NXP Semiconductors User’s Guide Document Number: KTTWRSB0800-36EVBUG Rev. 1.0, 1/2016 TWR-SB0800-36EVB Tower System Platform Figure 1. TWR-SB0800-36EVB © NXP Semiconductors N.V. 2016. All rights reserved. Contents 1 2 3 4 5 6 7 8 9 10 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Understanding the Tower System Modular Development Board Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Getting to Know the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Setting up the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Board Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 2 NXP Semiconductors Important Notice 1 Important Notice Freescale provides the enclosed product(s) under the following conditions: This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and supply terminals. This evaluation board may be used with any development system or other source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. This evaluation board is not a Reference Design and is not intended to represent a final design recommendation for any particular application. Final device in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality. The goods provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end product incorporating the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical support services. Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the date of delivery and will be replaced by a new kit. Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typical”, must be validated for each customer application by customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale product could create a situation where personal injury or death may occur. Should the Buyer purchase or use Freescale products for any such unintended or unauthorized application, the Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges Freescale was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2016 TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 3 Getting Started 2 Getting Started 2.1 Kit Contents/Packing List The TWR-SB0800-36EVB contents include: • TWR-SB0800-36EVB tower board • Plug-in connectors • Warranty card 2.2 Jump Start Freescale’s analog product development boards help to easily evaluate Freescale products. These tools support analog mixed signal and power solutions including monolithic ICs using proven high-volume SMARTMOS mixed signal technology, and system-in-package devices utilizing power, SMARTMOS and MCU dies. Freescale products enable longer battery life, smaller form factor, component count reduction, ease of design, lower system cost, and improved performance in powering state of the art systems. • Go to www.nxp.com/TWR-SB0800-36EVB • Review your Tool Summary Page • Look for Jump Start Your Design • Download the documents, software and other resources Once the files are downloaded, review the user guide in the bundle. The user guide includes setup instructions, BOM, and schematics. Jump start bundles are available on each tool summary page with the most relevant and current information. The information includes everything needed for design. 2.3 Required Equipment and Software To use this kit, you need: • Power supply 6.0 V to 36 V with current limit set initially to 2.5 A to 9.0 A • Oscilloscope (preferably 4-channel) with current probe(s) • Digital multimeter • Typical loads: (DC motor, valve) • TWR-KL25Z48M, K20D72M, KV31F120M or other Tower boards (check compatibility) • Kinetis Design Studio or compatible CodeWarrior for MCUs (Eclipse IDE). For information on getting started with CodeWarrior, see the MC34ValveController Processor Expert Component User Guide. 