PanelMatch™ I N T E G R A T E D P R O D U C T S LXM1623-12-44 12V Dual 4W CCFL Programmable Inverter Module P RODUCTION D ATASHEET KEY FEATURES DESCRIPTION Externally Programmable Maximum Output Current Easy to Use Brightness Control RangeMAX Wide Range Dimming Output Open & Short-Circuit Protection and Automatic StrikeVoltage Regulation and Timeout Fixed Frequency Operation Rated From -20 to 70°C bs ol et e RangeMAX™ Digital Dimming Technique provides flicker-free brightness control in any wide range (typically 50:1+) dimming application. The resultant “burst drive” that energizes the lamp is designed specifically to ensure that no premature lamp degradation occurs, while allowing significant power savings at lower dim levels. The modules convert DC voltage from the system battery or AC adapter directly to high frequency, high-voltage waves required to ignite and operate CCFL lamps. A 5V input inverter is also available: LXM1623-05-44. The modules design utilizes Microsemi’s LX1689 backlight controller, which provides a number of cost and performance advantages due to the controller’s high level of integration. Other benefits of this new topology are stable fixed-frequency operation, secondary-side strike-voltage regulation and both open/shorted lamp protection with fault timeout. APPLICATIONS LCD’s Requiring Both Output Connectors on One Side of Panel Sharp LQ104S1DG21/51 and LQ121S1DG31/41 Samsung LTM121SI-T01 Desktop Displays Industrial Display Controls WWW . Microsemi .C OM The LXM1623-12-44 is a Dual 4W Output Direct Drive™ CCFL (Cold Cathode Fluorescent Lamp) Inverter Module specifically designed to be compatible with the Sharp LQ104S1DG21 / 15 10.4”, LQ121S1DG31 / 41 12.1” as well as the Samsung LTM121SI-T01 12.1” or similar dual lamp displays that have both individual lamp output connectors on the top side of the panel. LXM1623 modules provide the designer with a vastly superior display brightness range. This brightness range is achievable with virtually any LCD display. The modules are available with a dimming input that permits brightness control from either, a DC voltage source, a PWM signal or external Potentiometer. The maximum output current is externally programmable (through the input connector) over a range of 5.2 to 6.7mA in 0.5mA steps. This allows the inverter to match the panel’s lamp current specifications, or it can be used to purposely drive the lamps at a lower current to save power or lower nominal brightness. BENEFITS Smooth, Flicker Free 2%-100% Full-Range Brightness Control Programmable Output Current Allows Inverter to Mate With a Wide Variety of LCD Panel’s Specifications Output Open Circuit Voltage Regulation Minimizes Corona Discharge For High Reliability IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com Protected By U.S. Patents: 5,923,129; 5,930,121; 6,198,234; Patents Pending PRODUCT HIGHLIGHT UNIVERSAL DIMMING INPUT PWM Signal W W Potentiometer 2 3 1 2 3 DC Voltage Source SELECTABLE MAXIMUM OUTPUT CURRENT 5.2MA TO 6.7MA RMS PACKAGE ORDER INFO PART NUMBER OUTPUT CONNECTOR LXM1623-12-44 JST SM02(8.0)B-BHS-1-TB or Yeon Ho 20015WR-05A00 Copyright © 2003 Rev. 1.0a, 2005-01-17 INVERTER MATES DIRECTLY TO PANEL CONNECTORS JST BHR-03VS-1 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 LXM1623-12-44 O VDC, OR POTENTIOMETER 1 "PWM", PanelMatch™ I N T E G R A T E D LXM1623-12-44 12V Dual 4W CCFL Programmable Inverter Module P R O D U C T S P RODUCTION D ATASHEET bs ol et e Input Signal Voltage (VIN1).....................................................................................................................................-0.3V to 16V Input Power ....................................................................................................................................................................... 