CYRF69103:低消費電力プログラマブルラジオオンチップ

CYRF69103
Programmable Radio on Chip Low Power
Programmable Radio on Chip Low Power
PRoC™ LP Features
■
Single Device, Two Functions
❐ 8-bit Flash based MCU function and 2.4 GHz radio
transceiver function in a single device.
■
Flash Based Microcontroller Function
❐ M8C based 8-bit CPU, optimized for Human Interface
Devices (HID) applications
❐ 256 Bytes of SRAM
❐ 8 Kbytes of Flash memory with EEPROM emulation
❐ In-System reprogrammable
❐ CPU speed up to 12 MHz
❐ 16-bit free running timer
❐ Low power wakeup timer
❐ 12-bit Programmable Interval Timer with interrupts
❐ Watchdog timer
■
Programmable output power up to +4 dBm
Auto Transaction Sequencer (ATS)
❐ Framing CRC and Auto ACK
❐ Received Signal Strength Indication (RSSI)
❐ Automatic Gain Control (AGC)
❐
❐
Industry leading 2.4 GHz Radio Transceiver Function
❐ Operates in the unlicensed worldwide Industrial, Scientific,
and Medical (ISM) band (2.4 GHz to 2.483 GHz)
❐ DSSS data rates of up to 250 Kbps
❐ GFSK data rate of 1 Mbps
❐ –97 dBm receive sensitivity
■
Component Reduction
❐ Integrated 1.8 V boost converter
❐ GPIOs that require no external components
❐ Operates off a single crystal
■
Flexible I/O
❐ 2 mA source current on all GPIO pins. Configurable 8 mA or
50 mA/pin current sink on designated pins
❐ Each GPIO pin supports high impedance inputs, configurable
pull up, open drain output, CMOS/TTL inputs, and CMOS
output
❐ Maskable interrupts on all I/O pins
■
Operating Voltage from 1.8 V to 3.6 V DC
■
Operating Temperature from 0 to 70 °C
■
Pb-free 40-pin QFN Package
■
Advanced Development Tools based on Cypress’s PSoC®
Tools
Logic Block Diagram
nSS
VCC
SCK
MOSI
47µF
VCC
470nF
VIO
VCC3
VCC2
VReg
VCC1
L/D
VBat0
VBat1
VBat2
RST
VDD_MICRO
10 µF
RFbias
RFp
RFn
Microcontroller
Function
IRQ/GPIO
P1.5/MOSI
4
MISO/GPIO
P1.4/SCK
P1_0:2,6:7
5
XOUT/GPIO
P1.3/nSS
PACTL/GPIO
12 MHz
Cypress Semiconductor Corporation
Document Number: 001-07611 Rev *I
•
198 Champion Court
•
.....
GND
GND
Xtal
GND
RESV
P2_0:1
2
.......
Vdd
P0_1,3,4,7
Radio
Function
470 nF
San Jose, CA 95134-1709
•
408-943-2600
Revised February 25, 2013
CYRF69103
Contents
Applications ...................................................................... 3
Functional Description ..................................................... 3
Functional Overview ........................................................ 3
2.4 GHz Radio Function .............................................. 3
Data Transmission Modes ........................................... 3
Microcontroller Function .............................................. 3
Backward Compatibility ............................................... 4
DDR Mode ................................................................... 4
SDR Mode .................................................................. 5
Pinouts .............................................................................. 6
Pin Definitions .................................................................. 6
Functional Block Overview .............................................. 7
2.4 GHz Radio ............................................................. 7
Frequency Synthesizer ................................................ 7
Baseband and Framer ................................................. 7
Packet Buffers and Radio Configuration Registers ..... 8
Auto Transaction Sequencer (ATS) ............................ 8
Interrupts ..................................................................... 9
Clocks .......................................................................... 9
GPIO Interface ............................................................ 9
Power On Reset/Low Voltage Detect .......................... 9
Timers ......................................................................... 9
Power Management .................................................... 9
Low Noise Amplifier (LNA) and
Received Signal Strength Indication (RSSI) ..................... 11
Receive Spurious Response ..................................... 11
SPI Interface .................................................................... 11
3-Wire SPI Interface .................................................. 11
4-Wire SPI Interface .................................................. 11
SPI Communication and Transactions ...................... 12
SPI I/O Voltage References ...................................... 12
SPI Connects to External Devices ............................ 12
CPU Architecture ............................................................ 13
CPU Registers ................................................................. 14
Flags Register ........................................................... 14
Accumulator Register ................................................ 14
Index Register ........................................................... 15
Stack Pointer Register ............................................... 15
CPU Program Counter High Register ....................... 15
CPU Program Counter Low Register ........................ 15
Addressing Modes ......................................................... 16
Source Immediate ..................................................... 16
Source Direct ............................................................. 16
Source Indexed ......................................................... 16
Destination Direct ...................................................... 16
Destination Indexed ................................................... 17
Destination Direct Source Immediate ........................ 17
Destination Indexed Source Immediate .................... 17
Destination Direct Source Direct ............................... 17
Source Indirect Post Increment ................................. 18
Destination Indirect Post Increment .......................... 18
Instruction Set Summary ............................................... 19
Memory Organization ..................................................... 20
Document Number: 001-07611 Rev *I
Flash Program Memory Organization ....................... 20
Data Memory Organization ....................................... 21
Flash .......................................................................... 21
SROM ........................................................................ 21
SROM Function Descriptions .................................... 22
Clocking .......................................................................... 25
SROM Table Read Description ................................. 26
Clock Architecture Description .................................. 27
CPU Clock During Sleep Mode ................................. 31
Reset ................................................................................ 32
Power On Reset ........................................................ 33
Watchdog Timer Reset .............................................. 33
Sleep Mode ...................................................................... 33
Sleep Sequence ........................................................ 33
Low Power in Sleep Mode ......................................... 34
Wakeup Sequence .................................................... 34
Low Voltage Detect Control ........................................... 36
POR Compare State ................................................. 37
ECO Trim Register .................................................... 37
General Purpose I/O Ports ............................................. 38
Port Data Registers ................................................... 38
GPIO Port Configuration ........................................... 39
GPIO Configurations for Low Power Mode ............... 44
Serial Peripheral Interface (SPI) ................................ 45
SPI Data Register ...................................................... 46
SPI Configure Register .............................................. 46
SPI Interface Pins ...................................................... 48
Timer Registers .............................................................. 48
Registers ................................................................... 48
Interrupt Controller ......................................................... 51
Architectural Description ........................................... 51
Interrupt Processing .................................................. 52
Interrupt Latency ....................................................... 52
Interrupt Registers ..................................................... 52
Microcontroller Function Register Summary ............. 56
Radio Function Register Summary ............................... 58
Absolute Maximum Ratings .......................................... 59
DC Characteristics ......................................................... 59
AC Characteristics ......................................................... 61
RF Characteristics .......................................................... 65
Ordering Information ...................................................... 67
Ordering Code Definitions ......................................... 67
Package Handling ........................................................... 68
Package Diagram ............................................................ 68
Acronyms ........................................................................ 70
Document Conventions ................................................. 70
Units of Measure ....................................................... 70
Document History Page ................................................. 71
Sales, Solutions, and Legal Information ...................... 72
Worldwide Sales and Design Support ....................... 72
Products .................................................................... 72
PSoC Solutions ......................................................... 72
Page 2 of 72
CYRF69103
Applications
The CYRF69103 PRoC LP is targeted for the following
applications:
■
■
Wireless HID devices:
❐ Mice
❐ Remote Controls
❐ Presenter tools
❐ Barcode scanners
❐ POS terminal
General purpose wireless applications:
❐ Industrial applications
❐ Home automation
❐ White goods
❐ Consumer electronics
❐ Toys
The radio meets
requirements:
Communication between the microcontroller and the radio is
through the radio’s SPI interface.
Functional Overview
The CYRF69103 is a complete Radio System-on-Chip device,
providing a complete RF system solution with a single device and
a few discrete components. The CYRF69103 is designed to
implement low cost wireless systems operating in the worldwide
2.4 GHz Industrial, Scientific, and Medical (ISM) frequency band
(2.400 GHz to 2.4835 GHz).
2.4 GHz Radio Function
The SoC contains a 2.4 GHz 1 Mbps GFSK radio transceiver,
packet data buffering, packet framer, DSSS baseband controller,
Received Signal Strength Indication (RSSI), and SPI interface
for data transfer and device configuration.
The radio supports 98 discrete 1 MHz channels (regulations may
limit the use of some of these channels in certain jurisdictions).
In
DSSS modes the
baseband
performs
DSSS
spreading/despreading, while in GFSK Mode (1 Mb/s - GFSK)
the baseband performs Start of Frame (SOF), End of Frame
(EOF) detection, and CRC16 generation and checking. The
baseband may also be configured to automatically transmit
Acknowledge (ACK) handshake packets whenever a valid
packet is received.
When in receive mode, with packet framing enabled, the device
is always ready to receive data transmitted at any of the
supported bit rates, except SDR, enabling the implementation of
mixed-rate systems in which different devices use different data
rates. This also enables the implementation of dynamic data rate
systems, which use high data rates at shorter distances and/or
in a low moderate interference environment, and change to lower
data rates at longer distances and/or in high interference
environments.
Document Number: 001-07611 Rev *I
following
■
Europe:
❐ ETSI EN 301 489-1 V1.4.1
❐ ETSI EN 300 328-1 V1.3.1
■
North America:
❐ FCC CFR 47 Part 15
■
Japan:
❐ ARIB STD-T66
worldwide
regulatory
Data Transmission Modes
The radio supports four different data transmission modes:
■
In GFSK mode, data is transmitted at 1 Mbps, without any
DSSS
■
In 8DR mode, 1 byte is encoded in each PN code symbol
transmitted
■
In DDR mode, 2 bits are encoded in each PN code symbol
transmitted
■
In SDR mode, a single bit is encoded in each PN code symbol
transmitted
Functional Description
PRoC LP devices are integrated radio and microcontroller
functions in the same package to provide a dual-role single-chip
solution.
the
Both 64-chip and 32-chip data PN codes are supported. The four
data transmission modes apply to the data after the Start of
Packet (SOP). In particular, the packet length, data and CRC are
all sent in the same mode.
Microcontroller Function
The MCU function is an 8-bit Flash-programmable
microcontroller. The instruction set is optimized specifically for
HID and a variety of other embedded applications.
The MCU function has up to 8 Kbytes of Flash for user’s code
and up to 256 bytes of RAM for stack space and user variables.
In addition, the MCU function includes a Watchdog timer, a
vectored interrupt controller, a 16-bit Free Running Timer, and
12-bit Programmable Interrupt Timer.
The microcontroller has 15 GPIO pins grouped into multiple
ports. With the exception of the four radio function GPIOs, each
GPIO port supports high impedance inputs, configurable pull up,
open drain output, CMOS/TTL inputs and CMOS output. Up to
two pins support programmable drive strength of up to 50 mA.
Additionally, each I/O pin can be used to generate a GPIO
interrupt to the microcontroller. Each GPIO port has its own GPIO
interrupt vector with the exception of GPIO Port 0. GPIO Port 0
has two dedicated pins that have independent interrupt vectors
(P0.3–P0.4).
The microcontroller features an internal oscillator.
The PRoC LP includes a Watchdog timer, a vectored interrupt
controller, a 12-bit programmable interval timer with configurable
1 ms interrupt and a 16-bit free running timer.
In addition, the CYRF69103 IC has a Power Management Unit
(PMU), which enables direct connection of the device to any
battery voltage in the range 1.8 V to 3.6 V. The PMU conditions
the battery voltage to provide the supply voltages required by the
device and may supply external devices.
Page 3 of 72
CYRF69103
Backward Compatibility
The CYRF69103 IC is fully interoperable with the main modes of
the first generation Cypress radios namely the CYWUSB6934
-LS and CYWWUSB6935-LR devices. The 62.5 kbps mode is
supported by selecting 32 chip DDR mode. Similarly, the
15.675 kbps mode is supported by selecting 64 chip SDR mode
In this method, a suitably configured CYRF69103 IC device may
transmit data to or receive data from a first generation device, or
both. Backwards compatibility requires disabling the SOP,
length, and CRC16 fields.
This section provides the different configurations of the registers
and firmware that enable a new generation radio to communicate
with a first generation radio. There are two possible modes: SDR
and DDR mode (8-DR and GFSK modes are not present in the
first generation radio). The second generation radio must be
initialized using the RadioInitAPI of the LP radio driver and then
the following registers’ bits need to be configured to the given
Byte values. Essentially, the following deactivates the added
features of the second generation radio and takes it down to the
level of the first generation radio. The data format, data rates,
and the PN codes used are recognizable by the first generation
radio.
DDR Mode
Table 1. DDR Mode
Register
Value
Description
TX_CFG_ADR
0X16
32 chip PN Code, DDR, PA = 6
RX_CFG_ADR
0X4B
AGC is enabled. LNA and attenuator are disabled. Fast turnaround is disabled, the device
uses high side receive injection and Hi-Lo is disabled. Overwrite to receive buffer is
enabled and the RX buffer is configured to receive eight bytes maximum.
XACT_CFG_ADR
0X05
AutoACK is disabled. Forcing end state is disabled. The device is configured to transition
to Idle mode after a Receive or Transmit. ACK timeout is set to 128 µs.
FRAMING_CFG_ADR
0X00
All SOP and framing features are disabled. Disable LEN_EN = 0 if EOP is needed.
TX_OVERRIDE_ADR
0X04
Disable Transmit CRC-16.
RX_OVERRIDE_ADR
0X14
The receiver rejects packets with a zero seed. The Rx CRC-16 Checker is disabled and
the receiver accepts bad packets that do not match the seed in CRC_seed registers. This
helps in communication with the first generation radio that does not have CRC capabilities.
ANALOG_CTRL_ADR
0X01
Set ALL SLOW. When set, the synthesizer settle time for all channels is the same as the
slow channels in the first generation radio.
DATA32_THOLD_ADR
0X03
Sets the number of allowed corrupted bits to 3.
EOP_CTRL_ADR
0x01
Sets the number of consecutive symbols for non-correlation to detect end of packet.
PREAMBLE_ADR
0xAAAA05
Document Number: 001-07611 Rev *I
AAAA are the two preamble bytes. Any other byte can also be written into the preamble
register file. Recommended counts of the preamble bytes to be sent must be >4.
Page 4 of 72
CYRF69103
SDR Mode
Table 2. SDR Mode
Register
Value
Description
TX_CFG_ADR
0X3E
64 chip PN code, SDR mode, PA = 6
RX_CFG_ADR
0X4B
AGC is enabled. LNA and attenuator are disabled. Fast turnaround is disabled, the device
uses high side receive injection and Hi-Lo is disabled. Overwrite to receive buffer is
enabled and RX buffer is configured to receive eight bytes maximum. Enables RXOW to
allow new packets to be loaded into the receive buffer. This also enables the VALID bit
which is used by the first generation radio’s error correction firmware.
XACT_CFG_ADR
0X05
AutoACK is disabled. Forcing end state is disabled. The device is configured to transition
to Idle mode after Receive or Transmit. ACK timeout is set to 128 µs.
FRAMING_CFG_ADR
0X00
All SOP and framing features are disabled. Disable LEN_EN=0 if EOP is needed.
TX_OVERRIDE_ADR
0X04
Disable Transmit CRC-16.
RX_OVERRIDE_ADR
0X14
The receiver rejects packets with a zero seed. The RX CRC-16 checker is disabled and
the receiver accepts bad packets that do not match the seed in the CRC_seed registers.
This helps in communication with the first generation radio that does not have CRC
capabilities.
ANALOG_CTRL_ADR
0X01
Set ALL SLOW. When set, the synthesizer settle time for all channels is the same as the
slow channels in the first generation radio, for manual ACK consistency
DATA64_THOLD_ADR
0X07
Sets the number of allowed corrupted bits to 7 which is close to the recommended 12%
value.
EOP_CTRL_ADR
0xA1
Sets the number of consecutive symbols for non-correlation to detect end of packet.
PREAMBLE_ADR
0xAAAA09
Document Number: 001-07611 Rev *I
AAAA are the two preamble bytes. Any other byte can also be written into the preamble
register file. Recommended counts of the preamble bytes to be sent must be >8.
Page 5 of 72
CYRF69103
Pinouts
Figure 1. Pin Diagram
PACTL / GPIO 31
VIO 33
P1.6 32
RST 34
36
P1.7 35
VDD_1.8
L/D 37
P0.7 38
VREG 40
VBAT0 39
Corner
tabs
P0.4
1
30 XOUT / GPIO
XTAL
2
VCC
3
P0.3
4
P0.1
5
26 P1.4 / SCK
VBAT1
6
25 P1.3 / SS
VCC
7
24 P1.2
P2.1
8
23 VDD_Micro
VBAT2
9
29 MISO / GPIO
CYRF69103
PRoC LP
28 P1.5 / MOSI
27 IRQ / GPIO
22 P1.1
* E-PAD Bottom Side
21 P1.0
RFBIAS 10
20 NC
19 RESV
18 NC
17 NC
16 VCC
15 P2.0
14 NC
13 RFN
12 GND
11 RFP
Pin Definitions
Pin
Name
1
P0.4
Individually configured GPIO
Description
12 MHz crystal
2
XTAL
3, 7, 16
VCC
2.4 V to 3.6 V supply. Connected to pin 40 (0.047 F bypass)
4
P0.3
Individually configured GPIO
5
P0.1
Individually configured GPIO
6
Vbat1
Connect to 1.8 V to 3.6 V power supply, through 47 ohm series/1 F shunt C.
8
P2.1
GPIO. Port 2 Bit 1
9
Vbat2
Connected to1.8 V to 3.6 V main power supply, through 0.047 F bypass C.
10
RFbias
RF pin voltage reference
11
RFp
Differential RF to or from antenna
12
GND
GND
13
RFn
Differential RF to or from antenna
14, 17, 18, 20
NC
15
P2.0
19
RESV
GPIO
21
P1.0
GPIO port 1 bit 0 / ISSP-SCLK
If this pin is used as a general-purpose output it draws current. It is, therefore, configured as an input
to reduce current draw.
22
P1.1
GPIO port 1 bit 1 / ISSP-SDATA
If this pin is used as a general-purpose output it draws current. It is, therefore, configured as an input
to reduce current draw.
23
VDD_micro
Reserved. Must connect to GND
MCU supply connected to pin 40, max CPU 12 MHz
Document Number: 001-07611 Rev *I
Page 6 of 72
CYRF69103
Pin Definitions (continued)
Pin
Name
24
P1.2
25
P1.3 / nSS
26
P1.4 / SCK
27
IRQ
28
Description
GPIO
Slave Select
SPI Clock
Radio Function Interrupt output, configure High, Low or as Radio GPIO.
P1.5 / MOSI MOSI pin from microcontroller function to radio function.
29
MISO
3-wire SPI mode configured as Radio GPIO. In 4-wire SPI mode sends data to MCU function.
30
XOUT
Buffered CLK, PACTL_n or Radio GPIO.
31
PACTL
Control for external PA or Radio GPIO.
32
P1.6
GPIO
33
VIO
1.8 V to 3.6V to main power supply rail for Radio I/O.
34
RST
Radio Reset. Connected to pin 40 with 0.47 F. Must have a RST = HIGH event the very first time
power is applied to the radio otherwise the state of the radio control registers is unknown.
35
P1.7
36
VDD1.8
GPIO
Regulated logic bypass. Connected to 0.47 F to GND.
37
L/D
Inductor/Diode connection for Boost. When Internal PMU is not being used connect L/D to GND.
38
P0.7
GPIO
39
Vbat0
Connected to1.8 V to 3.6 V main power supply, through 0.047 F bypass C.
40
VREG
Boost regulator output voltage feedback
E-pad
Must be connected to ground.
41
42
Corner Tabs Do Not connect corner tabs.
Functional Block Overview
Frequency Synthesizer
All the blocks that make up the PRoC LP are presented in this
section.
Before transmission or reception may commence, it is necessary
for the frequency synthesizer to settle. The settling time varies
depending on channel; 25 fast channels are provided with a
maximum settling time of 100 s.
2.4 GHz Radio
The radio transceiver is a dual conversion low IF architecture
optimized for power and range/robustness. The radio employs
channel matched filters to achieve high performance in the
presence of interference. An integrated Power Amplifier (PA)
provides up to +4 dBm transmit power, with an output power
control range of 34 dB in eight steps. The supply current of the
device is reduced as the RF output power is reduced.
Table 3. Internal PA Output Power Step Table
PA Setting
Typical Output Power (dBm)
7
+4
6
0
5
–5
4
–10
3
–15
2
–20
1
–25
0
–30
Document Number: 001-07611 Rev *I
The “fast channels” (<100 s settling time) are every 3rd
frequency, starting at 2400 MHz up to and including 2472 MHz
(that is, 0,3,6,9…….69 and 72).
Baseband and Framer
The baseband and framer blocks provide the DSSS encoding
and decoding, SOP generation and reception and CRC16
generation and checking, and EOP detection and length field.
Data Transmission Modes and Data Rates
The SoC supports four different data transmission modes:
■
In GFSK mode, data is transmitted at 1 Mbps, without any
DSSS.
■
In 8DR mode, 8 bits are encoded in each DATA_CODE_ADR
derived code symbol transmitted.
■
In DDR mode, 2 bits are encoded in each DATA_CODE_ADR
derived code symbol transmitted (as in the CYWUSB6934 DDR
mode).
■
In SDR mode, 1 bit is encoded in each DATA_CODE_ADR
derived code symbol transmitted (as in the CYWUSB6934
standard modes).
Page 7 of 72
CYRF69103
Both 64-chip and 32-chip DATA_CODE_ADR codes are
supported. The four data transmission modes apply to the data
after the SOP. In particular the length, data, and CRC16 are all
sent in the same mode. In general, lower data rates reduces
packet error rate in any given environment.
The CYRF69103 IC supports the following data rates:
■
1000 kbps (GFSK)
■
250 kbps (32-chip 8DR)
■
125 kbps (64-chip 8DR)
■
62.5 kbps (32-chip DDR)
■
31.25 kbps (64-chip DDR)
■
15.625 kbps (64-chip SDR)
Lower data rates typically provide longer range and/or a more
robust link.
Link Layer Modes
The CYRF69103 IC device supports the following data packet
framing features:
SOP – Packets begin with a 2-symbol Start of Packet (SOP)
marker. This is required in GFSK and 8DR modes, but is optional
in DDR mode and is not supported in SDR mode. If framing is
disabled then an SOP event is inferred whenever two successive
correlations are detected. The SOP_CODE_ADR code used for
the SOP is different from that used for the “body” of the packet,
and if desired may be a different length. SOP must be configured
to be the same length on both sides of the link.
