DEMO MANUAL DC1907A isoSPI 2-Wire Serial Analyzer Description Demonstration circuit 1907A is an isoSPI™ analyzer board. isoSPI is a bi-direction 2-wire serial interface with high noise immunity and the ability to communicate over long cables. Because isoSPI is a proprietary serial interface with unique signaling, the DC1907 board is available to help users develop systems using the isoSPI serial link. The DC1907 can be connected across the two wires of an isoSPI link to decode the isoSPI communication and convert the signals to standard 4-wire SPI. The DC1907 is also capable of displaying the isoSPI link data on a PC for analysis or troubleshooting. Design files for this circuit board are available at http://www.linear.com/demo L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and isoSPI is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Operation Description The DC1907 implements an isoSPI receiver that can connect across a 2-wire isoSPI data link. The DC1907 does not terminate the isoSPI lines and should represent a minimal load to an operating isoSPI serial link. The DC1907 decodes the isoSPI data using comparators to check for minus 1 and plus 1 signals and an FPGA to check pulse timing. After pulses have been decoded the FPGA outputs the serial data in a standard SPI format onto the logic analyzer header JP13 for analysis with an oscilloscope or logic analyzer. The FPGA also sends the detected isoSPI data to an onboard microcontroller(MCU) that formats the data and transmits it to a PC. The MCU connects to the PC over a USB link. Software is available that can decode the data sent from the DC1907 to the PC. The software is capable of displaying data and data logging. For LTC®6804 battery management applications the software is capable of decoding unique device commands and checking the command packet error codes(PEC) to aid program development. Performance Summary Specifications are at TA = 25°C SYMBOL PARAMETER CONDITIONS VS Supply Range ISUPPLY Supply Current 150 mA VLOGIC Logic Analyzer Voltage Output Level 3.3 V MIN TYP 4.5 MAX 5.5 UNITS V dc1907af 1 DEMO MANUAL DC1907A Board PHOTO POWER CONNECTIONS EXT/USB JUMPER LOGIC ANALYZER HEADER VTH JUMPERS LED INDICATORS USB isoSPI CONNECTIONS RESET BUTTON CONNECTION SUMMARY Turrets Logic Analyzer Header • VIN: Power supply input, 4.5V to 5.5V up to 200mA • MOSI: The decoded master out slave in signal • GND: Power supply ground connection • MISO: The decoded master in slave out signal IN+: Isolated IP turret. This turret connects to the IP • line of an isoSPI network • IN–: Isolated IM turret. This turret connects to the IM line of an isoSPI network • CS: The decoded chip select • SCK: The decoded clock signal Connections • Buff IN+: A buffered version of the isoSPI IP signal • J1 Power Jack • Buff IN–: A buffered version of the isoSPI IM signal • RJ45 IN • RJ45 OUT • USB dc1907af 2 DEMO MANUAL DC1907A Jumper Summary JP1 VIN - EXT/USB JP 2, 4, 6, 7 - VTH Jumpers • Ext: Set to EXT to power the board from an external 5V