SA56004X ±1 °C accurate, SMBus-compatible, 8-pin, remote/local digital temperature sensor with overtemperature alarms Rev. 05 — 22 May 2008 Product data sheet 1. General description The NXP Semiconductors SA56004X is an SMBus compatible, 11-bit remote/local digital temperature sensor with overtemperature alarms. The remote channel of the SA56004X monitors a diode junction, such as a substrate PNP of a microprocessor or a diode connected transistor such as the 2N3904 (NPN) or 2N3906 (PNP). With factory trimming, remote sensor accuracy of ±1 °C is achieved. Undertemperature and overtemperature alert thresholds can be programmed to cause the ALERT output to indicate when the on-chip or remote temperature is out of range. This output may be used as a system interrupt or SMBus alert. The T_CRIT output is activated when the on-chip or remote temperature measurement rises above the programmed T_CRIT threshold register value. This output may be used to activate a cooling fan, send a warning or trigger a system shutdown. To further enhance system reliability, the SA56004X employs an SMBus time-out protocol. The SA56004X has a unique device architecture. The SA56004X is available in the SO8, TSSOP8 and HVSON8 packages. SA56004X has 8 factory-programmed device address options. The SA56004X is pin-compatible with the LM86, MAX6657/8, and ADM1032. 2. Features n Accurately senses temperature of remote microprocessor thermal diodes or diode connected transistors within ±1 °C n On-chip local temperature sensing within ±2 °C n Temperature range of −40 °C to +125 °C n 11-bit, 0.125 °C resolution n 8 different device addresses are available for server applications. The SA56004ED with marking code 56004E, and SA56004EDP with marking code 6004E are address compatible with the National LM86, the MAX6657/8 and the ADM1032. n Offset registers available for adjusting the remote temperature accuracy n Programmable under/overtemperature alarms: ALERT and T_CRIT n SMBus 2.0 compatible interface, supports TIMEOUT n Operating voltage range: 3.0 V to 3.6 V n I2C-bus Standard-mode and Fast-mode compatible n SO8, TSSOP8 and HVSON8 packages n Programmable conversion rate (0.0625 Hz to 26 Hz) n Undervoltage lockout prevents erroneous temperature readings n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 3. Applications n n n n n System thermal management in laptops, desktops, servers and workstations Computers and office electronic equipment Electronic test equipment and instrumentation HVAC Industrial controllers and embedded systems 4. Ordering information Table 1. Ordering information Type number[1] SA56004AD Package Name Description Version SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 TSSOP8 plastic thin shrink small outline package; 8 leads; body width 3 mm SOT505-1 HVSON8 plastic thermal enhanced very thin small outline package; no leads; 8 terminals; body 3 × 3 × 0.85 mm SOT782-1 SA56004BD SA56004CD SA56004DD SA56004ED SA56004FD SA56004GD SA56004HD SA56004ADP SA56004BDP SA56004CDP SA56004DDP SA56004EDP SA56004FDP SA56004GDP SA56004HDP SA56004ATK SA56004ETK SA56004FTK [1] There are 8 device slave address options, as described in Table 2. 4.1 Ordering options Table 2. Ordering options Type number Topside mark Device slave address[1] SA56004AD 56004A 1001 000 SA56004ADP 6004A SA56004ATK 6004A SA56004BD 56004B SA56004BDP 6004B 1001 001 SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 2 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Table 2. Ordering options …continued Type number Topside mark Device slave address[1] SA56004CD 56004C 1001 010 SA56004CDP 6004C SA56004DD 56004D SA56004DDP 6004D SA56004ED[2] 56004E SA56004EDP[2] 6004E SA56004ETK[2] 6004E SA56004FD 56004F SA56004FDP 6004F SA56004FTK 6004F SA56004GD 56004G SA56004GDP 6004G SA56004HD 56004H SA56004HDP 6004H 1001 011 1001 100 1001 101 1001 110 1001 111 [1] The device slave address is factory programmed in OTP device address register. [2] The SA56004ED/EDP/ETK has the bus address of the National LM86, MAX6657/8 and the ADM1032. 5. Block diagram SA56004X ONE-SHOT REGISTER VDD LOCAL TEMP SENSOR D+ D− CONTROL LOGIC 11-BIT Σ-∆ A-to-D CONVERTER LOCAL REMOTE MUX ALERT REMOTE OFFSET REGISTER CONFIGURATION REGISTER COMMAND REGISTER CONVERSION REGISTER LOCAL HIGH TEMP THRESHOLD LOCAL TEMP HIGH LIMIT REGISTER LOCAL TEMP DATA REGISTER LOCAL LOW TEMP THRESHOLD LOCAL TEMP LOW THRESHOLD REMOTE TEMP DATA REGISTER REMOTE HIGH TEMP THRESHOLD REMOTE TEMP HIGH LIMIT REG. T_CRIT HYSTERESIS REMOTE LOW TEMP THRESHOLD REMOTE TEMP LOW LIMIT REG. ALERT INTERRUPT STATUS REGISTER GND T_CRIT T_CRIT INTERRUPT OTP DEVICE ADDRESS REGISTER SMBus INTERFACE 002aad202 SDATA Fig 1. SCLK Block diagram SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 3 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 6. Pinning information 6.1 Pinning VDD 1 8 SCLK D+ 2 7 SDATA D− 3 6 ALERT T_CRIT 4 5 GND VDD 1 8 SCLK D+ 2 7 SDATA D− 3 T_CRIT 4 SA56004XD SA56004XDP ALERT 5 GND 002aad199 002aad198 Fig 2. 6 Pin configuration for SO8 Fig 3. Pin configuration for TSSOP8 terminal 1 index area VDD 1 D+ 2 8 SCLK 7 SDATA SA56004XTK D− 3 6 ALERT T_CRIT 4 5 GND 002aad200 Transparent top view Fig 4. Pin configuration for HVSON8 6.2 Pin description Table 3. Pin description Symbol Pin Description VDD 1 Positive supply voltage. DC voltage from 3.0 V to 5.5 V. D+ 2 Diode current source (anode). D− 3 Diode sink current (cathode). T_CRIT 4 T_CRIT alarm is open-drain, active LOW output which requires an external pull-up resistor. It functions as a system interrupt or power shutdown. GND 5 Power supply ground. ALERT 6 ALERT alarm is an open-drain, active LOW output which requires an external pull-up resistor. It functions as an interrupt indicating that the temperature of the on-chip or remote diode is above or below programmed overtemperature or undertemperature thresholds. SDATA 7 SMBus/I2C-bus bidirectional data line. This is an open-drain output which requires an external pull-up resistor. SCLK 8 SMBus/I2C-bus clock input which requires an external pull-up resistor. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 4 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 7. Functional description Refer to Figure 1 “Block diagram”. 7.1 Serial bus interface The SA56004X should be connected to a compatible two-wire serial interface System Management Bus (SMBus) as a slave device using the two device terminals SCLK and SDATA. The ALERT pin can optionally be used with the SMBus protocol to implement the ARA response. The controller will provide a clock signal to the device SCLK pin and write/read data to/from the device through the device SDATA pin. External pull-up resistors, about 10 kΩ each, are needed for these device pins due to open-drain circuitry. Data of 8-bit digital byte or word are used for communication between the controller and the device using SMBus 2.0 protocols which are described more in Section 7.10 “SMBus interface”. The operation of the device to the bus is described with details in the following sections. 