2.4 System Requirements The kit requires the following to function properly with the software: • USB-enabled PC with Windows® XP or higher TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 4 NXP Semiconductors Understanding the Tower System Modular Development Board Platform 3 Understanding the Tower System Modular Development Board Platform Freescale’s Tower System peripheral module is designed to be combined and used with other Tower System modules. The Tower System is a modular development platform for 8-, 16-, and 32-bit MCUs and MPUs enabling advanced development through rapid prototyping. Featuring more than fifty development boards or modules, the Tower System provides designers with building blocks for entry-level to advanced MCU development. Figure 2 shows a Tower System platform with the TWR-SB0800-36EVB configured with another Tower System module, the TWR-KL25Z48M board. TWR-SB0800-36EVB or TWR-SB0410-36EVB Elevator Board (Primary) Elevator Board (Secondary) Tower MCU Board (TWR-KL25Z48M in this example) Figure 2. TWR-SB0800-36EVB on Tower System TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 5 Understanding the Tower System Modular Development Board Platform 3.1 Block Diagram Power Supply 6.0 V to 36 V Digital Supply 5.0 V Primary Elevator MCU Tower Board Selection (Jumpers) Valves Valves x4 x4 MC34SB0800 Motor Warning Lamp Octal Valves Controller x2 Secondary Elevator SPI (single, daisy chain) GPIO & ADC input (x3) Tower System Interface Figure 3. Block Diagram Note: Warning lamp application is proposed as an example in Figure 3. The lamp is connected to the low-side driver (general purpose). TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 6 NXP Semiconductors Getting to Know the Hardware 4 Getting to Know the Hardware 4.1 Board Overview The TWR-SB0800-36EVB is a tower peripheral module that exercises valve control functions on SoC products based on the Tower System. The Tower System acts as a debug and communication port for the PC being used to debug/download programs from the Kinetis Design Studio/CodeWarrior system. 4.2 Board Features The board features are as follows: • Valve controller with embedded safety features: MC34SB0800 • Four current regulated valve driver outputs (maximum current: 2.25 A; maximum frequency 5.0 kHz) • Four PWM valve driver outputs (maximum current 5.0 A; maximum frequency 5.0 kHz) • High-side pre-driver Safe Switch • High-side pre-driver motor control (maximum frequency 500 Hz) • Embedded Safety Supervision • Simplified MCU connections • SPI daisy chain communication with other TWR-SB0800-36EVB or TWR-0410-36EVB boards (daisy chain mode jumper selectable) • Single SPI communication support • On-board LED ON/OFF indicators for each high-side and low-side (general purpose) channel • Three 10-bit ADC inputs 4.3 Device Features This tower system features the following NXP product: Table 1. Device Features Device Description Features Control Features • Operating voltage up to 36 V • Four low-side drivers regulate up to 2.25 A • ± 2.0% precision reachable with calibration • Four low-side drivers PWM up to 5 kHz with a maximum current capability up to 5.0 A • Integrated low-side drivers to save PCB space • ADC monitoring of external or internal signals to enhance the control unit safety level • Single SPI device control MC34SB0800 Octal Valve Controller System on Chip • MCU sent only when current or duty-cycle is targeted through the SPI • MCU does not need to generate PWM signals at high frequency Safety Features • Safe MOSFET turns off valves and motor when problems occur • Watchdog feature • Under-voltage, over-voltage clock fail detection • Open load, short circuit, over-temperature detection on each low side • VDS monitoring of each low-side driver in real time • Over-current and