KOA SPEER ELECTRONICS, INC. TN-200 R7 AHA 06/28/06 Thin Film Chip Inductors Type KL73 Series CERTIFIED CERTIFIED 1. Scope This specification applies to Thin Film Chip Inductors (KL73) 1H, 1E, 1J, 2A and 2B sizes produced by KOA Corporation. 2. Dimensions and Construction L c Inner Electrode t d Coil Pattern Electrode Ceramic Substrate L (Inch Size Code) Marking Protective Coating W Dimensions inches (mm) W c d Type c Insulation Direction Mark Film t 1H (0201) 1E (0402) .024±.001 .01±.001 .003±.002 .006±.002 (0.6±0.03) (0.3±0.03) (0.08±0.05) (0.15±0.05) .039±.004 .02±.002 .006±.004 .01±.004 (1.0±0.1) (0.5±0.05) (0.15±0.1) (0.25±0.1) .009±.001 (0.23±0.03) .014±.002 (0.35±0.05) 1J (0603) .063±.008 .031±.004 .012±.004 .012±.004 (1.6±0.2) (0.8±0.1) (0.3±0.1) (0.3±0.1) .02±.004 (0.5±0.1) 2A (0805) .079±.008 .049±.008 .016±.008 .012±.004 (2.0±0.2) (1.25±0.2) (0.4±0.2) (0.3±0.2) .02±.004 (0.5±0.1) 2B (1206) .126±.008 .063±.008 (3.2±0.2) (1.6±0.2) .016 +.008 -.004 .02±.008 (0.5±0.2) (0.4 +0.2 -0.1 ) .024±.004 (0.6±0.1) 3. Type Designation The type designation shall be the following form: New Type KL73 2A T TE 4N7 G Type Size Termination Material Packaging Nominal Inductance Tolerance 1H: 0201 1E: 0402 1J: 0603 2A: 0805 2B: 1206 T: Sn (Other termination styles available, contact factory for options) TP: 7" Embossed Paper 2mm Pitch (1E only - 10,000 pcs/reel) TE: 7" Embossed Plastic 4mm Pitch (1J, 2A, 2B - 4,000 pcs/reel) TB: 7" Paper Tape 2mm Pitch (1H only - 10,000 pcs/reel) 4N7: 4.7nH 47N: 47nH B: C: G: J: ±0.1nH ±0.2nH ±2% ±5% PAGE 1 OF 9 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 4. Application and Ratings Part Designation Inductance (nH) Inductance Tolerance KL731HTTB0N6* KL731HTTB0N7* KL731HTTB0N8* KL731HTTB0N9* KL731HTTB1N0* KL731HTTB1N1* KL731HTTB1N2* KL731HTTB1N3* KL731HTTB1N5* KL731HTTB1N6* KL731HTTB1N8* KL731HTTB2N0* KL731HTTB2N2* KL731HTTB2N4* KL731HTTB2N7* KL731HTTB3N0* KL731HTTB3N3* KL731HTTB3N6* KL731HTTB3N9* KL731HTTB4N3* KL731HTTB4N7* KL731HTTB5N1* KL731HTTB5N6* KL731HTTB6N2* KL731HTTB6N8* KL731HTTB7N5* KL731HTTB8N2* KL731HTTB9N1* KL731HTTB10N* 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 B: ±0.1nH, C: ±0.2nH KL731HTTB11N* KL731HTTB12N* KL731HTTB13N* KL731HTTB15N* KL731HTTB16N* KL731HTTB18N* 11 12 13 15 16 18 KL731HTTB20N* KL731HTTB22N* KL731HTTB24N* KL731HTTB27N* KL731HTTB33N* KL731HTTB39N* 20 22 24 27 33 39 Quality Factor Minimum Self Resonant Frequency Minimum (MHz) DC Resistance Maximum (Ω) Allowable DC Current Maximum (mA) 0.20 350 B: ±0.1nH B: ±0.1nH, C: ±0.2nH Measured Frequency (MHz) B: ±0.1nH 0.30 B: ±0.1nH, C: ±0.2nH B: ±0.1nH 9000 0.35 B: ±0.1nH, C: ±0.2nH 300 B: ±0.1nH 0.50 B: ±0.1nH, C: ±0.2nH B: ±0.1nH 0.60 B: ±0.1nH, C: ±0.2nH 200 B: ±0.1nH B: ±0.1nH, C: ±0.2nH 0.70 8000 B: ±0.1nH B: ±0.1nH, C: ±0.2nH 130 B: ±0.1nH 1.00 B: ±0.1nH, C: ±0.2nH B: ±0.1nH 5 6000 B: ±0.1nH, C: ±0.2nH 1.30 120 B: ±0.1nH 500 1.50 B: ±0.1nH, C: ±0.2nH G: ±2% G: ±2%, J: ±5% G: ±2% G: ±2%, J: ±5% G: ±2% G: ±2%, J: ±5% G: ±2% 2.00 4000 2.50 2000 5.00 110 70 1500 G: ±2% J: ±5% 1000 6.00 50 800 7.00 40 200 * Add tolerance character (B, C, G, J) PAGE 2 OF 9 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 4. Application and Ratings Continued Part Designation Inductance (nH) KL731ETTPN56B KL731ETTPN68B KL731ETTPN82B