Linear Regulator Application Information IC Product Name BD00HA5WEFJ Topology LDO Linear Regulator Type Voltage source Input Output 1 4.5V to 8.0V 1.8V, 500mA *1 2 4.5V to 8.0V 2.5V, 500mA *1 3 4.5V to 8.0V 3.0V, 500mA *1 4 4.5V to 8.0V 3.3V, 500mA *1 5 6.9V to 8.0V 6.0V, 500mA *1 *1 Not to exceed power dissipation. www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 1/4 27.May.2015 Rev.001 Application Note BD00HA5WEFJ ■ Typical Application Circuit U1 BD00HA5WEFJ VIN 8 VCC VO 1 7 ＮＣ FB 2 VOUT C1 9 EPAD R1 6 NC EN 5 ＥＮ GND 3 C2 R2 NC 4 ■ EN terminal setting Terminal state 2.4V ～ 8.0V 0V ～ 0.8V IC operation Normal operation Power down ■ Output voltage setting 0.8 Input/output voltage conditions are required to satisfy the following equations: 1.5 ~ 0.9 0.9 at 500 7.0 The use of resistors with R1 R2=1kΩ to 90kΩ recommended. www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 2/4 27.May.2015 Rev.001 Application Note BD00HA5WEFJ ■ Bill of Materials 1. VO=1.8V (VIN =4.5V to 8.0V) Count Reference Designator Type Value Description Manufacturer Part Number Manufacturer Configuration (mm) 1 C1 Ceramic Capacitor 2.2µF 16V, B, ±10% GRM219B31C225KA87 MURATA 2012 1 C2 Ceramic Capacitor 2.2µF 6.3V, B, ±10% GRM188B30J225KE18 MURATA 1608 1 R1 Resistor 15kΩ 0.063W, 50V, 1% MCR01MZPF1502 ROHM 1005 1 R2 Resistor 12kΩ 0.063W, 50V, 1% MCR01MZPF1202 ROHM 1005 1 U1 IC - LDO Linear Regulator BD00HA5WFEJ ROHM HTSOP-J8 Manufacturer Configuration (mm) 2. VO=2.5V (VIN =4.5V to 8.0V) Count Reference Designator Type Value Description Manufacturer Part Number 1 C1 Ceramic Capacitor 2.2µF 16V, B, ±10% GRM219B31C225KA87 MURATA 2012 1 C2 Ceramic Capacitor 2.2µF 6.3V, B, ±10% GRM188B30J225KE18 MURATA 1608 1 R1 Resistor 51kΩ 0.063W, 50V, 1% MCR01MZPF5102 ROHM 1005 1 R2 Resistor 24kΩ 0.063W, 50V, 1% MCR01MZPF2402 ROHM 1005 1 U1 IC - LDO Linear Regulator BD00HA5WFEJ ROHM HTSOP-J8 Manufacturer Configuration (mm) 3. VO=3.0V (VIN =4.5V to 8.0V) Count Reference Designator Type Value Description Manufacturer Part Number 1 C1 Ceramic Capacitor 2.2µF 16V, B, ±10% GRM219B31C225KA87 MURATA 2012 1 C2 Ceramic Capacitor 2.2µF 10V, B, ±10% GRM219B11A225KA01 MURATA 2012 1 R1 Resistor 33kΩ 0.063W, 50V, 1% MCR01MZPF3302 ROHM 1005 1 R2 Resistor 12kΩ 0.063W, 50V, 1% MCR01MZPF1202 ROHM 1005 1 U1 IC - LDO Linear Regulator BD00HA5WFEJ ROHM HTSOP-J8 Manufacturer Configuration (mm) 4. VO=3.3V (VIN =4.5V to 8.0V) Count Reference Designator Type Value Description Manufacturer Part Number 1 C1 Ceramic Capacitor 2.2µF 16V, B, ±10% GRM219B31C225KA87 MURATA 2012 1 C2 Ceramic Capacitor 2.2µF 10V, B, ±10% GRM219B11A225KA01 MURATA 2012 1 R1 Resistor 7.5kΩ 0.063W, 50V, 1% MCR01MZPF7501 ROHM 1005 1 R2 Resistor 2.4kΩ 0.063W, 50V, 1% MCR01MZPF2401 ROHM 1005 1 U1 IC - LDO Linear Regulator BD00HA5WFEJ ROHM HTSOP-J8 Manufacturer Configuration (mm) MURATA 2012 5. VO=6.0V (VIN =6.9V to 8.0V) Count Reference Designator Description Manufacturer Part Number Type Value Ceramic Capacitor 2.2µF 16V, B, ±10% GRM219B31C225KA87 2 C1, C2 1 R1 Resistor 13kΩ 0.063W, 50V, 1% MCR01MZPF1302 ROHM 1005 1 R2 Resistor 2kΩ 0.063W, 50V, 1% MCR01MZPF2001 ROHM 1005 1 U1 IC - LDO Linear Regulator BD00HA5WFEJ ROHM HTSOP-J8 www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 3/4 27.May.2015 Rev.001 Application Note BD00HA5WEFJ ■ Precautions for use (1) This document provides the BOM for evaluation boards. Small parts can also be selected for resistor, and capacitor. (2) When miniaturizing a resistor, consider decrease in rated power and withstand voltage. (3) When miniaturizing a ceramic capacitor, consider decrease in withstand voltage. In addition, the capacity may be decreased by DC bias characteristics, and the desired characteristics may not be obtained. (4) If ceramic capacitor models differ even when they have the same capacity and withstand voltage, the capacity may be decreased by DC bias characteristics depending on the model, and desired characteristics may not be obtained. Be sure to check the DC bias characteristics. (5) This circuit constant is the value for our evaluation board. It may be necessary to adjust the constant for the actual board. Carry out suitable evaluations. www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. 4/4 27.May.2015 Rev.001 Notice Notes 1) The information contained herein is subject to change without notice. 2) Before you use our Products, please contact our sales representative and verify the latest specifications : 3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the rating specified by ROHM. 4) Examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. 5) The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. 6) The Products specified in this document are not designed to be radiation tolerant. 7) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. 8) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. 9) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. 10) ROHM has used reasonable care to ensur the accuracy of the information contained in this document. However, ROHM does not warrants that such information is error-free, and ROHM shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. 11) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. 12) When providing our Products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act. 13) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. R1102B