Low Drop Voltage Regulator TLE 4276-2 Features • • • • • • • • • • • 5 V or variable output voltage Output voltage tolerance ≤ ±2% 400 mA current capability Low-drop voltage Inhibit input Very low current consumption Short-circuit-proof Reverse polarity proof Suitable for use in automotive electronics Green Product (RoHS compliant) AEC Qualified P-TO220-5-122 P-TO252-5-11 Type Package Marking TLE 4276-2 GV50 PG-TO263-5 4276-2V5 TLE 4276-2 GV PG-TO263-5 4276-2V TLE 4276-2 DV50 PG-TO252-5 4276-2V5 TLE 4276-2 DV PG-TO252-5 4276-2V Data Sheet 1 Rev. 1.1, 2007-09-21 TLE 4276-2 Functional Description The TLE 4276-2 is a low-drop voltage regulator in a TO package. The IC regulates an input voltage up to 40 V to VQ,nom = 5.0 V (V50) or adjustable voltage (V). The maximum output current is 400 mA. The IC can be switched off via the inhibit input, which causes the current consumption to drop below 10 µA. The IC is short-circuit-proof and includes temperature protection which turns off the device at overtemperature. Dimensioning Information on External Components The input capacitor CI is necessary for compensation of line influences. Using a resistor of approx. 1 Ω in series with CI, the oscillating of input inductivity and input capacitance can be damped. The output capacitor CQ is necessary for the stability of the regulation circuit. Stability is guaranteed at values CQ ≥ 22 µF and an ESR of ≤ 3 Ω within the operating temperature range. Circuit Description The control amplifier compares a reference voltage to a voltage that is proportional to the output voltage and drives the base of the series transistor via a buffer. Saturation control as a function of the load current prevents any oversaturation of the power element. The IC also incorporates a number of internal circuits for protection against: • • • Overload Overtemperature Reverse polarity Data Sheet 2 Rev. 1.1, 2007-09-21 TLE 4276-2 PG-TO263-5 PG-TO252-5 GND 1 5 1 5 Ι Ι GND INH Q INH N.C. (VA) Q N.C. (VA) AEP02560 AEP02043 Figure 1 Pin Configuration (top view) Table 1 Pin Definitions and Functions Pin No. Symbol Function 1 I Input; block to ground directly at the IC with a ceramic capacitor. 2 INH Inhibit; low-active input. 3 GND Ground 4 N.C. VA Not connected for V50 Voltage Adjust Input; only for adjustable version. Connect an external voltage divider to determine the output voltage. 5 Q Output; block to GND with a ≥ 22 µF capacitor, ESR ≤ 3 Ω at 10 kHz Heat Tab Data Sheet Connect to GND. 3 Rev. 1.1, 2007-09-21 TLE 4276-2 Saturation Control and Protection Circuit Temperature Sensor Ι 1 6 Control Amplifier Q Buffer Bandgap Reference *) **) 2 4 3 INH VA GND *) For fixed Voltage Regulator only **) For adjustable Voltage Regulator only Figure 2 Data Sheet AEB02044 Block Diagram 4 Rev. 1.1, 2007-09-21 TLE 4276-2 Table 2 Absolute Maximum Ratings Parameter Symbol Limit Values Unit Test Condition 45 V – – – – Internally limited VINH -42 45 V – VVA -0.3 10 V – VQ IQ -1.0 40 V – – – – Internally limited IGND – 100 mA – Tj Tstg -40 150 °C – -50 150 °C – Min. Max. VI II -42 Input I Voltage Current Inhibit INH Voltage Voltage Adjust Input VA Voltage Output Q Voltage Current Ground GND Current Temperature Junction temperature Storage temperature Note: Maximum ratings are absolute ratings; exceeding any one of these values may cause irreversible damage to the integrated circuit. Table 3 ESD