Sulfur Tolerant Chip Resistors TRR Series Datasheet Features 1) Special construction prevents sulfur gas penetration, significantly increasing reliability. 2) ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. Products List Size Part No. (mm) (inch) Rated Power Limiting Element Voltage (70˚C) (W) (V) Temperature Coefficient Resistance Tolerance (ppm / °C) (%) +500 / −250 TRR01 1005 0402 0.063 ±200 50 J(±5%) Resistance Range 1Ω to 9.1Ω E24 10Ω to 10MΩ ±100 F(±1%) Operating Temperature Range (°C) Series 10Ω to 2.2MΩ Jumper type : Rmax = 50m Ω / Imax. = 1A ±400 TRR03 1608 0603 0.1 J(±5%) ±200 50 1Ω to 9.1Ω E24 10Ω to 10MΩ ±100 F(±1%) 10Ω to 10MΩ Jumper type : Rmax = 50m Ω / Imax. = 1A ±400 TRR10 2012 0805 0.125 J(±5%) ±200 150 1Ω to −55 to +155 9.1Ω E24 10Ω to 10MΩ ±100 F(±1%) 10Ω to 2.2MΩ Jumper type : Rmax = 50m Ω / Imax. = 2A ±400 TRR18 3216 1206 0.25 J(±5%) ±200 200 1Ω to 9.1Ω E24 10Ω to 10MΩ ±100 F(±1%) 10Ω to 2.2MΩ Jumper type : Rmax = 50m Ω / Imax. = 2A ∗Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Part Number Description T R R 0 1 M Z P J Part No. Size (mm [inch]) Packaging Specifications Code TRR 01 (1005 [0402]) 03 (1608 [0603]) 10 (2012 [0805]) 18 (3216 [1206]) Part No. Code Packaging specifications Quantity / Reel TRR01 MZP Paper tape (2mm Pitch) 10,000 TRR03 EZP Paper tape (4mm Pitch) 5,000 TRR10 EZP Paper tape (4mm Pitch) 5,000 TRR18 EZP Paper tape (4mm Pitch) 5,000 (Sulfur Tolerant Chip Resistors) Resistance Tolerance D ( ±0.5% ) F ( ±1% ) J ( ±5% ) 1 0 5 Nominal Resistance Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance tolerance F J Resistance code : : 4 digits 3 digits Ex.) 1Ω = 1R0 9.1Ω = 9R1 10 Ω = 10R0 100 1M Ω = 1004 105 www.rohm.com c 2014 ROHM Co., Ltd. All rights reserved. ○ 1/4 ( ±5% ) ( ±5% ) ( ±1%) ( ±5% ) ( ±1%) ( ±5% ) 2014.12 - Rev.C TRR Series Data Sheet Chip Resistor Dimensions and Markings TRR01 / 03 TRR10 / 18 L L W W a a t t b b (Unit : mm) Marking existence ∗Including jumper type Part No. (mm) (inch) L W t a b TRR01 1005 0402 1.0±0.05 0.5±0.05 0.35±0.05 0.33±0.08 0.25 −0.1 No TRR03 1608 0603 1.6±0.1 0.8±0.1 0.45±0.1 0.4±0.1 0.3±0.2 No TRR10 2012 0805 2.0±0.1 1.25±0.1 0.55±0.1 0.43 −0.1 0.4±0.2 No TRR18 3216 1206 3.2±0.15 1.6±0.15 0.55±0.1 0.69 −0.15 0.5±0.25 No +0.15 +0.2 +0.05 Land pattern Example B D C Land A (Unit : mm) Dimensions A B C D TRR01 0.5 1.3 0.5 0.4 TRR03 1.0 2.0 0.8 0.5 TRR10 1.2 2.6 1.15 0.7 TRR18 2.2 4.0 1.5 0.9 Part No. www.rohm.com c 2014 ROHM Co., Ltd. All rights reserved. ○ 2/4 2014.12 - Rev.C TRR Series Data Sheet Derating Curve When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below. TRR01 / 03 / 10 / 18 PERCENT RATED POWER (%) 100 80 60 40 20 0 −55 0 70 100 AMBIENT TEMPERATURE (°C) 155 Characteristics Test Items Guaranteed Value Resistor Type Jumper Type Test Conditions Resistance See P.1 20°C Variation of resistance with temperature See P.1 Measurement : +20 / −55 / +20 / +125°C Overload Solderability Resistance to soldering heat ± (2.0%+0.1Ω) Max. 50mΩ A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. ± (1.0%+0.05Ω) Max. 50mΩ No remarkable abnormality on the