ROHM MVR21

MVR21
Resistors
Chip trimmer potentiometers
MVR21
zFeatures
1) Extremely small size and light weight facilitate the assembly of light, thinner, and smaller equipment.
2) Close match between wiper and resistive element reduces wiper noise.
3) Ruthenium oxide resistor material, with superb stability and resistance to humidity and the elements, offers the same
outstanding reliability of our existing product (MVR22).
4) Open design for reflow soldering.
5) Cross groove for easy adjustment.
6) Protective film prevents short circuits due to terminal contact.
7) ROHM resistors have approved ISO-9001 / ISO/TS 16949 certification. Design and specifications are subject to
change without notice. Carefully check the specification sheet supplied with the product before using or ordering it.
zRatings
Item
Rated power
Conditions
Specifications
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70˚C.
0.15W (3 / 20W) / element
at 70˚C
POWER LOAD (%)
100
80
60
40
20
0
– 55
0
70
100
125
155
AMBIENT TEMPERATURE ( ˚C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
E : Rated voltage (V)
E= P×R
P : Rated power (W)
R : Nominal resistance (Ω)
Max. operating voltage
50V
Nominal total
resistance range
100 to 2.2MΩ (applicable resistance value : E6 series)
Total
resistance tolerance
±25%
Resistance
variation
B (linear) characteristics
Operating temperature
−55˚C to +155˚C
(recommended resistance value : E3 series)
1/3
MVR21
Resistors
zDimensions (Unit: mm)
Name of part
③
①
⑤
Material
Substrate
Alumina substrate
Resistance paste
Thick film resistive element
Wiper
Metal
2nd Terminal (T2)
Metal and Ni plating and Sn plating
②
1st,3rd Terminals (T1, T3) Metal and Ni plating and SnAgCu solder
Protective film
Insulator
(Unit : mm)
④
A
(B)
2.0 +0.15
−0.05
C
D
(1.35±0.2) 1.5±0.2 2.85±0.15
E
F
0.4 +0.05
1.35
0
G
+0.05
0
0.75
+0.15
−0
H
I
J
K
L
M
N
0.9±0.1
1.0±0.1
0.55±0.1
0.6±0.2
0.75±0.1
1.02±0.1
0.48±0.1
zEquivalent circuit
T1
T3
T2
T : terminal
zPackaging
Reel
Taping
P2
E
F
B0
W
0.4
0.2
0. 8
0 .6
0 .4
D
0.8
B
0.2
A
0.6
φ
D0
P0
K
P1
A0
C
ラベル
Compatible with JEITA standard "EIAJ ET-7200B"
(Unit : mm)
(Unit : mm)
A
φ180
B
0
−3
φ60
+1
0
C
D
9 ± 1.0/−0
φ13 ± 0.2
W
F
E
A0
B0
8.0 ± 0.2 3.5 ± 0.05 1.75 ± 0.1 2.45 ± 0.1 3.2 ± 0.1
D0
P0
φ1.5 + 0.1
0
4.0 ± 0.1
P1
K
P2
4.0 ± 0.1 2.0 ± 0.05
1.8
+0
−0.1
2/3
MVR21
Resistors
zPart No. Explanation
Part No.
1
I
Packaging / Processing specifications
Part No.
Code Processing specifications Packaging specifications
MVR21
IXBR
Reflow soldering
Paper tape (4mm Pitch)
Resistance
tolerance
Reel
Basic ordering
unit(pcs)
φ180mm(7inch)
3,000
N
± 25%
Nominal
resistance
3-digit IEC coding system
Recommended resistance value : E3 series
Applicable resistance value : E6 series
3/3
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2007 ROHM CO.,LTD.
THE AMERICAS / EUPOPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix1-Rev2.0