EOP – There are two options for detecting the end of a packet.
If SOP is enabled, then a packet length field may be enabled.
GFSK and 8DR must enable the length field. This is the first
8 bits after the SOP symbol, and is transmitted at the payload
data rate. If the length field is enabled, an End of Packet (EOP)
condition is inferred after reception of the number of bytes
defined in the length field, plus two bytes for the CRC16 (if
enabled). The alternative to using the length field is to infer an
EOP condition from a configurable number of successive non
correlations; this option is not available in GFSK mode and is
only recommended when using SDR mode.
CRC16 – The device may be configured to append a 16-bit
CRC16 to each packet. The CRC16 uses the USB CRC
polynomial with the added programmability of the seed. If
enabled, the receiver verifies the calculated CRC16 for the
payload data against the received value in the CRC16 field. The
starting value for the CRC16 calculation is configurable, and the
CRC16 transmitted may be calculated using either the loaded
seed value or a zero seed; the received data CRC16 is checked
against both the configured and zero CRC16 seeds.
CRC16 detects the following errors:
Any one bit in error
■
■
Any two bits in error (no matter how far apart, which column,
and so on)
■
Any odd number of bits in error (no matter where they are)
■
An error burst as wide as the checksum itself
Figure 2 shows an example packet with SOP, CRC16 and
lengths fields enabled.
Figure 2. Example Default Packet Format
P re a m b le
n x 16us
2 n d F ra m in g
S y m b o l*
P
SOP 1
SOP 2
1 s t F ra m in g
S y m b o l*
L e n g th
Packet
le n g th
1 B y te
P e rio d
Packet Buffers and Radio Configuration Registers
Packet data and configuration registers are accessed through
the SPI interface. All configuration registers are directly
addressed through the address field in the SPI packet (as in the
CYWUSB6934). Configuration registers are provided to allow
configuration of DSSS PN codes, data rate, operating mode,
interrupt masks, interrupt status, and others.
Packet Buffers
All data transmission and reception use the 16-byte packet
buffers: one for transmission and one for reception.
The transmit buffer allows a complete packet of up to 16 bytes of
payload data to be loaded in one burst SPI transaction, and then
transmitted with no further MCU intervention. Similarly, the
receive buffer allows an entire packet of payload data up to 16
bytes to be received with no firmware intervention required until
packet reception is complete.
Document Number: 001-07611 Rev *I
C R C 16
P a y lo a d D a ta
* N o te :3 2 o r 6 4 u s
The CYRF69103 IC supports packet length of up to 40 bytes;
interrupts are provided to allow an MCU to use the transmit and
receive buffers as FIFOs. When transmitting a packet longer
than 16 bytes, the MCU can load 16 bytes initially, and add
further bytes to the transmit buffer as transmission of data
creates space in the buffer. Similarly, when receiving packets
longer than 16 bytes, the MCU must fetch received data from the
FIFO periodically during packet reception to prevent it from
overflowing.
Auto Transaction Sequencer (ATS)
The CYRF69103 IC provides automated support for
transmission and reception of acknowledged data packets.
When transmitting a data packet, the device automatically starts
the crystal and synthesizer, enters transmit mode, transmits the
packet in the transmit buffer, and then automatically switches to
receive mode and waits for a handshake packet – and then
Page 8 of 72
CYRF69103
automatically reverts to sleep mode or idle mode when either an
ACK packet is received, or a time out period expires.
Similarly, when receiving in transaction mode, the device waits
in receive mode for a valid packet to be received, then
automatically transitions to transmit mode, transmits an ACK
packet, and then switches back to receive mode to await the next
packet. The contents of the packet buffers are not affected by the
transmission or reception of ACK packets.
In each case, the entire packet transaction takes place without
any need for MCU firmware action; to transmit data the MCU
simply needs to load the data packet to be transmitted, set the
length, and set the TX GO bit. Similarly, when receiving packets
in transaction mode, firmware simply needs to retrieve the fully
received packet in response to an interrupt request indicating
reception of a packet.
Interrupts
The radio function provides an interrupt (IRQ) output, which is
configurable to indicate the occurrence of various different
events. The IRQ pin may be programmed to be either active high
or active low, and be either a CMOS or open drain output.
The radio function features three sets of interrupts: transmit,
receive, and system interrupts. These interrupts all share a
single pin (IRQ), but can be independently enabled/disabled. In
transmit mode, all receive interrupts are automatically disabled,
and in receive mode all transmit interrupts are automatically
disabled. However, the contents of the enable registers are
preserved when switching between transmit and receive modes.
If more than one radio interrupt is enabled at any time, it is
necessary to read the relevant status register to determine which
event caused the IRQ pin to assert. Even when a given interrupt
source is disabled, the status of the condition that would
otherwise cause an interrupt can be determined by reading the
appropriate status register. It is therefore possible to use the
devices without making use of the IRQ pin by polling the status
register(s) to wait for an event, rather than using the IRQ pin.
Clocks
A 12 MHz crystal (30 ppm or better) is directly connected
between XTAL and GND without the need for external
capacitors. A digital clock out function is provided, with
selectable output frequencies of 0.75, 1.5, 3, 6, or 12 MHz. This
output may be used to clock an external microcontroller (MCU)
or ASIC. This output is enabled by default, but may be disabled.
The requirements for the crystal to be directly connected to XTAL
pin and GND are:
■
Nominal Frequency: 12 MHz
■
Operating Mode: Fundamental Mode
■
Resonance Mode: Parallel Resonant
■
Frequency Initial Stability: ±30 ppm
■
Series Resistance: <60 ohms
■
Load Capacitance: 10 pF
■
Drive Level: l00 W
Document Number: 001-07611 Rev *I
The MCU function features an internal oscillator. The clock
generator provides the 12 MHz and 24 MHz clocks that remain
internal to the microcontroller.
GPIO Interface
The MCU function features up to 15 general purpose I/O (GPIO)
pins.The I/O pins are grouped into three ports (Port 0 to 2). The
pins on Port 0 and Port 1 may each be configured individually
while the pins on Port 2 may only be configured as a group. Each
GPIO port supports high-impedance inputs, configurable pull up,
open drain output, CMOS/TTL inputs, and CMOS output with up
to two pins that support programmable drive strength of up to
50 mA sink current. Additionally, each I/O pin can be used to
generate a GPIO interrupt to the microcontroller. Each GPIO port
has its own GPIO interrupt vector with the exception of GPIO
Port 0. GPIO Port 0 has three dedicated pins that have
independent interrupt vectors (P0.1, P0.3–P0.4).
Power On Reset/Low Voltage Detect
The power on reset circuit detects logic when power is applied
to the device, resets the logic to a known state, and begins
executing instructions at Flash address 0x0000. When power
falls below a programmable trip voltage, it generates reset or
may be configured to generate interrupt. There is a low voltage
detect circuit that detects when VCC drops below a
programmable trip voltage. It may be configurable to generate an
LVD interrupt to inform the processor about the low voltage
event. POR and LVD share the same interrupt. There is not a
separate interrupt for each. The Watchdog timer can be used to
ensure the firmware never gets stalled in an infinite loop.
Timers
The free running 16-bit timer provides two interrupt sources: the
programmable interval timer with 1-s resolution and the
1.024 ms outputs. The timer can be used to measure the
duration of an event under firmware control by reading the timer
at the start and at the end of an event, then calculating the
difference between the two values.
Power Management
The operating voltage of the device is 1.8V to 3.6V DC, which is
applied to the VBAT pin. The device can be shut down to a fully
static sleep mode by writing to the FRC END = 1 and
END STATE = 000 bits in the XACT_CFG_ADR register over the
SPI interface. The device enters sleep mode within 35 s after
the last SCK positive edge at the end of this SPI transaction.
Alternatively, the device may be configured to automatically
enter sleep mode after completing packet transmission or
reception. When in sleep mode, the on-chip oscillator is stopped,
but the SPI interface remains functional. The device wakes from
sleep mode automatically when the device is commanded to
enter transmit or receive mode. When resuming from sleep
mode, there is a short delay while the oscillator restarts. The
device may be configured to assert the IRQ pin when the
oscillator has stabilized.
The output voltage (VREG) of the Power Management Unit
(PMU) is configurable to several minimum values between 2.4 V
and 2.7 V. VREG may be used to provide up to 15 mA (average
load) to external devices. It is possible to disable the PMU, and
to provide an externally regulated DC supply voltage to the
Page 9 of 72
CYRF69103
Figure 3. PMU Enabled
device in the range 2.4 V to 3.6 V. The PMU also provides a
regulated 1.8 V supply to the logic.
VBat
The PMU has been designed to provide high boost efficiency
(74–85% depending on input voltage, output voltage and load)
when using a Schottky diode and power inductor, eliminating the
need for an external boost converter in many systems where
other components require a boosted voltage. However,
reasonable efficiencies (69–82% depending on input voltage,
output voltage and load) may be achieved when using low-cost
components such as SOT23 diodes and 0805 inductors.
VCC
1 Ohm 1%
0.047 µF
0.047 µF
1 µF
6.3V
0.047 µF
0.047µF
The current through the diode must stay within the linear
operating range of the diode. For some loads the SOT23 diode
is sufficient, but with higher loads it is not and a SS12 diode must
be used to stay within this linear range of operation. Along with
the diode, the inductor used must not saturate its core. In higher
loads, a lower resistance/higher saturation coil like the inductor
from Sumida must be used.
0.047 µF
VCC3
VCC2
VCC1
VReg
VIO
VBat0
VBat1
VBat2
0.047 µF
VDD
PRoC LP
VDD_MICRO
0.1µF
L/D
The PMU also provides a configurable low battery detection
function which may be read over the SPI interface. One of seven
thresholds between 1.8 V and 2.7 V may be selected. The
interrupt pin may be configured to assert when the voltage on the
VBAT pin falls below the configured threshold. LV IRQ is not a
latched event. Battery monitoring is disabled when the device is
in sleep mode.
10 µF
6.3V
47 Ohm
The following three figures show different examples of how to
use PRoC LP with and without the PMU. Figure 3 shows the
most common circuit making use of the PMU to boost battery
voltage up to 2.7 V. Figure 4 is an example of the circuit used
when the supply voltage is always above 2.7 V. This could be
three 1.5 V battery cells in series along with a linear regulator, or
some similar power source. Figure 5 shows an example of using
the PRoC LP with its PMU disabled and an external boost to
supply power to the device. This might be required when the load
is much greater than the 15 mA average load that PRoC can
support.
VBat
VCC
10 µH
100 µF 10V
BAT400D
10 µF 6.3V
Figure 4. PMU Disabled - Linear Regulator
VCC
0.047µF
0.047µF
0.047µF
0.047µF
0.047µF
0.047µF
0.047µF
VCC3
VCC2
VCC1
VReg
VIO
VBat0
VBat1
VBat2
0.047µF
VDD
VDD_MICRO
PRoC LP
L/D
0.1µF
Document Number: 001-07611 Rev *I
Page 10 of 72
CYRF69103
Figure 5. PMU Disabled - External Boost Converter
V Bat
External DC-DC
Boost Converter
1 Ohm 1%
0.047µF
SPI Interface
0.047µF
1µF
6.3V
0.047µF
0.047µF
0.047µF
VCC3
VCC2
VCC1
VReg
VIO
VBat0
VBat1
VBat2
0.047µF
VDD
VDD_MICRO
PRoC LP
L/D
0.1µF
Low Noise Amplifier (LNA) and Received Signal
Strength Indication (RSSI)
The gain of the receiver may be controlled directly by clearing
the AGC EN bit and writing to the Low Noise Amplifier (LNA) bit
of the RX_CFG_ADR register. When the LNA bit is cleared, the
receiver gain is reduced by approximately 20 dB, allowing
accurate reception of very strong received signals (for example
when operating a receiver very close to the transmitter). An
additional 20 dB of receiver attenuation can be added by setting
the Attenuation (ATT) bit; this allows data reception to be limited
to devices at very short ranges. Disabling AGC and enabling
LNA is recommended unless receiving from a device using
external PA.
The RSSI register returns the relative signal strength of the
on-channel signal power.
When receiving, the device may be configured to automatically
measure and store the relative strength of the signal being
received as a 5-bit value. When enabled, an RSSI reading is
taken and may be read through the SPI interface. An RSSI
reading is taken automatically when the start of a packet is
detected. In addition, a new RSSI reading is taken every time the
previous reading is read from the RSSI register, allowing the
background RF energy level on any given channel to be easily
measured when RSSI is read when no signal is being received.
A new reading can occur as fast as once every 12 s.
The SPI interface between the MCU function and the radio
function is a 3-wire SPI Interface. The three pins are MOSI
(Master Out Slave In), SCK (Serial Clock), SS (Slave Select).
There is an alternate 4-wire MISO Interface that requires the
connection of two external pins. The SPI interface is controlled
by configuring the SPI Configure Register. (SPICR Addr: 0x3D).
3-Wire SPI Interface
The radio function receives a clock from the MCU function on the
SCK pin. The MOSI pin is multiplexed with the MISO pin.
Bidirectional data transfer takes place between the MCU function
and the radio function through this multiplexed MOSI pin. When
using this mode the user firmware must ensure that the MOSI pin
on the MCU function is in a high impedance state, except when
the MCU is actively transmitting data. Firmware must also control
the direction of data flow and switch directions between MCU
function and radio function by setting the SWAP bit [Bit 7] of the
SPI Configure Register. The SS pin is asserted before initiating
a data transfer between the MCU function and the radio function.
The IRQ function may be optionally multiplexed with the MOSI
pin; when this option is enabled the IRQ function is not available
while the SS pin is low. When using this configuration, user
firmware must ensure that the MOSI function on MCU function
is in a high-impedance state whenever SS is high.
Figure 6. 3-Wire SPI Mode
MOSI
10µF
6.3V
47 Ohm
The workaround for this is to program an additional byte in the
packet header which contains the transmitter channel number.
After the packet is received, the channel number can be
checked. If the channel number does not match the receive
channel then the packet is rejected.
SCK
nSS
VCC
operating at the transmit spur frequency may receive the spur if
the spur level power is greater than the receive sensitivity level.
Radio Function
MCU Function
P1.5/MOSI
MOSI/MISO multiplexed
on one MOSI pin
MOSI
P1.4/SCK
SCK
P1.3/nSS
nSS
Receive Spurious Response
4-Wire SPI Interface
The transmitter may exhibit spurs around 50MHz offset at levels
approximately 50dB to 60dB below the carrier power. Receivers
The 4-wire SPI communications interface consists of MOSI,
MISO, SCK, and SS.
Document Number: 001-07611 Rev *I
Page 11 of 72
CYRF69103
The device receives SCK from the MCU function on the SCK pin.
Data from the MCU function is shifted in on the MOSI pin. Data
to the MCU function is shifted out on the MISO pin. The active
low SS pin must be asserted for the two functions to
communicate. The IRQ function may be optionally multiplexed
with the MOSI pin; when this option is enabled the IRQ function
is not available while the SS pin is low. When using this
configuration, user firmware must ensure that the MOSI function
on MCU function is in a high-impedance state whenever SS is
high.
P1.6/MISO
P1.5/MOSI
MOSI
P1.4/SCK
SCK
P1.3/nSS
nSS
The INC bit helps to read or write consecutive bytes from
contiguous memory locations in a single burst mode operation.
If Slave Select is asserted and INC = 1, then the master MCU
function reads a byte from the radio, the address is incremented
by a byte location, and then the byte at that location is read, and
so on.
The SPI interface between the radio function and the MCU is not
dependent on the internal 12 MHz oscillator of the radio.
Therefore, radio function registers can be read from or written
into while the radio is in sleep mode.
Radio Function
MCU Function
The DIR bit specifies the direction of data transfer. 0 = Master
reads from slave. 1 = Master writes to slave.
If Slave Select is asserted and INC = 0, then the MCU function
reads/writes the bytes in the same register in burst mode, but if
it is a register file then it reads/writes the bytes in that register file.
nSS
MOSI
SCK
Figure 7. 4-Wire SPI Mode
byte. The following bytes are data bytes. The SPI transaction
format is shown in Figure 4.
SPI I/O Voltage References
MISO
The SPI interfaces between MCU function and the radio and the
IRQ and RST have a separate voltage reference VIO. For
CYRF69103 VIO is normally set to VCC.
SPI Connects to External Devices
The three SPI wires, MOSI, SCK, and SS are also drawn out of
the package as external pins to allow the user to interface their
own external devices (such as optical sensors and others)
through SPI. The radio function also has its own SPI wires MISO
and IRQ, which can be used to send data back to the MCU
function or send an interrupt request to the MCU function. They
can also be configured as GPIO pins.
This connection is external to the PRoC LP Chip
SPI Communication and Transactions
The SPI transactions can be single byte or multi-byte. The MCU
function initiates a data transfer through a Command/Address
Table 4. SPI Transaction Format
Byte 1
Bit #
Bit Name
Byte 1+N
7
6
[5:0]
[7:0]
DIR
INC
Address
Data
Document Number: 001-07611 Rev *I
Page 12 of 72
CYRF69103
CPU Architecture
This family of microcontrollers is based on a high-performance,
8-bit, Harvard architecture microprocessor. Five registers control
the primary operation of the CPU core. These registers are
affected by various instructions, but are not directly accessible
through the register space by the user.
Table 5. CPU Registers and Register Name
Register
Register Name
Flags
CPU_F
Program Counter
CPU_PC
Accumulator
CPU_A
Stack Pointer
CPU_SP
Index
CPU_X
The 16-bit Program Counter Register (CPU_PC) allows for direct
addressing of the full eight Kbytes of program memory space.
Document Number: 001-07611 Rev *I
The Accumulator Register (CPU_A) is the general-purpose
register that holds the results of instructions that specify any of
the source addressing modes.
The Index Register (CPU_X) holds an offset value that is used
in the indexed addressing modes. Typically, this is used to
address a block of data within the data memory space.
The Stack Pointer Register (CPU_SP) holds the address of the
current top-of-stack in the data memory space. It is affected by
the PUSH, POP, LCALL, CALL, RETI, and RET instructions,
which manage the software stack. It can also be affected by the
SWAP and ADD instructions.
The Flag Register (CPU_F) has three status bits: Zero Flag bit
[1]; Carry Flag bit [2]; Supervisory State bit [3]. The Global
Interrupt Enable bit [0] is used to globally enable or disable
interrupts. The user cannot manipulate the Supervisory State
status bit [3]. The flags are affected by arithmetic, logic, and shift
operations. The manner in which each flag is changed is
dependent upon the instruction being executed (for example,
AND, OR, XOR). See Table 22 on page 19.
Page 13 of 72
CYRF69103
CPU Registers
Flags Register
The Flags Register can only be set or reset with logical instruction.
Table 6. CPU Flags Register (CPU_F) [R/W]
Bit #
7
Field
6
5
4
3
2
1
0
XIO
Super
Carry
Zero
Global IE
Read/Write
–
Reserved
–
–
R/W
R
RW
RW
RW
Default
0
0
0
0
0
0
1
0
Bits 7:5
Bit 4
Reserved
XIO
Set by the user to select between the register banks.
0 = Bank 0
1 = Bank 1
Bit 3
Super
Indicates whether the CPU is executing user code or Supervisor Code (This code cannot be accessed directly
by the user).
0 = User Code
1 = Supervisor Code
Bit 2
Carry
Set by CPU to indicate whether there has been a carry in the previous logical/arithmetic operation.
0 = No Carry
1 = Carry
Bit 1
Zero
Set by CPU to indicate whether there has been a zero result in the previous logical/arithmetic operation.
0 = Not Equal to Zero
1 = Equal to Zero
Bit 0
Global IE
Determines whether all interrupts are enabled or disabled.
0 = Disabled
1 = Enabled
Note This register is readable with explicit address 0xF7. The OR F, expr and AND F, expr must be used to set and clear the
CPU_F bits.
Accumulator Register
Table 7. CPU Accumulator Register (CPU_A)
Bit #
7
6
5
Field
4
3
2
1
0
CPU Accumulator [7:0]
Read/Write
–
–
–
–
–
–
–
–
Default
0
0
0
0
0
0
0
0
Bits 7:0
CPU Accumulator [7:0]
8-bit data value holds the result of any logical/arithmetic instruction that uses a source addressing mode.
Document Number: 001-07611 Rev *I
Page 14 of 72
CYRF69103
Index Register
Table 8. CPU X Register (CPU_X)
Bit #
7
6
5
4
Field
3
2
1
0
X [7:0]
Read/Write
–
–
–
–
–
–
–
–
Default
0
0
0
0
0
0
0
0
2
1
0
Bits 7:0
X [7:0]
8-bit data value holds an index for any instruction that uses an indexed addressing mode.
Stack Pointer Register
Table 9. CPU Stack Pointer Register (CPU_SP)
Bit #
7
6
5
4
Field
3
Stack Pointer [7:0]
Read/Write
–
–
–
–
–
–
–
–
Default
0
0
0
0
0
0
0
0
3
2
1
0
Bits 7:0
Stack Pointer [7:0]
8-bit data value holds a pointer to the current top-of-stack.
CPU Program Counter High Register
Table 10. CPU Program Counter High Register (CPU_PCH)
Bit #
7
6
5
Read/Write
–
–
–
–
–
–
–
–
Default
0
0
0
0
0
0
0
0
3
2
1
0
Field
4
Program Counter [15:8]
Bits 7:0
Program Counter [15:8]
8-bit data value holds the higher byte of the program counter.
CPU Program Counter Low Register
Table 11. CPU Program Counter Low Register (CPU_PCL)
Bit #
7
6
5
Field
4
Program Counter [7:0]
Read/Write
–
–
–
–
–
–
–
–
Default
0
0
0
0
0
0
0
0
Bit 7:0
Program Counter [7:0]
8-bit data value holds the lower byte of the program counter.
Document Number: 001-07611 Rev *I
Page 15 of 72
CYRF69103
Addressing Modes
Source Indexed
Examples of the different addressing modes are discussed in
this section and example code is given.
Source Immediate
The result of an instruction using this addressing mode is placed
in the A register, the F register, the SP register, or the X register,
which is specified as part of the instruction opcode. Operand 1
is an immediate value that serves as a source for the instruction.
Arithmetic instructions require two sources. Instructions using
this addressing mode are two bytes in length.
The result of an instruction using this addressing mode is placed
in either the A register or the X register, which is specified as part
of the instruction opcode. Operand 1 is added to the X register
forming an address that points to a location in either the RAM
memory space or the register space that is the source for the
instruction. Arithmetic instructions require two sources; the
second source is the A register or X register specified in the
opcode. Instructions using this addressing mode are two bytes
in length.
Table 14. Source Indexed
Opcode
Table 12. Source Immediate
Opcode
Operand 1
Instruction
Immediate Value
Examples
ADD A,
7 In this case, the immediate value of 7 is
added with the Accumulator, and the result
is placed in the Accumulator.
