ATMEL AT91SAM7X512-AU

www.DataSheet4U.com
Features
• Incorporates the ARM7TDMI® ARM® Thumb® Processor
•
•
•
•
•
•
•
•
•
•
•
– High-performance 32-bit RISC Architecture
– High-density 16-bit Instruction Set
– Leader in MIPS/Watt
– EmbeddedICE™ In-circuit Emulation, Debug Communication Channel Support
Internal High-speed Flash
– 512 Kbytes (AT91SAM7X512) Organized in Two Banks of 1024 Pages of
256 Bytes (Dual Plane)
– 256 Kbytes (AT91SAM7X256) Organized in 1024 Pages of 256 Bytes (Single Plane)
– 128 Kbytes (AT91SAM7X128) Organized in 512 Pages of 256 Bytes (Single Plane)
– Single Cycle Access at Up to 30 MHz in Worst Case Conditions
– Prefetch Buffer Optimizing Thumb Instruction Execution at Maximum Speed
– Page Programming Time: 6 ms, Including Page Auto-erase,
Full Erase Time: 15 ms
– 10,000 Write Cycles, 10-year Data Retention Capability,
Sector Lock Capabilities, Flash Security Bit
– Fast Flash Programming Interface for High Volume Production
Internal High-speed SRAM, Single-cycle Access at Maximum Speed
– 128 Kbytes (AT91SAM7X512)
– 64 Kbytes (AT91SAM7X256)
– 32 Kbytes (AT91SAM7X128)
Memory Controller (MC)
– Embedded Flash Controller, Abort Status and Misalignment Detection
Reset Controller (RSTC)
– Based on Power-on Reset Cells and Low-power Factory-calibrated Brownout
Detector
– Provides External Reset Signal Shaping and Reset Source Status
Clock Generator (CKGR)
– Low-power RC Oscillator, 3 to 20 MHz On-chip Oscillator and one PLL
Power Management Controller (PMC)
– Power Optimization Capabilities, Including Slow Clock Mode (Down to 500 Hz) and
Idle Mode
– Four Programmable External Clock Signals
Advanced Interrupt Controller (AIC)
– Individually Maskable, Eight-level Priority, Vectored Interrupt Sources
– Two External Interrupt Sources and One Fast Interrupt Source, Spurious Interrupt
Protected
Debug Unit (DBGU)
– 2-wire UART and Support for Debug Communication Channel interrupt,
Programmable ICE Access Prevention
Periodic Interval Timer (PIT)
– 20-bit Programmable Counter plus 12-bit Interval Counter
Windowed Watchdog (WDT)
– 12-bit key-protected Programmable Counter
– Provides Reset or Interrupt Signals to the System
– Counter May Be Stopped While the Processor is in Debug State or in Idle Mode
Real-time Timer (RTT)
– 32-bit Free-running Counter with Alarm
– Runs Off the Internal RC Oscillator
AT91 ARM
Thumb-based
Microcontrollers
AT91SAM7X512
AT91SAM7X256
AT91SAM7X128
Summary
Preliminary
NOTE: This is a summary document.
The complete document is available on
the Atmel website at www.atmel.com.
6120DS–ATARM–03-Oct-06
• Two Parallel Input/Output Controllers (PIO)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
– Sixty-two Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os
– Input Change Interrupt Capability on Each I/O Line
– Individually Programmable Open-drain, Pull-up Resistor and Synchronous Output
Thirteen Peripheral DMA Controller (PDC) Channels
One USB 2.0 Full Speed (12 Mbits per second) Device Port
– On-chip Transceiver, 1352-byte Configurable Integrated FIFOs
One Ethernet MAC 10/100 base-T
– Media Independent Interface (MII) or Reduced Media Independent Interface (RMII)
– Integrated 28-byte FIFOs and Dedicated DMA Channels for Transmit and Receive
One Part 2.0A and Part 2.0B Compliant CAN Controller
– Eight Fully-programmable Message Object Mailboxes, 16-bit Time Stamp Counter
One Synchronous Serial Controller (SSC)
– Independent Clock and Frame Sync Signals for Each Receiver and Transmitter
