USB I P Box User Manual

USB I&P Box User Manual
USB Interface &
Programming Box
Evaluation Programmer for SPI & I2C Interface
www.ams.com
Revision 1.2 / 06/10/2014
page 1/9
USB I&P Box
User Manual
Table of Contents
1
General Description ............................................................................................................. 3
2
Hardware .............................................................................................................................. 4
2.1
Kit Content ........................................................................................................................... 4
2.2
Compatible Products ............................................................................................................ 4
2.3
Pin-out .................................................................................................................................. 5
3
First steps with the USB I&P Box ......................................................................................... 5
4
Software ............................................................................................................................... 7
4.1
GUI Overview ....................................................................................................................... 7
4.2
Firmware Update.................................................................................................................. 8
5
Ordering Information ............................................................................................................ 8
Copyright ............................................................................................................................................. 9
Disclaimer ............................................................................................................................................ 9
Revision History
Revision
Date
Owner
Description
1.0
21.01.2014
AZEN
Initial revision
1.1
06.08.2014
RPH
Minor changes
1.2
06.10.2014
AZEN
Updated Compatible Products
www.ams.com
Revision 1.2 / 06/10/2014
page 2/9
USB I&P Box
User Manual
1
General Description
This Manual explains how to use the USB I&P Box.
The USB I&P Box is a Programming-Tool for Magnetic Position Sensors with I2C or SPI Interface.
After connecting a Magnetic Position Sensor to I&P Box you can open the GUI on your computer
and start programming.
For programming a Magnetic Position Sensor the sensor should be mounted on a PCB to get
connected with all the necessary pins of the sensor.
For Position Sensors, ams provides Adapterboards where an easy access from the Sensor to the
USB I&P Box is possible (not in the Tool-Kit included)
Figure 1:
USB I&P Box
www.ams.com
Revision 1.2 / 06/10/2014
page 3/9
USB I&P Box
User Manual
2
Hardware
2.1
Kit Content
Table 1:
USB I&P Box Kit content
Part
Description
USB I&P Box
USB Interface & Programming Box
USB cable
To connect the USB I&P box
10-way cable
To connect the USB I&P Box to a
compatible sensor on an existing
board
Quick Start Guide
First steps introduction
USB flash drive
Contains the USB I&P Box
Software and manuals.
2.2
Picture
Compatible Products
Table 2:
Compatible Products
Product
Description
Adapterboard available
AS5047D
14-bit On-Axis Magnetic Rotary Position Sensor
yes
AS5048A
14-bit Angular Position Sensor with SPI Interface
yes
AS5048B
14-bit Angular Position Sensor with I2C Interface
yes
AS5050A
Low Power 10-Bit Magnetic Position Sensor
yes
AS5055A
Low Power 12-Bit Magnetic Position Sensor
yes
www.ams.com
Revision 1.2 / 06/10/2014
page 4/9
USB I&P Box
User Manual
Product
Description
Adapterboard available
AS5147
14-bit On-Axis Magnetic Rotary Position Sensor
yes
AS5510
Linear Hall Sensor with I²C Output
yes
AS5600
12-bit Programmable Contactless Potentiometer
yes
AS5601
12-bit Programmable Contactless Encoder
yes
2.3
Pin-out
The pin-out of the USB I&P box is shown below in Table 3
Table 3:
USB I&P Box Pin-out and wire description
Pin #
Color
Definition
SPI Mode
1
Brown
5V Supply
Not used
2
Red
3.3V Supply
Positive power supply
3
Orange
SPI-CS(0)
SPI-CS(0)
4
Yellow
I2C-SCL
Not used
5
Green
SPI-CLK
SPI-CLK
6
Blue
I2C-SDA
Not used
7
Purple
SPI-MOSI
SPI-MOSI
8
Grey
SPI-CS(1)
Optional (dual die version)
9
White
SPI-MISO
SPI-MISO
10
Black
GND
GND
Note: The interface voltage of the USB I&P Box is 3,3V. Use the 3,3V mode when connecting to a
position sensor board.
3
First steps with the USB I&P Box
The first steps to get started with the USB I&P Box are described below in Figure 2.
www.ams.com
Revision 1.2 / 06/10/2014
page 5/9
USB I&P Box
User Manual
Figure 2:
First steps with the USB I&P Box
Getting started with your programmer
Install the USB I&P Software on your
computer
Connect your USB I&P Box to your
computer via USB cable
Connect the right wires of the USB I&P
Connector cable to your magnetic position
sensor
For using the right wires
please refer to Table 3
Open the USB I&P Software
Choose the right Device
Ready to start
www.ams.com
Revision 1.2 / 06/10/2014
page 6/9
USB I&P Box
User Manual
4
Software
4.1
GUI Overview
Also included in your USB I&P Tool is a USB stick with the software.
The software is needed for programming the Magnetic Position Sensor on your computer.
When you copied the software from the USB stick to your computer please click on it and follow
the instructions of the Install Wizard through the installing procedure.
The software is compatible for Windows XP and newer versions.
In Figure 3: you can have a look at the starting page after finishing the installing and no device
connected.
Figure 4 shows the GUI while a Programmer Box connected
Figure 3:
Screenshot of the GUI’s starting page while no Programmer is connected
C
A
B
A: Select the Device (only possible when a I&P Box is detected)
B: Check if the Programmer will be detected (or there is no bootloader on the I&P Box)
C: For firmware updates click on Help and Firmware Update, for further Information about
this topic refer to 4.2
www.ams.com
Revision 1.2 / 06/10/2014
page 7/9
USB I&P Box
User Manual
Figure 4:
Screenshot of the GUI’s starting page while Programmer connected
4.2
5
Firmware Update

Connect your I&P Box to your Computer and open the Software

Click on Help and Firmware Update

Search your computer for the new firmware file and click at it

After that the firmware installs by itself and the update is successful
Ordering Information
Table 4:
Ordering Information
Ordering Code
Description
USB I&P Box
USB Interface & Programming box for I2C/SPI
www.ams.com
Revision 1.2 / 06/10/2014
page 8/9
USB I&P Box
User Manual
Copyright
Copyright ams AG, Tobelbader Strasse 30, 8141 Unterpremstätten, Austria-Europe. Trademarks
Registered. All rights reserved. The material herein may not be reproduced, adapted, merged,
translated, stored, or used without the prior written consent of the copyright owner.
Disclaimer
Demo Kits, Evaluation Kits and Reference Designs are provided on an “as is” basis for demonstration
and evaluation purposes only. Any express or implied warranties, including, but not limited to the
implied warranties of merchantability and fitness for a particular purpose are disclaimed. Any claims
and demands and any direct, indirect, incidental, special, exemplary or consequential damages
arising from the inadequacy of the provided Demo Kits, Evaluation Kits and Reference Designs or
incurred losses of any kind (e.g. loss of use, data or profits, or business interruption however caused)
as a consequence of their use are excluded.
Contact Information
Headquarters
ams AG
Tobelbader Strasse 30
8141 Unterpremstaetten
Austria
T. +43 (0) 3136 500 0
For Sales Offices, Distributors and Representatives, please visit:
http://www.ams.com/contact
www.ams.com
Revision 1.2 / 06/10/2014
page 9/9