MOV
X,
8 In this case, the immediate value of 8 is
moved to the X register.
AND
F,
9 In this case, the immediate value of 9 is
logically ANDed with the F register and the
result is placed in the F register.
Source Direct
The result of an instruction using this addressing mode is placed
in either the A register or the X register, which is specified as part
of the instruction opcode. Operand 1 is an address that points to
a location in either the RAM memory space or the register space
that is the source for the instruction. Arithmetic instructions
require two sources; the second source is the A register or X
register specified in the opcode. Instructions using this
addressing mode are two bytes in length.
Opcode
Examples
ADD
A,
MOV
X,
Operand 1
Source Address
[7]
Source Index
Examples
ADD A,
MOV
X,
[X+7]
In this case, the value in the RAM
memory location at address 7 is
added with the Accumulator, and the
result is placed in the Accumulator.
REG[8] In this case, the value in the register
space at address 8 is moved to the X
register.
Document Number: 001-07611 Rev *I
In this case, the value in the memory
location at address X + 7 is added
with the Accumulator, and the result
is placed in the Accumulator.
REG[X+8] In this case, the value in the register
space at address X + 8 is moved to
the X register.
Destination Direct
The result of an instruction using this addressing mode is placed
within either the RAM memory space or the register space.
Operand 1 is an address that points to the location of the result.
The source for the instruction is either the A register or the X
register, which is specified as part of the instruction opcode.
Arithmetic instructions require two sources; the second source is
the location specified by Operand 1. Instructions using this
addressing mode are two bytes in length.
Table 15. Destination Direct
Opcode
Operand 1
Instruction
Table 13. Source Direct
Instruction
Operand 1
Instruction
Examples
ADD
[7],
MOV
REG[8],
Destination Address
A
In this case, the value in the memory
location at address 7 is added with
the Accumulator, and the result is
placed in the memory location at
address 7. The Accumulator is
unchanged.
A
In this case, the Accumulator is
moved to the register space location
at address 8. The Accumulator is
unchanged.
Page 16 of 72
CYRF69103
Destination Indexed
Destination Indexed Source Immediate
The result of an instruction using this addressing mode is placed
within either the RAM memory space or the register space.
Operand 1 is added to the X register forming the address that
points to the location of the result. The source for the instruction
is the A register. Arithmetic instructions require two sources; the
second source is the location specified by Operand 1 added with
the X register. Instructions using this addressing mode are two
bytes in length.
The result of an instruction using this addressing mode is placed
within either the RAM memory space or the register space.
Operand 1 is added to the X register to form the address of the
result. The source for the instruction is Operand 2, which is an
immediate value. Arithmetic instructions require two sources; the
second source is the location specified by Operand 1 added with
the X register. Instructions using this addressing mode are three
bytes in length.
Table 16. Destination Indexed
Table 18. Destination Indexed Source Immediate
Opcode
Operand 1
Instruction
Example
ADD
[X+7],
Destination Index
A
In this case, the value in the memory
location at address X+7 is added with
the Accumulator, and the result is
placed in the memory location at
address x+7. The Accumulator is
unchanged.
Opcode
Table 17. Destination Direct Source Immediate
Opcode
Instruction
Examples
ADD
[7],
MOV
REG[8],
Operand 1
Destination Address
Operand 2
Immediate Value
MOV
REG[X+8],
6
In this case, value in the memory
location at address 7 is added to the
immediate value of 5, and the result is
placed in the memory location at
address 7.
Operand 2
Immediate Value
5
In this case, the value in the
memory location at address X+7
is added with the immediate value
of 5 and the result is placed in the
memory location at address X+7.
6
In this case, the immediate value
of 6 is moved into the location in
the register space at address
X+8.
Destination Direct Source Direct
The result of an instruction using this addressing mode is placed
within the RAM memory. Operand 1 is the address of the result.
Operand 2 is an address that points to a location in the RAM
memory that is the source for the instruction. This addressing
mode is only valid on the MOV instruction. The instruction using
this addressing mode is three bytes in length.
Table 19. Destination Direct Source Direct
Opcode
Instruction
5
Destination Index
Examples
ADD
[X+7],
Destination Direct Source Immediate
The result of an instruction using this addressing mode is placed
within either the RAM memory space or the register space.
Operand 1 is the address of the result. The source for the
instruction is Operand 2, which is an immediate value. Arithmetic
instructions require two sources; the second source is the
location specified by Operand 1. Instructions using this
addressing mode are three bytes in length.
Operand 1
Instruction
Example
MOV [7],
Operand 1
Destination Address
Operand 2
Source Address
[8] In this case, the value in the memory
location at address 8 is moved to the
memory location at address 7.
In this case, the immediate value of 6
is moved into the register space
location at address 8.
Document Number: 001-07611 Rev *I
Page 17 of 72
CYRF69103
Source Indirect Post Increment
Destination Indirect Post Increment
The result of an instruction using this addressing mode is placed
in the Accumulator. Operand 1 is an address pointing to a
location within the memory space, which contains an address
(the indirect address) for the source of the instruction. The
indirect address is incremented as part of the instruction
execution. This addressing mode is only valid on the MVI
instruction. The instruction using this addressing mode is two
bytes in length. Refer to the PSoC Designer: Assembly
Language User Guide for further details on MVI instruction.
The result of an instruction using this addressing mode is placed
within the memory space. Operand 1 is an address pointing to a
location within the memory space, which contains an address
(the indirect address) for the destination of the instruction. The
indirect address is incremented as part of the instruction
execution. The source for the instruction is the Accumulator. This
addressing mode is only valid on the MVI instruction. The
instruction using this addressing mode is two bytes in length.
Table 20. Source Indirect Post Increment
Opcode
Instruction
Example
MVI
A,
Operand 1
Source Address Address
[8]
In this case, the value in the memory
location at address 8 is an indirect
address. The memory location pointed to
by the indirect address is moved into the
Accumulator. The indirect address is then
incremented.
Document Number: 001-07611 Rev *I
Table 21. Destination Indirect Post Increment
Opcode
Instruction
Example
MVI
[8],
Operand 1
Destination Address Address
A
In this case, the value in the memory
location at address 8 is an indirect
address. The Accumulator is moved
into the memory location pointed to by
the indirect address. The indirect
address is then incremented.
Page 18 of 72
CYRF69103
Instruction Set Summary
Cycles
Bytes
Opcode Hex
Cycles
Bytes
Opcode Hex
Cycles
Bytes
Opcode Hex
The instruction set is summarized in Table 22 numerically and serves as a quick reference. If more information is needed, the
Instruction Set Summary tables are described in detail in the PSoC Designer Assembly Language User Guide (available on
www.cypress.com).
Table 22. Instruction Set Summary Sorted Numerically by Opcode Order [1, 2]
00 15
1
SSC
2D
8
2
OR [X+expr], A
Z
5A
5
2
MOV [expr], X
01
4
2
ADD A, expr
C, Z
2E
9
3
OR [expr], expr
Z
5B
4
1
MOV A, X
02
6
2
ADD A, [expr]
C, Z
2F 10
3
OR [X+expr], expr
Z
5C
4
1
MOV X, A
03
7
2
ADD A, [X+expr]
C, Z
30
9
1
HALT
5D
6
2
MOV A, reg[expr]
Z
04
7
2
ADD [expr], A
C, Z
31
4
2
XOR A, expr
Z
5E
7
2
MOV A, reg[X+expr]
Z
05
8
2
ADD [X+expr], A
C, Z
32
6
2
XOR A, [expr]
Z
5F 10
3
MOV [expr], [expr]
06
Instruction Format
Flags
Instruction Format
Flags
Instruction Format
Flags
Z
9
3
ADD [expr], expr
C, Z
33
7
2
XOR A, [X+expr]
Z
60
5
2
MOV reg[expr], A
07 10
3
ADD [X+expr], expr
C, Z
34
7
2
XOR [expr], A
Z
61
6
2
MOV reg[X+expr], A
08
4
1
PUSH A
35
8
2
XOR [X+expr], A
Z
62
8
3
MOV reg[expr], expr
09
4
2
ADC A, expr
C, Z
36
9
3
XOR [expr], expr
Z
63
9
3
MOV reg[X+expr], expr
0A
6
2
ADC A, [expr]
C, Z
37 10
3
XOR [X+expr], expr
Z
64
4
1
ASL A
C, Z
0B
7
2
ADC A, [X+expr]
C, Z
38
5
2
ADD SP, expr
65
7
2
ASL [expr]
C, Z
0C
7
2
ADC [expr], A
C, Z
39
5
2
CMP A, expr
8
2
ASL [X+expr]
C, Z
0D
8
2
ADC [X+expr], A
C, Z
3A
7
2
CMP A, [expr]
if (A=B) Z=1 66
if (A<B) C=1
67
4
1
ASR A
C, Z
0E
9
3
ADC [expr], expr
C, Z
3B
8
2
CMP A, [X+expr]
68
7
2
ASR [expr]
C, Z
0F 10
3
ADC [X+expr], expr
C, Z
3C
8
3
CMP [expr], expr
69
8
2
ASR [X+expr]
C, Z
10
4
1
PUSH X
3D
9
3
CMP [X+expr], expr
6A
4
1
RLC A
C, Z
11
4
2
SUB A, expr
C, Z
3E 10
2
MVI A, [ [expr]++ ]
6B
7
2
RLC [expr]
C, Z
12
6
2
SUB A, [expr]
C, Z
3F 10
2
MVI [ [expr]++ ], A
6C
8
2
RLC [X+expr]
C, Z
13
7
2
SUB A, [X+expr]
C, Z
40
4
1
NOP
6D
4
1
RRC A
C, Z
14
7
2
SUB [expr], A
C, Z
41
9
3
AND reg[expr], expr
Z
6E
7
2
RRC [expr]
C, Z
15
8
2
SUB [X+expr], A
C, Z
42 10
3
AND reg[X+expr], expr
Z
6F
8
2
RRC [X+expr]
C, Z
16
9
3
SUB [expr], expr
C, Z
43
9
3
OR reg[expr], expr
Z
70
4
2
AND F, expr
C, Z
17 10
3
SUB [X+expr], expr
C, Z
44 10
3
OR reg[X+expr], expr
Z
71
4
2
OR F, expr
C, Z
18
5
1
POP A
45
9
3
XOR reg[expr], expr
Z
72
4
2
XOR F, expr
C, Z
19
4
2
SBB A, expr
C, Z
46 10
3
XOR reg[X+expr], expr
Z
73
4
1
CPL A
Z
1A
6
2
SBB A, [expr]
C, Z
47
8
3
TST [expr], expr
Z
74
4
1
INC A
C, Z
Z
Z
1B
7
2
SBB A, [X+expr]
C, Z
48
9
3
TST [X+expr], expr
Z
75
4
1
INC X
C, Z
1C
7
2
SBB [expr], A
C, Z
49
9
3
TST reg[expr], expr
Z
76
7
2
INC [expr]
C, Z
1D
8
2
SBB [X+expr], A
C, Z
4A 10
3
TST reg[X+expr], expr
Z
77
8
2
INC [X+expr]
C, Z
1E
9
3
SBB [expr], expr
C, Z
4B
5
1
SWAP A, X
Z
78
4
1
DEC A
C, Z
1F 10
3
SBB [X+expr], expr
C, Z
4C
7
2
SWAP A, [expr]
Z
79
4
1
DEC X
C, Z
20
5
1
POP X
4D
7
2
SWAP X, [expr]
7A
7
2
DEC [expr]
C, Z
21
4
2
AND A, expr
Z
4E
5
1
SWAP A, SP
7B
8
2
DEC [X+expr]
C, Z
22
6
2
AND A, [expr]
Z
4F
4
1
MOV X, SP
7C 13
3
LCALL
23
7
2
AND A, [X+expr]
Z
50
4
2
MOV A, expr
Z
7D
7
3
LJMP
24
7
2
AND [expr], A
Z
51
5
2
MOV A, [expr]
Z
7E 10
1
RETI
25
8
2
AND [X+expr], A
Z
52
6
2
MOV A, [X+expr]
Z
7F
8
1
RET
26
Z
9
3
AND [expr], expr
Z
53
5
2
MOV [expr], A
8x
5
2
JMP
27 10
3
AND [X+expr], expr
Z
54
6
2
MOV [X+expr], A
9x
11
2
CALL
28 11
1
ROMX
Z
55
8
3
MOV [expr], expr
Ax
5
2
JZ
29
4
2
OR A, expr
Z
56
9
3
MOV [X+expr], expr
Bx
5
2
JNZ
2A
6
2
OR A, [expr]
Z
57
4
2
MOV X, expr
Cx
5
2
JC
2B
7
2
OR A, [X+expr]
Z
58
6
2
MOV X, [expr]
Dx
5
2
JNC
2C
7
2
OR [expr], A
Z
59
7
2
MOV X, [X+expr]
Ex
7
2
JACC
Fx 13
2
INDEX
C, Z
Z
Notes
1. Interrupt routines take 13 cycles before execution resumes at interrupt vector table.
2. The number of cycles required by an instruction is increased by one for instructions that span 256-byte boundaries in the Flash memory space.
Document Number: 001-07611 Rev *I
Page 19 of 72
CYRF69103
Memory Organization
Flash Program Memory Organization
Figure 8. Program Memory Space with Interrupt Vector Table
after reset
16-bit PC
Address
0x0000
0x0004
0x0008
0x000C
0x0010
0x0014
0x0018
0x001C
0x0020
0x0024
0x0028
0x002C
0x0030
0x0034
0x0038
0x003C
0x0040
0x0044
0x0048
0x004C
0x0050
0x0054
0x0058
0x005C
0x0060
0x0064
0x0068
Program execution begins here after a reset
POR/LVD
Reserved
SPI Transmitter Empty
SPI Receiver Full
GPIO Port 0
GPIO Port 1
INT1
Reserved
Reserved
Reserved
Reserved
Reserved
1 ms Interval Timer
Programmable Interval Timer
Reserved
Reserved
16-bit Free Running Timer Wrap
INT2
Reserved
GPIO Port 2
Reserved
Reserved
Reserved
Reserved
Sleep Timer
Program Memory begins here (if below interrupts not used,
program memory can start lower)
0x1FFF
Document Number: 001-07611 Rev *I
Page 20 of 72
CYRF69103
Data Memory Organization
The MCU function provides up to 256 bytes of data RAM.
Figure 9. Data Memory Organization
after reset
Address
8-bit PSP
0x00
Top of RAM Memory
Stack begins here and grows upward
0xFF
Flash
SROM
This section describes the Flash block of the CYRF69103. Much
of the user visible Flash functionality, including programming and
security, are implemented in the M8C Supervisory Read Only
Memory (SROM). CYRF69103 Flash has an endurance of
1000 cycles and 10-year data retention.
The SROM holds code that is used to boot the part, calibrate
circuitry, and perform Flash operations (Table 23 lists the SROM
functions). The functions of the SROM may be accessed in
normal user code or operating from Flash. The SROM exists in
a separate memory space from user code. The SROM functions
are accessed by executing the Supervisory System Call
instruction (SSC), which has an opcode of 00h. Before executing
the SSC, the M8C’s accumulator needs to be loaded with the
desired SROM function code from Table 23. Undefined functions
causes a HALT if called from user code. The SROM functions
are executing code with calls; therefore, the functions require
stack space. With the exception of Reset, all of the SROM
functions have a parameter block in SRAM that must be
configured before executing the SSC. Table 24 on page 22 lists
all possible parameter block variables. The meaning of each
parameter, with regards to a specific SROM function, is
described later in this section.
Flash Programming and Security
All Flash programming is performed by code in the SROM. The
registers that control the Flash programming are only visible to
the M8C CPU when it is executing out of SROM. This makes it
impossible to read, write, or erase the Flash by bypassing the
security mechanisms implemented in the SROM.
Customer firmware can only program the Flash through SROM
calls. The data or code images can be sourced by way of any
interface with the appropriate support firmware. This type of
programming requires a ‘bootloader’ – a piece of firmware
resident on the Flash. For safety reasons, this bootloader must
not be over written during firmware rewrites.
The Flash provides four auxiliary rows that are used to hold Flash
block protection flags, boot time calibration values, configuration
tables, and any device values. The routines for accessing these
auxiliary rows are documented in the SROM section. The
auxiliary rows are not affected by the device erase function.
In-System Programming
CYRF69103 enables this type of in-system programming by
using the P1.0 and P1.1 pins as the serial programming mode
interface. This allows an external controller to cause the
CYRF69103 to enter serial programming mode and then to use
the test queue to issue Flash access functions in the SROM.
Document Number: 001-07611 Rev *I
Table 23. SROM Function Codes
Function Code
Function Name
Stack Space
00h
SWBootReset
0
01h
ReadBlock
7
02h
WriteBlock
10
03h
EraseBlock
9
05h
EraseAll
11
06h
TableRead
3
07h
CheckSum
3
Page 21 of 72
CYRF69103
Two important variables that are used for all functions are KEY1
and KEY2. These variables are used to help discriminate
between valid SSCs and inadvertent SSCs. KEY1 must always
have a value of 3Ah, while KEY2 must have the same value as
the stack pointer when the SROM function begins execution.
This is the Stack Pointer value when the SSC opcode is
executed, plus three. If either of the keys do not match the
expected values, the M8C halts (with the exception of the
SWBootReset function). The following code puts the correct
value in KEY1 and KEY2. The code starts with a halt, to force the
program to jump directly into the setup code and not run into it.
halt
SSCOP: mov [KEY1], 3ah
mov X, SP
mov A, X
add A, 3
mov [KEY2], A
Table 24. SROM Function Parameters
Variable Name
Key1/Counter/Return Code
Key2/TMP
BlockID
Pointer
Clock
Mode
Delay
PCL
SRAM Address
0,F8h
0,F9h
0,FAh
0,FBh
0,FCh
0,FDh
0,FEh
0,FFh
The SROM also features Return Codes and Lockouts.
Return Codes
Return codes aid in the determination of success or failure of a
particular function. The return code is stored in KEY1’s position
in the parameter block. The CheckSum and TableRead functions
do not have return codes because KEY1’s position in the
parameter block is used to return other data.
Table 25. SROM Return Codes
Return Code
Description
00h
Success
01h
Function not allowed due to level of protection
on block
02h
Software reset without hardware reset
03h
Fatal error, SROM halted
Read, write, and erase operations may fail if the target block is
read or write protected. Block protection levels are set during
device programming.
The EraseAll function overwrites data in addition to leaving the
entire user Flash in the erase state. The EraseAll function loops
through the number of Flash macros in the product, executing
the following sequence: erase, bulk program all zeros, erase.
After all the user space in all the Flash macros are erased, a
second loop erases and then programs each protection block
with zeros.
Document Number: 001-07611 Rev *I
SROM Function Descriptions
All SROM functions are described in the following sections.
SWBootReset Function
The SROM function, SWBootReset, is the function that is
responsible for transitioning the device from a reset state to
running user code. The SWBootReset function is executed
whenever the SROM is entered with an M8C accumulator value
of 00h; the SRAM parameter block is not used as an input to the
function. This happens, by design, after a hardware reset,
because the M8C's accumulator is reset to 00h or when user
code executes the SSC instruction with an accumulator value of
00h. The SWBootReset function does not execute when the
SSC instruction is executed with a bad key value and a nonzero
function code. A CYRF69103 device executes the HALT
instruction if a bad value is given for either KEY1 or KEY2.
The SWBootReset function verifies the integrity of the calibration
data by way of a 16-bit checksum, before releasing the M8C to
run user code.
ReadBlock Function
The ReadBlock function is used to read 64 contiguous bytes
from Flash – a block.
The first thing this function does is to check the protection bits
and determine if the desired BLOCKID is readable. If read
protection is turned on, the ReadBlock function exits setting the
accumulator and KEY2 back to 00h. KEY1 has a value of 01h,
indicating a read failure. If read protection is not enabled, the
function reads 64 bytes from the Flash using a ROMX instruction
and store the results in SRAM using an MVI instruction. The first
of the 64 bytes are stored in SRAM at the address indicated by
the value of the POINTER parameter. When the ReadBlock
completes successfully, the accumulator, KEY1 and KEY2, all
have a value of 00h.
Table 26. ReadBlock Parameters
Name
Address
Description
KEY1
0,F8h
3Ah
KEY2
0,F9h
Stack Pointer value, when SSC is
executed
BLOCKID
0,FAh
Flash block number
POINTER
0,FBh
First of 64 addresses in SRAM
where returned data must be stored
WriteBlock Function
The WriteBlock function is used to store data in the Flash. Data
is moved 64 bytes at a time from SRAM to Flash using this
function. The first thing the WriteBlock function does is to check
the protection bits and determine if the desired BLOCKID is
writable. If write protection is turned on, the WriteBlock function
exits, setting the accumulator and KEY2 back to 00h. KEY1 has
a value of 01h, indicating a write failure. The configuration of the
WriteBlock function is straightforward. The BLOCKID of the
Flash block, where the data is stored, must be determined and
stored at SRAM address FAh.
The SRAM address of the first of the 64 bytes to be stored in
Flash must be indicated using the POINTER variable in the
Page 22 of 72
CYRF69103
parameter block (SRAM address FBh). Finally, the CLOCK and
DELAY values must be set correctly. The CLOCK value
determines the length of the write pulse that is used to store the
data in the Flash. The CLOCK and DELAY values are dependent
on the CPU. Refer to ‘Clocking’ Section for additional
information.
Table 27. WriteBlock Parameters
Name
Address
Description
KEY1
0,F8h
3Ah
KEY2
0,F9h
Stack Pointer value, when SSC is
executing
BLOCK ID
0,FAh
8 KB Flash block number (00h–7Fh)
4 KB Flash block number (00h–3Fh)
3 KB Flash block number (00h–2Fh)
POINTER
0,FBh
First 64 addresses in SRAM where
the data to be stored in Flash is
located before calling WriteBlock
CLOCK
0,FCh
Clock Divider used to set the write
Pulse width
DELAY
0,FEh
For a CPU speed of 12 MHz set to 56h
available. In the table, ER and EW are used to indicate the ability
to perform external reads and writes. For internal writes, IW is
used. Internal reading is always permitted by way of the ROMX
instruction. The ability to read by way of the SROM ReadBlock
function is indicated by SR. The protection level is stored in two
bits, according to Table 29. These bits are bit packed into the 64
bytes of the protection block. Therefore, each protection block
byte stores the protection level for four Flash blocks. The bits are
packed into a byte, with the lowest numbered block’s protection
level stored in the lowest numbered bits.
The first address of the protection block contains the protection
level for blocks 0 through 3; the second address is for blocks 4
through 7. The 64th byte stores the protection level for blocks
252 through 255.