7.2 Slave address The SA56004X has a 7-bit slave address register which is factory programmed in OTP memory. Eight unique devices are available with different slave addresses as defined in Table 2 “Ordering options”. Up to eight devices can reside on the same SMBus without conflict, provided that their addresses are unique. 7.3 Register overview The SA56004X contains three types of SMBus addressable registers. These are read-only (R), write-only (W), and read-write (R/W). Attempting to write to any R-only register or read data from any W-only register will produce an invalid result. Some of the R/W registers have separate addresses for reading and writing operations. The registers of the SA56004X serve four purposes: • • • • Control and configuration of the SA56004X Status reporting Temperature measurement storage ID and manufacturer test registers Table 4 describes the names, addresses, Power-On Reset (POR), and functions of each register. The data of the temperature-related registers is in 2’s complement format in which the MSB is the sign bit. The 8-bit data of other registers is in 8-bit straight format. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 5 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Table 4. Register assignments Register name Command byte POR state Function Bits Access Read address Write address LTHB 00h n/a 0000 0000 local temperature high byte 8 R RTHB 01h n/a 0000 0000 remote temperature high byte 8 R SR 02h n/a 0000 0000 status register 8 R CON 03h 09h 0000 0000 configuration register 8 R/W CR 04h 0Ah 1000 conversion rate 4 R/W LHS 05h 0Bh 0100 0110 local high setpoint 8 R/W LLS 06h 0Ch 0000 0000 local low setpoint 8 R/W RHSHB 07h 0Dh 0100 0110 remote high setpoint high byte 8 R/W RLSHB 08h 0Eh 0000 0000 remote low setpoint high byte 8 R/W One Shot n/a 0Fh - writing register initiates a one shot conversion 0 W RTLB 10h n/a 0000 00 remote temperature low byte 6 (MSBs) R RTOHB 11h 11h 0000 0000 remote temperature offset high byte 8 R/W RTOLB 12h 12h 000 remote temperature offset low byte 3 (MSBs) R/W RHSLB 13h 13h 000 remote high setpoint low byte 3 (MSBs) R/W RLSLB 14h 14h 000 remote low setpoint low byte 3 (MSBs) R/W RCS 19h 19h 0101 0101 remote T_CRIT setpoint 8 R/W LCS 20h 20h 0101 0101 local T_CRIT setpoint 8 R/W TH 21h 21h 0 1010 T_CRIT hysteresis 5 R/W ATLB 22h n/a 0000 0000 local temperature low byte 3 (MSBs) R AM BFh BFh 0 Alert mode 1 R/W RMID FEh n/a 1010 0001 read manufacturer’s ID 8 R RDR FFh n/a 0000 0000 read stepping or die revision 8 R 7.4 Power-on reset When power is applied to the SA56004X, the device will enter into its Power-On Reset (POR) state and its registers are reset to their default values. The configuration, status, and temperature-reading registers remain in these states until after the first conversion. As shown in Table 4 this results in: 1. Command register set to 00h. 2. Local Temperature register (LTHB and LTLB) set to 0 °C. 3. Remote Diode Temperature register (RTHB and RTLB) set to 0 °C until the end of the first conversion. 4. Status register (SR) set to 00h. 5. Configuration register (CON) set to 00h; interrupt latches are cleared, the ALERT and T_CRIT output drivers are off and the ALERT and T_CRIT pins are pulled HIGH by the external pull-up resistors. 6. Local T_CRIT temperature setpoints (LCS) and Remote T_CRIT temperature setpoints (RCS) at 85 °C. 7. Local HIGH setpoint (LHS) and remote HIGH temperature setpoint (RHSHB) at 70 °C. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 6 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 8. Local LOW setpoint (LLS) and Remote LOW temperature setpoints (RLSHB) at 0 °C. 9. Conversion Rate register (CR) is set to 8h; the default value of about 16 conversions/s. 7.5 Starting conversion Upon POR, the RUN/STOP bit 6 of the configuration register is zero (default condition), then, the device will enter into its free-running operation mode in which the device A/D converter is enabled and the measurement function is activated. In this mode, the device cycles the measurements of the local and remote temperature automatically and periodically. The conversion rate is defined by the programmable conversion rate stored in the conversion rate register. It also performs comparison between readings and limits of the temperature in order to set the flags and interruption accordingly at the end of every conversion. Measured values are stored in the temp registers, results of the limit comparisons are reflected by the status of the flag bits in the status register and the interruption is reflected by the logical level of the ALERT and T_CRIT output. If the power-on temperature limit is not suitable, the temp limit values could be written into the limit registers during the busy-conversion duration of about 38 ms of the first conversion after power-up. Otherwise, the status register must be read and the configuration bit 7 must be reset in order to recover the device from interruption caused by the undesired temp limits. 7.6 Low power software standby mode The device can be placed in a software standby mode by setting the RUN/STOP bit 6 in the configuration register HIGH (logic 1). In standby, the free-running oscillator is stopped, the supply current is less than 10 µA if there is no SMBus activity, all data in the registers is retained. However, the SMBus is still active and reading and writing registers can still be performed. A one-shot command will initiate a single conversion which has the same effect as any conversion that occurs when the device is in its free-running mode. To restore the device to free running mode, set the RUN/STOP bit 6 LOW (logic 0). 7.7 Temperature data format The temperature data can only be read from the Local and Remote Temperature registers; the setpoint registers (e.g., T_CRIT, LOW, HIGH) are read/write. Both local and remote temperature reading data is represented by an 11-bit, 2’s complement word with the Least Significant Bit (LSB) = 0.125 °C. The temperature setpoint data for the remote channel is also represented by an 11-bit, 2’s complement word with the LSB = 0.125 °C. The temperature setpoint data for both the local channel and the T_CRIT setpoints are represented by 8-bit, 2’s complement words with the LSB =1.0 °C. For 11-bit temp data, the data format is a left justified, 16-bit word available in two 8-bit registers (high byte and low byte). For 8-bit temp data, the data is available in a single 8-bit register (high byte only). SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 7 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Table 5. Temperature data format Temperature Digital output Binary Hex +125 °C 0111 1101 0000 0000 7D00h +25 °C 0001 1001 0000 0000 1900h +1 °C 0000 0001 0000 0000 0100h +0.125 °C 0000 0000 0010 0000 0020h 0 °C 0000 0000 0000 0000 0000h −0.125 °C 1111 1111 1110 0000 FFE0h −1 °C 1111 1111 0000 0000 FF00h −25 °C 1110 0111 0000 0000 E700h −55 °C 1100 1001 0000 0000 C900h 7.8 SA56004X SMBus registers 7.8.1 Command register The command register selects which register will be read or written to. Data for this register should be transmitted during the Command Byte of the SMBus write communication. 