Bulletin PD-20628 rev. A 08/04 MBRB3030CTL SCHOTTKY RECTIFIER 30 Amp Description/Features Major Ratings and Characteristics Characteristics Values Units IF(AV) Rectangular 30 A VRRM 30 V IFSM @ tp = 5 µs sine 1100 A VF @ 15 Apk, TJ = 125°C 0.34 V TJ range - 55 to 150 °C waveform (per leg) This center tap Schottky rectifier has been optimized for very low forward voltage drop, with moderate leakage. The proprietary barrier technology allows for reliable operation up to 150° C junction temperature. Typical applications are in switching power supplies, converters, free-wheeling diodes, and reverse battery protection. 150° C TJ operation Center tap configuration Very low forward voltage drop High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance High frequency operation Guard ring for enhanced ruggedness and long term reliability Case Styles MBRB3030CTL BASE COMMON CATHODE 2 1 2 3 ANODE COMMON ANODE CATHODE 1 2 D2PAK www.irf.com 1 MBRB3030CTL Bulletin PD-20628 rev. A 08/04 Voltage Ratings Parameters VR MBRB3030CTL Max. DC Reverse Voltage (V) 30 VRWM Max. Working Peak Reverse Voltage (V) Absolute Maximum Ratings Parameters IF(AV) Max. Average Forward Current IFSM EAS * See Fig. 5 Values Units (Per Leg) 15 A (Per Device) 30 Max. Peak One Cycle Non-Repetitive 1100 Surge Current (Per Leg) 360 * See Fig. 7 Non-Repetitive Avalanche Energy A Conditions 50% duty cycle @ TC = 121°C, rectangular wave form Following any rated load condition and with 10ms Sine or 6ms Rect. pulse rated V RRM applied TJ = 25 °C, IAS = 3 Amps, L = 2.9 mH 5µs Sine or 3µs Rect. pulse 13 mJ 3 A Values Units 0.44 0.51 0.34 V V V @ 15A @ 30A @ 15A 0.45 V @ 30A 2 mA TJ = 25 °C 183 mA TJ = 125 °C TJ = TJ max. (Per Leg) IAR Repetitive Avalanche Current (Per Leg) Current decaying linearly to zero in 1 µsec Frequency limited by TJ max. VA = 1.5 x VR typical Electrical Specifications Parameters VFM IRM Max. Forward Voltage Drop (Per Leg) * See Fig. 1 (1) Max. Reverse Leakage Current (Per Leg) * See Fig. 2 (1) Conditions TJ = 25 °C TJ = 125 °C VR = rated V R VF(TO) Threshold Voltage 0.22 V rt Forward Slope Resistance 6.76 mΩ CT Max. Junction Capacitance (Per Leg) 2840 pF VR = 5VDC (test signal range 100Khz to 1Mhz) 25°C LS Typical Series Inductance (Per Leg) 8.0 nH Measured lead to lead 5mm from package body 10000 V/ µs dv/dt Max. Voltage Rate of Change (Rated VR) (1) Pulse Width < 300µs, Duty Cycle <2% Thermal-Mechanical Specifications Parameters Values Units TJ Max. Junction Temperature Range -55 to 150 °C Tstg Max. Storage Temperature Range -55 to 150 Conditions °C RthJC Max. Thermal Resistance Junction to Case (Per Leg) 2.0 °C/W DC operation RthJC Max. Thermal Resistance Junction to Case (Per Package) 1.0 °C/W DC operation RthCS Typical Thermal Resistance, Case to Heatsink 0.50 °C/W Mounting surface , smooth and greased (only for TO-220) wt Approximate Weight T Mounting Torque 2 2 (0.07) g (oz.) Min. 6 (5) Max. 12 (10) Kg-cm (Ibf-in) www.irf.com MBRB3030CTL Bulletin PD-20628 rev. A 08/04 Reverse Current - I R(mA) 1000 100 TJ = 150°C 100 125°C 100°C 10 75°C 1 50°C 25°C 0.1 0.01 0 5 10 15 20 25 30 Reverse Voltag e - V R(V) Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage (Per Leg) 10000 TJ= 150°C 10 Junction Capacitance - C T (pF) Instantaneous Forward Current - I F (A) 1000 TJ= 125°C TJ= 25°C 1 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 TJ= 25°C 1000 100 1.8 0 5 10 Forward Voltage Drop - VFM (V) 15 20 25 30 35 Reverse