supply. Note that all four of these jumpers must be connected the same (i.e. connected to VTH1 or VTH2). • USB(default): Set to USB to power the board from a PC’s USB port (no external supply required). • VTH1: Use this setting for an isoSPI link with Ibias between 160µA and 1mA (default setting). • VTH2: Use this setting for an isoSPI link with Ibias between 100µA and 160µA. LED Summary ON: Indicates the state of the connection between the PC and the DC1907 MCU. If the LED is blinking, the MCU is waiting for the PC to connect. If the LED is solid this means the MCU is connected to the PC. TX: Indicates when data is being sent from the MCU to the PC. The LED turns on when the MCU is communicating with the PC. ER: Indicates a full transmit buffer. If this LED is ON the PC will most likely have lost some of the isoSPI transmitted data. Button Summary Reset: Can be used to reset the MCU. This button is useful if the MCU appears to be non responsive and data is not being received by the PC. Boot: This button is used to program the MCU. Do not use. Software Installation • Unzip isoSPI_Software.zip • Double click setup.exe and go through setup instructions • Software will install into a Start Menu → Programs folder called Linear Technology dc1907af 3 DEMO MANUAL DC1907A Driver Installation Windows XP • From the Start Menu, open the Control Panel. • Connect the DC1907 to a USB port and wait for new hardware installer to open. • In the Control Panel, navigate to System and Security. Then, click on System and in the System window open the Device Manager. • Do not allow windows to search for the driver automatically. Select the install from a list or specific location option, then navigate to the folder where the DC1907 software was installed. This will default to either C:\Program Files\LTC\DC1907_Generic or C:\Program Files\LTC\DC1907_LTC6804 depending on which version of the software was installed. If both versions are installed, the driver can be found in either location. • Windows should now find the DC1907.inf file and install the drivers. Windows 7/XP • Connect the DC1907 to a USB port and Windows will automatically begin it's driver installation process. It will fail after a short time. • Look under Ports (COM & LPT). There should be an open port named DC1907_isoSPI_Analyzer (COMxx) • Right click on the DC1907_isoSPI_Analyzer (COMxx) port and choose the Update Driver Software option. • Next, choose the Browse my computer for Driver software option. • Navigate to and select the DC1907's driver file, named DC1907.inf, located in the folder that the DC1907 software was installed into. This will default to either C:\Program Files(x86)\LTC\DC1907_Generic or C:\Program Files(x86)\LTC\DC1907_LTC6804 depending on which version of the software was installed. • Windows will finish up the driver installation from there. dc1907af 4 DEMO MANUAL DC1907A Hardware Connections 4-Wire SPI Decode Connection 2)Connect the DC1907 to a PC through a USB port. Figure 1 shows how to connect the DC1907 to two DC1941(LTC6820) isoSPI demo boards. 