7.8.2 Local and remote temperature registers (LTHB, LTLB, RTHB, RTLB) Table 6. Byte LTHB, LTLB, RTHB, RTLB - Local and remote temperature registers High byte (read only; address 00h, 01h) Low byte (read only; address 10h) Bit D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Value sign 64 32 16 8 4 2 1 0.5 0.25 0.125 0 0 0 0 0 7.8.3 Configuration register (CON) The configuration register is an 8-bit register with read address 03h and write address 09h. Table 7 shows how the bits in this register are used. Table 7. CON - Configuration register (read address 03h; write address 09h) bit assignments Bit Description POR state 7 ALERT mask. 0 The ALERT interrupt is enabled when this bit is LOW. The ALERT interrupt is disabled (masked) when this bit is HIGH. 6 RUN/STOP. 0 Standby or run mode control. Running mode is enabled when this bit is LOW. The SA56004X is in standby mode when this bit is HIGH. 5 4 Not defined; defaults to logic 0. 0 Remote T_CRIT mask. 0 The T_CRIT output will be activated by a remote temperature that exceeds the remote T_CRIT setpoint when this bit is LOW. The T_CRIT output will not be activated under this condition when this bit is HIGH. 3 Not defined; defaults to logic 0. SA56004X_5 Product data sheet 0 © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 8 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Table 7. CON - Configuration register (read address 03h; write address 09h) bit assignments …continued Bit Description POR state 2 Local T_CRIT mask. 0 The T_CRIT output will be activated by a local temperature that exceeds the local T_CRIT setpoint when this bit is LOW. The T_CRIT output will not be activated under this condition when this bit is HIGH. 1 0 Not defined; defaults to logic 0. 0 Fault queue. 0 A single remote temperature measurement outside the HIGH, LOW or T_CRIT setpoints will trigger an outside limit condition resulting in setting the status bits and associated output pins when this bit is LOW. Three consecutive measurements outside of one of these setpoints are required to trigger an outside of limit condition when this bit is HIGH. 7.8.4 Status register (SR) The contents of the status register reflect condition status resulting from all activities: comparison between temperature measurements and temperature limits, the status of A/D conversion, and the hardware condition of external diode to the device. Bit assignments are listed in Table 8. This register is read-only and its address is 02h. Upon POR, all bits are set to zero. Remark: Any one of the fault conditions, with the exceptions of Diode OPEN and A/D BUSY, introduces an Alert interrupt (see Section 7.9.1.2). Also, whenever a one-shot command is executed, the status byte should be read after the conversion is completed, which is about 38 ms (1 conversion time period) after the one-shot command is sent. Table 8. SR - Status register (read-only address 02h) bit assignments Bit Name Description 7 BUSY When logic 1, A/D is busy converting. POR state = n/a. 6 LHIGH When logic 1, indicates local HIGH temperature alarm. POR state = 0. 5 LLOW When logic 1, indicates a local LOW temperature alarm. POR state = 0. 4 RHIGH When logic 1, indicates a remote diode HIGH temperature alarm. POR state = 0. 3 RLOW When logic 1, indicates a remote diode LOW temperature alarm. POR state = 0. 2 OPEN When logic 1, indicates a remote diode disconnect. POR state = 0. 1 RCRIT When logic 1, indicates a remote diode critical temperature alarm. POR state = 0. 0 LCRIT When logic 1, indicates a local critical temperature alarm. POR state = 0. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 9 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 7.8.5 Conversion rate register (CR) The conversion rate register is used to store programmable conversion data, which defines the time interval between conversions in the standard free-running auto convert mode. Table 9 shows all applicable data values and rates for the SA56004X. Only the 4 LSBs of the register are used and the other bits are reserved for future use. The register is R/W using the read address 04h and write address 0Ah. The POR default conversion data is 08h. Table 9. Conversion rate control byte (CR) Data value Conversion rate (Hz) 00h 0.06 01h 0.12 02h 0.25 03h 0.50 04h 1.0 05h 2 06h 4 07h 8 08h 16 09h 32 0Ah to FFh n/a 7.8.6 Temperature limit registers Table 10. Byte LHS, RHSHB, RHSLB - Local and remote HIGH setpoint registers Low byte (read/write address 13h)[2] High byte (read only address 05h, 07h; write address 0Bh, 0Dh)[1] Bit D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Value sign 64 32 16 8 4 2 1 0.5 0.25 0.125 0 0 0 0 0 [1] POR default LHS = RHSHV = 46h (70 °C). [2] POR default RHSLB = 00h. Table 11. Byte LLS, RLSHB, RLSLB - Local and remote LOW setpoint registers Low byte (read/write address 14h)[2] High byte (read address 06h, 08h; write address 0Ch, 0Eh)[1] Bit D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Value sign 64 32 16 8 4 2 1 0.5 0.25 0.125 0 0 0 0 0 [1] POR default LLS = RLSHV = 00h. [2] POR default RLSLB = 00h (0 °C). Table 12. Byte LCS, RCS - Local and remote T_CRIT registers Single high byte (read/write address 20h, 19h)[1] Bit D7 D6 D5 D4 D3 D2 D1 D0 Value sign 64 32 16 8 4 2 1 [1] POR default LCS = RCS = 55h (85 °C). SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 10 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Table 13. TH - T_CRIT hysteresis register Single high byte (read/write address 21h)[1] Byte Bit Value [1] D7 D6 D5 D4 D3 D2 D1 D0 - - - 16 8 4 2 1 POR default TH = 0Ah (10 °C). 7.8.7 Programmable offset register (remote only) Table 14. Byte RTOHB, RTOLB - Remote temperature offset registers High byte (read/write address 11h)[1] Low byte (read/write address 12h)[2] Bit D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Value sign 64 32 16 8 4 2 1 0.5 0.25 0.125 0 0 0 0 0 [1] POR default RTOHB = RTOLB = 00h. [2] POR default RTOLB = 00h. 7.8.8 ALERT mode register (AM) Table 15. AM - ALERT mode register Read and write address BFh. Bit Value D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 ALERT mode D[7:1] is not defined and defaults to logic 0. D0: The ALERT output is in interrupt mode when this bit is LOW. The ALERT output is in comparator mode when this bit is HIGH. 7.8.9 Other registers The Manufacturers ID register has a default value A1h (1010 0001) and a read address FEh. The Die Revision Code register has a default value 00h (0000 0000) and read address FFh. This register will increment by 1 every time there is a revision to the die. 7.8.10 One-shot register The one-shot register is used to initiate a single conversion and comparison cycle when the device is in the standby mode; upon completion of the single conversion cycle, the device returns to the standby mode. It is not a data register; it is the write operation that causes the one-shot conversion. The data written to this