– I²S Analog Interface Support, Time Division Multiplex Support
– High-speed Continuous Data Stream Capabilities with 32-bit Data Transfer
Two Universal Synchronous/Asynchronous Receiver Transmitters (USART)
– Individual Baud Rate Generator, IrDA® Infrared Modulation/Demodulation
– Support for ISO7816 T0/T1 Smart Card, Hardware Handshaking, RS485 Support
– Full Modem Line Support on USART1
Two Master/Slave Serial Peripheral Interfaces (SPI)
– 8- to 16-bit Programmable Data Length, Four External Peripheral Chip Selects
One Three-channel 16-bit Timer/Counter (TC)
– Three External Clock Inputs, Two Multi-purpose I/O Pins per Channel
– Double PWM Generation, Capture/Waveform Mode, Up/Down Capability
One Four-channel 16-bit Power Width Modulation Controller (PWMC)
One Two-wire Interface (TWI)
– Master Mode Support Only, All Two-wire Atmel EEPROMs Supported
One 8-channel 10-bit Analog-to-Digital Converter, Four Channels Multiplexed with Digital I/Os
SAM-BA™ Boot Assistance
– Default Boot program
– Interface with SAM-BA Graphic User Interface
IEEE® 1149.1 JTAG Boundary Scan on All Digital Pins
5V-tolerant I/Os, Including Four High-current Drive I/O lines, Up to 16 mA Each
Power Supplies
– Embedded 1.8V Regulator, Drawing up to 100 mA for the Core and External Components
– 3.3V VDDIO I/O Lines Power Supply, Independent 3.3V VDDFLASH Flash Power Supply
– 1.8V VDDCORE Core Power Supply with Brownout Detector
Fully Static Operation: Up to 55 MHz at 1.65V and 85°C Worst Case Conditions
Available in 100-lead LQFP Green and 100-ball TFBGA Green Packages
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
1. Description
Atmel's AT91SAM7X512/256/128 is a member of a series of highly integrated Flash microcontrollers based on the 32-bit ARM RISC processor. It features 512/256/128 Kbyte high-speed
Flash and 128/64/32 Kbyte SRAM, a large set of peripherals, including an 802.3 Ethernet MAC
and a CAN controller. A complete set of system functions minimizes the number of external
components.
The embedded Flash memory can be programmed in-system via the JTAG-ICE interface or via
a parallel interface on a production programmer prior to mounting. Built-in lock bits and a security bit protect the firmware from accidental overwrite and preserve its confidentiality.
The AT91SAM7X512/256/128 system controller includes a reset controller capable of managing
the power-on sequence of the microcontroller and the complete system. Correct device operation can be monitored by a built-in brownout detector and a watchdog running off an integrated
RC oscillator.
By combining the ARM7TDMI processor with on-chip Flash and SRAM, and a wide range of
peripheral functions, including USART, SPI, CAN Controller, Ethernet MAC, Timer Counter, RTT
and Analog-to-Digital Converters on a monolithic chip, the AT91SAM7X512/256/128 is a powerful device that provides a flexible, cost-effective solution to many embedded control applications
requiring communication over, for example, Ethernet, CAN wired and Zigbee ™ wireless
networks.
1.1
Configuration Summary of the AT91SAM7X512/256/128
The AT91SAM7X512, AT91SAM7X256 and AT91SAM7X128 differ only in memory sizes. Table
1-1 summarizes the configurations of the three devices.
Table 1-1.
Configuration Summary
Device
Flash
Flash
Organization
SRAM
AT91SAM7X512
512 Kbytes
dual plane
128 Kbytes
AT91SAM7X256
256 Kbytes
single plane
64 Kbytes
AT91SAM7X128
128 Kbytes
single plane
32 Kbytes
3
6120DS–ATARM–03-Oct-06
2. AT91SAM7X512/256/128 Block Diagram
Figure 2-1.
