MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide Doc. # 002-07484 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): +1.408.943.2600 www.cypress.com Copyrights © Cypress Semiconductor Corporation, 2009-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 2 Preface Thank you for purchasing the LQFP-64P (0.65 mm pitch) *1 header board (model number : MB2146-223) for the F2MC-8FX family. MB2146-223 is a header board used to connect the MCU board (model number : MB2146-301A-E, MB2146-303A-E) which mounts the F2MC-8FX family evaluation MCU to a user system. This manual explains the handling of the MB2146-223. Before using MB2146-223, be sure to read this manual. Consult the Sales representatives or the Support representatives of Cypress for mass-produced MCUs and evaluation MCUs which correspond on MB2146-223. MB2146-223 is an object about MCU with a built-in LCD controller. *1: The lead pitch of package (FPT-64P-M23) is 0.65 mm and the body size is 12 mm × 12 mm. ■ European RoHS compliance Products with a -E suffix on the part number are European RoHS compliant products. ■ Notice on this document All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. ■ Caution of the products described in this document The following precautions apply to the product described in this manual. CAUTION The wrong use of a device will give an injury and may cause malfunction on customers system. Cuts This product has parts with sharp points that are exposed. Do not touch an edge of the product with your bare hands. Damage When connecting the header board to the user system, correctly position the index mark (▲) on the NQPACK mounted on the user system with the 1 pin direction(1) on the header board, otherwise the MCU board and user system might be damaged. Damage When mounting a mass production MCU, correctly position pin 1, otherwise the mass production MCU and user system might be damaged. MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 3 Contents 1. Product Outline 1.1 1.2 5 Product Outline ............................................................................................................5 Product Configuration ..................................................................................................6 2. Checking the Delivered Product 7 3. Handling Precautions 8 4. Notes on Designing 9 4.1 4.2 Notes on Designing Printed Circuit Board for the User System ..................................9 MCU Footprint Design Notes.....................................................................................10 5. Connecting to the User System 5.1 5.2 Connecting.................................................................................................................11 Disconnection ............................................................................................................12 6. Mounting Mass Production MCUs 6.1 6.2 13 Mounting ....................................................................................................................13 Disconnection ............................................................................................................14 7. Product Specifications 7.1 7.2 7.3 7.4 11 15 General Specifications...............................................................................................15 Main Part ...................................................................................................................15 Functional Block Diagram ..........................................................................................16 User System I/F YQPACK (U1) .................................................................................19 Revision History MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 20 4 1. 