cd00293107

UM1038
User manual
Hardware interconnection of the STM32™,
SPEAr™3xx, and ST75xx
1
Introduction
This user manual describes the STarGrid powerline modem, the latest family of powerline
modems from STMicroelectronics™. The powerline modem itself, although a powerful
device, always needs an external superior system which it uses in order to exchange
information with another node, where another powerline modem and superior system can
be found.
There are various superior systems and this document deals with the hardware
interconnection to powerline modems. These superior systems are from very simple 32-bit
microcontroller boards running standalone firmware to very complex 32-bit micro processor
units running operating systems. This document describes the possible ways of
interconnection and available HW and SW tools for building the system consisting of the
STM32 or SPEAr3xx, and powerline communication coming from the ST7570, 80, and 90
STarGrid family.
The related demonstration boards are:
April 2011
■
STEVAL-PCC012V1
■
STM3210C-EVAL
■
EVALSPEAr310
■
EVALSPEAr320PLC
■
EVALSPEAr320HMI
■
EVALST7570, 7570-1 KIT, 7580-1, 7590-1.
Doc ID 18303 Rev 1
1/24
www.st.com
Contents
UM1038
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
STM32 (STEVAL-PCC012V1) and EVALST7570-1 . . . . . . . . . . . . . . . . . . 5
3
STM32 (STEVAL-PCC012V1) and EVALST7590-1 . . . . . . . . . . . . . . . . . . 7
4
STM32 (STM3210C-EVAL) + EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . 9
5
SPEAr320 and EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6
EVALSPEAr310 and EVALST7590-1 via RS232 . . . . . . . . . . . . . . . . . . 11
7
SPEAr3xx and ST7570, ST7580, ST7590 via USB . . . . . . . . . . . . . . . . 13
8
EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART . . . . . . . 14
Appendix A HW images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
A.1
STM32 (STEVAL-PCC012V1) and EVALST7570-1 . . . . . . . . . . . . . . . . . 16
A.2
STM32 (STEVAL-PCC012V1) and EVALST7590-1 . . . . . . . . . . . . . . . . . 17
A.3
STM32 (STM3210C-EVAL) and EVALST7590-1 . . . . . . . . . . . . . . . . . . . 17
A.4
SPEAr320 and EVALST7590-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
A.5
SPEAr310 and EVALST7590-1 via RS232 . . . . . . . . . . . . . . . . . . . . . . . . 18
A.6
Any SPEAr3xx and ST7570, ST7580 or ST7590 via USB . . . . . . . . . . . . 19
A.7
EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART . . . . . . . . 20
Appendix B Additional schematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
B.1
STEVAL-PCC001V1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
B.2
Extension connectors at SPEAr320HMI board . . . . . . . . . . . . . . . . . . . . . 22
Appendix C Endnotes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2/24
Doc ID 18303 Rev 1
UM1038
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Interconnection of demonstration boards EVALST7570 and STEVAL-PCC012V1 . .
Interconnection of demonstration boards EVALST7590 and STEVAL-PCC012V1 . .
Interconnection of STM3210C-EVAL and EVALST7590-1. . . . . . . . . . . . . . . . . . . . .
STM3210C-EVAL jumper position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interconnection of EVALSPEAr320 and EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . .
EVALSPEAr320HMI, unified PLM connector CN704 (ST7570/80/90) . . . . . . . . . . . .
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Doc ID 18303 Rev 1
.....6
.....8
.....9
.....9
. . . . 10
. . . . 15
. . . . 23
3/24
List of figures
UM1038
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
4/24
EVALST7570 - microcontroller extension connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
STEVAL-PCC012V1 - PLM connector CN7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
STEVAL-PCC012V1 - board settings by JP2 and JP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connectors interconnection - 14-pin STM32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connectors interconnection - 20-pin ST7570 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
EVALST7590 - microcontroller extension connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
EVALST7590 - jumper setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STEVAL-PCC012V1 - PLM connector CN7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connectors interconnection - 14-pin STM32 and 14-pin ST7590. . . . . . . . . . . . . . . . . . . . . 8
SPEAr320 and EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EVALSPEAr310 and EVALST7590-1 via RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
STEVAL-PCC001V1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
EVALSPEAr3xx and ST7570, ST7580, ST7590 via USB . . . . . . . . . . . . . . . . . . . . . . . . . 13
EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART . . . . . . . . . . . . . . . . . . . . . 14
EVALSPEAr320HMI, unified PLM connector CN704 (ST7570/80/90) . . . . . . . . . . . . . . . . 14
ST7570 and STEVAL-PCC012V1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ST7590 and STEVAL-PCC012V1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ST7590 and STM3210C-EVAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SPEAr320 and EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SPEAr310 and EVALST7590-1 via RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Any SPEAr3xx and ST7570, ST7580 or ST7590 via USB . . . . . . . . . . . . . . . . . . . . . . . . . 19
SPEAr320HMI and ST7570 via the unified connector, UART . . . . . . . . . . . . . . . . . . . . . . 20
STEVAL-PCC001V1 schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SPEAr320HMI, CN701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SPEAr320HMI, CN702 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Doc ID 18303 Rev 1
UM1038
STM32 (STEVAL-PCC012V1) and EVALST7570-1
The demonstration boards necessary to connect the STM32 and ST7590 boards and their
configuration:
1.