3)Connect both DC1941 J1 RJ45 connectors to the DC1907 with two CAT5 patch cables. 1)Set JP1 to USB if you want the DC1907 to be powered from the computer USB port. Make sure threshold jumpers are set to VTH1. Figure 1. isoSPI Demo Board Setup dc1907af 5 DEMO MANUAL DC1907A Hardware Connections Figure 2 shows how to connect the DC1907 to any isoSPI network. 2)Set JP1 to USB to have the board powered from the computer’s USB port. 1)The DC1907 must be connected on the cable side of the isoSPI network. Connect the IN+ turret to the isolated IP signal. Connect the IN– turret to the isolated IM signal. The IN+ → IP and IN– →IM connect can be made on test points, in the cable or even on the pads of the transformer. 3)Connect the DC1907 to the PC through a USB port. Figure 2. General isoSPI Connection Setup dc1907af 6 DEMO MANUAL DC1907A LTC6804 Software Operation The DC1907 isoSPI monitoring software is easy to use. When you open the software you will see the window shown in Figure 3. The software will automatically try to connect to the attached DC1907. Once the board connects, the status box will become green and indicate connected. The ON LED on the DC1907 should be blinking while the software is trying to connect. Once the software has connected, the LED will turn solid. If the board does not connect, make sure that the ON LED is blinking. If it is not blinking press the reset button located on the DC1907 demo board. Once the LED is blinking, manually select the comm. port in the software and click the connect button. Generally, if there is more than one port listed the DC1907 will most likely be the highest numbered port. The connection status is also indicated on the DC1907 board by the ON LED. Once the software has connected (Figure 4) it will begin to display data decoded by the DC1907. The software displays LTC6804 data separated into IC data and command data. The IC data is made up of the master out slave in (MOSI) row and the master in slave out (MISO) row. Data is displayed in hex format. The LTC6804 command data is decoded and the software will check to make sure the transmitted command PEC matches a calculated PEC. CONNECTION STATUS Figure 3. isoSPI Analyzer Start Screen Figure 4. dc1907af 7 DEMO MANUAL DC1907A LTC6804 Software Operation If desired, the decoded isoSPI hex data can be saved into a .csv file by clicking the Start Datalog button. A dialog box will open as is shown in Figure 5. A custom file name and save location can be entered along with notes to append to the data log. To start the datalog click the green Start Datalog button. When using the DC1907 with the LTC6804-2, the IC version should be changed from LTC6804-1 (default) to LTC6804-2. When the LTC6804-2 is selected, the display will reformat as shown in Figure 6. In this mode the software will read the address of each command and display it next to the data. Additional Software Controls • Pause/Resume: Pauses the screen from updating and can be used to