register is not stored; an FFh value will always be read from this register. To initiate a one-shot operation, send a standard write command with the command byte of 0Fh (One-Shot Write Address). SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 11 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 7.9 Interruption logic and functional description 7.9.1 ALERT output The ALERT output is used to signal Alert interruptions from the device to the SMBus or other system interrupt handler and it is active LOW. Because this is an open-drain output, a pull-up resistor (typically 10 kΩ) to VDD is required. Several slave devices can share a common interrupt line on the same SMBus. The ALERT function is very versatile and accommodates three separate operating modes: • Temperature comparator • System interrupt based on temperature • SMBus Alert Response Address (ARA) response. The ARA and interrupt modes are different only in how the user interacts with the SA56004X. At the end of every temperature reading, digital comparators determine if the readings are above the HIGH or T_CRIT setpoint or below the LOW setpoint register values. If so, the corresponding bit in the Status register is set. If the ALERT mask bit 7 of the Configuration register is not HIGH, then any bit set in the Status register other than the BUSY (D7) and OPEN (D2) will cause the ALERT output pin to be active LOW. An alert will be triggered after any conversion cycle that finds the temperature is out of the limits defined by the setpoint registers. In order to trigger an ALERT in all alert modes, the ALERT mask bit 7 of the Configuration register must be cleared (not HIGH). 7.9.1.1 ALERT output in comparator mode When operating the SA56004X in a system that utilizes an SMBus controller not having an interrupt, the ALERT output may be operated as a temperature comparator. In this mode, when the condition that triggered the ALERT to be asserted is no longer present, the ALERT output is released as it goes HIGH. In order to use the ALERT output as a temperature comparator, bit D0 (the ALERT configure bit) in the ALERT Mode (AM) register must be set HIGH. This is not the POR default. 7.9.1.2 ALERT output in interrupt mode In the interrupt mode, the ALERT output is used to provide an interrupt signal that remains asserted until the interrupt service routine has elapsed. In the interrupt operating mode, a read of the Status register will set the ALERT mask bit 7 of the Configuration register if any of the temperature alarm bits of the Status register is set, with exception of BUSY (D7) and OPEN (D2). This protocol prevents further ALERT output triggering until the master device has reset the ALERT mask bit at the end of the interrupt service routine. The Status register bits are cleared only upon a read of the Status register by the serial bus master (see Figure 5). In order for the ALERT output to be used as an interrupt, the ALERT Configure bit D0 of the ALERT Mode (AM) register must be set LOW (POR default). SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 12 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms remote temperature high limit remote diode temperature ALERT pin status register bit 4 (RHIGH) A B, C D E, F 002aad216 Fig 5. ALERT output in interrupt mode The following events summarize the ALERT output interrupt mode of operation: Event A: Master senses ALERT output being active-LOW. Event B: Master reads the SA56004X Status register to determine what cause the ALERT interrupt. Event C: SA56004X clears the Status register, resets the ALERT output HIGH, and sets the ALERT mask bit 7 in the Configuration register. Event D: A new conversion result indicates the temperature is still above the high limit, however the ALERT pin is not activated due to the ALERT mask. Event E: Master should correct the conditions that caused the ALERT output to be triggered. For instance, the fan is started, setpoint levels are adjusted. Event F: Master resets the ALERT mask bit 7 in the Configuration register. 7.9.1.3 ALERT output in SMBus ALERT mode When several slave devices share a common interrupt line, an SMBus alert line is implemented. The SA56004X is designed to accommodate the Alert interrupt detection capability of the SMBus 2.0 Alert Response Address (ARA) protocol, defined in SMBus specification 2.0. This procedure is designed to assist the master in resolving which slave device generated the interrupt and in servicing the interrupt while minimizing the time to restore the system to its proper operation. Basically, the SMBus provides Alert response interrupt pointers in order to identify slave devices which have caused the Alert interrupt. When the ARA command is received by all devices on the SMBus, the devices pulling the SMBus alert line LOW send their device addresses to the master; await an acknowledgement and then release the alert line. This requirement to disengage the SMBus alert line prevents locking up the alert line. The SA56004X complies with this ARA disengagement protocol by setting the ALERT mask bit 7 in the Configuration register at address 09h after successfully sending out its address in response to an ARA command and releasing the ALERT output. Once the mask bit is activated, the ALERT output will be disabled until enabled by software. In order to enable the ALERT the master must read the SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 13 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Status register, at address 02h, during the interrupt service routine and then reset the ALERT mask bit 7 in the Configuration register to logic 0 at the end of the interrupt service routine (see Figure 6). In order for the SA56004X to respond to the ARA command, the bit D0 in the ALERT mode register must be set LOW. ALERT mask bit 7 and the ALERT mode bit D0 are both LOW for the POR default. remote temperature high limit remote diode temperature temperature ALERT pin status register bit 4 (RHIGH) A Fig 6. B C D 002aad215 ALERT pin in SMBus Alert mode The following events summarize the ALERT output interrupt operation in the SMBus Alert mode: Event A: Master senses the ALERT line being LOW. Event A to B: Master sends a read command using the common 7-bit Alert Response Address (ARA) of 0001100. Event A to B: Alerting device(s) return ACK signal and their addresses using the I2C-bus Arbitration (the device with the lowest address value sends its address first. The master can repeat the alert reading process and work up through all the interrupts). Event B: Upon the successful completion of returning address, the SA56004X resets its ALERT output (to OFF) and sets the ALERT mask bit 7 in its configuration register. Event C: Master should read the device status register to identify and correct the conditions that caused the Alert interruption. The status register is reset. Event D: Master resets the ALERT mask bit 7 in the configuration register to enable the device ALERT output interruption. Remark: The bit assignment of the returned data from the