KL731ETTP1N0* KL731ETTP1N2* KL731ETTP1N5* KL731ETTP1N8* KL731ETTP2N2* KL731ETTP2N7* KL731ETTP3N3* KL731ETTP3N9* KL731ETTP4N7* KL731ETTP5N6* KL731ETTP6N8* KL731ETTP8N2* KL731ETTP10N* KL731ETTP12N* KL731ETTP15N* KL731ETTP18N* KL731ETTP22N* KL731ETTP27N* KL731ETTP33N* KL731JTTE1N0* KL731JTTE1N2* KL731JTTE1N5* KL731JTTE1N8* KL731JTTE2N2* KL731JTTE2N7* KL731JTTE3N3* KL731JTTE3N9* KL731JTTE4N7* KL731JTTE5N6* KL731JTTE6N8* KL731JTTE8N2* KL731JTTE10N* KL731JTTE12N* KL731JTTE15N* KL731JTTE18N* KL731JTTE22N* KL731JTTE27N* KL731JTTE33N* KL731JTTE39N* KL731JTTE47N* KL731JTTE56N* KL731JTTE68N* KL731JTTE82N* 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 Inductance Tolerance Quality Factor Minimum Self Resonant Frequency Minimum (MHz) DC Resistance Maximum (Ω) B: ±0.1nH 7 14000 0.10 12000 0.15 10000 0.20 8000 0.25 650 0.30 600 550 500 450 B: ±0.1nH C: ±0.2nH 6000 10 0.50 5000 G: ±2% J: ±5% Allowable DC Current Maximum (mA) 700 4000 3000 1.00 2500 1.50 300 250 2000 2.00 3.00 200 5.00 150 0.10 650 500 350 1500 7 Measured Frequency (MHz) 200 1000 10 15 13000 10000 C: ±0.2nH 20 8000 0.15 6000 0.25 5000 0.50 4000 3000 25 2500 450 500 350 1.0 250 1.50 200 2000 1500 G: ±2% J: ±5% 1000 2.50 10 150 200 120 4.00 4.50 5.00 600 100 * Add tolerance character (B, C, G, J) PAGE 3 OF 9 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 4. Application and Ratings Continued Part Designation Inductance (nH) KL732ATTE1N0* KL732ATTE1N2* KL732ATTE1N5* KL732ATTE1N8* KL732ATTE2N2* KL732ATTE2N7* KL732ATTE3N3* KL732ATTE3N9* KL732ATTE4N7* KL732ATTE5N6* KL732ATTE6N8* KL732ATTE8N2* KL732ATTE10N* KL732ATTE12N* KL732ATTE15N* KL732ATTE18N* KL732ATTE22N* KL732ATTE27N* KL732ATTE33N* KL732ATTE39N* KL732ATTE47N* KL732ATTE56N* KL732ATTE68N* KL732ATTE82N* KL732BTTE2N2* KL732BTTE2N7* KL732BTTE3N3* KL732BTTE3N9* KL732BTTE4N7* KL732BTTE5N6* KL732BTTE6N8* KL732BTTE8N2* KL732BTTE10N* KL732BTTE12N* KL732BTTE15N* KL732BTTE18N* KL732BTTE22N* KL732BTTE27N* KL732BTTE33N* KL732BTTE39N* KL732BTTE47N* KL732BTTE56N* KL732BTTE68N* KL732BTTE82N* KL732BTTE100* 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 Inductance Tolerance Self Resonant Frequency Minimum (MHz) Quality Factor Minimum DC Resistance Maximum (Ω) Allowable DC Current Maximum (mA) Measured Frequency (MHz) 13000 20 900 10000 9000 C: ±0.2nH 0.25 8000 800 6000 500 5000 4500 4000 3000 25 700 0.50 500 2500 G: ±2% J: ±5% 400 1.00 2000 1500 20 300 250 1000 1.50 15 200 800 200 4.00 700 10 5.00 600 9000 7000 6000 5000 4500 4000 3500 3000 25 C: ±0.2nH 35 0.25 150 1000 900 900 500 0.50 800 2500 40 2000 1.00 G: ±2% J: ±5% 500 1500 25 1000 400 200 2.00 500 15 200 400 * Add tolerance character (B, C, G, J) PAGE 4 OF 9 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 6. Characteristics 6-1 Test Condition Unless otherwise specified, the standard range of atmospheric conditions for marking measurements and tests is as follows: Ambient temperature: 20 ± 15°C Relative humidity: 65 ± 20% If there may be any doubt on results, measurements shall be made within the following limits: Ambient temperature: 20 ± 2°C Relative humidity: 65 ± 5% 6-2 Measurement Method of L and Q Test equipment: Fixture: Measuring frequency: Hewlett Packard RF Impedance analyzer 4191A Hewlett Packard Test fixture 16092A 500 MHz/1.0nH ~ 22nH (1.0nH ~ 15nH) 200 MHz/27nH ~ 100nH (18nH ~ 47nH) 1. Perform auto-calibration to the HP4191A .275" (7 mm) unknown connector connected to 0Ω/0S/50Ω standard terminations. 2. Connected the test fixture 16092A. Measure the open circuit admittance (Go, Bo), and the short circuit impedance (Ro, Xo). Ro Xo Rx Gm + j Bm Gm Ro Go Rx Bo Go Xx 4191A Caribration plane 16092A Spring clip fixture + jBm: + jXo: + jBo: + jXx: Measured admittance [S] Residual impedance [Ω] Stray admittance [S] Unknown impedance [Q] Coil 3. Set pattern up and ground side to direction mark on insulator. Measure admittance (Gm, Bm). 