AT91SAM7X512/256/128 Block Diagram
TDI
TDO
TMS
TCK
ICE
JTAG
SCAN
ARM7TDMI
Processor
JTAGSEL
1.8 V
Voltage
Regulator
System Controller
TST
FIQ
VDDCORE
AIC
DRXD
DTXD
VDDIO
Memory Controller
PIO
IRQ0-IRQ1
DBGU
VDDIN
GND
VDDOUT
PDC
SRAM
Embedded
Flash
Controllers
Address
Decoder
Abort
Status
Misalignment
Detection
128/64/32 Kbytes
PDC
PCK0-PCK3
PLLRC
PLL
XIN
XOUT
OSC
VDDFLASH
Flash
ERASE
512/256/128
Kbytes
PMC
RCOSC
Peripheral Bridge
VDDCORE
VDDFLASH
BOD
Peripheral DMA
Controller
ROM
VDDCORE
POR
13 Channels
Fast Flash
Programming
Interface
Reset
Controller
NRST
PGMRDY
PGMNVALID
PGMNOE
PGMCK
PGMM0-PGMM3
PGMD0-PGMD15
PGMNCMD
PGMEN0-PGMEN1
PIT
APB
SAM-BA
WDT
RTT
DMA
FIFO
PIOB
PIO
PIOA
Ethernet MAC 10/100
PDC
USART0
PDC
PDC
USB Device
USART1
PDC
Transceiver
VDDFLASH
FIFO
PWMC
PDC
PIO
PDC
SPI0
SSC
PDC
PDC
PIO
RXD0
TXD0
SCK0
RTS0
CTS0
RXD1
TXD1
SCK1
RTS1
CTS1
DCD1
DSR1
DTR1
RI1
SPI0_NPCS0
SPI0_NPCS1
SPI0_NPCS2
SPI0_NPCS3
SPI0_MISO
SPI0_MOSI
SPI0_SPCK
SPI1_NPCS0
SPI1_NPCS1
SPI1_NPCS2
SPI1_NPCS3
SPI1_MISO
SPI1_MOSI
SPI1_SPCK
ADTRG
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
PDC
Timer Counter
SPI1
TC0
PDC
PDC
TC1
TC2
ADC
ETXCK-ERXCK-EREFCK
ETXEN-ETXER
ECRS-ECOL, ECRSDV
ERXER-ERXDV
ERX0-ERX3
ETX0-ETX3
EMDC
EMDIO
EF100
TWI
CAN
DDM
DDP
PWM0
PWM1
PWM2
PWM3
TF
TK
TD
RD
RK
RF
TCLK0
TCLK1
TCLK2
TIOA0
TIOB0
TIOA1
TIOB1
TIOA2
TIOB2
TWD
TWCK
CANRX
CANTX
ADVREF
4
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
3. Signal Description
Table 3-1.
Signal Description List
Signal Name
Function
Type
Active
Level
Comments
Power
VDDIN
Voltage Regulator and ADC Power
Supply Input
Power
3V to 3.6V
VDDOUT
Voltage Regulator Output
Power
1.85V
VDDFLASH
Flash and USB Power Supply
Power
3V to 3.6V
VDDIO
I/O Lines Power Supply
Power
3V to 3.6V
VDDCORE
Core Power Supply
Power
1.65V to 1.95V
VDDPLL
PLL
Power
1.65V to 1.95V
GND
Ground
Ground
Clocks, Oscillators and PLLs
XIN
Main Oscillator Input
XOUT
Main Oscillator Output
PLLRC
PLL Filter
PCK0 - PCK3
Programmable Clock Output
Input
Output
Input
Output
ICE and JTAG
TCK
Test Clock
Input
No pull-up resistor
TDI
Test Data In
Input
No pull-up resistor.
TDO
Test Data Out
TMS
Test Mode Select
Input
No pull-up resistor.
JTAGSEL
JTAG Selection
Input
Pull-down resistor.
Output
Flash Memory
ERASE
Flash and NVM Configuration Bits Erase
Command
Input
High
Pull-down resistor
I/O
Low
Pull-up resistor, Open Drain
Output
Input
High
Pull-down resistor
Reset/Test
NRST
Microcontroller Reset
TST
Test Mode Select
Debug Unit
DRXD
Debug Receive Data
DTXD
Debug Transmit Data
Input
Output
AIC
IRQ0 - IRQ1
External Interrupt Inputs
Input
FIQ
Fast Interrupt Input
Input
PA0 - PA30
Parallel IO Controller A
I/O
Pulled-up input at reset
PB0 - PB30
Parallel IO Controller B
I/O
Pulled-up input at reset
PIO
5
6120DS–ATARM–03-Oct-06
Table 3-1.
Signal Description List (Continued)
Signal Name
Function
Type
Active
Level
Comments
USB Device Port
DDM
USB Device Port Data -
Analog
DDP
USB Device Port Data +
Analog
USART
SCK0 - SCK1
Serial Clock
I/O
TXD0 - TXD1
Transmit Data
I/O
RXD0 - RXD1
Receive Data
Input
RTS0 - RTS1
Request To Send
CTS0 - CTS1
Clear To Send
Input
DCD1
Data Carrier Detect
Input
DTR1
Data Terminal Ready
DSR1
Data Set Ready
Input
RI1
Ring Indicator
Input
Output
Output
Synchronous Serial Controller
TD
Transmit Data
Output
RD
Receive Data
Input
TK
Transmit Clock
I/O
RK
Receive Clock
I/O
TF
Transmit Frame Sync
I/O
RF
Receive Frame Sync
I/O
Timer/Counter
TCLK0 - TCLK2
External Clock Inputs
Input
TIOA0 - TIOA2
I/O Line A
I/O
TIOB0 - TIOB2
I/O Line B
I/O
PWM Controller
PWM0 - PWM3
PWM Channels
Output
Serial Peripheral Interface - SPIx
SPIx_MISO
Master In Slave Out
I/O
SPIx_MOSI
Master Out Slave In
I/O
SPIx_SPCK
SPI Serial Clock
I/O
SPIx_NPCS0
SPI Peripheral Chip Select 0
I/O
Low
SPIx_NPCS1-NPCS3
SPI Peripheral Chip Select 1 to 3
Output
Low
Two-wire Interface
TWD
Two-wire Serial Data
I/O
TWCK
Two-wire Serial Clock
I/O
6
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
Table 3-1.