over-temperature detection on the high-side pre-driver TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 7 Getting to Know the Hardware 4.4 Board Description Jumper Block (Daisy Chain/Input PWM Motor Control Selection) Primary Elevator (White Strip) Reset Switch MC34SB0800 Secondary Elevator Figure 4. Board Overview Table 2. Board Description Name Description Reset switch Resets the MC34SB0800 device Primary Elevator Edge connector to primary elevator board (white stripe to white connector on elevator board) Secondary Elevator Edge connector to secondary elevator board Daisy chain/input PWM motor control Jumper block for selection of daisy chain or input PWM motor control MC34SB0800 Octal Valve Controller System on Chip TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 8 NXP Semiconductors Getting to Know the Hardware 4.4.1 LED Display The following LEDs are provided as visual output devices for the TWR-SB0800-36EVB: D14 D20 D2 D22 D17 PD_G HD_G Figure 5. LED Locations Table 3. LEDs LED ID Description D2 Indicates when the MC34SB0800 is in Reset or Safe /Normal Mode (Blinking = Reset Mode; ON = Safe/Normal Mode) D14 Indicates when power is being supplied to the MC34SB0800 D17 Indicates when the low-side general purpose driver is in the ON state D20 Indicates when 5.0 V is being supplied to the VCC5 input D22 Indicates when the high-side general purpose driver is in the ON state HD_G Not connected PD_G Not connected TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 9 Getting to Know the Hardware 4.4.2 Test Point Definitions The following tests point are provided for signal analysis of the MC34SB0800 device. TP11 TP2 TP14 TP1 TP12 TP3 TP9 TP4 TP8 TP5 TP7 TP13 TP2 TP10 Figure 6. Test Point Locations Table 4. Test Points Schematic Label Description TP1 DOSV (digital output) signal TP2 DC motor gate driver signal TP3 SPI/Chip Select signal TP4 SPI clock signal TP5 SPI MOSI signal TP6 SPI MISO signal TP7 ADN1 signal (10-bit ADC) TP8 ADN2 signal (10-bit ADC) TP9 ADN3 signal (10-bit ADC) TP10 High-side pre-driver Safe Switch gate signal TP11 VPWR signal TP12 AGND signal TP13 AGND signal TP14 AGND signal TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 10 NXP Semiconductors Getting to Know the Hardware 4.4.3 Connectors Input/output connectors provide the following signals: VCC5 VPWR ADN1 J3 J2 AGND ADN2 SB0800_HSD ADN3 LSD1 LSD5 LSD2 LSD6 LSD3 LSD7 LSD4 LSD8 J4 J6 Motor - HD Motor + LD J1 J8 Figure 7. Connector Locations Table 5. Connectors Name Description J2 VPWR - Power supply inputs for the MC34SB0800 (6.0 V to 36 V) J2 AGND - Ground input for the MC34SB0800 J2 SB0800_HSD - High-side Safe Switch output for the MC34SB0800 J4 LSD1 - Regulated valve driver output 1 for the MC34SB0800 (2.25 A maximum, 5.0 kHz maximum) J4 LSD2 - Regulated valve driver output 2 for the MC34SB0800 (2.25 A maximum, 5.0 kHz maximum) J4 LSD3 - Regulated valve driver output 3 for the MC34SB0800 (2.25 A maximum, 5.0 kHz maximum) J4 LSD4 - Regulated valve driver output 4 for the MC34SB0800 (2.25 A maximum, 5.0 kHz maximum) J3 VCC5 - 5.0 V external digital input to the MC34SB0800 (not required if J5, J10 and J11 select the 5.0 V tower supply) J3 ADIN1 - 10-bit ADC input 1 to the MC34SB0800 (for safety and general purpose external monitoring) J3 ADIN2 - 10-bit ADC input 2 to the MC34SB0800 (for safety and general purpose external monitoring) J3 ADIN3 - 10-bit ADC input 3 to the MC34SB0800 (for safety and general purpose external monitoring) J6 LSD5 - PWM valve driver output 5 for the MC34SB0800 (5.0 A maximum; 5.0 kHz maximum) TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 11 Getting to Know the Hardware Table 5. Connectors (continued) Name Description J6 LSD6 - PWM valve