1.1 Product Outline Product Outline MB2146-223 is a header board (referred to as header board) used to connect the MCU board (model number : MB2146-301A-E, MB2146-303A-E) which mounts an evaluation MCU in the F2MC-8FX family of Cypress 8-bit microcontrollers to a user system. To build an F2MC-8FX evaluation environment, combine the three products as shown in Figure 1-1: the header board, a MCU board, and a BGM adapter (model number : MB2146-09A-E). For more information please visit our following websites: www.cypress.com/documentation/development-kitsboards/mb2146-223 www.cypress.com/documentation/development-kitsboards/mb2146-09a-e www.cypress.com/documentation/development-kitsboards/mb2146-301a-e www.cypress.com/documentation/development-kitsboards/mb2146-301a-e Figure 1-1. System Configuration MB2146-09 MCU board BGM adapter Header board MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 5 Product Outline 1.2 Product Configuration Table 1-1 lists the product configuration in the header board, and Table 1-2 lists options. Table 1-1. Product Cofiguration Name F2 Description Remarks MC-8FX LQFP-64P (0.65 mm pitch) Connector/LQFP64pin header board (0.65 mm pitch) Package conversion - [Model number : MB2146-223] [Model number : YQPACK064SB] (Tokyo Eletech Corporation) [Model number : NQPACK064SB] (Tokyo Eletech Corporation) [Model number : HQPACK064SB140] (Tokyo Eletech Corporation) I/F between header board and NQPACK Accessory (connected) For mounted on user system Accessory Used when mounting mass production MCU to NQPACK. Accessory Table 1-2. Options Name BGM adapter [Model number : MB2146-09A-E] MCU board [Model number : MB2146-301A-E, MB2146-303A-E] Description ICE unit for F2MC-8FX Remarks - Built-in MB95FV100D-101, Built-in F2MC-8FX evaluation MCU * MB95FV100D-103 * : Multiple types of evaluation MCUs are available depending on their applications. Purchase the one that satisfies the service conditions. MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 6 2. Checking the Delivered Product Before using the MB2146-223, confirm that the following components are included in the box: ■ LQFP-64P (0.65 mm pitch) header board *1 :1 ■ Screws for securing header board (M2 × 10 mm, 0.4 mm pitch) :4 ■ NQPACK064SB *2 :1 *3 ■ HQPACK064SB140 ■ Operation manual (English version, this manual) :1 :1 *1: Header board manufactured by Tokyo Eletech Corporation, referred to as “YQPACK”, mounts YQPACK064SB. *2: IC socket manufactured by Tokyo Eletech Coporation, referred to as “NQPACK”, is supplied with a special screwdriver and 2 guide pins. A socket offering higher reliability, NQPACK064SB-SL (manufactured by Tokyo Eletech Corporation and sold separately) , can be used by making an IC socket mounting hole on the user system board. For more information, contact Tokyo Eletech Corporation. *3: IC socket cover manufactured by Tokyo Eletech Corporation, referred to as “HQPACK”, is supplied with 4 screws for securing HQPACK (M2 × 6 mm, 0.4 mm pitch) . MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 7 3. Handling Precautions The header board is precision-manufactured to improve the dimensional accuracy and to ensure a reliable contact. The header board is therefore sensitive to mechanical shocks. To ensure a correct use of the header board in the proper environment, observe the following: ■ Avoid placing a stress on the NQPACK mounted on the user system board when connecting the header board. MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 8 4. 