Rating Parameter Symbol Limit Values ESD Capability VESD,HBM -2 Min. Data Sheet Unit Notes kV Human Body Model Max. 2 5 Rev. 1.1, 2007-09-21 TLE 4276-2 Table 4 Operating Range Parameter Symbol Limit Values Min. Max. Unit Remarks Input voltage VI VQ + 0.5 40 V Fixed voltage device V50 Input voltage VQ + 0.5 40 V Variable device V Input voltage VI VI 4.5 V 40 V Variable device V, VQ < 4 V Junction temperature Tj -40 150 °C – Unit Conditions Table 5 Thermal Resistance Parameter Symbol Limit Value Min. Typ. Max. RthJC RthJA – 3.0 – K/W – Junction to Ambient1) – 78 – K/W PG-TO252-5 300mm2 heatsink area on PCB2) Junction to Ambient1) RthJA – 53 – K/W PG-TO263-5 300mm2 heatsink area on PCB2) Junction to Case1) 1) not subject to production test, specified by design 2) EIA/JESD 52_2, FR4, 80 × 80 × 1.5 mm; 35µ Cu, 5µ Sn Data Sheet 6 Rev. 1.1, 2007-09-21 TLE 4276-2 Table 6 Characteristics VI = 13.5 V; -40 °C < Tj < 150 °C (unless otherwise specified) Parameter Symbol Min. Typ. Max. Unit Measuring Condition Output voltage VQ 4.9 5.0 5.1 V 1 V50-Version 5 mA < IQ < 300 mA 6 V < VI < 28 V Output voltage VQ 4.8 5.0 5.2 V V50-Version 1 5 mA < IQ < 400 mA 6 V < VI < 28 V Output voltage VQ 4.8 5.0 5.2 V 1 V50-Version 5 mA < IQ < 200 mA 6 V < VI < 40 V Output voltage tolerance ∆VQ -2 – 2 % V-Version 1 R2 < 50 kΩ VQ + 1 V ≤ VI ≤ 28 V VI > 4.5 V 5 mA ≤ IQ ≤ 300 mA Output voltage tolerance ∆VQ -4 – 4 % V-Version 1 R2 < 50 kΩ VQ + 1 V ≤ VI ≤ 40V VI > 4.5 V 5 mA ≤ IQ ≤ 400 mA Output current limitation1) IQ 400 600 1100 mA Current consumption; Iq = II - IQ Iq – – 10 Current consumption; Iq = II - IQ Iq – 100 Current consumption; Iq = II - IQ Iq – Current consumption; Iq = II - IQ Iq – Data Sheet Limit Values Measuring Circuit – 1 µA VINH = 0 V; Tj ≤ 100 °C 1 220 µA IQ = 1 mA 1 5 10 mA IQ = 250 mA 1 15 25 mA IQ = 400 mA 1 7 Rev. 1.1, 2007-09-21 TLE 4276-2 Table 6 Characteristics (cont’d) VI = 13.5 V; -40 °C < Tj < 150 °C (unless otherwise specified) Parameter Drop voltage1) Symbol Min. Typ. Max. Limit Values VDR – 250 Unit 500 mV Measuring Condition Measuring Circuit V50 1 IQ = 250 mA VDR = VI - VQ Drop voltage1) VDR – 250 500 mV variable devices 1 IQ = 250 mA VI > 4.5 V VDR = VI - VQ IQ = 5 mA to 400 mA 1 ∆Vl = 12 V to 32 V 1 IQ = 5 mA fr = 100 Hz; 1 Vr = 0.5 Vpp Load regulation ∆VQ,Lo – 5 35 mV Line regulation ∆VQ,Li – 15 25 mV Power supply ripple rejection PSRR – 54 – dB Temperature output voltage drift dVQ/dT – 0.5 – – – mV/K Inhibit on voltage VINH – 2 3.5 V VQ ≥ 4.9 V 1 Inhibit off voltage VINH 0.5 1.7 – V VQ ≤ 0.1 V 1 Input current IINH 5 10 20 µA VINH = 5 V 1 Inhibit 1) Measured when the output voltage VQ has dropped 100 mV from the nominal value obtained at VI = 13.5 V. Data Sheet 8 Rev. 1.1, 2007-09-21 TLE 4276-2 II Input 100 µF I 1 IQ 5 Q Output CQ 100 nF 22 µF TLE 4276-2 IINH VI INH 2 VINH *) Optional 4 3 GND R 1*) VQ *) VA Voltage Adjust R 2*) for adjustable Voltage Regulator Figure 3 RL AES02045 Measuring Circuit I 1 Input CI e.g. KL 15 2 4 3 GND *) Optional Figure 4 Data Sheet CQ TLE 4276-2 INH Output 5 Q for adjustable Voltage Regulator R 1*) *) VA Voltage Adjust R 2*) AES02046 Application Circuit 9 Rev. 1.1, 2007-09-21 TLE 4276-2 Application Information for Variable Output Regulator TLE 4276-2 DV, GV The output voltage of the TLE 4276-2 DV, GV can be adjusted between 2.5 V and 20 V by an external output voltage divider, closing the control loop to the voltage adjust pin VA. The voltage at pin VA is compared to the internal reference of typical 2.5 V in an error amplifier. It controls the output voltage. 