0402 Chip inductor (Face up) Insulator (Teflon) Spring clip .118 (3.0) .039 (1.0) Grand plane See table Terminal 0603 .055 (1.4) 0805 .071 (1.8) 1206 .106 (2.7) .118 (3.0) Cross section of 16092A .031 (0.8) Thickness: .040 (1.0) Dimensions of insulator (Teflon) in inches (mm) 4. The L and Q value shall be given the following equation. (Compensated calculation) Rx = Xx = Gm - Go - Ro (Gm - Go) 2+ (Bm - Bo)2 Bo - Bm - Xo (Gm - Go) 2- (Bm - Bo)2 L= Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 Xx 2πf ■ USA , ■ L: Inductance of coil Q: Quality factor of coil f: Measuring frequency Q = Xx Rx 814-362-5536 PAGE 5 OF 9 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 6-3 Characteristics Item Requirement Test Method More than 104 MΩ Insulation resistance DC 500V, 1 minute between both terminals and center of reverse side. V More than 103 MΩ DC 500V, 1 minute Between both terminals and center of protection coating. V Without distinct damage Dielectric withstanding voltage DC 500V, 1 minute Between both terminals and center of protection coating. V ∆ R/R: Within ± 1% ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% No mechanical damage by cracks or stripping, etc. Terminal strength Soldered chip on wiring board A for test is to be bent down to .079" (2 mm) - 0603, .118" (3 mm) - 0402, 0805 and 1206 as below drawing. (Set condition) Dimensions in inches (mm) Wiring board A for test Solder Support (ø5) 1.77 (45.0) Chip coil Within ±2 1.77 (45.0) .786 (20) 1.97 (50) Weight .118 (3.0) R230 Ohmmeter PAGE 6 OF 9 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 6-3 Characteristics Continued Item Requirement Test Method Vibration ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction Inflict 2 hours in each direction of X, Y, Z at vibration of JIS C 5025 (1978) type A - 0603; 10 ~ 55Hz, amplitude .059" (1.5 mm) - 0402, 0805 and 1206 Resistance to solder heat ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction 260 ± 5°C, 10 ± 1 second Solderability 95% of the terminal should be covered with new solder 230 ± 5°C, 3 ± 0.5 second Shock resistance ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction Inflict the impulse 3 times to both directions (total 18 times) along perpendicular axis that test condition C of JIS C 5026 (1974) table-1 - 0603; 100G, 6 months - 0402, 0805 and 1206 Low temperature operation ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction -40°C ± 3°C, 1,000 ± 4 hours Heat resisting property ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction 125°C ± 2°C, 1,000 ± 4 hours Temperature cycling ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction -40 ± 3°C, 30 minutes/125 ± 2°C, 30 minutes 100 cycles Humidity ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction. Insulation resistance: more than 50MΩ 40 ± 2°C, 90 ~ 95% RH 1,000 ± 4 hours Resistance to solvent ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance, construction and marking Immerse 30 ± 5 seconds in the regent (20 ~ 25°C) of JIS K 8839 (1995) PAGE 7 OF 9 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 5. Marking 5-1 Coating and Marking Color 5-2 Marking Method Coating color: Dark blue Direction mark color: Yellow 0402 Inductance value shall have no marking. Direction marking only. 0603 Inductance value shall be indicated to two letters marking of figures and alphabet. 