MICROSEMI LXM1617-05-63

PanelMatch™
I N T E G R A T E D
LXM1617-05-6x
5V 6W CCFL Programmable Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
KEY FEATURES
DESCRIPTION
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
ƒ Externally Programmable
Maximum Output Current
ƒ Easy to Use Brightness
Control
ƒ Output Short-Circuit Protection
and Automatic Strike-Voltage
ƒ RangeMAX Wide Range
Dimming
ƒ Regulation and Timeout Rated
From –20 to 70° C
ƒ UL60950 L175910
APPLICATIONS
WWW . Microsemi .C OM
The resultant “burst drive” that
energizes the lamp was designed
specifically to ensure that no premature
lamp degradation occurs, while allowing
significant power savings at lower dim
levels.
The modules convert DC voltage from
the system battery or AC adapter directly
to high frequency, high-voltage waves
required to ignite and operate CCFL
lamps. A 12V input inverter is also
available (LXM1617-12-6x).
The modules design is based on
Microsemi’s new LX1689 backlight
controller, which provides a number of
cost and performance advantages due to
the controller’s high level of integration.
Other benefits of this new topology
are stable fixed-frequency operation,
secondary-side strike-voltage regulation
and both open/shorted lamp protection
with fault timeout.
The LXM1617-05-6x is a Single
Output 6W Direct Drive™ CCFL (Cold
Cathode Fluorescent Lamp) Inverter
Module specifically designed for driving
LCD backlight lamps. It is ideal for
driving typical 12.1” to 15” TFT panels.
LXM1617 modules provide the
designer with a vastly superior display
brightness range. This brightness range is
achievable with virtually any LCD display.
The maximum output current is
externally programmable over a range of 5
to 8mA in 1mA steps to allow the inverter
to properly match to a wide array of LCD
panel lamp current specifications. The
modules include a dimming input that
permits brightness control from a dc
voltage source, a PWM signal or an
external potentiometer.
RangeMAX
Digital
Dimming
Technique provides flicker-free brightness
control in any wide range typically (50:1+)
dimming application.
ƒ Notebook And Sub-Notebook
Computers
ƒ Portable Instrumentation
ƒ Desktop Displays
ƒ Industrial Display Controls
BENEFITS
ƒ Smooth, Flicker Free 2%-100%
Full-Range Brightness Control
ƒ Programmable output current
allows inverter to mate with a
wide variety of LCD panel’s
specifications
ƒ Output Open Circuit Voltage
Regulation Minimizes Corona
Discharge For High Reliability
PRODUCT HIGHLIGHT
U N IV E R S A L D IM M IN G IN P U T
"P W M ", V
DC Voltage
Source
,
OR
P O T E N T IO M
ETER
PW M
Signal
3
Potentiom eter
DC
1
2
LXM1617-05-6X
S ELECTABLE M
8MA
A X IM U M
O
UPUT
C
URRENT
5MA
W
TO
RMS
PACKAGE ORDER INFO
PART NUMBER
LXM1617-05-61
LXM1617-05-62
LXM1617-05-63
Copyright  2002
Rev. 1.0, 2003-10-14
INVERTER MATES DIRECTLY TO
PANEL CONNECTORS
JST SM02(8.0)B-BHS-1-TB JST BHR-03VS-1
JST SM02B-BHSS-1-TB
JST BHSR-02VS-1
Honda QZ-19-A3MYL #02
HONDA QZ-19-3F01
OUTPUT CONNECTOR
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1
PanelMatch™
I N T E G R A T E D
LXM1617-05-6x
5V 6W CCFL Programmable Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
Input Signal Voltage (VIN1)....................................................................................................................................-0.3V to 6.5V
Input Power .................................................................................................................................................................... 8.25W
Output Voltage, no load ............................................................................................................ Internally Limited to 1800VRMS
Output Current .............................................................................................................................10mARMS (Internally Limited)
Output Power ................................................................................................................................................................... 6.0W
Input Signal Voltage ( SLEEP Input) ....................................................................................................................-0.3V to 5.5V
Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V
Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C
Storage Temperature Range...............................................................................................................................-40°C to 85°C
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
terminal.
