PHILIPS P83C380

INTEGRATED CIRCUITS
DATA SHEET
P83Cx80; P87C380
Microcontrollers for monitors
with DDC interface, auto-sync
detection and sync proc.
Product specification
File under Integrated Circuits, IC20
1997 Dec 12
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
CONTENTS
P83Cx80; P87C380
16
DIGITAL-TO-ANALOG CONVERTER (DAC)
16.1
8-bit Data Registers for the DAC outputs
(DACn; n = 0 to 3)
17
DISPLAY DATA CHANNEL (DDC)
INTERFACE
17.1
Special Function Registers related to the DDC
interface
Host type detection
DDC1 protocol
DDC2B protocol
DDC2AB/DDC2B+ protocol
RAM buffer for the system and DDC application
1
FEATURES
1.1
1.2
Differences from the 80C51 core
Memory
2
GENERAL DESCRIPTION
3
ORDERING INFORMATION
4
BLOCK DIAGRAM
5
PINNING INFORMATION
5.1
5.2
Pinning
Pin description
17.2
17.3
17.4
17.5
17.6
6
FUNCTIONAL DESCRIPTION
18
I2C-BUS INTERFACE
6.1
General
19
HARDWARE MODE DETECTION
7
MEMORY ORGANIZATION
19.1
7.1
7.2
7.3
Program memory
Internal data memory
Additional Special Function Registers
19.2
19.3
Special Function Register for mode detection
and sync separation
System description
System operation
8
INTERRUPTS
20
POWER MANAGEMENT
8.1
8.2
8.3
8.4
Priority level structure
How interrupts are handled
Interrupt Enable Register (IE)
Interrupt Priority Register (IP)
21
CONTROL MODES
22
ONE TIME PROGRAMMABLE (OTP)
VERSION
9
WATCHDOG TIMER
23
LIMITING VALUES
10
INPUT/OUTPUT (I/O)
24
HANDLING
10.1
25
DC CHARACTERISTICS
26
10.2
The alternative functions for Port 0, Port 1,
Port 2 and Port 3
EMI (Electromagnetic Interference) reduction
DIGITAL-TO-ANALOG CONVERTER
CHARACTERISTICS
11
REDUCED POWER MODES
27
AC CHARACTERISTICS
28
PACKAGE OUTLINE
29
SOLDERING
Introduction
Soldering by dipping or by wave
Repairing soldered joints
11.1
11.2
11.3
11.4
Power Control Register
Idle mode
Power-down mode
Status of external pins
12
OSCILLATOR
29.1
29.2
29.3
13
RESET
30
DEFINITIONS
13.1
13.2
13.3
External reset
Power-on-reset
T2 (Watchdog Timer) overflow
31
LIFE SUPPORT APPLICATIONS
32
PURCHASE OF PHILIPS I2C COMPONENTS
14
ANALOG CONTROL (DC)
14.1
14.2
14.3
8-bit PWM outputs (PWM0 to PWM9)
14-bit PWM output (PWM10)
A typical PWM output application
15
ANALOG-TO-DIGITAL CONVERTER (ADC)
15.1
Conversion algorithm
1997 Dec 12
2
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
1
P83Cx80; P87C380
• One 8-bit port only for I/O function
FEATURES
• 20 derivative I/O ports with the specific port type
configuration in each alternative function
• 80C51 type core
• On-chip oscillator with a maximum frequency of 16 MHz
(maximum 0.75 µs instruction cycle)
• Watchdog Timer with a programmable interval
• On-chip Power-on-reset for low power detection
• A DDC interface:
• Special Idle and Power-down modes for reduced power
operation
– That fully supports DDC1 with specific hardware
– That is DDC2B, DDC2B+, DDC2AB (ACCESS.bus)
compliant, based on a dedicated hardware I2C-bus
interface.
• Optimized for Electromagnetic Compatibility (EMC)
• Operating temperature: −25 to +85 °C
• Single power supply: 4.4 to 5.5 V.
– Contains a specific AUX-RAM buffer with
programmable size (128 or 256 bytes) that can be
used for DDC operation and shared as system RAM
1.1
• Automatic mode detection by hardware to capture the
following information:
Differences from the 80C51 core
• No external memory connection; signals EA, ALE and
PSEN are not present.
– HSYNC frequency with 12-bit resolution
• Port 1, Port 2 and Port 3 (P3.0 to P3.3 only) mixed with
other derivative functions.
– VSYNC frequency with 12-bit resolution
• Timer 0/Counter 0 and Timer 1/Counter 1: external
input is removed.
– HSYNC and VSYNC polarity
– HSYNC and VSYNC presence; needed for the VESA
Device Power Management Signalling (DPMS)
standard
• External interrupt 0/INT0 replaced by Mode detection
function.
• Standard serial interface (UART) and its control register
are removed.
• On-chip sync processor comprising:
– Composite sync separation
• Wake-up from Power-down mode is also possible by
means of an interrupt.
– Free running mode
– Clamping
– Pattern generation
1.2
• Two specific ports for the software I2C-bus interface
Memory
Table 1
• 4 analog voltage outputs derived from an 8-bit
Digital-to-Analog Converter (DAC)
ROM/RAM sizes
MEMORY
DEVICE
• Ten 8-bit Pulse Width Modulation (PWM) outputs for
digital control application
P83C880
8 kbytes
512 bytes
• One 14-bit PWM output for digital control application
P83C180
16 kbytes
512 bytes
• One 4-bit Analog-to-Digital Converter (ADC) with 2 input
channels (for keyboard interface)
P83C280
24 kbytes
512 bytes
• LED driver port (Port 0); eight port lines with 10 mA drive
capability
P83C380
32 kbytes
512 bytes
P87C380 (OTP)
16 kbytes
512 bytes
1997 Dec 12
ROM
3
RAM
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
2
This data sheet details the specific properties of the
P83C880, P83C180, P83C280, P83C380 and P87C380.
The shared characteristics of the 80C51 family of
microcontrollers are described in “Data Handbook IC20”,
which should be read in conjunction with this data sheet.
GENERAL DESCRIPTION
The P83Cx80; P87C380 denotes the following types:
P83C880, P83C180, P83C280, P83C380 and P87C380,
hereafter referred to as the P83C880, are monitor
microcontrollers of the 80C51 family, with DDC (DDC1,
DDC2B, DDC2B+ and DDC2AB) interface to the PC host.
The internal hardware can separate composite sync
signals and detect the various display modes. The
digital/analog voltage outputs can be used to control the
video and deflection functions the monitor.
3
P83Cx80; P87C380
ORDERING INFORMATION
PACKAGE(1)
VERSION
TEMPERATURE
RANGE (°C)
SOT270-1
−25 to +85
TYPE NUMBER
NAME
P83C880
DESCRIPTION
SDIP42 plastic shrink dual in-line package; 42 leads (600 mil)
P83C180
P83C280
P83C380
P87C380 (OTP)
Note
1. For emulation the package CLCC84 is used.
1997 Dec 12
4
1997 Dec 12
5
(1)
(2)
(3)
(4)
P2
P3
VSYNCin
CSYNCin(1)
HSYNCin
VSYNCout(1)
HSYNCout(1)
PATOUT(3)
CLAMP(3)
MODE
DETECTION
512 BYTES
RAM
SCL1(1)
SDA1(1)
DDC
INTERFACE
4 × 8-BIT
DAC
PWM0 to PWM7(2);
PWM8 to PWM9(3)
10
10 × 8-BIT
PWM
P83C880
P83C180
P83C280
P83C380
P87C380
4-BIT
ADC
Fig.1 Block diagram.
MGG021
RESET
WATCHDOG
TIMER
(T2)
internal reset
PWM10(1)
14-BIT
PWM
8-bit
internal bus
SCL(1)
SOFTWARE
I2C-BUS
SERIAL
I/O
SDA(1)
VDDA
ADC1(3)
Alternative function of Port 1.
Alternative function of Port 2.
Alternative function of Port 3.
ROM: 8 kbytes (P83C880); 16 kbytes (P83C180); 24 kbytes (P83C280); 32 kbytes (P83C380). EPROM: 16 kbytes only in the P87C180A.
P1
4
INT0
(4)
DATA
MEMORY
4
ADC0(3)
VSSA
DAC0 to DAC3
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P0
PARALLEL
I/O PORTS
&
EXTERNAL BUS
CPU
PROGRAM
MEMORY
VSS
k, full pagewidth
80C51
core
excluding
ROM/RAM
TWO 16-BIT
TIMERS
(T0, T1)
VDD
4
XTAL2
XTAL1
INT1
Philips Semiconductors
Product specification
P83Cx80; P87C380
BLOCK DIAGRAM
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
5
5.1
P83Cx80; P87C380
PINNING INFORMATION
Pinning
handbook, halfpage
PWM7/P2.7
1
42 PWM8/CLAMP/P3.0
PWM6/P2.6
2
41 PWM9/PATOUT/P3.1
PWM5/P2.5
3
40 PWM10/P1.7
PWM4/P2.4
4
39 SCL/P1.0
PWM3/P2.3
5
38 SDA/P1.1
PWM2/P2.2
6
37 SCL1/P1.2
PWM1/P2.1
7
36 SDA1/P1.3
PWM0/P2.0
8
35 INT1/VPP
XTAL1
9
XTAL2 10
VDD 11
VSS 12
34 ADC1/P3.3
P83C880
P83C180
P83C280
P83C380
P87C380
33 ADC0/P3.2
32 VDDA
31 VSSA
HSYNCin/PROG 13
30 DAC3
HSYNCout/P1.5 14
29 DAC2
CSYNCin/P1.6 15
28 DAC1
VSYNCin/OE 16
27 DAC0
VSYNCout/P1.4 17
26 RESET
P0.7 18
25 P0.0
P0.6 19
24 P0.1
P0.5 20
23 P0.2
P0.4 21
22 P0.3
MGG020
Fig.2 Pinning configuration for SDIP42.
1997 Dec 12
6
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
5.2
P83Cx80; P87C380
Pin description
Table 2
Pin description for SDIP42 (SOT270-1)
SYMBOL
PIN
DESCRIPTION
PWM9/PATOUT/P3.1
41
PWM8/CLAMP/P3.0
42
PWM7/P2.7
1
PWM9 to PWM0: 8-bit Pulse Width Modulation outputs 9 to 0. Pin 41 and 42 can
also be used as the output pin of the test pattern display PATOUT and clamping out
signal CLAMP respectively; PATOUT and CLAMP always have the higher priority.
PWM6/P2.6
2
PWM5/P2.5
3
PWM4/P2.4
4
PWM3/P2.3
5
PWM2/P2.2
6
PWM1/P2.1
7
PWM0/P2.0
8
XTAL1
9
XTAL2
10
Oscillator output pin for system clock.
VDD
11
Digital power supply (+5 V).
VSS
12
Digital ground.
HSYNCin/PROG
13
Horizontal sync input pin. During OTP programming it is used as the program pulse
input (PROG).
HSYNCout/P1.5
14
Horizontal sync output pin; alternative function: general I/O port P1.5.
CSYNCin/P1.6
15
Composite sync input pin; alternative function: general I/O port P1.6.
VSYNCin/OE
16
Vertical sync input pin. During OTP programming it is used as output strobe (OE).
VSYNCout/P1.4
17
Vertical sync output pin; alternative function: general I/O port P1.4.
P0.7 to P0.0
RESET
DAC0 to DAC3
Alternative function general I/O ports; Port 3: P3.1 to P3.0 and
Port 2: P2.7 to P2.0.
Oscillator input pin for system clock.
18 to 25 Port 0: general I/O ports; capability to drive LED.
26
Reset input; active HIGH initializes the device.
27 to 30 8-bit DAC analog voltage output pins; output range: 0 to 5 V.
VSSA
31
Analog ground for DAC and ADC.
VDDA
32
Analog power supply (+5 V) for DAC and ADC.
ADC0/P3.2
33
ADC analog input pins; alternative function: general I/O ports P3.2 and P3.3.
ADC1/P3.3
34
INT1/VPP
35
External interrupt input pin. During OTP programming it is used as programming
supply voltage pin; VPP = 12.75 V.
SDA1/P1.3
36
I2C-bus serial data I/O port for the DDC2 interface; alternative function: general I/O
port P1.3.
SCL1/P1.2
37
I2C-bus serial clock I/O port for the DDC2 interface; alternative function: general I/O
port P1.2.
SDA/P1.1
38
I2C-bus serial data I/O port; alternative function: general I/O port P1.1.
SCL/P1.0
39
I2C-bus serial clock I/O port; alternative function: general I/O port P1.0.
PWM10/P1.7
40
14-bit Pulse Width Modulation output 10; alternative function: general I/O port P1.7.
1997 Dec 12
7
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
6
P83Cx80; P87C380
In addition to the 80C51 standard functions, they provide a
number of dedicated hardware functions for monitor
application. Eight general I/O ports plus 20 functions
combined I/O ports cater for application requirements
adequately.
FUNCTIONAL DESCRIPTION
This chapter gives a brief overview of the device.
Detailed functional descriptions are given in the following
chapters:
Chapter 7 “Memory organization”
Ten sets of 8-bit PWM deliver the digital waveform for
analog control purposes. One 14-bit PWM can support
F to V application. The keyboard interface is achieved via
a 4-bit ADC. A Watchdog Timer with a maximum count
period of 5 s prevents the processor running out of control
due to malfunction. Four channels of linear DAC with 8-bit
resolution support more accurate analog controls.
Chapter 8 “Interrupts”
Chapter 9 “Watchdog Timer”
Chapter 10 “Input/Output (I/O)”
Chapter 11 “Reduced power modes”
Chapter 12 “Oscillator”
Chapter 13 “Reset”
Chapter 20 “Power management”
One software I2C-bus interface is dedicated for the internal
connection. A DDC interface will cover all DDC protocols,
including DDC1, DDC2B, DDC2AB and DDC2B+.
A hardware mode detector will facilitate mode detection
even in power reduced modes, e.g. Idle mode.
The versatile HSYNC and VSYNC outputs can be
generated to serve the desired application. In the free
running mode, two display patterns can highlight the status
of the monitor. Accordingly, the following items will be
supported by these microcontrollers:
Chapter 21 “Control modes”.
• Mode detection for:
Chapter 14 “Analog control (DC)”
Chapter 15 “Analog-to-digital converter (ADC)”
Chapter 16 “Digital-to-analog converter (DAC)”
Chapter 17 “Display Data Channel (DDC) interface”
Chapter 18 “I2C-bus Interface”
Chapter 19 “Hardware mode detection”
6.1
– Horizontal sync (HSYNC) frequencies from below
15 kHz up to 150 kHz
General
The P83C880, P83C180, P83C280, P83C380 and
P87C380 8-bit microcontrollers are manufactured in an
advanced CMOS process and are derivatives of the
80C51 microcontroller family. They have the same
instruction set as the 80C51.
– Vertical sync (VSYNC) frequencies from below 40 Hz
up to 200 Hz
• ACCESS.bus interfacing with external devices, e.g. PCs
• DDC1, DDC2B, DDC2AB and DDC2B+ protocols as
defined in the VESA DDC standard
They contain 512 bytes of data memory (RAM). ROM:
8 kbytes (P83C880); 16 kbytes (P83C180); 24 kbytes
(P83C280); 32 kbytes (P83C380) and 16 kbytes of
EPROM for the P87C180. The microcontrollers are
intended for use in monitors ranging from 14" to 21" that
can be controlled from the outside (e.g. by a PC) via the
external DDC interface.
1997 Dec 12
• Device Power Management Signalling (DPMS) as
described in VESA DPMS proposal.
Figure 1 shows the block diagram functions.
8
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
7
P83Cx80; P87C380
MEMORY ORGANIZATION
The Central Processing Unit (CPU) manipulates operands in two memory spaces. There are 512 bytes of internal data
memory, consisting of 256 bytes standard RAM and 256 bytes RAM buffer which is accessible as the Auxiliary RAM
(AUX-RAM) or addressed through DDCADR and RAMBUF. The memory map and address spaces are shown in Fig.3.
overlapped space
andbook, full pagewidth
32767(1)
24575(2)
16383(3)
8191(4)
255
255
SPECIAL
FUNCTION
REGISTERS
INDIRECT
ONLY
INTERNAL
AUX-RAM
BUFFER
127
DIRECT AND
INDIRECT
0
0
0
internal data memory area
program memory area
(1)
(2)
(3)
(4)
INDIRECT
ONLY
MGG028
P83C380 and P87C380.
P83C280.
P380C180.
P83C880.
Fig.3 Memory map and address spaces.
7.1
Program memory
The program memory consists of ROM: 8 kbytes (P83C880), 16 kbytes (P83C180), 24 kbytes (P83C280) and 32 kbytes
(P83C380). The program memory implemented in the P87C380 is a 16 kbytes EPROM (OTP).
7.2
Internal data memory
The internal data memory is divided into three physically separated parts: 256 bytes of RAM, 256 bytes of AUX-RAM,
and a 128 bytes Special Function Registers (SFRs) area. These can be addressed each in a different way as described
in Sections 7.2.1 to 7.2.3 and Table 3.
Table 3
Internal data memory map
ADDRESS MODE
MEMORY
RAM
LOCATION
0 to 127(1)
POINTERS
DIRECT
INDIRECT
X
X
−
X
AUX-RAM 0 to 255
−
X(3)
SFRs
X
−
128 to
255(2)
128 to 255
address pointers are R0 and R1 of the selected register bank
address pointer DDCADR and RAMBUF
−
Notes
1. RAM locations 0 to 127 can be addressed directly and indirectly as in the 80C51.
2. RAM locations 128 to 255 can only be addressed indirectly.
1997 Dec 12
9
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
3. Indirect-addressable via MOVX-Datapointer or
MOVX-Ri instructions.
7.2.1
BYTE
ADDRESS
(HEX)
RAM
Four register banks, each 8 registers wide, occupy
locations 0 through 31 in the lower RAM area. Only one of
these banks may be enabled at a time. The next 16 bytes,
locations 32 through 47, contain 128 directly addressable
bit locations. The stack can be located anywhere in the
internal 256 bytes RAM. The stack depth is only limited by
the available internal RAM space of 256 bytes (see Fig.4).
7.2.2
SPECIAL FUNCTION REGISTERS (SFRS)
The SFRs can only be addressed directly in the address
range from 128 to 255 (see Fig.3). Figure 5 gives an
overview of the Special Function Registers space. Sixteen
address in the SFRs space are both byte and
bit-addressable. The bit-addressable SFRs are those
whose address ends in 0H and FH. The bit addresses in
this area are 80H to FFH
7.2.3
AUX-RAM
AUX-RAM buffer 0 to 255 is indirectly addressable as
external data memory locations 0 to 255 via
MOVX-Datapointer instruction or via MOVX-Ri instruction.
Since the external access function is not available, any
access to AUX-RAM 0 to 255 will not affect the ports.
BYTE
ADDRESS
(DECIMAL)
BIT ADDRESS
(HEX)
(MSB)
2FH
2EH
7F
77
7E
76
7D
75
7C
74
7B
73
7A
72
79
71
78
70
47
46
2DH
2CH
6F
67
6E
66
6D
65
6C
64
6B
63
6A
62
69
61
68
60
45
44
2BH
2AH
29H
5F
57
4F
5E
56
4E
5D
55
4D
5C
54
4C
5B
53
4B
5A
52
4A
59
51
49
58
50
48
43
42
41
28H
27H
47
46
45
44
43
42
41
40
3F
3E
3D
3C
3B
3A
39
38
40
39
26H
25H
24H
37
2F
36
2E
35
2D
34
2C
33
2B
32
2A
31
29
30
28
27
26
25
24
23
22
21
20
38
37
36
23H
22H
1F
17
1E
16
1D
15
1C
14
1B
13
1A
12
19
11
18
10
35
34
21H
20H
1FH
0F
07
0E
06
0D
05
0C
04
0B
03
0A
02
09
01
08
00
33
32
31
(LSB)
BANK 3
18H
17H
24
23
BANK 2
The 256 bytes of AUX-RAM buffer used to support DDC
interface is also available for system usage by indirect
addressing through the address pointer DDCADR and
data I/O buffer RAMBUF. The address pointer (DDCADR)
is equipped with the post increment capability to facilitate
the transfer of data in bulk (for details refer to Chapter 17).