2.
STEVAL-PCC012V1
●
Flash the correct firmware into STM32.
●
Configure the board according to Figure 3.
EVALST7590-1
●
Put the jumper into position JP12 - USB_RES (see paragraph 1
in Appendix C).
●
Interconnect EVALST7570-1 according to Table 1, Figure 4 and Figure 5.
Figure 1.
EVALST7570 - microcontroller extension connection
6##
*
6$$)/
6$$)/
2
4?2%1
'0)/?0
'0)/?0
'0)/?0
'0)/?0
'0)/?0
'0)/
2%3%4.?34
2%3%4. 6$$)/
3#,+?3#,
-/3)?3$!
-)3/
33.
3#,+
-/3)?48$
-)3/?28$
2
2
-/3)?48$
-)3/?28$
#/.!0
*0
#,/3%
!-
STEVAL-PCC012V1 - PLM connector CN7
53!24?4 8
Figure 2.
53!24?28
2
STM32 (STEVAL-PCC012V1) and EVALST7570-1
#.
4X$
-)3/
-/3)
RTS
-$-?2%3
2X$
6
33.
3#+
CTS
DFU
(EADER X !-
Doc ID 18303 Rev 1
5/24
STM32 (STEVAL-PCC012V1) and EVALST7570-1
Figure 3.
UM1038
STEVAL-PCC012V1 - board settings by JP2 and JP3
3$!?-%-3
3#,?-%-3
3$!
3#,
53!24?48 53!24?28 *0
*0
!-
Table 1.
Interconnection of demonstration boards EVALST7570 and STEVALPCC012V1
Signal
J5 (ST7570)
CN7 (STM32)
Color notation
TxD --> RX
16 (TxD)
1 (RX)
Blue
RxD <-- TX
18 (RxD)
2 (TX)
Green
T_REQ
15 (GPIO3)
11 (MDM_RES)
Purple
+3.3 V
Not connected
4
Red
GND
2
13, 14
Black
Figure 4.
Connectors interconnection - 14-pin STM32
!-
Figure 5.
Connectors interconnection - 20-pin ST7570
!-
6/24
Doc ID 18303 Rev 1
UM1038
STM32 (STEVAL-PCC012V1) and EVALST7590-1
The demonstration boards necessary to connect the STM32 and ST7590 boards and their
configuration:
1.
2.
STEVAL-PCC012V1
●
Flash the correct firmware into STM32.
●
Configure the board according to Figure 3.
EVALST7590-1
●
Put the jumper into position JP12 - USB_RES (see paragraph 1
in Appendix C).
●
Configure the board according to Figure 7.
●
Interconnect EVALST7590-1 according to Table 2 and Figure 9.
Figure 6.
EVALST7590 - microcontroller extension connector
*
-)3/?,6
-/3)?,6
243?,6
-$-?2%3N?,6 5!24?48$?,6
6##?,6
5!24?28$?,6
3#,+?,6
33.?,6
#43?,6
$&5?&/2#%?,6
#/.!
!-
Figure 7.
EVALST7590 - jumper setup
*0 5!24
*0
6##
5!24?28$
5!24?48$
30)
'0)/
5!24?28$
5!24?48$
'0)/
*0 #,/3%
!-
STEVAL-PCC012V1 - PLM connector CN7
53!24?4 8
Figure 8.
53!24?28
3
STM32 (STEVAL-PCC012V1) and EVALST7590-1
#.
4X$
-)3/
-/3)
RTS
-$-?2%3
2X$
6
33.
3#+
CTS
DFU
(EADER X !-
Doc ID 18303 Rev 1
7/24
STM32 (STEVAL-PCC012V1) and EVALST7590-1
Table 2.