4.1 Notes on Designing Notes on Designing Printed Circuit Board for the User System When the header board is connected to the user system, some part mounted around the NQPACK in the user system may be contacting the header board if the height of the part is tall. To prevent this, design the printed circuit board for the user system so that the components do not exceed the height shown in Figure 4-1. Figure 4-1 shows the dimension figure of the header board. Figure 4-1. Header Board Dimensions PCW-1-1-1PW :MAC EIGHT 40.0 mm 30.0 mm 1 1 2 CN1 40.0 mm CN2 2 CN3 U1 119 120 119 120 WR-120SB-VF-N1 : JAE *2 YQPACK064SB :Tokyo Eletech Corporation 13.0 mm *1 Approximately WR-120SB-VF-N1 : JAE *2 NQPACK064SB :Tokyo Eletech Corporation U1: User system I/F connector CN3: Incorrect insertion prevention socket CN1/CN2: MCU board I/F connector *1: The height differs slightly depending on how the YQPACK and NQPACK are engaged. *2: Japan Aviation Electronics Industry, Limited MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 9 Notes on Designing 4.2 MCU Footprint Design Notes Figure 4-2 shows the recommended footprint dimensions of the NQPACK mounted on the printed circuit board for the user system. Take the footprint in Figure 4-2 into consideration as well as the footprint of the mass production MCU when designing the printed circuit board for the user system. To follow the most updated information, be sure to contact Tokyo Eletech Corporation whenever designing the printed circuit board. 0.65 mm 0.4 mm 1.8 mm Figure 4-2. Recommended Footprint Dimensions for Mounting the NQPACK MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 15.6 mm 12.0 mm No.1 Pin 10 5. 5.1 Connecting to the User System Connecting Mount the supplied NQPACK on the user system before using the MB2146-223. 1. To connect the header board to the user system, match pin 1 indicated by the index mark (▲) on the NQPACK mounted on the user system with pin 1 indicated by the index mark (an angle cut linearly at one place only in silk screen) on the header board and then insert it (see Figure 5-1) . The pins of YQPACK are thin and easy to bend. Insert NQPACK after confirming that the pins of YQPACK are not bent. 33 16 64 17 49 32 48 1 Figure 5-1. Index Position NQPACK index mark Header board index mark 2. Insert each screw for securing the header board into each of the four tapped holes on the header board, and then tighten the screws diagonally. The center screw hole is not used. To tighten the screws, use the special screwdriver supplied with the NQPACK to equally tighten the four screws in sequence. Tightening the screws too tight might result in a defective contact. 3. Connect the MCU board to the header board while being careful not to excessively force the NQPACK. The MCU board can be connected to the header board only in the correct orientation as they have an incorrect insertion prevention header socket to prevent a reverse connection. Figure 5-2 illustrates how the MCU board, header board, NQPACK, and user system are connected together. MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 11 Connecting to the User System Figure 5-2. Connecting MCU Board/Header Board to User System MCU board Evaluation MCU MCU board Screws for securing header board Header board Connected at shipment YQPACK ÅNQPACK User system 5.2 Disconnection 1. Remove the MCU board from the header board. Detach the four corners slowly in sequence, not excessively forcing the junction with the NQPACK. 2. Remove all of the four screws from the header board. Pull out the header board vertically from the NQPACK. Remove the header board slowly not excessively forcing the junction with the NQPACK. MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 12 6. 6.1 Mounting Mass Production MCUs Mounting To mount a mass production MCU on the user system, use the supplied HQPACK (IC socket cover) (see “Figure 6-1”) . 