WWW . Microsemi .C OM
ABSOLUTE MAXIMUM RATINGS (NOTE 1)
RECOMMENDED OPERATING CONDITIONS (R.C.)
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Parameter
Symbol
Input Supply Voltage Range (Fully Regulated
Lamp Current)
Input Supply Voltage Range (Functional)
Output Power
Linear BRITE Control Input Voltage Range
Lamp Operating Voltage
Lamp Current (Full Brightness)
Operating Ambient Temperature Range
VIN1
PO
VBRT_ADJ
VLAMP
IOLAMP
TA
Recommended Operating Conditions
Min
R.C.
Max
4.75
5
5.25
4.5
5
0.5
545
5
-20
2.0
640
5.5
6.0
VIN
735*
8
70
Units
V
W
V
VRMS
mARMS
°C
* Total output power must not exceed 6W. Higher voltage lamps may require maximum output current to be set lower than 8mARMS
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
Parameter
`
Symbol
Test Conditions
LXM1617-05-6x
Min
Typ
Max
Units
OUTPUT PIN CHARACTERISTICS
IL(MAX)
Full Bright Lamp Current
IL(MAX)
Full Bright Lamp Current
IL(MAX)
Full Bright Lamp Current
IL(MAX)
Min. Average Lamp Current
Lamp Start Voltage
Operating Frequency
Burst Frequency
Copyright  2002
Rev. 1.0, 2003-10-14
IL(MIN)
VLS
fO
fBURST
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Ground, ISET2 = Ground
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Ground, ISET2 = Open
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Open, ISET2 = Ground
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = Open, ISET2 = Open
VBRT_ADJ ≤0.5VDC, SLEEP > 2.0V, VIN1 = 5VDC
ISET1 = ISET2 = Ground
-20°C < TA < 70°C, VIN1 > 4.5VDC
VBRT_ADJ = 2.5VDC, SLEEP > 2.0V, VIN1 = 5V
Output Burst Frequency
4.4
5
5.6
mARMS
5.4
6
6.6
mARMS
6.4
7
7.6
mARMS
7.4
8
8.6
mARMS
0.30
mARMS
1400
1650
57
60
63
kHz
222
234
246
Hz
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
VRMS
Page 2
ELECTRICALS
Full Bright Lamp Current
PanelMatch™
I N T E G R A T E D
LXM1617-05-6x
5V 6W CCFL Programmable Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
Parameter
`
Symbol
`
`
LXM1617-05-6x
Min
Typ
Max
Units
-300
50
µADC
µADC
BRITE INPUT
Input Current
`
Test Conditions
IBRT
VBRT_ADJ = 0VDC
VBRT_ADJ = 2.5VDC
Minimum Input for Max. Lamp Current
VBRT_ADJ
IO(LAMP) = Maximum Lamp Current
Maximum Input for Min. Lamp Current
VBRT_ADJ
IO(LAMP) = Minimum Lamp Current
2.0
0.4
2.05
0.5
VDC
VDC
SLEEP INPUT
RUN Mode
VSLEEP
2.0
VIN1
VDC
SLEEP Mode
VSLEEP
-0.3
0.8
VDC
0.4
V
WWW . Microsemi .C OM
ELECTRICAL CHARACTERISTICS (CONTINUED)
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
SET1,2 INPUT
SET1,2 Low Threshold
VL
Input Current
ISET
VSET ≤ 0.5V
-300
µA
POWER CHARACTERISTICS
Sleep Current
IIN(MIN)
Run Current
IRUN
η
Efficiency
VIN1 = 5VDC, SLEEP < 0.8V
0.0
VIN1 = 5VDC, SLEEP ≥ 2.0V, ISET1 = Open
ISET2 = Ground, VLAMP = 640VRMS
VIN1 = 5VDC, SLEEP ≥ 2.0V, ISET1 = Open
ISET2 = Ground, VLAMP = 640VRMS
5
50
µADC
1090
mADC
85
%
FUNCTIONAL PIN DESCRIPTION
CONN
PIN
DESCRIPTION
CN1 (Molex 53261-0890) Mates with 51021-0800 housing, 50079-8100 pins. Mates with LX9501 input cable assembly
CN1-1
CN1-2
CN1-3
CN1-4
VIN1
Main Input Power Supply (4.75V < VIN1 < 5.25V)
GND
Power Supply Return
CN1-5
SLEEP
ON/OFF Control. (0V < SLEEP < 0.8 = OFF, SLEEP >= 2.0V = ON
CN1-6
BRITE
Brightness Control (0.5V to 2.0VDC). 2.0VDC gives maximum lamp current.
CN1-7
SET1
SET1 MSB Connecting this pin to ground decreases the output current (see Table 1)
CN1-8
SET2
SET2 LSB Connecting this pin to ground decreases the output current (see Table 1)
CN2-1
VHI
High voltage connection to high Side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
CN2-2
VLO
Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground
CN2 for LXM1617-05-63 (Honda QZ-19-A3MYL#02)
CN2-3
VHI
High voltage connection to high side of lamp. Connect to lamp terminal with shortest lead length.
DO NOT connect to Ground.
CN2-1
VLO
Connection to low side of lamp. Connect to lamp terminal with longer lead length.
DO NOT connect to Ground
Copyright  2002
Rev. 1.0, 2003-10-14
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
ELECTRICALS
CN2 for LXM1617-05-61 and -62 (JST SM02(8.0)B-BHS-1-TB or SM02B-BHSS-1-TB)
PanelMatch™
I N T E G R A T E D
LXM1617-05-6x
5V 6W CCFL Programmable Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
WWW . Microsemi .C OM
TABLE 1 SETTING OUTPUT CURRENT
OUTPUT CURRENT SETTINGS
SET1
(Pin 7)
Open*
Open*
Ground
Ground
SET2
(Pin 8)
Open*
Ground
Open*
Ground
Nominal Output Current
8.0mA
7.0mA
6.0mA
5.0mA
* If driven by a logic signal it should be open collector or open drain only, not a voltage source.
PHYSICAL DIMENSIONS
LXM1617-05-6X
100mm
3.94in.
85mm
CN-1
-01
MOUNTING HOLE
2.44MM ±.08 DIA.
3.35in
-02
16mm
X
W
0.63in.
12.5mm
9mm ±0.2
W
CN-2
0.492in
SM02(8.0)B-BHS-1-TB
(JST)
0.354in.
3.5mm
0.138in.
11mm
-03
74mm ±0.2mm
GROUNDED MOUNTING
HOLE 2.44MM ±.08 DIA.
Warning
2.91in
High Voltage Present at
high side of Transformer
and Output Connector
0.433in.
1.0mm
0.0394in.
7.5mm Max
0.295in.
PCB tolerances ± 0.2mm , M2 or 2-56 recommended mounting screws
R1.0
SM02B-BHSS-1-TB
(JST)
Honda QZ-19-A3MYL
#02
Weight: (9g) typ.
All dimensions are in millimeters, inches for reference only
SIMPLIFIED BLOCK DIAGRAM
High Voltage
Transformer
Controller
VBRITE
10K
Comparator
+
0.5 2VDC
Ramp
-
Ramp
Gen
VIN1
OCSENSE
PACKAGE DATA
+3V
Transformer
Driver
VHI
LAMP
+3V
10K
SET1
SET2
+3V
OVSENSE
10K
ISENSE
VLO
LXM1617 family
Copyright  2002
Rev. 1.0, 2003-10-14
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 4
PanelMatch™
I N T E G R A T E D
LXM1617-05-6x
5V 6W CCFL Programmable Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
5V
DAC or
Pot
ƒ
If you need to turn the inverter ON/OFF remotely, connect
to TTL logic signal to the SLEEP input.
ƒ
Connect VHI to high voltage wire from the lamp. Connect
VLO to the low voltage wire (wire with thinner insulation).
Never connect VLO to circuit ground as this will defeat
lamp current regulation. If both lamp wires have heavy
high voltage insulation, connect the longest wire to VLO.
This wire is typically white.
ƒ
Use the SET1 and SET2 (see Figure 2) inputs to select the
desired maximum output current. Using these two pins in
combination allows the inverter to match a wide variety of
panels from different manufactures. Generally the best
lamp lifetime correlates with driving the CCFL at the
manufactures nominal current setting. However the SET1
and SET2 inputs allow the user the flexibility to adjust the
current to the maximum allowable output current to
increase panel brightness at the expense of some reduced
lamp life.
ƒ
Although the SET pins are designed such that just leaving
them open or grounding them is all that is needed to set the
output current, they can also be actively set. Using a open
collector or open drain logic signal will allow you to
reduce the lamp current for situations where greater dim
range is required, as an example in nighttime situations. In
conjunction with a light sensor or other timer the panel
could be set to higher brightness (maximum output
current) for daytime illumination and lower brightness
(minimum or typical output current) at nighttime. Since
the dim ratio is a factor of both the burst duty cycle and the
peak output current, using this technique the effective dim
ratio can be increased greater than the burst duty cycle
alone. Conversely the SET inputs could be used to
overdrive the lamp temporarily to facilitate faster lamp
warm up at initial lamp turn on. Of course any possible
degradation on lamp life from such practices is the users
responsibility since not all lamps are designed to be
overdriven.
ƒ
The inverter has a built in fault timeout function. If the
output is open (lamp disconnected or broken) or shorted
the inverter will attempt to strike the lamp for several
seconds. After about 2 to 4 seconds without success the
inverter will shutdown. In order to restart the inverter it is
necessary to toggle the sleep input or cycle the VIN1 input
supply.
VHI
LXM1617-05-6x
1.8K
SLEEP
SET1
SET2
GND
CCFL
TUBE
VLO
NC
NC
Figure 1 – Brightness Control
(output current set to maximum)
PWM Signal
from System
BRITE
P.W.
LXM1617-05-6x
10us to 125uS
0 < P.W. < 100% of period
Figure 1A – PWM Brightness Control
5V
VIN1
BRITE
VHI
CCFL
TUBE
LXM1617-05-6x
SLEEP
SET1
L
L
H
H
SET2
GND
VLO
L
5.0mARMS
H
6.0mARMS
L
7.0mARMS
H
8.0mARMS
L=GND; H=Open
Figure 2 – Max Output Current
(SET1 and SET2 Inputs)
Copyright  2002
Rev. 1.0, 2003-10-14
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5
APPLICATION
The brightness control may be a voltage output DAC or
other voltage source, a digital pot or 20K manual pot. The
inverter contains an internal 10K pull-up to 3V to bias the
pot add a 1.8K resistor to set the lower threshold voltage.
A 3.3V Logic Level PWM signal from a micro-controller
may also be used as shown in Figure 1A.
VIN1
BRITE
0.45V
20K
to
2.0V
ƒ
WWW . Microsemi .C OM
TYPICAL APPLICATION
PanelMatch™
I N T E G R A T E D
LXM1617-05-6x
5V 6W CCFL Programmable Inverter Module
P R O D U C T S
P RODUCTION D ATASHEET
NOTES
WWW . Microsemi .C OM
NOTES
PRODUCTION DATA – Information contained in this document is proprietary to
Microsemi and is current as of publication date. This document may not be modified in
any way without the express written consent of Microsemi. Product processing does not
necessarily include testing of all parameters. Microsemi reserves the right to change the
configuration and performance of the product and to discontinue product at any time.
Copyright  2002
Rev. 1.0, 2003-10-14
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 6