Signal Description List (Continued)
Signal Name
Function
Type
Active
Level
Comments
Analog-to-Digital Converter
AD0-AD3
Analog Inputs
Analog
Digital pulled-up inputs at reset
AD4-AD7
Analog Inputs
Analog
Analog Inputs
ADTRG
ADC Trigger
ADVREF
ADC Reference
Input
Analog
Fast Flash Programming Interface
PGMEN0-PGMEN1
Programming Enabling
Input
PGMM0-PGMM3
Programming Mode
Input
PGMD0-PGMD15
Programming Data
I/O
PGMRDY
Programming Ready
Output
High
PGMNVALID
Data Direction
Output
Low
PGMNOE
Programming Read
Input
Low
PGMCK
Programming Clock
Input
PGMNCMD
Programming Command
Input
Low
CAN Controller
CANRX
CAN Input
CANTX
CAN Output
Input
Output
Ethernet MAC 10/100
EREFCK
Reference Clock
Input
RMII only
ETXCK
Transmit Clock
Input
MII only
ERXCK
Receive Clock
Input
MII only
ETXEN
Transmit Enable
Output
ETX0 - ETX3
Transmit Data
Output
ETX0 - ETX1 only in RMII
ETXER
Transmit Coding Error
Output
MII only
ERXDV
Receive Data Valid
Input
MII only
ECRSDV
Carrier Sense and Data Valid
Input
RMII only
ERX0 - ERX3
Receive Data
Input
ERX0 - ERX1 only in RMII
ERXER
Receive Error
Input
ECRS
Carrier Sense
Input
MII only
ECOL
Collision Detected
Input
MII only
EMDC
Management Data Clock
EMDIO
Management Data Input/Output
EF100
Force 100 Mbits/sec.
Output
I/O
Output
High
RMII only
7
6120DS–ATARM–03-Oct-06
4. Package
The AT91SAM7X512/256/128 is available in 100-lead LQFP Green and 100-ball TFBGA RoHScompliant packages.
4.1
100-lead LQFP Package Outline
Figure 4-1 shows the orientation of the 100-lead LQFP package. A detailed mechanical description is given in the Mechanical Characteristics section.
Figure 4-1.
100-lead LQFP Package Outline (Top View)
75
51
76
50
100
26
1
8
25
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
4.2
100-lead LQFP Pinout
Table 4-1.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Pinout in 100-lead LQFP Package
ADVREF
GND
AD4
AD5
AD6
AD7
VDDOUT
VDDIN
PB27/AD0
PB28/AD1
PB29/AD2
PB30/AD3
PA8/PGMM0
PA9/PGMM1
VDDCORE
GND
VDDIO
PA10/PGMM2
PA11/PGMM3
PA12/PGMD0
PA13/PGMD1
PA14/PGMD2
PA15/PGMD3
PA16/PGMD4
PA17/PGMD5
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PA18/PGMD6
PB9
PB8
PB14
PB13
PB6
GND
VDDIO
PB5
PB15
PB17
VDDCORE
PB7
PB12
PB0
PB1
PB2
PB3
PB10
PB11
PA19/PGMD7
PA20/PGMD8
VDDIO
PA21/PGMD9
PA22/PGMD10
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
TDI
GND
PB16
PB4
PA23/PGMD11
PA24/PGMD12
NRST
TST
PA25/PGMD13
PA26/PGMD14
VDDIO
VDDCORE
PB18
PB19
PB20
PB21
PB22
GND
PB23
PB24
PB25
PB26
PA27/PGMD15
PA28
PA29
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
TDO
JTAGSEL
TMS
TCK
PA30
PA0/PGMEN0
PA1/PGMEN1
GND
VDDIO
PA3
PA2
VDDCORE
PA4/PGMNCMD
PA5/PGMRDY
PA6/PGMNOE
PA7/PGMNVALID
ERASE
DDM
DDP
VDDFLASH
GND
XIN/PGMCK
XOUT
PLLRC
VDDPLL
9
6120DS–ATARM–03-Oct-06
4.3
100-ball TFBGA Package Outline
Figure 4-2 shows the orientation of the 100-ball TFBGA package. A detailed mechanical
description is given in the Mechanical Characteristics section of the full datasheet.