driver output 6 for the MC34SB0800 (5.0 A maximum; 5.0 kHz maximum) J6 LSD7 - PWM valve driver output 7 for the MC34SB0800 (5.0 A maximum; 5.0 kHz maximum) J6 LSD8 - PWM valve driver output 8 for the MC34SB0800 (5.0 A maximum; 5.0 kHz maximum) J8 HD - High-side general purpose driver output for MC34SB0800 with LED indicator J8 LD - Low-side general purpose driver output for MC34SB0800 with LED indicator 4.4.4 Jumper Definitions Figure 8 and Table 6 define the jumper positions and explains their functions. (The default settings are shown in bold.) J11 J13 J10 J5 J9 J7 Figure 8. Jumper Locations TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 12 NXP Semiconductors Getting to Know the Hardware . Table 6. Jumpers Jumper Description Setting Connection J5 Selects between Tower 5.0 V supply and external 5.0 V supply 1–2 External 5.0 V supply 2–3 Tower 5.0 V supply J7 Connect/Disconnect LED as the general purpose low-side driver load 1–2 LED connected J9 Connect/Disconnect LED as the general purpose high-side driver load J10 Selects between digital voltage level of 5.0 V and 3.3 V 1–2 2–3 3.3 V digital voltage level J11 Selects between digital under voltage level of 5.0 V and 3.3 V 1–2 5.0 V digital under-voltage level 2–3 3.3 V digital under-voltage level J13 Selects compatibility settings when using additional tower boards Not connected 1–2 Not connected Multiple LED disconnected LED connected LED disconnected 5.0 V digital voltage level See Section 5.2 "Tower Board Settings" TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 13 Setting up the Hardware 5 Setting up the Hardware 5.1 Configuring the Hardware Table 7 shows jumper settings for various MCU Tower Boards. Figure 9 shows a typical configuration using the TWR-KL25Z48M and the jumper settings outlined in red in Table 7. Table 7. MCU Tower Board TWR-KL25Z48M Jumper Settings TWR-KL25Z48M TWR-KV31F120M TWR-KV10Z32 TWR-K64F120M TWR-K20 TWR-K22F120 TWR-K70 RSTB GPIO1 GPIO1 GPIO1 GPIO1 GPIO8 GPIO1 GPIO2 CSB GPIO2 GPIO2 GPIO2 GPIO2 GPIO9 GPIO2 GPIO3 PDI PWM4 PWM4 PWM4 PWM4 PWM4 PWM0 PWM4 In this example, J5 is set to connect to an external 5.0 V power supply, J10 selects 3.3 V as the digital voltage level and J11 sets the digital under-voltage level at 3.3 V. J7 and J9 connect the LED low-side and high-side driver loads. Figure 9. Configuration Example TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 14 NXP Semiconductors Setting up the Hardware 5.2 Tower Board Settings A jumper block (J13) on the TWR-SB0800-36EVB provides a means of configuring the board for use with additional MCUs. The J13 jumper settings define the routing of all SPI signals, the reset signal from the MCU and the PWM motor control signal. In addition, jumper J10 allows you to select between either 3.3 V or 5.0 V depending on the requirement of the MCU being used. Make sure that you set jumper J10 to the proper voltage level and that you set the jumpers on J13 to appropriate positions for the selected MCU. Check the schematic of each tower elevator board to assure that all signals are correctly connected. Figure 10 shows the selection options on the TWR-SB0800-36EVB. J13 GPIO1 SB0800_RESET GPIO2 GPIO8 GPIO9 SB0800_CSB GPIO8 GPIO2 1 3 5 7 9 11 13 15 17 19 2 4 6 8 10 12 14 16 18 20 PWM0 PWM4 PWM1 SB0800_ADIN1 PWM5 GPIO8 GPIO3 HDR_2X10 Figure 10. Jumpers for IO selection Blue text indicates signals coming from the MC34SB0800 of the TWR-SB0800-36EVB. Red text indicates signals coming from the tower elevator board (Primary and Secondary). Table 8 shows J13 jumper settings for compatible tower boards. These settings are important because the Reset (RSTB) and Chip Select (CSB) signals must be routed to MCU IO header positions that can handle