10W Output Voltage, no load ............................................................................................................ Internally Limited to 1800VRMS Output Current ............................................................................................................................7.5mARMS (Internally Limited) Output Power (each output) ............................................................................................................................................. 4.0W Input Signal Voltage ( SLEEP Input) ...................................................................................................................... -0.3V to VIN1 Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C Operating Relative Humidity, non-condensing ................................................................................................................ ≤ 90% Storage Temperature Range...............................................................................................................................-40°C to 85°C Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. WWW . Microsemi .C OM ABSOLUTE MAXIMUM RATINGS (NOTE 1) RECOMMENDED OPERATING CONDITIONS (R.C.) This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond which the inverter, although operational, will not function optimally. Parameter Symbol Input Supply Voltage Range (Fully Regulated Lamp Current) Input Supply Voltage Range (Functional) Output Power (each output) Linear BRITE Control Input Voltage Range Lamp Operating Voltage Lamp Current (Full Brightness) Operating Ambient Temperature Range VIN1 PO VBRT_ADJ VLAMP IOLAMP TA Recommended Operating Conditions Min R.C. Max 10.8 12 13.2 10.2 12 3.5 14.4 4.0 2.0 610 6.7 70 0.5 450 5.2 -20 530 Units V W V VRMS mARMS °C ELECTRICAL CHARACTERISTICS Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of 25°C except where otherwise noted. Parameter Test Conditions LXM1623-12-44 Min Typ Max Units OUTPUT PIN CHARACTERISTICS Full Bright Lamp Current (each output) IL(MAX) Full Bright Lamp Current (each output) IL(MAX) Full Bright Lamp Current (each output) IL(MAX) Full Bright Lamp Current (each output) IL(MAX) Output Current Lamp to Lamp Deviation ILL%DEV Min. Average Lamp Current (each output) Lamp Start Voltage Operating Frequency Burst Frequency Copyright © 2003 Rev. 1.0a, 2005-01-17 IL(MIN) VLS fO fBURST VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Ground, ISET2 = Ground VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Ground, ISET2 = Open VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Open, ISET2 = Ground VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Open, ISET2 = Open VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = Open, ISET2 = Open VBRT_ADJ ≤0.5VDC, SLEEP > 2.0V, VIN1 = 12VDC ISET1 = ISET2 = Ground -20°C < TA < 70°C, VIN1 > 10.8VDC 1450 VBRT_ADJ = 2.5VDC, SLEEP > 2.0V, VIN1 = 12V Output Burst Frequency 57 60 63 kHz 222 234 246 Hz 4.7 5.2 5.7 mARMS 5.2 5.7 6.2 mARMS 5.7 6.2 6.7 mARMS 6.2 6.7 7.2 mARMS 3 10 % Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 0.30 mARMS 1600 VRMS Page 2 ELECTRICALS O ` Symbol PanelMatch™ I N T E G R A T E D P R O D U C T S LXM1623-12-44 12V Dual 4W CCFL Programmable Inverter Module P RODUCTION D ATASHEET Parameter ` Symbol ` Units IBRT -300 50 µADC µADC VBRT_ADJ = 0VDC VBRT_ADJ = 3VDC Minimum Input for Max. Lamp Current VBRT_ADJ IO(LAMP) = Maximum Lamp Current Maximum Input for Min. Lamp Current VBRT_ADJ IO(LAMP) = Minimum Lamp Current 2.0 2.05 bs ol et e ` LXM1623-12-44 Min Typ Max BRITE INPUT Input Current ` Test Conditions 0.4 0.5 VDC VDC SLEEP INPUT RUN Mode VSLEEP 2.0 VIN1 VDC SLEEP