However, it is also possible to address the AUX-RAM
buffer through MOVX command as usually used in the
internal RAM extension of 80C51 derivatives.
10H
0FH
16
15
BANK 1
08H
07H
8
7
BANK 0
00H
0
MBH079
Fig.4 RAM bit addresses.
1997 Dec 12
255
FFH
10
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
handbook, full pagewidthBYTE ADDRESS
BIT ADDRESS
(HEX)
(HEX)
FFH
P83Cx80; P87C380
BYTE ADDRESS
(DECIMAL)
(MSB)
(LSB)
F8H
FF
FE
FD
FC
FB
FA
F9
F8
MDCST
F0H
F7
F6
F5
F4
F3
F2
F1
F0
B
E8H
EF
EE
ED
EC
EB
EA
E9
E8
PWME2
E0H
E7
E6
E5
E4
E3
E2
E1
E0
ACC
D8H
DF
DE
DD
DC
DB
DA
D9
D8
S1CON
D0H
D7
D6
D5
D4
D3
D2
D1
D0
PSW
C8H
CF
CE
CD
CC
CB
CA
C9
C8
PWME1
C0H
C7
C6
C5
C4
C3
C2
C1
C0
DFCON
B8H
BF
BE
BD
BC
BB
BA
B9
B8
IP0
B0H
B7
B6
B5
B4
B3
B2
B1
B0
P3
A8H
AF
AE
AD
AC
AB
AA
A9
A8
IEN0
A0H
A7
A6
A5
A4
A3
A2
A1
A0
P2
98H
9F
9E
9D
9C
9B
9A
99
98
not used
90H
97
96
95
94
93
92
91
90
P1
88H
8F
8E
8D
8C
8B
8A
89
88
TCON
80H
87
86
85
84
83
82
81
80
P0
MGG029
Fig.5 Special Function Registers bit addresses.
1997 Dec 12
255
11
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
7.3
P83Cx80; P87C380
Additional Special Function Registers
The standard SFRs as used in 80C51 and the SFRs for some typical derivative functions like I2C-bus interface, Timer,
etc. are described in the “Data Handbook IC20”. The specific SFRs for the P83C880 are introduced in the relevant
chapters. Some SFRs which are not mentioned or not dedicated to a certain function will be described in the following
sections.
All new additional SFRs used in the P83C880 are listed in Table 4. However, only some of them will be explained in detail
in Sections 7.3.1 to 7.3.7.
Table 4
Overview of additional SFRs
REGISTER
DESCRIPTION
ADDRESS
RESET VALUE(1) READ/WRITE(2)
RAMBUF
RAM Buffer I/O Interface Register
9CH
XXXXXXXX
B
DDCCON
DDC Control Register
9DH
X00X0000
UBBUBBBB
DDCADR
DDC Address Pointer
9EH
00000000
B
DDCDAT
Data Shift Register for DDC1
9FH
00000000
B
DFCON
Miscellaneous Control Register
C0H
10000000
B
ADCDAT
ADC Control Register
C1H
XX000000
UUBBBBBRO
PWM10H
PWM High-byte Data Latch
C6H
00000000
B
PWM10L
PWM Low-byte Data Latch
C7H
10000000
B
S1CON
Control Register for DDC2
D8H
00000000
B
S1STA
Status Register for DDC2
D9H
11111000
Ro
S1DAT
Data Shift Register for DDC2
DAH
00000000
B
S1ADR
Address Register for DDC2
DBH
00000000
B
PWME1
PWM Output Control Register 1
C8H
00000000
B
PWME2
PWM Output Control Register 2
E8H
00000000
B
PWM0 to PWM9
Data Latches for 8-bit PWMs
C9H to CFH,
EDH to EFH
00000000
B
DAC0 to DAC3
8-bit Data Latches for 8-bit DACs
E9H to ECH
00000000
B
HFP
Free run Control Register for HSYNCout
F6H
01100000
B
HFPOPW
Free run and Pulse width for HSYNCout
F7H
00011111
B
MDCST
Mode Detect Control and Status Register
F8H
1X000000
BUBBRRRR
VFP
Free run Control Register for VSYNCout
F9H
01000000
B
VFPOPW
Free run and Pulse width for VSYNCout
FAH
XX000101
B
PULCNT
Pulse Generation Control Register
FBH
00000000
B
HFHIGH
Horizontal Period Counting High-byte
Register
FCH
00000000
Ro
VFHIGH
Vertical Period Counting High-byte Register
FDH
00000000
Ro
VFLHFL
Vertical and Horizontal Period Counting
Low-nibbles Register
FEH
00000000
Ro
T2
Watchdog Timer Data Register
FFH
00000000
B
Notes
1. X = don’t care; even if it’s implemented.
2. B = both read/write and Ro = read only; accessible for the entire byte or an individual bit. U = not implemented.
1997 Dec 12
12
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
7.3.1
P83Cx80; P87C380
RAM BUFFER I/O INTERFACE REGISTER (RAMBUF)
RAMBUF is used as an I/O interface to the RAM buffer. If it is associated with the address pointer DDCADR which is
equipped with the capability of post increment, then it will be convenient to transfer the consecutive data stream. This
feature is useful to support the DDC/EDID data transfer.
Table 5
RAM Buffer I/O Interface Register (SFR address 9CH)
7
6
5
4
3
2
1
0
RAMBUF.7
RAMBUF.6
RAMBUF.5
RAMBUF.4
RAMBUF.3
RAMBUF.2
RAMBUF.1
RAMBUF.0
Table 6
Description of RAMBUF bits
BIT
SYMBOL
7 to 0
7.3.2
DESCRIPTION
RAMBUF.7 to RAMBUF.0
8-bit data which is read from or to be written into RAM buffer
MISCELLANEOUS CONTROL REGISTER (DFCON)
This register is bit-addressable.
Table 7
Miscellaneous Control Register (SFR address C0H)
7
6
5
4
3
2
1
0
EW2
SOGE
SYNCE
DDCE
S1E
ADCE
P14LVL
P8LVL
Table 8
Description of DFCON bits
BIT
SYMBOL
7
EW2
Watchdog Timer enable flag. This flag is associated with the flags, EW1 (SFR
PWM10H) and EW0 in (SFR PWM10L) to form the enable/disable control key for the
Watchdog Timer (see Chapter 9). The Watchdog Timer is only disabled by
EW2 to EW0 = 101, else it is kept enabled for the rest of the combinations.
6
SOGE
CSYNCin enable for pin CSYNCin/P1.6. If SOGE = 1, the pin function is CSYNCin. If
SOGE = 0, the pin function is I/O port P1.6.
5
SYNCE
Sync separated signals output enable for pins VSYNCout/P1.4 and HSYNCout/P1.5.
If SYNCE = 1, the pins function as VSYNCout and HSYNCout respectively.
If SYNCE = 0, the pins function as I/O ports P1.4 and P1.5 respectively.
4
DDCE
Enable for DDC interface pins SCL1/P1.2 and SDA1/P1.3. If DDCE = 1, the pins
function as SCL1 and SDA1 respectively for the DDC interface. If DDCE = 0, the pins
function as I/O ports P1.2 and P1.3 respectively.
3
S1E
1997 Dec 12
DESCRIPTION
Enable for I2C-bus interface pins SCL/P1.0 and SDA/P1.1. If S1E = 1, the pins
function as SCL and SDA respectively for the I2C-bus interface. If S1E = 0, the pins
function as I/O ports P1.0 and P1.1 respectively.
13
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
BIT
SYMBOL
DESCRIPTION
2
ADCE
ADC channel enable. This flag enables the ADC function and also switches the pins
ADC0/P3.2 and ADC1/P3.3 to the ADC inputs function. If ADCE = 1, the ADC function
is enabled and the pin functions are ADC0 and ADC1 respectively. If ADCE = 0, the
ADC function is disabled and the pin functions are I/O ports P3.2 and P3.3 respectively.
1
P14LVL
Polarity selection bit for the PWM10 output (14-bit PWM). If P14LVL = 1, PWM10
output is inverted. If P14LVL = 0, PWM10 output is not inverted.
0
P8LVL
Polarity selection bit for the PWM0 to PMM9 outputs (8-bit PWM). If P8LVL = 1,
PWM0 to PWM9 outputs are inverted. If P8LVL = 0, PWM0 to PWM9 outputs are not
inverted.
7.3.3
ADC CONTROL REGISTER (ADCDAT)
Table 9
ADC Control Register (SFR address C1H)
7
6
5
4
3
2
1
0
−
−
DACHL
DAC3
DAC2
DAC1
DAC0
COMP
Table 10 Description of ADCDAT bits
BIT
SYMBOL
DESCRIPTION
7 to 6
−
5
DACHL
ADC input channels selection. If DACHL = 1, then input channel
ADC1 is selected. If DACHL = 0, then input channel ADC0 is selected.
4 to 1
DAC3 to DAC0
Reference voltage level selection. The 4 bits select the analog output
voltage (Vref) of the 8-bit DAC. For Vref values see Table 31.
0
COMP
Comparison result; read only. If COMP = 1, then the ADC input
voltage is higher than the reference voltage. If COMP = 0, then the ADC
input voltage is lower than the reference voltage.
Reserved.
14-BIT PWM DATA LATCHES (PWM10H AND PWM10L)
7.3.4
Table 11 PWM High-byte Data Latch (PWM10H; SFR address C6H)
7
6
5
4
3
2
1
0
EW1
PWM10H.6
PWM10H.5
PWM10H.4
PWM10H.3
PWM10H.2
PWM10H.1
PWM10H.0
Table 12 Description of PWM10H bits
BIT
SYMBOL
DESCRIPTION
7
EW1
Watchdog Timer enable flag. This flag is associated with the flag EW2
(SFR DFCON) and EW0 (SFR PWM10L) to form the enable/disable
control key for the Watchdog Timer; see Tables 8 and 14.
6 to 0
PWM10H.6 to PWM10H.0
1997 Dec 12
7 upper data bits for the 14-bit PWM.
14
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
Table 13 PWM Low-byte Data Latch (PWM10L; SFR address C7H)
7
6
5
4
3
2
1
0
EW0
PWM10L.6
PWM10L.5
PWM10L.4
PWM10L.3
PWM10L.2
PWM10L.1
PWM10L.0
Table 14 Description of PWM10L bits
BIT
SYMBOL
DESCRIPTION
7
EW0
Watchdog Timer enable flag. This flag is associated with the flag EW2
(SFR DFCON) and EW1 (SFR PWM10H) to form the enable/disable
control key for the Watchdog Timer; see Table 8 and 12.
6 to 0
PWM10L.6 to PWM10L.0
7 lower data bits for the 14-bit PWM.
PWM OUTPUT CONTROL REGISTER 1 (PWME1)
7.3.5
Table 15 PWM Output Control Register 1 (SFR address C8H)
7
6
5
4
3
2
1
0
PWME1.7
PWME1.6
PWME1.5
PWME1.4
PWME1.3
PWME1.2
PWME1.1
PWME1.0
Table 16 Description of PWME1 bits
BIT
SYMBOL
DESCRIPTION
7 to 0
PWME1.7
to
PWME1.0
PWM outputs enable; n = 7 to 0. If PWME1.n = 1, the corresponding PWM is enabled
and pins PWMn/P2.n are switched to PWMn outputs. If PWME1.n = 0, the
corresponding PWM is disabled and pins PWMn/P2.n are switched to I/O ports P2.n
function.
1997 Dec 12
15
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
7.3.6
P83Cx80; P87C380
PWM OUTPUT CONTROL REGISTER 2 (PWME2)
Table 17 PWM Output Control Register 2 (SFR address E8H)
7
6
5
4
3
2
1
0
PATENA
DACE3
DACE2
DACE1
DACE0
PWME2.2
PWME2.1
PWME2.0
Table 18 Description of PWME2 bits
BIT
SYMBOL
DESCRIPTION
7
PATENA
PATOUT (pattern output) enable. If PATENA = 1, the pin
PWM9/PATOUT/P3.1 is switched to the PATOUT (display test pattern)
output. If PATENA = 0, the PATOUT function is disabled. The PATOUT
function always overrides other alternative functions such as PWM9 and
P3.1.
6 to 3
DACE3 to DACE0
2 to 0
PWME2.2 to PWME2.0
7.3.7
DAC outputs enable (n = 3 to 0). If DACEn = 1, the corresponding
DACs: DAC3 to DAC0 are enabled. If DACEn = 0, the corresponding
DACs: DAC3 to DAC0 are disabled.
PWM outputs enable; n = 2 to 0. If PWME2.n = 1, the corresponding
PWMs: PWM8, PWM9 and PWM10, are enabled by PWME2.2,
PWME2.1 and PWME2.0 respectively and pins PWM8/CLAMP/P3.0,
PWM9/PATOUT/P3.1 and PWM10/P1.7 are switched to PWM output. If
PWME2.n = 0, the corresponding PWM is disabled. Pins
PWM8/CLAMP/P3.0, PWM9/PATOUT/P3.1 and PWM10/P1.7 are
switched to I/O port functions P3.0, P3.1 and P1.7 respectively.
DATA LATCHES FOR 8-BIT PWMS (PWM0 TO PWM9)
Table 19 Data Latches for 8-bit PWMs (n = 0 to 9; SFR address C9H to CFH and EDH to EFH)
7
6
5
4
3
2
1
0
PWMn.7
PWMn.6
PWMn.5
PWMn.4
PWMn.3
PWMn.2
PWMn.1
PWMn.0
Table 20 Description of PWM0 to PWM9 bits
BIT
SYMBOL
7 to 0
PWMn.7 to PWMn.0
1997 Dec 12
DESCRIPTION
8-bit data for PWM channel n (n = 0 to 9)
16
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
8
Each of these interrupts sources can be individually
enabled or disabled by setting or clearing the bit in Special
Function Register IE (see Table 23). IE also contains a
global disable bit EA, which disables all interrupts at once.
INTERRUPTS
The P83C880 has 5 interrupt sources; these are shown in
Fig.6.
Interrupt INT1 is generated as in a normal 80C51 device.
By means of IT1 in SFR TCON this interrupt can be
selected to be:
8.1
Priority level structure
The priority level of each interrupt source can be
individually programmed by setting or clearing a bit in
Special Function Register IP (see Table 25). A low priority
interrupt can itself be interrupted by a high priority
interrupt, but not by another low priority interrupt. A high
priority interrupt can not be interrupted by another interrupt
source.
• Level sensitive, when IT1 = LOW; INT1 must be inactive
before a return from interrupt instruction (RETI) is given,
otherwise the same interrupt will occur again.
• Edge sensitive, when IT1 = HIGH; the internal hardware
will reset the latch when the LCALL instruction is
executed for the vector address (see Table 21).
If two requests of different priority levels are received
simultaneously, the request of higher priority level is
serviced. If request of the same priority level is received
simultaneously, an internal polling sequence determines
which request is serviced. Thus within each priority level
there is a second priority structure determined as shown in
Table 21. The IP register contains a number of reserved
(in 80C51) bits: IP.7, IP.6 and IP.4. User software should
not write logic 1s to these positions, since they may be
used in other 80C51 family products.
Interrupt INT0 is generated by the mode change of mode
detector. Interrupt INT0 is selected as edge or level
sensitive by the state of the IT0 bit in the SFR TCON.
However, it is recommended to always set IT0 to HIGH
(edge sensitive) so that IE0 will be reset by the internal
hardware when the LCALL instruction is executed for the
vector address.
Timer 0 and Timer 1 interrupts are generated by TF0 and
TF1 which are set by an overflow of their respective
Timer/Counter registers (except for Timer 0 in Mode 3;
see “Data Handbook IC20; 80C51 Family; Chapter
Timer/Counters”). When a timer interrupt is generated, the
interrupt flag is cleared by the internal hardware when the
LCALL instruction is executed for the vector address.
Table 21 Priority within levels
The DDC interrupt is generated either by bit SI (SFR
S1CON) for DDC2B/DDC2AB/DDC2B+ protocols or by bit
DDC_int (SFR DDCCON) or by bit SWHINT (SFR
DDCCON). These flags must be cleared by software.
All bits that generate interrupts can be set or cleared by
software, with the same result as though it had been set or
cleared by hardware. That is, interrupts can be generated
or pending interrupts can be cancelled in software.
1997 Dec 12
P83Cx80; P87C380
SOURCE
PRIORITY WITHIN LEVEL(1)
IE0′
1 (highest)
SI
2
TF0
3
IE1′
4
TF1
5 (lowest)
Note
1. The ‘Priority within level’ structure is only used to
resolve simultaneous requests of the same priority
level.
17
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
handbook, full pagewidth
mode change interrupt
INT0
P83Cx80; P87C380
'0'
MUX
IT0
CHREQ
IE0´
'1'
IE0
SWITCH interrupt
SWH INT
SI
DDC1 interrupt
DDC INT
DDC2 (DDC2B/DDC2AB/DDC2B+) interrupt
S12
interrupt
sources
Timer 0 overflow
external interrupt INT1
TF0
INT1
TF0
'0'
MUX
IT1
IE1´
'1'
IE1
Timer 1 overflow
TF1
TF1
MGG024
Fig.6 Interrupt sources.
1997 Dec 12
18
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
8.2
Note that if an interrupt of higher priority level becomes
active prior to S5P2 of the machine cycle labelled C3 (see
“Data Handbook IC20; 80C51 family hardware description;
Figure: Interrupt Response Timing Diagram”), then in
accordance with the above rules it will be vectored to
during C5 and C6, without any instruction of the lower
priority routine having been executed. Thus the processor
acknowledges an interrupt request by executing a
hardware generated LCALL to the appropriate servicing
routine. The hardware generated LCALL pushes the
contents of the Program Counter on to the stack (but it
does not save the PSW) and reloads the PC with an
address that depends on the source of the interrupt being
vectored to as shown in Table 22.
How interrupts are handled
The interrupt flags are sampled at the S5P2 state of every
machine cycle. The samples are polled during the
following machine cycle. If one of the flags was in a set
condition at S5P2 of the preceding cycle, the polling cycle
will find it and the interrupt system will generate an LCALL
to the appropriate service routine, provided this hardware
generated LCALL is not blocked by any of the following
conditions:
1. An interrupt of equal priority or higher priority level is
already in progress.
2. The current (polling) cycle is not the final cycle in the
execution of the instruction in progress.
3. The instruction in progress is RETI or any write to the
IE or IP registers.
Execution proceeds from that location until the RETI
instruction is encountered. The RETI instruction informs
the processor that the interrupt routine is no longer in
progress, then pops the top two bytes from the stack and
reloads the Program Counter. Execution of the interrupted
program continues from where it left off.
Any of these conditions will block the generation of the
LCALL to the interrupt service routine. Condition 2
ensures that the instruction in progress will be completed
before vectoring to any service routine.
Note that a simple RET instruction would also return
execution to the interrupted program, but it would have left
the interrupt control system thinking an interrupt was still in
progress, making future interrupts impossible.