pause the programs datalog. The software will continue to decode the isoSPI traffic in the background. • Clear: Clears the screen buffer and message counter. • Open Datalog: Opens the last completed datalog file in Windows Notepad to be viewed. • Close: Closes the program and disconnects the DC1907. • Close Port: Disconnects the DC1907 and stops data decode. Figure 5. Datalog Dialog IC VERSION SELECTED Figure 6. isoPSI Analyzer in LTC6804-2 Mode dc1907af 8 DEMO MANUAL DC1907A Generic Software Operation The Generic DC1907 isoSPI monitoring software can be used to monitor any isoSPI traffic. When you open the software you will see the window in Figure 7. The software will automatically try to connect to the attached DC1907. Once the board connects the status box will become green and indicate connected. The ON LED on the DC1907 should be blinking while the software is trying to connect. Once the software has connected the LED will turn solid. If the board does not connect, first make sure that the ON LED is blinking. If it is not blinking press the reset button located on the DC1907 demo board. Once the LED is blinking, manually select the com. port in the software and click the connect button. Generally if there is more than one port listed the DC1907 will most likely be the highest numbered port. The connection status is also indicated on the DC1907 board by the ON LED. CONNECTION STATUS Figure 7. Generic isoSPI Analyzer GUI dc1907af 9 DEMO MANUAL DC1907A Generic Software Operation Once the software has connected to the DC1907 it will begin to display data seen by the DC1907 shown in Figure 8. The software displays the master out slave in (MOSI) data and the master in slave out (MISO) data on separate lines and the data is displayed in hex format. By default the software displays data divided into bytes; this can be changed so that data is grouped into bytes, nibbles or 16 bit words. If desired, the decoded isoSPI hex data can be saved into a .csv file by clicking the Start Datalog button. A dialog will open, a custom file name and save location can be entered along with notes to append to the data log. To start the datalog, click the green Start Datalog button. Additional Software Controls • Pause/Resume: Pauses the screen from updating and can be used to pause the programs datalog. The software will continue to decode the isoSPI traffic in the background. • Clear: Clears the screen buffer and message counter. • Open Datalog: Opens the last completed datalog file in Windows Notepad to be viewed. • Close: Closes the program and disconnects the DC1907 • Close Port: Disconnects the DC1907 and stops data decode. Figure 8. dc1907af 10 DEMO MANUAL DC1907A Parts List ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER Required Circuit Components 1 21 C1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C13, C14, C15, C27, C28, C29, C30, C32, C33 CAP, 0.01µF 10% 25V X7R, 0603 AVX, 06033C103KAT 2 1 C23 CAP, 22µF 20%, 16V X7R,1210 AVX,1210YC226KAT2A 3 1 C24 CAP, 2.2µF 10% 16V X5R, 