KD3008-CF10A Printheads For Gaming Equipment, ATMs : CF, CG series KD3008-CF10A zApplications Plain-paper printers Low speed ticket vendors Measuring terminal printers zFeatures Utilizing the ideal element structure for each model (CF series: 100mm/s, CG series: 150mm/s) ensures perfect print quality and efficient energy consumption. In addition, the units feature a high-frequency clock, enabling advance control. zDimensions (Unit : mm) 230.5±0.3 (HEATSINK WIDTH) 230 (SUBSTRATE WIDTH) 219.5424 (EFFECTIVE PRINT WIDTH) Dot #2592 Dot #1 2.6±0.1 MAX.20.1 CL RESIN COATING FOR PROTECTION IC No.15 No.1 No.1 No.15 CONNECTOR.B (10.2) 5.1±0.2 CONNECTOR.A 5±0.2 220.5±0.2 2-M3 (EFFECTIVE DEPTH 3) CENTER OF HEAT ELEMENT Rev.A 1/4 KD3008-CF10A Printheads zEquivalent circuit DOT #2592 DOT #1 VH VH GND 2592 1873 1872 1297 1296 721 720 GND 1 Vdd /STB4 /STB1 /STB3 /STB2 LATCH RESISTER DI1 DI2 SHIFT RESISTER SHIFT RESISTER DO1 /LAT DO2 CLK TM ＴHＥＲＭＩＳＴＯＲ 30ｋΩ Ｂ：3950K CONNECTOR B CONNECTOR A zPin assignments CONNECTOR B CONNECTOR A No. Circuit No. Circuit 1 GND 1 VH 2 GND 2 VH 3 GND 3 VH 4 GND 4 VH 5 VDD 5 DI2 6 /STB3 6 DO2 7 /STB4 7 /LAT 8 CLK 8 /STB1 9 DI1 9 /STB2 10 DO1 10 TM 11 VH 11 GND 12 VH 12 GND 13 VH 13 GND 14 VH 14 GND 15 VH 15 GND Rev.A 2/4 KD3008-CF10A Printheads zTiming chart tw CLK CLK(CLOCK) tsetup DI thold DI DI(DATA IN) "High":Black "Low" :White td DO DO(DATA OUT) "High":Black "Low" :White tsetup LAT min.10µsec* thold LAT /LAT(LATCH) "High": Hold "Low":T hrough tw LAT tsetup ST B /STB(STROBE) tdo tdo DRIVER OUT * If delay time for Driver Out can not be secured enough, there is a possibility that VH would fluctuate greatly. Please design the circuit so that VH does not exceed peak voltage (Vp). zCharacteristics Symbol Typical Unit Effective printing width − 219.542 mm Dot pitch − 0.0847 mm Total dot number − 2592 dots Parameter Rave 1250 Ω Applied voltage VH 24.0 V Applied power Average resistance value PO 0.23 W / dot Print cycle SLT 1.11 ms Pulse width TON 0.51 ms Maximum number of dots energized simultaneously − 1296 dots Maximum clock frequency − 16 MHz Maximum roller diameter − φ20.0 mm Running life / pulse life − 50 / 1×108 km / pulses Operating temperature − 5 to 45 °C Rev.A 3/4 KD3008-CF10A Printheads 0.2 180 0.18 160 0.16 0.16 140 0.14 0.14 0.12 0.1 0.25 0.08 0.06 0.12 0.1 0.25 0.08 0.06 0.04 0.04 0.02 0.02 0 0 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 SLT : (ms) Fig.1 Adaptive speed chart RESISTANCE : (kΩ) 0.2 0.18 Supply E0 : (mj / dot) Max. E0 : (mj / dot) zElectrical characteristic curves 120 100 80 60 40 20 0 0 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 SLT : (ms) Fig.2 Maximum energy curve 0 −20 −10 0 10 20 30 40 50 60 70 TEMPERATURE : (°C) Fig. 3 Thermistor curve Rev.A 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0