INTEGRATED CIRCUITS XA-G39 XA 16-bit microcontroller family 32K FLASH/1K RAM, watchdog, 2 UARTs Preliminary data 2002 Mar 13 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 • Boot ROM contains low level Flash programming routines for GENERAL DESCRIPTION The XA-G39 is a member of Philips’ 80C51 XA (eXtended Architecture) family of high performance 16-bit single-chip microcontrollers. In-Application Programming and a default serial loader using the UART • 1024 bytes of on-chip data RAM • Supports off-chip program and data addressing up to 1 megabyte The XA-G39 contains 32 kbytes of Flash program memory, and provides three general purpose timers/counters, a watchdog timer, dual UARTs, and four general purpose I/O ports with programmable output configurations. (20 address lines) • Three standard counter/timers with enhanced features (same as XA-G3 T0, T1, and T2). All timers have a toggle output capability A default serial loader program in the Boot ROM allows In-System Programming (ISP) of the Flash memory without the need for a loader in the Flash code. User programs may erase and reprogram the Flash memory at will through the use of standard routines contained in the Boot ROM (In-Application Programming). • Watchdog timer • Two enhanced UARTs with independent baud rates • Seven software interrupts • Four 8-bit I/O ports, with 4 programmable output configurations for each pin FEATURES • 30 MHz operating frequency at 5 V • Power saving operating modes: Idle and Power-Down. • 32 kbytes of on-chip Flash program memory with In-System Programming capability • Three Flash blocks = two 8 kbyte blocks and one 16 kbyte block • Provides Flash solution for XA-G37 (OTP) designs • Single supply voltage In-System Programming (ISP) of the Flash Wake-Up from power-down via an external interrupt is supported. • 44-pin PLCC package memory (VPP = VDD, or VPP = 12 V if desired) BLOCK DIAGRAM XA CPU Core Program Memory Bus SFR bus UART 0 32 KBYTES FLASH 1024 BYTES STATIC RAM Data Bus UART 1 TIMER 0, 1 PORT 0 PORT 1 TIMER 2 PORT 2 WATCHDOG TIMER PORT 3 SU01594 2002 Mar 13 2 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 ORDERING INFORMATION FLASH TEMPERATURE RANGE (°C) AND PACKAGE FREQ. (MHz) DRAWING NUMBER PXAG39KBA 0 to +70 44-pin Plastic Leaded Chip Carrier 30 SOT187-2 LOGIC SYMBOL VDD VSS XTAL1 XTAL2 RXD1 A3 A2 A1 A0/WRH ADDRESS BUS PORT 1 T2EX T2 TXD1 RST EA/WAIT PORT 0 RxD0 TxD0 INT0 INT1 T0 T1/BUSW WRL RD PORT 3 ALTERNATE FUNCTIONS ALE ADDRESS AND DATA BUS PORT 2 PSEN SU01588 2002 Mar 13 3 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs PINNING INFORMATION 44-Pin PLCC Package 6 1 40 7 39 PLCC 17 29 18 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 2002 Mar 13 Function VSS P1.0/A0/WRH P1.1/A1 P1.2/A2 P1.3/A3 P1.4/RxD1 P1.5/TxD1 P1.6/T2 P1.7/T2EX RST P3.0/RxD0 NC P3.1/TxD0 P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1/BUSW P3.6/WRL P3.7/RD XTAL2 XTAL1 VSS 28 Pin 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Function VDD P2.0/A12D8 P2.1/A13D9 P2.2/A14D10 P2.3/A15D11 P2.4/A16D12 P2.5/A17D13 P2.6/A18D14 P2.7/A19D15 PSEN ALE NC EA/VPP/WAIT P0.7/A11D7 P0.6/A10D6 P0.5/A9D5 P0.4/A8D4 P0.3/A7D3 P0.2/A6D2 P0.1/A5D1 P0.0/A4D0 VDD SU01035 4 XA-G39 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 PIN DESCRIPTION MNEMONIC PIN NO. TYPE NAME AND FUNCTION VSS 1, 22 I Ground: 0 V reference. VDD 23, 44 I Power Supply: This is the power supply voltage for normal, idle, and power down operation. P0.0 – P0.7 43–36 I/O Port 0: Port 0 is an 8-bit I/O port with a user-configurable output type. Port 0 latches have 1s written to them and are configured in the quasi-bidirectional mode during reset. The operation of port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for details. When the external program/data bus is used, Port 0 becomes the multiplexed low data/instruction byte and address lines 4 through 11. P1.0 – P1.7 P2.0 – P2.7 2–9 I/O 2 O 3 4 5 6 7 8 9 O O O I O I/O I 24–31 I/O Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type. Port 1 latches have 1s written to them and are configured in the quasi-bidirectional mode during reset. The operation of port 1 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for details. Port 1 also provides special functions as described below. A0/WRH: Address bit 0 of the external address bus when the external data bus is configured for an 8 bit width. When the external data bus is configured for a 16 bit width, this pin becomes the high byte write strobe. A1: Address bit 1 of the external address bus. A2: Address bit 2 of the external address bus. A3: Address bit 3 of the external address bus. RxD1 (P1.4): Receiver input for serial port 1. TxD1 (P1.5): Transmitter output for serial port 1. T2 (P1.6): Timer/counter 2 external count input/clockout. T2EX (P1.7): Timer/counter 2 reload/capture/direction control Port 2: Port 2 is an 8-bit I/O port with a user-configurable output type. Port 2 latches have 1s written to them and are configured in the quasi-bidirectional mode during reset. The operation of port 2 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for details. When the external program/data bus is used in 16-bit mode, Port 2 becomes the multiplexed high data/instruction byte and address lines 12 through 19. When the external program/data bus is used in 8-bit mode, the number of address lines that appear on port 2 is user programmable. P3.0 – P3.7 11, 13–19 I/O 11 13 14 15 16 17 I O I I I/O I/O 18 19 O O RST 10 I ALE 33 I/O 2002 Mar 13 Port 3: Port 3 is an 8-bit I/O port with a user configurable output type. Port 3 latches have 1s written to them and are configured in the quasi-bidirectional mode during reset. the operation of port 3 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for details. Port 3 also provides various special functions as described below. RxD0 (P3.0): Receiver input for serial port 0. TxD0 (P3.1): Transmitter output for serial port 0. INT0 (P3.2): External interrupt 0 input. INT1 (P3.3): External interrupt 1 input. T0 (P3.4): Timer 0 external input, or timer 0 overflow output. T1/BUSW (P3.5): Timer 1 external input, or timer 1 overflow output. The value on this pin is latched as the external reset input is released and defines the default external data bus width (BUSW). 0 = 8-bit bus and 1 = 16-bit bus. WRL (P3.6): External data memory low byte write strobe. RD (P3.7): External data memory read strobe. Reset: A low on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor to begin execution at the address contained in the reset vector. Refer to the section on Reset for details. Address Latch Enable: A high output on the ALE pin signals external circuitry to latch the address portion of the multiplexed address/data bus. A pulse on ALE occurs only when it is needed in order to process a bus cycle. 5 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 MNEMONIC PIN NO. TYPE NAME AND FUNCTION PSEN 32 O Program Store Enable: The read strobe for external program memory. When the microcontroller accesses external program memory, PSEN is driven low in order to enable memory devices. PSEN is only active when external code accesses are performed. EA/WAIT/ VPP 35 I External Access/Wait/Programming Supply Voltage: The EA input determines whether the internal program memory of the microcontroller is used for code execution. The value on the EA pin is latched as the external reset input is released and applies during later execution. When latched as a 0, external program memory is used exclusively, when latched as a 1, internal program memory will be used up to its limit, and external program memory used above that point. After reset is released, this pin takes on the function of bus Wait input. If Wait is asserted high during any external bus access, that cycle will be extended until Wait is released. During EPROM programming, this pin is also the programming supply voltage input. XTAL1 21 I Crystal 1: Input to the inverting amplifier used in the oscillator circuit and input to the internal clock generator circuits. XTAL2 20 O Crystal 2: Output from the oscillator amplifier. SPECIAL FUNCTION REGISTERS NAME DESCRIPTION BIT FUNCTIONS AND ADDRESSES SFR ADDRESS MSB LSB RESET VALUE AUXR Auxiliary function register 44C ENBOOT FMIDLE PWR_VLD — — — — — BCR Bus configuration register 46A — — — WAITD BUSD BC2 BC1 BC0 BTRH Bus timing register high byte 469 DW1 DW0 DWA1 DWA0 DR1 DR0 DRA1 DRA0 FF BTRL Bus timing register low byte 468 WM1 WM0 ALEW — CR1 CR0 CRA1 CRA0 EF CS DS ES Code segment Data segment Extra segment 443 441 442 00 00 00 33F IEH* Interrupt enable high byte 427 Note 1 33E 33D 33C 33B 33A 339 338 — — — — ETI1 ERI1 ETI0 ERI0 337 336 335 334 333 332 331 330 — — ET2 ET1 EX1 ET0 EX0 00 IEL* Interrupt enable low byte 426 EA IPA0 Interrupt priority 0 4A0 — PT0 — PX0 00 IPA1 Interrupt priority 1 4A1 — PT1 — PX1 00 IPA2 Interrupt priority 2 4A2 — — — PT2 00 IPA4 Interrupt priority 4 4A4 — PTI0 — PRI0 00 IPA5 Interrupt priority 5 4A5 — PTI1 — PRI1 00 P0* P1* P2* P3* Port 0 Port 1 Port 2 Port 3 2002 Mar 13 430 431 432 433 387 386 385 384 383 382 381 380 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 38F 38E 38D 38C 38B 38A 389 388 T2EX T2 TxD1 RxD1 A3 A2 A1 WRH 397 396 395 394 393 392 391 390 P2.7 P2.6 P2.5 P2.4 P2.3 P2.2 P2.1 P2.0 39F 39E 39D 39C 39B 39A 399 398 RD WR T1 T0 INT1 INT0 TxD0 RxD0 6 00 FF FF FF FF Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs DESCRIPTION NAME SFR ADDRESS XA-G39 BIT FUNCTIONS AND ADDRESSES MSB LSB RESET VALUE P0CFGA Port 0 configuration A 470 Note 5 P1CFGA Port 1 configuration A 471 Note 5 P2CFGA Port 2 configuration A 472 Note 5 P3CFGA Port 3 configuration A 473 Note 5 P0CFGB Port 0 configuration B 4F0 Note 5 P1CFGB Port 1 configuration B 4F1 Note 5 P2CFGB Port 2 configuration B 4F2 Note 5 P3CFGB Port 3 configuration B 4F3 Note 5 PCON* Power control register 404 PSWH* Program status word (high byte) 401 PSWL* Program status word (low byte) 400 227 226 225 224 223 222 221 220 — — — — — — PD IDL 20F 20E 20D 20C 20B 20A 209 208 SM TM RS1 RS0 IM3 IM2 IM1 IM0 207 206 205 204 203 202 201 200 C AC — — — V N Z 217 216 215 214 213 212 211 210 C AC F0 RS1 RS0 V F1 P 00 Note 2 Note 2 PSW51* 80C51 compatible PSW 402 RTH0 Timer 0 extended reload, high byte Timer 1 extended reload, high byte Timer 0 extended reload, low byte Timer 1 extended reload, low byte 455 00 457 00 454 00 456 00 RTH1 RTL0 RTL1 S0CON* Serial port 0 control register 420 307 306 305 304 303 302 301 300 SM0_0 SM1_0 SM2_0 REN_0 TB8_0 RB8_0 TI_0 RI_0 30F 30E 30D 30C 30B 30A 309 308 — — — — FE0 BR0 OE0 STINT0 Note 3 00 S0STAT* Serial port 0 extended status 421 S0BUF S0ADDR S0ADEN Serial port 0 buffer register Serial port 0 address register Serial port 0 address enable register 460 461 462 S1CON* Serial port 1 control register 424 S1STAT* Serial port 1 extended status 425 S1BUF S1ADDR S1ADEN Serial port 1 buffer register Serial port 1 address register Serial port 1 address enable register 464 465 466 SCR System configuration register 440 — 21F 21E 21D 21C 21B 21A 219 218 SSEL* Segment selection register 403 ESWEN R6SEG R5SEG R4SEG R3SEG R2SEG R1SEG R0SEG 00 SWE Software Interrupt Enable 47A — SWE7 SWE6 SWE5 SWE4 SWE3 SWE2 SWE1 00 2002 Mar 13 00 x 00 00 327 326 325 324 323 322 321 320 SM0_1 SM1_1 SM2_1 REN_1 TB8_1 RB8_1 TI_1 RI_1 32F 32E 32D 32C 32B 32A 329 328 — — — — FE1 BR1 OE1 STINT1 00 00 x 00 00 — 7 — — PT1 PT0 CM PZ 00 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs DESCRIPTION NAME SFR ADDRESS XA-G39 BIT FUNCTIONS AND ADDRESSES MSB LSB 357 356 355 354 353 352 351 350 — SWR7 SWR6 SWR5 SWR4 SWR3 SWR2 SWR1 RESET VALUE SWR* Software Interrupt Request 42A T2CON* Timer 2 control register 418 T2MOD* Timer 2 mode control 419 TH2 TL2 T2CAPH Timer 2 high byte Timer 2 low byte Timer 2 capture register, high byte Timer 2 capture register, low byte 459 458 45B 00 00 00 45A 00 T2CAPL 2C7 2C6 2C5 2C4 2C3 2C2 2C1 2C0 TF2 EXF2 RCLK0 TCLK0 EXEN2 TR2 C/T2 CP/RL2 2CF 2CE 2CD 2CC 2CB 2CA 2C9 2C8 — — RCLK1 TCLK1 — — T2OE DCEN 287 286 285 284 283 282 281 280 TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 TCON* Timer 0 and 1 control register 410 TH0 TH1 TL0 TL1 Timer 0 high byte Timer 1 high byte Timer 0 low byte Timer 1 low byte 451 453 450 452 TMOD Timer 0 and 1 mode control 45C TSTAT* Timer 0 and 1 extended status 411 2FF WDCON* Watchdog control register 41F PRE2 WDL Watchdog timer reload Watchdog feed 1 Watchdog feed 2 45F 45D 45E WFEED1 WFEED2 00 00 00 00 00 00 00 00 GATE C/T M1 M0 GATE C/T M1 28F 28E 28D 28C — — — — 2FE 2FD 2FC 2FB PRE1 PRE0 — — M0 28B 28A 289 288 — T1OE — T0OE 2FA 2F9 2F8 WDRUN WDTOF — 00 00 Note 6 00 x x NOTES: * SFRs are bit addressable. 1. At reset, the BCR register is loaded with the binary value 0000 0a11, where “a” is the value on the BUSW pin. This defaults the address bus size to 20 bits since the XA-G39 has only 20 address lines. 2. SFR is loaded from the reset vector. 3. All bits except F1, F0, and P are loaded from the reset vector. Those bits are all 0. 4. Unimplemented bits in SFRs are X (unknown) at all times. Ones should not be written to these bits since they may be used for other purposes in future XA derivatives. The reset value shown for these bits is 0. 