Table 29. Protection Modes
Mode
00b
Settings
Description
Marketing
SR ER EW IW Unprotected
Unprotected
Factory upgrade
01b
SR ER EW IW Read protect
10b
SR ER EW IW Disable external Field upgrade
write
11b
SR ER EW IW Disable internal
write
Full protection
EraseBlock Function
The EraseBlock function is used to erase a block of 64
contiguous bytes in Flash. The first thing the EraseBlock function
does is to check the protection bits and determine if the desired
BLOCKID is writable. If write protection is turned on, the
EraseBlock function exits, setting the accumulator and KEY2
back to 00h. KEY1 has a value of 01h, indicating a write failure.
The EraseBlock function is only useful as the first step in
programming. Erasing a block does not cause data in a block to
be one hundred percent unreadable. If the objective is to
obliterate data in a block, the best method is to perform an
EraseBlock followed by a WriteBlock of all zeros.
7
6
Block n+3
5
4
Block n+2
3
2
Block n+1
1
0
Block n
To set up the parameter block for the EraseBlock function,
correct key values must be stored in KEY1 and KEY2. The block
number to be erased must be stored in the BLOCKID variable
and the CLOCK and DELAY values must be set based on the
current CPU speed.
The level of protection is only decreased by an EraseAll, which
places zeros in all locations of the protection block. To set the
level of protection, the ProtectBlock function is used. This
function takes data from SRAM, starting at address 80h, and
ORs it with the current values in the protection block. The result
of the OR operation is then stored in the protection block. The
EraseBlock function does not change the protection level for a
block. Because the SRAM location for the protection data is fixed
and there is only one protection block per Flash macro, the
ProtectBlock function expects very few variables in the
parameter block to be set before calling the function. The
parameter block values that must be set, besides the keys, are
the CLOCK and DELAY values.
Table 28. EraseBlock Parameters
Table 30. ProtectBlock Parameters
Name
Address
Description
Name
Address
Description
KEY1
0,F8h
3Ah
KEY1
0,F8h
3Ah
KEY2
0,F9h
Stack Pointer value when SSC is
executed
KEY2
0,F9h
Stack Pointer value when SSC is
executed
BLOCKID
0,FAh
Flash block number (00h–7Fh)
CLOCK
0,FCh
CLOCK
0,FCh
Clock Divider used to set the erase
pulse width
Clock Divider used to set the write
pulse width
DELAY
0,FEh
For a CPU speed of 12 MHz set to 56h
DELAY
0,FEh
For a CPU speed of 12 MHz set to
56h
ProtectBlock Function
The CYRF69103 device offers Flash protection on a
block-by-block basis. Table 29 lists the protection modes
Document Number: 001-07611 Rev *I
EraseAll Function
The EraseAll function performs a series of steps that destroy the
user data in the Flash macros and resets the protection block in
each Flash macro to all zeros (the unprotected state). The
EraseAll function does not affect the three hidden blocks above
Page 23 of 72
CYRF69103
the protection block in each Flash macro. The first of these four
hidden blocks is used to store the protection table for its eight
Kbytes of user data.
The EraseAll function begins by erasing the user space of the
Flash macro with the highest address range. A bulk program
of all zeros is then performed on the same Flash macro, to
destroy all traces of the previous contents. The bulk program
is followed by a second erase that leaves the Flash macro in
a state ready for writing. The erase, program, erase sequence
is then performed on the next lowest Flash macro in the
address space if it exists. Following the erase of the user
space, the protection block for the Flash macro with the
highest address range is erased. Following the erase of the
protection block, zeros are written into every bit of the
protection table. The next lowest Flash macro in the address
space then has its protection block erased and filled with
zeros.
The end result of the EraseAll function is that all user data in
the Flash is destroyed and the Flash is left in an unprogrammed state, ready to accept one of the various write
commands. The protection bits for all user data are also reset
to the zero state.
The parameter block values that must be set, besides the
keys, are the CLOCK and DELAY values.
Table 31. EraseAll Parameters
Name
Address
Description
numbered zero through seven. All user and hidden blocks in
the CYRF69103 consist of 64 bytes.
An internal table holds the Silicon ID and returns the Revision
ID. The Silicon ID is returned in SRAM, while the Revision ID
is returned in the CPU_A and CPU_X registers. The Silicon ID
is a value placed in the table by programming the Flash and is
controlled by Cypress Semiconductor Product Engineering.
The Revision ID is hard coded into the SROM. The Revision
ID is discussed in more detail later in this section.
An internal table holds alternate trim values for the device and
returns a one-byte internal revision counter. The internal
revision counter starts out with a value of zero and is incremented each time one of the other revision numbers is not
incremented. It is reset to zero each time one of the other
revision numbers is incremented. The internal revision count
is returned in the CPU_A register. The CPU_X register is
always set to FFh when trim values are read. The BLOCKID
value, in the parameter block, is used to indicate which table
must be returned to the user. Only the three least significant
bits of the BLOCKID parameter are used by the TableRead
function for the CYRF69103. The upper five bits are ignored.
When the function is called, it transfers bytes from the table to
SRAM addresses F8h–FFh.
The M8C’s A and X registers are used by the TableRead
function to return the die’s Revision ID. The Revision ID is a
16-bit value hard coded into the SROM that uniquely identifies
the die’s design.
KEY1
0,F8h
3Ah
Checksum Function
KEY2
0,F9h
Stack Pointer value when SSC is
executed
CLOCK
0,FCh
Clock Divider used to set the write pulse
width
DELAY
0,FEh
For a CPU speed of 12 MHz set to 56h
The Checksum function calculates a 16-bit checksum over a
user specifiable number of blocks, within a single Flash macro
(Bank) starting from block zero. The BLOCKID parameter is
used to pass in the number of blocks to calculate the
checksum over. A BLOCKID value of 1 calculates the
checksum of only block 0, while a BLOCKID value of 0 calculates the checksum of all 256 user blocks. The 16-bit
checksum is returned in KEY1 and KEY2. The parameter
KEY1 holds the lower eight bits of the checksum and the
parameter KEY2 holds the upper eight bits of the checksum.
TableRead Function
The TableRead function gives the user access to part specific
data stored in the Flash during manufacturing. It also returns
a Revision ID for the die (not to be confused with the Silicon
ID).
Table 32. Table Read Parameters
Name
Address
Description
KEY1
0,F8h
3Ah
KEY2
0,F9h
Stack Pointer value when SSC is
executed
BLOCKID 0,FAh
Table number to read
The table space for the CYRF69103 is simply a 64 byte row
broken up into eight tables of eight bytes. The tables are
Document Number: 001-07611 Rev *I
The checksum algorithm executes the following sequence of
three instructions over the number of blocks times 64 to be
checksummed.
romx
add [KEY1], A
adc [KEY2], 0
Table 33. Checksum Parameters
Name
Address
Description
KEY1
0,F8h
3Ah
KEY2
0,F9h
Stack Pointer value when SSC is
executed
BLOCKID
0,FAh
Number of Flash blocks to calculate
checksum on
Page 24 of 72
CYRF69103
Clocking
also be used as a clocking source for the Interval Timer clock
(ITMRCLK) and Capture Timer clock (TCAPCLK). The 32 kHz
Low power Oscillator can operate in low power mode or can
provide a more accurate clock in normal mode. The Internal 32
kHz Low power Oscillator accuracy ranges from –53.12% to
+56.25%. The 32 kHz low power oscillator can be calibrated
against the internal 24 MHz oscillator or another timing source if
desired.
The CYRF69103 internal oscillator outputs two frequencies, the
Internal 24 MHz Oscillator and the 32 kHz Low power Oscillator.
The Internal 24 MHz Oscillator is designed such that it may be
trimmed to an output frequency of 24 MHz over temperature and
voltage variation. The Internal 24 MHz Oscillator accuracy is 24
MHz –22% to +10% (between 0 °C–70 °C). No external components are required to achieve this level of accuracy.
CYRF69103 provides the ability to load new trim values for the
24 MHz oscillator based on voltage. This allows Vdd to be
monitored and have firmware trim the oscillator based on voltage
present. The IOSCTR register is used to set trim values for the
24 MHz oscillator. CYRF69103 is initialized with 3.30V trim
values at power on, then firmware is responsible for transferring
the correct set of trim values to the trim registers to match the
application’s actual Vdd. The 32 kHz oscillator generally does
not require trim adjustments versus voltage but trim values for
the 32 kHz are also stored in Supervisory ROM.
Firmware is responsible for selecting the correct trim values from
the User row to match the power supply voltage in the end application and writing the values to the trim registers IOSCTR and
LPOSCTR.
The internal low speed oscillator of nominally 32 kHz provides a
slow clock source for the CYRF69103 in suspend mode. This is
used to generate a periodic wakeup interrupt and provide a clock
to sequential logic during power up and power down events
when the main clock is stopped. In addition, this oscillator can
Figure 10. SROM Table
F8h
Table 0
Silicon ID
[15-8]
F9h
FAh
FBh
FCh
FDh
FEh
FFh
Silicon ID
[7-0]
lid ing
Va rat n
pe io
O Reg
Table 1
24 MHz
IOSCTR
at 3.30V
Table 2
32 kHz
32 kHz
32 kHz
32 kHz
at 3.30V
at 3.00V
at 2.85V
at 2.70V
24 MHz
IOSCTR
at 3.00V
24 MHz
IOSCTR
at 2.85V
24 MHz
IOSCTR
at 2.70V
Table 3 LPOSCTR LPOSCTR LPOSCTR LPOSCTR
Table 4
Table 5
Table 6
Table 7
To improve the accuracy of the IMO, new trim values are loaded based on supply voltage to the part. For this, firmware needs to make
modifications to two registers:
1. The internal oscillator trim register at location 0x34.
2. The gain register at location 0x38.
Document Number: 001-07611 Rev *I
Page 25 of 72
CYRF69103
Trim values for the IOSCTR register:
The trim values are stored in SROM tables in the part as shown in Figure 10 on page 25.
The trim values are read out from the part based on voltage settings and written to the IOSCTR register at location 0x34. The following
pseudo code shows how this is done.
_main:
mov
A, 2
mov
[SSC_BLOCKID], A
Call SROM operation to read the SROM table (Refer to section SROM Table Read Description)
//After this command is executed, the trim values for 3.3, 3.0, 2.85 and 2.7 are stored at locations
FC through FF in the RAM. SROM calls are explained in the previous section of this datasheet
;
mov
A, [FCh]
// trim values for 3.3V
mov
A, [FDh]
// trim values for 3.0V
;
mov
A, [FEh]
// trim values for 2.85V
;
mov
A, [FFh]
// trim values for 2.70V
mov
reg[IOSCTR],A // Loading IOSCTR with trim values for 3.0V
.terminate:
jmp .terminate
SROM Table Read Description
The Silicon IDs for CYRF69103 devices are stored in SROM tables in the part, as shown in Figure 10 on page 25.
The Silicon ID can be read out from the part using SROM Table reads. This is demonstrated in the following pseudo code. As
mentioned in the section SROM on page 21, the SROM variables occupy address F8h through FFh in the SRAM. Each of the variables
and their definition in given in the section SROM on page 21.
AREA SSCParmBlkA(RAM,ABS)
org
F8h // Variables are defined starting at address F8h
SSC_KEY1:
SSC_RETURNCODE:
blk 1
SSC_KEY2 :
blk 1
SSC_BLOCKID:
blk 1
SSC_POINTER:
blk 1
SSC_CLOCK:
blk 1
SSC_MODE:
blk 1
SSC_DELAY:
blk 1
SSC_WRITE_ResultCode: blk
; F8h supervisory key
; F8h result code
;F9h supervisory stack ptr key
; FAh block ID
; FBh pointer to data buffer
; FCh Clock
; FDh ClockW ClockE multiplier
; FEh flash macro sequence delay count
1 ; FFh temporary result code
_main:
mov
A, 0
mov
[SSC_BLOCKID], A// To read from Table 0 - Silicon ID is stored in Table 0
//Call SROM operation to read the SROM table
mov
X, SP
; copy SP into X
mov
A, X
; A temp stored in X
add
A, 3
; create 3 byte stack frame (2 + pushed A)
mov
[SSC_KEY2], A
; save stack frame for supervisory code
; load the supervisory code for flash operations
mov
[SSC_KEY1], 3Ah ;FLASH_OPER_KEY - 3Ah
mov
23 on page 21
SSC
A,6
; load A with specific operation. 06h is the code for Table read Table
; SSC call the supervisory ROM
// At the end of the SSC command the silicon ID is stored in F8 (MSB) and F9(LSB) of the SRAM
.terminate:
jmp .terminate
Document Number: 001-07611 Rev *I
Page 26 of 72
CYRF69103
Gain value for the register at location [0x38]:
3.3 V = 0x40
3.0 V = 0x40
2.85 V = 0xFF
2.70 V = 0xFF
Load register [0x38] with the gain values corresponding to the
appropriate voltage.
Table 34. Oscillator Trim Values vs. Voltage Settings
Supervisory ROM Table
Table2 FCh
Function
24 MHz IOSCTR at 3.30 V
Table2 FDh
24 MHz IOSCTR at 3.00 V
Table2 FEh
24 MHz IOSCTR at 2.85 V
Table2 FFh
24 MHz IOSCTR at 2.70 V
Table3 F8h
32 kHz LPOSCTR at 3.30 V
Table3 F9h
32 kHz LPOSCTR at 3.00 V
Table3 FAh
32 kHz LPOSCTR at 2.85 V
Table3 FBh
32 kHz LPOSCTR at 2.70 V
mov A, reg[PITMRL]
mov [58h],A
mov [59h], A
mov A, reg[PITMRL]
mov [60h], A
;;;Start comparison
mov A,[60h]
mov X, [59h]
sub A, [59h]
jz done
mov A, [59h]
mov X, [58h]
sub A, [58h]
jz done
mov X, [57h]
;;;correct data is in memory location 57h
done:
mov [57h], X
ret
Clock Architecture Description
The CYRF69103 clock selection circuitry allows the selection of
independent clocks for the CPU, Interval Timers, and Capture
Timers.
When using the 32 kHz oscillator the PITMRL/H must be read
until two consecutive readings match before sending/receiving
data. The following firmware example assumes the developer is
interested in the lower byte of the PIT.
Read_PIT_counter:
mov A, reg[PITMRL]
mov [57h], A
CPU Clock
The CPU clock, CPUCLK, can be sourced from the Internal
24 MHz oscillator. The selected clock source can optionally be
divided by 2n-1 where n is 0–7 (see Table 36 on page 28).
Table 35. CPU Clock Config (CPUCLKCR) [0x30] [R/W]
Bit #
7
6
5
4
3
2
1
0
Read/Write
–
–
–
–
–
–
–
–
Default
0
0
0
0
0
0
0
0
Field
Reserved
Bits 7:0
Reserved
Note The CPU speed selection is configured using the OSC_CR0 Register (Figure 11 on page 30).
Document Number: 001-07611 Rev *I
Page 27 of 72
CYRF69103
Table 36. OSC Control 0 (OSC_CR0) [0x1E0] [R/W]
Bit #
7
Field
6
5
Reserved
No Buzz
4
3
2
Sleep Timer [1:0]
1
0
CPU Speed [2:0]
Read/Write
–
–
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
1
0
0
0
Bits 7:6
Bit 5
Reserved
No Buzz
During sleep (the Sleep bit is set in the CPU_SCR Register—Table 40 on page 32), the LVD and POR detection
circuit is turned on periodically to detect any POR and LVD events on the VCC pin (the Sleep Duty Cycle bits in
the ECO_TR are used to control the duty cycle—Table 44 on page 37). To facilitate the detection of POR and
LVD events, the No Buzz bit is used to force the LVD and POR detection circuit to be continuously enabled during sleep. This results in a faster response to an LVD or POR event during sleep at the expense of a slightly
higher than average sleep current. Obtaining the absolute lowest power usage in sleep mode requires the No
Buzz bit be clear
0 = The LVD and POR detection circuit is turned on periodically as configured in the Sleep Duty Cycle.
1 = The Sleep Duty Cycle value is overridden. The LVD and POR detection circuit is always enabled.
Note The periodic Sleep Duty Cycle enabling is independent with the sleep interval shown in the following Sleep [1:0] bits.
Bits 4:3
Sleep Timer [1:0]
Sleep Timer Sleep Timer Clock
[1:0]
Frequency (Nominal)
Sleep Period
(Nominal)
Watchdog Period
(Nominal)
6 ms
00
512 Hz
1.95 ms
01
64 Hz
15.6 ms
47 ms
10
8 Hz
125 ms
375 ms
11
1 Hz
1 sec
3 sec
Note Sleep intervals are approximate
Bits 2:0
CPU Speed [2:0]
The CYRF69103 may operate over a range of CPU clock speeds. The reset value for the CPU Speed bits is
zero. Therefore, the default CPU speed is 3 MHz.
CPU Speed
[2:0]
CPU when Internal
Oscillator is selected
000
3 MHz (Default)
001
6 MHz
010
12 MHz
011
Reserved
100
1.5 MHz
101
750 kHz
110
187 kHz
111
Reserved
Document Number: 001-07611 Rev *I
Page 28 of 72
CYRF69103
Table 37. Timer Clock Config (TMRCLKCR) [0x31] [R/W]
Bit #
7
6
5
4
3
2
1
0
Field
TCAPCLK Divider
TCAPCLK Select
ITMRCLK Divider
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
1
0
0
0
1
1
1
1
Default
ITMRCLK Select
Bits 7:6
TCAPCLK Divider [1:0]
TCAPCLK Divider controls the TCAPCLK divisor.
0 0 = Divider Value 2
0 1 = Divider Value 4
1 0 = Divider Value 6
1 1 = Divider Value 8
Bits 5:4
TCAPCLK Select
The TCAPCLK Select field controls the source of the TCAPCLK.
0 0 = Internal 24 MHz Oscillator
0 1 =Reserved
1 0 = Internal 32 kHz Low power Oscillator
1 1 = TCAPCLK Disabled
Note The 1024 s interval timer is based on the assumption that TCAPCLK is running at 4 MHz. Changes in TCAPCLK
frequency cause a corresponding change in the 1024 s interval timer frequency.
Bits 3:2
ITMRCLK Divider
ITMRCLK Divider controls the ITMRCLK divisor
0 0 = Divider value of 1
0 1 = Divider value of 2
1 0 = Divider value of 3
1 1 = Divider value of 4
Bits 1:0
ITMRCLK Select
0 0 = Internal 24 MHz Oscillator
0 1 = Reserved
1 0 = Internal 32 kHz Low power Oscillator
1 1 = TCAPCLK
Note Changing the source of TMRCLK requires that both the source and destination clocks be running. Attempting to change
the clock source away from TCAPCLK after that clock has been stopped is not successful.
Interval Timer Clock (ITMRCLK)
The Interval Timer clock (ITMRCLK) can be sourced from the
internal 24 MHz oscillator, internal 32 kHz low power oscillator,
or timer capture clock. A programmable prescaler of 1, 2, 3, or 4
then divides the selected source. The 12-bit Programmable
Interval Timer is a simple down counter with a programmable
reload value. It provides a 1 s resolution by default. When the
down counter reaches zero, the next clock is spent reloading.
The reload value can be read and written while the counter is
running, but care must be taken to ensure that the counter does
not unintentionally reload while the 12-bit reload value is only
partially stored – for example, between the two writes of the
12-bit value. The programmable interval timer generates
interrupt to the CPU on each reload.
The parameters to be set appears on the device editor view of
PSoC Designer after you place the CYRF69103 timer user
module. The parameters are PITIMER_Source and
PITIMER_Divider. The PITIMER_Source is the clock to the timer
and the PITIMER_Divider is the value the clock is divided by.
Document Number: 001-07611 Rev *I
The interval register (PITMR) holds the value that is loaded into
the PIT counter on terminal count. The PIT counter is a down
counter.
The Programmable Interval Timer resolution is configurable. For
example:
TCAPCLK divide by x of CPU clock (for example TCAPCLK
divide by 2 of a 24 MHz CPU clock gives a frequency of 12 MHz)
ITMRCLK divide by x of TCAPCLK (for example, ITMRCLK
divide by 3 of TCAPCLK is 4 MHz so resolution is 0.25 s).
Timer Capture Clock (TCAPCLK)
The Timer Capture clock (TCAPCLK) can be sourced from the
internal 24 MHz oscillator or the internal 32 kHz low power
oscillator. A programmable prescaler of 2, 4, 6, or 8 then divides
the selected source.
Page 29 of 72
CYRF69103
Figure 11. Programmable Interval Timer Block Diagram
C o n fig u ra tio n
S ta tu s a n d
C o n tro l
S y s te m
C lo c k
1 2 -b it
re lo a d
v a lu e
1 2 -b it d o w n
c o u n te r
C lo c k
T im e r
1 2 -b it
re lo a d
c o u n te r
In te rru p t
C o n tro lle r
Internal Clock Trim
Table 38. IOSC Trim (IOSCTR) [0x34] [R/W]
Bit #
7
Field
Read/Write
Default
6
5
4
3
foffset[2:0]
2
1
0
Gain[4:0]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
D
D
D
D
D
The IOSC Calibrate register is used to calibrate the internal oscillator. The reset value is undefined but during boot the SROM
writes a calibration value that is determined during manufacturing test. The ‘D’ indicates that the default value is trimmed to
24 MHz at 3.30V at power on.
Bits 7:5
foffset [2:0]
This value is used to trim the frequency of the internal oscillator. These bits are not used in factory calibration
and are zero. Setting each of these bits causes the appropriate fine offset in oscillator frequency:
foffset bit 0 = 7.5 kHz
foffset bit 1 = 15 kHz
foffset bit 2 = 30 kHz
Bits 4:0
Gain [4:0]
The effective frequency change of the offset input is controlled through the gain input. A lower value of the gain
setting increases the gain of the offset input. This value sets the size of each offset step for the internal oscillator. Nominal gain change (kHz/offsetStep) at each bit, typical conditions (24 MHz operation):
Gain bit 0 = –1.5 kHz
Gain bit 1 = –3.0 kHz
Gain bit 2 = –6 kHz
Gain bit 4 = –24 kHz
Document Number: 001-07611 Rev *I
Page 30 of 72
CYRF69103
LPOSC Trim
Table 39. LPOSC Trim (LPOSCTR) [0x36] [R/W]
Bit #
7
6
Field
32 kHz Low
Power
Reserved
R/W
–
R/W
R/W
R/W
R/W
R/W
R/W
0
–
D
D
D
D
D
D
Read/Write
Default
5
4
3
32 kHz Bias Trim [1:0]
2
1
0
32 kHz Freq Trim [3:0]
This register is used to calibrate the 32 kHz Low speed Oscillator. The reset value is undefined but during boot the SROM
writes a calibration value that is determined during manufacturing test. This is the meaning of ‘D’ in the Default field. The trim
value can be adjusted vs. voltage as noted in Table 35 on page 27.
Bit 7
32 kHz Low Power
0 = The 32 kHz Low speed Oscillator operates in normal mode.
1 = The 32 kHz Low speed Oscillator operates in a low power mode. The oscillator continues to function normally but with reduced accuracy.
Bit 6
Reserved
Bits [5:4] 32 kHz Bias Trim [1:0]
These bits control the bias current of the low power oscillator.
0 0 = Mid bias
0 1 = High bias
1 0 = Reserved
1 1 = Reserved
Important Note Do not program the 32 kHz Bias Trim [1:0] field with the reserved 10b value as the oscillator does not oscillate
at all corner conditions with this setting.
Bits 3:0
32 kHz Freq Trim [3:0]
These bits are used to trim the frequency of the low power oscillator.
CPU Clock During Sleep Mode
When the CPU enters sleep mode, the oscillator is stopped. When the CPU comes out of sleep mode it is running on the internal
oscillator. The internal oscillator recovery time is three clock cycles of the Internal 32 kHz Low power Oscillator.
Document Number: 001-07611 Rev *I
Page 31 of 72
CYRF69103
Reset
The microcontroller supports two types of resets: Power on Reset (POR) and Watchdog Reset (WDR). When reset is initiated, all
registers are restored to their default states and all interrupts are disabled.
The occurrence of a reset is recorded in the System Status and Control Register (CPU_SCR). Bits within this register record the
occurrence of POR and WDR Reset respectively. The firmware can interrogate these bits to determine the cause of a reset.
The microcontroller resumes execution from Flash address 0x0000 after a reset. The internal clocking mode is active after a reset,
until changed by user firmware.
Note The CPU clock defaults to 3 MHz (Internal 24 MHz Oscillator divide-by-8 mode) at POR to guarantee operation at the low VCC
that might be present during the supply ramp.
Table 40. System Status and Control Register (CPU_SCR) [0xFF] [R/W]
Bit #
7
6
5
4
3
2
1
0
Field
GIES
Reserved
WDRS
PORS
Sleep
Reserved
Reserved
Stop
Read/Write
R
–
R/C[3]
R/C[3]
R/W
–
–
R/W
Default
0
0
0
1
0
1
0
0
The bits of the CPU_SCR register are used to convey status and control of events for various functions of a CYRF69103
device.
Bit 7
GIES
The Global Interrupt Enable Status bit is a read-only status bit and its use is discouraged. The GIES bit is a
legacy bit, which was used to provide the ability to read the GIE bit of the CPU_F register. However, the CPU_F
register is now readable. When this bit is set, it indicates that the GIE bit in the CPU_F register is also set which,
in turn, indicates that the microprocessor services interrupts:
0 = Global interrupts disabled
1 = Global interrupt enabled
Bit 6
Reserved
Bit 5
WDRS
The WDRS bit is set by the CPU to indicate that a WDR event has occurred. The user can read this bit to
determine the type of reset that has occurred. The user can clear but not set this bit:
0 = No WDR
1 = A WDR event has occurred
Bit 4
PORS
The PORS bit is set by the CPU to indicate that a POR event has occurred. The user can read this bit to
determine the type of reset that has occurred. The user can clear but not set this bit:
0 = No POR
1 = A POR event has occurred (Note that WDR events do not occur until this bit is cleared).
Bit 3
SLEEP
Set by the user to enable CPU sleep state. CPU remains in sleep mode until any interrupt is pending. The Sleep
bit is covered in more detail in the section Sleep Mode on page 33.
0 = Normal operation
1 = Sleep
Bits 2:1
Reserved
Bit 0
STOP
This bit is set by the user to halt the CPU. The CPU remains halted until a reset (WDR, POR, or external reset)
has taken place. If an application wants to stop code execution until a reset, the preferred method is to use the
HALT instruction rather than writing to this bit.
0 = Normal CPU operation
1 = CPU is halted (not recommended)
Note
3. C = Clear. This bit can only be cleared by the user and cannot be set by firmware.
Document Number: 001-07611 Rev *I
Page 32 of 72
CYRF69103
Power On Reset
POR occurs every time the power to the device is switched on.
POR is released when the supply is typically 2.6 V for the upward
supply transition, with typically 50 mV of hysteresis during the
power on transient. Bit 4 of the System Status and Control
Register (CPU_SCR) is set to record this event (the register
contents are set to 00010000 by the POR). After a POR, the
microprocessor is held off for approximately 20 ms for the VCC
supply to stabilize before executing the first instruction at
address 0x00 in the Flash. If the VCC voltage drops below the
POR downward supply trip point, POR is reasserted. The VCC
supply needs to ramp linearly from 0 to VCC in 0 to 200 ms.
Important The PORS status bit is set at POR and can only be
cleared by the user, and cannot be set by firmware.
Watchdog Timer Reset
The user has the option to enable the WDT. The WDT is enabled
by clearing the PORS bit. When the PORS bit is cleared, the
WDT cannot be disabled. The only exception to this is if a POR
event takes place, which disables the WDT.
The sleep timer is used to generate the sleep time period and the
Watchdog time period. The sleep timer uses the Internal 32 kHz
Low power Oscillator system clock to produce the sleep time
period. The user can program the sleep time period using the
Sleep Timer bits of the OSC_CR0 Register (Table 36 on page
28). When the sleep time elapses (sleep timer overflows), an
interrupt to the Sleep Timer Interrupt Vector is generated.
The Watchdog Timer period is automatically set to be three
counts of the Sleep Timer overflows. This represents between
two and three sleep intervals depending on the count in the
Sleep Timer at the previous WDT clear. When this timer reaches
three, a WDR is generated.
The user can either clear the WDT, or the WDT and the Sleep
Timer. Whenever the user writes to the Reset WDT Register
(RES_WDT), the WDT is cleared. If the data that is written is the
hex value 0x38, the Sleep Timer is also cleared at the same time.
Table 41. Reset Watchdog Timer (RESWDT) [0xE3] [W]
Bit #
7
6
5
4
3
2
Field
Reset Watchdog Timer [7:0]
Read/Write
W
W
W
W
W
W
Default
0
0
0
0
0
0
Any write to this register clears the Watchdog Timer, a write of 0x38 also clears the Sleep Timer.
Bits 7:0
Reset Watchdog Timer [7:0]
Sleep Mode
The CPU can only be put to sleep by the firmware. This is
accomplished by setting the Sleep bit in the System Status and
Control Register (CPU_SCR). This stops the CPU from
executing instructions, and the CPU remains asleep until an
interrupt comes pending, or there is a reset event (either a Power
on Reset, or a Watchdog Timer Reset).
The Low voltage Detection circuit (LVD) drops into fully functional
power reduced states, and the latency for the LVD is increased.
The actual latency can be traded against power consumption by
changing the Sleep Duty Cycle field of the ECO_TR Register.
The Internal 32 kHz low speed oscillator remains running. Before
entering suspend mode, firmware can optionally configure the
32 kHz Low speed Oscillator to operate in a low power mode to
help reduce the overall power consumption (using the 32 kHz
Low Power bit, Table 39). This helps save approximately 5 A;
however, the trade off is that the 32 kHz Low speed Oscillator be
less accurate (–53.12% to +56.25% deviation).
All interrupts remain active. Only the occurrence of an interrupt
wakes the part from sleep. The Stop bit in the System Status and
Control Register (CPU_SCR) must be cleared for a part to
resume out of sleep. The Global Interrupt Enable bit of the CPU
Flags Register (CPU_F) does not have any effect. Any
unmasked interrupt wakes the system up. As a result, any
interrupts not intended for waking must be disabled through the
Interrupt Mask Registers.
Document Number: 001-07611 Rev *I
1
0
W
0
W
0
When the CPU enters sleep mode, the internal oscillator is
stopped. When the CPU comes out of sleep mode, it is running
on the internal oscillator. The internal oscillator recovery time is
three clock cycles of the Internal 32 kHz Low power Oscillator.
On exiting sleep mode, when the clock is stable and the delay
time has expired, the instruction immediately following the sleep
instruction is executed before the interrupt service routine (if
enabled).
The Sleep interrupt allows the microcontroller to wake up periodically and poll system components while maintaining very low
average power consumption. The Sleep interrupt may also be
used to provide periodic interrupts during non sleep modes.
Sleep Sequence
The Sleep bit is an input into the sleep logic circuit. This circuit is
designed to sequence the device into and out of the hardware
sleep state. The hardware sequence to put the device to sleep
is shown in Figure 12 on page 34 and is defined as follows.
1. Firmware sets the SLEEP bit in the CPU_SCR0 register. The
Bus Request (BRQ) signal to the CPU is immediately
asserted. This is a request by the system to halt CPU
operation at an instruction boundary. The CPU samples BRQ
on the positive edge of CPUCLK.
2. Due to the specific timing of the register write, the CPU issues
a Bus Request Acknowledge (BRA) on the following positive
edge of the CPU clock. The sleep logic waits for the following
negative edge of the CPU clock and then asserts a
system-wide Power Down (PD) signal. In Figure 12 on page
34 the CPU is halted and the system-wide power down signal
is asserted.
Page 33 of 72
CYRF69103
3. The system-wide PD (power down) signal controls several
major circuit blocks: The Flash memory module, the internal
24 MHz oscillator, the EFTB filter and the bandgap voltage
reference. These circuits transition into a zero power state.
The only operational circuits on chip are the Low Power
oscillator, the bandgap refresh circuit, and the supply voltage
monitor (POR/LVD) circuit.
Low Power in Sleep Mode
To achieve the lowest possible power consumption during
suspend or sleep, the following conditions are observed in
addition to considerations for the sleep timer:
■
All GPIOs are set to outputs and driven low
■
Clear P11CR[0], P10CR[0]
■
Set P10CR[1]
■
To avoid current consumption make sure ITMRCLK and
TCPCLK are not sourced by either low power 32 kHz oscillator
or 24 MHz crystal-less oscillator.
All the other blocks go to the power down mode automatically on
suspend.
The following steps are user configurable and help in reducing
the average suspend mode power consumption:
1. Configure the power supply monitor at a large regular
intervals, control register bits are 1,EB[7:6] (Power system
sleep duty cycle PSSDC[1:0]).
2. Configure the Low power oscillator into low power mode,
control register bit is LOPSCTR[7].
Figure 12. Sleep Timing
Firmware write to SCR
SLEEP bit causes an
immediate BRQ
CPU captures
BRQ on next
CPUCLK edge
CPU
responds
with a BRA
On the falling edge of
CPUCLK, PD is asserted.
The 24/48 MHz system clock
is halted; the Flash and
bandgap are powered down
CPUCLK
IOW
SLEEP
BRQ
BRA
PD
Wakeup Sequence
When asleep, the only event that can wake the system up is an
interrupt. The global interrupt enable of the CPU flag register
does not need to be set. Any unmasked interrupt wakes the
system up. It is optional for the CPU to actually take the interrupt
after the wakeup sequence. The wakeup sequence is
synchronized to the 32 kHz clock. This is done to sequence a
startup delay and enable the Flash memory module enough time
to power up before the CPU asserts the first read access.
Another reason for the delay is to enable the oscillator, Bandgap,
and LVD/POR circuits time to settle before actually being used
in the system. As shown in Figure 13 on page 35, the wakeup
sequence is as follows:
1. The wakeup interrupt occurs and is synchronized by the
negative edge of the 32 kHz clock.
2. At the following positive edge of the 32 kHz clock, the
system-wide PD signal is negated. The Flash memory
Document Number: 001-07611 Rev *I
module, internal oscillator, EFTB, and bandgap circuit are all
powered up to a normal operating state.
3. At the following positive edge of the 32 kHz clock, the current
values for the precision POR and LVD have settled and are
sampled.
4. At the following negative edge of the 32 kHz clock (after about
15 µs nominal), the BRQ signal is negated by the sleep logic
circuit. On the following CPUCLK, BRA is negated by the CPU
and instruction execution resumes. Note that in Figure 13 on
page 35 fixed function blocks, such as Flash, internal oscillator, EFTB, and bandgap, have about 15 µs start up. The
wakeup times (interrupt to CPU operational) ranges from
75 µs to 105 µs.
Page 34 of 72
CYRF69103
Figure 13. Wakeup Timing
S leep Tim er or G P IO
interrupt occurs
Interrupt is double sam pled
by 32K clock and P D is
negated to system
C P U is restarted
after 90 m s
(nom inal)
C LK32K
IN T
SLEEP
PD
BAN D G AP
EN ABLE
SAM PLE
SAM PLE
LVD /PO R
C PU C LK/
24M H z
(N ot to Scale)
BR Q
BR A
C PU
Document Number: 001-07611 Rev *I
Page 35 of 72
CYRF69103
Low Voltage Detect Control
Table 42. Low Voltage Control Register (LVDCR) [0x1E3] [R/W]
Bit #
7
Field
6
Reserved
5
4
PORLEV[1:0]
3
2
Reserved
1
0
VM[2:0]
Read/Write
–
–
R/W
R/W
–
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
This register controls the configuration of the Power on Reset/Low voltage Detection circuit. This register can only be accessed
in the second bank of I/O space. This requires setting the XIO bit in the CPU flags register.
Bits 7:6
Reserved
Bits 5:4
PORLEV[1:0]
This field controls the level below which the precision power on reset (PPOR) detector generates a reset
0 0 = 2.7 V Range (trip near 2.6 V)
0 1 = 3 V Range (trip near 2.9 V)
1 0 = Reserved
1 1 = PPOR does not generate a reset, but values read from the Voltage Monitor Comparators Register (Table
43 on page 37) give the internal PPOR comparator state with trip point set to the 3 V range setting.
Bit 3
Reserved
Bits 2:0
VM[2:0]
This field controls the level below which the low voltage-detect trips—possibly generating an interrupt and the
level at which the Flash is enabled for operation.
VM[2:0]
LVD Trip Point Typ. (V)
000
2.7
001
2.92
010
3.02
011
3.13
100
101
110
111
Document Number: 001-07611 Rev *I
Page 36 of 72
CYRF69103
POR Compare State
Table 43. Voltage Monitor Comparators Register (VLTCMP) [0x1E4] [R]
Bit #
7
6
5
Field
4
3
2
Reserved
1
0
LVD
PPOR
Read/Write
–
–
–
–
–
–
R
R
Default
0
0
0
0
0
0
0
0
This read-only register allows reading the current state of the Low voltage Detection and Precision-Power-On-Reset
comparators:
Bits 7:2
Reserved
Bit 1
LVD
This bit is set to indicate that the low voltage detect comparator has tripped, indicating that the supply voltage
has gone below the trip point set by VM[2:0] (see Table 42 on page 36).
0 = No low voltage detect event
1 = A low voltage detect has tripped
Bit 0
PPOR
This bit is set to indicate that the precision-power-on-reset comparator has tripped, indicating that the supply
voltage is below the trip point set by PORLEV[1:0]:
0 = No precision-power-on-reset event
1 = A precision-power-on-reset event has tripped
Note This register can only be accessed in the second bank of I/O space. This requires setting the XIO bit in the CPU flags
register
ECO Trim Register
Table 44. ECO (ECO_TR) [0x1EB] [R/W]
Bit #
Field
Read/Write
Default
7
6
5
4
3
Sleep Duty Cycle [1:0]
2
1
0
Reserved
R/W
R/W
–
–
–
–
–
–
0
0
0
0
0
0
0
0
This register controls the ratios (in numbers of 32 kHz clock periods) of ‘on’ time versus ‘off’ time for LVD and POR detection
circuit.
Bits 7:6
Sleep Duty Cycle [1:0]
0 0 = 1/128 periods of the Internal 32 kHz Low-speed Oscillator
0 1 = 1/512 periods of the Internal 32 kHz Low-speed Oscillator
1 0 = 1/32 periods of the Internal 32 kHz Low-speed Oscillator
1 1 = 1/8 periods of the Internal 32 kHz Low speed Oscillator
Note This register can only be accessed in the second bank of I/O space. This requires setting the XIO bit in the CPU flags
register
Document Number: 001-07611 Rev *I
Page 37 of 72
CYRF69103
General Purpose I/O Ports
The general purpose I/O ports are discussed in the following sections.
Port Data Registers
Table 45. P0 Data Register (P0DATA)[0x00] [R/W]
Bit #
7
Field
P0.7
Read/Write
R/W
Default
0
6
5
Reserved
4
3
2
1
0
P0.4/INT2
P0.3/INT1
Reserved
P0.1
Reserved
R/W
R/W
–
R/W
–
0
0
0
0
–
–
–
–
This register contains the data for Port 0. Writing to this register sets the bit values to be output on output enabled pins. Reading
from this register returns the current state of the Port 0 pins.
Bit 7
P0.7 Data
Bits 6:5
Reserved
Bits 4:3
P0.4–P0.3Data/INT2–INT1
In addition to their use as the P0.4–P0.3 GPIOs, these pins can also be used for the alternative functions as the
Interrupt pins (INT1–INT2). To configure the P0.4–P0.3 pins, refer to the P0.3/INT1–P0.4/INT2 Configuration
Register (Table 49 on page 40).
Bit 2
Reserved
Bit 1
P0.1 Data
Bit 0
Reserved
Table 46. P1 Data Register (P1DATA) [0x01] [R/W]
Bit #
7
6
Field
P1.7
P1.6
Read/Write
R/W
R/W
R/W
R/W
0
0
0
0
Default
5
4
P1.5/SMOSI P1.4/SCLK
3
2
1
0
P1.3/SSEL
P1.2
P1.1
P1.0
R/W
R/W
R/W
R/W
0
0
0
–
This register contains the data for Port 1. Writing to this register sets the bit values to be output on output enabled pins. Reading
from this register returns the current state of the Port 1 pins.
Bits 7
P1.7
Bits 6
P1.6 or alternate function of SMOSI in a 4-wire SPI
Bits 5:3
P1.5–P1.3 Data/3-wire SPI Pins (SMISO/SMOSI, SCLK, SSEL)
In addition to their use as the P1.6–P1.3 GPIOs, these pins can also be used for the alternative function as the
SPI interface pins. To configure the P1.6–P1.3 pins, refer to the P1.3–P1.6 Configuration Register (Table 54 on
page 42)
Bits 2:1
P1.2–P1.1
Bit 0
P1.0
Table 47. P2 Data Register (P2DATA) [0x02] [R/W]
Bit #
7
6
Field
5
4
3
2
1
Reserved
0
P2.1–P2.0
Read/Write
–
R/W
R/W
Default
–
0
0
This register contains the data for Port 2. Writing to this register sets the bit values to be output on output enabled pins. Reading
from this register returns the current state of the Port 2 pins.
Bits 7:2
P2 Data [7:2]
Bits 1:0
P2 Data [1:0]
Document Number: 001-07611 Rev *I
Page 38 of 72
CYRF69103
GPIO Port Configuration
High Sink
All the GPIO configuration registers have common configuration
controls. The following are the bit definitions of the GPIO
configuration registers. By default all GPIOs are configured as
inputs. To prevent the inputs from floating, the pull up resistors
are enabled. Firmware needs to configure each of the GPIOs
before use.
When set, the output can sink up to 50 mA.
Int Enable
When set, the Int Enable bit allows the GPIO to generate
interrupts. Interrupt generate can occur regardless of whether
the pin is configured for input or output. All interrupts are edge
sensitive, however for any interrupt that is shared by multiple
sources (that is, Ports 2, 3, and 4) all inputs must be deasserted
before a new interrupt can occur.
When clear, the corresponding interrupt is disabled on the pin.
It is possible to configure GPIOs as outputs, enable the interrupt
on the pin and then to generate the interrupt by driving the
appropriate pin state. This is useful in test and may have value
in applications.
Int Act Low
When clear, the corresponding interrupt is active HIGH. When
set, the interrupt is active LOW. For P0.3–P0.4 Int act Low clear
causes interrupts to be active on the rising edge. Int act Low set
causes interrupts to be active on the falling edge.
When clear, the output can sink up to 8 mA.
Open Drain
When set, the output on the pin is determined by the Port Data
Register. If the corresponding bit in the Port Data Register is set,
the pin is in high impedance state. If the corresponding bit in the
Port Data Register is clear, the pin is driven LOW.
When clear, the output is driven LOW or HIGH.
Pull up Enable
When set the pin has a 7K pull up to VDD.
When clear, the pull up is disabled.
Output Enable
When set, the output driver of the pin is enabled.
When clear, the output driver of the pin is disabled.
For pins with shared functions there are some special cases.
P0.0 (CLKIN) and P0.1 (CLKOUT) can not be output enabled
when the crystal oscillator is enabled. Output enables for these
pins are overridden by XOSC Enable.
TTL Thresh
P1.3 (SSEL), P1.4 (SCLK), P1.5 (SMOSI) and P1.6 (SMISO)
can be used for their dedicated functions or for GPIO. To enable
the pin for GPIO use, clear the corresponding SPI Use bit or the
Output Enable has no effect.
When set, the input has TTL threshold. When clear, the input has
standard CMOS threshold.
SPI Use
Important Note The GPIOs default to CMOS threshold. User’s
firmware needs to configure the threshold to TTL mode if
necessary.
The P1.3 (SSEL), P1.4 (SCLK), P1.5 (SMOSI) and P1.6
(SMISO) pins can be used for their dedicated functions or for
GPIO. To enable the pin for GPIO, clear the corresponding SPI
Use bit. The SPI function controls the output enable for its
dedicated function pins when their GPIO enable bit is clear.
Table 48. P0.1 Configuration (P01CR) [0x06] R/W]
Bit #
Field
Read/Write
Default
7
6
5
4
3
2
1
0
Reserved
Int Enable
Int Act Low
TTL Thresh
High Sink
Open Drain
Pull up
Enable
Output
Enable
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
This register is used to configure P0.1. In the CYRF69103, only 8 mA sink drive capability is available on this pin regardless
of the setting of the High Sink bit.
If this pin is used as a general purpose output it draws current. This pin must be configured as an input to reduce current draw.
Bit 7
Reserved
Bit 6
see Int Enable
Bit 5
see Int Act Low
Bit 4
see TTL Thresh
Bit 3
see High Sink
Bit 2
see Open Drain
Bit 1
see Pull up Enable
Bit 0
see Output Enable
Document Number: 001-07611 Rev *I
Page 39 of 72
CYRF69103
Table 49. P0.3–P0.4 Configuration (P03CR–P04CR) [0x08–0x09] [R/W]
Bit #
7
6
Reserved
Field
5
4
3
2
1
0
Int Act Low
TTL Thresh
Reserved
Open Drain
Pull up
Enable
Output
Enable
Read/Write
–
–
R/W
R/W
–
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
These registers control the operation of pins P0.3–P0.4 respectively. These pins are shared between the P0.3–P0.4 GPIOs
and the INT1–INT2. The INT1–INT2 interrupts are different than all the other GPIO interrupts. These pins are connected
directly to the interrupt controller to provide three edge-sensitive interrupts with independent interrupt vectors. These interrupts
occur on a rising edge when Int act Low is clear and on a falling edge when Int act Low is set. These pins are enabled as
interrupt sources in the interrupt controller registers (Table 75 on page 55 and Table 73 on page 54).
To use these pins as interrupt inputs, configure them as inputs by clearing the corresponding Output Enable. If the INT1–INT2
pins are configured as outputs with interrupts enabled, firmware can generate an interrupt by writing the appropriate value to
the P0.3, and P0.4 data bits in the P0 Data Register.
Regardless of whether the pins are used as Interrupt or GPIO pins the Int Enable, Int act Low, TTL Threshold, Open Drain,
and Pull up Enable bits control the behavior of the pin.
The P0.3/INT1–P0.4/INT2 pins are individually configured with the P03CR (0x08), and P04CR (0x09) respectively.
Note Changing the state of the Int Act Low bit can cause an unintentional interrupt to be generated. When configuring these
interrupt sources, it is best to follow the following procedure:
1. Disable interrupt source
2. Configure interrupt source
3. Clear any pending interrupts from the source
4. Enable interrupt source
Table 50. P0.7 Configuration (P07CR) [0x0C] [R/W]
Bit #
7
6
5
4
3
2
1
0
Reserved
Int Enable
Int Act Low
TTL Thresh
Reserved
Open Drain
Pull up
Enable
Output
Enable
Read/Write
–
R/W
R/W
R/W
–
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
Field
This register controls the operation of pin P0.7.
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reserved
see Int Enable
see Int Act Low
see TTL Thresh
Reserved
see Open Drain
see Pull up Enable
see Output Enable
Document Number: 001-07611 Rev *I
Page 40 of 72
CYRF69103
Table 51. P1.0 Configuration (P10CR) [0x0D] [R/W]
Bit #
Field
Read/Write
Default
7
6
5
4
3
2
1
0
Reserved
Int Enable
Int Act Low
Reserved
Reserved
Reserved
5K pullup
Enable
Output
enable
R/W
R/W
R/W
-
-
-
R/W
R/W
0
0
0
0
0
0
0
0
This register controls the operation of the P1.0 pin.
Note The P1.0 is an open drain only output. It can actively drive a signal low, but cannot actively drive a signal high.
Bit 0 This bit enables the output on P1.0. This bit must be cleared in sleep mode.
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Reserved
see Int Enable
see Int Act Low
Reserved
Reserved
Reserved
0 = disables the 5K ohm pull up resistors
1 = enables 5K ohm pull up resistors for both
P1.0 and P1.1 (this is not compatible with USB)
Table 52. P1.1 Configuration (P11CR) [0x0E] [R/W]
Bit #
7
6
5
Reserved
Int Enable
Int Act Low
Read/Write
–
R/W
R/W
–
Default
0
0
0
0
Field
4
3
2
1
0
Open Drain
Reserved
Output
Enable
–
R/W
–
R/W
0
0
0
0
Reserved
This register controls the operation of the P1.1 pin.
The pull up resistor on this pin is enabled by the P10CR Register.
Note There is no 2 mA sourcing capability on this pin. The pin can only sink 5 mA at VOL3 section.
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reserved
see Int Enable
see Int Act Low
Reserved
Reserved
see Open Drain
Reserved
see Output Enable
Document Number: 001-07611 Rev *I
Page 41 of 72
CYRF69103
Table 53. P1.2 Configuration (P12CR) [0x0F] [R/W]
Bit #
Field
Read/Write
Default
7
6
5
4
3
2
1
0
CLK Output
Int Enable
Int Act Low
TTL
Threshold
Reserved
Open Drain
Pull up
Enable
Output
Enable
R/W
R/W
R/W
R/W
–
R/W
R/W
R/W
0
0
0
0
0
0
0
0
This register controls the operation of the P1.2.
Bit 7
CLK Output
0 = The internally selected clock is not sent out onto P1.2 pin.
1 = When CLK Output is set, the internally selected clock is sent out onto P1.2 pin.
Bit 6
see Int Enable
Bit 5
see Int Act Low
Bit 4
Reserved
Bit 3
see High Sink
Bit 2
see Open Drain
Bit 1
see Pull up Enable
Bit 0
see Output Enable
Table 54. P1.3 Configuration (P13CR) [0x10] [R/W]
Bit #
7
6
5
4
3
2
1
0
Reserved
Int Enable
Int Act Low
Reserved
High Sink
Open Drain
Pull up
Enable
Output
Enable
Read/Write
–
R/W
R/W
–
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
Field
This register controls the operation of the P1.3 pin.
The P1.3 GPIO’s threshold is always set to TTL.
When the SPI hardware is enabled, the output enable and output state of the pin is controlled by the SPI circuitry. When the
SPI hardware is disabled, the pin is controlled by the Output Enable bit and the corresponding bit in the P1 data register.
Regardless of whether the pin is used as an SPI or GPIO pin the Int Enable, Int act Low, High Sink, Open Drain, and Pull up
Enable control the behavior of the pin.
50 mA sink drive capability is available.
Bit 7
Reserved
Bit 6
see Int Enable
Bit 5
see Int Act Low
Bit 4
Reserved
Bit 3
see High Sink
Bit 2
see Open Drain
Bit 1
see Pull up Enable
Bit 0
see Output Enable
Document Number: 001-07611 Rev *I
Page 42 of 72
CYRF69103
Table 55. P1.4–P1.6 Configuration (P14CR–P16CR) [0x11–0x13] [R/W]
Bit #
Field
Read/Write
Default
7
6
5
4
3
2
1
0
SPI Use
Int Enable
Int Act Low
Reserved
High Sink
Open Drain
Pull up
Enable
Output
Enable
R/W
R/W
R/W
–
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
These registers control the operation of pins P1.4–P1.6, respectively.
The P1.4–P1.6 GPIO’s threshold is always set to TTL.
When the SPI hardware is enabled, pins that are configured as SPI Use have their output enable and output state controlled
by the SPI circuitry. When the SPI hardware is disabled or a pin has its SPI Use bit clear, the pin is controlled by the Output
Enable bit and the corresponding bit in the P1 data register.
Regardless of whether any pin is used as an SPI or GPIO pin the Int Enable, Int act Low, High Sink, Open Drain, and Pull up
Enable control the behavior of the pin.
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SPI Use
0 = Disable the SPI alternate function. The pin is used as a GPIO
1 = Enable the SPI function. The SPI circuitry controls the output of the pin
see Int Enable
see Int Act Low
Reserved
see High Sink
see Open Drain
see Pull up Enable
see Output Enable
Note For Comm Modes 01 or 10 (SPI Master or SPI Slave, see Table 59 on page 46)
When configured for SPI (SPI Use = 1 and Comm Modes [1:0] = SPI Master or SPI Slave mode), the input/output direction
of pins P1.3, P1.5, and P1.6 is set automatically by the SPI logic. However, pin P1.4's input/output direction is NOT
automatically set; it must be explicitly set by firmware. For SPI Master mode, pin P1.4 must be configured as an output; for
SPI Slave mode, pin P1.4 must be configured as an input.
Table 56. P1.7 Configuration (P17CR) [0x14] [R/W]
Bit #
7
6
5
4
3
2
1
0
Reserved
Int Enable
Int Act Low
Reserved
High Sink
Open Drain
Pull up
Enable
Output
Enable
Read/Write
–
R/W
R/W
–
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
Field
This register controls the operation of pin P1.7.
50 mA sink drive capability is available. The P1.7 GPIO’s threshold is always set to TTL.
Bit 7
Reserved
Bit 6
see Int Enable
Bit 5
see Int Act Low
Bit 4
Reserved
Bit 3
see High Sink
Bit 2
see Open Drain
Bit 1
see Pull up Enable
Bit 0
see Output Enable
Document Number: 001-07611 Rev *I
Page 43 of 72
CYRF69103
Table 57. P2 Configuration (P2CR) [0x15] [R/W]
Bit #
7
6
5
4
3
2
1
0
Reserved
Int Enable
Int Act Low
TTL Thresh
High Sink
Open Drain
Pull up
Enable
Output
Enable
Read/Write
–
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
Field
This register controls the operation of pins P2.0–P2.1.
Bit 7
Reserved
Bit 6
see Int Enable
Bit 5
see Int Act Low
Bit 4
see TTL Thresh
Bit 3
see High Sink
Bit 2
see Open Drain
Bit 1
see Pull up Enable
Bit 0
see Output Enable
GPIO Configurations for Low Power Mode
To ensure low power mode, unbonded GPIO pins in CYRF69103 must be placed in a non-floating state. The following assembly code
snippet shows how this is achieved. This snippet can be added as a part of the initialization routine.
//Code Snippet for addressing unbonded GPIOs
mov A, 01h
mov reg[1Fh],A
mov A, 01h
mov reg[16h],A // Port3 Configuration register - Enable output
mov A, 00h
mov reg[03h],A // Asserting P3.0 to P3.7 outputs to '0'
//Port 2 configurations
mov A,01h
mov reg[15h],A //Port 2 Configuration register -Enable output
mov A,00h
mov reg[02h],A //Asserting P2.0 to P2.7 outputs to ‘0’
mov A, 01h
mov reg[05h],A // Port0.0 Configuration register - Enable output
mov reg[07h],A // Port0.2 Configuration register - Enable output
mov reg[0Ah],A // Port0.5 Configuration register - Enable output
mov reg[0Bh],A // Port0.6 Configuration register - Enable output
mov A,reg[00h]
mov A,00h
and A,9Ah
mov reg[00h], A // Asserting outputs '0' to pins in port 1
// NOTE: The code fragment in italics is to be used only if your application configures P2.0 and
P2.1 as push-pull outputs.
When writing to port 0, to access GPIOs P0.1,3,4,7, mask bits 0,2,5,6. Failing to do so voids the low power.
Document Number: 001-07611 Rev *I
Page 44 of 72
CYRF69103
Serial Peripheral Interface (SPI)
The SPI Master/Slave Interface core logic runs on the SPI clock domain. The SPI clock is a divider off of the CPUCLK when in Master
Mode. SPI is a four-pin serial interface comprised of a clock, an enable, and two data pins.
Figure 14. SPI Block Diagram
Register Block
SCK Speed Sel
SCK Clock Generation
Master/Slave Sel
SCK Clock Select
SCK Polarity
SCK Clock Phase/Polarity
Select
SCK Phase
Little Endian Sel
SCK_OE
SCK
SCK
LE_SEL
GPIO Block
SS_N
SS_N
SPI State Machine
SS_N_OE
SS_N
Data (8 bit)
Load
MISO_OE
Output Shift Buffer
Empty
Master/Slave Set
MISO/MOSI
Crossbar
MISO
SCK
LE_SEL
Shift Buffer
MOSI_OE
MOSI
Data (8 bit)
Input Shift Buffer
Load
Full
Sclk Output Enable
Slave Select Output Enable
Master IN, Slave Out OE
Master Out, Slave In, OE
Document Number: 001-07611 Rev *I
SCK_OE
SS_N_OE
MISO_OE
MOSI_OE
Page 45 of 72
CYRF69103
SPI Data Register
Table 58. SPI Data Register (SPIDATA) [0x3C] [R/W]
Bit #
7
6
5
4
Field
Read/Write
Default
3
2
1
0
SPIData[7:0]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
When read, this register returns the contents of the receive buffer. When written, it loads the transmit holding register.
Bits 7:0
SPI Data [7:0]
When an interrupt occurs to indicate to firmware that an byte of receive data is available, or the transmitter holding register is empty,
firmware has 7 SPI clocks to manage the buffers – to empty the receiver buffer, or to refill the transmit holding register. Failure to meet
this timing requirement results in incorrect data transfer.
SPI Configure Register
Table 59. SPI Configure Register (SPICR) [0x3D] [R/W]
Bit #
7
6
Field
Swap
LSB First
Read/Write
R/W
R/W
R/W
R/W
0
0
0
0
Default
5
4
Comm Mode
3
2
1
0
CPOL
CPHA
R/W
R/W
R/W
R/W
0
0
0
0
SCLK Select
Bit 7
Swap
0 = Swap function disabled.
1 = The SPI block swaps its use of SMOSI and SMISO. Among other things, this can be useful in implementing
single wire SPI-like communications.
Bit 6
LSB First
0 = The SPI transmits and receives the MSB (Most Significant Bit) first.
1 = The SPI transmits and receives the LSB (Least Significant Bit) first.
Bits 5:4
Comm Mode [1:0]
0 0: All SPI communication disabled.
0 1: SPI master mode
1 0: SPI slave mode
1 1: Reserved
Bit 3
CPOL
This bit controls the SPI clock (SCLK) idle polarity.
0 = SCLK idles low
1 = SCLK idles high
Bit 2
CPHA
The Clock Phase bit controls the phase of the clock on which data is sampled. Table 60 on page 47 shows the
timing for the various combinations of LSB First, CPOL, and CPHA.
Bits 1:0
SCLK Select
This field selects the speed of the master SCLK. When in master mode, SCLK is generated by dividing the base
CPUCLK.
Important Note for Comm Modes 01b or 10b (SPI Master or SPI Slave):
When configured for SPI, (SPI Use = 1 – Table 55 on page 43), the input/output direction of pins P1.3, P1.5, and P1.6 is set
automatically by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by
firmware. For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured
as an input.
Document Number: 001-07611 Rev *I
Page 46 of 72
CYRF69103
Table 60. SPI Mode Timing vs. LSB First, CPOL and CPHA
LSB First CPHA
0
0
CPOL
Diagram
0
SCLK
SSEL
D AT A
0
0
X
MSB
B it 7
B it 6
B it 5
B it 4
B it 3
B it 2
X
LSB
1
SC LK
SSEL
DAT A
0
1
X
MSB
B it 7
B it 6
B it 5
B it 4
B it 3
B it 2
X
LSB
0
SC LK
SSEL
DAT A
0
1
X
MSB
B it 7
B it 6
B it 5
B it 4
B it 3
B it 2
LS B
X
X
MS B
B it 7
B it 6
B it 5
B it 4
B it 3
B it 2
LS B
X
1
SC L K
SSEL
D AT A
1
0
0
SCLK
SSEL
DAT A
1
0
X
LSB
B it 2
B it 3
B it 4
B it 5
B it 6
B it 7
MS B
X
X
LSB
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
MSB
X
1
SCLK
SSEL
DAT A
1
1
0
SCLK
SSEL
DAT A
1
1
X
LSB
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
MSB
X
X
LSB
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
MSB
X
1
SC LK
SSEL
DAT A
Document Number: 001-07611 Rev *I
Page 47 of 72
CYRF69103
Timer Registers
Table 61. SPI SCLK Frequency
SCLK CPUCLK
Select Divisor
00
6
SCLK Frequency when
CPUCLK = 12 MHz
All timer functions of the CYRF69103 are provided by a single
timer block. The timer block is asynchronous from the CPU clock.
The 16-bit free running counter is used as the time-base for timer
captures and can also be used as a general time-base by
software.
2 MHz
01
12
1 MHz
10
48
250 kHz
11
96
125 kHz
Registers
Free Running Counter
SPI Interface Pins
The SPI interface between the radio function and MCU function
uses pins P1.3–P1.5 and optionally P1.6. These pins are
configured using the P1.3 and P1.4–P1.6 Configuration.
The 16-bit free running counter is clocked by a 4 or 6 MHz
source. It can be read in software for use as a general purpose
time base. When the low order byte is read, the high order byte
is registered. Reading the high order byte reads this register
allowing the CPU to read the 16-bit value atomically (loads all
bits at one time). The free running timer generates an interrupt
at 1024 s rate. It can also generate an interrupt when the free
running counter overflow occurs—every 16.384 ms. This allows
extending the length of the timer in software.
Figure 15. 16-bit Free Running Counter Block Diagram
O verflow
Interrupt
Tim er Capture
C lock
16-bit Free
Running Counter
1024-µs
Tim er
Interrupt
Table 62. Free Running Timer Low Order Byte (FRTMRL) [0x20] [R/W]
Bit #
7
6
5
R/W
R/W
R/W
R/W
0
0
0
0
Field
Read/Write
Default
4
3
2
1
0
R/W
R/W
R/W
R/W
0
0
0
0
Free Running Timer [7:0]
Bits 7:0
Free running Timer [7:0]
This register holds the low order byte of the 16-bit free running timer. Reading this register causes the high order byte to be
moved into a holding register allowing an automatic read of all 16 bits simultaneously.
For reads, the actual read occurs in the cycle when the low order is read. For writes the actual time the write occurs is the
cycle when the high order is written.
When reading the free running timer, the low order byte must be read first and the high order second. When writing, the low
order byte must be written first then the high order byte.
Document Number: 001-07611 Rev *I
Page 48 of 72
CYRF69103
Table 63. Free Running Timer High-Order Byte (FRTMRH) [0x21] [R/W]
Bit #
7
6
5
Field
Read/Write
Default
4
3
2
1
0
Free Running Timer [15:8]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Bits 7:0
Free Running Timer [15:8]
When reading the free running timer, the low order byte must be read first and the high order second. When writing, the low
order byte must be written first then the high order byte.
Table 64. Programmable Interval Timer Low (PITMRL) [0x26] [R]
Bit #
7
6
5
Read/Write
R
R
R
R
Default
0
0
0
0
Field
4
3
2
1
0
R
R
R
R
0
0
0
0
Prog Interval Timer [7:0]
Bits 7:0
Prog Interval Timer [7:0]
This register holds the low order byte of the 12-bit programmable interval timer. Reading this register causes the high order
byte to be moved into a holding register allowing an automatic read of all 12 bits simultaneously.
Table 65. Programmable Interval Timer High (PITMRH) [0x27] [R]
Bit #
7
6
5
4
3
Read/Write
--
--
--
--
R
R
R
R
Default
0
0
0
0
0
0
0
0
Field
Reserved
2
1
0
Prog Interval Timer [11:8]
Bits 7:4
Reserved
Bits 3:0
Prog Internal Timer [11:8]
This register holds the high order nibble of the 12-bit programmable interval timer. Reading this register returns the high order
nibble of the 12-bit timer at the instant that the low order byte was last read.
Table 66. Programmable Interval Reload Low (PIRL) [0x28] [R/W]
Bit #
7
6
5
Field
Read/Write
Default
4
3
2
1
0
Prog Interval [7:0]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Bits 7:0
Prog Interval [7:0]
This register holds the lower 8 bits of the timer. While writing into the 12-bit reload register, write lower byte first then the higher
nibble.
Document Number: 001-07611 Rev *I
Page 49 of 72
CYRF69103
Table 67. Programmable Interval Reload High (PIRH) [0x29] [R/W]
Bit #
7
6
Field
5
4
3
Reserved
2
1
0
Prog Interval[11:8]
Read/Write
--
--
--
--
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
Bits [7:4] Reserved
Bits 3:0
Prog Interval [11:8]
This register holds the higher 4 bits of the timer. While writing into the 12-bit reload register, write lower byte first then the
higher nibble.
Figure 16. 16-Bit Free Running Counter Loading Timing Diagram
clk_sys
write
valid
addr
write data
FRT reload
ready
Clk Timer
12b Prog Timer
12b reload
interrupt
12-bit programmable timer load timing
Capture timer
clk
16b free running
counter load
16b free
running counter
00A0 00A1 00A2 00A3 00A4 00A5 00A6 00A7 00A8 00A9 00AB 00AC 00AD 00AE 00AF 00B0 00B1 00B2 ACBE ACBF ACC0
16-bit free running counter loading timing
Document Number: 001-07611 Rev *I
Page 50 of 72
CYRF69103
Figure 17. Memory Mapped Registers Read/Write Timing Diagram
clk_sys
rd_wrn
Valid
Addr
rdata
wdata
Memory mapped registers Read/Write timing diagram
Interrupt Controller
Table 68. Interrupt Priorities, Address, Name (continued)
Interrupt
Priority
Interrupt
Address
16
0040h
17
0044h
16-bit Free Running Timer Wrap
18
0048h
INT2
19
004Ch
Reserved
The following table lists all interrupts and the priorities that are
available in the CYRF69103.
20
0050h
GPIO Port 2
21
0054h
Reserved
Table 68. Interrupt Priorities, Address, Name
22
0058h
Reserved
23
005Ch
Reserved
24
0060h
Reserved
25
0064h
Sleep Timer
The interrupt controller and its associated registers allow the
user’s code to respond to an interrupt from almost every
functional block in the CYRF69103 devices. The registers
associated with the interrupt controller allow interrupts to be
disabled either globally or individually. The registers also provide
a mechanism by which a user may clear all pending and posted
interrupts, or clear individual posted or pending interrupts.
Interrupt
Priority
Interrupt
Address
0
0000h
Name
Reset
1
0004h
POR/LVD
2
0008h
Reserved
3
000Ch
SPI Transmitter Empty
4
0010h
SPI Receiver Full
5
0014h
GPIO Port 0
6
0018h
GPIO Port 1
7
001Ch
INT1
8
0020h
Reserved
9
0024h
Reserved
10
0028h
Reserved
11
002Ch
Reserved
12
0030h
Reserved
13
0034h
1 ms Interval timer
14
0038h
Programmable Interval Timer
15
003Ch
Reserved
Document Number: 001-07611 Rev *I
Name
Reserved
Architectural Description
An interrupt is posted when its interrupt conditions occur. This
results in the flip-flop in Figure 18 on page 52 clocking in a ‘1’.
The interrupt remains posted until the interrupt is taken or until it
is cleared by writing to the appropriate INT_CLRx register.
A posted interrupt is not pending unless it is enabled by setting
its interrupt mask bit (in the appropriate INT_MSKx register). All
pending interrupts are processed by the Priority Encoder to
determine the highest priority interrupt which is taken by the M8C
if the Global Interrupt Enable bit is set in the CPU_F register.
Disabling an interrupt by clearing its interrupt mask bit (in the
INT_MSKx register) does not clear a posted interrupt, nor does
it prevent an interrupt from being posted. It simply prevents a
posted interrupt from becoming pending.
Nested interrupts can be accomplished by reenabling interrupts
inside an interrupt service routine. To do this, set the IE bit in the
Flag Register.
A block diagram of the CYRF69103 Interrupt Controller is shown
in Figure 18 on page 52.
Page 51 of 72
CYRF69103
Figure 18. Interrupt Controller Block Diagram
Priority
Encoder
Interrupt Taken
or
Interrupt Vector
INT_CLRx Write
Posted
Interrupt
Pending
Interrupt
1
D
... ...