5 Q Internal Reference 2.5 V Typical Current and Saturation Control Vref R1 CQ 22 µF 4 VA R2 AEB02804 Figure 5 Application Detail External Components at Output for Variable Voltage Regulator The output voltage is calculated according to Equation (1): VQ = (R1 + R2)/R2 × Vref, neglecting IVA (1) Vref is typically 2.5 V. To avoid errors caused by leakage current IVA, we recommend to choose the resistor value R2 according to Equation (2): R2 < 50 kΩ (2) For a 2.5 V output voltage the output pin Q is directly connected to the adjust pin VA. The accuracy of the resistors R1 and R2 add an additional error to the output voltage tolerance. The operation range of the variable TLE 4276-2 DV, GV is VQ + 0.5 V to 40 V. For internal biasing a minimum input voltage of 4.3 V is required. For output voltages below 4 V the voltage drop is 4.3 V - VQ Data Sheet 10 Rev. 1.1, 2007-09-21 TLE 4276-2 Typical Performance Characteristics V50: Voltage VDR versus Output Current IQ Max. Output Current IQ versus Input Voltage VI AED03017 600 mV VDR IQ AED03020 800 mA 500 600 T j = 125 ˚C 400 T j = 25 ˚C VQ = 0 V 300 400 200 T j = 25 ˚C 200 100 0 0 100 200 0 300 mA 400 0 10 20 30 40 V 50 IQ VI Current Consumption Iq versus Output Current IQ (high load) Current Consumption Iq versus Output Current IQ (low load) AED03021 60 AED03022 0.6 Iq mA Iq mA 50 0.5 40 0.4 T j = 25 ˚C VI = 13.5 V 0.3 30 T j = 25 ˚C VI = 13.5 V 20 0.2 10 0.1 0 0 100 200 300 400 0 mA 600 Data Sheet 0 10 20 30 40 mA 60 IQ IQ 11 Rev. 1.1, 2007-09-21 TLE 4276-2 Typical Performance Characteristics for V50: Output Voltage VQ versus Temperature Tj Current Consumption Iq versus Input Voltage VI AED03081 5.2 VQ AED01967 30 V Ιq mA 5.1 20 VI = 13.5 V T j = 25 C R L = 20 Ω 5.0 10 4.9 4.8 -40 0 40 80 0 120 ˚C 160 0 10 20 30 Tj Low Voltage Behavior High Voltage Behavior AED01968 6 VQ 50 V VΙ V VQ 5 AED03082_4276 3.5 mA II 3.0 2.5 4 2.0 VI = VQ 1.5 3 T j = 25 ˚C R L = 20 Ω T j = 25 ˚C R L = 6.8 k Ω 1.0 2 0.5 1 0 0 0 2 4 6 -2 -50 8 V 10 Data Sheet -25 0 25 V 50 VI VI 12 Rev. 1.1, 2007-09-21 TLE 4276-2 Package Outlines ! " X X - ! " -!8 4YPICAL -ETALSURFACEMIN89 !LLMETALSURFACESTINPLATEDEXCEPTAREAOFCUT " '04 Outlines_PG-TO263-5 Figure 6 PG-TO263-5 (Plastic Green Transistor Single Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. Dimensions in mm SMD = Surface Mounted Device Data Sheet 13 Rev. 1.1, 2007-09-21 TLE 4276-2 6.5 +0.15 -0.05 A 1) 2.3 +0.05 -0.10 B (5) 0.51 MIN. 0.15 MAX. per side 0.5 +0.08 -0.04 0.9 +0.20 -0.01 0...0.15 0.8 ±0.15 (4.24) 1 ±0.1 9.98 ±0.5 6.22 -0.2 5.7 MAX. 5 x 0.6 ±0.1 0.5 +0.08 -0.04 1.14 4.56 0.1 B 0.25 M A B 1) Includes mold flashes on each side. All metal surfaces tin plated, except area of cut. Outlines_PG-TO252-5 Figure 7 PG-TO252-5 (Plastic Green Transistor Single Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. Dimensions in mm SMD = Surface Mounted Device Data Sheet 14 Rev. 1.1, 2007-09-21 TLE 4276-2 Revision History Version Date Rev. 1.0 2007-08-07 First Version Data Sheet Rev. 1.1 2007-09-21 Second Version Data Sheet Data Sheet Changes 15 Rev. 1.1, 2007-09-21 Edition 2007-09-21 Published by Infineon Technologies AG 81726 Munich, Germany © 2007 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.