5. Port configurations default to quasi-bidirectional when the XA begins execution from internal code memory after reset, based on the condition found on the EA pin. Thus all PnCFGA registers will contain FF and PnCFGB registers will contain 00. When the XA begins execution using external code memory, the default configuration for pins that are associated with the external bus will be push-pull. The PnCFGA and PnCFGB register contents will reflect this difference. 6. The WDCON reset value is E6 for a Watchdog reset, E4 for all other reset causes. 7. The XA-G39 implements an 8-bit SFR bus, as stated in Chapter 8 of the XA User Guide. All SFR accesses must be 8-bit operations. Attempts to write 16 bits to an SFR will actually write only the lower 8 bits. Sixteen bit SFR reads will return undefined data in the upper byte. 8. The AUXR reset value is typically 00h. If the Boot Loader is activated at reset because the Flash status byte is non-zero or because the Boot Vector has been forced (by PSEN = 0, ALE = 1, EA = 1 at reset), the AUXR reset value will be 1x00 0000b. Bit 6 will be a 1 if the on-chip VPP generator is running and ready, otherwise it will be a 0. 2002 Mar 13 8 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 FFFFFh UP TO 1 MBYTE TOTAL CODE MEMORY FFFFh 2 KBYTES BOOT ROM F800h 8000h 7FFFh 32 KBYTES ON-CHIP CODE MEMORY 0000h Note: The Boot ROM is enabled via the ENBOOT bit in register AUXR. SU01589 Figure 1. XA-G39 Program Memory Map Data Segment 0 Other Data Segments FFFFFh FFFFFh DATA MEMORY (INDIRECTLY ADDRESSED, OFF-CHIP) 1 KBYTE ON-CHIP DATA MEMORY (RAM) DATA MEMORY (INDIRECTLY ADDRESSED, OFF-CHIP) 0400H 0400H 03FFh 03FFh DATA MEMORY (DIRECTLY AND INDIRECTLY ADDRESSABLE, OFF-CHIP) DATA MEMORY (DIRECTLY AND INDIRECTLY ADDRESSABLE, ON CHIP) 0040h BIT-ADDRESSABLE DATA AREA DATA MEMORY (DIRECTLY AND INDIRECTLY ADDRESSABLE, ON CHIP) DIRECTLY ADDRESSED DATA (1k PER SEGMENT) 0040h 003Fh 003Fh 0020h 0020h 001Fh 001Fh 0000h 0000h BIT-ADDRESSABLE DATA AREA DATA MEMORY (DIRECTLY AND INDIRECTLY ADDRESSABLE, OFF-CHIP) SU01590 Figure 2. XA-G39 Data Memory Map 2002 Mar 13 9 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs FLASH EPROM MEMORY CAPABILITIES OF THE PHILIPS XA-G39 FLASH-BASED MICROCONTROLLERS GENERAL DESCRIPTION Flash organization The XA-G39 Flash memory augments EPROM functionality with in-circuit electrical erasure and programming. The Flash can be read and written as bytes. The Chip Erase operation will erase the entire program memory. The Block Erase function can erase any single Flash block. In-circuit programming and standard parallel programming are both available. On-chip erase and write timing generation contribute to a user friendly programming interface. The XA-G39 contains 32 kbytes of Flash program memory. This memory is organized as 3 separate blocks. The first two blocks are 8 kbytes in size, filling the program memory space from address 0 through 3FFF hex. The final block is 16 kbytes in size and occupies addresses 4000 through 7FFF hex. Figure 3 depicts the Flash memory configuration. The XA-G39 Flash reliably stores memory contents even after 10,000 erase and program cycles. The cell is designed to optimize the erase and programming mechanisms. In addition, the combination of advanced tunnel oxide processing and low internal electric fields for erase and programming operations produces reliable cycling. For In-System Programming, the XA-G39 can use a single +5 V power supply. Faster In-System Programming may be obtained, if required, through the use of a +12 V VPP supply. Parallel programming (using separate programming hardware) uses a +12 V VPP supply. Flash Programming and Erasure The XA-G39 Flash microcontroller supports a number of programming possibilities for the on-chip Flash memory. The Flash memory may be programmed in a parallel fashion on standard programming equipment in a manner similar to an EPROM microcontroller. The XA-G39 microcontroller is able to program its own Flash memory while the application code is running. Also, a default loader built into a Boot ROM allows programming blank devices serially through the UART. Using any of these types of programming, any of the individual blocks may be erased separately, or the entire chip may be erased. Programming of the Flash memory is accomplished one byte at a time. FEATURES • Flash EPROM internal program memory with Single Voltage Boot ROM Programming and Block Erase capability. When the microcontroller programs its own Flash memory, all of the low level details are handled by code that is permanently contained in a 2 kbyte “Boot ROM” that is separate from the Flash memory. A user program simply calls the entry point with the appropriate parameters to accomplish the desired operation. Boot ROM operations include things like: erase block, program byte, verify byte, program security lock bit, etc. The Boot ROM overlays the program memory space from F800 to FFFF hex, when it is enabled by setting the ENBOOT bit at AUXR.7. The Boot ROM may be turned off so that the underlying address space becomes available. • Internal 2 kbyte fixed boot ROM, containing low-level programming routines and a default loader. The Boot ROM can be turned on and off via ENBOOT in the AUXR register. • The boot vector allows a user provided Flash loader code to reside anywhere in the Flash memory space. This configuration provides flexibility to the user. • The default loader in Boot ROM allows programming via the serial port without the need for a user-provided loader. • Up to 1 Mbyte external program memory if the internal program ENBOOT and PWR_VLD Setting the ENBOOT bit in the AUXR register enables the Boot ROM and activates the on-chip VPP generator if VPP is connected to VDD rather than 12 V externally. The PWR_VLD flag indicates that VPP is available for programming and erase operations. This flag should be checked prior to calling the Boot ROM for programming and erase services. When ENBOOT is set, it typically takes 5 microseconds for the internal programming voltage to be ready. memory is disabled (EA = 0). • Programming and erase voltage: VPP = VDD (5 V power supply), or 12 V ±5% for In System Programming. Using 12 V VPP for ISP improves programming and erase time. • Read/Programming/Erase in ISP: – Byte-wise read (60 ns access time at 4.5 V). The ENBOOT bit will automatically be set if the status byte is non-zero during reset, or when PSEN is low, ALE is high, and EA is high at the falling edge of reset. Otherwise, ENBOOT will be cleared during reset. – Byte Programming (0.5–1 minute for 32 K flash, depending on clock frequency). • In-circuit programming via user selected method, typically RS232 or parallel I/O port interface. • Programmable security for the code in the Flash. • 10,000 minimum erase/program cycles each byte over operating When programming functions are not needed, ENBOOT may be cleared. This enables access to the 2 kbytes of Flash code memory that is overlaid by the Boot ROM, allowing a full 32 kbytes of Flash code memory. temperature range. • 10 year minimum data retention. 2002 Mar 13 XA-G39 10 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 7FFF BLOCK 2 16 KBYTES PROGRAM ADDRESS 4000 BLOCK 1 8 KBYTES 2000 BLOCK 0 8 KBYTES 0000 SU01591 Figure 3. Flash Memory Configuration Program Counter (BPC) and the Boot PSW (BPSW). The factory default settings are 8000h for the BPSW and F800h for the BPC, which corresponds to the address F900h for the factory masked-ROM ISP boot loader. The Status Byte is automatically set to a non-zero value when a programming error occurs. A custom boot loader can be written with the Boot Vector set to the custom boot loader. FMIDLE The FMIDLE bit in the AUXR register allows saving additional power by turning off the Flash memory when the CPU is in the Idle mode. This must be done just prior to initiating the Idle mode, as shown below. OR AUXR,#$40 OR . PCON,#$01 . ; Set Flash memory to idle mode. ; Turn on Idle mode. ; Execution resumes here when Idle mode terminates. NOTE: When erasing the Status Byte or Boot Vector, these bytes are erased at the same time. It is necessary to reprogram the Boot Vector after erasing and updating the Status Byte. Hardware Activation of the Boot Vector Program execution at the Boot Vector may also be forced from outside of the microcontroller by setting the correct state on a few pins. While Reset is asserted, the PSEN pin must be pulled low, the ALE pin allowed to float high (need not be pulled up externally), and the EA pin driven to a logic high (or up to VPP). Then reset may be released. This is the same effect as having a non-zero status byte. This allows building an application that will normally execute the end user’s code but can be manually forced into ISP operation. The Boot ROM is enabled when use of the Boot Vector is forced as described above, so the branch may go to the default loader. Conversely, user code in the program memory space from F800h to FFFFh may not be executed when the Boot Vector is used. When the Flash memory is put into the Idle mode by setting FMIDLE, restarting the CPU upon exiting Idle mode takes slightly longer, about 3 microseconds. However, the standby current consumed by the Flash memory is reduced from about 8mA to about 1mA. Default Loader A default loader that accepts programming commands in a predetermined format is contained permanently in the Boot ROM. A factory fresh device will enter this loader automatically if it is powered up without first being programmed by the user. Loader commands include functions such as erase block; program Flash memory; read Flash memory; and blank check. If the factory default setting for the BPC (F800h) is changed, it will no longer point to the ISP masked-ROM boot loader code. If this happens, the only possible way to change the contents of the Boot Vector is through the parallel programming method, provided that the end user application does not contain a customized loader that provides for erasing and reprogramming of the Boot Vector and Status Byte. Boot Vector The XA-G39 contains two special FLASH registers: the BOOT VECTOR and the STATUS BYTE. The “Boot Vector” allows forcing the execution of a user supplied Flash loader upon reset, under two specific sets of conditions. At the falling edge of reset, the XA-G39 examines the contents of the Status Byte. If the Status Byte is set to zero, power-up execution starts at location 0000H, which is the normal start address of the user’s application code. After programming the FLASH, the status byte should be erased to zero in order to allow execution of the user’s application code beginning at address 0000H. When the Status Byte is set to a value other than zero, the Boot Vector is used as the reset vector (4 bytes), including the Boot 2002 Mar 13 11 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 VCC VPP VDD SUPPLY OR +12V ±5% FOR USE WITH WINISP OR FLASHMAGIC VDD 5V ±5% TxD TxD 2 RxD RxD 3 RST XTAL2 VSS RS-232 TRANSCEIVER MC145406, MAX232, OR EQUIVALENT 5 FEMALE DB-9 XTAL1 VSS SU01593 Figure 4. In-System Programming with a Minimum of Pins There is also an application note available that deals with In-System Programming (AN716). At www.philipsmcu.com, search for “ISP”, then select AN716 from the search results. In-System Programming (ISP) In-System Programming (ISP) is performed without removing the microcontroller from the system. The In-System Programming (ISP) facility consists of a series of internal hardware resources coupled with internal firmware to facilitate remote programming of the XA-G39 through the serial port. This firmware is provided by Philips and embedded within each XA-G39 device. Using In-System Programming (ISP) ISP mode is entered by holding PSEN low, asserting, un-asserting RESET, then releasing PSEN. When ISP mode is entered, the default loader first disables the watchdog timer to prevent a watchdog reset from occurring during programming. The Philips In-System Programming (ISP) facility has made in-circuit programming in an embedded application possible with a minimum of additional expense in components and circuit board area. The ISP feature allows for a wide range of baud rates to be used in the application, independent of the oscillator frequency. It is also adaptable to a wide range of oscillator frequencies. This is accomplished by measuring the bit-time of a single bit in a received character. This information is then used to program the baud rate in terms of timer counts based on the oscillator frequency. The ISP feature requires that an initial character (a lowercase f) be sent to the XA-G39 to establish the baud rate. The ISP firmware provides auto-echo of received characters. The ISP function uses five pins: TxD, RxD, VSS, VDD, and VPP (see Figure 4). Only a small connector needs to be available to interface your application to an external circuit in order to use this feature. The VPP supply should be adequately decoupled and VPP not allowed to exceed datasheet limits. VCC VPP OSC FREQ IDD 5.0 V 5.0 V 22 MHz 75 mA typical 5.0 V 5.0 V 30 MHz 90 mA typical Once baud rate initialization has been performed, the ISP firmware will only accept specific Intel Hex-type records. Intel Hex records consist of ASCII characters used to represent hexadecimal values and are summarized below: ISP increases IDD by less than 1mA. :NNAAAARRDD..DDCC<crlf> Free ISP software is available on the Philips web site: “WinISP” In the Intel Hex record, the “NN” represents the number of data bytes in the record. The XA-G39 will accept up to 16 (10H) data bytes. The “AAAA” string represents the address of the first byte in the record. If there are zero bytes in the record, this field is often set to 0000. The “RR” string indicates the record type. A record type of “00” is a data record. A record type of “01” indicates the end-of-file mark. In this application, additional record types will be added to indicate either commands or data for the ISP facility. The maximum number of data bytes in a record is limited to 16 (decimal). ISP commands are summarized in Table 1. 