Condition 3 ensures that if the instruction in progress is
RETI or any access to IE or IP, then at least one more
instruction will be executed before the interrupt is vectored
to.The polling cycle is repeated with each machine cycle,
and the values polled are the values that were present at
S5P2 of the previous machine cycle. Note that if an
interrupt flag is active but not being responded to for one
of the above mentioned conditions, and if the flag is still
inactive when the blocking condition is removed, then the
denied interrupt will not be serviced. In other words, the
fact that the interrupt flag was once active but not serviced
is not remembered. Every polling cycle is new.
Table 22 Vector addresses
The polling cycle/LCALL sequence is illustrated in “Data
Handbook IC20; 80C51 family hardware description;
Figure: Interrupt Response Timing Diagram”.
1997 Dec 12
P83Cx80; P87C380
19
SOURCE
VECTOR ADDRESS
IE0′
0003H
SI
002BH
TF0
000BH
IE1′
0013H
TF1
001BH
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
8.3
P83Cx80; P87C380
Interrupt Enable Register (IE)
Table 23 Interrupt Enable Register (SFR address A8H)
7
6
5
4
3
2
1
0
EA
−
ES1
−
ET1
EX1
ET0
EX0
Table 24 Description of IE bits
8.4
BIT
SYMBOL
FUNCTION
7
EA
Disable all interrupts. If EA = 0, then no interrupt will be acknowledged. If EA = 1, then
each interrupt source is individually enabled or disabled by setting or clearing its enable
bit.
6
−
5
ES1
4
−
3
ET1
Enable Timer 1 overflow interrupt. If ET1 = 1, then the Timer 1 interrupt is enabled.
If ET1 = 0, then the Timer 1 interrupt is disabled.
2
EX1
Enable external interrupt 1. If EX1 = 1 then the External 1 interrupt is enabled.
If EX1 = 0 then the External 1 interrupt is disabled.
1
ET0
Enable Timer 0 overflow interrupt. If ET0 = 1 then the Timer 0 interrupt is enabled.
If ET0 = 0 then the Timer 0 interrupt is disabled.
0
EX0
Enable mode change. If EX0 = 1 then the mode change interrupt is enabled.
If EX0 = 0 then the mode change interrupt is disabled.
Reserved.
Enable DDC interface interrupt. If ES1 = 1, then DDC interface interrupt is enabled.
If ES1 = 0, then DDC interface interrupt is disabled.
Reserved.
Interrupt Priority Register (IP)
Table 25 Interrupt Priority Register (address B8H)
7
6
5
4
3
2
1
0
−
−
PS1
−
PT1
PX1
PT0
PX0
Table 26 Description of IP bits
BIT
SYMBOL
DESCRIPTION
−
Reserved.
5
PS1
DDC interface Interrupt priority level. When PS1 = 1, DDC interface Interrupt is
assigned a high priority level.
4
−
Reserved.
3
PT1
Timer 1 overflow interrupt priority level. When PT1 = 1, Timer 1 Overflow Interrupt is
assigned a high priority level.
2
PX1
External interrupt 1 priority level. When PX1 = 1, External Interrupt 1 priority is
assigned a high priority level.
1
PT0
Timer 0 overflow interrupt priority level. When PT0 = 1, Timer 0 Overflow Interrupt is
assigned a high priority level.
0
PX0
Mode change interrupt priority level. When PX0 = 1, Mode change Interrupt is
assigned a high priority level.
7 to 6
1997 Dec 12
20
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
9
P83Cx80; P87C380
The Watchdog Timer’s time interval is:
1024
t = t 1 × ----------------------------( 256 – T2 )
WATCHDOG TIMER
In addition to the standard timers, a Watchdog Timer
consisting of an 10-bit prescaler and an 8-bit timer is also
incorporated. The timer is increased every 19.5 ms for an
oscillator frequency of 16 MHz; this is derived from the
oscillator frequency (fclk) by the formula:
Where T2 = decimal value of the T2 register contents and
t1 = 15.2 µs (fclk = 10 MHz); t1 = 12.7 µs (fclk = 12 MHz)
and t1 = 19 µs (fclk = 16 MHz).
f clk
f timer = ---------------------------304 × 1024
For example, this may range from 19.5 ms to 5.0 s when
using an oscillator frequency of 16 MHz.
When a timer overflow occurs, the microcontroller is reset.
To prevent a system reset, the timer must be reloaded
before an overflows occurs, by the application software.
If the processor suffers a hardware/software malfunction,
the software will fail to reload the timer. This failure will
produce a reset upon overflow thus preventing the
processor running out of control.
Table 27 lists the resolution and the maximum time interval
of the Watchdog Timer using different system clocks.
The Watchdog Timer can only be reloaded if the condition
flag WLE (PCON.4) has been previously set by software.
At the moment the counter is loaded the condition flag is
automatically cleared.
• EW0; PWM10L.7 (SFR address C6H).
The Watchdog Timer is controlled by the Watchdog control
bits:
• EW2; DFCON.7 (SFR address C0H)
• EW1; PWM10H.7 (SFR address C6H)
Only when EW2 to EW0 = 101 the Watchdog Timer is
disabled and allows the Power-down mode to be enabled.
The rest of pattern combinations will keep the Watchdog
Timer enabled and disable the Power-down mode.
This security key with multiple flags split in two SFRs will
prevent the Watchdog Timer from being terminated
abnormally when the function of the Watchdog Timer is
needed.
In the Idle mode the Watchdog Timer and reset circuitry
remain active.
The time interval between timer reloading and the
occurrence of a reset, depends on the reloaded value.
Table 27 Resolution and the maximum time interval of the WDT
fclk
(MHz)
PRESCALER FACTOR
RESOLUTION
(ms)
MAXIMUM TIME INTERVAL
(s)
10
152
15.56
4.0
12.97
3.3
19.46
5.0
12
16
1997 Dec 12
304
21
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
Port 2 Two alternative functions are provided:
10 INPUT/OUTPUT (I/O)
• High-order address in Programming/Verify mode
for P87C380.
The P83C880 has three 8-bit ports. Ports 0 to 2 are the
same as in the 80C51, with the exception of the additional
functions of Port 1 and Port 2. Port 3 only contains 4 bits.
Port 3 also has alternative functions.
• 8 channels of PWM outputs:
PWM0/P2.0 to P2.7/PWM7. The port type in this
situation is set as open-drain.
All ports are bidirectional. Pins of which the alternative
function is not used may be used as normal bidirectional
I/Os.
Port 3 Two alternative functions are provided:
• Two channels of PWM output:
PWM8/CLAMP/P3.0 and PWM9/PATOUT/P3.1.
The port type in this situation is set as
open-drain. PATOUT and CLAMP functions
always override PWM or port function even if
they are enabled. For the PATOUT (pattern
output) and CLAMP (clamping output)
application, the port type is defined as push-pull.
The use of Port 1, Port 2 and Port 3 pins as an alternative
function is carried out automatically by the P83C880
provided the associated Special Function Register bit is
set HIGH.
The quasi-bidirectional type of port is applied for Port 1,
Port 2 and Port 3. Port 0 is an open-drain I/O port with the
capability to drive LED. However, for any port with an
alternative function, while the alternative function is
performed, the port type will be switched to the appropriate
type against a specific function. The port types:
quasi-bidirectional, pull-up and open-drain are shown in
Figs 7, 8 and 9 respectively.
10.1
• Two pins for the software ADC input: ADC0/P3.2
and ADC1/P3.3. They are analog inputs.
10.2
EMI (Electromagnetic Interference) reduction
In order to reduce EMI (Electromagnetic Interference) the
following design measures have been taken:
The alternative functions for Port 0, Port 1,
Port 2 and Port 3
• Slope control is implemented on all the I/O lines with
alternative functions of the PWM, I2C-bus and DDC
interface. For port pins P1.4 and P1.5, since the
alternative functions VSYNCout and HSYNCout are
incorporated, the driving capability is made as small as
possible to reduce radiation and the slope control
function is disabled to have a sharp output. Rise and fall
time (10% to 90%) for slope control are:
trf(min) < rise/fall time < trf(max).
Refer to Chapter 27 for the detailed figures.
Port 0 Provides the low-order address in
programming/verify mode for the P87C380.
Port 1 Used for a number of special functions:
• 2 I/O pins for I2C-bus interface: SCL/P1.0 and
SDA/P1.1. The port type in this situation is set as
open-drain.
• 2 I/O pins for DDC interface: SCL1/P1.2 and
SDA1/P1.3. The port type in this situation is set
as open-drain.
• Placing the VDD and VSS pins next to each other
• Double bonding of the VDD and VSS pins,
i.e. 2 bondpads for each pin
• 2 I/O pins for the outputs of sync separation:
VSYNCout/P1.4 and HSYNCout/P1.5. The port
type in this situation is set as push-pull.
• Limiting the drive capability of clock drivers and
prechargers
• One pin for the composite sync input of sync on
green mode: CSYNCin/P1.6. There is no pull-up
protection diode for this input pin.
• Applying slew rate controlled output drivers
• Internal decoupling of the supply of the CPU core.
• One pin for the 14-bit PWM output:
PWM10/P1.7. As PWM function, the port type is
open-drain.
1997 Dec 12
P83Cx80; P87C380
22
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
VDD
strong pull-up
handbook, full pagewidth
2 oscillator
periods
p2
p3
p1
I/O PIN
Q
from port latch
n
I1
input data
read port pin
INPUT
BUFFER
MGG025
Fig.7 Standard output with quasi-bidirectional port.
VDD
strong pull-up
handbook, full pagewidth
2 oscillator
periods
p2
'1'
p3
p1
I/O PIN
Q
from port latch
n
I1
input data
read port pin
INPUT
BUFFER
MGG026
Fig.8 Standard output with the pull-up current source.
VDD
strong pull-up
handbook, full pagewidth
2 oscillator
periods
p2
'0'
p1
I/O PIN
Q
from port latch
n
I1
input data
read port pin
INPUT
BUFFER
MGG027
Fig.9 Standard output with the open-drain port.
1997 Dec 12
23
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
The flag bits GF0 and GF1 may be used to determine
whether the interrupt was received during normal
execution or during Idle mode. For example, the
instruction that writes to PCON.0 can also set or clear
both flag bits. When Idle mode is terminated by an
interrupt, the service routine can examine the status of
the flag bits.
11 REDUCED POWER MODES
Two software selectable modes of reduced power
consumption are implemented. These are the Idle mode
and the Power-down mode.
11.1
P83Cx80; P87C380
Power Control Register (PCON)
The Idle mode and Power-down mode are activated by
software via the Power Control Register (SFR PCON).
Its hardware address is 87H. PCON is not bit addressable.
The reset value of PCON is 00H.
• The second way of terminating the idle mode is with an
external hardware reset. Since the oscillator is still
running, the hardware reset is required to be active for
two machine cycles (24 oscillator periods) to complete
the reset operation.
11.2
• The third way of terminating the Idle mode is by an
internal watchdog reset.
Idle mode
Idle mode operation permits the interrupts, I2C-bus
interface, DDC interface, mode detection and timer blocks
T0, T1 and T2 (Watchdog Timer) to function while the CPU
is halted. The following functions are switched off when the
microcontroller enters the Idle mode:
In all cases the microcontroller restarts after 3 machine
cycles.
11.3
• CPU (halted)
In Power-down mode the system clock is halted. The
oscillator is frozen after setting the bit PD in the PCON
register.
• PWM0 to PWM10 (reset, output = HIGH)
• 4-bit ADC (aborted if conversion is in progress)
• DAC0 to DAC3 (output = indeterminate or frozen at the
final value prior to the Idle instruction; decided by
software).
The instruction that sets PCON.1 is the last executed prior
to going into the Power-down mode. Once in Power-down
mode, the oscillator is stopped.The content of the on-chip
RAM and the Special Function Registers are preserved.
Note that Power-down mode can not be entered when the
Watchdog Timer has been enabled.
The following functions remain active during Idle mode;
these functions may generate an interrupt or reset and
thus terminate the Idle mode:
• Timer 0, Timer 1 and Timer 2 (Watchdog Timer)
The Power-down mode can be terminated by an external
reset in the same way as in the 80C51 (but the SFRs are
cleared due to RESET) or in addition by the external
interrupt, INT1.
• The DDC interface
• External interrupt
• Mode detection.
A termination with INT1 does not affect the internal data
memory and the Special Function Registers. This gives
the possibility to exit from Power-down without changing
the port output levels. To terminate the Power-down mode
with an external interrupt, INT1 must be switched to be
level-sensitive and must be enabled. The external interrupt
input signal INT1 must be kept LOW till the oscillator has
restarted and stabilized. The instruction following the one
that put the device into the Power-down mode will be the
first one which will be executed after the wake-up.
The instruction that sets PCON.0 is the last instruction
executed in the normal operating mode before Idle mode
is activated. Once in the Idle mode, the CPU status is
preserved in its entirety: the Stack Pointer, Program
Counter, Program Status Word, Accumulator, RAM and all
other registers maintain their data during Idle mode.
The status of external pins during Idle mode is shown in
Table 28.
There are three ways to terminate the Idle mode:
• Activation of any enabled interrupt X0, T0, X1, T1 or S1
will cause PCON.0 to be cleared by hardware
terminating Idle mode. The interrupt is serviced, and
following return from interrupt instruction RETI, the next
instruction to be executed will be the one which follows
the instruction that wrote a logic 1 to PCON.0.
1997 Dec 12
Power-down mode
24
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
11.4
P83Cx80; P87C380
the DDC interface pins SCL1 and SDA1 respectively. In
Idle mode SCL1 and SDA1 can be active only if DDC1
or DDC2 is enabled; otherwise these pins are in the
high-impedance (High-Z) state.
Status of external pins
• If the HSYNCout, VSYNCout, PATOUT or CLAMP output
is selected (for selection see description in Tables 8
and 18) in Idle or Power-down mode, since sync
separation is still alive in Idle mode, HSYNCout,
VSYNCout, PATOUT or CLAMP output will be operating
as normal. In Power-down mode: HSYNCout, VSYNCout,
PATOUT or CLAMP output are pulled HIGH.
• If bit PWME.n (SFR PWME1/PWME2) is set, the
function of P1.7, P2.n, P3.0 and P3.1 will be switched to
the PWM output function. However, in both Idle and
Power-down modes, the output of those PWM pins are
pulled HIGH.
• In Idle or Power-down mode, if bit DDCE (SFR DFCON)
is set, the function of P1.2 and P1.3 will be switched to
Table 28 Status of external pins during Idle and Power-down modes
MODE
MEMORY
PORT0
TO
PORT 3
HSYNC;
VSYNC;
CLAMP;
PATOUT
SCL
AND
SDA
SCL1
AND
SDA1
PWM0
TO
PWM10
DAC0
TO
DAC3
Idle
internal
data
operative
High-Z
operative
HIGH
unknown
Power-down
internal
data
HIGH
High-Z
High-Z
HIGH
unknown
1997 Dec 12
25
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
XTAL1 is the high gain amplifier input, and XTAL2 is the
output (see Fig.10a). To drive the P83C880 externally,
XTAL1 is driven from an external source and XTAL2 left
open-circuit (see Fig.10b).
12 OSCILLATOR
The oscillator circuit of the P83C880 is a single-stage
inverting amplifier in a Pierce oscillator configuration. The
circuitry between XTAL1 and XTAL2 is basically an
inverter biased to the transfer point. Either a crystal or
ceramic resonator can be used as the feedback element to
complete the oscillator circuit. Both are operated in parallel
resonance.
handbook, halfpage
handbook, halfpage
XTAL1
XTAL1
XTAL2
XTAL2
n.c.
MBE311
a.
external clock
(not TTL compatible)
b.
Crystal oscillator; C = 20 pF.
handbook, halfpage
XTAL1
XTAL2
external clock
(not TTL compatible)
c.
MLC930 - 1
External clock drive for P87C380.
Fig.10 Oscillator configurations.
1997 Dec 12
26
External clock drive.
MBE312
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
Figure 11 illustrates the reset mechanism. Each reset
source will activate an internal reset signal RSTOUT. The
CPU responds by executing an internal reset and puts the
internal registers in a defined state as shown in Table 29.
13 RESET
There are three ways to invoke a reset and initialize the
P83C880:
• Via the external RESET pin
• Via the built-in Power-on-reset circuitry
• Via the Watchdog Timer overflow.
Table 29 Reset values of the Special Function Registers
X = Undefined. The internal RAM is not affected by reset.
ADDRESS
REGISTER
CONTENT
ADDRESS
REGISTER
CONTENT
80H
P0
1111 1111
CDH
PWM4
0000 0000
81H
SP
0000 0111
CEH
PWM5
0000 0000
82H
DPL
0000 0000
CFH
PWM6
0000 0000
83H
DPH
0000 0000
D0H
PSW
0000 0000
87H
PCON
0000 0000
D8H
S1CON
0000 0000
88H
TCON
0000 0000
D9H
S1STA
1111 000
89H
TMOD
0000 0000
DAH
S1DAT
0000 0000
8AH
TL0
0000 0000
DBH
S1ADR
0000 0000
8BH
TL1
0000 0000
E0H
ACC
0000 0000
8CH
TH0
0000 0000
E8H
PWME2
0000 0000
8DH
TH1
0000 0000
E9H
DAC0
0000 0000
90H
P1
1111 1111
EAH
DAC1
0000 0000
9CH
RAMBUF
0000 0000
EBH
DAC2
0000 0000
9DH
DDCCON
X00X 0000
ECH
DAC3
0000 0000
9EH
DDCADR
0000 0000
EDH
PWM7
0000 0000
9FH
DDCDAT
0000 0000
EEH
PWM8
0000 0000
A0H
P2
1111 1111
EFH
PWM9
0000 0000
A8H
IEN0
0X0X 0000
F0H
B
0000 0000
B0H
P3
XXXX 1111
F6H
HFP
0110 0000
B8H
IP0
XX0X 0000
F7H
HFPOPW
0000 0101
C0H
DFCON
1000 0000
F8H
MDCST
1X00 0000
C1H
ADCDAT
XX00 0000
F9H
VFP
0100 0000
C6H
PWM10H
0000 0000
FAH
VFPOPW
XX00 0101
C7H
PWM10L
1000 0000
FBH
PULCNT
0000 0000
C8H
PWME1
0000 0000
FCH
HFHIGH
0000 0000
VFHIGH
0000 0000
C9H
PWM0
0000 0000
FDH
CAH
PWM1
0000 0000
FEH
VFLHFL
0000 0000
CBH
PWM2
0000 0000
FFH
T2
0000 0000
CCH
PWM3
0000 0000
1997 Dec 12
27
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
handbook, full pagewidth
P83Cx80; P87C380
VDD
SCHMITT
TRIGGER
10 µF
RSTOUT
RESET
8 kΩ
RESET
CIRCUITRY
RRESET
overflow timer T2
on-chip circuit
Power-on-reset
POC
MGG022
Fig.11 On-chip reset configuration.
13.1
In the case of supply voltage fall, after the trip level Vt is
reached, the power-on reset signal will follow the
waveform of the supply voltage for time interval Tp.
External reset
Pin RESET is connected to a Schmitt trigger for noise
reduction (see Fig.11). A reset is accomplished by holding
the RESET pin HIGH for at least 16 machine cycles (192
system clocks) while the oscillator is running.
The time interval Tp guarantees that a complete power-on
reset pulse can trigger the internal reset signal. However,
to ensure that the oscillator is stable before the controller
starts, the clock signals are gated away from the CPU for
a further 2048 oscillator cycles.
An automatic reset can be obtained by switching on VDD,
if the RESET pin is connected to VDD via a capacitor and
a resistor as illustrated in Fig.11. The VDD rise time must
not exceed 10 ms and the capacitor should be at least
10 µF. The decrease of the RESET pin voltage depends
on the capacitor and the external resistor RRESET. The
voltage must remain above the lower threshold for at least
the oscillator start-up time plus 2 machine cycles.
13.2
The values of Vt, Tp and a process tolerance of ± ∆Vt can
be found in Chapter 25; currently Vt = 3.9 V, Tp = 10 µs
and ∆Vt = 0.3 V.
13.3
The length of the output pulse from T2 is 3 machine cycles.
A pulse of such short duration is necessary in order to
recover from a processor or system fault as fast as
possible.
Power-on-reset
An on-chip Power-on-reset circuit that detects the supply
voltage rise or fall and accordingly generates a power-on
reset pulse (see Fig.12).
In the case of supply voltage rise, the power-on reset
signal will follow the supply voltage rise; after reaching the
trip level Vt the power-on reset signal will maintain the
same behaviour, and returns to a LOW state after a time
interval Tp.
1997 Dec 12
T2 (Watchdog Timer Data Register) overflow
28
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
∆Vt
handbook, full pagewidth
supply
voltage
Vt
Power-on-reset
oscillator
CPU
running
2048 clocks
2048 clocks
Tp
start-up
Tp
Fig.12 Power-on reset switching level.
1997 Dec 12
29
MGG023
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
The polarity of the PWM outputs is programmable and is
selected by the P8LVL bit in SFR DFCON (address C0H);
see Table 4.
14 ANALOG CONTROL (DC)
The P83C880 has eleven Pulse Width Modulated (PWM)
outputs for analog control purposes e.g. brightness,
contrast, E-W, R (or G or B) gain control etc. Each PWM
output generates a pulse pattern with a programmable
duty cycle.
The duty cycle of outputs PWM0 to PWM9 is dependent
on the programmable contents of the data latches: SFRs
PWM0 to PWM9. As the clock frequency of each PWM
circuit is 1⁄4fclk, the pulse width of the pulse generated can
The eleven PWM outputs comprise:
• 10 PWM outputs with 8-bit resolution (PWM0 to PWM9);
described in Section 14.1.
4 × ( PWMn )
be calculated as: Pulse width = ---------------------------------f clk
• 1 PWM output with 14-bit resolution (PWM10);
described in Section 14.2.
Where (PWMn) is the decimal value held in the relevant
data latch.
A typical PWM output application is described in
Section 14.3.
The maximum repetition frequency of the 8-bit PWM
f clk
outputs is: f PWM = -----------1024
14.1
8-bit PWM outputs (PWM0 to PWM9)
The block diagram for the 8-bit PWM outputs is shown in
Fig.13.
PWM outputs PWM0 to PWM9 share the same pins as
port lines P2.0 to P2.7, P3.0 and P3.1 respectively.
Selection of the pin function as either a PWM output or a
port line is achieved using the appropriate PWMnE bit in
SFRs, PWME1 (address C8H) and PWME2 (address
E8H); see Table 4.
internal data bus
handbook, full pagewidth
fclk
P8LVL
8-BIT PWM DATA LATCH
P2.x/P3.x data I/O
4
PWMnE
8-BIT DAC PWM
CONTROLLER
Q
P2.x/P3.x/PWMn
Q
MGG042
Fig.13 Block diagram for 8-bit PWMs.
1997 Dec 12
30
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
handbook, ffull
clkpagewidth
4
256
1
2
3
m+1
m
m+2
256
1
00
01
m
255
decimal value PWM data latch
MGG043
Fig.14 PWM0 to PWM9 output patterns.
14.2
The outputs OUT1 and OUT2 of the coarse and fine pulse
controllers are then ‘ORed’ in the mixer to give the PWM10
output. The polarity of the PWM10 output is programmable
and is selected by the P14LVL bit in SFR DFCON (address
C0H); see Section 7.3.2.
14-bit PWM output (PWM10)
PWM10 shares the same pin as port line P1.7. Selection
of the pin function as either a PWM output or as a port line
is achieved using the PWME2.0 bit in SFR PWME2
(address E8H); see Table 4.
As the 14-bit counter is clocked by 1⁄4fclk, the repetition
times of the coarse and fine pulse controllers may be
calculated as shown below.
The block diagram for the 14-bit PWM output is shown in
Fig.15 and comprises:
• Two 7-bit latches; SFRs PWM10H and PWM10L
• 14-bit data latch (PWMREG)
4
Coarse controller repetition time: t sub = 128 × ------f clk
• 14-bit counter
• Coarse pulse controller
4
Fine controller repetition time: t r = 128 × 128 × ------f clk
• Fine pulse controller
• Mixer.
Figure 16 shows typical PWM10 outputs, with coarse
adjustment only, for different values held in PWM10H,
when P14LVL = 1. Figure 17 shows typical PWM10
outputs when P14LVL = 1, with coarse and fine
adjustment, after the coarse and fine pulse controller
outputs have been ‘ORed’ by the mixer.
Data is loaded into the 14-bit data latch (PWMREG) from
the two 7-bit data latches (PWM10H and PWM10L) when
PWM10H is written to. The upper seven bits of PWMREG
are used by the coarse pulse controller and determine the
coarse pulse width; the lower seven bits are used by the
fine pulse controller and determine in which subperiods
fine pulses will be added.
1997 Dec 12
When P14LVL = 1, the PWM10 output is inverted.
31
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
internal data bus
handbook, full pagewidth
‘MOVE instruction’
PWM10L
PWM10H
7
DATA LOAD
TIMING PULSE
‘MOV instruction’
7
LOAD
PWMREG
7
7
FINE PULSE
GENERATOR
COARSE 7-BIT
PWM
OUT1
OUT2
MIXER
Q
polarity
control bit
Q
PWM10 output
P14LVL
Q14 to 8
Q7 to 1
14-BIT COUNTER
fclk
4
MGG044
Fig.15 14-bit PWM block diagram.
1997 Dec 12
32
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
14.2.1
P83Cx80; P87C380
For example, if PWM10L = 000 0101 then this is a
combination of:
COARSE ADJUSTMENT
An active HIGH pulse is generated in every subperiod; the
pulse width being determined by the contents of PWM10H.
The coarse output (OUT1) is HIGH at the start of each
subperiod and will remain HIGH until the time
[4/fclk × (128 − PWM10H)] has elapsed. The output will
then go LOW and remain LOW until the start of the next
subperiod. The coarse pulse width may be calculated as:
• PWM10L = 000 0001: subperiod 64
• PWM10L = 000 0100: subperiods 16, 48, 80 and 112.
Pulses will be added in subperiods 16, 48, 64, 80 and 112.
This example is illustrated in Fig.18.
When PWM10L holds 000 0000 fine adjustment is
inhibited and the PWM10 output is determined only by the
contents of PWM10H.
4
Pulse duration = ( PWM10H ) × ------f clk
Table 30 Additional pulse distribution
14.2.2
FINE ADJUSTMENT
PWM10L
Fine adjustment is achieved by generating an additional
pulse in specific subperiods. The pulse is added at the
start of the selected subperiod and has a pulse width of
4/fclk. The contents of PWM10L determine in which
subperiods a fine pulse will be added. It is the logic 0 state
of the value held in PWM10L that actually selects the
subperiods. When more than one bit is a logic 1 then the
subperiods selected will be a combination of those
subperiods specified in Table 30.
ADDITIONAL PULSE IN SUBPERIOD
000 0001
64
000 0010
32 and 96
000 0100
16, 48, 80 and 112
000 1000
8, 24, 40, 56, 72, 88, 104 and 120
001 0000
4, 12, 20, 28, 36, 44, 52...116 and 124
010 0000
2, 6, 10, 14, 18, 22, 26, 30...122 and 126
100 0000
1, 3, 5, 7, 9, 11, 13, 15, 17...125 and 127
handbook,fclk
full pagewidth
4
127
0
1
2
128 − (m + 1)
00
128 − (m − 1)
128 − m
127
0
1
01
m
127
MGG045
decimal value PWM7H data latch
Fig.16 PWM10 output patterns: Coarse adjustment only.
1997 Dec 12
33
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync
P83Cx80; P87C380
fclk
handbook,
full pagewidth
4
127
0
1
2
128 − (m + 1)
128 − (m − 1)
128 − m
127
0
1
00
01
m
127
MGG046
decimal value PWM10H data latch
Fig.17 PWM10 output patterns: Coarse and fine adjustment (PWM10L = 000 0000B).
tr
handbook, full pagewidth
tsub0
tsub16
tsub32
tsub48
tsub64
tsub80
tsub96
tsub112
tsub127
000 0001
000 0100
000 0101
MGG047
PWM10L
Fig.18 Fine adjustment output (OUT2).
1997 Dec 12
34
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
14.3
P83Cx80; P87C380
A typical PWM output application
A typical PWM application is shown in Fig.19. The buffer is
optionally used to reduce the influence from supply/ground
bouncing to another circuit. R1 and C1 form the integration
network, the time constant of which should be equal to or
greater than 5 times the repetition period of the PWM
output pattern. In order to smooth a changing PWM output
a high value of C1 should be chosen. The value of C1 will
normally be in the range 1 to 10 µF. The potential divider
chain formed by R2 and R3 is used only when the output
voltage is to be offset. The output voltages for this
application are calculated using Equations (1) and (2).
R3 × V DD
(1)
V max = -----------------------------------R1 × R2
R3 + ---------------------R1 + R2
V min
R1 × R3
---------------------- × V DD
R1 + R3
= --------------------------------------R1 × R3
R2 + ---------------------R1 + R3
R2
R1
analog
output
PWMn
DEVICE
TYPE NR. (1)
C1
R3
VSS
MGG048
(2)
The loop from the PWM pin through R1 and C1 to VSS will
radiate high frequency energy pulses. In order to limit the
effect of this unwanted radiation source, the loop should
be kept short and a high value of R1 selected. The value
of R1 will normally be in the range 3.3 to 100 kΩ. It is good
practice to avoid sharing VSS (pin 12) with the return leads
of other sensitive signals.
1997 Dec 12
supply
voltage
andbook, halfpage
(1) P83Cx80; P87C380
Fig.19 Typical PWM output circuit.
35
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
Table 32 Selection of ADC channel
15 ANALOG-TO-DIGITAL CONVERTER (ADC)
The ADC inputs ADC0 and ADC1 share the same pins as
port lines P3.2 and P3.3 respectively. Selection of the pin
function as either an ADC input or as a port line is achieved
using bit ADCE in SFR DFCON (address C0H). When
ADCE = 1, the ADC function is enabled; see Section 7.3.2,
Table 8.
DACHL
CHANNEL SELECTED
0
ADC0
1
ADC1
15.1
Conversion algorithm
The two channel ADC comprises a 4-bit Digital-to-Analog
Converter (DAC); a comparator; an analog channel
selector and control circuitry. As the digital input to the 4-bit
DAC is loaded by software (a subroutine in the program),
it is known as a software ADC. The block diagram is shown
in Fig.20.
There are many algorithms available to achieve the ADC
conversion. The algorithm described below and shown in
Fig.21 uses an iteration process.
The 4-bit DAC analog output voltage (Vref) is determined
by the decimal value of the data held in bits DAC0 to DAC3
(DAC value) of SFR ADCDAT (address C1H). Vref is
2. Set the digital input to the DAC to 1000. The digital
input to the DAC is selected using bits DAC3 to DAC0
(SFR ADCDAT).
V DD
calculated as: V ref = ---------- × ( DAC value + 1 )
16
3. Determine the result of the compare operation. This is
achieved by reading the COMP bit in SFR ADCDAT
using the instruction ‘MOV A, ADCDAT’. If COMP = 1;
the analog input voltage is higher than the reference
voltage (Vref). If COMP = 0; the analog input voltage is
lower than the reference voltage (Vref).
1. Select ADCn channel for conversion. Channel
selection is achieved using bit DACHL, SFR ADCDAT
(address C1H).
Table 31 lists the Vref values as function of DAC3 to DAC0.
When the analog input voltage is higher than Vref, the
COMP bit in SFR ADCDAT (address C1H) will be HIGH.
The channel selector, consisting of two analog switches, is
controlled by bit DACHL in SFR ADCDAT; see Table 32.
4. If COMP = 1; then the analog input voltage is higher
than the reference voltage (Vref) and therefore the
digital input to the DAC needs to be increased. Set the
input to the DAC to 1100.
Table 31 Selection of Vref
DAC3
DAC2
DAC1
DAC0
0
0
0
0
1⁄
16
× VDD
0
0
0
1
2⁄
16
× VDD
16
× VDD
0
0
1
0
3⁄
0
0
1
1
4⁄
16
× VDD
16
× VDD
0
1
0
0
5⁄
0
1
0
1
6⁄
16
× VDD
0
1
1
0
7⁄
16
× VDD
16
× VDD
0
1
1
1
8⁄
1
0
0
0
9⁄
1
0
0
1
1
0
1
0
1
0
1
1
1
1
0
0
1
1
0
1
1
1
1
0
16 × VDD
10⁄ × V
16
DD
11⁄ × V
16
DD
12⁄ × V
16
DD
13⁄ × V
16
DD
14⁄ × V
16
DD
15⁄ × V
16
DD
1
1
1
1
VDD
1997 Dec 12
5. If COMP = 0; then the analog input voltage is lower
than the reference voltage (Vref) and therefore the
digital input to the DAC needs to be decreased. Set the
input to the DAC to 0100.
Vref (V)
6. Determine the result of the compare operation by
reading the COMP bit in SFR ADCDAT.
7. For the DAC = 1100 case.
If COMP = 1; then the analog input voltage is still
greater than Vref and therefore the digital input to the
DAC needs to be increased again. Set the input to the
DAC to 1110.
If COMP = 0; then the analog input voltage is now less
than Vref and therefore the digital input to the DAC
needs to be decreased. Set the input to the DAC to
1010.
36
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
8. For the DAC = 0100 case.
P83Cx80; P87C380
The complete process is shown in Fig.21. Each time
the DAC input is changed the number of values which
the analog input can take is reduced by half. In this
manner the actual analog value is honed into. The
value of the analog input (VA) is determined by the
formulae:
V DD
V A = ---------- × ( DAC value + 1 )
16
If COMP = 1; then the analog input voltage is now
greater than Vref and therefore the digital input to the
DAC needs to be increased. Set the input to the DAC
to 0110.
If COMP = 0; then the analog input voltage is still lower
than Vref and therefore the digital input to the DAC
needs to be decreased again. Set the input to the DAC
to 0010.
As the conversion time of each compare operation is
greater than 6 µs but less than 9 µs; a NOP instruction is
recommended to be used in between the instructions that
select Vref; the ADC channel and read the COMP bit.
9. The operations detailed in 5, 6 and 7 above are
repeated and each time the digital input to the DAC is
changed accordingly; as dictated by the state of the
COMP bit.
handbook, full pagewidth
internal bus
PORT INTERFACE
EN0
EN1
P3.3/ADC1
ADC
CHANNEL
SELECTOR
Vref
P3.2/ADC0
channel selection
COMP bit
+
COMPARATOR
−
MOV A, ADCDAT
instruction
to read COMP bit
EN
ENABLE
SELECTOR
DACHL
4-BIT DAC
ADCE
DAC3
ADC enable selection
DAC2
DAC1
DAC value selection
Fig.20 Block diagram of the ADC.
1997 Dec 12
37
DAC0
MGG049
1997 Dec 12
38
1110
1101
T
−0001
F
T
1010
F
1001
T
F
−0001
COMP = 1
F
1000
Value = 1000
COMP = 1
F
−0001
0110
0101
F
T
COMP = 1
−0010
0010
F
F
−0001
F
MBK518
0000
COMP = 1
Value = 0000
0001
T
COMP = 1
Value = 0001
Value = 0010
0011
T
F
+0001
COMP = 1
0100
COMP = 1
T
F
COMP = 1
F
COMP = 1
T
Value = 0100
T
Value =0101
+0010
−0100
Value = 0011
Value = 0110
+0001
0111
T
COMP = 1
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
Fig.21 Example of converting algorithm for software ADC.
COMP = 1
−0010
Value = 1001
Value = 1010
1011
T
F
+0001
COMP = 1
1100
COMP = 1
F
F
COMP = 1
1111
T
COMP = 1
Value = 1100
T
T
Value = 1110
+0001
Value = 1101
+0010
Value = 1011
T
handbook, full pagewidth
+0100
Value = 0111
Philips Semiconductors
Product specification
P83Cx80; P87C380
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
The range of the output voltage is approximately 0 to 5 V.
However, to fulfil some special requirement for current
driving capability, a very minor reduction (0.2 to 0.4 V) of
the output voltage range is acceptable.
16 DIGITAL-TO-ANALOG CONVERTER (DAC)
Four channels of linear voltage outputs mainly for the
horizontal and vertical position control are provided from
four sets of the Digital-to-Analog Converter (DAC).
The DAC outputs are protected against short-circuits to
VDDA and VSSA. To avoid the possibility of oscillation,
capacitive loading at the DAC outputs should not exceed
10 pF. In reduced power modes like Idle mode and
Power-down mode, the operation of the DACs can be
disabled to save the power consumption. In that case, the
outputs of the DACs are indeterminate.
The DACs are well tuned to meet the following specific
system requirements of the monitor.
• For a 21'' monitor, the shift per step by changing the data
of the DAC is expected to be 0.5 mm. Accordingly, the
DAC with 8-bit resolution is required.
• To avoid visible position shift due to environmental
temperature change, the drift of output level of the DAC
is less than 1.5 mV/°C.
Figure 20 illustrates the block diagram of the DAC.
• To eliminate the visible jitter, the maximum tolerable
ripple for the output voltage of the DAC is less than
2 mV.
16.1
8-bit Data Registers for the DAC outputs
(DACn; n = 0 to 3)
The DACs are individually programmed using an 8-bit
word to select an output from one of 256 voltage steps. For
VDDA = 5 V, the maximum output voltage of all DACs is 5 V
and the resolution is approximately 17.6 mV (5 V/256). At
power-on all DAC outputs are set to their lowest value:
00H (i.e. 0 V). The relevant SFRs for the DACs are
described in Table 33 and 34.
Each DAC comprises an 8-bit data latch, a voltage scaling
mechanism and an output driver.
A precise current reference is provided internally to serve
4 sets of DACs. The voltage sources with values weighted
by 20 up to 27 are switched according to the data input so
that the sum of the selected voltages gives the required
analog voltage from the output driver.
Table 33 8-bit Data Registers for the DAC outputs (address E9H to ECH)
7
6
5
4
3
2
1
0
DACn.7
DACn.6
DACn.5
DACn.4
DACn.3
DACn.2
DACn.1
DACn.0
Table 34 Description of DACn bits
BIT
SYMBOL
7 to 0
DACn.7 to DACn.0
1997 Dec 12
DESCRIPTION
8-bit data for the DAC; channel n (n = 0 to 3).
39
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
handbook, full pagewidth
P83Cx80; P87C380
internal bus
REFERENCE
VOLTAGE/CURRENT
GENERATOR
8
DATA LATCH
(SFR ADDRESS E9H)
DATA LATCH
(SFR ADDRESS EAH)
DATA LATCH
(SFR ADDRESS EBH)
DATA LATCH
(SFR ADDRESS ECH)
DAC0
DAC1
DAC2
DAC3
MGG050
DAC0
DAC1
DAC2
Fig.22 Block diagram of the DAC.
1997 Dec 12
40
DAC3
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83C880 is compliant to DDC1, DDC2B, DDC2B+ and
DDC2AB (ACCESS.bus). They also conform to the
detection sequence defined by VESA and ACCESS.bus
Industry Group and identify the protocol which they are
communicating with.
17 DISPLAY DATA CHANNEL (DDC) INTERFACE
The monitor typically includes a number of user controls to
set picture size, position, colour balance, brightness and
contrast. Furthermore, to optimize some internal setting for
different display modes, the timing characteristics should
be acquired by the control side. For factory alignment, it is
preferable to store the entire information in a non-volatile
memory to facilitate production automation. Normally,
monitors provide hardware control panels or a keypad to
perform this control. However, it is now popular for these
controls to go to the PC host. Therefore the
communication between monitor and host becomes an
issue. DDC1, DDC2B, DDC2B+ and DDC2AB
(ACCESS.bus) emerge as a standard for monitor
interface.
17.1
P83Cx80; P87C380
A transmitter clocked by the incoming VSYNC is dedicated
for DDC1 operation. An I2C-bus interface hardware logic
forms the kernel of DDC2B and DDC2AB. An address
pointer, DDCADR (address 9EH), with post increment
capability is employed to serve DDC1, DDC2B, DDC2B+
and DDC2AB modes.
The conceptual block diagram is illustrated in Fig.23.
Special Function Registers related to the DDC interface
Table 35 SFRs related to the DDC interface
ADDRESS
SFR
REMARKS
9CH
RAMBUF
See Section 7.3.1.
9DH
DDCCON
9EH
DDCADR
DDCCON, DDCADR and DDCDAT are mainly created for the DDC1 protocol; they are
explained in Sections 17.1.1 to 17.1.3.
9FH
DDCDAT
D8H
S1CON
D9H
S1STA
DAH
S1DAT
DBH
S1ADR
17.1.1
One extra I2C-bus interface is used to serve DDC2B, DDC2B+ and DDC2AB. Therefore
S1CON, S1STA, S1DAT and S1ADR are just the copies of the corresponding registers
in the general I2C-bus interface. Their usage is exactly the same.
DDC MODE STATUS AND DDC1 CONTROL REGISTER (DDCCON)
Table 36 DDC Mode Status and DDC1 Control Register (address 9DH)
7
6
5
4
3
2
1
0
−
EX_DAT
SWENB
−
DDC1_int
DDC1enable
SWH_int
M0
1997 Dec 12
41
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
Table 37 Description of DDCCON bits
BIT
SYMBOL
7
−
6
EX_DAT
This bit defines the size of the EDID data. It is related to the function of the post
increment of the address pointer, DDCADR. When the upper limit is reached, the
address pointer will wrap around to 00H. If EX_DAT = 1, the data size is 256 bytes.
If EX_DAT = 0, the data size is 128 bytes; the addressing range for the EDID data
buffer is mapped from 0 to 127, the rest (128 to 255) can still be used by the system.
5
SWENB
This bit indicates if the software/CPU is needed to take care of the operation of DDC1
protocol. If SWENB = 1, in DDC1 protocol, the CPU is interrupted during the period of
the 9th transmitting bit so that the software service routine can update the hold
register of the transmitter by moving new data from the appropriate area (it is not
necessary to be the RAM buffer). This transferring must be done within 40 µs.
If SWENB = 0, the hold register of the transmitter will be automatically updated from
the RAM buffer without the intervention of the CPU.
4
−
3
DDC1_int(1)
2
DESCRIPTION
Reserved.
Reserved.
Interrupt request bit (002BH is assigned as the interrupt vector address). This bit is only
valid in DDC1 protocol while software handling is enabled (SWENB = 1). This bit is set
by hardware and should be cleared by software in an interrupt service routine. If DDC1
is fully under the hardware control (SWENB = 0), this bit can be ignored.
If DDC1_int = 1, interrupt request is pending. If DDC1_int = 0, there are no interrupt
request.
DDC1enable(1) DDC1 enable control bit. If DDC1enable = 1, DDC1 is enabled. If DDC1enable = 0,
DDC1 is disabled (the activity on VCLK is ignored).
1
SWH_int(1)
0
M0(1)
Interrupt request bit (002BH is assigned as the interrupt vector address). This bit is
used to indicate that DDC interface switches from DDC1 to DDC2 (i.e. the
HIGH-to-LOW transition is observed on pin SCL1). This bit should be cleared by
software in an interrupt service routine. If SWH_int = 1, interrupt request is pending.
If SWH_int = 0, there is no interrupt request.
DDC mode indication bit. If M0 = 0, DDC1 is set; if M0 = 1, DDC2 is set.
Note
1. These bits are R/W.
1997 Dec 12
42
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
17.1.2
P83Cx80; P87C380
ADDRESS POINTER FOR DDC INTERFACE REGISTER (DDCADR)
The bits of this register are all R/W.
Table 38 Address Pointer for DDC Interface Register (address 9EH)
7
6
5
4
3
2
1
0
DDCADR.7
DDCADR.6
DDCADR.5
DDCADR.4
DDCADR.3
DDCADR.2
DDCADR.1
DDCADR.0
Table 39 Description of DDCADR bits
BIT
SYMBOL
DESCRIPTION
7 to 0
DDCADR.7 to DDCADR.0
Address pointer with the capability of post increment. After each access
to RAMBUF register (either by software or by hardware DDC1 interface),
the content of this register will be increased by one. It is available both in
DDC1, DDC2 (DDC2B, DDC2B+ and DDC2AB) and system operation.
17.1.3
DDC1 DATA TRANSMISSION REGISTER (DDCDAT)
Table 40 DDC1 Data Transmission Register (address 9FH)
7
6
5
4
3
2
1
0
DDCDAT.7
DDCDAT.6
DDCDAT.5
DDCDAT.4
DDCDAT.3
DDCDAT.2
DDCDAT.1
DDCDAT.0
Table 41 Description of DDCDAT bits
BIT
7 to 0
1997 Dec 12
SYMBOL
DDCDAT.7 to DDCDAT.0
DESCRIPTION
Data byte to be transmitted in DDC1 protocol.
43
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
handbook, full pagewidth
7
1
SIO2
0
MONITOR ADDRESS
S1ADR(DBH)
SDA1
SHIFT REGISTER
S1DAT(DAH)
ARBITRATION LOGIC
SCL1
BUS CLOCK GENERATOR
SI
AA CR1 CR0
DDC2B/DDC2AB/DDC2B+
INTERFACE
DDC1/DDC2
DETECTION
SC4 SC3 SC2 SC1 SC0
0
0
0
S1STA(D9H)
INTERNAL BUS
CR2 ENS STA STO
S1CON(D8H)
RAMBUF(9CH)
RAMBUF
AUX-RAM
BUFFER
DDC1 HOLD REGISTER
DDCDAT(9FH)
DDC1 TRANSMITTER
ADDRESS POINTER
VCLK
DDCADR(9EH)
INITIALIZATION SYNCHRONIZATION
−
EX_DAT
SWENB
−
DDC1_int
DDC1
enable
SWH_int
M0
(from S1CON)
SI
DDCCON(9DH)
INT
(interrupt vector 002BH)
MGG030
Fig.23 DDC interface block diagram.
1997 Dec 12
44
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
17.2
Accordingly, the interrupt will be invoked by setting flag
SWH_int (DDCCON.1) as HIGH (this flag must be cleared
by the interrupt service routine). This procedure will cause
a transmission error. However, both the display and the
host shall have error detection and a method to recover
from the temporary transmission errors.
Host type detection
The detection procedure conforms to the sequences
proposed by “VESA Monitor Display Data Channel (DDC)
specification”. The monitor needs to determine the type of
host system:
• DDC1 or OLD type host
Figure 24 illustrates the concept and interaction between
the monitor and the host. After power-on, the DDC1enable
bit (DDCCON.2) is set by software, setting the monitor as
a DDC1 device. Therefore, the Mode flag M0, is set as
logic 0. Following VSYNC as clock, the monitor (i.e.
P83C880) will transmit EDID data stream to the host.
However, if DDC2 clock (SCL clock) is present, the
monitor will be switched to DDC2B device with the Mode
flags setting as logic 1. Software will determine whether it
is a DDC2B, DDC2B+, or DDC2AB protocol.
• DDC2B host (host is master, monitor is always slave)
• DDC2B+/DDC2AB (ACCESS.bus) host.
The sequence of detection is described in the flow chart
illustrated in Fig.24.
The monitor where P83C880 resides is always both DDC1
and DDC2 compatible with DDC2 having the higher
priority. The display (i.e. P83C880) shall start transmitting
DDC1 signals whenever it is switched on and VSYNC is
applied to it from the host for the first time. The display
shall switch to DDC2 within 3 system clocks as soon as it
sees a HIGH-to-LOW transition on the clock line (SCL),
indicating that there are both DDC2 devices connected to
the bus. Under that condition, the Mode flag M0 will be
changed from the default setting logic 0 to logic 1.
1997 Dec 12
P83Cx80; P87C380
45
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
handbook, full pagewidth
MONITOR POWER-ON
COMMUNICATION IS IDLE
IS VSYNC
PRESENT?
NO
EDID SENT
CONTINUOUSLY USING
VSYNC AS CLOCK
IS DDC2 CLOCK
PRESENT?
NO
YES
STOP SENDING OF EDID
SWITCH TO DDC2
COMMUNICATION MODE
DDC2 COMMUNICATION
IS IDLE. MONITOR IS
WAITING FOR A COMMAND
(1)
HAS A
COMMAND BEEN
RECEIVED?
NO
YES
NO
IS
DDC2B+/DDCAB2
COMMAND
DETECTED?
YES
NO
IS
MONITOR
DDC2B+/DDCAB2
CAPABLE?
IS
COMMAND DDC2B
COMMAND?
YES
RESPOND TO DDC2B
COMMAND
NO
YES
RESPOND TO DDC2B+/DDCAB2
COMMAND
MGG031
(1) Once the monitor switches from DDC1 mode to DDC2 mode it will
remain in DDC2 mode for the duration of that power-on period.
Fig.24 Host type detection.
1997 Dec 12
46
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
17.3
of the system ROM) or from the RAM buffer. In the latter
case, the address pointer DDCADR will provide the benefit
of the post increment for the service routine to read/write
the DDC1 EDID data area. This action must be finished
within 40 µs (40 machine cycles in 12 MHz system clock).
DDC1_int flag must be cleared by software before it
returns from service routine. On the rising edge of the 10th
clock cycle, the device will output the first valid data bit
which should be the most significant bit of a byte.
DDC1 protocol
The DDC1 is a primitive interface, but adopted by many
monitor models and PC hosts. It is a point-to-point
interface. The monitor is always set to ‘Transmit only’
mode. In the initialization phase, 9 clock cycles on the
VCLK pin will be given for the internal synchronization.
During this period, the SDA pin will be kept in the
high-impedance state. By default, bit ‘DDC1enable’ is
reset as logic 0. It is advised to move the EDID data to the
RAM buffer before enabling DDC1. To activate the DDC1
interface, DDC1enable flag is set to logic 1 and it is taken
as granted that Mode flag M0 is set at logic 0. If SWENB is
kept at the default value logic 0, the RAM buffer will be tied
to the DDC1 protocol. The allocated size from the RAM
buffer is decided by the flag EX_DAT. If EX_DAT is LOW,
only 128 bytes are reserved to store DDC1 EDID data. The
upper part (locations 128 to 255) is still available to the
system. If EX_DAT is HIGH, the entire 256 bytes of the
RAM buffer are dedicated to the usage of DDC1 operation.
The following data is also transmitted on the SDA pin in
8 bits per byte format. Each byte is followed by a 9th clock
pulse during which time SDA is left high-impedance and
either the hardware mechanism (SWENB = 0) or the
service routine (SWENB = 1) will update the hold register.
The data bit is output on the rising edge of VCLK, the most
significant bit first. The address pointer is initialized at 00H.
After writing a data byte to the hold register through
hardware or software, it will be incremented by one
automatically. If the address reaches 127 (EX_DAT = 0) or
255 (EX_DAT = 1) the address pointer will wrap around to
the first location: 00H. Nevertheless, it is possible for CPU
(in software mode, i.e. SWENB = 1) to write any desired
address to the address pointer to proceed random access.
The transaction in DDC1 protocol is shown in Fig.25.
The hardware mechanism will automatically move new
data from the defined RAM buffer to the hold register of the
transmitter with the aid of the address pointer DDCADR.
Within the range of DDC1 RAM buffer, the function of the
post increment is executed. If the upper limit is reached,
the address pointer DDCADR will wrap around to 00H.
However, if EX_DAT = LOW, the lower part is occupied by
the DDC1 operation and the upper part is still free to the
system. Nevertheless, the effect of the post increment just
applies to the part related to the DDC1 operation. In other
words, the system program is still able to address the
locations from 128 to 255 in the RAM buffer through the
MOVX command but without the facility of the post
increment; e.g. in case EX_DAT = LOW and
SWENB = LOW, the system program might read one data
byte from address 200 of the RAM buffer by the following
procedure:
If DDC1 hardware mode is used, the following DDC1
operation steps are recommended:
1. Reset DDC1enable (by default DDC1enable is cleared
to LOW after power-on reset).
2. Set SWENB to HIGH.
3. Depending on the data size of EDID data, set EX_DAT
to LOW (128 bytes) or HIGH (256 bytes).
4. Use substantial moving commands (DDCADR,
RAMBUF involved) to move the entire EDID data to
RAM buffer.
5. Reset SWENB to LOW.
MOV R0, #200; MOVX A, @R0.
6. Reset DDCADR to 00H.
The address pointer DDCADR is tied to the DDC1
transmitter here. To avoid the interference to the content
of DDCADR, it has to address the RAM buffer through the
MOVX command. While EX_DAT = HIGH, the entire RAM
buffer is covered by the pointing range of the address
pointer DDCADR, with the capability of the post increment;
no matter whether the access is done by DDC1 related
hardware (SWENB = 0) or software (SWENB = 1).
7. Set DDC1enable to HIGH enabling the DDC1
hardware; during the synchronization phase (the first 9
VCLK clocks) the first data byte will be loaded into the
shift register of the transmitter through the hold
register.
If SWENB is set at logic 1, then after the valid
synchronization, the DDC1 interrupt will be invoked
(interrupt vector address 002BH). The service routine
should fill the hold register DDCDAT (SFR address 9FH)
with the first data byte either from the internal ROM (part
1997 Dec 12
P83Cx80; P87C380
47
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
handbook, full pagewidth
DDC1_INT
DDC1 enable
00
01
11
01
11
01
SCL
1
VCLK
tsu(DDC1)
2
3
4
5
BIT
6
BIT
7
High Z
SDA
6
7
8
9
tVCLKH
1
2
BIT
5
3
4
BIT
4
5
BIT
3
BIT
2
BIT
1
6
7
8
tDOV
BIT
BIT
0 High Z 7
9
1
MGG032
tVCLKL
Fig.25 Transmission protocol in DDC1 interface.
17.4
According to the DDC2B specification:
DDC2B protocol
• A0H (for write mode) and
The DDC2B construction is based on the Philips I2C-bus
interface. However, in the level of DDC2B, PC host is fixed
as the master and the monitor is always regarded as the
slave. Both master and slave can be operated as a
transmitter or receiver, but the master device determines
which mode is activated. For details of the I2C-bus
interface, please refer to the Philips publication
“The I2C-bus and how to use it” ordering number
9398 393 40011 and/or the “Data Handbook IC20”.
• A1H (for read mode),
are assigned as the default address of monitors.
The reception of the incoming data in write mode or the
updating of the outgoing data in read mode should be
finished within the specified time limit. However, it is not
necessary for EDID data to be stored on-chip. It is also
possible to have access to the external EEPROM/ROM
through another set of I2C-bus interface and pre-store
those data in the RAM buffer. If software on the slave side
cannot react to the master in time, based on I2C-bus
protocol, SCL pin can be stretched LOW to inhibit the
further action from the master. The transaction can be
proceeded in either byte or burst format.
In the P83C880, one more pair of I2C-bus pins SCL1,
SDA1 and an I2C-bus hardware interface logic are
dedicated to perform DDC2B/DDC2B+/DDC2AB
protocols. The built-in address pointer mentioned in
Section 17.3 can be used to speed up the processing of
service routines for the access of the internal ROM or a
dedicated RAM buffer.
1997 Dec 12
48
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
17.5
Nevertheless, the command/information sequence
between host and monitor must conform to the
specification of ACCESS.bus.
DDC2AB/DDC2B+ protocol
DDC2AB/DDC2B+ is a superset of DDC2B. Monitors that
implement DDC2AB/DDC2B+ are full featured
ACCESS.bus devices. Essentially, they are similar to
DDC2B. The I2C-bus interface forms the fundamental
layer for both protocols. However, in DDC2AB/DDC2B+
the default address for monitors is assigned to 6EH
instead of A0H and A1H in DDC2B. Monitors and hosts
can play both the roles of master and slave. Under this
kind of protocol, it is easy to extend the support for hosts
to read VESA Video Display Information Format (VDIF)
and remotely control monitor functions.
Timing rules specified in ACCESS.bus such as maximum
response time to RESET message (<250 ms) from host,
maximum time to hold SCL LOW (<2 ms) etc., can be
satisfied through software checks and built-in timers such
as Timer 0 and Timer 1 in the P83C880. In
DDC2AB/DDC2B+ the monitor itself can act as a master to
activate the transaction. The default address assigned for
the host is 50H.
Figure 26 shows the overview and relationship between
software and the existing I2C-bus hardware for the DDC
interface.
The read/write protocols can be the same as described in
Section 17.4.
handbook, full pagewidth
P83Cx80; P87C380
DDC INTERRUPT
VECTOR ADDRESS
(002BH)
CHECK MODE FLAG IN DDCCON
SWENB = 1
MODE = 1
MODE = 0
DDC2B+/DDC2AB
COMMAND
RECEIVED
DDC2B
COMMAND
RECEIVED
DDC2B+/DDC2AB
UTILITIES
DDC2B
UTILITIES
SWENB = 0
I2C-BUS
SERVICE ROUTINES
DDC1
UTILITIES
I2C-BUS INTERFACE
(HARDWARE)
DDC1 TRANSMITTER
(HARDWARE)
MGG035
Fig.26 The conceptual structure of the DDC interface.
1997 Dec 12
49
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
17.6
P83Cx80; P87C380
RAM buffer for the system and DDC application
The architecture of the RAM buffer is set up in a flexible configuration to use the RAM resource to a maximum. In principle
the RAM buffer can be shared as system or DDC RAM buffer. The relationship among those applications is arranged as
shown in Table 42.
Table 42 Relation between system RAM and DDC RAM
AUX RAM 0 TO 127
MODE
EX_DAT SWENB
DDC1
DDC2
0
0
0
1
1
0
1
1
0
1
1
1
NORMALLY
RESERVED FOR
NOTE
1, 2 and 3
DDC1 EDID data
NORMALLY
RESERVED FOR
−
3 and 4
1 and 2
4
DDC2 EDID data
AUX RAM 128 TO 255
DDC1 EDID data
AVAILABLE
FOR
system access
−
NOTE
2
−
1, 2 and 5
4 and 5
3
−
system access
−
−
DDC2 EDID data
−
5
Notes
1. Read/write through MOVX instruction might conflict with the access from DDC1 hardware. So the access from CPU
by using MOVX instruction is forbidden.
2. READ/WRITE through DDCADR and RAMBUF registers has the conflicting problem also. Even the content of
DDCADR, which should be employed by DDC1 hardware, will be damaged. So it is inhibited to use this type of
access.
3. If DDCADR reaches 127 it will automatically wrap around to 0 after the access is done.
4. The access conflict can be avoided because DDC1 access is done by the interrupt service routine. However, the
EDID transferring from the RAM buffer should be finished within 40 µs.
5. If DDCADR reaches 255 it will automatically wrap around to 0 after the access is done.
18 I2C-BUS INTERFACE
The P83C880 has a software I2C-bus interface that can be used in master mode. Full details of the I2C-bus are given in
the 80C51 family “Data Handbook IC20” and/or the document “The I2C-bus and how to use it” (ordering number
9398 393 40011).
The I2C-bus interface lines SDA and SCL share the same pins as Port 1 lines P1.1 and P1.0 respectively; selection is
done via the S1E bit in SFR DFCON (address C0H).
1997 Dec 12
50
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
• Fast enough to react on any mode change.
detector is also able to recognize the operational mode
and generate the fixed free running frequency for HSYNC
and VSYNC in some specific modes like stand-by,
suspend and power-off. Two display patterns, the white
and the cross hatch, can be displayed for the self test in
the free running mode.
• Possibility to detect the polarity of HSYNC without extra
input pin.
More on Device Power Management Signalling (DPMS)
will be explained in Chapter 20, “Power management”.
19 HARDWARE MODE DETECTION
Due to the many restrictions for mode detection via
software, a hardware mode detector is introduced in the
P83C880. This feature has the following advantages:
• Higher accuracy to measure the HSYNC and VSYNC
frequency
19.1
• Relieves the CPU and valuable timers/counters in the
microcontroller from lengthy mode detection
Special Function Register for mode detection
and sync separation
There are 4 SFRs related to mode detection and sync
separation: MDCST (SFR address F8H); HFHIGH (SFR
address FCH); VFHIGH (SFR address FDH) and VFLHFL
(SFR address FEH).
• In reduced power modes, e.g. Idle mode, the mode
detection is still active.
Apart from the above mentioned benefits, some extra
features can be achieved through hardware mode
detection. The composite sync separation can be done
while mode detection continues. The various formats of
HSYNC and VSYNC output pulses are provided to fit into
different applications.
Five SFRs are applied for the output pulse generation of
HSYNC and VSYNC and the display pattern generation for
the self test: HFP (SFR address F6H); HFPOPW (SFR
address F7H); VFP (SFR address F9H); VFPOPW (SFR
address FAH) and PULCNT (SFR address FBH).
Since the information of the operational modes defined in
Device Power Management Signalling (DPMS) for
monitors is embedded in HSYNC and VSYNC, the mode
These SFRs are described in detail in Section
19.1.1 to 19.1.9.
MODE DETECTION/SYNC SEPARATION CONTROL AND STATUS REGISTER (MDCST)
19.1.1
Table 43 Mode Detection/sync separation Control and Status Register (SFR address F8H)
7
6
5
4
3
2
1
0
MARCH
CHREQ
XSEL
HSEL
Hpres
Vpres
Hpol
Vpol
Table 44 Description of MDCST bits
BIT
SYMBOL
DESCRIPTION
7
MARCH
Mode detection enable. If MARCH = 1, mode detection is enabled. If MARCH = 0,
mode detection is disabled. Default value MARCH = 1 to guarantee that mode detection
is automatically executed after power-on reset.
6
CHREQ
Polarity or frequency change. If CHREQ = 1 then the polarity or frequency change
happened. The polarity or frequency is detected after a CHREQ HIGH-to-LOW transition,
because the mode change becomes stable after the CHREQ HIGH-to-LOW transition.
5
XSEL
Indicates if the clock used for the mode detection and the pulse generation is 1⁄2 × fclk.
If XSEL = 1, the internal clock is1⁄2 × fclk. If XSEL = 0 the internal clock is equal to fclk.
4
HSEL
Indicates the horizontal sync input coming from HSYNCin (pin HSYNCin/PROG) or
CSYNCin (pin CSYNCin/P1.6). If HSEL = 1, CSYNCin is the input pin. If HSEL = 0,
HSYNCin is the input pin.
3
Hpres
Indicates the presence of HSYNC. If Hpres = 1, HSYNC is present. If Hpres = 0, HSYNC
is not present.
1997 Dec 12
51
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
BIT
SYMBOL
DESCRIPTION
2
Vpres
Indicates the presence of VSYNC. If Vpres = 1, VSYNC is present. If Vpres = 0, VSYNC
is not present.
1
Hpol
Indicates the polarity of HSYNC. If Hpol = 0, polarity is positive (active HIGH; i.e. HIGH
at horizontal retracing period). If Hpol = 1, polarity is negative (active LOW; i.e. LOW at
horizontal retracing period).
0
Vpol
Indicates the polarity of VSYNC. If Vpol = 0, polarity is positive (active HIGH; i.e. HIGH
at vertical retracing period). If Hpol = 1, polarity is negative (active LOW; i.e. LOW at
vertical retracing period).
19.1.2
HORIZONTAL PERIOD COUNTING HIGH-BYTE REGISTER (HFHIGH)
Table 45 Horizontal Period Counting High-byte Register (SFR address FCH)
7
6
5
4
3
2
1
0
HF.11
HF.10
HF.9
HF.8
HF.7
HF.6
HF.5
HF.4
Table 46 Description of HFHIGH bits
BIT
SYMBOL
7 to 0
HF.11 to HF.4
19.1.3
DESCRIPTION
Indicate the high byte of the value counted by mode detector for 4
horizontal scanning periods.
VERTICAL PERIOD COUNTING HIGH-BYTE REGISTER (VFHIGH)
Table 47 Vertical Period Counting High-byte Register (SFR address FDH)
7
6
5
4
3
2
1
0
VF.11
VF.10
VF.9
VF.8
VF.7
VF.6
VF.5
VF.4
Table 48 Description of VFHIGH bits
BIT
7 to 0
SYMBOL
DESCRIPTION
VF.11 to VF.4
Indicate the high byte of the value counted by mode detector for 1
vertical field/frame period.
VERTICAL AND HORIZONTAL PERIOD COUNTING LOW-NIBBLES REGISTER (VFLHFL)
19.1.4
Table 49 Register containing the low nibbles of the Horizontal and Vertical Period Counting (SFR address FEH)
7
6
5
4
3
2
1
0
VF.3
VF.2
VF.1
VF.0
HF.3
HF.2
HF.1
HF.0
Table 50 Description of VFLHFL bits
BIT
SYMBOL
7 to 4
VF.3 to VF.0
Indicate the low nibble of the value counted by mode detector for 1 vertical field/frame
period.
3 to 0
HF.3 to HF.0
Indicate the low nibble of the value counted by mode detector for 4 horizontal scanning
periods.
1997 Dec 12
DESCRIPTION
52
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
19.1.5
P83Cx80; P87C380
HORIZONTAL FREE RUNNING FREQUENCY/PERIOD BYTE REGISTER (HFP)
Table 51 Horizontal free running Frequency/Period Register byte Register (SFR address F6H)
7
6
5
4
3
2
1
0
HFP9
HFP8
HFP7
HFP6
HFP5
HFP4
HFP3
HFP2
Table 52 Description of HFP bits
BIT
7 to 0
19.1.6
SYMBOL
DESCRIPTION
HFP9 to HFP2
Indicate the upper byte of the 10 bits for programming the free running
HSYNC output pulse.
HORIZONTAL FREE RUNNING FREQUENCY/PERIOD AND PULSE WIDTH REGISTER (HFPOPW)
Table 53 Horizontal free running Frequency/Period and Pulse Width Register (SFR address F7H)
7
6
5
4
3
2
1
0
VSEL
HFP1
HFP0
HOPW4
HOPW3
HOPW2
HOPW1
HOPW0
Table 54 Description of HFPOPW bits
BIT
7
SYMBOL
DESCRIPTION
VSEL
Indicates whether the internal vertical sync is coming from the external
VSYNC input pin (VSYNCin/OE) or separated from the composite signal.
If VSEL = 0, vertical sync coming from the external VSYNC input pin.
If VSEL = 1, vertical sync separated from the composite signal.
6 to 5
HFP1 to HFP0
Indicate the lower two of the 10 bits for programming the free running
horizontal output pulse.
4 to 0
HOPW4 to HOPW0
Indicate the horizontal output pulse width.
VERTICAL FREE RUNNING FREQUENCY/PERIOD BYTE REGISTER (VFP)
19.1.7
Table 55 Vertical free running Frequency/Period byte Register (SFR address F9H)
7
6
5
4
3
2
1
0
VFP9
VFP8
VFP7
VFP6
VFP5
VFP4
VFP3
VFP2
Table 56 Description of VFP bits
BIT
SYMBOL
7 to 0
VFP9 to VFP2
1997 Dec 12
DESCRIPTION
Indicate the upper byte of the 10 bits for programming the free running
vertical output pulse.
53
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
19.1.8
P83Cx80; P87C380
VERTICAL FREE RUNNING FREQUENCY/PERIOD AND PULSE WIDTH REGISTER (VFPOPW)
Table 57 Vertical free running Frequency/Period and Pulse Width Register (SFR address FAH)
7
6
5
4
3
2
1
0
−
−
VFP1
VFP0
VOPW3
VOPW2
VOPW1
VOPW0
Table 58 Description of VFPOPW bits
BIT
SYMBOL
DESCRIPTION
−
Reserved.
5
VFP1
4
VFP0
Indicate the lower two bits of the 10 bits for programming the free running
vertical output pulse.
VOPW3 to VOPW0
Indicate the vertical output pulse width.
7 to 6
3 to 0
PULSE GENERATION CONTROL REGISTER (PULCNT)
19.1.9
Table 59 Pulse generation Control Register (SFR address FBH)
7
6
5
4
3
2
1
0
CLMPEN
PATTYP
VPG
PVSI
HPG1
HPG0
FBPO
PHSI
Table 60 Description of PULCNT bits
BIT
SYMBOL
DESCRIPTION
7
CLMPEN
Clamping pulse output (CLAMP) enable. If CLMPEN = 1, pin
PWM8/CLAMP/P3.0 is switched to the CLAMP output. If CLMPEN = 0,
the CLAMP function is disabled. The CLAMP function always overrides
other alternative functions such as PWM8 and P3.0.
6
PATTYP
Basic display patterns selection. If PATTYP = 0, the white display
pattern is selected. If PATTYP = 1, the cross hatch display pattern is
selected.
5
VPG
Vertical pulse output modes selection. If VPG = 0, a free running
vertical sync pulse signal is selected. If VPG = 1, a vertical substitution
pulse signal is selected.
4
PVSI
Vertical output pulse polarity selection. If PVSI = 0, the positive
polarity is selected. If PVSI = 1, the negative polarity is selected.
HPG1 to HPG0
Horizontal pulse output modes selection; see Table 61.
1
FBPO
The clamp pulse at the back porch or at the front porch selection.
This bit is only valid when CLMPEN is set HIGH. If FBPO = 1, the
horizontal back porch clamp pulse is selected. If FBPO = 0, the
horizontal front porch clamp pulse is selected.
0
PHSI
Polarity of the horizontal and clamping output pulse indication.
If PHSI = 0, the positive polarity is selected. If PHSI = 1, the negative
polarity is selected.
3 to 2
1997 Dec 12
54
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
Table 61 Horizontal pulse output modes
HPG1 HPG0
MODES
0
0
free running horizontal sync pulse signal
0
1
horizontal substitution pulse signal
1
0
reserved
1
1
the incoming horizontal sync is followed and delivered out but the horizontal substitution pulse is
disabled, while the incoming HSYNC is missing
1997 Dec 12
55
1997 Dec 12
56
XSEL
fclk
VSYNCin
DIV 2
DIV 76
FOSV
FOSH
SYNC
SEPARATION
V
H
12
Hper
Vpol
12
12
Vper
FBPO
10
VOPW3 to VOPW0
VPG
4
VFP9 to VFP0
HPG1 to HPG0
5
Vper or Vpol
change
MUX
PVSI
PHSI
MUX
10
microcontroller core
CLAMP
HSYNCout
MGG036
VSYNCout
MODE DETECT
AND
PULSE GENERATION
CONTROL
10
VFP9 to VFP0
controls
HFP9 to HFP0
V-PULSE
GENERATOR
Hper or Hpol
change
12
Vper
10
H-PULSE
GENERATOR
CHREQ
(Change Interrupt Request)
12
Hper
12
Vper
12
Hper
Hper
HFP9 to HFP0
HOPW4 to HOPW0
CAPTURE
REGISTERS
Hpol
microcontroller core
Vpres
Hpres
Vpol
Hpol
V-MODE
DETECTION
Vpres
Hpres
H-MODE
DETECTION
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
Fig.27 Block diagram of the hardware mode detection and pulse generation.
VSYNC
POLARITY
CORRECTION
Vpol
Hpol
HSYNC_P
dbook, full pagewidth
MUX
HSYNC
POLARITY
CORRECTION
19.2
CSYNCin
HSYNCin
HSEL
Philips Semiconductors
Product specification
P83Cx80; P87C380
System description
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
19.2.1
CLOCK PRESCALER
19.2.3
 2 12 × f

H(min)
f clk ≤  ----------------------------- = 15.36 MHz 


4
19.2.4
The same holds for the vertical part of the mode detection.
Here the minimum vertical sync frequency fV(min) = 40 Hz,
so the maximum clock frequency to avoid overflow in a
12-bit counter, equals:
 12

FOSV ≤  2 × f V(min) = 163.84 kHz
Due to the fact that the differentiator reacts upon every
LOW-to-HIGH transition even an interlaced composite
sync will be separated correctly. Note further that the sync
separation is taken from signal HSYNC_P which is
processed by the Horizontal Polarity Correction circuit but
not necessary with the fixed polarity. As a result the
polarity of the separated vertical sync Vsep will vary with
the incoming composite signal, and in case no composite
sync is present the level will be LOW. According to this
algorithm, Vsep will be always 1⁄4HSYNC period shift to the
original VSYNC window. The 8-bit counter in Fig.28 is
stopped at its maximum of FFH, otherwise it will start again
from zero which results in a wrong enable pulse for the
D flip-flop.
To get a maximum accuracy without overflow the clock of
the horizontal section FOSH, should be prescaled down to
this value of FOSV. Thus the scale factor should be at
3
 FOSH ( max ) 12 × 10 k Hz

least: n ≥  ------------------------------ = ----------------------------------- = 73.2 
163.84 kHz
163.84 kHz
Take n = 76 as a suitable scale factor as shown in Fig.23.
Table 62 Clock frequencies
19.2.2
FOSV
(MHz)
10
10
131.6
12
12
157.9
16
8
105.3
All kinds of composite sync input shown in Chapter 27 can
be dealt with by this function. There are 6 types of
composite sync waveforms which can be accepted by the
sync processor (see Fig.39).
HORIZONTAL POLARITY CORRECTION
In order to simplify the processing in the following stages,
the HSYNC polarity correction circuit is able to convert the
input sync signals to positive polarity signals in all
situations. However, be aware that this correction is
achieved by the aid of Hpol and Hper signals. Hpol and
Hper are only settled down in several horizontal scanning
lines (61 lines, if fHSYNC goes up) or a few milliseconds
(worst case 1.2 ms, if fHSYNC becomes inactive) after
power-on or timing mode change.
1997 Dec 12
VERTICAL SYNC SEPARATION
This function will separate the vertical sync out of the
composite sync. To do so the change in polarity during
VSYNC interval can be utilized to extract VSYNC as
shown in Fig.28. The differentiated sync pulse derived
from HSYNC_P is used to reset an 8-bit upcounter.
At 1⁄4 of the line time the level of the incoming sync at that
moment is clocked into the last D flip-flop. Be aware that
1⁄ of the line period equals 1⁄ of parameter Hper because
4
16
Hper is calculated based on 4 consecutive lines.
From the calculation above it is clear that there will be no
overflow if fclk is 10 or 12 MHz. However, for a 16 or
24 MHz crystal fclk has to be divided by a factor of 2 to get
a correct clock frequency FOSH for the horizontal part of
the mode detection. If fclk used is 10, 12 or 16 MHz then
FOSH will be respectively 10, 12 or 8 MHz.
FOSH
(MHz)
VERTICAL POLARITY CORRECTION
The purpose of the vertical polarity correction is similar to
the horizontal polarity correction. However, it takes a
longer time to get the correct result after power-on or a
timing mode change because at least 5 frames are needed
to stabilize Vper from the input sync signals.
To reach the required 12 bit accuracy and the reasonable
crystal clock frequency, the line time of 4 consecutive lines
is measured (see Section 19.2.5). Doing so the maximum
crystal clock frequency is:
fclk
(MHz)
P83Cx80; P87C380
57
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
handbook, full pagewidth
HSYNC_P
DIFFERENTIATOR
R
E
FOSH
8-BIT
COUNTER
Q7 to Q0
D
COMPARATOR
FOR
SYNC
SEPARATION
Hper
E D-FF Q
Vsep
DIV 16
MGG037
Fig.28 Vertical sync separator.
19.2.5
HORIZONTAL MODE DETECTION
This function block determines the following 4 parameters: Hper, Hpol, Hpres and Hcha. The functional block diagram is
shown in Fig.29.
The 12-bit counter for the determination of the horizontal period has a synchronous reset and will be reset by the
prescaled and differentiated horizontal pulse HSYNC_P, coming from the horizontal prescaler, or in case the counter
reaches the value FF0H as defined by the comparator. The latter situation will occur if no sync pulses are coming in or
if the frequency of the incoming sync pulses is too low.
The 12-bit register, that will store the 4 line time period, is only enabled if the signal HENA is HIGH.
19.2.5.1
Parameter Hper
Based on this configuration, the resulting accuracy for Hper will be:
100% × f H
100%
Accuracy in H = ------------------------------------------------------------------- = -------------------------4 × FOSH
(horizontal counter value)
Table 63 Accuracies
XTAL (fclk)
(MHz)
FOSH
(MHz)
ACCURACY IN H AT 30KHZ
(%)
ACCURACY IN V AT 50HZ
(%)
10
10
0.075
0.038
12
12
0.063
0.032
16
8
0.094
0.048
1997 Dec 12
58
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
When the new input HSYNC is changed to a static state,
the HSYNC frequency counter reaches 4080. In order to
have a faster response of the mode change interrupt, the
2-bit counter is not used and the mode change interrupt is
issued immediately. The time from mode change to
interrupt issued is approximately
((4080 + 5) × 83 ns) − (n × Hperiod(previous)), where
n = 1, 2, 3 or 4.
A 12-bit counter is used to measure the frequency of
HSYNC. Every 4 HSYNC periods are measured and
compared with the previous locked HSYNC frequency; the
counter is reset every 4 HSYNC periods. The base clock
1
to the counter is ------------------- = 83 ns for a 12 MHz system
12 MHz
clock. If the new HSYNC frequency is larger than the
previous HSYNC frequency, there is a 4-bit counter to
avoid the noise or the temporary frequency shift.
When the 4-bit counter counts up to 15 for the comparison
Hfreq(new) > Hfreq(previous), then the mode change interrupt
is issued. The time from mode change to interrupt issued
is approximately 4 × Hperiod(new) × 15 or
(4 × Hperiod(new) × 14) + n × Hperiod(previous)),
where n = 1, 2 or 3.
19.2.5.2
Parameter Hpres
The presence indicator Hpres, as stored in the SR flip-flop,
contains some hysteresis, as required due to the two
threshold settings in the comparator. The SR flip-flop will
be set, indicating that no active sync (or sync with a too low
frequency) is coming in if the counter reaches a value of
FF0H (4080 decimal). The corresponding horizontal sync
frequency is:
4 × FOSH
4 × FOSH
f H = Hfreq1 = -------------------------------------------- = --------------------------( Counter value )
4080
If the new HSYNC frequency is not in the static state and
is smaller than the previous HSYNC frequency, the time
from mode change to interrupt issued is approximately
(4 × Hperiod(new) × 3) − (n × Hperiod(previous)), where
n = 1, 2, 3 or 4. The static state is considered as the state
where the 12-bit counter, for measuring the HSYNC
frequency, reaches 4080.