0603 TAIYO YUDEN, EMK107BJ225KA-T 4 2 C25, C57 CAP, 1µF 10% 16V X5R, 0603 AVX, 0603YD105KAT2A 5 2 C26, C35 CAP, 100pF 10% 25V X5R, 0603 AVX, 06033C101KAT2A 6 1 C31 CAP, 10µF 20%, 16V X7R,1210 AVX, 1210YC106KAT2A 7 2 C39, C40 CAP, 4.7µF 20% 16V X5R, 1206 TAIYO YUDEN, EMK316BJ475KL-T 8 9 C41, C43, C44, C45, C46 C49, C53, C55, C56 CAP, 0.1µF 20% 10V X5R, 0603 TAIYO YUDEN, LMK107BJ104MV-F 9 1 C42 CAP, 0.47µF 20% 16V X5R, 0603 AVX, 0603YD474KAT2A 10 0 C47, C48 OPT, 0603 11 2 C50, C54 CAP, 100nF 20% 25V X7R, 0603 AVX, 06033C104MAT2A 12 2 C51, C52 CAP, 20pF 10% 25V COG, 0603 AVX, 06033A220KAT2A 13 1 D1 SMALL SIGNAL SCHOTTKY DIODE, SOD-323 ST, BAT46JFILM 14 6 E1, E2, E3, E4, E5, E6 TESTPOINT, TURRET, 0.060" MILL-MAX, 2308-2-00-80-00-00-07-0 15 5 JP1, JP2, JP4, JP6, JP7 HEADER, 3PIN, 2MM SAMTEC TMM-103-02-L-S 16 5 XJP1 TO XJP7 SHUNT, 0.079" CENTER SAMTEC, 2SN-BK-G 17 4 JP5, JP9, JP12, JP13 HEADER, 6 PIN, 0.100" SAMTEC TSW-106-02-L-S 18 1 JP8 HEADER, 2X3 PIN, 0.100" SAMTEC TSW-103-02-L-D 19 1 J1 POWER JACK, KLDHCX-0202-AC KYCON, KLDHCX-0202-AC 20 DELETE BANANA JACKS 21 1 J4 CONNECTOR, USB TE CONNECTIVITY, 292304-2 22 2 J5, J6 CONNECTOR RJ45, CACE CODE 00779 TE CONNECTIVITY, 5406298-1-ND 23 3 LED1, LED2, LED3 RED1206 LED PANASONIC/LN1251C 24 2 R1, R8 RESISTOR, 300Ω 1% 0603 VISHAY, CRCW0603300RFKEA 25 2 R2, R6 RESISTOR, 100Ω 1% 0603 VISHAY, CRCW0603100RFKEA 26 2 R3, R7 RESISTOR, 150Ω 1% 0603 VISHAY, CRCW0603150RFKEA 27 1 R4 RESISTOR, 75Ω 1% 0603 VISHAY, CRCW060375R0FKEA 28 0 R5, R21, R22, R23, R24, R25, R35, R55 OPT, 0603 29 4 R9, R19, R26, R35 RESISTOR, 40.2kΩ 1% 0603 VISHAY, CRCW060340K2FKEA 30 5 R10, R20, R27, R32, R48 RESISTOR, 10kΩ 1% 0603 VISHAY, CRCW060310K0FKEA 31 2 R11, R13 RESISTOR, 4.7kΩ 1% 0603 VISHAY, CRCW06034K70FKEA 32 3 R12, R45, R49 RESISTOR, 330Ω 1% 0603 VISHAY, CRCW0603330RFKEA 33 3 R14, R16, R18 RESISTOR, 56Ω 1% 0603 VISHAY, CRCW060356R0FKEA 34 4 R15, R17, R28, R30 RESISTOR, 402Ω 1% 0603 VISHAY, CRCW0603402RFKEA 35 4 R29, R31, R33, R54 RESISTOR, 0Ω 1% 0603 VISHAY, CRCW06030000Z0EA dc1907af 11 DEMO MANUAL DC1907A Parts List ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER 36 0 R34, R36, R37, R38, R39, R40, R41, R43 OPT 37 1 R42 RESISTOR, 33kΩ 1% 0603 VISHAY, CRCW060333K0FKEA 38 3 R44, R46, R47 RESISTOR, 470Ω 1% 0603 VISHAY, CRCW0603470RFKEA 39 2 R50, R51 RESISTOR, 22Ω 1% 0603 VISHAY, CRCW060322R0FKEA 40 3 R56, R57, R58 RESISTOR, 1kΩ 1% 0603 VISHAY, CRCW06031K00FKEA 41 2 SW1, SW2 SWITCH, PUSH BUTTON PANASONIC/EVQPPDA25 42 1 T1 TRANSFORMER, HX1188NL PULSE, HX1188NL 43 2 U1, U2 IC, LT1719CS8 LINEAR TECHNOLOGY, LT1719CS8 44 1 U3 IC, LT1118 LINEAR TECHNOLOGY, LT1118 45 1 U4 IC, LT3021 LINEAR TECHNOLOGY, LT3021 46 1 U5 IC, LT1085 LINEAR TECHNOLOGY, LT1085 47 1 U6 IC, XCF02SVOG20C XILINX, XCF02SVOG20C 48 1 U7 IC, LT1819IMS8 LINEAR TECHNOLOGY, LT1819IMS8 49 1 U8 IC, XC3S50-5VQG100C XILINX, XC3S50-5VQG100C 50 0 U10 20MHZ-OSC, OPT 51 0 U11 CRISTAL OSCILL, OPT 52 1 U12 CRISTAL, 100MHz 4-SMB DFN,LCC CTS-FREQUENCY CONTROLS, CB3LV-3I-100M0000 53 1 U13 8-BIT MICROCONTROLLER, TQFP64 