1. To mount a mass production MCU on the user system, match the index mark (▲) on the NQPACK mounted on the user system with the index mark (●) on the mass production MCU. 2. Confirm that the mass production MCU is correctly mounted on the NQPACK. Next, match the index mark of HQPACK with the index mark of NQPACK and insert it (angle cut linearly at one place only) . The pins of HQPACK are thin and easy to bend. Insert NQPACK after confirming that pins of HQPACK are not bent. 3. Insert each screw for securing HQPACK in each of four tapped holes on the HQPACK, and then tighten the screws diagonally. To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten the four screws in sequence. Tightening the screws too tight might result in a defective contact. Figure 6-1. Mounting a Mass Production MCU Screws for securing HQPACK HQPACK Mass production MCU NQPACK User system MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 13 Mounting Mass Production MCUs 6.2 Disconnection To remove the HQPACK, remove all of the four screws and pull out the HQPACK vertically from the NQPACK. When taking out the mass production MCU, absorb the mass production MCU using a vacuum pick-up tool special for removing IC. Do not attempt to remove the mass production MCU forcibly, for example, using a screwdriver to do so can bend the pins of the mass production MCU or break the NQPACK. MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 14 7. 7.1 Product Specifications General Specifications Table 7-1 lists the general specifications of the header board. Table 7-1. General Specifications Item Description Operating temperature and storage temperature 5°C to 35°C (operation) , 0°C to 40°C (storage) Operating humidity and storage humidity 20 % to 80 % (operation) , 20 % to 80 % (storage) Approximately 40 mm × 40 mm × 16 mm Dimensions 7.2 (Height contains that of YQPACK and NQPACK) Main Part The main part of a header board is shown in Table 7-2. Table 7-2. Main Part Name Description 120 pin, 0.5 mm pitch, 2-piece connector MCU board I/F connector (straight) × 2 [Model number : WR-120SB-VF-N1 (from Japan Aviation Electronics Industry, Limited) ] 2 pin, 2.54 mm pitch, 1-piece socket Incorrect insertion prevention socket (Straight) [Model number : PCW-1-1-1PW (from MAC EIGHT) ] Socket User target system I/F connector 64 pin, 0.65 mm pitch [Model number : YQPACK064SB (from Tokyo Eletech Corporation) ] MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 15 Product Specifications 7.3 Functional Block Diagram A header board performs socket conversion between the MCU board I/F connector and YQPACK. The header board does not contain any component such as an IC internally. Figure 7-1 shows the block diagram. Figure 7-1. Functional Block Diagram MCU board I/F connector User target system I/F connector (Socket for package) MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 16 Product Specifications ■ MCU Board I/F Connector (CN1, CN2, and CN3) CN1 and CN2 are MCU board I/F connectors. CN3 is the incorrect insertion prevention socket of a MCU board. The pin assignment of the MCU board I/F connector CN1 is shown in Table 7-3, and the pin assignment of the MCU board I/F connector CN2 is shown in Table 7-4. Table 7-3. Pin Assignment of the MCU Board I/F Connector CN1 Connector Pin Number Evaluation MCU Pin Number Signal name Connector Pin Number Evaluation MCU Pin Number 1 A9 PC4 41 E2 2 B9 PC1 42 E1 Connector Pin Number Evaluation MCU Pin Number LVR3 81 P3 BSOUT LVSS 82 P4 BDBMX Signal name Signal name 3 C9 PC2 43 F4 LVDREXT 83 R1 P83 4 D9 PC3 44 F3 LVDBGR 84 R2 BRSTX 5 A8 PC0 45 F2 LVDENX 85 R3 X0A 6 B8 PB4 46 F1 P22A 86 R4 RSTX 7 C8 PB5 47 - GND 87 T1 ROMS1 8 D8 PB6 48 - GND 88 T2 BSIN 9 A7 PB7 49 G4 P20A 89 T3 Vss 10 B7 PB2 50 G3 NC1 90 T4 X0 11 C7 PB0 51 G2 P21A 91 U1 BEXCK 12 D7 PB1 52 G1 P23A 92 U2 X1 13 A6 PB3 53 H4 P24A 93 U3 MOD 14 B6 PA2 54 H3 P25A 94 U4 PF2 15 C6 P95 55 H2 P26A 95 V1 X1A 16 D6 PA0 56 H1 P27A 96 V2 Vcc53 17 A5 PA3 57 J4 P24B 97 - GND 18 B5 P94 58 J3 P50 98 - GND 19 C5 P90 59 J2 P23B 99 V3 PINT0 20 D5 P91 60 J1 P51 100 V4 PSEL_EXT 21 A4 PA1 61 K1 P52 101 R5 PF1 22 A3 P93 62 K2 P55 102 T5 PF0 23 - GND 63 K3 P54 103 U5 NC2 24 - GND 64 K4 P53 104 V5 PENABLE 25 A2 CSVENX 65 L1 P70 105 R6 APBENX 26 A1 Vss 66 L2 P74 106 T6 PINT1 27 B4 P92 