R
Interrupt
Request
Q
Interrupt
Source
(Timer,
GPIO, etc.)
M8C Core
CPU_F[0]
GIE
INT_MSKx
Mask Bit Setting
Interrupt Processing
The sequence of events that occur during interrupt processing is
as follows:
1. An interrupt becomes active, either because:
a. The interrupt condition occurs (for example, a timer expires).
b. A previously posted interrupt is enabled through an update
of an interrupt mask register.
c. An interrupt is pending and GIE is set from 0 to 1 in the CPU
Flag register.
2. The current executing instruction finishes.
3. The internal interrupt is dispatched, taking 13 cycles. During
this time, the following actions occur:
a. The MSB and LSB of Program Counter and Flag registers
(CPU_PC and CPU_F) are stored onto the program stack
by an automatic CALL instruction (13 cycles) generated
during the interrupt acknowledge process.
b. The PCH, PCL, and Flag register (CPU_F) are stored onto
the program stack (in that order) by an automatic CALL
instruction (13 cycles) generated during the interrupt
acknowledge process.
c. The CPU_F register is then cleared. Because this clears the
GIE bit to 0, additional interrupts are temporarily disabled.
d. The PCH (PC[15:8]) is cleared to zero.
e. The interrupt vector is read from the interrupt controller and
its value placed into PCL (PC[7:0]). This sets the program
counter to point to the appropriate address in the interrupt
table (for example, 0004h for the POR/LVD interrupt).
4. Program execution vectors to the interrupt table. Typically, a
LJMP instruction in the interrupt table sends execution to the
user's Interrupt Service Routine (ISR) for this interrupt.
5. The ISR executes. Note that interrupts are disabled because
GIE = 0. In the ISR, interrupts can be re-enabled if desired by
setting GIE = 1 (care must be taken to avoid stack overflow).
Document Number: 001-07611 Rev *I
6. The ISR ends with a RETI instruction which restores the
Program Counter and Flag registers (CPU_PC and CPU_F).
The restored Flag register re-enables interrupts because GIE
= 1 again.
7. Execution resumes at the next instruction, after the one that
occurred before the interrupt. However, if there are more
pending interrupts, the subsequent interrupts are processed
before the next normal program instruction.
Interrupt Latency
The time between the assertion of an enabled interrupt and the
start of its ISR can be calculated from the following equation.
Latency = Time for current instruction to finish + Time for internal
interrupt routine to execute + Time for LJMP instruction in
interrupt table to execute.
For example, if the 5-cycle JMP instruction is executing when an
interrupt becomes active, the total number of CPU clock cycles
before the ISR begins is as follows:
(1 to 5 cycles for JMP to finish) + (13 cycles for interrupt routine)
+ (7 cycles for LJMP) = 21 to 25 cycles.
In the following example, at 12 MHz, 25 clock cycles take
2.08 µs.
Interrupt Registers
The Interrupt Registers are discussed it the following sections.
Interrupt Clear Register
The Interrupt Clear Registers (INT_CLRx) are used to enable the
individual interrupt sources’ ability to clear posted interrupts.
When an INT_CLRx register is read, any bits that are set
indicates an interrupt has been posted for that hardware
resource. Therefore, reading these registers gives the user the
ability to determine all posted interrupts.
Page 52 of 72
CYRF69103
Table 69. Interrupt Clear 0 (INT_CLR0) [0xDA] [R/W]
Bit #
7
6
5
4
3
2
1
0
Field
GPIO Port 1 Sleep Timer
INT1
GPIO Port 0 SPI Receive SPI Transmit Reserved
POR/LVD
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
When reading this register:
0 = There is no posted interrupt for the corresponding hardware.
1 = Posted interrupt for the corresponding hardware present.
Writing a ‘0’ to the bits clears the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits and to the ENSWINT
(Bit 7 of the INT_MSK3 Register) posts the corresponding hardware interrupt.
The GPIO interrupts are edge-triggered.
Table 70. Interrupt Clear 1 (INT_CLR1) [0xDB] [R/W]
Bit #
7
6
5
Reserved
Prog Interval
Timer
1 ms
Programmable
Interrupt
R/W
0
4
3
2
1
0
Reserved
Field
Read/Write
–
R/W
–
–
–
–
–
Default
0
0
0
0
0
0
0
When reading this register:
0 = There is no posted interrupt for the corresponding hardware.
1 = Posted interrupt for the corresponding hardware present.
Writing a ‘0’ to the bits clears the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT.
Bit 7
Reserved
Table 71. Interrupt Clear 2 (INT_CLR2) [0xDC] [R/W]
Bit #
7
Reserved
6
Reserved
5
Reserved
4
GPIO Port2
3
Reserved
2
INT2
1
16-bit
Counter
Wrap
R/W
0
0
Reserved
Field
Read/Write
–
–
–
R/W
–
R/W
–
Default
0
0
0
0
0
0
0
When reading this register:
0 = There is no posted interrupt for the corresponding hardware
1 = Posted interrupt for the corresponding hardware present.
Writing a ‘0’ to the bits clears the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT
(Bit 7 of the INT_MSK3 Register) posts the corresponding hardware interrupt.
Bits 7,6,5,3,0]Reserved
Interrupt Mask Registers
The Interrupt Mask Registers (INT_MSKx) are used to enable the individual interrupt sources’ ability to create pending interrupts.
There are four Interrupt Mask Registers (INT_MSK0, INT_MSK1, INT_MSK2, and INT_MSK3) that may be referred to in general as
INT_MSKx. If cleared, each bit in an INT_MSKx register prevents a posted interrupt from becoming a pending interrupt (input to the
priority encoder). However, an interrupt can still post even if its mask bit is zero. All INT_MSKx bits are independent of all other
INT_MSKx bits.
If an INT_MSKx bit is set, the interrupt source associated with that mask bit may generate an interrupt that becomes a pending
interrupt.
The Enable Software Interrupt (ENSWINT) bit in INT_MSK3[7] determines the way an individual bit value written to an INT_CLRx
register is interpreted. When is cleared, writing 1's to an INT_CLRx register has no effect. However, writing 0's to an INT_CLRx register,
when ENSWINT is cleared causes the corresponding interrupt to clear. If the ENSWINT bit is set, any 0's written to the INT_CLRx
registers are ignored. However, 1's written to an INT_CLRx register, while ENSWINT is set, cause an interrupt to post for the
corresponding interrupt.
Software interrupts can aid in debugging interrupt service routines by eliminating the need to create system level interactions that are
sometimes necessary to create a hardware-only interrupt.
Document Number: 001-07611 Rev *I
Page 53 of 72
CYRF69103
Table 72. Interrupt Mask 3 (INT_MSK3) [0xDE] [R/W]
Bit #
7
Field
ENSWINT
6
5
4
3
2
1
0
Reserved
Read/Write
R
–
–
–
–
–
–
–
Default
0
0
0
0
0
0
0
0
Bit 7
Bits 6:0
Enable Software Interrupt (ENSWINT)
0 = Disable. Writing 0's to an INT_CLRx register, when ENSWINT is cleared, cause the corresponding interrupt
to clear
1 = Enable. Writing 1's to an INT_CLRx register, when ENSWINT is set, cause the corresponding interrupt to
post
Reserved
Table 73. Interrupt Mask 2 (INT_MSK2) [0xDF] [R/W]
Bit #
7
6
5
4
3
2
1
0
Reserved
Reserved
Reserved
GPIO Port 2
Int Enable
Reserved
INT2 Int
Enable
16-bit
Counter
Wrap Int
Enable
Reserved
Read/Write
–
–
–
R/W
–
R/W
R/W
–
Default
0
0
0
0
0
0
0
0
Field
Bit 7:
Bit 6:
Bit 5:
Bit 4:
Reserved
Reserved
Reserved
GPIO Port 2 Interrupt Enable
0 = Mask GPIO Port 2 interrupt
1 = Unmask GPIO Port 2 interrupt
Bit 3:
Reserved
Bit 2:
INT2 Interrupt Enable
0 = Mask INT2 interrupt
1 = Unmask INT2 interrupt
Bit 1:
16-bit Counter Wrap Interrupt Enable
0 = Mask 16-bit Counter Wrap interrupt
1 = Unmask 16-bit Counter Wrap interrupt
Bit 0:
Reserved
The GPIO interrupts are edge-triggered.
Document Number: 001-07611 Rev *I
Page 54 of 72
CYRF69103
Table 74. Interrupt Mask 1 (INT_MSK1) [0xE1] [R/W]
Bit #
7
Reserved
Field
Read/Write
Default
Bit 7
Bit 6
Bit 5
Bit 4:0
6
5
4
3
Prog Interval 1 ms Timer
Int Enable
Timer
Int Enable
2
1
0
Reserved
R/W
R/W
R/W
–
–
–
–
–
0
0
0
0
0
0
0
0
4
3
2
Reserved
Prog Interval Timer Interrupt Enable
0 = Mask Prog Interval Timer interrupt
1 = Unmask Prog Interval Timer interrupt
1 ms Timer Interrupt Enable
0 = Mask 1 ms interrupt
1 = Unmask 1 ms interrupt
Reserved
Table 75. Interrupt Mask 0 (INT_MSK0) [0xE0] [R/W]
Bit #
7
Field
Read/Write
Default
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
6
GPIO Port 1 Sleep Timer
Int Enable
Int Enable
5
INT1
Int Enable
GPIO Port 0 SPI Receive SPI Transmit
Int Enable
Int Enable
Int Enable
1
0
Reserved
POR/LVD
Int Enable
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
GPIO Port 1 Interrupt Enable
0 = Mask GPIO Port 1 interrupt
1 = Unmask GPIO Port 1 interrupt
Sleep Timer Interrupt Enable
0 = Mask Sleep Timer interrupt
1 = Unmask Sleep Timer interrupt
INT1 Interrupt Enable
0 = Mask INT1 interrupt
1 = Unmask INT1 interrupt
GPIO Port 0 Interrupt Enable
0 = Mask GPIO Port 0 interrupt
1 = Unmask GPIO Port 0 interrupt
SPI Receive Interrupt Enable
0 = Mask SPI Receive interrupt
1 = Unmask SPI Receive interrupt
SPI Transmit Enable
0 = Mask SPI Transmit interrupt
1 = Unmask SPI Transmit interrupt
Reserved
POR/LVD Interrupt Enable
0 = Mask POR/LVD interrupt
1 = Unmask POR/LVD interrupt
Document Number: 001-07611 Rev *I
Page 55 of 72
CYRF69103
Interrupt Vector Clear Register
Table 76. Interrupt Vector Clear Register (INT_VC) [0xE2] [R/W]
Bit #
7
6
5
4
Field
3
2
1
0
Pending Interrupt [7:0]
Read/Write
Default
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
The Interrupt Vector Clear Register (INT_VC) holds the interrupt vector for the highest priority pending interrupt when read,
and when written clears all pending interrupts.
Bits 7:0
Pending Interrupt [7:0]
8-bit data value holds the interrupt vector for the highest priority pending interrupt. Writing to this register clears all pending
interrupts.
Microcontroller Function Register Summary
Addr
Name
7
6
5
4
3
2
1
0
R/W
Default
00
P0DATA
P0.7
Reserved
Reserved
P0.4/INT2
P0.3/INT1
Reserved
P0.1
Reserved
b--bb-b-
00000000
01
P1DATA
P1.7
P1.4/SCLK
P1.3/SSEL
P1.2
P1.1
P1.0
bbbbbbb-
00000000
02
P2DATA
06
P01CR
08–09
P03CR–
P04CR
0C
P07CR
Reserved
0D
P10CR
0E
P1.6/SMISO P1.5/SMOSI
Reserved
Reserved
Int Enable
P2.1–P2.0
------bb
00000000
Int Act Low
TTL Thresh
High Sink
Open Drain
Pull up
Enable
Output
Enable
bbbbbbbb
00000000
Int Act Low
TTL Thresh
Reserved
Open Drain
Pull up
Enable
Output
Enable
--bb-bbb
00000000
Int Enable
Int Act Low
TTL Thresh
Reserved
Open Drain
Pull up
Enable
Output
Enable
-bbb-bbb
00000000
Reserved
Int Enable
Int Act Low
5K pullup
Enable
Output
enable
bbb----b
00000000
P11CR
Reserved
Int Enable
Int Act Low
Open Drain
Reserved
Output
Enable
-bb--b-b
00000000
0F
P12CR
CLK Output
Int Enable
Int Act Low
TTL
Threshold
Reserved
Open Drain
Pull up
Enable
Output
Enable
bbbb-bbb
00000000
10
P13CR
Reserved
Int Enable
Int Act Low
Reserved
High Sink
Open Drain
Pull up
Enable
Output
Enable
-bb-bbbb
00000000
11–13
P14CR–
P16CR
SPI Use
Int Enable
Int Act Low
Reserved
High Sink
Open Drain
Pull up
Enable
Output
Enable
bbb-bbbb
00000000
14
P17CR
Reserved
Int Enable
Int Act Low
Reserved
High Sink
Open Drain
Pull up
Enable
Output
Enable
-bb-bbbb
00000000
15
P2CR
Reserved
Int Enable
Int Act Low
TTL Thresh
High Sink
Open Drain
Pull up
Enable
Output
Enable
-bbbbbbb
00000000
Reserved
Reserved
Reserved
20
FRTMRL
Free Running Timer [7:0]
bbbbbbbb
00000000
21
FRTMRH
Free Running Timer [15:8]
bbbbbbbb
00000000
rrrrrrrr
00000000
26
PITMRL
27
PITMRH
28
PIRL
29
PIRH
30
CPUCLKCR
31
TMRCLKCR
34
IOSCTR
36
LPOSCTR
3C
SPIDATA
3D
SPICR
Prog Interval Timer [7:0]
Reserved
Prog Interval Timer [11:8]
Prog Interval [7:0]
Reserved
Prog Interval [11:8]
Reserved
TCAPCLK Divider
TCAPCLK Select
ITMRCLK Divider
foffset[2:0]
ITMRCLK Select
Gain[4:0]
32 kHz Low
Power
Reserved
32 kHz Bias Trim [1:0]
Swap
LSB First
Comm Mode
32 kHz Freq Trim [3:0]
SPIData[7:0]
DA
INT_CLR0 GPIO Port 1
Sleep Timer
INT1
DB
INT_CLR1
Reserved
Prog Interval
Timer
1 ms Timer
DC
INT_CLR2
Reserved
Reserved
Reserved
Document Number: 001-07611 Rev *I
GPIO Port 0
CPOL
CPHA
SPI Receive
SPI Transmit
SCLK Select
Reserved
POR/LVD
Reserved
GPIO Port 2
Reserved
INT2
16-bit
Counter
Wrap
Reserved
----rrrr
00000000
bbbbbbbb
00000000
----rrrr
00000000
--------
00000000
bbbbbbbb
10001111
bbbbbbbb
000ddddd
0-bbbbbb
d-dddddd
bbbbbbbb
00000000
bbbbbbbb
00000000
bbbbbb-b
00000000
-bb-----
00000000
---b-bb-
00000000
Page 56 of 72
CYRF69103
Microcontroller Function Register Summary (continued)
Addr
Name
7
DE
INT_MSK3
ENSWINT
6
DF
INT_MSK2
Reserved
E0
E1
5
4
3
2
1
0
Reserved
R/W
Default
r-------
00000000
Reserved
Reserved
GPIO Port 2
Int Enable
Reserved
INT2
Int Enable
16-bit
Counter
Wrap Int
Enable
Reserved
---b-bb-
00000000
INT_MSK0 GPIO Port 1
Int Enable
Sleep Timer
Int Enable
INT1
Int Enable
GPIO Port 0
Int Enable
SPI Receive
Int Enable
SPI Transmit
Int Enable
Reserved
POR/LVD
Int Enable
bbbbbb-b
00000000
INT_MSK1
Prog Interval
Timer
Int Enable
1 ms Timer
Int Enable
-bb-----
00000000
Reserved
Reserved
E2
INT_VC
Pending Interrupt [7:0]
bbbbbbbb
00000000
E3
RESWDT
Reset Watchdog Timer [7:0]
wwwwwww
w
00000000
--
CPU_A
Temporary Register T1 [7:0]
--------
00000000
--
CPU_X
X[7:0]
--------
00000000
--
CPU_PCL
Program Counter [7:0]
--------
00000000
--
CPU_PCH
Program Counter [15:8]
--------
00000000
--
CPU_SP
F7
CPU_F
Stack Pointer [7:0]
FF
CPU_SCR
1E0
OSC_CR0
Reserved
1E3
LVDCR
Reserved
1E4
VLTCMP
1EB
ECO_TR
Reserved
GIES
Reserved
WDRS
No Buzz
XIO
Super
Carry
PORS
Sleep
Reserved
Sleep Timer [1:0]
PORLEV[1:0]
Document Number: 001-07611 Rev *I
Global IE
Reserved
Stop
CPU Speed [2:0]
Reserved
Reserved
Sleep Duty Cycle [1:0]
Zero
VM[2:0]
LVD
Reserved
PPOR
--------
00000000
---brbbb
00000010
r-ccb--b
00010100
--bbbbbb
00001000
--bb-bbb
00000000
------rr
00000000
bb------
00000000
Page 57 of 72
CYRF69103
Radio Function Register Summary
Address
0x00
0x01
Mnemonic
CHANNEL_ADR
TX_LENGTH_ADR
b7
Not Used
b6
0x02
TX_CTRL_ADR
TX GO
TX CLR
0x03
TX_CFG_ADR
Not Used
OS
IRQ
Not Used
LV
IRQ
RX GO
RSVD
0x04
TX_IRQ_STATUS_ADR
0x05
0x06
RX_CTRL_ADR
0x07
0x08
0x09
0x0A
0x0B
RX_IRQ_STATUS_ADR
RX_STATUS_ADR
RX_COUNT_ADR
RX_LENGTH_ADR
PWR_CTRL_ADR
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
RX_CFG_ADR
XTAL_CTRL_ADR
IO_CFG_ADR
GPIO_CTRL_ADR
XACT_CFG_ADR
FRAMING_CFG_ADR
DATA32_THOLD_ADR
DATA64_THOLD_ADR
RSSI_ADR
EOP_CTRL_ADR [9.]
CRC_SEED_LSB_ADR
CRC_SEED_MSB_ADR
TX_CRC_LSB_ADR
TX_CRC_MSB_ADR
RX_CRC_LSB_ADR
RX_CRC_MSB_ADR
TX_OFFSET_LSB_ADR
TX_OFFSET_MSB_ADR
MODE_OVERRIDE_ADR
b5
TXB15
IRQEN
DATA CODE
LENGTH
TXB15
IRQ
RXB16
IRQEN
AGC EN
RXOW
IRQ
RX ACK
LNA
SOPDET
IRQ
PKT ERR
ATT
RXB16
IRQ
EOP ERR
PMU EN
LVIRQ EN
PMU Mode
Force
XOUT FN
IRQ OD
IRQ POL
XOUT OP
MISO OP
ACK EN
Not Used
SOP EN
SOP LEN
Not Used
Not Used
Not Used
Not Used
SOP
Not Used
HEN
XSIRQ EN
MISO OD
PACTL OP
FRC END
LEN EN
Not Used
Not Used
LNA
HINT
Not Used
RSVD
Not Used
RSVD
Not Used
FRC SEN
0x1E
RX_OVERRIDE_ADR
ACK RX
RXTX DLY
MAN RXACK
0x1F
0x26
TX_OVERRIDE_ADR
XTAL_CFG_ADR
ACK TX
RSVD
FRC PRE
RSVD
RSVD
RSVD
b4
b3
Channel
TX Length
TXB8
TXB0
IRQEN
IRQEN
b2
b1
b0
TXBERR
IRQEN
TXC
IRQEN
TXE
IRQEN
PA SETTING
TXC
IRQ
RXC
IRQEN
TXE
IRQ
RXE
IRQEN
DATA MODE
TXB8
TXB0
TXBERR
IRQ
IRQ
IRQ
RXB8
RXB1
RXBERR
IRQEN
IRQEN
IRQEN
FAST TURN
HILO
EN
Not Used
RXB8
RXB1
RXBERR
IRQ
IRQ
IRQ
CRC0
Bad CRC
RX Code
RX Count
RX Length
LVI TH
PFET
disable
RXOW EN
VLD EN
RXC
RXE
IRQ
IRQ
RX Data Mode
PMU OUTV
Default[4]
-1001000
00000000
00000011
Access[4]
-bbbbbbb
bbbbbbbb
bbbbbbbb
--000101
--bbbbbb
--------
rrrrrrrr
00000111
bbbbbbbb
10010-10
bbbbb-bb
--------
brrrrrrr
-------00000000
00000000
10100000
rrrrrrrr
rrrrrrrr
rrrrrrrr
bbb-bbbb
000--100
00000000
0000---1-000000
10100101
----0100
---01010
0-100000
10100100
00000000
00000000
--------------11111111
11111111
00000000
----0000
00000--0
0000000-
bbb--bbb
bbbbbbbb
bbbbrrrr
b-bbbbbb
bbbbbbbb
----bbbb
---bbbbb
r-rrrrrr
bbbbbbbb
bbbbbbbb
bbbbbbbb
rrrrrrrr
rrrrrrrr
rrrrrrrr
rrrrrrrr
bbbbbbbb
----bbbb
wwwww--w
bbbbbbb-
[10.]
Not Used
XOUT OD
IRQ OP
Not Used
FREQ
PACTL OD PACTL GPIO
SPI 3PIN
IRQ GPIO
XOUT IP
MISO IP
PACTL IP
IRQ IP
END STATE
ACK TO
SOP TH
Not Used
TH32
TH64
RSSI
EOP
CRC SEED LSB
CRC SEED MSB
CRC LSB
CRC MSB
CRC LSB
CRC MSB
STRIM LSB
Not Used
STRIM MSB
FRC AWAKE
Not Used
Not Used
RST
FRC
RXDR
DIS CRC0 DIS RXCRC
ACE
Not Used
MAN
TXACK
OVRD ACK DIS TXCRC
RSVD
TX INV
RSVD
START DLY
RSVD
RSVD
RSVD
00000000
bbbbbbbb
00000000
wwwwwww
w
wwwwwww
w
wwwwwww
w
wwwwwww
w
wwwwwww
w
wwwwwww
w
wwwwwww
w
0x27
CLK_OVERRIDE_ADR
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
RXF
RSVD
00000000
0x28
CLK_EN_ADR
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
RXF
RSVD
00000000
0x29
RX_ABORT_ADR
RSVD
RSVD
ABORT EN
RSVD
RSVD
RSVD
RSVD
RSVD
00000000
0x32
AUTO_CAL_TIME_ADR
0x35
AUTO_CAL_OFFSET_ADR
0x39
ANALOG_CTRL_ADR
AUTO_CAL_TIME
00000011
AUTO_CAL_OFFSET
RSVD
RSVD
RSVD
RSVD
RSVD
00000000
RSVD
RX INV
ALL SLOW
00000000
Register Files
0x20
TX_BUFFER_ADR
TX Buffer File
--------
0x21
0x22
0x23
0x24
0x25
RX Buffer File
SOP Code File
Data Code File
Preamble File
MFG ID File
-------Note [5]
Note [6]
Note [7]
NA
RX_BUFFER_ADR
SOP_CODE_ADR
DATA_CODE_ADR
PREAMBLE_ADR
MFG_ID_ADR
wwwwwww
w
rrrrrrrr
bbbbbbbb
bbbbbbbb
bbbbbbbb
rrrrrrrr
All registers are read and writable, except where noted. Registers may be written to or read from either individually or in sequential
groups. A single-byte read or write reads or writes from the addressed register. Incrementing burst read and write is a sequence that
begins with an address, and then reads or writes to/from each register in address order for as long as clocking continues. It is possible
to repeatedly read (poll) a single register using a nonincrementing burst read.
Notes
4. b = read/write; r = read only; w = write only; ‘-’ = not used, default value is undefined.
5. SOP_CODE_ADR default = 0x17FF9E213690C782.
6. DATA_CODE_ADR default = 0x02F9939702FA5CE3012BF1DB0132BE6F.
7. PREAMBLE_ADR default = 0x333302;The count value must be great than 4 for DDR and greater than 8 for SDR
8. Registers must be configured or accessed only when the radio is in IDLE or SLEEP mode.The PMU, GPIOs, RSSI registers can be accessed in Active Tx and Rx
mode.
9. EOP_CTRL_ADR[6:4] must never have the value of “000” i.e. EOP Hint Symbol count must never be “0”
Document Number: 001-07611 Rev *I
Page 58 of 72
CYRF69103
DC Voltage to Logic Inputs [11] ............ –0.3 V to VIO + 0.3 V
Absolute Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage Temperature ................................. –40 °C to +90 °C
Ambient Temperature with Power Applied ..... 0 °C to +70 °C
Supply Voltage on any power supply pin
relative to VSS ..............................................–0.3 V to +3.9 V
DC Voltage applied to Outputs
in High Z State ..................................... –0.3 V to VIO + 0.3 V
Static Discharge Voltage (Digital) [12] ...................... >2000 V
Static Discharge Voltage (RF) [12] .............................. 1100 V
Latch up Current .....................................+200 mA, –200 mA
Ground Voltage ................................................................ 0 V
FOSC (Crystal Frequency) .......................... 12 MHz ±30 ppm
DC Characteristics
(T = 25 C)
Parameter
Description
Conditions
Min
Typ
Max
Unit
VBAT
Battery Voltage
0–70 C
1.8
–
3.6
V
VREG[13]
PMU Output Voltage
2.7V mode
2.7
2.73
–
V
VLVD
Low Voltage Detect
LVDCR [2:0] set to 000
2.69
2.7
2.72
V
LVDCR [2:0] set to 001
2.90
2.92
2.94
V
LVDCR [2:0] set to 010
3.00
3.02
3.04
V
LVDCR [2:0] set to 011
3.10
3.13
3.15
V
1.8
–
3.6
V
2.4
–
3.6
V
VIO
VIO Voltage
VCC
VCC Voltage
0–70 C
Device Current (For total current consumption in different modes, for example Radio, active, MCU, and sleep, add Radio Function
Current and MCU Function Current)
PA = 5, 2-way, 4 bytes/10 ms CPU
speed = 6 MHz
–
9.87
–
mA
ICC (32-8DR)[14] Average ICC, 250 kbps, fast channel
PA = 5, 2-way, 4 bytes/10 ms CPU
speed = 6 MHz
–
10.2
–
mA
ISB1
Sleep Mode ICC
VCC = 3.0V, MCU sleep, PMU
disabled
–
2.72
–
µA
ISB2
Sleep Mode ICC
VCC = 3.0V, MCU sleep, PMU enabled
–
30.4
–
µA
ICC (GFSK)[14]
Average ICC, 1 Mbps, slow channel
Notes
11. It is permissible to connect voltages above VIO to inputs through a series resistor limiting input current to 1 mA. AC timing not guaranteed.
12. Human Body Model (HBM).
13. VREG depends on battery input voltage.
14. Includes current drawn while starting crystal, starting synthesizer, transmitting packet (including SOP and CRC16), changing to receive mode, and receiving ACK
handshake. Device is in sleep except during this transaction.
Document Number: 001-07611 Rev *I
Page 59 of 72
CYRF69103
DC Characteristics (continued)
(T = 25 C)
Parameter
Description
Conditions
Min
Typ
Max
Unit
–
1.1
–
mA
Radio Function Currents (VCC = 3.0 V, MCU Sleep)
IDLE ICC
Radio off, XTAL Active
XOUT disabled
Isynth
ICC during Synth Start
–
8.6
–
mA
TX ICC
ICC during Transmit
PA = 5 (–5 dBm)
–
21.2
–
mA
TX ICC
ICC during Transmit
PA = 6 (0 dBm)
–
28.5
–
mA
TX ICC
ICC during Transmit
PA = 7 (+4 dBm)
–
39.9
–
mA
RX ICC
ICC during Receive
LNA off, ATT on.
–
18.9
–
mA
RX ICC
ICC during Receive
LNA on, ATT off.
–
21.9
–
mA
Boost Eff
PMU Boost Converter Efficiency
VBAT = 2.5V,
VREG = 2.73V, ILOAD = 20 mA
–
83
–
%
ILOAD_EXT[15]
Average PMU External Load current
VBAT = 1.8V,
VREG = 2.73V, RX Mode
–
–
15
mA
MCU Function Currents (VDD = 3.0V)
IDD1
VDD Operating Supply Current
CPU speed = 6 MHz
–
5.0
–
mA
IDD1
VDD Operating Supply Current
CPU speed = 3 MHz
–
4.4
–
mA
Radio Function GPIO Interface
VOH1
Output High Voltage Condition 1
At IOH = –100.0 µA
VIO – 0.1
VIO
–
V
VOH2
Output High Voltage Condition 2
At IOH = –2.0 mA
VIO – 0.4
VIO
–
V
VOL
Output Low Voltage
At IOL = 2.0 mA
–
0
0.4
V
VIH
Input High Voltage
0.76VIO
–
VIO
V
VIL
Input Low Voltage
0
–
0.24VIO
V
IIL
Input Leakage Current
0 < VIN < VIO
–1
0.26
+1
µA
CIN
Pin Input Capacitance
except XTAL, RFN, RFP, RFBIAS
–
3.5
10
pF
MCU Function GPIO Interface
RUP
Pull up Resistance
4
–
12
K
VICR
Input Threshold Voltage Low, CMOS
mode
Low to High edge
40%
–
65%
VCC
VICF
Input Threshold Voltage Low, CMOS
mode
High to Low edge
30%
–
55%
VCC
VHC
Input Hysteresis Voltage, CMOS Mode
High to low edge
3%
–
10%
VCC
VILTTL
Input Low Voltage, TTL Mode
VIHTTL
Input HIGH Voltage, TTL Mode
VOL1
Output Low Voltage, High Drive[16]
VOL2
Output Low Voltage, High
Drive[16]
VOL3
Output Low Voltage, Low Drive
VOH
Output High
Voltage[17]
–
–
0.72
V
1.6
–
–
V
IOL1 = 50 mA
–
–
1.4
V
IOL1 = 25 mA
–
–
0.4
V
IOL2 = 8 mA
–
–
0.8
V
IOH = 2 mA
VCC – 0.5
–
–
V
Notes
15. ILOAD_EXT is dependant on external components and this entry applies when the components connected to L/D are SS12 series diode and DH53100LC inductor from
Sumida.
16. Available only on P1.3,P1.4,P1.5,P1.6,P1.7.
17. Except for pins P1.0, P1,1 in GPIO mode.
Document Number: 001-07611 Rev *I
Page 60 of 72
CYRF69103
AC Characteristics
Parameter
Description
Conditions
Min
Typ
Max
Unit
GPIO Timing
TR_GPIO
Output Rise Time
Measured between 10 and 90%
Vdd/Vreg with 50 pF load
–
–
50
ns
TF_GPIO
Output Fall Time
Measured between 10 and 90%
Vdd/Vreg with 50 pF load
–
–
15
ns
FIMO
Internal Main Oscillator Frequency
With proper trim values loaded[5]
18.72
–
26.4
MHz
FILO
Internal Low Power Oscillator
With proper trim values loaded[5]
15.0001
–
50.0
kHz
TSMCK
SPI Master Clock Rate
FCPUCLK/6
–
–
2
MHz
TSSCK
SPI Slave Clock Rate
–
–
2.2
MHz
TSCKH
SPI Clock High Time
High for CPOL = 0, Low for CPOL = 1
125
–
–
ns
TSCKL
SPI Clock Low Time
Low for CPOL = 0, High for CPOL = 1
125
–
–
ns
TMDO
Master Data Output Time[18]
SCK to data valid
–25
–
50
ns
TMDO1
Master Data Output Time,
First bit with CPHA = 0
Time before leading SCK edge
100
–
–
ns
SPI Timing
TMSU
Master Input Data Setup time
50
–
–
ns
TMHD
Master Input Data Hold time
50
–
–
ns
TSSU
Slave Input Data Setup Time
50
–
–
ns
TSHD
Slave Input Data Hold Time
50
–
–
ns
TSDO
Slave Data Output Time
SCK to data valid
–
–
100
ns
TSDO1
Slave Data Output Time,
First bit with CPHA = 0
Time after SS LOW to data valid
–
–
100
ns
TSSS
Slave Select Setup Time
Before first SCK edge
150
–
–
ns
TSSH
Slave Select Hold Time
After last SCK edge
150
–
–
ns
Figure 19. Clock Timing
TCYC
TCH
CLOCK
TCL
Note
18. In Master mode first bit is available 0.5 SPICLK cycle before Master clock edge available on the SCLK pin.
Document Number: 001-07611 Rev *I
Page 61 of 72
CYRF69103
Figure 20. GPIO Timing Diagram
90%
GPIO Pin Output
Voltage
10%
TR_GPIO
TF_GPIO
Figure 21. SPI Master Timing, CPHA = 1
SS
(SS is under firmware control in SPI Master mode)
TSCKL
SCK (CPOL=0)
TSCKH
SCK (CPOL=1)
TMDO
MOSI
MISO
MSB
MSB
LSB
LSB
TMSU TMHD
Document Number: 001-07611 Rev *I
Page 62 of 72
CYRF69103
Figure 22. SPI Slave Timing, CPHA = 1
SS
TSSS
TSSH
TSCKL
SCK (CPOL=0)
TSCKH
SCK (CPOL=1)
MOSI
MSB
LSB
TSSU TSHD
TSDO
MSB
MISO
LSB
Figure 23. SPI Master Timing, CPHA = 0
SS
(SS is under firmware control in SPI Master mode)
TSCKL
SCK (CPOL=0)
TSCKH
SCK (CPOL=1)
TMDO
TMDO1
MOSI
MISO
MSB
MSB
LSB
LSB
TMSU TMHD
Document Number: 001-07611 Rev *I
Page 63 of 72
CYRF69103
Figure 24. SPI Slave Timing, CPHA = 0
SS
TSSH
TSSS
TSCKL
SCK (CPOL=0)
TSCKH
SCK (CPOL=1)
MSB
MOSI
LSB
TSSU TSHD
TSDO1
MISO
MSB
Document Number: 001-07611 Rev *I
TSDO
LSB
Page 64 of 72
CYRF69103
RF Characteristics
Table 77. Radio Parameters
Parameter Description
Conditions
RF Frequency Range
Subject to regulation
Receiver (T = 25 °C, VCC = 3.0 V, fOSC = 12.000 MHz, BER < 10–3)
Sensitivity 125 kbps 64-8DR
BER 1E-3
Min
Typ
Max
Unit
2.400
–
2.497
GHz
–
–97
–
dBm
Sensitivity 250 kbps 32-8DR
BER 1E-3
–
–93
–
dBm
Sensitivity
CER 1E-3
–80
–87
–
dBm
Sensitivity GFSK
BER 1E-3, ALL SLOW = 1
LNA Gain
ATT Gain
–
–84
–
dBm
–
22.8
–
dB
–
–31.7
–
dB
Maximum Received Signal
LNA On
–15
–6
–
dBm
RSSI Value for PWRin –60 dBm [19]
LNA On
–
21
–
Count
–
1.9
–
dB/Count
RSSI Slope
Interference Performance (CER 1E-3)
Co-channel Interference rejection
Carrier-to-Interference (C/I)
C = –60 dBm,
–
9
–
dB
Adjacent (±1 MHz) Channel Selectivity C/I 1 MHz
C = –60 dBm
–
3
–
dB
Adjacent (±2 MHz) Channel Selectivity C/I 2 MHz
C = –60 dBm
–
–30
–
dB
Adjacent (> 3 MHz) Channel Selectivity C/I > 3 MHz C = –67 dBm
–
–38
–
dB
Out-of-Band Blocking 30 MHz–12.75 MHz[20]
C = –67 dBm
–
–30
–
dBm
Intermodulation
C = –64 dBm, f = 5,10 MHz
–
–36
–
dBm
800 MHz
100 kHz ResBW
–
–79
–
dBm
1.6 GHz
100 kHz ResBW
–
–71
–
dBm
3.2 GHz
100 kHz ResBW
–
–65
–
dBm
Maximum RF Transmit Power
PA = 7
+2
4
+6
dBm
Maximum RF Transmit Power
PA = 6
–2
0
+2
dBm
Maximum RF Transmit Power
PA = 5
–7
–5
–3
dBm
Maximum RF Transmit Power
PA = 0
–
–35
–
dBm
–
39
–
dB
Receive Spurious Emission
Transmitter (T = 25°C, VCC = 3.0V, fOSC = 12.000 MHz)
RF Power Control Range
RF Power Range Control Step Size
seven steps, monotonic
–
5.6
–
dB
Frequency Deviation Min
PN Code Pattern 10101010
–
270
–
kHz
Frequency Deviation Max
PN Code Pattern 11110000
–
323
–
kHz
Error Vector Magnitude (FSK error)
>0 dBm
–
10
–
%rms
Occupied Bandwidth
–6 dBc, 100 kHz ResBW
500
876
–
kHz
Notes
19. RSSI value is not guaranteed. Extensive variation from part to part.
20. Exceptions F/3 & 5C/3.
Document Number: 001-07611 Rev *I
Page 65 of 72
CYRF69103
Table 77. Radio Parameters (continued)
Parameter Description
Conditions
Min
Typ
Max
Unit
–
–38
–
dBm
Transmit Spurious Emission (PA = 7)
In-band Spurious Second Channel Power (±2 MHz)
In-band Spurious Third Channel Power (>3 MHz)
–
–44
–
dBm
Non-Harmonically Related Spurs (8.000 GHz)
–
–38
–
dBm
Non-Harmonically Related Spurs (1.6 GHz)
–
–34
–
dBm
Non-Harmonically Related Spurs (3.2 GHz)
–
–47
–
dBm
Harmonic Spurs (Second Harmonic)
–
–43
–
dBm
Harmonic Spurs (Third Harmonic)
–
–48
–
dBm
Fourth and Greater Harmonics
–
–59
–
dBm
Power Management (Crystal PN# eCERA GF-1200008)
Crystal Start to 10ppm
–
0.7
1.3
ms
Crystal Start to IRQ
XSIRQ EN = 1
–
0.6
–
ms
Synth Settle
Slow channels
–
–
270
µs
Synth Settle
Medium channels
–
–
180
µs
Synth Settle
Fast channels
–
–
100
µs
Link Turnaround Time
GFSK
–
–
30
µs
Link Turnaround Time
250 kbps
–
–
62
µs
Link Turnaround Time
125 kbps
–
–
94
µs
Link Turnaround Time
<125 kbps
–
–
31
µs
Max. packet length
< 60 ppm crystal-to-crystal
all modes except 64-DDR
and 64-SDR
–
–
40
bytes
Max. packet length
< 60 ppm crystal-to-crystal
64-DDR and 64-SDR
–
–
16
bytes
Document Number: 001-07611 Rev *I
Page 66 of 72
CYRF69103
Ordering Information
Package
Ordering Part Number
Status
40-pin Pb-Free QFN 6 × 6 mm (Sawn)
CYRF69103-40LTXC
In Production
40-pin Pb-free QFN 6 × 6 mm (Punch)
CYRF69103-40LFXC
NRND
Ordering Code Definitions
CY RF 69103 - 40
LX
X
C
Temperature Range:
C = Commercial
Pb-free
Package Type: LX = LF or LT
LF = QFN (Punch Type); LT = QFN (Sawn Type)
No of pins in package: 40-pin
Part Number
Marketing Code: RF = Wireless (radio frequency) product line
Company ID: CY = Cypress
Document Number: 001-07611 Rev *I
Page 67 of 72
CYRF69103
Package Handling
Some IC packages require baking before they are soldered onto a PCB to remove moisture that may have been absorbed after leaving
the factory. A label on the packaging has details about actual bake temperature and the minimum bake time to remove this
moisture.The maximum bake time is the aggregate time that the parts are exposed to the bake temperature. Exceeding this exposure
time may degrade device reliability.
Table 78. Package Handling
Parameter
Description
TBAKETEMP
Bake Temperature
TBAKETIME
Bake Time
Min
see package label
Typ
Max
Unit
125
see package label
°C
72
hours
Package Diagram
Figure 25. 40-pin QFN (6 × 6 × 1.0 mm) LT40B 3.50 × 3.50 E-Pad (Sawn) Package Outline, 001-13190
001-13190 *H
Document Number: 001-07611 Rev *I
Page 68 of 72
CYRF69103
Figure 26. 40-pin QFN (6 × 6 × 1.0 mm) LF40A/LY40A (3.50 × 3.50 mm) E-Pad (Punch) Package Outline, 001-12917 [21]
SOLDERABLE
EXPOSED
PAD
001-12917 *C
Note
21. Not Recommended for New Design.
Document Number: 001-07611 Rev *I
Page 69 of 72
CYRF69103
Acronyms
Document Conventions
Table 79. Acronyms Used in this Document
Units of Measure
Acronym
Description
Table 80. Units of Measure
ACK
Acknowledge (packet received, no errors)
AGC
Automatic Gain Control
°C
degree Celsius
ATS
Auto Transaction Sequencer
dB
decibel
CMOS
Complementary Metal Oxide Semiconductor
dBm
decibel-milliwatt
CPU
Central Processing Unit
GHz
gigahertz
EEPROM
Electrically Erasable Programmable Read-Only
Memory
Hz
hertz
kHz
kilohertz
GFSK
Gaussian Frequency-Shift Keying
k
kilohm
GPIO
General Purpose Input/Output
MHz
megahertz
HID
Human Interface Devices
F
microfarad
I/O
Input/Output
s
microsecond
ISM
Industrial, Scientific, and Medical
W
microwatt
LNA
Low Noise Amplifier
mA
milliampere
MCU
Microcontroller Unit
mm
millimeter
MOSI
Master Out Slave In
ms
millisecond
PMU
Power Management Unit
mV
millivolt
PSoC
Programmable System-on-Chip
ns
nanosecond
QFN
Quad Flat No-lead

ohm
RAM
Random Access Memory
%
percent
ppm
parts per million
RSSI
Received Signal Strength Indication
pF
picofarad
SCK
Serial Clock
V
volt
SPI
Serial Peripheral Interface
SROM
Supervisory Read Only Memory
SS
Slave Select
TTL
Transistor-Transistor Logic
Document Number: 001-07611 Rev *I
Symbol
Unit of Measure
Page 70 of 72
CYRF69103
Document History Page
Document Title: CYRF69103, Programmable Radio on Chip Low Power
Document #: 001-07611
Rev.
ECN No.
Orig. of
Change
Submission
Date
See ECN
New advance data sheet.
See ECN
Preliminary data sheet.
Created Preliminary data sheet from Advance Information.
Description of Change
**
479801
OYR
*A
501282
OYR
*B
631696
BOO
*C
2447906
AESA
See ECN
*D
2615458
KKU /
AESA
01/13/2009
Replaced 51-85190 with 001-12917. Fixed format and language inconsistencies.
*E
2761532
DVJA
09/09/2009
Changed default value of the Sleep Timer from 00(512 Hz) to 01(64 Hz) in the
OSC_CR0 [0x1E0] register.
*F
2885149
KKU
02/26/2010
Updated the following sections:
Microcontroller Function, Clock Architecture Description, CPU Clock During
Sleep Mode, Sleep Mode, Low Power in Sleep Mode, General Purpose I/O
Ports, Microcontroller Function Register Summary, and Package Diagram
*G
3552304
ANTG
03/15/2012
Added sub-section Receive Spurious Response under the main section
Functional Block Overview.
Updated RF Characteristics (Updated Table 77 (Added Note 19 and referred
the same note in the parameter ”RSSI Value for PWRin –60 dBm”)).
Added Ordering Code Definitions.
Updated Package Diagram (Added Figure 25).
Added Acronyms and Units of Measure.
*H
3717153
ANKC
08/21/2012
Updated Ordering Information (No change in part numbers, included a column
“Status”).
Updated Package Diagram (spec 001-13190 (Changed revision from *G to *H),
added Note 21 and referred the same note in Figure 26).
*I
3913209
ANKC
02/25/2013
Updated Pinouts (Updated Figure 1).
See ECN
Final data sheet. Updated DC Characteristics table with characterization data.
Minor text changes
GPIO capacitance and timing diagram included
Sleep and Wakeup sequence documented
PIT Timer registers’ R/W capability corrected to read only
Updated radio function register descriptions
Changed L/D pin description
Changed RST Capacitor from 0.1 uF to 0.47 uF
Added example PMU configuration circuits
Updated to new template
Updated Pin Definitions (Updated descriptions of Pin 21 and Pin 22).
Updated Functional Block Overview (Updated 2.4 GHz Radio (Replaced seven
steps with eight steps)).
Updated General Purpose I/O Ports (Updated GPIO Port Configuration
(Updated High Sink (Removed CY7C601xx, CY7C602xx related information),
updated SPI Use (Removed CY7C601xx, CY7C602xx related information))).
Document Number: 001-07611 Rev *I
Page 71 of 72
CYRF69103
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
cypress.com/go/memory
Optical & Image Sensing
cypress.com/go/image
PSoC
cypress.com/go/psoc
Touch Sensing
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2006-2013. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-07611 Rev *I
Revised February 25, 2013
Page 72 of 72
WirelessUSB, PSoC, enCoRe and PRoC are trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective
holders.