1. Direct your browser to the following page: http://www.semiconductors.com/mcu/download/80C51/flash/ 2. Download “WinISP.exe” 3. Execute WinISP.exe to install the software Free ISP software is also available from the Embedded Systems Academy: “FlashMagic” 1. Direct your browser to the following page: http://www.esacademy.com/software/flashmagic/ As a record is received by the XA-G39, the information in the record is stored internally and a checksum calculation is performed. The 2. Download Flashmagic 3. Execute “flashmagic.exe” to install the software 2002 Mar 13 12 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs RS-232, serially using some other method, or even parallel over a user defined I/O port. The user has the freedom to choose a method that does not interfere with the application circuit. As an added feature, the application program may also use the Flash memory as a long term data storage, saving configuration information, sensor readings, or any other desired data. operation indicated by the record type is not performed until the entire record has been received. Should an error occur in the checksum, the XA-G39 will send an “X” out the serial port indicating a checksum error. If the checksum calculation is found to match the checksum in the record, then the command will be executed. In most cases, successful reception of the record will be indicated by transmitting a “.” character out the serial port (displaying the contents of the internal program memory is an exception). The actual loader code would typically be programmed by the user into the microcontroller in a parallel fashion or via the default loader during their manufacturing process. The entire initial Flash contents may be programmed at that time, or the rest of the application may be programmed into the Flash memory at a later time, possibly using the loader code to do the programming. In the case of a Data Record (record type 00), an additional check is made. A “.” character will NOT be sent unless the record checksum matched the calculated checksum and all of the bytes in the record were successfully programmed. For a data record, an “X” indicates that the checksum failed to match, and an “R” character indicates that one of the bytes did not properly program. This application controlled programming capability allows for the possibility of changing the application code in the field. If the application circuit is embedded in a PC, or has a way to establish a telephone data link to a user’s or manufacturer’s computer, new code could be downloaded from diskette or a manufacturer’s support system. There is even the possibility of conducting very specialized remote testing of a failing circuit board by the manufacturer by remotely programming a series of detailed test programs into the application board and checking the results. The ISP facility was designed so that specific crystal frequencies were not required in order to generate baud rates or time the programming pulses. User Supplied Loader A user program can simply decide at any time, for any reason, to begin Flash programming operations. All it has to do in advance is to instruct external circuitry to apply +5 V or +12 V to the VPP pin, and make certain that the Boot ROM is enabled. User code may contain a loader designed to replace the application code contained in the Flash memory by loading new code through any communication medium available in the application. This is completely flexible and defined by the designer of the system. It could be done serially using 2002 Mar 13 XA-G39 Any user supplied loader should take the watchdog timer into account. Typically, the watchdog timer would be disabled upon entry to the loader if it might be running, in order to prevent a watchdog reset from occurring during programming. 13 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs Table 1. Intel-Hex Records Used by In-System Programming RECORD TYPE 00 or 80 COMMAND/DATA FUNCTION Data Record :nnaaaa00dd....ddcc Where: Nn Aaaa dd....dd cc = = = = number of bytes (hex) in record memory address of first byte in record data bytes checksum Example: :10008000AF5F67F0602703E0322CFA92007780C3FD 01 or 81 End of File (EOF), no operation :xxxxxx01cc Where: xxxxxx cc = required field, but value is a “don’t care” = checksum Example: :00000001FF 83 Miscellaneous Write Functions :nnxxxx83ffssddcc Where: nn xxxx 83 ff ss dd cc = = = = = = = number of bytes (hex) in record required field, but value is a “don’t care” Write Function subfunction code selection code data input (as needed) checksum Subfunction Code = 01 (Erase Blocks) ff = 01 ss = block number in bits 7:5, Bits 4:0 = zeros block 0 : ss = 00h block 1 : ss = 20h block 2 : ss = 40h Example: :0200008301203C erase block 1 Subfunction Code = 04 (Erase Boot Vector and Status Byte) ff = 04 ss = don’t care dd = don’t care Example: :010000830478 erase boot vector and status byte Subfunction Code = 05 (Program Security Bits) ff = 05 ss = 00 program security bit 1 (inhibit writing to FLASH) 01 program security bit 2 (inhibit FLASH verify) 02 program security bit 3 (disable external memory) Example: :02000083050175 program security bit 2 Subfunction Code = 06 (Program Status Byte or Boot Vector) ff = 06 ss = 00 program status byte 01 program boot vector NOTE: Only two bits of these Special Cells may be programmed at one time. Example: :020000830601FC78 2002 Mar 13 program boot vector to FC00h 14 XA-G39 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs RECORD TYPE 84 XA-G39 COMMAND/DATA FUNCTION Display Device Data or Blank Check – Record type 84 causes the contents of the entire FLASH array to be sent out the serial port in a formatted display. This display consists of an address and the contents of 16 bytes starting with that address. No display of the device contents will occur if security bit 2 has been programmed. The dumping of the device data to the serial port is terminated by the reception of any character. General Format of Function 84 :05xxxx84sssseeeeffcc Where: 05 xxxx 84 ssss eeee ff cc = = = = = = number of bytes (hex) in record required field, but value is a “don’t care” “Display Device Data or Blank Check” function code starting address ending address subfunction 00 = display data 01 = blank check = checksum Example: :0500008440004FFF00E9 85 display 4000–4FFF Miscellaneous Read Functions General Format of Function 85 :02xxxx85ffsscc Where: 02 xxxx 85 ffss cc = = = = number of bytes (hex) in record required field, but value is a “don’t care” “Miscellaneous Read” function code subfunction and selection code 0000 = read signature byte – manufacturer id (15H) 0001 = read signature byte – device id # 1 (EAH) 0002 = read signature byte – device id # 2 (XA–G39 = 65H)) 0700 = read security bits (returned value bits 3:1 = sb3,sb2,sb1) 0701 = read status byte 0702 = read boot vector = checksum Example: :02000085000178 2002 Mar 13 read signature byte – device id # 1 15 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 common interface, PGM_MTP. The programming functions are selected by setting up the microcontroller’s registers before making a call to PGM_MTP at FFF0H. Results are returned in the registers. The IAP calls are shown in Table 2. In-Application Programming Method Several In-Application Programming (IAP) calls are available for use by an application program to permit selective erasing and programming of FLASH sectors. All calls are made through a Table 2. IAP calls IAP CALL PARAMETER PROGRAM DATA BYTE Input Parameters: R0H = 02h or 92h R6 = address of byte to program R4L = byte to program Return Parameter R4L = 00 if pass, non-zero if fail ERASE BLOCK Input Parameters: R0H = 01h or 93h R6H = block number in bits 7:5, bits 4:0 = ’0’ block 0 : R6H = 00h block 1 : R6H = 20h block 2 : R6H = 40h R6L = 00h Return Parameter R4L = 00 if pass, non-zero if fail ERASE BPC and STATUS BYTE Input Parameters: R0H = 04h Return Parameter R4L = 00 if pass, non-zero if fail PROGRAM SECURITY BIT Input Parameters: R0H = 05h R6H = 00h R6L = 00h – security bit # 1 (inhibit writing to FLASH) 01h – security bit # 2 (inhibit FLASH verify) 02h – security bit # 3 (disable external memory) Return Parameter none PROGRAM STATUS BYTE Input Parameters: R0H = 06h R6H = 00h R6L = 00h – program status byte R4L = status byte Return Parameter R4L = 00 if pass, non-zero if fail NOTE: Only two bits of this Special Cell may be programmed at one time. PROGRAM BPC high byte Input Parameters: R0H = 06h R6H = 00h R6L = 01h – program BPC R4L = BPC[15:8] (BPC[7:0] unchanged) Return Parameter R4L = 00 if pass, non-zero if fail NOTE: Only two bits of this Special Cell may be programmed at one time. READ DEVICE DATA Input Parameters: R0H = 03h R6 = address of byte to read Return Parameter R4L = value of byte read READ MANUFACTURER ID Input Parameters: R0H = 00h R6H = 00h R6L = 00h (manufacturer ID) Return Parameter R4L = value of byte read 2002 Mar 13 16 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs IAP CALL XA-G39 PARAMETER READ DEVICE ID # 1 Input Parameters: R0H = 00h R6H = 00h R6L = 01h (device ID # 1) Return Parameter R4L = value of byte read READ DEVICE ID # 2 Input Parameters: R0H = 00h R6H = 00h R6L = 02h (device ID # 2) Return Parameter R4L = value of byte read READ SECURITY BITS Input Parameters: R0H = 07h R6H = 00h R6L = 00h (security bits) Return Parameter R4L = value of byte read R4L[3:1] = sb3, sb2, sb1 READ STATUS BYTE Input Parameters: R0H = 07h R6H = 00h R6L = 01h (status byte) Return Parameter R4L = value of BPC[15:8] READ BPC Input Parameters: R0H = 07h R6H = 00h R6L = 02h (boot vector) Return Parameter R4L = value of byte read (high byte of Boot PC) PROGRAM ALL ZERO Input Parameters: R0H = 90h R6H = block number in bits 7:5, bits 4:0 = ‘0’ block 0 : r6h = 00h block 1 : r6h = 20h block 2 : r6h = 40h R6L = 00h Return Parameters: R4L = 00 if pass, non–zero if fail ERASE CHIP Input Parameters: R0H = 91h R4L = 55h (after chip erase, return to caller) = AAh (after chip erase, reset chip) = others: error Return Parameters: R4L = 00 if pass, non–zero if fail PROGRAM SPECIAL CELL Input Parameters: R0H = 94h R6 = special cell address 0000h: program BPSW[7:0] 0001h: program BPSW[15:8] 0002h: program BPC[7:0] 0003h: program BPC[15:8] 0004h: program status byte 000Ah: program security bit #1 000Ch: program security bit #2 000Eh: program security bit #3 R4L = byte value to program Return Parameters: R4L = 00 if pass, non–zero if fail NOTE: Only two bits of these Special Cells may be programmed at one time. 2002 Mar 13 17 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs IAP CALL XA-G39 PARAMETER ERASE SPECIAL CELL Input Parameters: R0H = 95h R6 = special cell address 0000h: erase BPSW[7:0] 0001h: erase BPSW[15:8] 0002h: erase BPC[7:0] 0003h: erase BPC[15:8] 0004h: erase status byte Return Parameters: R4L = 00 if pass, non–zero if fail READ SPECIAL CELL Input Parameters: R0H = 96h R6 = special cell address 0000h: read BPSW[7:0] 0001h: read BPSW[15:8] 0002h: read BPC[7:0] 0003h: read BPC[15:8] 0004h: read status byte 0006h: read manufacturer 0007h: read device ID #1 0008h: read device ID #2 000Ah: read security bit 000Ch: read security bit 000Eh: read security bit Return Parameters: R4L = value of byte read ID #1 #2 #3 Security The security feature protects against software piracy and prevents the contents of the Flash from being read. The Security Lock bits are located in Flash. The XA-G39 has 3 programmable security lock bits that will provide different levels of protection for the on-chip code and data (see Table 3). Table 3. SECURITY LOCK BITS1 PROTECTION DESCRIPTION Level SB1 SB2 SB3 1 0 0 0 No program security features enabled. 2 1 0 0 Same as level 1, plus block erase is disabled. Erase or programming of the status byte or boot vector is disabled. 3 1 1 0 Same as level 2, plus program verification is disabled 4 1 1 1 Same as level 3, plus external execution is disabled. NOTE: 1. Any other combination of the Lock bits is not defined. 