67 L3 P73 107 U6 PCLK 28 B3 TCLK 68 L4 P72 108 V6 PADDR0 29 B2 LVCC 69 M1 P71 109 R7 PACTIVE 30 B1 LVDIN 70 M2 P76 110 T7 PLOCK 31 C4 Cpin 71 M3 P80 111 U7 PWRITE 32 C3 Vcc51 72 M4 P77 112 V7 PADDR1 33 C2 LVDENX2 73 - GND 113 R8 PADDR2 PADDR3 34 C1 LVR4 74 - GND 114 T8 35 D4 TESTO 75 N1 P75 115 U8 PADDR4 36 D3 LVDOUT 76 N2 P82 116 V8 PADDR5 37 D2 LVR2 77 N3 PG0 117 R9 PADDR7 38 D1 BGOENX 78 N4 P84 118 T9 PRDATA0 39 E4 LVR1 79 P1 P81 119 U9 PADDR6 40 E3 LVR0 80 P2 ROMS0 120 V9 PRDATA1 MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 17 Product Specifications Table 7-4. Pin Assignment of the MCU Board I/F Connector CN2 Connector Pin Number Evaluation MCU Pin Number Signal name Connector Pin Number Evaluation MCU Pin Number 1 A10 PC5 41 E17 NC4 2 B10 PD0 42 E18 SEL0 3 C10 PC6 43 F15 SEL3 4 D10 PC7 44 F16 SEL4 5 A11 PD1 45 F17 SEL1 85 R16 P31 6 B11 PD2 46 F18 P04C 86 R15 AVcc3 7 C11 PD3 47 - GND 87 T18 P40 8 D11 PD4 48 - GND 88 T17 P32 Signal name Connector Pin Number Evaluation MCU Pin Number Signal name 81 P16 P34 82 P15 P35 83 R18 P44 84 R17 P36 9 A12 PD5 49 G15 P06C 89 T16 AVss 10 B12 PD7 50 G16 P07C 90 T15 AVR 11 C12 P61 51 G17 P05C 91 U18 P33 12 D12 P60 52 G18 P00C 92 U17 P30 13 A13 PD6 53 H15 P01C 93 U16 AVR3 14 B13 P64 54 H16 P02C 94 U15 P15 15 C13 P66 55 H17 P03C 95 V18 AVcc 16 D13 P65 56 H18 P07A 96 V17 DA0 17 A14 P62 57 J15 P04A 97 - GND 18 B14 PE0A 58 J16 P05A 98 - GND 19 C14 PE3A 59 J17 P06A 99 V16 P14 20 D14 PE2A 60 J18 P03A 100 V15 P10 21 A15 P63 61 K18 P02A 101 R14 P16 22 A16 P67 62 K17 P07B 102 T14 DA1 23 - GND 63 K16 P01A 103 U14 P13 24 - GND 64 K15 P00A 104 V14 PWDATA7 25 A17 PE4A 65 L18 P06B 105 R13 P11 26 A18 Vcc54 66 L17 P05B 106 T13 P12 27 B15 PE1A 67 L16 P04B 107 U13 NC3 28 B16 PE5A 68 L15 P03B 108 V13 PWDATA3 29 B17 PE7A 69 M18 P02B 109 R12 PWDATA5 30 B18 PE3B 70 M17 P00B 110 T12 PWDATA6 31 C15 PE6A 71 M16 P46 111 U12 PWDATA4 32 C16 Vss 72 M15 P47 112 V12 PRDATA7 33 C17 PE2B 73 - GND 113 R11 PWDATA0 34 C18 PE7B 74 - GND 114 T11 PWDATA1 35 D15 PE1B 75 N18 P01B 115 U11 PWDATA2 36 D16 PE0B 76 N17 P43 116 V11 PRDATA6 37 D17 PE6B 77 N16 P41 117 R10 PRDATA3 38 D18 SEL2 78 N15 P42 118 T10 PRDATA4 39 E15 PE5B 79 P18 P45 119 U10 PRDATA5 40 E16 PE4B 80 P17 P37 120 V10 PRDATA2 MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 18 Product Specifications 7.4 User System I/F YQPACK (U1) The pin assignment of user system I/F YQPACK in the header board is shown in Table 7-5. Table 7-5. Pin Assignment of the User System I/F YQPACK in Header Board Connector Pin Number Signal name Connector Pin Number Signal name 1 AVCC 33 PB1/S01 2 AVR 34 PB2/S02 3 P14/PPG0 35 PB3/S03 4 P13/TRG0/ADTG 36 PB4/S04 5 P12/UCK0 37 PB5/S05 6 P11/UO0 38 PB6/S06 7 P10/UI0 39 PB7/S07 8 P24/EC0/SDA0 40 PC0/S08 9 P23/TO01/SCL0 41 PC1/S09 10 P22/TO00 42 PC2/S10 11 P21/PPG01 43 PC3/S11 12 P20/PPG00 44 PC4/S12 13 MOD 45 PC5/S13 14 X0 46 PC6/S14 15 X1 47 PC7/S15 16 VSS 48 P60/S16/PPG10 17 VCC 49 P61/S17/PPG11 18 PG0/(Cpin) 50 P62/S18/TO10 19 X1A 51 P63/S19/TO11 20 X0A 52 P64/S20/EC1 21 RSTX/FTEST 53 P65/S21/SCK 22 P90/V3 54 P66/S22/SOT 23 P91/V2 55 P67/S23/SIN 24 P92/V1 56 P07/INT07/AN07/S24 25 P93/V0 57 P06/INT06/AN06/S25 26 P94/C0 58 P05/INT05/AN05/S26 27 P95/C1 59 P04/INT04/AN04/S27 28 PA0/COM0 60 P03/INT03/AN03/S28 29 PA1/COM1 61 P02/INT02/AN02/S29 30 PA2/COM2 62 P01/INT01/AN01/S30 31 PA3/COM3 63 P00/INT00/AN00/S31 32 PB0/S00 64 AVSS MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 19 Revision History Document Revision Document Title: MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide Document Number: 002-07484 Revision ** *A ECN# Issue Date Origin of Change Description of Change 02/20/2009 HUAL Initial release 5285943 05/27/2016 HUAL Migrated Spansion Guide from SS01-26020-2E to Cypress format MB2146-223 F2MC-8FX Family LQFP-64P (0.65 mm pitch) Header Board Operation Guide, Doc. # 002-07484 Rev. *A 20