The SR flip-flop will be reset, indicating that an active sync
is present, if the counter reaches a value lower than FC0H
(4032 decimal). The corresponding horizontal sync
frequency is:
4 × FOSH
4 × FOSH
f H = Hfreq2 = -------------------------------------------- = --------------------------( Counter value )
4032
For a 12 MHz system clock, the static state is equal to
1
1
--------------------------------- = ----------------------- = 11.8 kHz .
4080
84660 ns
83 ns × ------------4
If the input HSYNC frequency is less than 11.8 kHz, it will
be regarded as static state. A 2-bit counter is used to avoid
the noise or the temporary shift.
The hysteresis result,
Hysteresis = ( Hfreq1 – Hfreq2 ) ⁄ Hfreq1 ,
is shown in Table 64.
When the 2-bit counter counts up to 3 for the comparison
‘static state’ < Hfreq(new) < Hfreq(previous), then the mode
change interrupt is issued.
Table 64 Hysteresis in the Hpres detection
XTAL (fclk)
(MHz)
FOSH
(MHz)
Hfreq1
(MHz)
Hfreq2
(MHz)
HYSTERESIS
(%)
10
10
9.804
9.921
1.2
12
12
11.765
11.905
1.2
16
8
7.843
7.937
1.2
1997 Dec 12
59
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
19.2.5.3
Parameter Hpol
19.2.5.4
The mode change interrupt will be issued after 36 to 40
periods of the HSYNC when the polarity is changed from
negative to positive. The polarity indicator Hpol will be
changed from a logic 1 to a logic 0. The mode change
interrupt will be issued after the 60 periods of the HSYNC
when the polarity is changed from positive to negative. The
Hpol will be changed from a logic 0 to a logic 1. A logic 0
represents a positive polarity and a logic 1 represents a
negative polarity.
P83Cx80; P87C380
Parameter Hcha
If Hcha is set to HIGH indicating that the period time has
changed for a long period, the Hper and Hpres will be
updated. If the measured period time has become stable
then the two counters will start to count down and the
HENA signal is set to LOW again, thereby disabling the
register Hper and the SR flip-flop for Hpres parameter.
handbook, full pagewidth
HENA
Hres
Hcnt
HSYNC_P
R
Q 11 to Q0
12-BIT
COUNTER
FOSH
FOSH
D11 to D0
12-BIT
E
REGISTER
Q11 to Q0
Hlow
Hper
CHANGE
DETECTOR Hhgh
Q
S
Hper
SR-FF
R
Q
D
Q
E D-FF
DIV 16
FOSH
Fig.29 Horizontal mode detection.
1997 Dec 12
FOSH
Hcha
Hpres
MGG038
Hper and Hpol
DECISION
CIRCUIT
HSYNC
MODE
CHANGE
STABILIZATION
AND
COMPARISON
CIRCUIT
60
Hpol
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
19.2.6
VERTICAL MODE DETECTION
P83Cx80; P87C380
The hysteresis result,
Hysteresis = ( Vfreq1 – Hfreq2 ) ⁄ Hfreq1 ,
is shown in Table 64.
To detect the vertical mode parameters Vper, Vpol and
Vpres, a circuit can be used which is almost similar to that
for the horizontal mode detection. The only difference is
that now the period time of one frame (instead of 4 lines)
is measured. The presence indication for the vertical sync
also contains a hysteresis of about 1.2%.
If the new VSYNC frequency is larger than the previous
VSYNC frequency, the time from mode change to interrupt
issued is approximately from
((Vperiod(new) × 2) + Vperiod(previous)) to (Vperiod(new) × 3).
If the new VSYNC frequency is not in the static state and
is smaller than the previous VSYNC frequency, the time
from mode change to interrupt issued is approximately
from Vperiod(new) to Vperiod(new) × 2. If the new VSYNC
frequency is in the static state, the time from mode change
to interrupt issued is approximately from
(4080 × 6.3 us) − Vperiod(previous) to 4080 × 6.3 µs.
The formula to calculate the hysteresis is also similar to the
condition of HSYNC processing. A 12-bit counter is used
to count the clock number during one frame. Again FF0H
(4080 decimal) and FC0H (4032 decimal) are taken as the
threshold for Vfreq1 and Vfreq2 respectively, but the clock
FOSV = FOSH/76. Vfreq1, Vfreq2 and Hysteresis are
calculated as follows:
FOSV
FOSH
f V = Vfreq1 = -------------------------------------------- = -------------------------( Counter value )
76 × 4080
FOSV
FOSH
f V = Vfreq2 = -------------------------------------------- = -------------------------( Counter value )
76 × 4032
Table 65 Hysteresis in the Vpres detection
(fclk)
(MHz)
FOSH
(MHz)
Vfreq1
(MHz)
Vfreq2
(MHz)
HYSTERESIS
(%)
10
10
32.25
32.63
1.2
12
12
38.70
39.16
1.2
16
8
25.80
26.11
1.2
The polarity can be measured by looking to the level of the
input sync at 1⁄4 of the frame time. The mode change in
vertical the frame period will be detected if there is a
change for a longer time than 3 frame periods.
2. A pulse starting at the beginning of the input horizontal
sync but now with a fixed length, or a substitution pulse
(with fixed length).
The accuracy of Vper can calculated by the following
formula:
4. The same pulse as the input horizontal sync. The
substitution pulse is inhibited even if HSYNC is
missing.
3. A free running sync pulse.
100% × f
100%
Accuracy in V = ------------------------------------------------------------ = -------------------------V(vertical counter value)
( FOSV )
To be able to generate a substitution pulse the down
counter, depicted in Fig.23, is loaded at each incoming
sync with a period time just a bit longer than the measured
Hper. If now normal syncs are present then the counter will
be loaded just before it reaches 000H. Therefore the
counter will not generate a pulse (in Fig.23, HPST remains
LOW). However, if a sync pulse is missing the counter will
reach 000H and generates a substitution pulse, HPST. At
the same time it will load itself again for the next run. To
generate free running pulses the only thing to do is to load
the down counter with the parameter HFP and to stop the
load pulses coming from the input sync, HSYNC_P. So,
the signal HPST is either a free running pulse or a pulse in
case an input sync is missing.
100% × 76 × f
= --------------------------------------V( FOSH )
The hysteresis results and the accuracy of Vper are shown
in Table 63.
19.2.7
HORIZONTAL PULSE GENERATOR
Through the control flags, HPG1 and HPG0, the horizontal
pulse generator is able to generate the HSYNCout signal
with the following formats:
1. The same pulse as the input horizontal sync, or a
substitution pulse (with a fixed length) in case of a
missing sync pulse.
1997 Dec 12
61
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
The 5-bit down counter is used to generate a pulse with
pulse width tW(H). As shown in Fig.23, the SR flip-flop will
be set by either HPST (free running/missing sync pulse) or
by the leading or trailing edge of the incoming sync pulse,
HSYNC_P. In the same way the SR flip-flop will be reset
by either the end of the incoming sync pulse or by the
pulse width counter.
P83Cx80; P87C380
If necessary (HPG1, HPG0: 1, 1), the substitution pulse
can be suppressed and only the incoming HSYNC pulse
will be delivered out. The frequency of the free running
FOSH
pulse is: f H(free) = ---------------Hfp
The pulse width of the free running mode is:
tW(H) = TFOSH × (HOPW<4:0>)
handbook, full pagewidth
HPST
'0'
COMPARATOR
HSYNC_P
HFP
Hper
D9..0
DATA
LOAD
DECISION
Q9..0
DOWN
COUNTER
L
FOSH
PHSI
HPG1 to HPG0
HOPW
S
PULSE
RISE/FALL
GENERATOR
Q
HSYNCout
SR-FF
Q
R
PULSE
WIDTH
GENERATOR
FOSH
MGG039
Fig.30 Horizontal pulse generator.
19.2.8
VERTICAL PULSE GENERATOR
19.2.9
The clock used in this vertical pulse generator must be
switchable between FOSV (needed to generate missing
sync pulses) and HPST (free running syncs from the
horizontal pulse generator) needed in the free running
mode. In the latter situation one vertical sync pulse (i.e.
one frame) will be generated by including an integer
number of the horizontal scanning lines (i.e. HPST). In this
case, the pulse width is also counted by HPST. The rest is
more or less equal to the horizontal pulse generator.
This function captures the 6 parameters, Hper, Hpol,
Hpres, Vper, Vpol and Vpres such that the current value of
these parameters is available for the microcontroller core
(software) at all times. The mode change interrupt will be
activated if:
• The horizontal period changes
• The vertical period changes
• The horizontal polarity changes
• The vertical polarity changes.
The frequency of the free running pulse is:
f H(free)
f V(free) = ----------------2 × Vfp
19.2.10 CONTROL
All necessary control signals for the complete hardware
mode detection are mentioned in Section 19.1.
The pulse width of the free running mode is:
tW(V) = TH(free) × [(VOPW<3:0>) + 2] × 2
1997 Dec 12
CAPTURE REGISTERS
62
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
decided by the fixed number of FOSH clock and FOSV
clock (see Fig.31). Therefore, the position or dimension of
the white pattern is much related to HFP and VFP. The
duration of every two hatch lines (accordingly, the number
of hatch lines in the horizontal or vertical direction) will
depend on two fixed numbers (32, 32) which divide HFP
and VFP. For both white and cross hatch patterns, the
displayed pattern might look different in the different timing
modes and the symmetric display is not guaranteed.
However, they should be sufficient to be used as the
indicator to report the status of the monitor. Figure 31
demonstrates the display of the two patterns.
19.2.11 THE DISPLAY PATTERN GENERATION
For certain events such as disconnection with the host or
the life test of monitor sets, it is convenient to have certain
display patterns shown on the monitor as the indication of
the operation of the monitor. The P83C880 provides two
simple patterns, the white pattern and the cross hatch
pattern for this purpose in the free running mode.
In the free running mode, the intervals of HSYNC and
VSYNC are determined by the 10-bit registers, HFP and
VFP. Based on the HFP and VFP, the internal down
counter will determine the starting or ending of the HSYNC
and VSYNC. The starting position, ending position and the
duration of the adjacent hatch lines are all related to the
programmed value of HFP and VFP. As a matter of fact,
the starting and ending position of the white pattern are
handbook, full pagewidth
32 FOSH
P83Cx80; P87C380
Two flags: PATENA (SFR PWME2) and PATTYP (SFR
PULCNT), are used to control the pattern display; for
detailed usage of those control bits refer to Section 7.3.6
and Section 19.1.9.
16 FOSH
32 FOSH
32 FOSH
16 FOSH
32
HPST
32
HPST
16
HPST
1. THE WHITE PATTERN
2. THE CROSS HATCH
MGG040
Fig.31 Two self test display patterns.
The bit PHSI (PULCNT.0) is used to set the output polarity
of HSYNCout and the clamping pulse. If PHSI is LOW then
the output polarity will be positive, otherwise the output
polarity is negative.
19.2.12 CLAMP OUTPUT
To facilitate the video processing in the following stage, the
clamping pulse can be delivered on pin
PWM8/CLAMP/P3.0 by setting flag CLMPEN (PULCNT.7)
to HIGH. The clamping pulse always accompanies the
HSYNCout pulse. Therefore, even in the free running mode
the clamping pulse is still present as long as the CLMPEN
bit is set. Flag FBPO (PULCNT.1) can be used to choose
the front porch clamp pulse (FBPO = 0) or the back porch
clamp pulse (FBPO = 1). The pulse width of the clamping
output signal is fixed to 8 FOSH clocks.
1997 Dec 12
63
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
19.3
In fact, the detection of the Device Power Management
Signalling (DPMS) modes like ‘Normal’, ‘Standby’,
‘Suspend’, ‘Power off’, etc. and sync separation are mixed
together with the display mode detection.
System operation
After a successful power-on reset, the P83C880 will
automatically start the mode detection and sync
separation by default. The output pulses of HSYNC and
VSYNC are delivered in the free running format by the
default setting. Since it takes at least 5 frames to finalize
the calculation of the HSYNC period, Hper, VSYNC period
and Vper, it is better to wait until the stable state is reached
to get the complete information after power-on reset.
Accordingly, Hpol, Vpol, Hpres, Vpres and sync separation
will be decided upon after Hper and Vper are settled. To
prevent interfering the CPU too often, the interrupt request
flag IE0 (SFR TCON) is only set if the mode (including
frequency or polarity) is changed. IE0 will be cleared either
by the CPU when the service routine is called (IT0 = 1) or
by the service routine itself (IT0 = 0).
The mode detection function provides the hardware
vehicle to facilitate the mode detection and related
activities. Nevertheless, to use this facility to a maximum,
the proper interaction between software and hardware is
still essential. When VSYNC is absent and HSYNC is
present, the polarity of HSYNC is always fixed. A software
flow chart example is illustrated in Fig.32.
19.3.1
DISPLAY POWER MANAGEMENT SIGNALLING
(DPMS) SPECIFICATION
According to the DPMS specification: Hfreq <10 kHz and
Vfreq <10 Hz indicates that HSYNC and VSYNC are
inactive. However, in the real application, there are no
modes running with 10 kHz≤ Hfreq≤15 kHz and
10 Hz≤ Vfreq≤40 Hz. Therefore, Hfreq = 15 kHz and
Vfreq = 40 Hz are chosen as the threshold to indicate an
active or inactive signal for HSYNC and VSYNC
respectively.
If it is required to reduce power dissipation or if it is
preferred to stabilize the entire system after power-on
reset before mode detection is proceeded, the bit MARCH
(SFR MDCST) can be cleared to logic 0. Mode detection
can be activated at the desired moment later on by setting
MARCH to a logic 1.
1997 Dec 12
P83Cx80; P87C380
64
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
handbook, full pagewidth
P83Cx80; P87C380
INTERRUPT OCCURS
IE0 IS SET
YES
IS Hpres = 1?
NO
IS Vpres = 1?
IS Vpres = 1?
NO
YES
NO
YES
IS VSEL = 1?
NO
IF CSYNC IN?
(CHECK HSEL)
YES
NO
YES
SET HSEL = 0
SET VSEL = 0
CHANGE VSEL = 0
CHANGE VSEL = 1
SET HSEL = 1
SET VSEL = 1
MGG041
RETURN
Fig.32 Software procedure in system operation: Mode detection flow chart.
1997 Dec 12
65
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
The combination of Hpres and Vpres in relation to the
operating mode is shown in Table 66.
20 POWER MANAGEMENT
The P83C880 supports power management. The
hardware mode detection complies to the Device Power
Management Signalling (DPMS) according to the
specification of VESA. The microcontroller is able to
distinguish between ‘Normal’, ‘Standby’, ‘Suspend’ and
‘Power off’ mode by detecting the frequency of HSYNC
and VSYNC. HSYNC is an active signal if its frequency is
above 15 kHz; otherwise, it is inactive. For VSYNC 40 Hz
is the threshold to judge if it is active or inactive. See also
Section 19.3.1. The exact values for the threshold depend
on the chosen crystal oscillator frequency:
10, 12 or 16 MHz.
In the case of DDC2AB protocol, apart from hardware
mode detection, the protocol of ACCESS.bus also
supports Device Power Management Signalling (DPMS)
commands. In some operating modes the microcontroller
might enter a kind of power saving mode, i.e. Idle or
Power-down mode. In this situation the extremely low
retention voltage of 1.8 V for internal memory can support
the microcontroller to save its state before switching to Idle
or Power-down mode.
One set of I/O ports with the capability to drive LEDs can
help to highlight the current operating mode of monitors. It
is also possible to control the power consumption sources
like heater, main supply etc., through an I/O port in a
related operating mode.
The information about the status of HSYNC and VSYNC
can be represented by the bits, Hpres and Vpres in SFR
MDCST (address F8H).
Table 66 Display Power Management modes
OPERATING MODES
HSYNC
Hpres
VSYNC
Vpres
Normal
active
1
active
1
Standby
inactive
0
active
1
Suspend
active
1
inactive
0
Power off
inactive
0
inactive
0
The procedure to enter a specific control mode is as
follows:
21 CONTROL MODES
The microcontroller can operate in different control modes
(e.g. for emulation or OTP programming) by means of a
10-bit serial code that is shifted into the RESET input. The
signal at the XTAL1 pin serves as the shift clock.
1. Reset the microcontroller (CPU) by keeping the
RESET signal HIGH for at least 10 XTAL1 clock cycles
to escape any other control mode, plus at least 20 µs
(minimum of 24 internal clock cycles) to reset the
internal logic.
The code is built up as follows: 0 XXXXX 0101; whereby
the first ‘0’ is the start bit, followed by a 5-bit code and
completed by ‘0101’. The 5-bit code determines the mode.
2. Shift in the specific code for the required control mode
(e.g. 0 11000 0101 for Emulation mode) via the
RESET pin and the XTAL1 clock (MSB first).
Normal mode is reached when no code is shifted in, but
the RESET pin remains HIGH for at least 10 cycles of the
XTAL1 input plus 20 µs.
3. After the 10th bit the RESET signal should go LOW
within 9 cycles of XTAL1, otherwise the
microcontroller will enter Normal mode.
When an OTP Programming/Verification, Emulation or a
Test mode should be entered, the timing must be as
shown in Fig.34.
For the OTP Programming/Verification control modes see
Chapter 22.
The RESET signal is sampled on the rising edge of
XTAL1. Set-up and hold times for the RESET signal with
respect to the XTAL1 rising edge are 10 ns each.
1997 Dec 12
66
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
The signals and waveforms are given in Table 69 and
Fig.33. Pin connections to be used during Programming
and Verification are given in Table 68.
22 ONE TIME PROGRAMMABLE (OTP) VERSION
The OTP version P87C380 contains:
• 32 kbytes ROM
• 512 bytes RAM.
Table 67 Code for Programming/Verification of the
OTP version P87C180A
Next to the 32 kbytes ROM, another extra 384 bytes are
available. These bytes can be used for identification
purposes or to indicate the version number, etc. These
bytes are addressed via address lines A0 to A4.
Access to the OTP for program execution is done in
Normal mode. For writing and reading (Verification) of the
program memory and of the extra 384 bytes, different
control modes are used as shown in Table 67.
MEMORY
CODE
ROM: 32 kbytes (program memory)
010000 0101
Extra 384 bytes (memory)
010001 0101
ROM: 32 kbytes (verification)
011111 0101
Table 68 Pin assignments during
Programming/Verification mode
PIN
PIN
CONNECT TO
CONNECT TO
1
VSS
23
A2
2
VSS
24
A1
3
A13
25
A0
4
A12
26
RESET
5
A11
27
VSS
6
A10
28
VSS
7
A9
29
VSS
8
A8
30
VSS
9
XTAL1 (note 1)
31
VSS
10
XTAL2 (note 1)
32
VDD
11
VDD
33
VSS
12
VSS
34
A14
13
WE
35
VPP
14
DI5/DO5
36
DI3/DO3
15
DI6/DO6
37
DI2/DO2
16
OE
38
DI1/DO1
17
DI4/DO4
39
DI0/DO0
18
A7
40
DI7/DO7
19
A6
41
VSS
20
A5
42
VSS
21
A4
Note
22
A3
1. For driving the oscillator pins see Fig.10c.
1997 Dec 12
67
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
Table 69 Timing table for programming; see Fig.33
SYMBOL
PARAMETER
MIN.
