Wireless Video Intercom System VL-SWD501BX/UBX Key Features • Wireless Handset: Check visitors on Wireless Monitor, respond promptly and talk from living room, kitchen, everywhere home and while you are doing something else. UP to 6 wireless monitor connectable. Max wireless range is 100m with no obstacles. You can add on repeaters expand the range. UP to 2 DECT repeater connectable. • Large Touch Panel: The main monitor has a large, 5 inch wide screen that clearly shows each visitor's face. You can simply touch the screen to activate an approximate 2x zoom horizontally and vertically. • Electric Lock Release Support for Gate: The gate or door lock can be easily and quickly released even from the second floor of the house. • Wide-Angle Camera: Wide-angle lens covers approximately 170 degrees horizontally and 115 degrees vertically. • SD Card Recording: Automatically record video images of visitors to SD card. It will record up to 3,000 visitors (30 seconds per visitor). (The SD Memory Card is sold separately.) • Wireless Sensor Cameras: By installing the optional DECT Wireless Sensor Camera, you can use human (heat) and motion sensors to monitor locations that you are concerned about. UP to 4 wireless sensor camera connectable. Wiring Schematic Diagram DOORPHONE 1 (Optional lobby station can be connetcted.) MAIN MONITOR MAIN MONITOR STATION A NP <Rear view> LOBBY STATION NP C NP NP Power 12 V AC/DC supply Electric lock NP DOORPHONE 2 220-240 V AC <Rear view> NP NP D C B 24 V DC POWER SUPPLY UNIT NP Electric lock Power supply 12 V AC/DC Electric lock Connection device for option output (A contact) • When using an optional lobby station, this terminal is used by the lobby station. (In this case, connection devices for option output (A concatc) cannot be connected.) NP: Non-polarised NP Power supply 30 V AC/ 24 V DC Wire type and length Wire type*1 Wiring run Diameter Length (Max.) 100 m 130 m 50 m 10 m 20 m According to specification of connected device. Main monitor – Power supply unit B Doorphone – Electric lock*2 Main monitor – Connection device for option output (A contact)*2 C 22 AWG φ 0.65 mm 18 AWG φ 1.0 mm CAT 5 φ 0.5 mm 22 AWG φ 0.65 mm 18 AWG φ 1.0 mm φ 0.5 mm - φ 1.2 mm (24 AWG - 17 AWG) D φ 0.5 mm - φ 1.2 mm (24 AWG - 17 AWG) According to specification of connected device. Wireless sensor camera – Power supply unit – φ 0.65 mm φ 1.0 mm Wireless sensor camera – External sensor – φ 0.5 mm - φ 0.8mm (24 AWG - 20 AWG) 50 m 100 m According to specification of connected device. Must be no longer than 20 m. A Main monitor – Doorphone 22 AWG 18 AWG *1 Type: Single-pair cable with outer sheath (jacket) Conductor: Copper solid • A certified power supply wiring has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply wiring not lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used. *2 When using an electric lock or a connection device for option output (A contact), select a device that meets the following guidelines: • Electric lock connection terminal (S1/S2): - N/O dry closure contact - 12 V AC/DC, less than 1 A • Connection device for option output (A contact) terminal (OUT1/OUT2): - 24 V AC/DC, less than 0.3 A (minimum contact: 5 V DC 1 mA) Accessory Information For the Sub Monitor: AC adaptor × 2 (PNLV226BX [2 pin AC plug] / PNLV226E [3 pin AC plug]), Rechargeable batteries × 2, Charger × 1 For the Door Station: <VL-V554BX> Mounting base × 1 & screw (3.8 mm x 20 mm) × 2, Screw (4 mm x 12 mm) × 4, Name plate × 2, Hex wrench × 1 <VL-V554UBX> Flush mounting box × 1, Screw (4 mm x 25 mm) × 4, Name plate × 2, Hex wrench × 1 For the Main Monitor Station: Power supply unit* (VL-PS241) × 1, Mounting bracket × 1, Cable binder × 1, Screw (4 mm x 16 mm) × 2 *Including AC cable × 2, Cable binder × 1, Screw (4 mm x 40 mm) × 2 Optional Accessories Door Station (Doophone) VL-V554BX VL-V554UBX Wireless Monitor Station (Sub monitor) VL-WD613BX Relative Product Wireless Sensor Camera DECT Repeater Lobby Station VL-WD812BX VL-FKD2BX VL-V590BX VL-V590CX Up to 20 Main monitors connectable Main Monitor Station (Main monitor) VL-MWD501BX Model Composition VL-SWD501BX VL-MWD501BX x 1, VL-WD613BX x 1, VL-V554BX x 1 VL-SWD501UBX VL-MWD501BX x 1, VL-WD613BX x 1, VL-V554UBX x 1 Specifications Model number and name VL-MWD501BX VL-V554BX (Surface mount) VL-V554UBX (Flush mount) VL-WD613BX VL-PS241 Main Monitor Station (Main monitor) Door Station (Doorphone) Wireless Monitor Station (Sub monitor) Main body Charger Power Supply Unit (part) Up to 2 165 mm 21 mm 118 mm 35.8 mm 30 mm Up to 6 100 mm 52 mm 30 mm Dimensions 81 mm 180 mm 169 mm 76 mm 104 mm 173 mm 43 mm 16.5 mm Rechargeable Ni-MH (AAA x 2) Input: 220-240 V AC, 0.2 A, 50/60 Hz Output: 24 V DC, 0.6 A - Standby: Approx. 0.4 W (when the sub monitor is not placed in the charger) During charging: Approx. 1.4 W - 173 x 52 x 30 mm 43 x 81 x 76 mm 104 × 100 × 54 mm 160 g (including the batteries) 0 °C to 40 °C, Up to 90 % RH (Relative Humidity) non condensing Approx. 