ATMEL, AT90USB646-AU, PACKAGE MD 54 1 U14 PRTR5V0U4D, SOT457-TSOP6 NXP SEMI, PRTR5V0U4D 55 2 U15, U16 BUFFER WITH OPEN-DRAIN OUTPUTS, SOT363 NXP SEMI, 74LVC2G07GW 56 1 X1 QUARTZ CRYSTAL ECS INC, ECS-160-20-4-DN 57 4 MH1 TO MH4 STAND-OFF, NYLON 0.5" TALL KEYSTONE, 8833(SNAP ON) dc1907af 12 A B C D IN- GND BUFF.IN- J6 RJ45 IN J5 RJ45 OUT IN+ BUFF.IN+ GND 5V 3 VCC OUT EG-2101 GND OE 3 2 9 4 5 6 5 3.3V R6 100 1 2 3 6 3.3V 6 5 C44 0.1uF 400 R30 R35 DNS 400 R28 R26 DNS 3.3V 2 + 3 - 3.3V 2 + 3 - VOUT_N 4 1. ALL CAPACITORS AND RESISTORS ARE 0603. U2 LT1719CS8 7 C45 0.1uF SCK CS VOUT_P C41 0.1uF C35 100pF U1 LT1719CS8 7 R7 150 R8 300 C25 1uF C40 4.7uF 1206 1 C26 100pF 3.3V 4 2 3 1.2V OUT NOTES: UNLESS OTHERWISE SPECIFIED, JP7 R32 3.3V 10K R27 10K JP6 R1 R3 150 JP4 3.3V 10K R20 R10 10K GND2 GND 300 OUT SENSE IN /SHDN IN R43 130 GCLK4_P GCLK4_N 400 R17 DNS R19 400 R15 R9 DNS 3 C24 2.2uF U4 LT3021 JP2 6 8 5 3.3V U3 LT1118 4 R40 50 2.5V R41 510 R39 100 R38 50 R37 130 2.5V R34 510 - + C39 4.7uF 1206 C23 22uF 1210 R5 DNS 4 2 8 2 4 OUT 7 - + 3 C46 0.1uF IN U5 LT1085 R2 100 EPF8119F U7B LT1816IMS8 7 16 15 14 11 10 T1 1 3 C31 10uF 1210 5V D1 BAT46 U7A LT1816IMS8 EXT C48 0.1uF IN- IN+ 1 /OUT E7 E1 E6 11 12 11 12 E5 E4 E3 E2 R36 0 U11 1 1 USB 1 USB_5V GND 1 J1 KLDHCX-0202X 2 2 3 3 2 4 6 8 8 4 GND GND 2 4 1 VTH1 1 3 5 7 2 4 6 8 1 3 5 7 VTH2 2 8 4 1 8 1 2Y GND 2A 3 2 1Y VCC 2Y 1A GND 2A 4 5 6 SDI_B 5V 5V 2 4 6 R56 1k 1 2 3 4 5 6 JP8 M_PROG 1 3 5 5V 5V R58 1k 4 SCK_B 5 6 CS_B U16 74LVC2G07 1Y VCC 1A SD1 1 3 2 5V R57 1k R42 33k 5V IO_L01P_7/VRN7 IO_L01N_7/VRN7 GND IO_L21P_7 IO_L21N_7 VCCO_7 VCCAUX IO_L23P_7 IO_L23N_7 GND IO_L40P_7 IO_L40N_7/VREF_7 IO_L40P_7/VREF_6 IO_L40N_6 IO_L40P_7 IO_L24N_6/VREF_6 IO VCCINT VCCO_6 GND IO IO_L01P_6/VRN_6 IO_L01N_6/VRP_6 M1 M0 FPGA_TDI PROG- RESET SW1 5V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 GPIO_M JP9 RESET R33 0 R31 0 R29 0 3.3V 1.2V 2.5V 3.3V U15 74LVC2G07 R4 75 2.5V C1 C3 C5 C7 C9 C11 C2 C4 C6 C8 C10 0.01uF 3.3V 3 GCLK4_N GCLK4_P 3.3V 1.2V C13 C15 C12 C14 0.01uF 2.5V 2.5V 3.3V 1.2V C27 C29 C33 C28 C30 C32 0.01uF 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 U8 XC3250 TDI PROG_B HSWAP_EN LO_L01N_0/VRP_0 IO_L01P_0/VRN_0 GND VCCO_0 VCCINT IO_L31N_0 IO_L31P_0/VREF_0 IO_L32N_0/GCLK7 IO_L32P_0/GCLKK6 IO_L32N_1/GCLK5 IO_L32P_1/GCLK4 IO_L31N_1/VREF_1 IO_L31P_1 VCCAUX VCCO_1 GND IO IO_L01N_1/VRP_1 IO_L01P_1/VRN TMS TCK TDO M2 IO_L01P_5/CS_B IO_L01N_5/RDWR_B GND IO_L28P_5/D7 VCCO_5 IO_L28N_5/D6 VCCAUX IO_L31P_5/D5 IO_L31N_5/D4 IO_L32P_5/GCLK2 IO_L32N_5/GCLK3 IO_L32P_4/GCLK0 IO_L32N_4/GCLK1 IO_L31P_4/DOUT/BUSY GND IO_L31N_4/INIT_B IO_L30P_4/D3 IO_L30P_4/D2 VCCINT VCCO_4 IO_L27P_4/D1 IO_L27N_4/DIN/D0 IO_L01P_4/VRN_4 IO_L01N_4/VRP_4 SDI_B 3 R52 47k 330 R45 C51 20pF USB_5V SDO_B SCK_B C50 100nF 3.3V 2.5V 1 R53 47k GPIO CS_B 2 1 2 U13 5V R54 0 DONE CCLK GPIO AVCC UVCC DD+ UGND UCAP PD0/OC0B/INT0 PD1/AIN0/INT1 PD2/AIN1/INT2 PD3/TXD1/INT3 PD4/INT5 PD5/XCK1/PCINT12 PD6/INT6/#RTS PD7/T0/INT7/#HWB/#CTS 2 THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS. 4 OE ON GND LED3 1 2 R46 470 R51 22 D+ D- R47 470 SCALE = NONE DATE: N/A SIZE CCLK DIN 1 2 3 4 5 6 7 8 9 10 3.3V DO NC CLK TDI TMS TCK CFOE/RST NC CE- C56 0.1uF 330 C54 100nF USB J4 CON-USB-5V 5V DD+ GND SW2 BOOT R48 10K FPGA_TDI 3.3V GPI0_F JP5 R18 56 C42 0.47uF C43 0.1uF 1 SHEET 1 SUPPORT BOARD FOR LTC6804 DEMO CIRCUIT 1907A Thursday, January 05, 2012 IC NO. 2 OF 1 REV. ISOLATED TWO WIRE SPI SERIAL SNIFFER 1630 McCarthy Blvd. Milpitas, CA 95035 Phone: (408)432-1900 www.linear.com Fax: (408)434-0507 LTC Confidential-For Customer Use Only 1 2 3 4 USB_5V TECHNOLOGY C55 0.1uF 5V R49 5V MOSI_L 5 4 2 20 19 18 17 16 15 14 13 12 11 3.3V 6 MISO_L PRTR5V0U4D U14 DATE CUYLER L. 01-05-12 APPROVED 1 SCK_L 3 CS 1 2 3 4 5 6 VCCJ VCCO VCC TD0 NC NC NC CEONC GND U6 XCF02S R13 4.7K R21 R22 R23 R24 DNS DNS DNS DNS CUYLER L. TITLE: SCHEMATIC AK 1 2 R44 470 R50 22 ER LED2 BUSY LED1 OUT VCC U12 100MHZ-OSC GCK0 3 DONE PROG- 1 REVISION HISTORY DESCRIPTION 2ND PROTOTYPE R12 330 2.5V R11 4.7K 3.3V 2 REV LOGIC ANALYZER JP13 OPT OE GND R55 OPT OUT __ ECO F_PROG JP12 4 1 2 R25 OPT 1 2 3 4 5 6 56 56 VCC APPROVALS C57 1uF 32 31 30 29 28 27 6 7 8 9 10 11 12 13 5 6 3 U10 GCK1 3 4 3.3V R16 R14 3.3V C49 3.3V 0.1uF C47 OPT 2.5V 3.3V CS SCK SCK_L MISO_L MOSI_L 3.3V 1.2V SDO SDI AT90USB162 C53 0.1uF 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 CUSTOMER NOTICE PC2/PCINT11 PC4/PCINT10 PC5/PCINT9/OC1B PC6/PCINT8/OC1A PC7/INT4/ICP1/CLKO PB0/SS/PCINT0 PB1/SCK/PCINT1 PB2/MOSI/PCINT2 PB3/MISO/PCINT3 PB4/T1/PCINT4 PB5/PCINT5 PB6/PCINT6 PB7/OC0A/OC1C/PCINT7 RESET XTAL1 XTAL2 C52 20pF 3.3V 1.2V IO_L01N_2/VRP_2 IO_L01P_2/VRN_2 GND IO_L21N_2 IO_L21P_2 VCCO_2 VCCINT IO_L24AN_2 IO_L24AP_2 GND IO_L40N_2 IO_L40P_2/VREF_2 IO_L40N_3/VREF_3 IO_L40P_3 IO_L24N_3 IO_L24P_3 IO VCCAUX VCCO_3 GND IO IO_L01N_3/VRP_3 IO_L01P_3/VRN_3 CLK DONE FPGA_TDO FPGA_TCK FPGA_TMS 2 LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO PCB DES. VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APP ENG. APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. 5 26 25 23 22 14 15 16 17 18 19 20 21 24 X1 HC-49US GCKL0 GCKL1 DIN 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 JP1 1 2 1 1 2 2 VTH2 VTH2 VTH2 4 VCC 3 3 VTH1 VTH1 2 2 1 1 3 3 VTH1 GND 4 5 6 1 8 4 5 6 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 3 1 2 5 A B C D DEMO MANUAL DC1907A Schematic Diagram dc1907af 13 DEMO MANUAL DC1907A DEMONSTRATION BOARD IMPORTANT NOTICE Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations. If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind. LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive. Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and observe good laboratory practice standards. Common sense is encouraged. This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer. Mailing Address: Linear Technology 1630 McCarthy Blvd. Milpitas, CA 95035 Copyright © 2004, Linear Technology Corporation dc1907af 14 Linear Technology Corporation LT 0813 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2013