such signals. Note that the ADIN1 pin can be used either to directly control the Pump Motor Pre-Driver or to measure external voltage. Table 8. Jumper Settings for Compatible Tower Boards TWR-KL25Z48M TWR-KV31F120M TWR-KV10Z32 TWR-K64F120M TWR-K20 TWR-K22F120 TWR-K70 RSTB GPIO1 GPIO1 GPIO1 GPIO1 GPIO8 GPIO1 GPIO2 CSB GPIO2 GPIO2 GPIO2 GPIO2 GPIO9 GPIO2 GPIO3 ADIN1 PWM4 PWM4 PWM4 PWM4 PWM4 PWM0 PWM4 5.3 Step-by-step Instructions for Setting Up the Hardware To perform the demonstration examples, the following connections and setup must be performed: 1. Mount the TWR-SB0800-36EVB and TWR-KL25Z48M board firmly to the tower elevator connectors. Notice that, on the board, the edge connector with the white stripe must be matched with the white connector on the primary elevator module. 2. Connect the positive wire from the power supply to the positive "VPWR" terminal on connector J2 of the TWR-SB0800-36EVB. Connect the negative wire from the power supply to the "AGND" terminal on connector J2. 3. Check to assure that all jumpers are in the default position on the TWR-SB0800-36EVB and the TWR-KL25Z48M board (refer to the tower MCU board User Guide). 4. Attach a USB mini-cable between the PC and the USB mini-plug connector on the TWR-KL25Z48M board. This cable serves as the VCC5 supply and the communication link between the tower boards platform and the PC. TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 15 SB0800_P53_CFG VCC5 SB0800_LSD_8 SB0800_LSD_7 SB0800_LSD_6 SB0800_LSD_5 SB0800_LSD_4 SB0800_LSD_3 SB0800_LSD_2 SB0800_LSD_1 TP1 AGND DNP VPWR 38 39 40 41 42 43 44 45 11 12 9 10 7 8 5 6 33 31 32 24 LSD8_1 LSD8_2 LSD7_1 LSD7_2 LSD6_1 LSD6_2 LSD5_1 LSD5_2 LSD4_1 LSD4_2 LSD3_1 LSD3_2 LSD2_1 LSD2_2 LSD1_1 LSD1_2 HD_D HD_G HD_S CP AGND RST NC_3 NC_17 NC_19 NC_20 NC_21 NC_22 NC_23 NC_27 NC_34 NC_35 NC_36 NC_47 NC_58 NC_59 NC_60 NC_61 NC_62 NC_63 PD_D PD_G PD_S ADIN1 ADIN2 ADIN3 HS LD CS SCLK SI SO MC34SB0800AE 3 17 19 20 21 22 23 27 34 35 36 47 58 59 60 61 62 63 30 28 29 26 TP7 DNP TP8 50 DNP TP9 49 DNP 48 18 TP3 1 DNP TP4 16 DNP TP5 14 DNP TP6 15 DNP 57 U1 C3 0.22UF 24 "CP" & pin 25 "VPWR" C5 must be placed closed to pin about wires size on Layout. LSDx drain 5A maximum, be carefull Note : 0.22uF C7 C6 1uF C5 0.22UF SB0800_HD_D SB0800_HD_G SB0800_HD_S VPWR DOSV AGND 56 DOSV 64 P53_CFG 52 VINT_A 53 VINT_D R1 0 AGND SB0800_PD_D SB0800_PD_G SB0800_PD_S SB0800_ADIN1 SB0800_ADIN2 SB0800_ADIN3 SB0800_HS SB0800_LD SB0800_CSB SCLK0 MOSI0 MISO0 R3 10K VCC5 A 4 1 C8 1000PF SW1 3 PB switch 2 SB0800_RESET DOSV AGND VCC5 VPWR SB0800_RESET DOSV AGND VCC5 VPWR In/Out Signal SB0800_RESET D2 GREEN R4 1K AGND C AGND 4 R11 A 100 C GDZ15B-E3-08 D7 D6 GDZ15B-E3-08 SB0800_HD_S 100 DNP SB0800_HSD RJK0301DPB Q2 0.1uF 10uF C10 C9 Current can raise at 50A peak (for short circuit tests) and 30 A in DC, be aware about wire size on Layout. Note : ORANGE D8 R10 1.8K SB0800_HD_G R9 TP10 100 SB0800_HD_D R8 VPWR HSD Function - 20A - 5 1 2 3 C2 0.22UF A C C A AGND ORANGE D4 R6 1.8K SB0800_PD_G TP2 4 A C R7 2K GDZ15B-E3-08 D3 D1 GDZ15B-E3-08 DNP 2K R2 AGND 0.1UF D5 SS2H10 RJK0301DPB Q1 10uF C4 C1 J1 B A CON_2_TB Motor Pump - 2 1 Motor Pump + AGND and 10 A in DC, be aware about wire size on Layout. Current can raise at 70A peak during 2ms Note : AGND SB0800_PD_S R5 100 SB0800_PD_D VPWR Motor Function - 40A - C A 25 55 VPWR VCC5 GND_P0 GND_P1 GND_P2 GND_P3 GND_P4 2 4 13 37 46 GND_A 51 GND_D 54 EPAD 65 A C 5 1 2 3 16 C 6 A AGND Schematic Schematic Figure 11. Schematic Part 1 TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors CON_VCC5 SB0800_ADIN3 SB0800_ADIN2 SB0800_ADIN1 J8 B A 1 2 CON_2_TB R15 1.8K HDR 1X2 TH J9 J7 HDR 1X2 TH AGND ORANGE D22 1 2 2 1 ORANGE D17 R13 1.8K VPWR SB0800_HS SB0800_LD Low