INTEGRATED CIRCUITS 74F00 Quad 2-input NAND gate Product specification IC15 Data Handbook 1990 Oct 04 Philips Semiconductors Product specification Quad 2-input NAND gate 74F00 FEATURE PIN CONFIGURATION • Industrial temperature range available (–40°C to +85°C) TYPE D0a 1 14 VCC D0b 2 13 D3b TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) Q0 3 12 D3a D1a 4 11 Q3 3.4ns 4.4mA D1b 5 10 D2b Q1 6 9 D2a GND 7 8 Q2 74F00 SF00001 ORDERING INFORMATION ORDER CODE DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C INDUSTRIAL RANGE VCC = 5V ±10%, Tamb = –40°C to +85°C PKG DWG # 14-pin plastic DIP N74F00N I74F00N SOT27-1 14-pin plastic SO N74F00D I74F00D SOT108-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION Dna, Dnb 74F (U.L.) HIGH/LOW Data inputs LOAD VALUE HIGH/LOW 1.0/1.0 20µA/0.6mA Qn Data output 50/33 NOTE: One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state. LOGIC DIAGRAM FUNCTION TABLE 1 D0a D0b 3 2 4 5 D1a D1b 6 9 D2a D2b VCC = Pin 14 GND = Pin 7 1.0mA/20mA 8 10 12 D3a D3b 11 13 INPUTS Q0 Q1 Q2 Q3 SF00002 LOGIC SYMBOL OUTPUT Dna Dnb Qn L L H L H H H L H H H NOTES: H = High voltage level L = Low voltage level L IEC/IEEE SYMBOL 1 & 3 1 2 4 5 9 2 10 12 13 4 6 D0a D0bD1a D1b D2a D2b D3a D3b 5 Q0 Q1 Q2 Q3 10 9 8 12 3 6 8 11 11 13 VCC = Pin 14 GND = Pin 7 SF00003 October 4, 1990 SF00004 2 853-0325 00623 Philips Semiconductors Product specification Quad 2-input NAND gate 74F00 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current VOUT Voltage applied to output in high output state IOUT Current applied to output in low output state Tamb Operating free air temperature range Tstg –30 to +5 mA –0.5 to VCC V 40 mA Commercial range 0 to +70 °C Industrial range –40 to +85 °C –65 to +150 °C Storage temperature range RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNIT MIN NOM MAX VCC Supply voltage 4.5 5.0 5.5 VIH High-level input voltage 2.0 VIL Low-level input voltage 0.8 V IIk Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current Tamb Operating free air temperature range V V 20 mA Commercial range 0 +70 °C Industrial range –40 +85 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) TEST CONDITIONS1 PARAMETER SYMBOL LIMITS MIN VOH VOL High-level output voltage Low-level output voltage TYP2 UNIT MAX VCC = MIN, VIL = MAX ±10%VCC 2.5 VIH = MIN, IOH = MAX ±5%VCC 2.7 VCC = MIN, VIL = MAX ±10%VCC 0.30 0.50 V VIH = MIN, IOl = MAX ±5%VCC 0.30 0.50 V -0.73 -1.2 V 100 µA V 3.4 V VIK Input clamp voltage VCC = MIN, II = IIK II Input current at maximum input voltage VCC = MAX, VI = 7.0V IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V -0.6 mA IOS Short-circuit output current3 VCC = MAX -150 mA ICC Supply current (total) mA -60 ICCH VCC = MAX VIN = GND 1.9 2.8 ICCL VCC = MAX VIN = 4.5V 6.8 10.2 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. October 4, 1990 3 Philips Semiconductors Product specification Quad 2-input NAND gate 74F00 AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL tPLH tPHL PARAMETER Propagation delay Dna, Dnb to Qn VCC = +5.0V ± 10% Tamb = 0°C to +70°C CL = 50pF, RL = 500Ω VCC = +5.0V Tamb = +25°C CL = 50pF, RL = 500Ω TEST CONDITION Waveform 1 VCC = +5.0V ± 10% Tamb = –40°C to +85°C CL = 50pF, RL = 500Ω MIN TYP MAX MIN MAX MIN MAX 2.4 2.0 3.7 3.2 5.0 4.3 2.4 2.0 6.0 5.3 2.0 1.5 6.5 6.0 UNIT ns AC WAVEFORMS For all waveforms, VM = 1.5V. Dna, Dnb VM VM tPHL tPLH VM Qn VM SF00005 Waveform 1. Propagation delay for inverting outputs TEST CIRCUIT AND WAVEFORM VCC VIN tw 90% NEGATIVE PULSE 10% D.U.T. RT CL RL AMP (V) VM VM VOUT PULSE GENERATOR 90% 10% tTHL (tf ) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0V AMP (V) 90% POSITIVE PULSE VM VM 10% Test Circuit for Totem-Pole Outputs DEFINITIONS: RL = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. CL = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. RT = Termination resistance should be equal to ZOUT of pulse generators. 90% 10% tw 0V Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns SF00006 October 4, 1990 4 Philips Semiconductors Product specification Quad 2-input NAND gate 74F00 DIP14: plastic dual in-line package; 14 leads (300 mil) 1990 Oct 04 5 SOT27-1 Philips Semiconductors Product specification Quad 2-input NAND gate 74F00 SO14: plastic small outline package; 14 leads; body width 3.9 mm 1990 Oct 04 6 SOT108-1 Philips Semiconductors Product specification Quad 2-input NAND gate 74F00 NOTES 1990 Oct 04 7 Philips Semiconductors Product specification Quad 2-input NAND gate 74F00 Data sheet status Data sheet status Product status Definition [1] Objective specification Development This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. Preliminary specification Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 print code Document order number: yyyy mmm dd 8 Date of release: 10-98 9397-750-05051