74AUP1G885 Low-power dual function gate Rev. 05 — 26 June 2009 Product data sheet 1. General description The 74AUP1G885 provides two functions in one device. The output state of the outputs (1Y, 2Y) is determined by the inputs (A, B and C). The output 1Y provides the Boolean function: 1Y = A × C. The output 2Y provides the Boolean function: 2Y = A × B + A × C. Schmitt-trigger action at all inputs makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V. This device ensures a very low static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V. This device is fully specified for partial power-down applications using IOFF. The IOFF circuitry disables the output, preventing a damaging backflow current through the device when it is powered down. 2. Features n Wide supply voltage range from 0.8 V to 3.6 V n High noise immunity n Complies with JEDEC standards: u JESD8-12 (0.8 V to 1.3 V) u JESD8-11 (0.9 V to 1.65 V) u JESD8-7 (1.2 V to 1.95 V) u JESD8-5 (1.8 V to 2.7 V) u JESD8-B (2.7 V to 3.6 V) n ESD protection: u HBM JESD22-A114E Class 3A exceeds 5000 V u MM JESD22-A115-A exceeds 200 V u CDM JESD22-C101C exceeds 1000 V n Low static power consumption; ICC = 0.9 µA (maximum) n Latch-up performance exceeds 100 mA per JESD78 Class II n Inputs accept voltages up to 3.6 V n Low noise overshoot and undershoot < 10 % of VCC n IOFF circuitry provides partial Power-down mode operation n Multiple package options n Specified from −40 °C to +85 °C and −40 °C to +125 °C 74AUP1G885 NXP Semiconductors Low-power dual function gate 3. Ordering information Table 1. Ordering information Type number Package Temperature range Name Description Version 74AUP1G885DC −40 °C to +125 °C VSSOP8 plastic very thin shrink small outline package; 8 leads; SOT765-1 body width 2.3 mm 74AUP1G885GT −40 °C to +125 °C XSON8 plastic extremely thin small outline package; no leads; SOT833-1 8 terminals; body 1 × 1.95 × 0.5 mm 74AUP1G885GD −40 °C to +125 °C XSON8U plastic extremely thin small outline package; no leads; SOT996-2 8 terminals; UTLP based; body 3 × 2 × 0.5 mm 74AUP1G885GM −40 °C to +125 °C XQFN8U plastic extremely thin quad flat package; no leads; 8 terminals; UTLP based; body 1.6 × 1.6 × 0.5 mm SOT902-1 4. Marking Table 2. Marking codes Type number Marking code[1] 74AUP1G885DC pS8 74AUP1G885GT pS8 74AUP1G885GD pS8 74AUP1G885GM pS8 [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. 5. Functional diagram A 2Y B C Fig 1. 1Y 001aah898 Logic diagram 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 2 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate 6. Pinning information 6.1 Pinning 74AUP1G885 A 1 8 VCC B 2 7 1Y 2Y 3 6 C GND 4 5 n.c. 74AUP1G885 A 1 8 VCC B 2 7 1Y 2Y 3 6 C GND 4 5 n.c. 001aae355 Transparent top view 001aae354 Fig 2. Pin configuration SOT765-1 (VSSOP8) Fig 3. Pin configuration SOT833-1 (XSON8) 74AUP1G885 74AUP1G885 1 8 VCC B 2 7 1Y 2Y 3 6 C GND 4 5 n.c. 1 C n.c. 8 1Y 7 A 2 6 B 3 5 2Y GND 4 A VCC terminal 1 index area 001aaj897 Transparent top view Fig 4. 