Figure 4-2.
100-ball TFBGA Package Outline (Top View)
TOP VIEW
10
9
8
7
6
5
4
3
2
1
A
BALL A1
4.4
B
C
D
E
F
G
H
J
K
100-ball TFBGA Pinout
Pinout in 100-ball TFBGA Package
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
C1
C2
C3
C4
C5
10
Signal Name
PA22/PGMD10
PA21/PGMD9
PA20/PGMD8
PB1
PB7
PB5
PB8
PB9
PA18/PGMD6
VDDIO
TDI
PA19/PGMD7
PB11
PB2
PB12
PB15
PB14
PA14/PGMD2
PA16/PGMD4
PA17/PGMD5
PB16
PB4
PB10
PB3
PB0
Pin
C6
C7
C8
C9
C10
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
E1
E2
E3
E4
E5
E6
E7
E8
E9
E10
Signal Name
PB17
PB13
PA13/PGMD1
PA12/PGMD0
PA15/PGMD3
PA23/PGMD11
PA24/PGMD12
NRST
TST
PB19
PB6
PA10/PGMM2
VDDIO
PB27/AD0
PA11/PGMM3
PA25/PGMD13
PA26/PGMD14
PB18
PB20
TMS
GND
VDDIO
PB28/AD1
VDDIO
GND
Pin
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
H1
H2
H3
H4
H5
Signal Name
PB21
PB23
PB25
PB26
TCK
PA6/PGMNOE
ERASE
VDDCORE
GND
VDDIN
PB22
PB24
PA27/PGMD15
TDO
PA2
PA5/PGMRDY
VDDCORE
GND
PB30/AD3
VDDOUT
VDDCORE
PA28
JTAGSEL
PA3
PA4/PGMNCMD
Pin
H6
H7
H8
H9
H10
J1
J2
J3
J4
J5
J6
J7
J8
J9
J10
K1
K2
K3
K4
K5
K6
K7
K8
K9
K10
Signal Name
PA7/PGMNVALID
PA9/PGMM1
PA8/PGMM0
PB29/AD2
PLLRC
PA29
PA30
PA0/PGMEN0
PA1/PGMEN1
VDDFLASH
GND
XIN/PGMCK
XOUT
GND
VDDPLL
VDDCORE
VDDCORE
DDP
DDM
GND
AD7
AD6
AD5
AD4
ADVREF
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
5. Power Considerations
5.1
Power Supplies
The AT91SAM7X512/256/128 has six types of power supply pins and integrates a voltage regulator, allowing the device to be supplied with only one voltage. The six power supply pin types
are:
• VDDIN pin. It powers the voltage regulator and the ADC; voltage ranges from 3.0V to 3.6V,
3.3V nominal. In order to decrease current consumption, if the voltage regulator and the ADC
are not used, VDDIN, ADVREF, AD4, AD5, AD6 and AD7 should be connected to GND. In
this case, VDDOUT should be left unconnected.
• VDDOUT pin. It is the output of the 1.8V voltage regulator.
• VDDIO pin. It powers the I/O lines; voltage ranges from 3.0V to 3.6V, 3.3V nominal.
• VDDFLASH pin. It powers the USB transceivers and a part of the Flash and is required for
the Flash to operate correctly; voltage ranges from 3.0V to 3.6V, 3.3V nominal.
• VDDCORE pins. They power the logic of the device; voltage ranges from 1.65V to 1.95V,
1.8V typical. It can be connected to the VDDOUT pin with decoupling capacitor. VDDCORE
is required for the device, including its embedded Flash, to operate correctly.
• VDDPLL pin. It powers the oscillator and the PLL. It can be connected directly to the
VDDOUT pin.
No separate ground pins are provided for the different power supplies. Only GND pins are provided and should be connected as shortly as possible to the system ground plane.
5.2
Power Consumption
The AT91SAM7X512/256/128 has a static current of less than 60 µA on VDDCORE at 25°C,
including the RC oscillator, the voltage regulator and the power-on reset when the brownout
detector is deactivated. