SE3002-DC94A Printheads High speed thermal printhead (300 dots / inch) SE3002-DC94A High speed, high quality, and high durability are achieved by using step free structure with high performance partial glaze and highly conductive overcoat layer. SE300*-DC94A series are lined up which can accommodate with all types of barcode labeling printers from Direct to Thermal Transfer, normal to high speed (over 300mm/s). Implementation of ROHM Unique technology, Anti Sticking Treatment, reduces sticking problems (print skip at media feed direction) under the tough print conditions at low print speed, using label media with over coated. zApplications Bar code printer Label printer Packaging printer ATM Ticket printer zFeatures 1) Anti Sticking Treatment reduces sticking problems and achieves high print quality at any environmental conditions. 2) ROHM new technology “STEP FREE” structure will provide, high corrosion resistance, better resistance against scratching damage, high efficiency. 3) Standard glazed components to accommodate thick paper. 4) Using a hard conductive film as a protective film on the heating element offers excellent resistance to electrostatic damage. zDimensions (Unit : mm) DOT No.1 DOT No.640 MAX.φ20 6±0.5 66±0.5 54.208 (Effective print width) MAX.48 MIN.4.3 (3.5) (5.896) MAX.5 #2 #20 CONNECTOR:A #4 #1 CONNECTOR:B #1 MAX.10 φ3 H10 Length 4 Effective Depth 3 (21.3) 17.8±0.2 25±0.5 (36) 7.3±0.3 #19 20±0.3 (13) φ3 H10 Effective Depth 3 7.104±0.3 40±0.3 M3 Effective Depth 3 Note : No heat history control function inside the thermal printhead. External heat history control is required for high speed printing. 1/4 SE3002-DC94A Printheads zEquivalent circuit DOT#640 DOT#1 VH (COM) #640 VDD #321 #320 #1 0.1µF 50V GND BEO STB2 STB1 LATCH REGISTER /LAT CLK SHIFT REGISTER DI2 SHIFT REGISTER DI1 SENS1 SENS2 SENS3 TM TM CONNECTOR DI No. DOT No. STB No. DI2 640 to 321 STB2 640 to 321 DI1 320 to STB1 320 to 1 DOT No. 1 2/4 SE3002-DC94A Printheads zPin assignments No. Circuit No. Circuit No. Circuit 1 VDD 2 BEO 1 VH 3 GND 4 DI2 2 VH 5 N.C. 6 CLK 3 VH 7 LAT 8 GND 4 GND 9 GND 10 DI1 5 GND 11 N.C. 12 GND 6 GND 13 VDD 14 STB2 15 STB1 16 TM 17 TM 18 SENS1 19 SENS2 20 SENS3 zTiming chart Min.45ns CLK Min.30ns Min.10ns DI (DATA IN) BEO Min.100ns Min.50ns Min.12.5µs LAT (LATCH) Min.100ns Min.300ns STB (STROBE) Min.12.5µs Min.12.5µs DRIVER OUT 3/4 SE3002-DC94A Printheads zCharacteristics Symbol Typical Unit Effective printing width − 54.2 mm Dot pitch − 0.0847 mm Total dot number − 640 dots Rave 850 Ω VH 24 V Parameter Average resistance value Applied voltage Applied power PO 0.59 W / dot SLT 0.42 ms Maximum number of dots energized simultaneously − 640 dots Maximum clock frequency − 10 MHz Maximum roller diameter − φ 20 mm Running life / pulse life − 150 / 108 km / pulses Operating temperature − 5 to 45 °C Print cycle 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0