0805 Inductance value shall be indicated to two letters marking, including decimal point. Direction mark (Example of marking) L1 1.0nH 56 5.6nH 10 10nH H6 47nH See marking item on page 2, rating table. Direction mark (Example of marking) 2.2 2.2nH 5.6 5.6nH 10 10nH 47 47nH 56 5.6 Decimal point 1206 Inductance value shall be indicated to two letters marking of significant figures. An alphabetical letter N shall replace position of decimal point. Direction mark (Example of marking) 2N2 2.2nH 5N6 5.6nH 10 10nH 47 47nH 5N6 Decimal point 7. Packaging .010 (0.25 ± 0.1) 7-1 Taping The tapes for taping shall be embossed carrier tapes of .315" (8 mm) width and .157" (4 mm) pitches. The standard quantity per reel shall be 4,000 pieces. Tapes for size 0402 (only) shall be paper carrier tapes of .315" (8 mm) width and .079" (2 mm) pitches. .069 (1.75 ± 0.1) .059 (1.5 ± 0.1) .315 (8.0 ± 0.2) Direction of mark A D 5N6 .138 (3.5 ± 0.05) .157 (4.0 ± 0.1) B (1) Dimensions of carrier tape C E Tape running direction Dimensions in inches (mm) Size A B C D E 0402 .018 .026 .045 .079 .079 (0.45 ± 0.2) (0.65 ± 0.1) (1.15 ± 0.1) (2.0 ± 0.05) (2.0 ± 0.05) 0603 .035 .043 .075 .079 .157 (0.90 ± 0.1) (1.1 ± 0.15) (1.9 ± 0.15) (2.0 ± 0.01) (4.0 ± 0.1) 0805 .037 .057 .094 (0.95 ± 0.1) (1.45 ± 0.15) (2.4 ± 0.2) .079 (2.0 ± 0.1) .157 (4.0 ± 0.1) 1206 .037 .074 (0.95 ± 0.1) (1.9 ± 0.2) .079 (2.0 ± 0.1) .157 (4.0 ± 0.1) Bolivar Drive ■ P.O. Box 547 ■ .137 (3.5 ± 0.2) Bradford, PA 16701 ■ USA ■ 814-362-5536 PAGE 8 OF 9 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 (2) Reel dimensions 11.80 (300 ± 20 0 ) 5.90 (150 ± 20 0 ) 13.76 (350 ± 20 0 ) 4,000 pieces Top tape Empty Empty Tape running direction 7.00 (178 ± 2.0) Marking place Dimensions in inches (mm) (Marking item) (1) Type designation (2) Nominal inductance (3) Quantity (4) Production lot number (5) Manufacturer's name .079 (2 ± 0.5) .511 (13 ± 0.5) 2.36 (60 ± 2.0) .393 (10 ± 1.5) .448 (11.4 ± 1.5) 8. Recommended Soldering Condition Dimensions in inches (mm) 8-1 Dimensions of Standard Land A C Solder resist Size A B C 0402 - 1E .016 ~ .020 (0.4 ~ 0.5) .031 ~ .039 (0.8 ~ 1.0) .047 ~ .055 (1.2 ~ 1.4) .079 ~ .094 (2.0 ~ 2.4) .012 ~ .020 (0.3 ~ 0.5) .016 ~ .031 (0.4 ~ 0.8) .035 ~ .051 (0.9 ~ 1.3) .047 ~ .063 (1.2 ~ 1.6) .016 ~ .020 (0.4 ~ 0.5) .016 ~ .031 (0.4 ~ 0.8) .016 ~ .031 (0.4 ~ 0.8) .016 ~ .031 (0.4 ~ 0.8) 0603 - 1J B Chip coil 0805 - 2A Land 1206 - 2B 8-2 Soldering Condition Reflow soldering should be done at 240°C within 20 seconds. Flow soldering should be done at 260°C within 10 seconds. Please use suitable solder quantity, too much solder may affect performance of product. 10. Storage 9. Recommended Washing Condition Chip inductors should not be stored under high temperature and high humidity conditions. In particular, do not store taping where it is exposed to heat or direct sunlight. Otherwise, the packing material may be deformed, causing problems during mounting. Isopropyl alcohol and methyl alcohol used for the washing process will not affect the part performance. Ultrasonic cleaning should be changed to condition for size of printed wiring board and type of oscillator. Overpowering of ultrasonic cleaning will cause problems according to resonant phenomenon. Condition of ultrasonic cleaner should be confirmed prior to use. We recommend the following conditions: Ultrasonic power: Within 20W/1 Cleaning times: Within 5 minutes Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 Solder Solder ■ PAGE 9 OF 9 USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.