UM1038
Interconnection of demonstration boards EVALST7590 and STEVALPCC012V1
Signal
J8 (ST7590)
CN7 (STM32)
TxD --> RX
1 (TxD_LV)
1 (RX)
RxD <-- TX
2 (RxD_LV)
2 (TX)
MDM_RES
11 (MDM_RESn_LV)
11 (MDM_RES)
MOSI_LV
7 (JP8 disconnected)
7 (MOSI) no collision if JP8 disconnected
MISO_LV
5
5 (MISO)(1)
SSN0
6
6 (SSN0) no collision
SCK
8
8 (SCK)(1)
+3.3 V
4 (VCC_LV)
4 (+3.3 V)
GND
13, 14
13, 14
1. Possible collision with SD Card™ (if inserted), Wi-Fi (if assembled), MEMS analog (if SPI signal used by
R63, R64 with zero value), MEMS digital (if plugged).
Figure 9.
Connectors interconnection - 14-pin STM32 and 14-pin ST7590(1)
!-
1. See paragraph 2 in Appendix C.
8/24
Doc ID 18303 Rev 1
UM1038
4
STM32 (STM3210C-EVAL) + EVALST7590-1
STM32 (STM3210C-EVAL) + EVALST7590-1
The demonstration boards necessary to connect the STM3210C-EVAL and EVALST7590
boards and their configuration:
1.
2.
STM3210C-EVAL
●
Configure the board: jumper positions according to Table 4.
●
Flash the correct firmware into STM32.
EVALST7590-1
●
Put the jumper into position JP12 - USB_RES (see paragraph 1
in Appendix C).
●
Interconnect EVALST7590-1 according to Table 3 and Figure 9.
Table 3.
Interconnection of STM3210C-EVAL and EVALST7590-1
Signals - STM3210C-EVAL
Cable color
ST7590 connector
+3.3 V (CN8 - pin 48)
Red
+5 V (or +3.3 V) (pin 4)
GND (CN8 - pin 50)
Black
GND (pin 14)
STM32 UART TX (CN9 - pin 12 - PD8)
Green
ST7590 RX (pin 2)
STM32 UART RX (CN9 - pin 8 - PD9)
Blue
ST7590 TX (pin 1)
Table 4.
STM3210C-EVAL jumper position
Signals - STM3210C-EVAL
ST7590 connector
JP25
USB - open, DTB - open, PSU - closed
JP26
Closed
JP15
SD position closed
JP13
No jumper
JP11
No jumper
JP12
No jumper
JP1
Anti_TMP position closed
JP24
No jumper
JP9
Closed
JP17
Closed
JP20
Open
Doc ID 18303 Rev 1
9/24
SPEAr320 and EVALST7590-1
5
UM1038
SPEAr320 and EVALST7590-1
Figure 10. SPEAr320 and EVALST7590-1
5!24
30%!R
0,-
6
34
BOARD
6
6
!-
The demonstration boards necessary to connect the EVALSPEAr320 and EVALST7590
boards and their configuration:
1.
2.
EVALSPEAr320
●
Interconnect PC with UART1.
●
Interconnect Ethernet to network.
●
Plug Flash disk with correct SW into the first USB, use the file system of this
USB.
EVALST7590-1
●
Put the jumper into position JP12 - USB_RES (see paragraph 1
in Appendix C).
●
Interconnect EVALST7590-1 and EVALSPEAr320 according to Table 5, Figure 9
and Figure 10.
Table 5.
10/24
Interconnection of EVALSPEAr320 and EVALST7590-1
Signals - EVALSPEAr320 - UART0
Cable color
ST7590 connector
+5 V (or +3.3 V) (J3 - pin 2)
Red
+5 V (or +3.3 V) (pin 4)
GND (J3 - pin 4)
Black
GND (pin 14)
SPEAr UART0 TX (J20 - pin 2)
Green
ST7590 RX (pin 2)
SPEAr UART0 RX (J21 - pin 2)
Blue
ST7590 TX (pin 1)
Doc ID 18303 Rev 1
UM1038
6
EVALSPEAr310 and EVALST7590-1 via RS232
EVALSPEAr310 and EVALST7590-1 via RS232
Figure 11. EVALSPEAr310 and EVALST7590-1 via RS232
23
30%!R
0,-
34%6!,
0##6
BOARD
6
5!24
53"6
6
34
6
!-
The demonstration boards necessary to connect the SPEAr310 and ST7590 boards and
their configuration:
1.
2.
3.
EVALSPEAr310
●
Interconnect PC with UART1.