Voltage - V R(V) Fig. 1 - Max. Forward Voltage Drop Characteristics (Per Leg) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage (Per Leg) Thermal Impedanc e Z thJC (°C/ W) 10 1 D = 0.75 D = 0.50 D = 0.33 D = 0.25 D = 0.20 PDM t 0.1 Notes: Single Pulse (Thermal Resistance) 0.01 0.00001 0.0001 0.001 0.01 1 t2 1. Duty fac tor D = t 1/ t 2 2. Peak TJ = PDM x Z thJC+ TC 0.1 1 10 100 t 1 , Rectangular Pulse Duration (Sec onds) Fig. 4 - Max. Thermal Impedance ZthJC Characteristics (Per Leg) www.irf.com 3 MBRB3030CTL Bulletin PD-20628 rev. A 08/04 16 140 Avera ge Power Loss - (Watts) Allowable Case Temperature - (°C) 150 DC 130 Square wave (D = 0.50) 80% Rated V Rap plied 120 110 D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 12 8 DC RMSLimit 4 see note (2) 100 0 5 10 15 20 25 0 30 0 Average Forward Current - I F(AV) (A) Fig. 5 - Max. Allowable Case Temperature Vs. Average Forward Current (Per Leg) Non-Repetitive Surge Current - I FSM (A) 5 10 15 20 25 30 Average Forward Current - I F(AV) (A) Fig. 6 - Forward Power Loss Characteristics (Per Leg) 1000 At Any Rated Load Condition And With Rated V RRM Applied Following Surge 100 10 100 1000 Square Wave Pulse Duration - t 10000 p (microsec) Fig. 7 - Max. Non-Repetitive Surge Current (Per Leg) L IRFP460 DUT Rg = 25 ohm CURRENT MONITOR HIGH-SPEED SWITCH FREE-WHEEL DIODE + Vd = 25 Volt 40HFL40S02 Fig. 8 - Unclamped Inductive Test Circuit (2) Formula used: TC = TJ - (Pd + PdREV) x RthJC ; Pd = Forward Power Loss = IF(AV) x VFM @ (IF(AV) / D) (see Fig. 6); PdREV = Inverse Power Loss = VR1 x IR (1 - D); IR @ VR1 = 10 V 4 www.irf.com MBRB3030CTL Bulletin PD-20628 rev. A 08/04 Outline Table 4.69 (0.18) 4.20 (0.16) 10.16 (0.40) REF. 1.32 (0.05) 1.22 (0.05) 6.47 (0.25) 93° 15.49 (0.61) 6.18 (0.24) 14.73 (0.58) 5.28 (0.21) 2.61 (0.10) 4.78 (0.19) 2.32 (0.09) 0.55 (0.02) 8.89 (0.35) 3X BASE COMMON CATHODE REF. 1.40 (0.055) 1.14 (0.045) 2X 0.46 (0.02) 0.93 (0.37) MINIMUM RECOMMENDED FOOTPRINT 0.69 (0.27) 11.43 (0.45) 2 1 1 2 3 4.57 (0.18) 3 8.89 (0.35) 4.32 (0.17) ANODE COMMON ANODE CATHODE 1 2 2 17.78 (0.70) 0.61 (0.02) MAX. 5.08 (0.20) REF. 3.81 (0.15) 2.08 (0.08) Conform to JEDEC outline D2Pak (SMD-220) Dimensions in millimeters and (inches) 2X 2.54 (0.10) 2X Tape & Reel Information TRR 1.60 (0.063) 1.50 (0.059) 4.10 (0.161) 3.90 (0.153) 1.60 (0.063) 1.50 (0.059) DIA. 0.368 (0.0145) 0.342 (0.0135) FEED DIR ECTION 1.85 (0 .07 3) 1.65 (0 .06 5) 11.60 (0.457) 11.40 (0.449) 15 .42 (0.6 09) 15 .22 (0.6 01) TRL 1.75 (0.069) 10 .90 (0.429) 10 .70 (0.421) 1.25 (0.049) 24 .30 (0 .95 7) 23 .90 (0 .94 1) DIA. 16 .10 (0.634) 4.72 (0.186) 4.52 (0.178) 15 .90 (0.626) FEED DIRECTION 13.50 (0.532) 12.80 (0.504) DIA. 26.40 (1.0 39) 24.40 (0.9 61) SMD-220 Tape & Reel When ordering, indicate the part number, part orientation, and the quantity. Quantities are in multiples 360 (1 4.173) DIA. MAX. 60 (2 .36 2) of 800 pieces per reel for both TRL and TRR. DIA. MIN . Dimensions in millimeters and (inches) www.irf.com 5 MBRB3030CTL Bulletin PD-20628 rev. A 08/04 Ordering Information Table Device Code MBR B 30 30 CT L TRL 1 2 3 4 5 6 7 1 - Schottky MBR Series 2 - B = D2PAK 3 - Current Rating (30 = 30A) 4 - Voltage Rating (30 = 30V) 5 - CT = Center Tap (Dual) 6 - L = Low V F 7 - y none = Tube (50 pieces) y TRL = Tape & Reel (Left Oriented - for D2Pak only) y TRR = Tape & Reel (Right Oriented - for D2Pak only) Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 08/04 6 www.irf.com