Side Driver Connectors J3 1 2 3 4 J6 J4 1 2 3 4 CON_4_TB CON_4_TB 4 3 2 1 AGND SS2H10 D9 C C11 2200PF SS2H10 D12 A C A AGND AGND AGND SS2H10 D16 A C17 2200PF SS2H10 D18 A C16 2200PF C C C15 2200PF SS2H10 D15 A C SB0800_LSD_8 AGND AGND C21 2200PF A C20 2200PF SS2H10 D21 C C19 2200PF SS2H10 SB0800_LSD_7 D19 AGND A C SB0800_LSD_6 SB0800_LSD_5 SB0800_LSD_4 C14 2200PF SS2H10 SB0800_LSD_3 AGND D13 A C SB0800_LSD_2 SB0800_LSD_1 SB0800_HSD AGND D20 BLUE R14 1K 3 Pin 1 & 2 2 & 3 ELE_PS_SENSE_1 DOSV 5V 3.3V TWR_VCC3V3 Pin 1 & 2 2 & 3 J11 AGND DNP SB0800_P53_CFG P53_CFG 3.3V 5V AGND 1 2 R16 10K VCC5 VCC External VCC5 Tower VCC5 D14 GREEN R12 1.8K VPWR TP11 TP12TP13TP14 DNP DNP DNP AGND C12 10uF 3 DOSV Pin 1 & 2 2 & 3 C13 0.1uF HDR_1X3 R17 0 VCC5 TWR_VCC5 VCC5 - Supply STPS2H100AY D11 2 VCC5 C 1 HDR_1X3 J10 C18 0.1uF J5 HDR_1X3 D10 SUPPLY STPS2H100AY A AGND SB0800_HSD Digital Supply AGND CON_VCC5 J2 1 2 3 4 CON_4_TB 3 MC34SB0800 LSD_1 to LSD_8 1 C A CON_4_TB A C A C 2 A C A NXP Semiconductors C VCC5 & ADIN Connector Schematic Figure 12. Schematic Part 2 TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 17 18 SCLK0 MISO0 MOSI0 ELE_PS_SENSE_1 AGND TWR_VCC3V3 AGND AGND PWM5 PWM4 TWR_VCC3V3 AGND AGND GPIO1 GPIO2 GPIO3 AGND TWR_VCC5 AGND TWR_VCC3V3 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62 B63 B64 B65 B66 B67 B68 B69 B70 B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 B81 B82 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 J12A PCI EXPRESS TOWER SYSTEM ETH_COL_1 ETH_RXER_1 ETH_TXCLK_1 ETH_TXEN_1 ETH_TXER_1 ETH_TXD3_1 ETH_TXD2_1 ETH_TXD1_1 ETH_TXD0_1 GPIO1/RTS1 GPIO2/SDHC_D1 GPIO3 CLKIN0 CLKOUT1 GND_4 AN7 AN6 AN5 AN4 GND_5 DAC1 TMR3 TMR2 GPIO4 3.3V_2 PWM7 PWM6 PWM5 PWM4 CANRX0 CANTX0 1WIRE SPI0_MISO/IO1 SPI0_MOSI/IO0 SPI0_CS0 SPI0_CS1 SPI0_CLK GND_6 SCL1 SDA1 GPIO5/SPI0_HOLD/IO3 USB0_DP_PDOWN USB0_DM_PDOWN IRQ_H IRQ_G IRQ_F IRQ_E IRQ_D IRQ_C IRQ_B IRQ_A EBI_ALE/EBI_CS1 EBI_CS0 GND_7 EBI_AD15 EBI_AD16 EBI_AD17 EBI_AD18 EBI_AD19 EBI_R/W EBI_OE EBI_D7 EBI_D6 EBI_D5 EBI_D4 EBI_D3 EBI_D2 EBI_D1 EBI_D0 GND_8 3.3V_3 5V_1 GND_1 3.3V_1 ELE_PS_SENSE_1 GND_2 GND_3 SDHC_CLK/SPI1_CLK SDHC_D3/SPI1_CS1 SDHC_D3/SPI1_CS0 SDHC_CMD/SPI1_MOSI SDHC_D0/SPI1_MISO PRIMARY ETH_CRS ETH_MDC_1 ETH_MDIO_1 ETH_RXCLK_1 ETH_RXDV_1 ETH_RXD3_1 ETH_RXD2_1 ETH_RXD1_1 ETH_RXD0_1 SSI_MCLK SSI_BCLK SSI_FS SSI_RXD SSI_TXD GND_12 AN3 AN2 AN1 AN0 GND_13 DAC0 TMR1 TMR0 GPIO6 3.3V_6 PWM3 PWM2 PWM1 PWM0 RXD0 TXD0 RXD1 TXD1 VSSA VDDA VREFA1 VREFA2 GND_14 GPIO14 GPIO15 GPIO16 GPIO17 USB0_DM USB0_DP USB0_ID USB0_VBUS TMR7 TMR6 TMR5 TMR4 RSTIN RSTOUT CLKOUT0 GND_15 EBI_AD14 EBI_AD13 EBI_AD12 EBI_AD11 EBI_AD10 EBI_AD9 EBI_AD8 EBI_AD7 EBI_AD6 EBI_AD5 EBI_AD4 EBI_AD3 EBI_AD2 EBI_AD1 EBI_AD0 GND_16 3.3V_7 5V_2 GND_9 3.3V_4 3.3V_5 GND_10 GND_11 SCL0 SDA0 GPIO9/CTS1 GPIO8/SDHC_D2 GPIO7/SD_WP_DET A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 A33 A34 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 A56 A57 A58 A59 A60 A61 A62 A63 A64 A65 A66 A67 A68 A69 A70 A71 A72 A73 A74 A75 A76 A77 A78 A79 A80 A81 A82 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 AGND TWR_VCC3V3 AGND AGND PWM1 PWM0 TWR_VCC3V3 AGND AGND GPIO9 GPIO8 AGND TWR_VCC5 AGND TWR_VCC3V3 GPIO2 GPIO8 GPIO9 GPIO2 GPIO8 GPIO1 1 3 5 7 9 11 13 15 17 19 2 4 6 8 10 12 14 16 18 20 HDR_2X10 J13 AGND TWR_VCC5 TWR_VCC3V3 GPIO3 PWM5 GPIO8 PWM4 PWM1 PWM0 SB0800_ADIN1 Allows to adress several IO of MCU Note: SB0800_CSB SB0800_RESET AGND TWR_VCC5 TWR_VCC3V3 AGND TWR_VCC3V3 AGND AGND TWR_VCC3V3 AGND AGND AGND TWR_VCC5 AGND TWR_VCC3V3 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30 D31 D32 D33 D34 D35 D36 D37 D38 D39 D40 D41 D42 D43 D44 D45 D46 D47 D48 D49 D50 D51 D52 D53 D54 D55 D56 D57 D58 D59 D60 D61 D62 D63 D64 D65 D66 D67 D68 D69 