●
Interconnect Ethernet to network.
●
Plug Flash disk with correct SW into the first USB, use file system of this USB.
●
Interconnect STEVAL-PCC001V1 with the second USB.
STEVAL-PCC001V1
●
Put jumper to JP5 (central position) in order to short pins 5 and 6, see Figure 12.
(see also paragraph 1 in Appendix C).
●
Cut CB1, CB2, and CB3.
●
Interconnect J3 - pin 2 with J7 - pin 6, see Figure 12 (see paragraph 1
in Appendix C).
●
Interconnect CB2, CB3, and J3 signals according toTable 5, Figure 12, and
Figure 9 with the ST7590 microcontroller extension connector.
EVALST7590-1
●
Put the jumper into position JP12 - USB_RES (see paragraph 1
in Appendix C).
●
Interconnect STEVAL-PCC001V1 according to Table 5 (Cable color and ST7590
connector columns) and Figure 9.
Doc ID 18303 Rev 1
11/24
EVALSPEAr310 and EVALST7590-1 via RS232
Figure 12. STEVAL-PCC001V1
12/24
Doc ID 18303 Rev 1
UM1038
UM1038
7
SPEAr3xx and ST7570, ST7580, ST7590 via USB
SPEAr3xx and ST7570, ST7580, ST7590 via USB
Figure 13. EVALSPEAr3xx and ST7570, ST7580, ST7590 via USB
30%!R
53"6
0,-
34XX
BOARD
6
6
!-
The demonstration boards necessary to connect the SPEAr3xx and ST7590 boards and
their configuration:
1.
2.
EVALSPEAr3xx:
●
Interconnect PC with UART1.
●
Interconnect Ethernet to network.
●
Plug Flash disk with correct SW into the first USB, use file system of this USB.
●
Interconnect EVALSPEAr3xx using the second USB with EVALST7570/80/90.
EVALST7590-1
●
Do not put the jumper into position JP12 - USB_RES (see paragraph 1
in Appendix C).
Doc ID 18303 Rev 1
13/24
EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART
8
UM1038
EVALSPEAr320HMI and ST7570, ST7580, ST7590 via
UART
Figure 14. EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART
5!24
30%!R
6
BOARD
0,
34
34
34
6
6
!-
The demonstration boards necessary to connect the EVALSPEAr3xx with the ST7570/80/90
board and their configuration:
1.
2.
EVALSPEAr3xx
●
Plug Flash disk with correct SW into the first USB, use file system of this USB.
●
Interconnect connector CN704 with EVALST75xx unified extension connector
(Table 6) by the flat ribbon cable as shown in Figure 24 and Figure 25. If
additional signals are needed use information from Figure 25.
EVALST75xx
●
Put the jumper into position JP12 - USB_RES (see paragraph 1
in Appendix C).
Figure 15. EVALSPEAr320HMI, unified PLM connector CN704 (ST7570/80/90)
6
5! 24 ?28
5! 24 ?48
0,?'0) /
0,?'0) /
0,?'0) /
0,?'0) /
#.
!-
14/24
Doc ID 18303 Rev 1
UM1038
EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART
Table 6.
EVALSPEAr320HMI, unified PLM connector CN704 (ST7570/80/90)
Signal
ST7570 + 80/90
CN7
Color notation
TxD --> RX
3 (TxD)
3 (RX)
Blue
RxD <-- TX
5 (RxD)
5 (TX)
Green
Auxiliary IO1
7 (TREQ / RTS)
7 (PL GPIO39)
Purple
Auxiliary IO2
9 (BR1 / CTS)
9 (PL GPIO34)
Purple
Auxiliary IO3
11 (BR2 / DFU)
11 (PL GPIO35)
Purple
Auxiliary IO4
13 (RESETN / MDM)
13 (PL GPIO21)
Purple
+3.3 V
1
1
Red
GND
10, 12, 14
10, 12, 14
Black
Doc ID 18303 Rev 1
15/24
HW images
UM1038
Appendix A
A.1
HW images
STM32 (STEVAL-PCC012V1) and EVALST7570-1
Figure 16. ST7570 and STEVAL-PCC012V1
16/24
Doc ID 18303 Rev 1
UM1038
A.2
HW images
STM32 (STEVAL-PCC012V1) and EVALST7590-1
Figure 17. ST7590 and STEVAL-PCC012V1
A.3
STM32 (STM3210C-EVAL) and EVALST7590-1
Figure 18. ST7590 and STM3210C-EVAL
Doc ID 18303 Rev 1
17/24
HW images
A.4
UM1038
SPEAr320 and EVALST7590-1
Figure 19. SPEAr320 and EVALST7590-1
A.5
SPEAr310 and EVALST7590-1 via RS232
Figure 20. SPEAr310 and EVALST7590-1 via RS232
18/24
Doc ID 18303 Rev 1
UM1038
A.6
HW images
Any SPEAr3xx and ST7570, ST7580 or ST7590 via USB
Figure 21. Any SPEAr3xx and ST7570, ST7580 or ST7590 via USB
Doc ID 18303 Rev 1
19/24
HW images
A.7
UM1038
EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART
Figure 22. SPEAr320HMI and ST7570 via the unified connector, UART
20/24
Doc ID 18303 Rev 1
UM1038
Additional schematics
Appendix B
B.1
Additional schematics
STEVAL-PCC001V1
Figure 23. STEVAL-PCC001V1 schematic
6##
#"
#
*UNCTIONON
*UNCTION
#
/.