appearance. Rated voltage (current) ×2.5, 2s Maximum overload voltage Rosin·Ethanol : 25% (Weight) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s Soldering condition : 260±5°C Duration of immersion : 10±1s Rapid change of temperature ± (1.0%+0.05Ω) Max. 50mΩ Test temp. : −55°C to +125°C 5cycle Damp heat, steady state ± (3.0%+0.1Ω) Max. 100mΩ 40°C, 93%RH (Relative Humidity) Test time : 1,000h to 1,048h Endurance at 70°C ± (3.0%+0.1Ω) Max. 100mΩ 70°C Rated voltage (current) 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h Endurance ± (3.0%+0.1Ω) Max. 100mΩ 155°C Test time : 1,000h to 1,048h Resistance to solvent ± (1.0%+0.05Ω) Max. 50mΩ 23±5°C, Immersion cleaning, 5±0.5min Solvent : 2−propanol ± (1.0%+0.05Ω) Max. 50mΩ Bend strength of the end face plating Without mechanical damage such as breaks. − Compliance Standard(s) : IEC60115−8 JISC 5201−8 www.rohm.com c 2014 ROHM Co., Ltd. All rights reserved. ○ 3/4 2014.12 - Rev.C TRR Series Data Sheet Tape Dimensions (Unit : mm) Paper Tape Part No. W F E A0 B0 TRR01 8.0±0.3 3.5±0.05 1.75±0.1 0.7±0.1 1.2±0.1 TRR03 8.0±0.3 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1 TRR10 8.0±0.3 3.5±0.05 1.75±0.1 1.65 TRR18 8.0±0.3 3.5±0.05 1.75±0.1 1.95 Part No. D0 P0 P1 P2 T2 P0 P2 P1 φD0 E F W B0 A0 Top tape Base paper (Bottom tape) Components Cavity T2 +0.2 −0.1 +0.1 −0.05 2.4 3.5 +0.2 −0.1 +0.15 −0.05 TRR01 φ1.5 +0.1 0 4.0±0.1 2.0±0.05 2.0±0.05 Max 1.1 TRR03 φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 TRR10 φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 TRR18 φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 02 04 06 A 08 06 D 04 B 02 A 08 Reel Dimensions B D C Label C Label ACCORDING TO EIAJ ET-7200B ACCORDING TO EIAJ ET-7200B (RRV) (Unit : mm) Part No. A B C D TRR01 TRR03 φ180 TRR10 0 −1.5 φ60 +1.0 0 9 +1.0 0 φ13±0.2 TRR18 www.rohm.com c 2014 ROHM Co., Ltd. All rights reserved. ○ 4/4 2014.12 - Rev.C Notice Notes 1) The information contained herein is subject to change without notice. 2) Before you use our Products, please contact our sales representative and verify the latest specifications : 3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the rating specified by ROHM. 4) Examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. 5) The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. 6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. 7) The Products specified in this document are not designed to be radiation tolerant. 8) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. 9) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. 10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. 11) ROHM has used reasonable care to ensur the accuracy of the information contained in this document. However, ROHM does not warrants that such information is error-free, and ROHM shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. 12) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. 13) When providing our Products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act. 14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2014 ROHM Co., Ltd. All rights reserved. R1102A