D70 D71 D72 D73 D74 D75 D76 D77 D78 D79 D80 D81 D82 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 J12B PCI EXPRESS TOWER SYSTEM ETH_COL_2 ETH_RXER_2 ETH_TXCLK_2 ETH_TXEN_2 GPIO18 GPIO19/SDHCD4 GPIO20/SDHCD5 ETH_TXD1_2 ETH_TXD0_2 ULPI_NXT/USB1_DM ULPI_DIR/USB1_DP ULPI_D5/USB2_DM ULPI_D6/USB2_DP ULPI_D7 GND_20 LCD_HSYNC/LCD_P24 LCD_VSYNC/LCD_P25 AN13 AN12 GND_21 LCD_CLK/LCD_P26 TMR11 TMR10 GPIO21 3.3V_9 PWM15 PWM14 PWM13 PWM12 CANRX1 CANTX1 GPIO22 LCD_OE/LCD_P27 LCD_D0/LCD_P0 LCD_D1/LCD_P1 LCD_D2/LCD_P2 LCD_D3/LCD_P3 GND_22 GPIO23 GPIO24 LCD_D12/LCD_P12 LCD_D13/LCD_P13 LCD_D14/LCD_P14 IRQ_P/SPI2_CS2 IRQ_O/SPI2_CS3 IRQ_N IRQ_M IRQ_L IRQ_K IRQ_J IRQ_I LCD_D18/LCD_P18 LCD_D19/LCD_P19 GND_23 EBI_AD20/LCD_P42 EBI_AD21/LCD_P43 EBI_AD22/LCD_P44 EBI_AD23/LCD_P45 EBI_AD24/LCD_P46 EBI_AD25/LCD_P47 EBI_AD26/LCD_P48 EBI_AD27/LCD_P49 EBI_AD28/LCD_P50 EBI_AD29/LCD_P51 EBI_AD30/LCD_P52 EBI_AD31/LCD_P53 LCD_D20/LCD_P20 LCD_D21/LCD_P21 LCD_D22/LCD_P22 GND_24 3.3V_10 5V_3 GND_17 3.3V_8 ELE_PS_SENSE_2 GND_18 GND_19 SPI2_CLK SPI2_CS1 SPI2_CS0 SPI2_MOSI SPI2_MISO SECONDARY GPIO26 ETH_MDC_2 ETH_MDIO_2 ETH_RXCLK_2 ETH_RXDV_2 GPIO27/SDHCD6 GPIO28/SDHCD7 ETH_RXD1_2 ETH_RXD0_2 ULPI_D0/USB3_DM ULPI_D1/USB3_DP ULPI_D2/USB4_DM ULPI_D3/USB4_DP ULPI_D4 GND_28 AN11 AN10 AN9 AN8 GND_29 GPIO29 TMR9 TMR8 GPIO30 3.3V_13 PWM11 PWM10 PWM9 PWM8 RXD2/TSI0 TXD2/TSI1 RTS2/TSI2 CTS2/TSI3 RXD3/TSI4 TXD3/TSI5 RTS3/TSI6 CTS3/TSI7 GND_30 LCD_D4/LCD_P4 LCD_D5/LCD_P5 LCD_D6/LCD_P6 LCD_D7/LCD_P7 LCD_D8/LCD_P8 LCD_D9/LCD_P9 LCD_D10/LCD_P10 LCD_D11/LCD_P11 TMR16 TMR15 TMR14 TMR13 LCD_D15/LCD_P15 LCD_D16/LCD_P16 LCD_D17/LCD_P17 GND_31 EBI_BE_32_24/LCD_P28 EBI_BE_23_16/LCD_P29 EBI_BE_15_8/LCD_P30 EBI_BE_7_0/LCD_P31 EBI_TSIZE0/LCD_P32 EBI_TSIZE1/LCD_P33 EBI_TS/LCD_P34 EBI_TBST/LCD_P35 EBI_TA/LCD_P36 EBI_CS4/LCD_P37 EBI_CS3/LCD_P38 EBI_CS2/LCD_P39 EBI_CS1/LCD_P40 GPIO31/LCD_P41 LCD_D23/LCD_P23 GND_32 3.3V_14 5V_4 GND_25 3.3V_11 3.3V_12 GND_26 GND_27 SCL2 SDA2 GPIO25 ULPI_STOP ULPI_CLK C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C56 C57 C58 C59 C60 C61 C62 C63 C64 C65 C66 C67 C68 C69 C70 C71 C72 C73 C74 C75 C76 C77 C78 C79 C80 C81 C82 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 AGND AGND AGND TWR_VCC3V3 AGND AGND TWR_VCC3V3 AGND TWR_VCC5 AGND TWR_VCC3V3 Schematic Figure 13. Schematic Part 3 TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors Board Layout 7 Board Layout 7.1 Silkscreen TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 19 Board Bill of Materials 8 Board Bill of Materials Table 9. Bill of Materials(1) Item Qty Schematic Label Value Description Part Number IC VALVES AND PUMP CONTROLLER 3.3 V / 5.0 V LQFP64 MC34SB0800AE Assy Opt Freescale Components 1 1 U1 Active Components 2 2 Q1, Q2 TRAN NMOS PWR 60 A 30 V LFPAK5 RJK0301DPB-00-J0 4 D1, D3, D6, D7 DIODE ZNR 5 MA 15V 0.2 W AEC-Q101 SOD-323 GDZ15B-E3-08 4 2 D2, D14 GREEN LED GRN SGL 30 MA SMT 0805 LTST-C171KGKT 5 2 D4, D8 ORANGE LED OR SGL 30 MA 0805 SMT APHCM2012SECK-F01 6 9 D5, D9, D12, D13, D15, D16, D18, D19, D21 SS2H10 DIODE SCH RECT 2 A 100 V DO-214AA SS2H10-E3/52T 7 2 D10, D11 DIODE PWR RECT SCH 2 A 100 V AEC-Q101 SMA STPS2H100AY 8 2 D17, D22 ORANGE LED OR SGL 30 MA 0805 SMT APHCM2012SECK-F01 9 1 D20 BLUE LED BLUE SGL 30 mA 2.6 V 0603 UT-692NB Use reference PSMN1R8-40YLC Diodes 3 (2) Capacitors 10 1 C1 0.1 F CAP CER 0.1 F 50 V 10% X7R 0603 GRM188R71H104KA93D 11 3 C2, C3, C5 0.22 F CAP CER 0.22 F 50 V 5% X7R 1206 C1206C224J5RACTU 12 3 C4, C9, C12 10 F CAP CER 10 F 50 V 10% X7S AEC-Q200 1210 GCM32EC71H106KA03 13 1 C6 1 F CAP CER 1 F 25 V 10% X7R 0603 0603X105K250SNT 14 1 C7 0.22 F CAP CER 0.22 F 100 V 20% X7S 0805 C2012X7S2A224M/SOFT 15 1 C8 1000 pF CAP CER 1000 pF 25 V 5% C0G CC0603 C0603C102J3GAC 16 3 C10, C13, C18 