Mode VSLEEP -0.3 0.8 VDC 0.4 V WWW . Microsemi .C OM ELECTRICAL CHARACTERISTICS (CONTINUED) Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of 25°C except where otherwise noted. SET1,2 INPUT SET1,2 Low Threshold VL Input Current ISET VSET ≤ 0.4V -300 µA POWER CHARACTERISTICS Sleep Current IIN(MIN) Run Current IIN(RUN) Efficiency η VIN1 = 12VDC, SLEEP < 0.8V 0.0 VIN1 = 12VDC, SLEEP ≥ 2.0V, ISET1 = Open ISET2 = Ground, VLAMP = 500VRMS VIN1 = 12VDC, SLEEP ≥ 2.0V, ISET1 = Open ISET2 = Ground, VLAMP = 500VRMS 10 50 µADC 550 mADC 90 % FUNCTIONAL PIN DESCRIPTION CONN PIN DESCRIPTION CN1 (Molex 53261-0890) Mates with 51021-0800 housing, 50079-8100 pins. Mates with LX9501 input cable assembly CN1-1 CN1-2 CN1-3 CN1-4 Main Input Power Supply (10.8V < VIN1 < 13.2V) GND Power Supply Return SLEEP ON/OFF Control. (0V < SLEEP < 0.8 = OFF, SLEEP >= 2.0V = ON O CN1-5 VIN1 CN1-6 BRITE CN1-7 SET1 SET1 MSB Connecting this pin to ground decreases the output current (see Table 1) Brightness Control (0.5V to 2.0VDC). 2.0VDC gives maximum lamp current. CN1-8 SET2 SET2 LSB Connecting this pin to ground decreases the output current (see Table 1) CN2-1 CN3-1 VHI High voltage connection to high Side of lamp. Connect to lamp terminal with shortest lead length. DO NOT connect to Ground. CN2-2 CN3-2 VLO Connection to low side of lamp. Connect to lamp terminal with longer lead length. DO NOT connect to Ground Copyright © 2003 Rev. 1.0a, 2005-01-17 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 ELECTRICALS CN2, CN3 for LXM1623-12-44 (JST SM02(8.0)B-BHS-1-TB or Yeon Ho 20015WR-05A00) PanelMatch™ I N T E G R A T E D LXM1623-12-44 12V Dual 4W CCFL Programmable Inverter Module P R O D U C T S P RODUCTION D ATASHEET WWW . Microsemi .C OM TABLE 1 OUTPUT CURRENT SETTINGS SET1 (Pin 7) Open* Open* Ground Ground SET2 (Pin 8) Open* Ground Open* Ground Nominal Output Current 6.7mA 6.2mA 5.7mA 5.2mA bs ol et e * If driven by a logic signal it should be open collector or open drain only, not a voltage source. PHYSICAL DIMENSIONS LXM1623-12-44 108.7mm 4.28in. 10.5mm 85.75mm ±0.2mm 0.413in. 3.375in. 0.765in. CN1 W W 19.45mm W 12.7mm ±0.2mm 22.35mm 0.500in. 0.88in. 6.75mm 0.266in. 3.05MM X 2 DIA. ±0.08 GROUNDED MOUNTING HOLE PLASTIC SCREW REQUIRED 6MM SCREW HEAD CLEARANCE Weight: PCB Tolerance ±0.5mm Warning High Voltage Present at high 10.2mm Max side of transformer 0.402in. and Output (18g) typ. Connectors Dimensions are in millimeters (inches are for reference only) SIMPLIFIED BLOCK DIAGRAM High Voltage Transformer Controller V BRITE 10K Comparator Ramp +3V - Transformer Driver Ramp Gen V HI V IN1 V HI OV SENSE PACKAGE DATA O + 0.5 2V DC V HI LAMP2 +3V SET 1 SET 2 Z OC SENSE +3V 10K ISENSE Z LAMP1 10K V LO Z V LO Copyright © 2003 Rev. 1.0a, 2005-01-17 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 PanelMatch™ I N T E G R A T E D P R O D U C T S LXM1623-12-44 12V Dual 4W CCFL Programmable Inverter Module P RODUCTION D ATASHEET 12V DAC or Pot The brightness control may be a voltage output DAC or other voltage source, a digital pot or 20K manual pot. The inverter contains an internal 10K pull-up to 3V to bias the pot, add a 1.8K resistor to set the lower threshold voltage. A 3.3V Logic Level PWM signal from a micro-controller may also be used as shown in Figure 1A. If you need to turn the inverter ON/OFF remotely, connect to TTL logic signal to the SLEEP input. VIN1 BRITE 0.45V 20K to 2.0V VHI LXM1623-12-44 CCFL TUBE bs ol et e 1.8K SLEEP SET1 SET2 GND VLO ONE OF TWO Connect VHI to high voltage wire from the lamp. Connect VLO to the low voltage wire (wire with thinner insulation). Never connect VLO to circuit ground as this will defeat lamp current regulation. If both lamp wires have heavy high voltage insulation, connect