INTEGRATED CIRCUITS 74ALS11A Triple 3-Input AND gate Product specification IC05 Data Handbook 1991 Feb 08 Philips Semiconductors Product specification Triple 3-input AND gate TYPE 74ALS11A TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 5.5ns 1.3mA 74ALS11A PIN CONFIGURATION ORDERING INFORMATION ORDER CODE COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C DRAWING NUMBER 14-pin plastic DIP 74ALS11AN SOT27-1 14-pin plastic SO 74ALS11AD SOT108-1 DESCRIPTION 1A 1 14 VCC 1B 2 13 1C 2A 3 12 1Y 2B 4 11 3C 2C 5 10 3B 2Y 6 9 3A GND 7 8 3Y SC00019 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74ALS (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW nA, nB, nC Data inputs 1.0/1.0 20µA/0.1mA nY Data output 20/80 0.4mA/8mA NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state. LOGIC SYMBOL IEC/IEEE SYMBOL 1 1 2 13 3 4 5 9 10 11 & 2 12 13 3 1A 1B 1C 2A 2B 2C 3A 3B 3C 4 6 5 1Y 2Y 3Y 9 10 12 6 VCC = Pin 14 GND = Pin 7 SC00020 SC00021 LOGIC DIAGRAM 1A 1B 1C 2A 2B 2C 3A 3B VCC = Pin 14 GND = Pin 7 1991 Feb 08 8 11 8 3C FUNCTION TABLE 1 2 INPUTS 12 13 3 4 6 5 9 10 11 8 1Y 2Y 3Y OUTPUT nA nB nB nY H H H H L X X L X L X L X X L H H = High voltage level L = Low voltage level X = Don’t care SC00022 2 853–0304 01670 Philips Semiconductors Product specification Triple 3-input AND gate 74ALS11A ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) PARAMETER SYMBOL RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA –0.5 to VCC V VOUT Voltage applied to output in High output state IOUT Current applied to output in Low output state Tamb Operating free-air temperature range Tstg Storage temperature range 16 mA 0 to +70 °C –65 to +150 °C RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER UNIT MIN NOM MAX 5.0 5.5 VCC Supply voltage 4.5 VIH High-level input voltage 2.0 VIL Low-level input voltage 0.8 V IIk Input clamp current –18 mA IOH High-level output current –0.4 mA IOL Low-level output current 8 mA +70 °C Tamb Operating free-air temperature range V V 0 DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL LIMITS TEST CONDITIONS1 PARAMETER MIN VOH High-level output voltage VCC±10%, VIL = MAX, VIH = MIN, IOH = –0.4mA VOL O Low level output voltage Low-level VCC = MIN,, VIL = MAX,, VIH = MIN VIK Input clamp voltage VCC = MIN, II = IIK II Input current at maximum input voltage IIH TYP2 UNIT MAX VCC – 2 V IOL = 4mA 0.25 0.40 V IOL = 8mA 0.35 0.50 V -0.73 -1.5 V VCC = MAX, VI = 7.0V 0.1 mA High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V -0.1 mA IO current3 ICC Output Supply current (total) VCC = MAX, VO = 2.25V ICCH ICCL VCC = MAX -112 mA VI = 4.5V -30 1.0 1.8 mA VI = 0V 2.0 3.0 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. The output conditions have been chosen to produce a current that closely approximate one half of the true short-circuit output current, IOS. 1991 Feb 08 3 Philips Semiconductors Product specification Triple 3-input AND gate 74ALS11A AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER tPLH tPHL Tamb = 0°C to +70°C VCC = +5.0V ± 10% CL = 50pF, RL = 500Ω TEST CONDITION Propagation delay nA, nB, nC to nY Waveform 1 MIN MAX 2.0 2.0 11.0 10.0 UNIT ns AC WAVEFORMS For all waveforms, VM = 1.3V. nA, nB, nC VM VM tPLH tPHL VM nY VM SC00023 Waveform 1. Propagation Delay for Data to Output TEST CIRCUIT AND WAVEFORMS VCC NEGATIVE PULSE VIN CL RL AMP (V) VM 10% D.U.T. RT 90% VM VOUT PULSE GENERATOR tw 90% 10% tTHL (tff) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0.3V AMP (V) 90% Test Circuit for Totem-pole Outputs POSITIVE PULSE 90% VM VM 10% 10% tw 0.3V Input Pulse Definition DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. INPUT PULSE REQUIREMENTS Family Amplitude VM 74ALS 3.5V 1.3V Rep.Rate tw tTLH tTHL 1MHz 500ns 2.0ns 2.0ns SC00005 1991 Feb 08 4 Philips Semiconductors Product specification Triple 3-input AND gate 74ALS11A DIP14: plastic dual in-line package; 14 leads (300 mil) 1991 Feb 08 5 SOT27-1 Philips Semiconductors Product specification Triple 3-input AND gate 74ALS11A SO14: plastic small outline package; 14 leads; body width 3.9 mm 1991 Feb 08 6 SOT108-1 Philips Semiconductors Product specification Triple 3-input AND gate 1991 Feb 08 74ALS11A 7