TYP.
MAX.
UNIT
tsu(AW)
address set-up time write
2
−
−
µs
th(AW)
address hold time write
10
−
−
µs
tsu(AR)
address set-up time read
10
−
−
ns
th(AR)
address hold time read
200
−
−
ns
tsu(D)
data set-up time
2
−
−
µs
th(D)
data hold time
20
−
−
µs
tsu(prog)
programming voltage set-up time
10
−
−
µs
th(prog)
programming voltage hold time
10
−
−
µs
tW(prog)
programming pulse width
90
−
−
µs
tW(R)
read pulse width
300
−
−
ns
tACC(OE)
output enable access verify
92
122
183
ns
tDZ(OE)
data float after OE
10
−
−
ns
10 µs
10 µs
handbook, full pagewidth
WE
VIH
VIL
tsu(AW)
address VIH
A0 to A13 V
IL
th(AW)
ADDRESS VALID
tsu(AR)
data in VIH
DI0 to DI7 V
IL
DATA IN VALID
tsu(D)
data out VIH
DO0 to DO7 V
IL
VPP
OE
th(D)
High Z
DATA OUT VALID
tsu(prog)
th(prog)
tDZ(OE)
VPP
VIL
tACC(OE)
tW(R)
VIH
VIL
MGG051
Fig.33 Programming waveforms.
1997 Dec 12
th(AR)
68
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
handbook, full pagewidth
0
x x x x x 010
P83Cx80; P87C380
1
RESET
93 XTAL1
CODE
5 XTAL1
4 XTAL1 4 XTAL1
8 XTAL1
4 XTAL1
XTAL1
MBK517
Fig.34 Timing for OTP Programming/Verification.
23 LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
VDD
supply voltage
4.4
5.5
VI
input voltage (all inputs)
−0.5
VDD + 0.5 V
V
Isource(max)
total maximum source current for all port lines
0.50
0.67
Isink(max)
total maximum sink current for all port lines
155
165
mA
Ptot
total power dissipation
88.4
170
mW
Tstg
storage temperature
−60
+150
°C
Tamb
operating ambient temperature (for all devices)
−25
+85
°C
mA
24 HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is
desirable to take normal precautions appropriate to handling MOS devices (see “Handling MOS devices” ).
1997 Dec 12
69
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
25 DC CHARACTERISTICS
VDD = 4.5 to 5.5 V; VSS = 0 V; Tamb = −25 to +85 °C; all voltages with respect to VSS unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supply
VDD
operating supply voltage
IDD
operating supply current
VPOR
4.4
5
5.5
V
fclk = 12 MHz
20.1
29.4
30.9
mA
fclk = 16 MHz
25.2
36.1
38.4
mA
3.6
3.9
4.2
V
5.5
Power-on-reset voltage level
PROGRAMMING SUPPLY
VDD(P)
supply voltage programming mode
4.4
5.0
VPP
programming voltage
12.0
12.75 13.0
V
V
IDD(P)
supply current programming mode
10.6
19.1
24.0
mA
IPP
programming current
77.8
80.1
81.3
mA
20
60
180
kΩ
±10
µA
RESET
RI(RESET)
input resistance RESET
VDD = 4.5 V to 5.5 V
ILI
input leakage current
VSS < VI < VDD
VIL
LOW-level input voltage
VSS − 0.5
−
0.3VDD
V
VIH
HIGH-level input voltage
0.7VDD
−
VDD + 0.5
V
HSYNCin/PROG and VSYNCin/OE
IIL
Input leakage current
−10
µA
VIL
LOW-level input voltage
VSS − 0.5
−
0.8
V
VIH
HIGH-level input voltage
2.0
−
VDD + 0.5
V
VSS < VI < VDD
CSYNCin/P1.6
ILI
input leakage current
−10
µA
VIL
LOW-level input voltage
VSS − 0.5
−
0.8
V
VIH
HIGH-level input voltage
2.0
−
VDD + 0.5
V
IOL
LOW-level output sink current
IOH
VSS < VI < VDD
VO ≤ 0.4 V
1.6
−
−
mA
VO ≤ 1.0 V
10
−
−
mA
strong pull-up during 2 clock
cycles
VO = VDD − 0.4 V
1.6
−
−
mA
weak pull-up
VO = VDD − 0.4 V
25
−
−
µA
HIGH-level pull-up output source
current
Port 0
VIL
LOW-level input voltage
VSS − 0.5
−
0.3VDD
V
VIH
HIGH-level input voltage
0.7VDD
−
VDD + 0.5
V
ILI
input leakage current
VI = 0.4VDD; VDD = 5 V
−10
−
−100
µA
IIT
input transition current
VI = 0.5VDD; VDD = 5 V
−
−
−1000
µA
IOL
LOW-level output sink current
VO ≤ 0.4 V
1.6
−
−
mA
VO ≤ 1.0 V
10
−
−
mA
1997 Dec 12
70
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
SYMBOL
IOH
PARAMETER
P83Cx80; P87C380
CONDITIONS
MIN.
TYP.
MAX.
UNIT
HIGH-level pull-up output source
current
strong pull-up during 2 clock
cycles
VO = VDD − 0.4 V
1.6
−
−
mA
weak pull-up
VO = VDD − 0.4 V
25
−
−
µA
Port 1: SCL/P1.0, SDA/P1.1, SCL1/P1.2 and SDA1/P1.3
VIL
LOW-level input voltage
VSS − 0.5
−
0.3VDD
V
VIH
HIGH-level input voltage
0.7VDD
−
VDD + 0.5
V
ILI
input leakage current
VI = 0.4VDD; VDD = 5 V
−10
−
−100
µA
IIT
input transition current
VI = 0.5VDD; VDD = 5 V
−
−
−1000
µA
IOL
LOW-level output sink current
VO = 0.4 V; VDD = 5V
3.0
−
−
mA
IOH
HIGH-level pull-up output source
current
strong pull-up during 2 clock
cycles
VO = VDD − 0.4 V
1.6
−
−
mA
weak pull-up
VO = VDD − 0.4 V
25
−
−
µA
Port 1 and 3: VSYNCout/P1.4, HSYNCout/P1.5, PWM10/P1.7 and ADC0/P3.2 to ADC1/P3.3
VIL
LOW-level input voltage
VSS − 0.5
−
0.3VDD
V
VIH
HIGH-level input voltage
0.7VDD
−
VDD + 0.5
V
ILI
input leakage current
VI = 0.4VDD; VDD = 5 V
−10
−
−100
µA
IIT
input transition current
VI = 0.5VDD; VDD = 5 V
−
−
−1000
µA
IOL
LOW-level output sink current
VO ≤ 0.4 V
1.6
−
−
mA
IOH
HIGH-level pull-up output source
current
strong pull-up during 2 clock
cycles
VO = VDD − 0.4 V
1.6
−
−
mA
weak pull-up
VO = VDD − 0.4 V
25
−
−
µA
Port 2 and 3: P2.0/PWM0 to P2.7/PWM7 and Port P3.0/PWM8/CLAMP to P3.1/PWM9/PATOUT
VIL
LOW-level input voltage
VSS − 0.5
−
0.3VDD
V
VIH
HIGH-level input voltage
0.7VDD
−
VDD + 0.5
V
ILI
input leakage current
VI = 0.4VDD; VDD = 5 V
−10
−
−100
µA
IIT
input transition current
VI = 0.5VDD; VDD = 5 V
−
−
−1000
µA
IOL
LOW-level output sink current
VO ≤ 0.4 V
1.6
−
−
mA
IOH
HIGH-level pull-up output source
current
strong pull-up during 2 clock
cycles
VO = VDD − 0.4 V
1.6
−
−
mA
weak pull-up
VO = VDD − 0.4 V
25
−
−
µA
1997 Dec 12
71
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
SYMBOL
PARAMETER
P83Cx80; P87C380
CONDITIONS
MIN.
TYP.
MAX.
UNIT
INT1/VPP
VIL
LOW-level input voltage
VIH
HIGH-level input voltage
VSS − 0.5
IIH = 2 mA
VIH − VDD input voltage with respect to VDD
−
0.2VDD − 0.1 V
0.2VDD + 0.9 −
12.6
V
−
8
V
−
Note
1. This maximum applies at all times, including during power switching, and must be accounted for in power supply
design. During a power-on process, the +12 V source used for external pull-up resistors should not precede the VDD
of the P83C880, P83C180, P83C280 and P83C380 up their respective voltage ramps by more than this margin, nor,
during a power-down process, should VDD precede +12 V down their respective voltage ramps by more than this
margin.
26 DIGITAL-TO-ANALOG CONVERTER CHARACTERISTICS
VDD = 5 V; VDDA = 5 V; Tamb = 27 °C.
SYMBOL
PARAMETER
TEST CONDITION
MIN.
TYP.
MAX.
UNIT
VDD
supply voltage
4.4
−
5.5
V
RESDAC
DAC resolution
−
8
−
bit
Io(DAC)
operating current for each
DAC channel
output pin connected to
VDDA via 40 kΩ
−
−
2.5
mA
Io(DAC)(id)
DAC idle current
all 4 DAC channels
shut-down
−
−
61
µA
Vo(DAC)
DAC output level voltage
output pin open
0
−
VDDA
V
at FFH code input;
IOH = −1mA (note 1)
VDDA − 0.2 −
−
V
at 00H code input;
IOL = 1mA
−
−
0.2
V
output level 0.2 to 4.8 V
−1
−
+1
LSB
DLe
differential non-linearity
tst
settling time
−
−
20
ms
∆Vo(T)
output voltage variation
due to temperature drift
−
−
1.5
mV/°C
∆Vo
output voltage ripple
−
−
2
mV
Ttest > 20 ms
Note
1. The ‘negative’ value denotes that the current is sourcing out from the chip into the load device through the output pin.
1997 Dec 12
72
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
27 AC CHARACTERISTICS
VDD = 4.5 V to 5.5 V; VSS = 0 V; Tamb = −25 to + 85 °C; all voltages with respect to VSS unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
fclk
crystal oscillator frequency
VDD = 5 V
10
12
16
MHz
fPXE
PXE resonator frequency
VDD = 5 V
10
12
16
MHz
CXTAL1
external capacitance at XTAL1
with crystal resonator
−
20
27
pF
with PXE resonator
−
20
27
pF
with crystal resonator
−
20
27
pF
with PXE resonator
−
20
27
pF
V
CXTAL2
external capacitance at XTAL2
Analog-to-Digital Converter (software)
Vin(A)
comparator analog input voltages
ADC0; ADC1
VSS
−
VDD
VAE
conversion error range
−
−
±1⁄2
LSB
tconv(ADC)
conversion time (from any change in
ADC input i.e. voltage level)
−
−
7
µs
DDC1 Mode(1) (transmit-only, unidirectional); see Figs 25 and 35
tDOV
output valid from VCLK
−
−
30
µs
tVCLKH
VCLK high time
20
−
−
µs
tVCLKL
VCLK low time
20
−
−
µs
tt(mode)
mode transition time
−
−
800
ns
tsup(input)
input filter spike suppression; for SDA,
SCL and VSYNC
−
−
200
ns
tsu(DDC1)
DDC1 mode set-up time
−
5
−
µs
Horizontal sync input for the mode detection; see Fig.36
Hfreq
HSYNC input frequency
15
−
150
kHz
tW(HSYNC)
HSYNC input pulse width
notes 2 and 3
0.25
−
8
µs
HDCYC
HSYNC input duty cycle
notes 2 and 3
−
−
25
%
tir(HSYNC)
HSYNC input rise time
−
−
100
ns
tif(HSYNC)
HSYNC input fall time
−
−
100
ns
Vertical Sync Input for the Mode Detection; see Fig.37
Vfreq
VSYNC input frequency
40
−
200
Hz
tW(VSYNC)
VSYNC input pulse width
note 4
1
−
24
note 5
VDCYC
VSYNC input duty cycle
note 4
−
−
25
%
tir(VSYNC)
VSYNC input rise time
−
−
100
ns
tif(VSYNC)
VSYNC input fall time
−
−
100
ns
1997 Dec 12
73
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
SYMBOL
PARAMETER
CONDITIONS
P83Cx80; P87C380
MIN.
TYP.
MAX.
UNIT
Composite Sync Input for the Mode Detection; see Figs 38 and 39
TEQ(CSYNC)
equalizing pulse period for CSYNC
input
−
0.5
−
note 5
tWEQ(CSYNC)
equalizing pulse width for CSYNC
input
−
0.5
−
note 6
NEQ
equalizing pulses plus the VSYNC
interval
−
−
30
note 5
Horizontal and Vertical Pulse Generation; see Figs 40 and 41
TH(free)
horizontal pulse period in free running
10
−
66
µs
tWH(free)
horizontal pulse width in free running
0.4
−
2.5
µs
tor(HSYNC)
HSYNC output pulse rise time
30
31
32
ns
tof(HSYNC)
HSYNC output pulse fall time
24
26
28
ns
td(in-out)(HSYNC)
HSYNC output delay to input
−
−
100
ns
tdmax(HSYNCm)
HSYNC output maximum delay after
missing HSYNC
−
−
350
ns
tW(HSYNCsub)
HSYNC output substitution pulse width
−
−
2.5
µs
0
−
125
ns
td(HSYNC-CLAMP) CLAMP pulse delay to HSYNC input
tW(CLAMP)
CLAMP pulse width
0.4
−
2.5
µs
TV(free)
vertical pulse period in free running
−
−
2048
note 5
tWV(free)
vertical pulse width in free running
−
−
32
note 5
tor(VSYNC)
VSYNC output pulse rise time
22
24
26
ns
tof(VSYNC)
VSYNC output pulse fall time
24
27
30
ns
td(in-out)(VSYNC)
VSYNC output delay to input
−
−
250
ns
tdmax(VSYNCm)
VSYNC output maximum delay after
missing VSYNC
−
−
1
note 5
tW(VSYNCsub)
VSYNC output substitution pulse width
−
−
16
note 5
Slope control port
ttLH(sce)
LOW-to-HIGH transition delay while
slope control enabled
0.1VDD to 0.9VDD; note 7
25
−
100
ns
ttHL(sce)
HIGH-to-LOW transition delay while
slope control enabled
0.9VDD to 0.1VDD; note 7
25
−
100
ns
tPLH(scd)
LOW-to-HIGH propagation delay while 0.1VDD to 0.9VDD;
slope control disabled
load = 50 pF
−
−
10
ns
tPHL(scd)
HIGH-to-LOW propagation delay while 0.9VDD to 0.1VDD;
slope control disabled
load = 50 pF
−
−
10
ns
Notes
1. For the DDC2 Mode (bidirectional I2C-bus mode), refer to the standard I2C-bus specification.
2. The actual sync width has to fulfil both requirements, maximum pulse width tW(HSYNC) = 8.0 µs and maximum duty
cycle HDCYC of 25%, at the same time.
3. The polarity of the horizontal sync pulse is said to be positive if the HIGH period is shorter than the LOW period.
4. The actual sync width has to fulfil both requirements, maximum pulse width tW(VSYNC) = 24 horizontal line periods
and maximum duty cycle VDCYC of 25%, at the same time.
1997 Dec 12
74
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
5. Unit is HSYNC line period: Tline(HSYNC).
6. Unit is HSYNC pulse width: tW(HSYNC).
7. This transition delay has to be loaded independent for capacitances up to 50 pF.
transmit only mode
(DDC1)
handbook, full pagewidth
bidirectional mode
(DDC2)
SCL
tt(mode)
SDA
VCLK
MGG052
Fig.35 Mode transition from DDC1 to DDC2.
handbook, full pagewidth
HSYNC
tif(HSYNC)
tW(HSYNC)
HDCYC
tir(HSYNC)
THSYNC
MGG053
Fig.36 Horizontal sync input signal.
handbook, full pagewidth
VSYNC
tif(VSYNC)
tW(VSYNC)
VDCYC
tir(VSYNC)
TVSYNC
Fig.37 Vertical sync input signal.
1997 Dec 12
75
MGG054
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
handbook, full pagewidth tW(CSYNC)
TEQ(CSYNC)
P83Cx80; P87C380
1/Hfreq
CSYNC
tWEQ(CSYNC)
HSYNC
VSYNC
2nd field
1st field
NEQ
CSYNC
HSYNC
VSYNC
2nd field
MGG055
1st field
Fig.38 Standard composite sync pulse wave forms.
1997 Dec 12
76
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
handbook, full pagewidth
HSYNC
tW(HSYNC)
1/Hfreq
VSYNC
tW(VSYNC)
CSYNC-1
CSYNC-2
tWEQ(CSYNC)
TEQ(CSYNC)
CSYNC-3
CSYNC-4
CSYNC-5
CSYNC-6
NEQ
MGG056
Fig.39 Composite sync pulse wave forms.
1997 Dec 12
77
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
handbook, full pagewidth
HSYNC
HSYNCout
(free running)
tof(HSYNC)
tWH(free)
tor(HSYNC)
TH(free)
HSYNCout
(sync/
substitution)
tdmax(HSYNCm)
td(in-out)(HSYNC)
tW(HSYNCsub)
HSYNCout
(sync/substitution
with fixed pulse
width)
tdmax(HSYNCm)
tW(HSYNCsub)
tW(HSYNCsub)
CLAMP
(clamp pulse
at back porch)
td(HSYNC-CLAMP)
tW(CLAMP)
CLAMP
(clamp pulse
at front porch)
td(HSYNC-CLAMP)
MGG057
tW(CLAMP)
Fig.40 Horizontal sync output pulse.
1997 Dec 12
78
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
handbook, full pagewidth
VSYNC
VSYNCout
(free running)
tof(VSYNC)
tWV(free)
tor(VSYNC)
TV(free)
VSYNCout
(sync/
substitution)
tdmax(VSYNCm)
td(in-out)(VSYNC)
tW(VSYNCsub)
MGG058
Fig.41 Vertical sync output pulse.
1997 Dec 12
79
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
28 PACKAGE OUTLINE
seating plane
SDIP42: plastic shrink dual in-line package; 42 leads (600 mil)
SOT270-1
ME
D
A2
L
A
A1
c
e
Z
b1
(e 1)
w M
MH
b
22
42
pin 1 index
E
1
21
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
5.08
0.51
4.0
1.3
0.8
0.53
0.40
0.32
0.23
38.9
38.4
14.0
13.7
1.778
15.24
3.2
2.9
15.80
15.24
17.15
15.90
0.18
1.73
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
90-02-13
95-02-04
SOT270-1
1997 Dec 12
EUROPEAN
PROJECTION
80
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
29 SOLDERING
29.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
29.3
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
1997 Dec 12
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
29.2
P83Cx80; P87C380
81
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
P83Cx80; P87C380
30 DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
31 LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
32 PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
1997 Dec 12
82
Philips Semiconductors
Product specification
Microcontrollers for monitors with DDC
interface, auto-sync detection and sync proc.
NOTES
1997 Dec 12
83
P83Cx80; P87C380
Philips Semiconductors – a worldwide company
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010,
Fax. +43 160 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 0044
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580920
France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Band Box Building, 2nd floor,
254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025,
Tel. +91 22 493 8541, Fax. +91 22 493 0966
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Al. Vicente Pinzon, 173, 6th floor,
04547-130 SÃO PAULO, SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 821 2382
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors,
International Marketing & Sales Communications, Building BE-p,
P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Internet: http://www.semiconductors.philips.com
© Philips Electronics N.V. 1997
SCA56
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
457041/1200/01/pp84
Date of release: 1997 Dec 12
Document order number:
9397 750 03171