0.1 F CAP CER 0.1 F 50 V 5% C0G AEC-Q200 1206 CGA5L2C0G1H104J160 AA 17 8 C11, C14, C15, C16, C17, C19, C20, C21 2200 pF CAP CER 2200 pF 50 V 5% X7R 0805 MCCE222J2NRTF RES MF ZERO 1/10 W -- AEC-Q200 0603 CRCW06030000Z0EA (2) Replace by a strap or 0 ohm resistor Resistors 18 1 R1 0 19 2 R2, R7 2 RES MF 2 1/8 W 1% 0805 20 2 R3, R16 10 RES MF 10 1/4 W 5% 1206 CR1206JW103ELF 21 2 R4, R14 1 RES MF 1 1/10 W 0.5% 0603 MCT06030C1001DP500 CR0805-FX-2001ELF 22 4 R5, R8, R9, R11 100 RES MF 100 1/10 W 1% AEC-Q200 0603 CRCW0603100RFKEA 23 2 R6, R10 1.8 RES MF 1.8 1/10 W 5% 0603 WR06X182JTL 24 3 R12, R13, R15 1.8 RES MF 1.8 1/10 W 5% 0603 WR06X182JTL 25 1 R17 0 RES MF ZERO 1/10W -- AEC-Q200 0603 CRCW06030000Z0EA (2) (2) Switches, Connectors, Jumpers and Test Points 26 2 J1, J8 CON_2_TB CON 1X2 TB TH 5 MM SP 394H SN CTB5000/2 27 4 J2, J3, J4, J6 CON_4_TB CON 1X4 TB TH 5 MM SP 394H SN 282836-4 28 2 J5, J11 HDR_1X3 HDR 1X3 TH 100 MIL SP 374H AU 826629-3 Place jumper on pin 2–3 29 2 J7, J9 HDR 1X2 TH HDR 1X2 TH 100 MIL SP 339H AU 98L TSW-102-07-G-S Place jumper on pin 1–2 30 1 J10 HDR_1X3 HDR 1X3 TH 100 MIL SP 374H AU 826629-3 Place jumper on pin 1–2 31 1 J12 PCI EXPRESS TOWER SYSTEM CON DUAL 2X82 Edge PCI Express SMT 1MM SP 591H FOR TOWER SYSTEM NOT A PART TO ORDER EDGE PCI EXPRESS 164 TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 20 NXP Semiconductors Board Bill of Materials Table 9. Bill of Materials(1) Item Qty Schematic Label Value Description Part Number Assy Opt 32 1 J13 HDR_2X10 HDR 2X10 SMT 50 MIL SP 251H AU FTSH-110-01-L-DV-K Place jumpers on pin 1–3 and on pin 17–19 33 1 SW1 PB switch SW SMT 4.0 MM FMS 0.1A MAX 16V MAX ROHS COMPLIANT 7914J-1-000E 14 TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP13, TP14 TEST POINT WHITE TEST POINT WHITE 40 MIL DRILL 180 MIL TH 109L 5002 34 (2) Notes 1. Freescale does not assume liability, endorse, or warrant components from external manufacturers are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer’s responsibility to validate their application. 2. Do not populate TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 21 References 9 References Following are URLs where you can obtain information on related NXP products and application solutions: NXP.com Support Pages Description URL TWR-SB0800-36EVB Tool Summary Page www.nxp.com/TWR-SB0800-36EVB MC34SB0800 Product Summary Page www.nxp.com/MC34SB0800 Tower System Tower System Modular Development www.nxp.com/tower Board Platform TWR-KL25Z48M Tool Summary Page www.nxp.com/TWR-KL25Z48M K20D72M Tool Summary Page www.nxp.com/K20D72M KV13F120M Tool Summary Page www.nxp.com/KV31F120M Kinetis Design Studio Software www.nxp.com/kinetis CodeWarrior Software www.nxp.com/codewarrior 9.1 Support Visit www.nxp.com/support for a list of phone numbers within your region. 9.2 Warranty Visit www.nxp.com/warranty for a list of phone numbers within your region. TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 22 NXP Semiconductors Revision History 10 Revision History Revision 1.0 Date 1/2016 Description of Changes • Initial release TWR-SB0800-36EVB Tower System Platform, Rev. 1.0 NXP Semiconductors 23 How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale products. Home Page: nxp.com There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based Web Support: nxp.com/support Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no on the information in this document. warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: www.nxp.com/terms-of-use.html. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SMARTMOS is a trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © NXP Semiconductors N.V. 2016. All rights reserved. Document Number: KTTWRSB0800-36EVBUG Rev. 1.0 1/2016