001aaf630 Transparent top view Pin configuration SOT996-2 (XSON8U) Fig 5. Pin configuration SOT902-1 (XQFN8U) 6.2 Pin description Table 3. Symbol Pin description Pin Description SOT765-1, SOT833-1 and SOT996-2 SOT902-1 1, 2, 6 7, 6, 2 data input GND 4 4 ground (0 V) n.c. 5 3 not connected 1Y, 2Y 7, 3 1, 5 data output VCC 8 8 supply voltage A, B, C 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 3 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate 7. Functional description Table 4. Function table[1] Input Output A B C 1Y 2Y L L L L L H L L L H L H L L H H H L L H L L H L L H L H H L L H H L H H H H H L [1] H = HIGH voltage level; L = LOW voltage level. 8. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter VCC supply voltage IIK input clamping current VI input voltage IOK output clamping current Conditions Min −0.5 +4.6 V VI < 0 V −50 - mA −0.5 +4.6 V −50 - mA −0.5 +4.6 V - ±20 mA [1] VO < 0 V [1] Max Unit VO output voltage Active mode and Power-down mode IO output current VO = 0 V to VCC ICC supply current - 50 mA IGND ground current −50 - mA Tstg storage temperature −65 +150 °C Ptot total power dissipation - 250 mW Tamb = −40 °C to +125 °C [2] [1] The minimum input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For VSSOP8 packages: above 110 °C the value of Ptot derates linearly with 8.0 mW/K. For XSON8, XSON8U and XQFN8U packages: above 118 °C the value of Ptot derates linearly with 7.8 mW/K. 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 4 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate 9. Recommended operating conditions Table 6. Operating conditions Symbol Parameter VCC Conditions Min Max Unit supply voltage 0.8 3.6 V VI input voltage 0 3.6 V VO output voltage Tamb ambient temperature ∆t/∆V input transition rise and fall rate Active mode 0 VCC V Power-down mode; VCC = 0 V 0 3.6 V −40 +125 °C - 200 ns/V VCC = 0.8 V to 3.6 V 10. Static characteristics Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min VCC = 0.8 V Typ Max Unit 0.70 × VCC - - V VCC = 0.9 V to 1.95 V 0.65 × VCC - - V VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V VCC = 0.8 V - - 0.30 × VCC V VCC = 0.9 V to 1.95 V - - 0.35 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V IO = −20 µA; VCC = 0.8 V to 3.6 V VCC − 0.1 - - V IO = −1.1 mA; VCC = 1.1 V 0.75 × VCC - - V IO = −1.7 mA; VCC = 1.4 V 1.11 - - V IO = −1.9 mA; VCC = 1.65 V 1.32 - - V IO = −2.3 mA; VCC = 2.3 V 2.05 - - V IO = −3.1 mA; VCC = 2.3 V 1.9 - - V IO = −2.7 mA; VCC = 3.0 V 2.72 - - V IO = −4.0 mA; VCC = 3.0 V 2.6 - - V Tamb = 25 °C VIH VIL VOH HIGH-level input voltage LOW-level input voltage HIGH-level output voltage VI = VIH or VIL 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 5 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions VOL VI = VIH or VIL LOW-level output voltage II input leakage current Min Typ Max Unit IO = 20 µA; VCC = 0.8 V to 3.6 V - - 0.1 V IO = 1.1 mA; VCC = 1.1 V - - 0.3 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.31 V IO = 1.9 mA; VCC = 1.65 V - - 0.31 V IO = 2.3 mA; VCC = 2.3 V - - 0.31 V IO = 3.1 mA; VCC = 2.3 V - - 0.44 V IO = 2.7 mA; VCC = 3.0 V - - 0.31 V IO = 4.0 mA; VCC = 3.0 V - - 0.44 V VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.1 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.2 µA ∆IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - ±0.2 µA ICC supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 0.5 µA ∆ICC additional supply current VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V - - 40 µA CI input capacitance VCC = 0 V to 3.6 V; VI = GND or VCC - 0.6 - pF CO output capacitance VO = GND; VCC = 0 V - 1.3 - pF VCC = 0.8 V 0.70 × VCC - - V VCC = 0.9 V to 1.95 V 0.65 × VCC - - V [1] Tamb = −40 °C to +85 °C VIH VIL VOH HIGH-level input voltage LOW-level input voltage HIGH-level output voltage VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V VCC = 0.8 V - - 0.30 × VCC V VCC = 0.9 V to 1.95 V - - 0.35 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V IO = −20 µA; VCC = 0.8 V to 3.6 V VCC − 0.1 - - V VI = VIH or VIL IO = −1.1 mA; VCC = 1.1 V 0.7 × VCC - - V IO = −1.7 mA; VCC = 1.4 V 1.03 - - V IO = −1.9 mA; VCC = 1.65 V 1.30 - - V IO = −2.3 mA; VCC = 2.3 V 1.97 - - V IO = −3.1 mA; VCC = 2.3 V 1.85 - - V IO = −2.7 mA; VCC = 3.0 V 2.67 - - V IO = −4.0 mA; VCC = 3.0 V 2.55 - - V 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 6 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions VOL VI = VIH or VIL LOW-level output voltage II input leakage current Min Typ Max Unit IO = 20 µA; VCC = 0.8 V to 3.6 V - - 0.1 V IO = 1.1 mA; VCC = 1.1 V - - 0.3 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.37 V IO = 1.9 mA; VCC = 1.65 V - - 0.35 V IO = 2.3 mA; VCC = 2.3 V - - 0.33 V IO = 3.1 mA; VCC = 2.3 V - - 0.45 V IO = 2.7 mA; VCC = 3.0 V - - 0.33 V IO = 4.0 mA; VCC = 3.0 V - - 0.45 V VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.5 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.5 µA ∆IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - ±0.6 µA ICC supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 0.9 µA ∆ICC additional supply current VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V - - 50 µA [1] Tamb = −40 °C to +125 °C VIH VIL VOH HIGH-level input voltage LOW-level input voltage HIGH-level output voltage VCC = 0.8 V 0.75 × VCC - - V VCC = 0.9 V to 1.95 V 0.70 × VCC - - V VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V VCC = 0.8 V - - 0.25 × VCC V VCC = 0.9 V to 1.95 V - - 0.30 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V VI = VIH or VIL IO = −20 µA; VCC = 0.8 V to 3.6 V VCC − 0.11 - - V IO = −1.1 mA; VCC = 1.1 V 0.6 × VCC - - V IO = −1.7 mA; VCC = 1.4 V 0.93 - - V IO = −1.9 mA; VCC = 1.65 V 1.17 - - V IO = −2.3 mA; VCC = 2.3 V 1.77 - - V IO = −3.1 mA; VCC = 2.3 V 1.67 - - V IO = −2.7 mA; VCC = 3.0 V 2.40 - - V IO = −4.0 mA; VCC = 3.0 V 2.30 - - V 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 7 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions VOL VI = VIH or VIL LOW-level output voltage II input leakage current Min Typ Max Unit IO = 20 µA; VCC = 0.8 V to 3.6 V - - 0.11 V IO = 1.1 mA; VCC = 1.1 V - - 0.33 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.41 V IO = 1.9 mA; VCC = 1.65 V - - 0.39 V IO = 2.3 mA; VCC = 2.3 V - - 0.36 V IO = 3.1 mA; VCC = 2.3 V - - 0.50 V IO = 2.7 mA; VCC = 3.0 V - - 0.36 V IO = 4.0 mA; VCC = 3.0 V - - 0.50 V VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.75 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.75 µA ∆IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - ±0.75 µA ICC supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 1.4 µA ∆ICC additional supply current VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V - - 75 µA [1] [1] One input at VCC − 0.6 V, other inputs at VCC or GND. 