2. Security bits are independent of each other. Full-chip erase may be performed regardless of the states of the security bits. 3. Setting LB doesn’t prevent programming of unprogrammed bits. 2002 Mar 13 18 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs generation, Timer 2 capture. Note that this single rate setting applies to all of the timers. XA-G39 TIMER/COUNTERS The XA has two standard 16-bit enhanced Timer/Counters: Timer 0 and Timer 1. Additionally, it has a third 16-bit Up/Down timer/counter, T2. A central timing generator in the XA core provides the time-base for all XA Timers and Counters. The timer/event counters can perform the following functions: – Measure time intervals and pulse duration – Count external events – Generate interrupt requests – Generate PWM or timed output waveforms When timers T0, T1, or T2 are used in the counter mode, the register will increment whenever a falling edge (high to low transition) is detected on the external input pin corresponding to the timer clock. These inputs are sampled once every 2 oscillator cycles, so it can take as many as 4 oscillator cycles to detect a transition. Thus the maximum count rate that can be supported is Osc/4. The duty cycle of the timer clock inputs is not important, but any high or low state on the timer clock input pins must be present for 2 oscillator cycles before it is guaranteed to be “seen” by the timer logic. All of the timer/counters (Timer 0, Timer 1 and Timer 2) can be independently programmed to operate either as timers or event counters via the C/T bit in the TnCON register. All timers count up unless otherwise stated. These timers may be dynamically read during program execution. Timer 0 and Timer 1 The “Timer” or “Counter” function is selected by control bits C/T in the special function register TMOD. These two Timer/Counters have four operating modes, which are selected by bit-pairs (M1, M0) in the TMOD register. Timer modes 1, 2, and 3 in XA are kept identical to the 80C51 timer modes for code compatibility. Only the mode 0 is replaced in the XA by a more powerful 16-bit auto-reload mode. This will give the XA timers a much larger range when used as time bases. The base clock rate of all of the timers is user programmable. This applies to timers T0, T1, and T2 when running in timer mode (as opposed to counter mode), and the watchdog timer. The clock driving the timers is called TCLK and is determined by the setting of two bits (PT1, PT0) in the System Configuration Register (SCR). The frequency of TCLK may be selected to be the oscillator input divided by 4 (Osc/4), the oscillator input divided by 16 (Osc/16), or the oscillator input divided by 64 (Osc/64). This gives a range of possibilities for the XA timer functions, including baud rate SCR Address:440 Not Bit Addressable Reset Value: 00H PT1 PT0 0 0 1 1 CM 0 1 0 1 PZ XA-G39 The recommended M1, M0 settings for the different modes are shown in Figure 6. MSB — LSB — — — PT1 PT0 CM PZ OPERATING Prescaler selection. Osc/4 Osc/16 Osc/64 Reserved Compatibility Mode allows the XA to execute most translated 80C51 code on the XA. The XA register file must copy the 80C51 mapping to data memory and mimic the 80C51 indirect addressing scheme. Page Zero mode forces all program and data addresses to 16-bits only. This saves stack space and speeds up execution but limits memory access to 64k. SU00589 Figure 5. System Configuration Register (SCR) TMOD Address:45C Not Bit Addressable Reset Value: 00H MSB GATE LSB C/T M1 M0 GATE TIMER 1 GATE C/T M1 0 0 1 1 M0 0 1 0 1 C/T M1 TIMER 0 Gating control when set. Timer/Counter “n” is enabled only while “INTn” pin is high and “TRn” control bit is set. When cleared Timer “n” is enabled whenever “TRn” control bit is set. Timer or Counter Selector cleared for Timer operation (input from internal system clock.) Set for Counter operation (input from “Tn” input pin). OPERATING 16-bit auto-reload timer/counter 16-bit non-auto-reload timer/counter 8-bit auto-reload timer/counter Dual 8-bit timer mode (timer 0 only) Figure 6. Timer/Counter Mode Control (TMOD) Register 2002 Mar 13 M0 19 SU00605 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs reloads TLn with the contents of RTLn, which is preset by software. The reload leaves THn unchanged. New Enhanced Mode 0 For timers T0 or T1 the 13-bit count mode on the 80C51 (current Mode 0) has been replaced in the XA with a 16-bit auto-reload mode. Four additional 8-bit data registers (two per timer: RTHn and RTLn) are created to hold the auto-reload values. In this mode, the TH overflow will set the TF flag in the TCON register and cause both the TL and TH counters to be loaded from the RTL and RTH registers respectively. Mode 2 operation is the same for Timer/Counter 0. The overflow rate for Timer 0 or Timer 1 in Mode 2 may be calculated as follows: Timer_Rate = Osc / (N * (256 – Timer_Reload_Value)) where N = the TCLK prescaler value: 4, 16, or 64. These new SFRs will also be used to hold the TL reload data in the 8-bit auto-reload mode (Mode 2) instead of TH. Mode 3 Timer 1 in Mode 3 simply holds its count. The effect is the same as setting TR1 = 0. The overflow rate for Timer 0 or Timer 1 in Mode 0 may be calculated as follows: Timer 0 in Mode 3 establishes TL0 and TH0 as two separate counters. TL0 uses the Timer 0 control bits C/T, GATE, TR0, and TF0 as well as pin INT0. TH0 is locked into a timer function and takes over the use of TR1 and TF1 from Timer 1. Thus, TH0 now controls the “Timer 1” interrupt. Timer_Rate = Osc / (N * (65536 – Timer_Reload_Value)) where N = the TCLK prescaler value: 4 (default), 16, or 64. Mode 1 Mode 1 is the 16-bit non-auto reload mode. Mode 3 is provided for applications requiring an extra 8-bit timer. When Timer 0 is in Mode 3, Timer 1 can be turned on and off by switching it out of and into its own Mode 3, or can still be used by the serial port as a baud rate generator, or in fact, in any application not requiring an interrupt. Mode 2 Mode 2 configures the Timer register as an 8-bit Counter (TLn) with automatic reload. Overflow from TLn not only sets TFn, but also TCON Address:410 Bit Addressable Reset Value: 00H BIT TCON.7 SYMBOL TF1 TCON.6 TCON.5 TR1 TF0 TCON.4 TCON.3 TR0 IE1 TCON.2 IT1 TCON.1 IE0 TCON.0 IT0 XA-G39 MSB TF1 LSB TR1 TF0 TR0 IE1 IT1 IE0 IT0 FUNCTION Timer 1 overflow flag. Set by hardware on Timer/Counter overflow. This flag will not be set if T1OE (TSTAT.2) is set. Cleared by hardware when processor vectors to interrupt routine, or by clearing the bit in software. Timer 1 Run control bit. Set/cleared by software to turn Timer/Counter 1 on/off. Timer 0 overflow flag. Set by hardware on Timer/Counter overflow. This flag will not be set if T0OE (TSTAT.0) is set. Cleared by hardware when processor vectors to interrupt routine, or by clearing the bit in software. Timer 0 Run control bit. Set/cleared by software to turn Timer/Counter 0 on/off. Interrupt 1 Edge flag. Set by hardware when external interrupt edge detected. Cleared when interrupt processed. Interrupt 1 type control bit. Set/cleared by software to specify falling edge/low level triggered external interrupts. Interrupt 0 Edge flag. Set by hardware when external interrupt edge detected. Cleared when interrupt processed. Interrupt 0 Type control bit. Set/cleared by software to specify falling edge/low level triggered external interrupts. SU00604C Figure 7. Timer/Counter Control (TCON) Register 2002 Mar 13 20 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs T2CON Address:418 Bit Addressable Reset Value: 00H BIT T2CON.7 T2CON.6 T2CON.5 T2CON.4 T2CON.3 T2CON.2 T2CON.1 T2CON.0 XA-G39 MSB TF2 LSB EXF2 RCLK0 TCLK0 EXEN2 TR2 C/T2 CP/RL2 SYMBOL FUNCTION TF2 Timer 2 overflow flag. Set by hardware on Timer/Counter overflow. Must be cleared by software. TF2 will not be set when RCLK0, RCLK1, TCLK0, TCLK1 or T2OE=1. EXF2 Timer 2 external flag is set when a capture or reload occurs due to a negative transition on T2EX (and EXEN2 is set). This flag will cause a Timer 2 interrupt when this interrupt is enabled. EXF2 is cleared by software. RCLK0 Receive Clock Flag. TCLK0 Transmit Clock Flag. RCLK0 and TCLK0 are used to select Timer 2 overflow rate as a clock source for UART0 instead of Timer T1. EXEN2 Timer 2 external enable bit allows a capture or reload to occur due to a negative transition on T2EX. TR2 Start=1/Stop=0 control for Timer 2. C/T2 Timer or counter select. 0=Internal timer 1=External event counter (falling edge triggered) CP/RL2 Capture/Reload flag. If CP/RL2 & EXEN2=1 captures will occur on negative transitions of T2EX. If CP/RL2=0, EXEN2=1 auto reloads occur with either Timer 2 overflows or negative transitions at T2EX. If RCLK or TCLK=1 the timer is set to auto reload on Timer 2 overflow, this bit has no effect. SU01592 Figure 8. Timer/Counter 2 Control (T2CON) Register Auto-Reload Mode (Up or Down Counter) In the auto-reload mode, the timer registers are loaded with the 16-bit value in T2CAPH and T2CAPL when the count overflows. T2CAPH and T2CAPL are initialized by software. If the EXEN2 bit in T2CON is set, the timer registers will also be reloaded and the EXF2 flag set when a 1-to-0 transition occurs at input T2EX. The auto-reload mode is shown in Figure 12. New Timer-Overflow Toggle Output In the XA, the timer module now has two outputs, which toggle on overflow from the individual timers. The same device pins that are used for the T0 and T1 count inputs are also used for the new overflow outputs. An SFR bit (TnOE in the TSTAT register) is associated with each counter and indicates whether Port-SFR data or the overflow signal is output to the pin. These outputs could be used in applications for generating variable duty cycle PWM outputs (changing the auto-reload register values). Also variable frequency (Osc/8 to Osc/8,388,608) outputs could be achieved by adjusting the prescaler along with the auto-reload register values. With a 30.0MHz oscillator, this range would be 3.58Hz to 3.75MHz. In this mode, Timer 2 can be configured to count up or down. This is done by setting or clearing the bit DCEN (Down Counter Enable) in the T2MOD special function register (see Table 4). The T2EX pin then controls the count direction. When T2EX is high, the count is in the up direction, when T2EX is low, the count is in the down direction. Timer T2 Timer 2 in the XA is a 16-bit Timer/Counter which can operate as either a timer or as an event counter. This is selected by C/T2 in the special function register T2CON. Upon timer T2 overflow/underflow, the TF2 flag is set, which may be used to generate an interrupt. It can be operated in one of three operating modes: auto-reload (up or down counting), capture, or as the baud rate generator (for either or both UARTs via SFRs T2MOD and T2CON). These modes are shown in Table 4. Figure 12 shows Timer 2, which will count up automatically, since DCEN = 0. In this mode there are two options selected by bit EXEN2 in the T2CON register. If EXEN2 = 0, then Timer 2 counts up to FFFFH and sets the TF2 (Overflow Flag) bit upon overflow. This causes the Timer 2 registers to be reloaded with the 16-bit value in T2CAPL and T2CAPH, whose values are preset by software. If EXEN2 = 1, a 16-bit reload can be triggered either by an overflow or by a 1-to-0 transition at input T2EX. This transition also sets the EXF2 bit. If enabled, either TF2 or EXF2 bit can generate the Timer 2 interrupt. Capture Mode In the capture mode there are two options which are selected by bit EXEN2 in T2CON. If EXEN2 = 0, then timer 2 is a 16-bit timer or counter, which upon overflowing sets bit TF2, the timer 2 overflow bit. This will cause an interrupt when the timer 2 interrupt is enabled. In Figure 13, the DCEN = 1; this enables the Timer 2 to count up or down. In this mode, the logic level of T2EX pin controls the direction of count. When a logic ‘1’ is applied at pin T2EX, the Timer 2 will count up. The Timer 2 will overflow at FFFFH and set the TF2 flag, which can then generate an interrupt if enabled. This timer overflow, also causes the 16-bit value in T2CAPL and T2CAPH to be reloaded into the timer registers TL2 and TH2, respectively. If EXEN2 = 1, then Timer 2 still does the above, but with the added feature that a 1-to-0 transition at external input T2EX causes the current value in the Timer 2 registers, TL2 and TH2, to be captured into registers RCAP2L and RCAP2H, respectively. In addition, the transition at T2EX causes bit EXF2 in T2CON to be set. This will cause an interrupt in the same fashion as TF2 when the Timer 2 interrupt is enabled. The capture mode is illustrated in Figure 11. 2002 Mar 13 A logic ‘0’ at pin T2EX causes Timer 2 to count down. When counting down, the timer value is compared to the 16-bit value contained in T2CAPH and T2CAPL. When the value is equal, the 21 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 timer register is loaded with FFFF hex. The underflow also sets the TF2 flag, which can generate an interrupt if enabled. Timer/Counter 2 or (2) to output a 50% duty cycle clock ranging from 3.58Hz to 3.75MHz at a 30MHz operating frequency. The external flag EXF2 toggles when Timer 2 underflows or overflows. This EXF2 bit can be used as a 17th bit of resolution, if needed. the EXF2 flag does not generate an interrupt in this mode. As the baud rate generator, timer T2 is incremented by TCLK. To configure the Timer/Counter 2 as a clock generator, bit C/T2 (in T2CON) must be cleared and bit T20E in T2MOD must be set. Bit TR2 (T2CON.2) also must be set to start the timer. The Clock-Out frequency depends on the oscillator frequency and the reload value of Timer 2 capture registers (TCAP2H, TCAP2L) as shown in this equation: Baud Rate Generator Mode By setting the TCLKn and/or RCLKn in T2CON or T2MOD, the Timer 2 can be chosen as the baud rate generator for either or both UARTs. The baud rates for transmit and receive can be simultaneously different. 2 TCLK (65536 * TCAP2H, TCAP2L) In the Clock-Out mode Timer 2 roll-overs will not generate an interrupt. This is similar to when it is used as a baud-rate generator. It is possible to use Timer 2 as a baud-rate generator and a clock generator simultaneously. Note, however, that the baud-rate will be 1/8 of the Clock-Out frequency. Programmable Clock-Out A 50% duty cycle clock can be programmed to come out on P1.6. This pin, besides being a regular I/O pin, has two alternate functions. It can be programmed (1) to input the external clock for Table 4. Timer 2 Operating Modes TR2 CP/RL2 RCLK+TCLK DCEN 0 X X X Timer off (stopped) 1 0 0 0 16-bit auto-reload, counting up 1 0 0 1 16-bit auto-reload, counting up or down depending on T2EX pin 1 1 0 X 16-bit capture 1 X 1 X Baud rate generator TSTAT Address:411 Bit Addressable Reset Value: 00H BIT TSTAT.2 SYMBOL T1OE TSTAT.0 T0OE MODE MSB — LSB — — — — T1OE — T0OE FUNCTION When 0, this bit allows the T1 pin to clock Timer 1 when in the counter mode. When 1, T1 acts as an output and toggles at every Timer 1 overflow. When 0, this bit allows the T0 pin to clock Timer 0 when in the counter mode. When 1, T0 acts as an output and toggles at every Timer 0 overflow. SU00612B Figure 9. Timer 0 And 1 Extended Status (TSTAT) T2MOD Address:419 Bit Addressable Reset Value: 00H MSB — LSB — RCLK1 TCLK1 — — T2OE DCEN BIT SYMBOL FUNCTION T2MOD.5 RCLK1 Receive Clock Flag. T2MOD.4 TCLK1 Transmit Clock Flag. RCLK1 and TCLK1 are used to select Timer 2 overflow rate as a clock source for UART1 instead of Timer T1. T2MOD.1 T2OE When 0, this bit allows the T2 pin to clock Timer 2 when in the counter mode. When 1, T2 acts as an output and toggles at every Timer 2 overflow. T2MOD.0 DCEN Controls count direction for Timer 2 in autoreload mode. DCEN=0 counter set to count up only DCEN=1 counter set to count up or down, depending on T2EX (see text). SU00610B Figure 10. Timer 2 Mode Control (T2MOD) 2002 Mar 13 22 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs TCLK XA-G39 C/T2 = 0 TL2 (8-bits) TH2 (8-bits) TF2 C/T2 = 1 T2 Pin Control Transition Detector TR2 Capture Timer 2 Interrupt T2CAPL T2CAPH T2EX Pin EXF2 Control EXEN2 SU00704 Figure 11. Timer 2 in Capture Mode TCLK C/T2 = 0 TL2 (8-bits) TH2 (8-bits) C/T2 = 1 T2 Pin Control TR2 Reload Transition Detector T2CAPL T2CAPH TF2 Timer 2 Interrupt T2EX Pin EXF2 Control EXEN2 SU00705 Figure 12. Timer 2 in Auto-Reload Mode (DCEN = 0) (DOWN COUNTING RELOAD VALUE) FFH FFH TOGGLE EXF2 TCLK C/T2 = 0 OVERFLOW TL2 T2 PIN TH2 TF2 INTERRUPT C/T2 = 1 CONTROL TR2 COUNT DIRECTION 1 = UP 0 = DOWN T2CAPL T2CAPH (UP COUNTING RELOAD VALUE) Figure 13. Timer 2 Auto Reload Mode (DCEN = 1) 2002 Mar 13 23 T2EX PIN SU00706 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs The software must be written so that a feed operation takes place every tD seconds from the last feed operation. Some tradeoffs may need to be made. It is not advisable to include feed operations in minor loops or in subroutines unless the feed operation is a specific subroutine. WATCHDOG TIMER The watchdog timer subsystem protects the system from incorrect code execution by causing a system reset when the watchdog timer underflows as a result of a failure of software to feed the timer prior to the timer reaching its terminal count. It is important to note that the watchdog timer is running after any type of reset and must be turned off by user software if the application does not use the watchdog function. To turn the watchdog timer completely off, the following code sequence should be used: mov.b mov.b mov.b Watchdog Function The watchdog consists of a programmable prescaler and the main timer. The prescaler derives its clock from the TCLK source that also drives timers 0, 1, and 2. The watchdog timer subsystem consists of a programmable 13-bit prescaler, and an 8-bit main timer. The main timer is clocked (decremented) by a tap taken from one of the top 8-bits of the prescaler as shown in Figure 14. The clock source for the prescaler is the same as TCLK (same as the clock source for the timers). Thus the main counter can be clocked as often as once every 32 TCLKs (see Table 5). The watchdog generates an underflow signal (and is autoloaded from WDL) when the watchdog is at count 0 and the clock to decrement the watchdog occurs. The watchdog is 8 bits wide and the autoload value can range from 0 to FFH. (The autoload value of 0 is permissible since the prescaler is cleared upon autoload). Watchdog Control Register (WDCON) The reset values of the WDCON and WDL registers will be such that the watchdog timer has a timeout period of 4 × 4096 × tOSC and the watchdog is running. WDCON can be written by software but the changes only take effect after executing a valid watchdog feed sequence. Table 5. Prescaler Select Values in WDCON tMIN = tOSC × 4 × 32 (W = 0, N = 4) tMAX = tOSC × 64 × 4096 × 256 (W = 255, N = 64) tD = tOSC × N × P × (W + 1) The watchdog timer is not directly loadable by the user. Instead, the value to be loaded into the main timer is held in an autoload register. In order to cause the main timer to be loaded with the appropriate value, a special sequence of software action must take place. This operation is referred to as feeding the watchdog timer. PRE1 PRE0 DIVISOR 0 0 0 32 0 0 1 64 0 1 0 128 0 1 1 256 1 0 0 512 1 0 1 1024 1 1 0 2048 1 1 1 4096 When external reset is applied, the following takes place: • Watchdog run control bit set to ON (1). • Autoload register WDL set to 00 (min. count). • Watchdog time-out flag cleared. • Prescaler is cleared. • Prescaler tap set to the highest divide. • Autoload takes place. ; disable global interrupts. ; do watchdog feed part 1 ; do watchdog feed part 2 ; re-enable global interrupts. When coming out of a hardware reset, the software should load the autoload register and then feed the watchdog (cause an autoload). This sequence assumes that the XA interrupt system is enabled and there is a possibility of an interrupt request occurring during the feed sequence. If an interrupt was allowed to be serviced and the service routine contained any SFR access, it would trigger a watchdog reset. If it is known that no interrupt could occur during the feed sequence, the instructions to disable and re-enable interrupts may be removed. 2002 Mar 13 PRE2 Watchdog Detailed Operation To feed the watchdog, two instructions must be sequentially executed successfully. No intervening SFR accesses are allowed, so interrupts should be disabled before feeding the watchdog. The instructions should move A5H to the WFEED1 register and then 5AH to the WFEED2 register. If WFEED1 is correctly loaded and WFEED2 is not correctly loaded, then an immediate watchdog reset will occur. The program sequence to feed the watchdog timer or cause new WDCON settings to take effect is as follows: ea wfeed1,#A5h wfeed2,#5Ah ea wdcon,#0 ; set WD control register to clear WDRUN. wfeed1,#A5h ; do watchdog feed part 1 wfeed2,#5Ah ; do watchdog feed part 2 This sequence assumes that the watchdog timer is being turned off at the beginning of initialization code and that the XA interrupt system has not yet been enabled. If the watchdog timer is to be turned off at a point when interrupts may be enabled, instructions to disable and re-enable interrupts should be added to this sequence. This leads to the following user design equations. Definitions: tOSC is the oscillator period, N is the selected prescaler tap value, W is the main counter autoload value, P is the prescaler value from Table 5, tMIN is the minimum watchdog time-out value (when the autoload value is 0), tMAX is the maximum time-out value (when the autoload value is FFH), tD is the design time-out value. clr mov.b mov.b setb XA-G39 If the watchdog is running and happens to underflow at the time the external reset is applied, the watchdog time-out flag will be cleared. 24 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 WDL WATCHDOG FEED SEQUENCE MOV WFEED1,#A5H MOV WFEED2,#5AH TCLK 8–BIT DOWN COUNTER PRESCALER PRE2 PRE1 PRE0 — — WDRUN INTERNAL RESET WDTOF — WDCON SU00581A Figure 14. Watchdog Timer in XA-G39 Each UART baud rate is determined by either a fixed division of the oscillator (in UART modes 0 and 2) or by the timer 1 or timer 2 overflow rate (in UART modes 1 and 3). When the watchdog underflows, the following action takes place (see Figure 14): • Autoload takes place. • Watchdog time-out flag is set • Watchdog run bit unchanged. • Autoload (WDL) register unchanged. • Prescaler tap unchanged. • All other device action same as external reset. Timer 1 defaults to clock both UART0 and UART1. Timer 2 can be programmed to clock either UART0 through T2CON (via bits R0CLK and T0CLK) or UART1 through T2MOD (via bits R1CLK and T1CLK). In this case, the UART not clocked by T2 could use T1 as the clock source. The serial port receive and transmit registers are both accessed at Special Function Register SnBUF. Writing to SnBUF loads the transmit register, and reading SnBUF accesses a physically separate receive register. Note that if the watchdog underflows, the program counter will be loaded from the reset vector as in the case of an internal reset. The watchdog time-out flag can be examined to determine if the watchdog has caused the reset condition. The watchdog time-out flag bit can be cleared by software. The serial port can operate in 4 modes: Mode 0: Serial I/O expansion mode. Serial data enters and exits through RxDn. TxDn outputs the shift clock. 8 bits are transmitted/received (LSB first). (The baud rate is fixed at 1/16 the oscillator frequency.) WDCON Register Bit Definitions WDCON.7 PRE2 Prescaler Select 2, reset to 1 WDCON.6 PRE1 Prescaler Select 1, reset to 1 WDCON.5 PRE0 Prescaler Select 0, reset to 1 WDCON.4 — WDCON.3 — WDCON.2 WDRUN Watchdog Run Control bit, reset to 1 WDCON.1 WDTOF Timeout flag WDCON.0 — Mode 1: Standard 8-bit UART mode. 10 bits are transmitted (through TxDn) or received (through RxDn): a start bit (0), 8 data bits (LSB first), and a stop bit (1). On receive, the stop bit goes into RB8 in Special Function Register SnCON. The baud rate is variable. Mode 2: Fixed rate 9-bit UART mode. 11 bits are transmitted (through TxD) or received (through RxD): start bit (0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). On Transmit, the 9th data bit (TB8_n in SnCON) can be assigned the value of 0 or 1. Or, for example, the parity bit (P, in the PSW) could be moved into TB8_n. On receive, the 9th data bit goes into RB8_n in Special Function Register SnCON, while the stop bit is ignored. The baud rate is programmable to 1/32 of the oscillator frequency. UARTs The XA-G39 includes 2 UART ports that are compatible with the enhanced UART used on the 8xC51Fx, 8xC51Rx+, 8xC51Rx2, and 8xC51Mx2. Baud rate selection is somewhat different due to the clocking scheme used for the XA timers. Mode 3: Standard 9-bit UART mode. 11 bits are transmitted (through TxDn) or received (through RxDn): a start bit (0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). In fact, Mode 3 is the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable. Some other enhancements have been made to UART operation. The first is that there are separate interrupt vectors for each UART’s transmit and receive functions. The UART transmitter has been double buffered, allowing packed transmission of data with no gaps between bytes and less critical interrupt service routine timing. A break detect function has been added to the UART. This operates independently of the UART itself and provides a start-of-break status bit that the program may test. Finally, an Overrun Error flag has been added to detect missed characters in the received data stream. The double buffered UART transmitter may require some software changes in code written for the original XA-G39 single buffered UART. 2002 Mar 13 In all four modes, transmission is initiated by any instruction that uses SnBUF as a destination register. Reception is initiated in Mode 0 by the condition RI_n = 0 and REN_n = 1. Reception is initiated in the other modes by the incoming start bit if REN_n = 1. 25 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs message has been transmitted completely. The interrupt service routine should handle this additional interrupt. Serial Port Control Register The serial port control and status register is the Special Function Register SnCON, shown in Figure 16. This register contains not only the mode selection bits, but also the 9th data bit for transmit and receive (TB8_n and RB8_n), and the serial port interrupt bits (TI_n and RI_n). The recommended method of using the double buffering in the application program is to have the interrupt service routine handle a single byte for each interrupt occurrence. In this manner the program essentially does not require any special considerations for double buffering. Unless higher priority interrupts cause delays in the servicing of the UART transmitter interrupt, the double buffering will result in transmitted bytes being tightly packed with no intervening gaps. TI Flag In order to allow easy use of the double buffered UART transmitter feature, the TI_n flag is set by the UART hardware under two conditions. The first condition is the completion of any byte transmission. This occurs at the end of the stop bit in modes 1, 2, or 3, or at the end of the eighth data bit in mode 0. The second condition is when SnBUF is written while the UART transmitter is idle. In this case, the TI_n flag is set in order to indicate that the second UART transmitter buffer is still available. 