'.$
4/54
4/54
2).
2).
2/54
2/54
6
6n
#
#"
*UNCTION
*UNCTIONON
6##
*
6##
#
/. *5-0%2
#"
'.$
5
'.$
'.$
%.
3($.
*
#/.?X !
4).
4).
#
#n
344 33/0
*5-0%2
'.$ *
#
#n
6##
#
#
'.$
*UNCTIONON
TI
0
$35"-
/.
28
48
'.$
*
6##
6##
2
N& #
'.$
'.$
#
P&
3#,(30&
3$!(30&
!).0&
!).0&
53"%.(30&
)###,+(30&
)##$! 4! (30&
'.$
-(Z
#34#7-
9
'.$
#
P&
'.$
'.$
0#
0#
0#
0#
0! $4#
0! $4#
0! $4#
0! $4#
0! $4#
0! $4#
0! $4#
0! $4#
34?4 1&0
/3#).
/3#/54
633
6$$
0#(3$4#3#+
0#(3$4#-/3)
0#(3$4#-)3/
0#(3-#/33
5
6$$
6$$A
633A
633
9
0"$4#
0"$4#
0"$4#
0"$4#
0"$4#
0"$4#
'.$
)##3%,600
2%3%4
0%(3$4#
0%(3$4#
0%(3$4#
07-0%
6$$F
633F
53"633
53"$53"$0
53"6##
53"6$$
$4#!).07-0%
$4#!).(30%
$4#!).(30%
$4#!).(30%
!).0$
!).0$
/3-00$
/#-00$
0$
0$
0$
0$
#
N&
2
2
#/.?X '.$
0"$4#
0"$4#
6##
N&
#
N&
#
'.$
6##
3
+
3 6
$n
$
3 '.$
53"8"
2
#
N&
6##
'.$
2
*
#/.?X $
,%$?28
2
#
N&
3
$
,%$?48
'.$
2
2
$
,%$?0/7%2
Doc ID 18303 Rev 1
6##
!)6
21/24
Additional schematics
B.2
UM1038
Extension connectors at SPEAr320HMI board
Figure 24. SPEAr320HMI, CN701
6
)#?3#,
)#?3#,
0,?'0)/
0,?'0)/
0,?'0)/
0,?'0)/
0,?'0)/
0,?'0)/
0,?'0)/
0,?'0)/
6
#.
)#?3$!
)#?3$!
6
(EADER X !-
Figure 25. SPEAr320HMI, CN702
6
330?-)3/
330?#,+
0?#!.(
#.
)#?3#,
330?-)3/
330?#,+
0?#!.(
!).
!).
0, ?'0)/?0
0, ?'0)/?0
6
)#?3$!
330?-/3)
330?33
0?#!.,
!).
5!24?48
5!24?28
330?-/3)
330?33
0?#!.,
0,?'0)/?0
5!24?48
5!24?28
(EADER X !-
22/24
Doc ID 18303 Rev 1
UM1038
Endnotes
Appendix C
Endnotes
1.
The tri-states output pins of the FTDI chip FT232 are used on EVALST7590-1 in order
to make it possible to use an external microcontroller to control the EVALST7590-1
board. (The FTDI chip should be also in reset when not connected to USB).
2.
This interconnection does not implement signals for asynchronous communication from
ST7590 to STM32.
Revision history
Table 7.
Document revision history
Date
Revision
18-Apr-2011
1
Changes
Initial release.
Doc ID 18303 Rev 1
23/24
UM1038
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
24/24
Doc ID 18303 Rev 1