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 8 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate 11. Dynamic characteristics Table 8. Dynamic characteristics Voltages are referenced to GND (ground = 0 V; for test circuit see Figure 7. Symbol Parameter 25 °C Conditions −40 °C to +125 °C Unit Min Typ[1] Max Min Max Max (85 °C) (125 °C) VCC = 0.8 V - 17.3 - - - - ns VCC = 1.1 V to 1.3 V 1.1 5.2 9.7 0.9 12.8 14.2 ns VCC = 1.4 V to 1.6 V 1.2 3.7 5.9 1.0 7.8 8.6 ns VCC = 1.65 V to 1.95 V 1.1 3.0 4.8 0.9 6.2 6.9 ns VCC = 2.3 V to 2.7 V 1.1 2.4 3.6 1.0 4.1 4.5 ns 1.1 2.1 3.1 1.0 3.6 4.1 ns VCC = 0.8 V - 21.5 - - - - ns VCC = 1.1 V to 1.3 V 1.7 6.0 12.7 1.4 12.8 14.2 ns VCC = 1.4 V to 1.6 V 1.7 4.2 7.2 1.4 7.8 8.7 ns VCC = 1.65 V to 1.95 V 1.4 3.3 5.8 1.2 6.5 7.2 ns VCC = 2.3 V to 2.7 V 1.2 2.6 4.1 1.0 4.7 5.2 ns VCC = 3.0 V to 3.6 V 1.1 2.3 3.5 0.9 3.8 4.2 ns VCC = 0.8 V - 20.8 - - - - ns VCC = 1.1 V to 1.3 V 1.2 6.1 11.4 1.2 14.6 16.1 ns VCC = 1.4 V to 1.6 V 1.4 4.3 7.2 1.2 8.7 9.6 ns VCC = 1.65 V to 1.95 V 1.4 3.6 5.7 1.3 6.8 7.5 ns VCC = 2.3 V to 2.7 V 1.4 2.9 4.2 1.2 4.8 5.4 ns 1.4 2.7 3.9 1.3 4.1 4.6 ns VCC = 0.8 V - 25.0 - - - - ns VCC = 1.1 V to 1.3 V 1.8 6.9 14.4 1.7 14.6 16.1 ns VCC = 1.4 V to 1.6 V 1.9 4.8 8.5 1.5 9.1 10.1 ns VCC = 1.65 V to 1.95 V 1.9 3.9 6.6 1.7 7.2 8.0 ns VCC = 2.3 V to 2.7 V 1.5 3.1 4.7 1.3 5.4 5.9 ns VCC = 3.0 V to 3.6 V 1.4 2.8 4.3 1.3 4.6 5.1 ns CL = 5 pF tpd propagation delay A, C to 1Y; see Figure 6 [2] VCC = 3.0 V to 3.6 V A, B to 2Y; see Figure 6 [2] CL = 10 pF tpd propagation delay A, C to 1Y; see Figure 6 [2] VCC = 3.0 V to 3.6 V A, B to 2Y; see Figure 6 [2] 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 9 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate Table 8. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V; for test circuit see Figure 7. Symbol Parameter 25 °C Conditions −40 °C to +125 °C Unit Min Typ[1] Max Min Max Max (85 °C) (125 °C) VCC = 0.8 V - 24.3 - - - - ns VCC = 1.1 V to 1.3 V 1.3 6.9 13.0 1.2 16.2 17.9 ns VCC = 1.4 V to 1.6 V 1.7 4.9 8.0 1.4 9.7 10.8 ns VCC = 1.65 V to 1.95 V 1.5 4.1 6.4 1.4 7.6 8.4 ns VCC = 2.3 V to 2.7 V 1.7 3.4 5.0 1.6 5.4 6.0 ns 1.7 3.1 4.4 1.6 4.7 5.3 ns VCC = 0.8 V - 28.5 - - - - ns VCC = 1.1 V to 1.3 V 2.1 7.7 16.0 1.9 16.3 18.0 ns VCC = 1.4 V to 1.6 V 2.2 5.4 9.4 2.4 10.3 11.4 ns VCC = 1.65 V to 1.95 V 2.0 4.4 7.4 1.8 8.2 9.1 ns VCC = 2.3 V to 2.7 V 1.8 3.6 5.5 1.6 6.0 6.7 ns VCC = 3.0 V to 3.6 V 1.7 3.3 4.8 1.5 5.2 5.8 ns VCC = 0.8 V - 34.7 - - - - ns VCC = 1.1 V to 1.3 V 2.4 9.2 17.7 2.3 20.9 23.0 ns VCC = 1.4 V to 1.6 V 2.5 6.5 10.6 2.5 12.2 13.5 ns VCC = 1.65 V to 1.95 V 2.5 5.4 8.5 2.4 9.4 10.4 ns VCC = 2.3 V to 2.7 V 2.6 4.5 6.4 2.4 7.0 7.7 ns 2.5 4.2 5.7 2.3 6.6 7.3 ns CL = 15 pF tpd propagation delay A, C to 1Y; see Figure 6 [2] VCC = 3.0 V to 3.6 V A, B to 2Y; see Figure 6 [2] CL = 30 pF tpd propagation delay A, C to 1Y; see Figure 6 [2] VCC = 3.0 V to 3.6 V A, B to 2Y; see Figure 6 [2] VCC = 0.8 V - 38.9 - - - - ns VCC = 1.1 V to 1.3 V 2.6 10.0 20.5 2.6 21.5 23.7 ns VCC = 1.4 V to 1.6 V 2.6 6.9 11.9 2.6 13.2 14.5 ns VCC = 1.65 V to 1.95 V 2.7 5.7 9.5 2.7 10.5 11.6 ns VCC = 2.3 V to 2.7 V 2.5 4.7 6.9 2.5 7.6 8.4 ns VCC = 3.0 V to 3.6 V 2.4 4.4 6.1 2.4 7.1 7.9 ns 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 10 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate Table 8. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V; for test circuit see Figure 7. Symbol Parameter 25 °C Conditions −40 °C to +125 °C Unit Min Typ[1] Max Min Max Max (85 °C) (125 °C) VCC = 0.8 V - 2.7 - - - - pF VCC = 1.1 V to 1.3 V - 2.9 - - - - pF CL = 5 pF, 10 pF, 15 pF and 30 pF power dissipation capacitance CPD fi = 1 MHz; VI = GND to VCC [3][4] VCC = 1.4 V to 1.6 V - 3.0 - - - - pF VCC = 1.65 V to 1.95 V - 3.1 - - - - pF VCC = 2.3 V to 2.7 V - 3.5 - - - - pF VCC = 3.0 V to 3.6 V - 4.1 - - - - pF [1] All typical values are measured at nominal VCC. [2] tpd is the same as tPLH and tPHL. [3] All specified values are the average typical values over all stated loads. [4] CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; Σ(CL × VCC2 × fo) = sum of the outputs. 12. Waveforms VI VM A, B, C input GND t PHL t PLH VOH VM nY output 001aae356 VOL Measurement points are given in Table 9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Fig 6. Table 9. The data input (A, B, C) to output (nY) propagation delays Measurement points Supply voltage Output Input VCC VM VM VI tr = tf 0.8 V to 3.6 V 0.5 × VCC 0.5 × VCC VCC ≤ 3.0 ns 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 11 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate VCC VEXT 5 kΩ G VI VO DUT RT CL RL 001aac521 Test data is given in Table 10. Definitions for test circuit: RL = Load resistance. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to the output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Fig 7. Table 10. Load circuitry for switching times Test data Supply voltage Load VEXT VCC CL RL[1] 0.8 V to 3.6 V 5 pF, 10 pF, 15 pF and 30 pF 5 kΩ or 1 MΩ [1] tPLH, tPHL tPZH, tPHZ tPZL, tPLZ open GND 2 × VCC For measuring enable and disable times RL = 5 kΩ. For measuring propagation delays, set-up and hold times and pulse width RL = 1 MΩ. 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 12 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate 13. Package outline VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm D E SOT765-1 A X c y HE v M A Z 5 8 Q A A2 A1 pin 1 index (A3) θ Lp 1 4 e L detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(2) e HE L Lp Q v w y Z(1) θ mm 1 0.15 0.00 0.85 0.60 0.12 0.27 0.17 0.23 0.08 2.1 1.9 2.4 2.2 0.5 3.2 3.0 0.4 0.40 0.15 0.21 0.19 0.2 0.13 0.1 0.4 0.1 8° 0° Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT765-1 Fig 8. REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 02-06-07 MO-187 Package outline SOT765-1 (VSSOP8) 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 13 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm 1 2 SOT833-1 b 4 3 4× (2) L L1 e 8 7 6 e1 5 e1 e1 8× A (2) A1 D E terminal 1 index area 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A(1) max A1 max b D E e e1 L L1 mm 0.5 0.04 0.25 0.17 2.0 1.9 1.05 0.95 0.6 0.5 0.35 0.27 0.40 0.32 Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. Fig 9. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT833-1 --- MO-252 --- EUROPEAN PROJECTION ISSUE DATE 07-11-14 07-12-07 Package outline SOT833-1 (XSON8) 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 14 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate XSON8U: plastic extremely thin small outline package; no leads; 8 terminals; UTLP based; body 3 x 2 x 0.5 mm B D SOT996-2 A A E A1 detail X terminal 1 index area e1 v w b e L1 1 4 8 5 C C A B C M M y y1 C L2 L X 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max A1 b D E e e1 L L1 L2 v w y y1 mm 0.5 0.05 0.00 0.35 0.15 2.1 1.9 3.1 2.9 0.5 1.5 0.5 0.3 0.15 0.05 0.6 0.4 0.1 0.05 0.05 0.1 REFERENCES OUTLINE VERSION IEC SOT996-2 --- JEDEC JEITA --- EUROPEAN PROJECTION ISSUE DATE 07-12-18 07-12-21 Fig 10. Package outline SOT996-2 (XSON8U) 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 15 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate XQFN8U: plastic extremely thin quad flat package; no leads; 8 terminals; UTLP based; body 1.6 x 1.6 x 0.5 mm B D SOT902-1 A terminal 1 index area E A A1 detail X L1 e e C ∅v M C A B ∅w M C L 4 y1 C y 5 3 metal area not for soldering e1 b 2 6 e1 7 1 terminal 1 index area 8 X 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max A1 b D E e e1 L L1 v w y y1 mm 0.5 0.05 0.00 0.25 0.15 1.65 1.55 1.65 1.55 0.55 0.5 0.35 0.25 0.15 0.05 0.1 0.05 0.05 0.05 REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT902-1 --- MO-255 --- EUROPEAN PROJECTION ISSUE DATE 05-11-25 07-11-14 Fig 11. Package outline SOT902-1 (XQFN8U) 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 16 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate 14. Abbreviations Table 11. Abbreviations Acronym Description CDM Charged Device Model CMOS Complementary Metal-Oxide Semiconductor DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model MM Machine Model TTL Transistor-Transistor Logic 15. Revision history Table 12. Revision history Document ID Release date Data sheet status Change notice Supersedes 74AUP1G885_5 20090626 Product data sheet - 74AUP1G885_4 Modifications: • Table 5: Derating factor XSON8, XSON8U and XQFN8U packages has been changed. 74AUP1G885_4 20090401 Product data sheet - 74AUP1G885_3 74AUP1G885_3 20080328 Product data sheet - 74AUP1G885_2 74AUP1G885_2 20070710 Product data sheet - 74AUP1G885_1 74AUP1G885_1 20061201 Product data sheet - - 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 17 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 16.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] 74AUP1G885_5 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 05 — 26 June 2009 18 of 19 74AUP1G885 NXP Semiconductors Low-power dual function gate 18. Contents 1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 12 13 14 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 5 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 13 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 17 Legal information. . . . . . . . . . . . . . . . . . . . . . . 18 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 18 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Contact information. . . . . . . . . . . . . . . . . . . . . 18 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 26 June 2009 Document identifier: 74AUP1G885_5