9-bit Mode Please note that the ninth data bit (TB8) is not double buffered. Care must be taken to insure that the TB8 bit contains the intended data at the point where it is transmitted. Double buffering of the UART transmitter may be bypassed as a simple means of synchronizing TB8 to the rest of the data stream. Typically, UART transmitters generate one interrupt per byte transmitted. In the case of the XA UART, one additional interrupt is generated as defined by the stated conditions for setting the TI_n flag. This additional interrupt does not occur if double buffering is bypassed as explained below. Note that if a character oriented approach is used to transmit data through the UART, there could be a second interrupt for each character transmitted, depending on the timing of the writes to SBUF. For this reason, it is generally better to bypass double buffering when the UART transmitter is used in character oriented mode. This is also true if the UART is polled rather than interrupt driven, and when transmission is character oriented rather than message or string oriented. The interrupt occurs at the end of the last byte transmitted when the UART becomes idle. Among other things, this allows a program to determine when a 2002 Mar 13 XA-G39 Bypassing Double Buffering The UART transmitter may be used as if it is single buffered. The recommended UART transmitter interrupt service routine (ISR) technique to bypass double buffering first clears the TI_n flag upon entry into the ISR, as in standard practice. This clears the interrupt that activated the ISR. Secondly, the TI_n flag is cleared immediately following each write to SnBUF. This clears the interrupt flag that would otherwise direct the program to write to the second transmitter buffer. If there is any possibility that a higher priority interrupt might become active between the write to SnBUF and the clearing of the TI_n flag, the interrupt system may have to be temporarily disabled during that sequence by clearing, then setting the EA bit in the IEL register. 26 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 CLOCKING SCHEME/BAUD RATE GENERATION Using Timer 2 to Generate Baud Rates The XA UARTS clock rates are determined by either a fixed division (modes 0 and 2) of the oscillator clock or by the Timer 1 or Timer 2 overflow rate (modes 1 and 3). Timer T2 is a 16-bit up/down counter in XA. As a baud rate generator, timer 2 is selected as a clock source for either/both UART0 and UART1 transmitters and/or receivers by setting TCLKn and/or RCLKn in T2CON and T2MOD. As the baud rate generator, T2 is incremented as Osc/N where N = 4, 16 or 64 depending on TCLK as programmed in the SCR bits PT1, and PTO. So, if T2 is the source of one UART, the other UART could be clocked by either T1 overflow or fixed clock, and the UARTs could run independently with different baud rates. The clock for the UARTs in XA runs at 16x the Baud rate. If the timers are used as the source for Baud Clock, since maximum speed of timers/Baud Clock is Osc/4, the maximum baud rate is timer overflow divided by 16 i.e. Osc/64. In Mode 0, it is fixed at Osc/16. In Mode 2, however, the fixed rate is Osc/32. Pre-scaler f allll Ti for Timers T0 T0,1,2 12 controlled by PT1, PT0 bits in SCR 00 Osc/4 01 Osc/16 10 Osc/64 11 reserved T2CON 0x418 T2MOD 0x419 Baud Rate for UART Mode 0: Baud_Rate = Osc/16 bit5 bit4 RCLK0 TCLK0 bit5 bit4 RCLK1 TCLK1 Prescaler Select for Timer Clock (TCLK) Baud Rate calculation for UART Mode 1 and 3: Baud_Rate = Timer_Rate/16 SCR 0x440 bit3 bit2 PT1 PT0 Timer_Rate = Osc/(N*(Timer_Range– Timer_Reload_Value)) where N = the TCLK prescaler value: 4, 16, or 64. and Timer_Range = 256 for timer 1 in mode 2. 65536 for timer 1 in mode 0 and timer 2 in count up mode. The timer reload value may be calculated as follows: Timer_Reload_Value = Timer_Range–(Osc/(Baud_Rate*N*16)) NOTES: 1. The maximum baud rate for a UART in mode 1 or 3 is Osc/64. 2. The lowest possible baud rate (for a given oscillator frequency and N value) may be found by using a timer reload value of 0. 3. The timer reload value may never be larger than the timer range. 4. If a timer reload value calculation gives a negative or fractional result, the baud rate requested is not possible at the given oscillator frequency and N value. Baud Rate for UART Mode 2: Baud_Rate = Osc/32 SnSTAT Address: S0STAT 421 S1STAT 425 Bit Addressable Reset Value: 00H MSB — LSB — — — FEn BRn OEn STINTn BIT SYMBOL FUNCTION SnSTAT.3 FEn Framing Error flag is set when the receiver fails to see a valid STOP bit at the end of the frame. Cleared by software. SnSTAT.2 BRn Break Detect flag is set if a character is received with all bits (including STOP bit) being logic ‘0’. Thus it gives a “Start of Break Detect” on bit 8 for Mode 1 and bit 9 for Modes 2 and 3. The break detect feature operates independently of the UARTs and provides the START of Break Detect status bit that a user program may poll. Cleared by software. SnSTAT.1 OEn Overrun Error flag is set if a new character is received in the receiver buffer while it is still full (before the software has read the previous character from the buffer), i.e., when bit 8 of a new byte is received while RI in SnCON is still set. Cleared by software. SnSTAT.0 STINTn This flag must be set to enable any of the above status flags to generate a receive interrupt (RIn). The only way it can be cleared is by a software write to this register. SU00607B Figure 15. Serial Port Extended Status (SnSTAT) Register (See also Figure 17 regarding Framing Error flag) 2002 Mar 13 27 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 A0H – A3H UART 0 Receiver 7 A4H – A7H UART 0 Transmitter 8 Given slave address or addresses. All of the slaves may be contacted by using the Broadcast address. Two special Function Registers are used to define the slave’s address, SADDR, and the address mask, SADEN. SADEN is used to define which bits in the SADDR are to be used and which bits are “don’t care”. The SADEN mask can be logically ANDed with the SADDR to create the “Given” address which the master will use for addressing each of the slaves. Use of the Given address allows multiple slaves to be recognized while excluding others. The following examples will help to show the versatility of this scheme: A8H – ABH UART 1 Receiver 9 Slave 0 ACH – AFH UART 1 Transmitter 10 SADDR = SADEN = Given = 1100 0000 1111 1101 1100 00X0 Slave 1 SADDR = SADEN = Given = 1100 0000 1111 1110 1100 000X UART INTERRUPT SCHEME There are separate interrupt vectors for each UART’s transmit and receive functions. Table 6. Vector Locations for UARTs in XA Vector Address Interrupt Source Arbitration NOTE: The transmit and receive vectors could contain the same ISR address to work like a 8051 interrupt scheme Error Handling, Status Flags and Break Detect The UARTs in XA has the following error flags; see Figure 15. In the above example SADDR is the same and the SADEN data is used to differentiate between the two slaves. Slave 0 requires a 0 in bit 0 and it ignores bit 1. Slave 1 requires a 0 in bit 1 and bit 0 is ignored. A unique address for Slave 0 would be 1100 0010 since slave 1 requires a 0 in bit 1. A unique address for slave 1 would be 1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be selected at the same time by an address which has bit 0 = 0 (for slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed with 1100 0000. Multiprocessor Communications Modes 2 and 3 have a special provision for multiprocessor communications. In these modes, 9 data bits are received. The 9th one goes into RB8. Then comes a stop bit. The port can be programmed such that when the stop bit is received, the serial port interrupt will be activated only if RB8 = 1. This feature is enabled by setting bit SM2 in SCON. A way to use this feature in multiprocessor systems is as follows: In a more complex system the following could be used to select slaves 1 and 2 while excluding slave 0: When the master processor wants to transmit a block of data to one of several slaves, it first sends out an address byte which identifies the target slave. An address byte differs from a data byte in that the 9th bit is 1 in an address byte and 0 in a data byte. With SM2 = 1, no slave will be interrupted by a data byte. An address byte, however, will interrupt all slaves, so that each slave can examine the received byte and see if it is being addressed. The addressed slave will clear its SM2 bit and prepare to receive the data bytes that will be coming. The slaves that weren’t being addressed leave their SM2s set and go on about their business, ignoring the coming data bytes. SM2 has no effect in Mode 0, and in Mode 1 can be used to check the validity of the stop bit although this is better done with the Framing Error (FE) flag. In a Mode 1 reception, if SM2 = 1, the receive interrupt will not be activated unless a valid stop bit is received. SADDR = SADEN = Given = 1100 0000 1111 1001 1100 0XX0 Slave 1 SADDR = SADEN = Given = 1110 0000 1111 1010 1110 0X0X Slave 2 SADDR = SADEN = Given = 1110 0000 1111 1100 1110 00XX In the above example the differentiation among the 3 slaves is in the lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be uniquely addressed by 1110 0110. Slave 1 requires that bit 1 = 0 and it can be uniquely addressed by 1110 and 0101. Slave 2 requires that bit 2 = 0 and its unique address is 1110 0011. To select Slaves 0 and 1 and exclude Slave 2 use address 1110 0100, since it is necessary to make bit 2 = 1 to exclude slave 2. Automatic Address Recognition Automatic Address Recognition is a feature which allows the UART to recognize certain addresses in the serial bit stream by using hardware to make the comparisons. This feature saves a great deal of software overhead by eliminating the need for the software to examine every serial address which passes by the serial port. This feature is enabled by setting the SM2 bit in SCON. In the 9 bit UART modes, mode 2 and mode 3, the Receive Interrupt flag (RI) will be automatically set when the received byte contains either the “Given” address or the “Broadcast” address. The 9 bit mode requires that the 9th information bit is a 1 to indicate that the received information is an address and not data. Automatic address recognition is shown in Figure 18. The Broadcast Address for each slave is created by taking the logical OR of SADDR and SADEN. Zeros in this result are teated as don’t-cares. In most cases, interpreting the don’t-cares as ones, the broadcast address will be FF hexadecimal. Upon reset SADDR and SADEN are loaded with 0s. This produces a given address of all “don’t cares” as well as a Broadcast address of all “don’t cares”. This effectively disables the Automatic Addressing mode and allows the microcontroller to use standard UART drivers which do not make use of this feature. Using the Automatic Address Recognition feature allows a master to selectively communicate with one or more slaves by invoking the 2002 Mar 13 Slave 0 28 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs SnCON Address: S0CON 420 S1CON 424 XA-G39 MSB LSB SM0 Bit Addressable Reset Value: 00H SM1 SM2 REN TB8 RB8 TI RI Where SM0, SM1 specify the serial port mode, as follows: SM0 0 0 1 1 SM1 0 1 0 1 Mode 0 1 2 3 Description shift register 8-bit UART 9-bit UART 9-bit UART Baud Rate fOSC/16 variable fOSC/32 variable BIT SYMBOL FUNCTION SnCON.5 SM2 Enables the multiprocessor communication feature in Modes 2 and 3. In Mode 2 or 3, if SM2 is set to 1, then RI will not be activated if the received 9th data bit (RB8) is 0. In Mode 1, if SM2=1 then RI will not be activated if a valid stop bit was not received. In Mode 0, SM2 should be 0. SnCON.4 REN Enables serial reception. Set by software to enable reception. Clear by software to disable reception. SnCON.3 TB8 The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired. The TB8 bit is not double buffered. See text for details. SnCON.2 RB8 In Modes 2 and 3, is the 9th data bit that was received. In Mode 1, if SM2=0, RB8 is the stop bit that was received. In Mode 0, RB8 is not used. SnCON.1 TI Transmit interrupt flag. Set when another byte may be written to the UART transmitter. See text for details. Must be cleared by software. SnCON.0 RI Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the end of the stop bit time in the other modes (except see SM2). Must be cleared by software. SU00597C Figure 16. Serial Port Control (SnCON) Register D0 D1 D2 D3 D4 D5 D6 D7 D8 DATA BYTE START BIT ONLY IN MODE 2, 3 STOP BIT if 0, sets FE — — — — FEn BRn OEn STINTn SnSTAT SU00598 Figure 17. UART Framing Error Detection D0 D1 D2 D3 SM0_n 1 1 D4 SM1_n D5 D6 SM2_n REN_n TB8_n 1 X 1 1 0 D7 D8 RB8_n TI_n RI_n SnCON RECEIVED ADDRESS D0 TO D7 COMPARATOR PROGRAMMED ADDRESS IN UART MODE 2 OR MODE 3 AND SM2 = 1: INTERRUPT IF REN=1, RB8=1 AND “RECEIVED ADDRESS” = “PROGRAMMED ADDRESS” – WHEN OWN ADDRESS RECEIVED, CLEAR SM2 TO RECEIVE DATA BYTES – WHEN ALL DATA BYTES HAVE BEEN RECEIVED: SET SM2 TO WAIT FOR NEXT ADDRESS. SU00613 Figure 18. UART Multiprocessor Communication, Automatic Address Recognition 2002 Mar 13 29 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 the address contained in the memory location 0000h. The destination of the reset jump must be located in the first 64 K of code address on power-up, all vectors are 16-bit values and so point to page zero addresses only. After a reset the RAM contents are indeterminate. I/O PORT OUTPUT CONFIGURATION Each I/O port pin can be user configured to one of 4 output types. The types are Quasi-bidirectional (essentially the same as standard 80C51 family I/O ports), Open-Drain, Push-Pull, and Off (high impedance). The default configuration after reset is Quasi-bidirectional. However, in the ROMless mode (the EA pin is low at reset), the port pins that comprise the external data bus will default to push-pull outputs. Alternatively, the Boot Vector may supply the reset address. This happens when use of the Boot Vector is forced or when the Flash status byte is non-zero. These cases are described in the section “Hardware Activation of the Boot Vector” on page 11. I/O port output configurations are determined by the settings in port configuration SFRs. There are 2 SFRs for each port, called PnCFGA and PnCFGB, where “n” is the port number. One bit in each of the 2 SFRs relates to the output setting for the corresponding port pin, allowing any combination of the 2 output types to be mixed on those port pins. For instance, the output type of port 1 pin 3 is controlled by the setting of bit 3 in the SFRs P1CFGA and P1CFGB. VDD R XA RST C Table 7 shows the configuration register settings for the 4 port output types. The electrical characteristics of each output type may be found in the DC Characteristic table. SOME TYPICAL VALUES FOR R AND C: R = 100K, C = 1.0 µF R = 1.0M, C = 0.1 µF (ASSUMING THAT THE VDD RISE TIME IS 1ms OR LESS) Table 7. Port Configuration Register Settings PnCFGB PnCFGA 0 0 Open Drain 0 1 Quasi-bidirectional 1 0 Off (high impedance) 1 1 Push-Pull Figure 19. Recommended Reset Circuit Port Output Mode RESET OPTIONS The EA pin is sampled on the rising edge of the RST pulse, and determines whether the device is to begin execution from internal or external code memory. EA pulled high configures the XA in single-chip mode. If EA is driven low, the device enters ROMless mode. After Reset is released, the EA/WAIT pin becomes a bus wait signal for external bus transactions. NOTE: Mode changes may cause glitches to occur during transitions. When modifying both registers, WRITE instructions should be carried out consecutively. The BUSW/P3.5 pin is weakly pulled high while reset is asserted, allowing simple biasing of the pin with a resistor to ground to select the alternate bus width. If the BUSW pin is not driven at reset, the weak pullup will cause a 1 to be loaded for the bus width, giving a 16-bit external bus. BUSW may be pulled low with a 2.7 K or smaller value resistor, giving an 8-bit external bus. The bus width setting from the BUSW pin may be overridden by software once the user program is running. EXTERNAL BUS The external program/data bus allows for 8-bit or 16-bit bus width, and address sizes from 12 to 20 bits. The bus width is selected by an input at reset (see Reset Options below), while the address size is set by the program in a configuration register. If all off-chip code is selected (through the use of the EA pin), the initial code fetches will be done with the maximum address size (20 bits). Both EA and BUSW must be held for three oscillator clock times after reset is deasserted to guarantee that their values are latched correctly. RESET The device is reset whenever a logic “0“ is applied to RST for at least 10 microseconds, placing a low level on the pin re-initializes the on-chip logic. Reset must be asserted when power is initially applied to the XA and held until the oscillator is running. POWER REDUCTION MODES The XA-G39 supports Idle and Power Down modes of power reduction. The idle mode leaves some peripherals running to allow them to wake up the processor when an interrupt is generated. The power down mode stops the oscillator in order to minimize power. The processor can be made to exit power down mode via reset or one of the external interrupt inputs. In order to use an external interrupt to re-activate the XA while in power down mode, the external interrupt must be enabled and be configured to level sensitive mode. In power down mode, the power supply voltage may be reduced to the RAM keep-alive voltage (2 V), retaining the RAM, register, and SFR values at the point where the power down mode was entered. The duration of reset must be extended when power is initially applied or when using reset to exit power down mode. This is due to the need to allow the oscillator time to start up and stabilize. For most power supply ramp up conditions, this time is 10 milliseconds. To provide a reliable reset during momentary power supply interruption or whenever the power supply voltage drops below the specified operating voltage, it is recommended that a CMOS system reset circuit SA56614-XX or similar device be used, see application note AN468. As RST is brought high again, an exception is generated which causes the processor to jump to the reset address. Typically, this is 2002 Mar 13 SU00702 30 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 The XA-G39 supports a total of 9 maskable event interrupt sources (for the various XA peripherals), seven software interrupts, 5 exception interrupts (plus reset), and 16 traps. The maskable event interrupts share a global interrupt disable bit (the EA bit in the IEL register) and each also has a separate individual interrupt enable bit (in the IEL or IEH registers). Only three bits of the IPA register values are used on the XA-G39. Each event interrupt can be set to occur at one of 8 priority levels via bits in the Interrupt Priority (IP) registers, IPA0 through IPA5. The value 0 in the IPA field gives the interrupt priority 0, in effect disabling the interrupt. A value of 1 gives the interrupt a priority of 9, the value 2 gives priority 10, etc. The result is the same as if all four bits were used and the top bit set for all values except 0. Details of the priority scheme may be found in the XA User Guide. INTERRUPTS The XA-G39 supports 38 vectored interrupt sources. These include 9 maskable event interrupts, 7 exception interrupts, 16 trap interrupts, and 7 software interrupts. The maskable interrupts each have 8 priority levels and may be globally and/or individually enabled or disabled. The XA defines four types of interrupts: • Exception Interrupts – These are system level errors and other very important occurrences which include stack overflow, divide-by-0, and reset. • Event interrupts – These are peripheral interrupts from devices such as UARTs, timers, and external interrupt inputs. • Software Interrupts – These are equivalent of hardware The complete interrupt vector list for the XA-G39, including all 4 interrupt types, is shown in the following tables. The tables include the address of the vector for each interrupt, the related priority register bits (if any), and the arbitration ranking for that interrupt source. The arbitration ranking determines the order in which interrupts are processed if more than one interrupt of the same priority occurs simultaneously. interrupt, but are requested only under software control. • Trap Interrupts – These are TRAP instructions, generally used to call system services in a multi-tasking system. Exception interrupts, software interrupts, and trap interrupts are generally standard for XA derivatives and are detailed in the XA User Guide. Event interrupts tend to be different on different XA derivatives. Table 8. Interrupt Vectors EXCEPTION/TRAPS PRECEDENCE VECTOR ADDRESS ARBITRATION RANKING Reset (h/w, watchdog, s/w) DESCRIPTION 0000–0003 0 (High) Breakpoint (h/w trap 1) 0004–0007 1 Trace (h/w trap 2) 0008–000B 1 Stack Overflow (h/w trap 3) 000C–000F 1 Divide by 0 (h/w trap 4) 0010–0013 1 User RETI (h/w trap 5) 0014–0017 1 TRAP 0– 15 (software) 0040–007F 1 EVENT INTERRUPTS FLAG BIT VECTOR ADDRESS ENABLE BIT INTERRUPT PRIORITY ARBITRATION RANKING External interrupt 0 IE0 0080–0083 EX0 IPA0.2–0 (PX0) 2 Timer 0 interrupt TF0 0084–0087 ET0 IPA0.6–4 (PT0) 3 DESCRIPTION External interrupt 1 IE1 0088–008B EX1 IPA1.2–0 (PX1) 4 Timer 1 interrupt TF1 008C–008F ET1 IPA1.6–4 (PT1) 5 Timer 2 interrupt TF2(EXF2) 0090–0093 ET2 IPA2.2–0 (PT2) 6 Serial port 0 Rx RI.0 00A0–00A3 ERI0 IPA4.2–0 (PRIO) 7 Serial port 0 Tx TI.0 00A4–00A7 ETI0 IPA4.6–4 (PTIO) 8 Serial port 1 Rx RI.1 00A8–00AB ERI1 IPA5.2–0 (PRT1) 9 Serial port 1 Tx TI.1 00AC–00AF ETI1 IPA5.6–4 (PTI1) 10 FLAG BIT VECTOR ADDRESS ENABLE BIT INTERRUPT PRIORITY Software interrupt 1 SWR1 0100–0103 SWE1 (fixed at 1) Software interrupt 2 SWR2 0104–0107 SWE2 (fixed at 2) Software interrupt 3 SWR3 0108–010B SWE3 (fixed at 3) Software interrupt 4 SWR4 010C–010F SWE4 (fixed at 4) Software interrupt 5 SWR5 0110–0113 SWE5 (fixed at 5) Software interrupt 6 SWR6 0114–0117 SWE6 (fixed at 6) Software interrupt 7 SWR7 0118–011B SWE7 (fixed at 7) SOFTWARE INTERRUPTS DESCRIPTION 2002 Mar 13 31 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNIT Operating temperature under bias –55 to +125 °C Storage temperature range –65 to +150 °C 0 to +13.0 V Voltage on EA/VPP pin to VSS Voltage on any other pin to VSS –0.5 to VDD+0.5 V V Maximum IOL per I/O pin 15 mA Power dissipation (based on package heat transfer limitations, not device power consumption) 1.5 W DC ELECTRICAL CHARACTERISTICS VDD = 4.5 V to 5.5 V; Tamb = 0 to +70 °C, unless otherwise specified. VDD = 4.75 V to 5.25 V; Tamb = –40 to +85 °C, unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS LIMITS MIN TYP MAX UNIT Supplies IDD Supply current operating 5.25 V, 30 MHz 110 mA IID Idle mode supply current 5.25 V, 30 MHz 40 mA IPD Power-down current 30 mA IPDI Power-down current (–40 °C to +85 °C) 150 mA VRAM RAM-keep-alive voltage VIL Input low voltage VIH Input high voltage, except XTAL1, RST At 5.0 V 2.2 VIH1 Input high voltage to XTAL1, RST At 5.0 V 0.8VDD VIL1 Input low voltage to XATL1, RST At 5.0 V VOL Output low voltage all ports, ALE, PSEN3 IOL = 3.2mA, VDD = 5.0 V VOH1 Output high voltage all ports, ALE, PSEN1 IOH = –100mA, VDD = VDDmin 2.4 V VOH2 Output high voltage, ports P0–3, ALE, PSEN2 IOH = 3.2mA, VDD = VDDmin 2.4 V CIO Input/Output pin capacitance IIL Logical 0 input current, P0–36 VIN = 0.45 V ILI Input leakage current, P0–35 ITL Logical 1 to 0 transition current all ports4 RAM-keep-alive voltage 1.5 V –0.5 0.22 VDD V V V 0.12 VDD 0.5 V 15 pF –75 mA VIN = VIL or VIH ±10 mA At 5.25 V –650 mA –25 NOTES: 1. Ports in Quasi bi-directional mode with weak pull-up (applies to ALE, PSEN only during RESET). 2. Ports in Push-Pull mode, both pull-up and pull-down assumed to be same strength 3. In all output modes 4. Port pins source a transition current when used in quasi-bidirectional mode and externally driven from 1 to 0. This current is highest when VIN is approximately 2 V. 5. Measured with port in high impedance output mode. 6. Measured with port in quasi-bidirectional output mode. 7. Load capacitance for all outputs=80pF. 8. Under steady state (non-transient) conditions, IOL must be externally limited as follows: 15mA (*NOTE: This is 85 °C specification for VDD = 5 V.) Maximum IOL per port pin: Maximum IOL per 8-bit port: 26mA Maximum total IOL for all output: 71mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 2002 Mar 13 32 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 AC ELECTRICAL CHARACTERISTICS (5 V) VDD = 4.5 V to 5.5 V; Tamb = 0 to +70 °C for commercial; VDD = 4.75 V to 5.25 V, –40 °C to +85 °C for industrial. VARIABLE CLOCK SYMBOL FIGURE PARAMETER MIN MAX 0 30 UNIT External Clock fC tC Oscillator frequency 26 Clock period and CPU timing cycle 1/fC MHz ns 7 tCHCX 26 Clock high time tC * 0.5 tCLCX 26 Clock low time tC * 0.4 7 ns tCLCH 26 Clock rise time 5 ns tCHCL 26 Clock fall time 5 ns tCRAR 25 Delay from clock rising edge to ALE rising edge 46 ns tLHLL 20 ALE pulse width (programmable) (V1 * tC) – 6 ns tAVLL 20 Address valid to ALE de-asserted (set-up) (V1 * tC) – 14 ns tLLAX 20 Address hold after ALE de-asserted (tC/2) – 10 ns (V2 * tC) – 10 ns ns Address Cycle 5 Code Read Cycle tPLPH 20 PSEN pulse width tLLPL 20 ALE de-asserted to PSEN asserted tAVIVA 20 Address valid to instruction valid, ALE cycle (access time) (V3 * tC) – 36 ns tAVIVB 21 Address valid to instruction valid, non-ALE cycle (access time) (V4 * tC) – 29 ns tPLIV 20 PSEN asserted to instruction valid (enable time) (V2 * tC) – 29 ns tPXIX 20 Instruction hold after PSEN de-asserted tPXIZ 20 Bus 3-State after PSEN de-asserted (disable time) tIXUA 20 Hold time of unlatched part of address after instruction latched tRLRH 22 RD pulse width tLLRL 22 ALE de-asserted to RD asserted tAVDVA 22 Address valid to data input valid, ALE cycle (access time) (V6 * tC) – 36 ns tAVDVB 23 Address valid to data input valid, non-ALE cycle (access time) (V5 * tC) – 29 ns tRLDV 22 RD low to valid data in, enable time (V7 * tC) – 29 ns tRHDX 22 Data hold time after RD de-asserted tRHDZ 22 Bus 3-State after RD de-asserted (disable time) tDXUA 22 Hold time of unlatched part of address after data latched tWLWH 24 tLLWL 24 tQVWX (tC/2) – 7 ns 0 ns tC – 8 ns 0 ns (V7 * tC) – 10 ns Data Read Cycle (tC/2) – 7 ns 0 ns tC – 8 ns 0 ns WR pulse width (V8 * tC) – 10 ns ALE falling edge to WR asserted (V12 * tC) – 10 ns 24 Data valid before WR asserted (data setup time) (V13 * tC) – 22 ns tWHQX 24 Data hold time after WR de-asserted (Note 6) (V11 * tC) – 7 ns tAVWL 24 Address valid to WR asserted (address setup time) (Note 5) (V9 * tC) – 22 ns tUAWH 24 Hold time of unlatched part of address after WR is de-asserted (V11 * tC) – 7 ns tWTH 25 WAIT stable after bus strobe (RD, WR, or PSEN) asserted tWTL 25 WAIT hold after bus strobe (RD, WR, or PSEN) assertion Data Write Cycle Wait Input (V10 * tC) – 30 (V10 * tC) – 5 NOTES: 1. Load capacitance for all outputs = 80pF. 2. Variables V1 through V13 reflect programmable bus timing, which is programmed via the Bus Timing registers (BTRH and BTRL). Refer to the XA User Guide for details of the bus timing settings. V1) This variable represents the programmed width of the ALE pulse as determined by the ALEW bit in the BTRL register. V1 = 0.5 if the ALEW bit = 0, and 1.5 if the ALEW bit = 1. 2002 Mar 13 33 ns ns Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 This variable represents the programmed width of the PSEN pulse as determined by the CR1 and CR0 bits or the CRA1, CRA0, and ALEW bits in the BTRL register. – For a bus cycle with no ALE, V2 = 1 if CR1/0 = 00, 2 if CR1/0 = 01, 3 if CR1/0 = 10, and 4 if CR1/0 = 11. Note that during burst mode code fetches, PSEN does not exhibit transitions at the boundaries of bus cycles. V2 still applies for the purpose of determining peripheral timing requirements. – For a bus cycle with an ALE, V2 = the total bus cycle duration (2 if CRA1/0 = 00, 3 if CRA1/0 = 01, 4 if CRA1/0 = 10, and 5 if CRA1/0 = 11) minus the number of clocks used by ALE (V1 + 0.5). Example: If CRA1/0 = 10 and ALEW = 1, the V2 = 4 – (1.5 + 0.5) = 2. V3) This variable represents the programmed length of an entire code read cycle with ALE. This time is determined by the CRA1 and CRA0 bits in the BTRL register. V3 = the total bus cycle duration (2 if CRA1/0 = 00, 3 if CRA1/0 = 01, 4 if CRA1/0 = 10, and 5 if CRA1/0 = 11). V4) This variable represents the programmed length of an entire code read cycle with no ALE. This time is determined by the CR1 and CR0 bits in the BTRL register. V4 = 1 if CR1/0 = 00, 2 if CR1/0 = 01, 3 if CR1/0 = 10, and 4 if CR1/0 = 11. V5) This variable represents the programmed length of an entire data read cycle with no ALE. this time is determined by the DR1 and DR0 bits in the BTRH register. V5 = 1 if DR1/0 = 00, 2 if DR1/0 = 01, 3 if DR1/0 = 10, and 4 if DR1/0 = 11. V6) This variable represents the programmed length of an entire data read cycle with ALE. The time is determined by the DRA1 and DRA0 bits in the BTRH register. V6 = the total bus cycle duration (2 if DRA1/0 = 00, 3 if DRA1/0 = 01, 4 if DRA1/0 = 10, and 5 if DRA1/0 = 11). V7) This variable represents the programmed width of the RD pulse as determined by the DR1 and DR0 bits or the DRA1, DRA0 in the BTRH register, and the ALEW bit in the BTRL register. Note that during a 16-bit operation on an 8-bit external bus, RD remains low and does not exhibit a transition between the first and second byte bus cycles. V7 still applies for the purpose of determining peripheral timing requirements. The timing for the first byte is for a bus cycle with ALE, the timing for the second byte is for a bus cycle with no ALE. – For a bus cycle with no ALE, V7 = 1 if DR1/0 = 00, 2 if DR1/0 = 01, 3 if DR1/0 = 10, and 4 if DR1/0 = 11. – For a bus cycle with an ALE, V7 = the total bus cycle duration (2 if DRA1/0 = 00, 3 if DRA1/0 = 01, 4 if DRA1/0 = 10, and 5 if DRA1/0 = 11) minus the number of clocks used by ALE (V1 + 0.5). Example: If DRA1/0 = 00 and ALEW = 0, then V7 = 2 – (0.5 + 0.5) = 1. V8) This variable represents the programmed width of the WRL and/or WRH pulse as determined by the WM1 bit in the BTRL register. V8 1 if WM1 = 0, and 2 if WM1 = 1. V9) This variable represents the programmed address setup time for a write as determined by the data write cycle duration (defined by DW1 and DW0 or the DWA1 and DWA0 bits in the BTRH register), the WM0 bit in the BTRL register, and the value of V8. – For a bus cycle with an ALE, V9 = the total bus write cycle duration (2 if DWA1/0 = 00, 3 if DWA1/0 = 01, 4 if DWA1/0 = 10, and 5 if DWA1/0 = 11) minus the number of clocks used by the WRL and/or WRH pulse (V8), minus the number of clocks used by data hold time (0 if WM0 = 0 and 1 if WM0 = 1). Example: If DWA1/0 = 10, WM0 = 1, and WM1 = 1, then V9 = 4 – 1 – 2 = 1. – For a bus cycle with no ALE, V9 = the total bus cycle duration (2 if DW1/0 = 00, 3 if DW1/0 = 01, 4 if DW1/0 = 10, and 5 if DW1/0 = 11) minus the number of clocks used by the WRL and/or WRH pulse (V8), minus the number of clocks used by data hold time (0 if WM0 = 0 and 1 if WM0 = 1). Example: If DW1/0 = 11, WM0 = 1, and WM1 = 0, then V9 = 5 – 1 – 1 = 3. V10) This variable represents the length of a bus strobe for calculation of WAIT setup and hold times. The strobe may be RD (for data read cycles), WRL and/or WRH (for data write cycles), or PSEN (for code read cycles), depending on the type of bus cycle being widened by WAIT. V10 = V2 for WAIT associated with a code read cycle using PSEN. V10 = V8 for a data write cycle using WRL and/or WRH. V10 = V7–1 for a data read cycle using RD. This means that a single clock data read cycle cannot be stretched using WAIT. If WAIT is used to vary the duration of data read cycles, the RD strobe width must be set to be at least two clocks in duration. Also see Note 4. V11) This variable represents the programmed write hold time as determined by the WM0 bit in the BTRL register. V11 = 0 if the WM0 bit = 0, and 1 if the WM0 bit = 1. V12) This variable represents the programmed period between the end of the ALE pulse and the beginning of the WRL and/or WRH pulse as determined by the data write cycle duration (defined by the DWA1 and DWA0 bits in the BTRH register), the WM0 bit in the BTRL register, and the values of V1 and V8. V12 = the total bus cycle duration (2 if DWA1/0 = 00, 3 if DWA1/0 = 01, 4 if DWA1/0 = 10, and 5 if DWA1/0 = 11) minus the number of clocks used by the WRL and/or WRH pulse (V8), minus the number of clocks used by data hold time (0 if WM0 = 0 and 1 if WM0 = 1), minus the width of the ALE pulse (V1). Example: If DWA1/0 = 11, WM0 = 1, WM1 = 0, and ALEW = 1, then V12 = 5 – 1 – 1 – 1.5 = 1.5. V13) This variable represents the programmed data setup time for a write as determined by the data write cycle duration (defined by DW1 and DW0 or the DWA1 and DWA0 bits in the BTRH register), the WM0 bit in the BTRL register, and the values of V1 and V8. – For a bus cycle with an ALE, V13 = the total bus cycle duration (2 if DWA1/0 = 00, 3 if DWA1/0 = 01, 4 if DWA1/0 = 10, and 5 if DWA1/0 = 11) minus the number of clocks used by the WRL and/or WRH pulse (V8), minus the number of clocks used by data hold time (0 if WM0 = 0 and 1 if WM0 = 1), minus the number of clocks used by ALE (V1 + 0.5). Example: If DWA1/0 = 11, WM0 = 1, WM1 = 1, and ALEW = 0, then V13 = 5 – 1 – 2 – 1 = 1. – For a bus cycle with no ALE, V13 = the total bus cycle duration (2 if DW1/0 = 00, 3 if DW1/0 = 01, 4 if DW1/0 = 10, and 5 if DW1/0 = 11) minus the number of clocks used by the WRL and/or WRH pulse (V8), minus the number of clocks used by data hold time (0 if WM0 = 0 and 1 if WM0 = 1). Example: If DW1/0 = 01, WM0 = 1, and WM1 = 0, then V13 = 3 – 1 – 1 = 1. 3. Not all combinations of bus timing configuration values result in valid bus cycles. Please refer to the XA User Guide section on the External Bus for details. 4. When code is being fetched for execution on the external bus, a burst mode fetch is used that does not have PSEN edges in every fetch cycle. Thus, if WAIT is used to delay code fetch cycles, a change in the low order address lines must be detected to locate the beginning of a cycle. This would be A3–A0 for an 8-bit bus, and A3–A1 for a 16-bit bus. Also, a 16-bit data read operation conducted on a 8-bit wide bus similarly does not include two separate RD strobes. So, a rising edge on the low order address line (A0) must be used to trigger a WAIT in the second half of such a cycle. V2) 2002 Mar 13 34 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 5. This parameter is provided for peripherals that have the data clocked in on the falling edge of the WR strobe. This is not usually the case, and in most applications this parameter is not used. 6. Please note that the XA-G39 requires that extended data bus hold time (WM0 = 1) to be used with external bus write cycles. 7. Applies only to an external clock source, not when a crystal or ceramic resonator is connected to the XTAL1 and XTAL2 pins. tLHLL ALE tAVLL tLLPL tPLPH tPLIV PSEN tLLAX tPXIZ tPXIX MULTIPLEXED ADDRESS AND DATA A4–A11 or A4–A19 INSTR IN * tIXUA tAVIVA UNMULTIPLEXED ADDRESS * A0 or A1–A3, A12–19 INSTR IN is either D0–D7 or D0–D15, depending on the bus width (8 or 16 bits). SU01073 Figure 20. External Program Memory Read Cycle (ALE Cycle) ALE PSEN MULTIPLEXED ADDRESS AND DATA A4–A11 or A4–A19 INSTR IN * tAVIVB UNMULTIPLEXED ADDRESS * A0 or A1–A3, A12–19 A0 or A1–A3, A12–19 INSTR IN is either D0–D7 or D0–D15, depending on the bus width (8 or 16 bits). Figure 21. External Program Memory Read Cycle (Non-ALE Cycle) 2002 Mar 13 35 SU00707 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 ALE tLLRL RD tAVLL tRLRH tLLAX tRHDZ tRLDV tRHDX MULTIPLEXED ADDRESS AND DATA A4–A11 or A4–A19 DATA IN * tDXUA tAVDVA UNMULTIPLEXED ADDRESS * A0 or A1–A3, A12–A19 DATA IN is either D0–D7 or D0–D15, depending on the bus width (8 or 16 bits). SU00947 Figure 22. External Data Memory Read Cycle (ALE Cycle) ALE RD MULTIPLEXED ADDRESS AND DATA D0–D7 A4–A11 DATA IN * tAVDVB UNMULTIPLEXED ADDRESS A0–A3, A12–A19 A0–A3, A12–A19 SU00708A Figure 23. External Data Memory Read Cycle (Non-ALE Cycle) 2002 Mar 13 36 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 ALE tWLWH tLLWL WRL or WRH tLLAX tAVLL MULTIPLEXED ADDRESS AND DATA tQVWX tWHQX DATA OUT * A4–A11 or A4–A15 tAVWL tUAWH UNMULTIPLEXED ADDRESS * A0 or A1–A3, A12–A19 DATA OUT is either D0–D7 or D0–D15, depending on the bus width (8 or 16 bits). SU00584C Figure 24. External Data Memory Write Cycle XTAL1 tCRAR ALE ADDRESS BUS WAIT BUS STROBE (WRL, WRH, RD, OR PSEN) tWTH (The dashed line shows the strobe without WAIT.) tWTL SU00709A Figure 25. WAIT Signal Timing 2002 Mar 13 37 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs VDD–0.5 XA-G39 0.7VDD 0.2VDD–0.1 0.45V tCHCL tCHCX tCLCH tCLCX tC SU00842 Figure 26. External Clock Drive VDD–0.5 0.2VDD+0.9 0.2VDD–0.1 0.45V NOTE: AC inputs during testing are driven at VDD –0.5 for a logic ‘1’ and 0.45V for a logic ‘0’. Timing measurements are made at the 50% point of transitions. SU00703A Figure 27. AC Testing Input/Output VLOAD+0.1V VOH–0.1V TIMING REFERENCE POINTS VLOAD VLOAD–0.1V VOL+0.1V NOTE: For timing purposes, a port is no longer floating when a 100mV change from load voltage occurs, and begins to float when a 100mV change from the loaded VOH/VOL level occurs. IOH/IOL ≥ ±20mA. SU00011 Figure 28. Float Waveform VDD VDD VDD VDD RST VDD RST EA EA (NC) XTAL2 (NC) XTAL2 CLOCK SIGNAL XTAL1 CLOCK SIGNAL XTAL1 VSS VSS SU00591B SU00590B Figure 29. IDD Test Condition, Active Mode All other pins are disconnected 2002 Mar 13 Figure 30. IDD Test Condition, Idle Mode All other pins are disconnected 38 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 120 MAX. IDD (ACTIVE) 100 80 60 CURRENT (mA) 40 MAX. IDD (IDLE) 20 0 0 5 15 10 25 20 30 FREQUENCY (MHz) SU00844 Figure 31. IDD vs. Frequency Valid only within frequency specification of the device under test. VDD–0.5 0.7VDD 0.2VDD–0.1 0.45V tCHCL tCHCX tCLCH tCLCX tCL SU00608A Figure 32. Clock Signal Waveform for IDD Tests in Active and Idle Modes tCLCH = tCHCL = 5ns VDD VDD VDD RST EA (NC) XTAL2 XTAL1 VSS SU00585A Figure 33. IDD Test Condition, Power Down Mode All other pins are disconnected. VDD=2 V to 5.5 V 2002 Mar 13 39 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs PLCC44: plastic leaded chip carrier; 44 leads 2002 Mar 13 XA-G39 SOT187-2 40 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs REVISION HISTORY Date CPCN Description 2002 Mar 13 9397 750 08927 Initial release 2002 Mar 13 41 XA-G39 Philips Semiconductors Preliminary data XA 16-bit microcontroller family 32K Flash/1K RAM, watchdog, 2 UARTs XA-G39 Data sheet status Data sheet status [1] Product status [2] Definitions Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Koninklijke Philips Electronics N.V. 2002 All rights reserved. Printed in U.S.A. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Date of release: 03-02 For sales offices addresses send e-mail to: [email protected]. Document order number: 2002 Mar 13 42 9397 750 08927