ARA reading is listed in Table 16. If none of the devices on the bus is alerted then the returned data from ARA reading will be FFh (1111 1111). SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 14 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Table 16. ALERT response bit assignment ALERT response bit Device address bit Function 7 (MSB) ADD6 address bit 6 (MSB) of alerted device 6 ADD5 address bit 5 of alerted device 5 ADD4 address bit 4 of alerted device 4 ADD3 address bit 3 of alerted device 3 ADD2 address bit 2 of alerted device 2 ADD1 address bit 1 of alerted device 1 ADD0 address bit 0 of alerted device 0 1 always logic 1 7.9.2 T_CRIT output The T_CRIT output is LOW when any temperature reading is greater than the preset limit in the corresponding critical temperature setpoint register. When one of the T_CRIT setpoint temperatures is exceeded, the appropriate status register bit, 1 (RCRIT) or 0 (LCRIT), is set. After every local and remote temperature conversion the status register flags and the T_CRIT output are updated. Figure 7 is a timing diagram showing the relationship of T_CRIT output, Status bit 1 (RCRIT) and the remote critical temperature setpoint (RCS), and critical temperature hysteresis (TH) with remote temperature changes. Note that the T_CRIT output is de-activated only after the remote temperature is below the remote temperature setpoint, RCS minus the hysteresis, TH. In the interrupt mode only, the Status register flags are reset after the Status register is read. RCS remote temperature RCS − TH Status register bit 1 (RCRIT) T_CRIT output A Fig 7. B C 002aad217 T_CRIT temperature response timing Event A: T_CRIT goes LOW and Status bit 1 (RCRIT) is set HIGH when Remote Temperature exceeds RCS, Remote T_CRIT Setpoint. Event B: Remote Temperature goes below RCS − TH. T_CRIT is de-activated, but Status register remains unchanged. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 15 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Event C: The Status register bit 1 (RCRIT) is reset by a read of the Status register (in the interrupt mode). 7.9.3 Fault Queue To suppress erroneous ALERT or T_CRIT triggering, the SA56004X implements a Fault Queue for both local and remote channel. The Fault Queue insures a temperature measurement is genuinely beyond a HIGH, LOW or T_CRIT setpoint by not triggering until three consecutive out-of-limit measurements have been made. The fault queue defaults OFF upon POR and may be activated by setting bit 0 in the Configuration register (address 09h) to logic 1. remote temperature RCS RCS − TH remote HIGH setpoint remote LOW setpoint ALERT output T_CRIT output events A B C D E F G H I 002aad218 Remark: All events indicate the completion of a conversion. Fig 8. Fault queue remote HIGH and LOW and T_CRIT, T_CRIT hysteresis setpoint response (comparator mode) Event A: The remote temperature has exceeded the Remote HIGH setpoint. Event B: Three consecutive over limit measurements have been made exceeding the Remote HIGH setpoint; the ALERT output is activated (goes LOW). By now, the remote temp has exceeded the Remote T_CRIT setpoint (RCS). Event C: Three consecutive over limit measurements have been made exceeding RCS; the T_CRIT output is activated (goes LOW). Event D: The remote temperature falls below the RCS − TH setpoint. Event E: The ALERT output is de-activated (goes HIGH) after a below_high_limit temperature measurement is completed. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 16 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Event F: Three consecutive measurements have been made with the remote temperature below the RCS − TH threshold; the T_CRIT output is de-activated (goes HIGH). Event G: The remote temp falls below the Remote LOW setpoint. Event H: Three consecutive measurements are made with the temp below the Remote LOW setpoint; ALERT output is activated (goes LOW). Event I: The ALERT output is de-activated (goes HIGH) after a above_low_limit temperature measurement is completed. 7.9.4 Remote diode selection To measure the remote temperature or the temperature of an externally attached diode, the device automatically forces two successive currents of about 160 µA and 10 µA at D+ pin. It measures the voltage (VBE) between D+ and D−, detects the difference between the two VBE voltages or the ∆VBE and then converts the ∆VBE into a temperature data using the basic PTAT voltage formula as shown in Equation 1. The device typically takes about 38 ms to perform a measurement during each conversion period or cycle, which is selectable by programming the conversion rate register. l2 kT ∆V BE = n × ------ × ln ----- l1 q (1) Where: n = diode ideality factor k = Boltzmann’s constant T = absolute temperature (°K) = 273 °C + T (°C) q = electron charge ln = natural logarithm l2, l1 = two source currents Because the device does not directly convert the sensed VBE as in the old method of temperature measurement systems, the VBE calibration is not required. Furthermore, the device remote temperature error is adjusted at the manufacturer to meet the specifications with the use of the reference diode-connected transistors such as the 2N3904/2N3906. The diode type to be used in customer applications must have the characteristics as close to the 2N3904/2N3906 as possible in order to obtain optimal results. Finally, to prevent the effects of system noise on the measured VBE signals, an external capacitor of about 2200 pF connected between the D+ and D− pins as well as the grounded-shield cable for the diode connection wires are recommended. 7.9.5 Diode fault detection The SA56004X is designed with circuitry to detect the fault conditions of the remote diode. When the D+ pin is shorted to VDD or floating, the Remote Temperature High Byte (RTHB) register is loaded with +127 °C, the Remote Temperature Low Byte (RTLB) register is loaded with 0 °C, and the OPEN bit (bit 2 of the Status register) is set. Under the above conditions of D+ shorted to VDD or floating, if the Remote T_CRIT setpoint is set less than +127 °C, and T_CRIT Mask are disabled, then, the T_CRIT output pins will be pulled SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 17 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms LOW. Furthermore, if the Remote HIGH Setpoint High Byte (RHSHB) register is set to a value less than +127 °C and the Alert Mask is disabled, then the ALERT output will be pulled LOW. Note that the OPEN bit itself will not trigger an ALERT. When the D+ pin is shorted to ground or to D−, the Remote Temperature High Byte (RTHB) register is loaded with −128 °C (1000 0000) and the OPEN (bit 2 in the Status register) will not be set. Since operating the SA56004X is beyond its normal limits, this temperature reading represents this shorted fault condition. If the value in the Remote Low Setpoint High Byte (RLSHB) register is more than −128 °C and the Alert Mask is disabled, the ALERT output will be pulled LOW. 7.10 SMBus interface The device can communicate over a standard two-wire serial interface System Management Bus (SMBus) or compatible I2C-bus using SCLK and SDATA. The device employs four standard SMBus protocols: Write Byte, Read Byte, Receive Byte, and Send Byte. Data formats of four protocols are shown in Figure 9. The following key points of protocol are important: • The SMBus master initiates data transfer by establishing a START condition (S) and terminates data transfer by generating a STOP condition (P). • Data is sent over the serial bus in sequences of 9 clock pulses according to each 8-bit data byte followed by 1-bit status of device acknowledgement (A). • The 7-bit slave address is equivalent to factory-programmed address of the device. • The command byte is equivalent to the address of the selected device register. • The Receive Byte format is used for quicker transfer data from a device reading register that was previously selected. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 18 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 (cont.) SCLK a6 SDATA a5 a4 a3 a2 a1 a0 D7 S W START D6 D5 D4 D3 D2 D1 (cont.) D0 A A device address device register command 1 2 3 4 5 6 7 8 D7 D6 D5 D4 D3 D2 D1 D0 9 SCLK SDATA A P data to be written to register STOP 002aad219 a. Write Byte format (to write a data byte to the device register) 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 (cont.) SCLK a6 SDATA a5 a4 a3 a2 a1 a0 D7 S W START D6 D5 D4 D3 D2 D1 (cont.) D0 A A device address P STOP device register command 1 2 3 4 5 6 7 8 a6 a5 a4 a3 a2 a1 a0 9 1 2 3 4 5 6 7 8 9 D7 D6 D5 D4 D3 D2 D1 D0 SCLK SDATA S R RESTART A NA device address P STOP data from device register 002aad220 b. Read Byte format (to read a data byte from the device register) SCLK (cont.) (cont.) SDATA 1 2 3 4 5 6 7 a6 a5 a4 a3 a2 a1 a0 S 8 9 R RESTART 1 2 3 4 5 6 7 8 9 D7 D6 D5 D4 D3 D2 D1 D0 A NA P device address STOP data from device register 002aad221 c. Receive Byte format (to read a data byte from already pointed register) 1 2 3 4 5 6 7 a6 a5 a4 a3 a2 a1 a0 8 9 W A 1 2 3 4 5 6 7 8 D7 D6 D5 D4 D3 D2 D1 D0 9 SCLK SDATA S START device address A device register command P STOP 002aad222 d. Send Byte format Fig 9. SMBus interface protocols SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 19 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 7.10.1 Serial interface reset If the SMBus master attempts to reset the SA56004X while the SA56004X is controlling the data line and transmitting on the data line, the SA56004X must be returned to a known state in the communication protocol. This may be accomplished in two ways: 1. When the SDATA is LOW, the SA56004X SMBus state machine resets to the SMBus idle state if SCLK is held LOW for more than 35 ms (maximum TIMEOUT period). According to SMBus specification 2.0, all devices are required to time-out when the SCLK line is held LOW for 25 ms to 35 ms. Therefore, to insure a time-out of all devices on the bus, the SCLK line must be held LOW for at least 35 ms. 2. When the SDATA is HIGH, the master initiates an SMBus START. The SA56004X will respond properly to a SMBus START condition only during the data retrieving cycle. After the START, the SA56004X will expect an SMBus Address byte. 8. Simplified system diagram VDD R 10 kΩ 1 VDD SCLK 8 R 10 kΩ R 10 kΩ CLOCK 100 nF SA56004X shielded twisted pair 2 D+ SDATA D− ALERT VDD SMBus CONTROLLER 7 DATA 2.2 nF(1) 3 remote sensor 2N3904 (NPN), 2N3906 (PNP), or similar standalone, ASIC or microprocessor thermal diode +5 V 6 INT VDD R 10 kΩ 4 T_CRIT GND 5 FAN CONTROL CIRCUIT 002aad201 (1) Typical value; placed close to temperature sensor. Fig 10. Simplified system diagram SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 20 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 9. Limiting values Table 17. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are referenced to GND. Symbol Parameter VDD Min Max Unit supply voltage −0.3 +6 V voltage at SDATA, SCLK, ALERT, T_CRIT −0.3 +6 V VD+ voltage at positive diode input −0.3 VDD + 0.3 V VD− voltage at negative diode input −0.3 +0.8 V Isink sink current −1 +50 mA ID+ D+ input current −1 +1 mA Human Body Model [1] - 2000 V Machine Model [1] - 200 V Vesd electrostatic discharge voltage Conditions SDATA, SCLK, ALERT, T_CRIT Tj(max) maximum junction temperature - +150 °C Tstg storage temperature −65 +165 °C [1] The D+ and D− pins are 1000 V HBM and 100 V MM due to the higher sensitivity of the analog pins that introduces a limitation to the circuit protection structure. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 21 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 10. Characteristics Table 18. Electrical characteristics VDD = 3.0 V to 3.6 V; Tamb = −40 °C to +125 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit TERRL local temperature error Tamb = +60 °C to +100 °C −2 ±1 +2 °C Tamb = −40 °C to +125 °C −3 - +3 °C TERRR remote temperature error Tamb = +25 °C to +85 °C; TRD = +60 °C to +100 °C −1 - +1 °C Tamb = −40 °C to +85 °C; TRD = −40 °C to +125 °C −3 - +3 °C remote temperature resolution - 11 - bit - 0.125 - °C TRESL local temperature resolution - 11 - bit - 0.125 - °C Tconv conversion period - 38 - ms VDD supply voltage 3.0 - 5.5 V IDD quiescent current during conversion, 16 Hz conversion rate - 500 - µA shut-down current SMBus inactive - 10 - µA remote diode source current high setting: D+ − D− = +0.65 V - 160 - µA TRESR IRD [1] - 10 - µA 2.6 - 2.95 V 1.8 - 2.4 V local and remote ALERT high default values set at power-up default temperature settings - +70 - °C local and remote ALERT low default temperature settings default values set at power-up - 0 - °C local and remote T_CRIT default temperature settings default values set at power-up - +85 - °C T_CRIT hysteresis default value set at power-up - +10 - °C ALERT and T_CRIT output saturation voltage IO = 6.0 mA - - 0.4 V low setting UVL UnderVoltage Lockout (UVL) threshold voltage[2] VDD input disables A/D conversion [3] Power-On Reset (POR) threshold voltage VDD input falling edge [4] [1] The SA56004X is optimized for 3.3 V VDD operation. [2] Definition of Under Voltage Lockout (UVL): The value of VDD below which the internal A/D converter is disabled. This is designed to be a minimum of 200 mV above the power-on reset. During the time that it is disabled, the temperature that is in the ‘read temperature registers’ will remain at the value that it was before the A/D was disabled. This is done to eliminate the possibility of reading unexpected false temperatures due to the A/D converter not working correctly due to low voltage. In case of power-up (rising VDD), the reading that is stored in the ‘read temperature registers’ will be the default value of 0 °C. VDD will rise to the value of the UVL, at which point the A/D will function correctly and the normal temperature will be read. [3] VDD (rising edge) voltage below which the A/D converter is disabled. [4] VDD (falling edge) voltage below which the logic is reset. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 22 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Table 19. SMBus interface characteristics VDD = 3.0 V to 3.6 V; Tamb = −40 °C to +125 °C; unless otherwise specified. These specifications are guaranteed by design and not tested in production. Symbol Parameter Conditions Min Typ Max Unit VIH HIGH-level input voltage SCLK, SDATA; VDD = 2.7 V to 5.5 V 2.2 - - V VIL LOW-level input voltage SCLK, SDATA; VDD = 2.7 V to 5.5 V - - 0.8 V IOL LOW-level output current ALERT, T_CRIT; VOL = 0.4 V 1.0 - - mA 6.0 - - mA IOH LOW-level output current - - 1.0 µA IIL LOW-level input current −1.0 - - µA IIH HIGH-level input current - - 1.0 µA Ci input capacitance - 5 - pF - - 400 kHz 600 5000 - ns SDATA; VOL = 0.6 V SCLK, SDATA SMBus digital switching characteristics[1] fSCLK SCLK operating frequency tLOW SCLK LOW time 10 % to 10 % tHIGH SCLK HIGH time 90 % to 90 % tBUF SMBus free time[2] tHD;STA hold time of START condition[3] tHD;DAT data[4] hold time of 10 % of SDATA to 90 % of SCLK in[5] 600 5000 - ns 600 - - ns 600 - - ns 0 300 - ns 250 - - ns 250 - - ns ns tSU;DAT set-up time of data tSU;STA set-up time of repeat START condition[6] tSU;STO set-up time of STOP condition[7] 90 % of SCLK to 90 % of SDATA 250 - - tr rise time SCLK and SDATA - - 1 µs tf fall time SCLK and SDATA - - 300 ns tof output fall time CL = 400 pF; IO = 3 mA - - 250 ns 25 - 35 ms tto(SMBus) SMBus time-out 90 % to 90 % time[8] [1] The switching characteristics of the SA56004X fully meet or exceed all parameters specified in SMBus version 2.0. The following parameters specify the timing between the SCLK and SDATA signals in the SA56004X. They adhere to, but are not necessarily specified as the SMBus specifications. [2] Delay from SDATA STOP to SDATA START. [3] Delay from SDATA START to first SCLK HIGH-to-LOW transition. [4] Delay from SCLK HIGH-to-LOW transition to SDATA edges. [5] Delay from SDATA edges to SCLK LOW-to-HIGH transition. [6] Delay from SCLK LOW-to-HIGH transition to restart SDATA. [7] Delay from SCLK HIGH-to-LOW transition to SDATA STOP condition. [8] LOW period for reset of SMBus. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 23 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms tr tf tHD;STA tLOW SCLK tHD;DAT tHD;STA tHIGH tSU;STA tSU;STO tSU;DAT SDATA tBUF P S S P 002aad237 Fig 11. Timing measurements SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 24 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 11. Performance curves 24 IDD shutdown (µA) 002aad228 16 600 8 400 0 −50 −25 0 25 50 75 125 100 Tamb (°C) Fig 12. Typical IDD shutdown versus temperature and VDD 400 IDD quiescent (µA) 002aad229 800 IDD quiescent (µA) VDD = 5.5 V 3.6 V 3.3 V 3.0 V 002aad230 VDD = 5.5 V 3.6 V 3.3 V 3.0 V 200 −50 −25 0 25 75 002aad231 (1) 400 300 (2) 300 (3) (4) 200 200 (8) (9) (5) (6) (7) 100 −50 125 100 Tamb (°C) Fig 13. Typical IDD quiescent current versus temperature and VDD (conversion rate = 16 Hz) 500 IDD quiescent (µA) VDD = 5.5 V 3.6 V 3.3 V 3.0 V 50 −25 0 25 50 75 125 100 Tamb (°C) 100 −50 −25 0 25 50 75 125 100 Tamb (°C) Conversion rate: (1) 16 Hz (2) 8.0 Hz (3) 4.0 Hz (4) 2.0 Hz (5) 1.0 Hz (6) 0.5 Hz (7) 0.25 Hz (8) 0.12 Hz (9) 0.06 Hz Fig 14. Typical IDD quiescent current versus temperature and VDD (conversion rate = 0.06 Hz) Fig 15. Typical IDD quiescent current versus temperature and conversion rate (VDD = 3.3 V) SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 25 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 002aad232 14 IOL (mA) VDD = 5.5 V 3.6 V 3.3 V 3.0 V IOL (mA) 10 8 6 6 2 −50 −25 0 25 50 75 4 −50 125 100 Tamb (°C) Fig 16. Typical T_CRIT IOL versus temperature and VDD (VOL = 0.4 V) 002aad233 2.80 002aad234 10 VDD = 5.5 V 3.6 V 3.3 V 3.0 V −25 0 25 50 75 125 100 Tamb (°C) Fig 17. Typical ALERT IOL versus temperature and VDD (VOL = 0.4 V) 002aad235 2.6 VPOR (V) UVL (V) 2.78 2.2 2.76 1.8 2.74 2.72 VDD = 5.5 V 3.6 V 3.3 V 3.0 V 2.70 −50 −25 1.4 0 25 50 75 125 100 Tamb (°C) Fig 18. Typical UVL versus temperature and VDD 1.0 −50 0 25 50 75 125 100 Tamb (°C) Fig 19. Typical VPOR versus temperature SA56004X_5 Product data sheet −25 © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 26 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 12. Package outline SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE v M A Z 5 8 Q A2 A (A 3) A1 pin 1 index θ Lp 1 L 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 5.0 4.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 inches 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.014 0.0075 0.20 0.19 0.16 0.15 0.05 0.01 0.01 0.004 0.028 0.012 0.244 0.039 0.028 0.041 0.228 0.016 0.024 θ 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT96-1 076E03 MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 20. Package outline SOT96-1 (SO8) SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 27 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm D E SOT505-1 A X c y HE v M A Z 5 8 A2 pin 1 index (A3) A1 A θ Lp L 1 4 detail X e w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(2) e HE L Lp v w y Z(1) θ mm 1.1 0.15 0.05 0.95 0.80 0.25 0.45 0.25 0.28 0.15 3.1 2.9 3.1 2.9 0.65 5.1 4.7 0.94 0.7 0.4 0.1 0.1 0.1 0.70 0.35 6° 0° Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-04-09 03-02-18 SOT505-1 Fig 21. Package outline SOT505-1 (TSSOP8) SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 28 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms HVSON8: plastic thermal enhanced very thin small outline package; no leads; 8 terminals; body 3 x 3 x 0.85 mm SOT782-1 0 1 2 mm scale X A B D A A1 E terminal 1 index area c detail X C e1 terminal 1 index area v M C A B w M C b e 1 y1 C 4 y L Eh 8 5 Dh DIMENSIONS (mm are the original dimensions) UNIT A (1) max. A1 b c D (1) Dh E (1) Eh e e1 L v w y y1 mm 1 0.05 0.00 0.35 0.25 0.2 3.1 2.9 2.55 2.25 3.1 2.9 1.75 1.45 0.65 1.95 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT782-1 --- MO-229 --- EUROPEAN PROJECTION ISSUE DATE 03-01-29 Fig 22. Package outline SOT782-1 (HVSON8) SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 29 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 13. Packing information The SA56004X is packed in reels, as shown in Figure 23. tape guard band reel assembly tape detail cover tape carrier tape barcode label box 002aad226 Fig 23. Tape and reel packing method 14. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 14.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 14.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 30 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 14.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities 14.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 24) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 20 and 21 Table 20. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 ≥ 350 < 2.5 235 220 ≥ 2.5 220 220 SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 31 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms Table 21. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (°C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 24. temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 24. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 15. Mounting 15.1 Printed-circuit board layout considerations Care must be taken in Printed-Circuit Board (PCB) layout to minimize noise induced at the remote temperature sensor inputs, especially in extremely noisy environments, such as a computer motherboard. Noise induced in the traces running between the device sensor inputs and the remote diode can cause temperature conversion errors. Typical sensor signal levels to the SA56004X is a few microvolts. The following guidelines are recommended: 1. Place the SA56004X as close as possible to the remote sensor. It can be from 4 inches to 8 inches, as long as the worst noise sources such as clock generator, data and address buses, CRTs are avoided. SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 32 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 2. Route the D+ and D− lines parallel and close together with ground guards enclosing them (see Figure 25). 3. Leakage currents due to printed-circuit board contamination must be considered. Error can be introduced by these leakage currents. 4. Use wide traces to reduce inductance and noise pick-up. Narrow traces more readily pick up noise. The minimum width of 10 mil and space of 10 mil are recommended. 5. Place a bypass capacitor of 10 nF close to the VDD pin and an input filter capacitor of 2200 pF close to the D+ and D− pins. 6. A shielded twisted pair is recommended if remote sensor is located several feet away from the temperature sensor. Under this circumstance, connect the shield of the cable at the device side to the SA56004X GND pin and leave the shield at the remote end unconnected to avoid ground loop currents. Also notice that the series resistance of the cable may introduce measurement error; 1 Ω can introduce about 0.5 °C. GND D+ D− GND 002aad227 Fig 25. D+ and D− trace layout 16. Abbreviations Table 22. Abbreviations Acronym Description A/D Analog-to-Digital ARA Alert Response Address ASIC Application Specific Integrated Circuit CRT Cathode Ray Tube ESD ElectroStatic Discharge HBM Human Body Model HVAC Heating, Ventilating and Air Conditioning I2C-bus Inter-Integrated Circuit bus LSB Least Significant Bit MM Machine Model MSB Most Significant Bit OTP One-Time Programmable POR Power-On Reset PTAT Proportional To Absolute Temperature SMBus System Management Bus UVL Under Voltage Lockout SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 33 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 17. Revision history Table 23. Revision history Document ID Release date Data sheet status Change notice Supersedes SA56004X_5 20080522 Product data sheet - SA56004X_4 Modifications: • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • • • • Legal texts have been adapted to the new company name where appropriate. Added HVSON8 package option Table 17 “Limiting values”: removed “P, power dissipation” specification from this table Table 19 “SMBus interface characteristics”: – descriptions of parameters moved to table notes – tLOW: Min changed from “4.7 µs” to “600 ns”; Typ changed from “5.0 µs” to “5000 ns” – tHIGH: Min changed from “4.0 µs” to “600 ns”; Typ changed from “5.0 µs” to “5000 ns” – tBUF: Min changed from “4.7 µs” to “600 ns” – tHD;STA: Min changed from “4.0 µs” to “600 ns” – tHD;DAT: Min changed from “-” to “0 ns” – tSU;STO: Min changed from “4.0 µs” to “250 ns” – symbol “tTIMEOUT, SMBus TIMEOUT” changed to “tto(SMBus), SMBus time-out time” SA56004X_4 20060808 Product data sheet - SA56004X_3 SA56004X_3 (9397 750 13841) 20041006 Product data sheet - SA56004X_2 SA56004X_2 (9397 750 12015) 20030903 Objective data - SA56004-X_1 SA56004-X_1 (9397 750 10993) 20030819 Objective data - - SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 34 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 18.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] SA56004X_5 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 05 — 22 May 2008 35 of 36 SA56004X NXP Semiconductors Digital temperature sensor with overtemperature alarms 20. Contents 1 2 3 4 4.1 5 6 6.1 6.2 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.8.1 7.8.2 7.8.3 7.8.4 7.8.5 7.8.6 7.8.7 7.8.8 7.8.9 7.8.10 7.9 7.9.1 7.9.1.1 7.9.1.2 7.9.1.3 7.9.2 7.9.3 7.9.4 7.9.5 7.10 7.10.1 8 9 10 11 12 13 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Serial bus interface . . . . . . . . . . . . . . . . . . . . . . 5 Slave address . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Register overview . . . . . . . . . . . . . . . . . . . . . . . 5 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 6 Starting conversion . . . . . . . . . . . . . . . . . . . . . . 7 Low power software standby mode . . . . . . . . . 7 Temperature data format . . . . . . . . . . . . . . . . . 7 SA56004X SMBus registers . . . . . . . . . . . . . . . 8 Command register . . . . . . . . . . . . . . . . . . . . . . 8 Local and remote temperature registers (LTHB, LTLB, RTHB, RTLB) . . . . . . . . . . . . . . . 8 Configuration register (CON) . . . . . . . . . . . . . . 8 Status register (SR) . . . . . . . . . . . . . . . . . . . . . 9 Conversion rate register (CR) . . . . . . . . . . . . . 10 Temperature limit registers . . . . . . . . . . . . . . . 10 Programmable offset register (remote only) . . 11 ALERT mode register (AM) . . . . . . . . . . . . . . 11 Other registers . . . . . . . . . . . . . . . . . . . . . . . . 11 One-shot register . . . . . . . . . . . . . . . . . . . . . . 11 Interruption logic and functional description . . 12 ALERT output . . . . . . . . . . . . . . . . . . . . . . . . . 12 ALERT output in comparator mode . . . . . . . . 12 ALERT output in interrupt mode . . . . . . . . . . . 12 ALERT output in SMBus ALERT mode . . . . . 13 T_CRIT output . . . . . . . . . . . . . . . . . . . . . . . . 15 Fault Queue . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Remote diode selection . . . . . . . . . . . . . . . . . 17 Diode fault detection . . . . . . . . . . . . . . . . . . . . 17 SMBus interface . . . . . . . . . . . . . . . . . . . . . . . 18 Serial interface reset. . . . . . . . . . . . . . . . . . . . 20 Simplified system diagram . . . . . . . . . . . . . . . 20 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 21 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 22 Performance curves . . . . . . . . . . . . . . . . . . . . 25 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 27 Packing information. . . . . . . . . . . . . . . . . . . . . 30 14 14.1 14.2 14.3 14.4 15 15.1 16 17 18 18.1 18.2 18.3 18.4 19 20 Soldering of SMD packages . . . . . . . . . . . . . . Introduction to soldering. . . . . . . . . . . . . . . . . Wave and reflow soldering . . . . . . . . . . . . . . . Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-circuit board layout considerations . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 30 30 31 31 32 32 33 34 35 35 35 35 35 35 36 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 22 May 2008 Document identifier: SA56004X_5