the longest wire to VLO. This wire is typically white. Use the SET1 and SET2 (see Figure 2) inputs to select the desired maximum output current. Using these two pins in combination allows the inverter to match a wide variety of panels from different manufactures. Generally the best lamp lifetime correlates with driving the CCFL at the manufactures nominal current setting. However the SET1 and SET2 inputs allow the user the flexibility to adjust the current to the maximum allowable output current to increase panel brightness at the expense of some reduced lamp life. Although the SET pins are designed such that just leaving them open or grounding them is all that is needed to set the output current, they can also be actively set. Using a open collector or open drain logic signal will allow you to reduce the lamp current for situations where greater dim range is required, as an example in nighttime situations. In conjunction with a light sensor or other timer the panel could be set to higher brightness (maximum output current) for daytime illumination and lower brightness (minimum or typical output current) at nighttime. Since the dim ratio is a factor of both the burst duty cycle and the peak output current, using this technique the effective dim ratio can be increased greater than the burst duty cycle alone. Conversely, the SET inputs could be used to overdrive the lamp temporarily to facilitate faster lamp warm up at initial lamp turn on. Of course, any possible degradation on lamp life from such practices is the users responsibility since not all lamps are designed to be overdriven. The inverter has a built in fault timeout function. If the output is open (lamp disconnected or broken) or shorted to ground the inverter will attempt to strike the lamp for several seconds. After about 3 seconds without success the inverter will shutdown. In order to restart the inverter it is necessary to toggle the sleep input or cycle the VIN1 input supply NC NC Figure 1 – Brightness Control (Output current set to maximum) PWM Signal from System BRITE P.W. LXM1623-12-44 2.5us to 125uS 0 < P.W. < 100% of period Figure 1A – PWM Brightness Control 12V VIN1 VHI O BRITE CCFL TUBE LXM1623-12-44 SLEEP SET1 L L H H SET2 GND VLO ONE OF TWO L 5.2mARMS H 5.7mARMS L 6.2mARMS H 6.7mARMS L=GND; H=Open Figure 2 – Max Output Current (SET1 and SET2 Inputs) Copyright © 2003 Rev. 1.0a, 2005-01-17 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5 APPLICATION WWW . Microsemi .C OM TYPICAL APPLICATION PanelMatch™ I N T E G R A T E D P R O D U C T S LXM1623-12-44 12V Dual 4W CCFL Programmable Inverter Module P RODUCTION D ATASHEET O bs ol et e WWW . Microsemi .C OM NOTES NOTES PRODUCTION DATA – Information contained in this document is proprietary to Microsemi and is current as of publication date. This document may not be modified in any way without the express written consent of Microsemi. Product processing does not necessarily include testing of all parameters. Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. PRODUCTION DATA – Information contained in this document is proprietary to Copyright © 2003 Rev. 1.0a, 2005-01-17 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6 PanelMatch™ I N T E G R A T E D P R O D U C T S LXM1623-12-44 12V Dual 4W CCFL Programmable Inverter Module P RODUCTION D ATASHEET O bs ol et e WWW . Microsemi .C OM Microsemi and is current as of publication date. This document may not be modified in any way without the express written consent of Microsemi. Product processing does not necessarily include testing of all parameters. Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. Copyright © 2003 Rev. 1.0a, 2005-01-17 Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 7