2.2 inch, colour display 1.88 GHz to 1.90 GHz 70 g (excluding the AC adaptor) 0 °C to 40 °C, Up to 90 % RH (Relative Humidity) non condensing - 215 g 0 °C to 40 °C, Up to 90 % RH (Relative Humidity) non condensing - - - - Horizontally: Approx. 170° Vertically: Approx. 115° - - - Wall mount (mounting bracket supplied) VL-V554BX: surface mount (mounting base supplied) VL-V554UBX: flush mount (flush mounting box supplied) - - - Flame retardant ABS and PS resin IP54*3 / Compliant with IK07 Aluminium and flame retardant PC+PS resin ABS resin ABS resin Flame retardant PC+ABS resin Power source Power supplied by the main monitor 20 V DC, 0.23 A Power consumption Standby: Approx. 1.4 W During operation: Approx. 10 W - 180 x 165 x 21 mm VL-V554BX: 169 x 118 x 30 mm VL-V554UBX: 169 x 118 x 16.5 mm (excluding sections embedded into the wall) 470 g 0 °C to 40 °C, Up to 90 % RH (Relative Humidity) non condensing Approx. 5 inch, wide colour display 1.88 GHz to 1.90 GHz VL-V554BX: 405 g, VL-V554UBX: 345 g -10 °C to 50 °C, Up to 90 % RH (Relative Humidity) non condensing - Rated load: 24 V AC/DC, 0.3 A or lower Minimum applicable load: 5 V DC, 0.001 A (Output when there is a call from the doorphone) - - Installation method IP rating / IK rating External material Dimensions (H x W x D) (Excluding protruding sections) Weight Operating environment Display Frequency Option output (A contact) Viewing angle Model number and name *Indoor use only. AC adaptor (PNLV226BX/PNLV226E) Input: 220-240 V AC, 0.1 A, 50/60 Hz Output: 5.5 V DC, 0.5 A Power supply unit (VL-PS241) 24 V DC, 0.5 A VL-WD812BX VL-FKD2BX Wireless Sensor Camera DECT Repeater Up to 4 118 mm Installing the Main Monitor Up to 2 290 mm 111 mm 39 mm Attach the mounting bracket to the wall securely. Install the mounting bracket on a vertical flat wall. Mounting bracket Vertical, flat wall Hole in wall 60 mm Dimensions 160 mm Power source Power consumption Dimensions (H x W x D) Weight Operating environment Frequency Installation method Transmitting range Minimum illuminance required Image sensor Lighting method Angular field of view (camera angle) Sensor detection range Sensor detection method IP rating Adjustable mounting angles Heat sensor adjustable angles External material 142 mm 94 mm Screws 82 mm Power supply unit (VL-PS241) 24 V DC, 0.4 A AC adaptor (PQLV219BX/PQLV219E) Input: 220-240 V AC, 0.1 A, 50/60 Hz Output: 6.5 V DC, 0.5 A During standby: Approx. 1.5 W During operation: Approx. 4.5 W (when the LED lights are not lit), Approx. 8 W (when the LED lights are lit) During standby: Approx. 1.5 W During operation: Approx. 2.3 W (when transmitting) 160 x 118 x 290 mm (when the camera is front facing and including the wall mount bracket) 82 x 111 x 39 mm 960 g 88 g (excluding the AC adaptor) -20 °C to 50 °C, Up to 90 % RH (Relative Humidity) non condensing 0 °C to 40 °C Up to 90 % RH (Relative Humidity) non condensing 1.88 GHz to 1.90 GHz Wall mount (wall mount bracket supplied) Approx. 100 m (line-of-sight distance from the main monitor) 1 lx*1 0.3 M pixel CMOS 2 white LED lights*2 Horizontal: Approx. 53° Vertical: Approx. 41° 1.88 GHz to 1.90 GHz • Heat sensor (when the surrounding temperature is approx. 20°) Horizontal: Approx. 63°, vertical: Approx. 20°, detection range: Approx. 5 m • Motion detection sensor Horizontal: Approx. 53°, vertical: Approx. 41° Pyroelectric infrared sensor (heat sensor) and motion detection IP54*3 Approx. 100 m (line-of-sight distance from the main monitor) - 50 mm 83.5 mm 7 mm Installing the Doorphone • VL-V554BX (Surface mount) Screw × 2 Mounting base (accessory) 83.5 mm Wall Wire (locally procured) Install the mounting base on a vertical flat wall. • VL-V554UBX (Flush mount) 100 mm Flush mounting box (accessory) - 151 mm 37 mm - - Installing the Wireless Camera Mounting screws (locally procured) × 4 46 mm - Horizontal: ±90°, vertical: facing forward - facing down approx. 60° (adjustable when mounting) - Manually adjustable to 2 angles PC+ABS resin PS resin *1 The minimum illuminance required when the camera’s [Brightness] setting is set to [+3]. *2 Approx. 8.5 lx when 3 m in front of the camera, and approx. 4 lx when 3 m away and 20° to the left or right of the camera. *3 Water resistance is only assured if the camera is installed correctly according to the instructions in the Installation Guide, and appropriate water protection measures are taken. Do not install the camera in areas directly exposed to water or rain. Important – Safety Precaution: carefully read the operating instructions and installation manual before using this product. Screws (accessory) 83.5 mm DC cable Cable access hole • The actual product may vary slightly from photograph. • Weights and dimensions are approximate. • Design and Specifications are subject to change without notice. • These products may be subject to export control regulations. MG-DHPL002EN 1406ITP/ZZZ-BX1