temperature effects of the bridge transducers.
THERMOCOUPLE
CH0
VCC
CH1
LTC1391
CH2
CH3 OUT
THERMISTOR
CH4
CH5
CH6
CH7
VREF VCC
FO
LTC2420
VIN
SCK
SDO
GND
CS
2420 F41
GND
Figure 41. Pseudodifferential Multichannel Bridge Digitizer
and Digital Cold Junction Compensation
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1019
Precision Bandgap Voltage Reference, 2.5V, 5V
3ppm/°C Drift, 0.05% Max
LT1025
Micropower Thermocouple Cold Junction Compensator
0.5°C Initial Accuracy, 80µA Supply Current
LTC1043
Dual Precision Instrumentation Switched Capacitor
Building Block
Precise Charge, Balanced Switching, Low Power
LTC1050
Precision Chopper Stabilized Op Amp
No External Components 5µV Offset, 1.6µVP-P Noise
LT1236A-5
Precision Bandgap Voltage Reference, 5V
0.05% Max, 5ppm/°C Drift
LTC1391
8-Channel Multiplexer
Low RON: 45Ω, Low Charge Injection, Serial Interface
LT1460
Micropower Series Voltage Reference
0.075% Max, 10ppm/°C Max Drift, 2.5V, 5V and 10V Versions
LTC2400
24-Bit µPower, No Latency ∆Σ ADC in SO-8
4ppm INL, 10ppm TUE, 200µA, Pin Compatible with LTC2420
LTC2401/LTC2402
1-/2-Channel, 24-Bit No Latency ∆Σ ADCs
24 Bits in MSOP Package
LTC2404/LTC2408
4-/8-Channel, 24-Bit No Latency ∆Σ ADC
4ppm INL, 10ppm TUE, 200µA
LTC2410
24-Bit No Latency ∆Σ ADC with Differential Inputs
800nV Noise, Differential Reference, 2.7V to 5.5V Operation
LTC2411
24-Bit No Latency ∆Σ ADC with Differential Inputs/Reference
1.6µV Noise, Fully Differential, 10-Lead MSOP Package
LTC2413
24-Bit No Latency ∆Σ ADC
Simultaneous 50Hz to 60Hz Rejection 0.16ppm Noise
LTC2424/LTC2428
4-/8-Channel 20-Bit No Latency ∆Σ ADCs
8ppm INL, 1.2ppm Noise, Fast Mode
36
Linear Technology Corporation
2420f LT/LCG 1000 4K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 2000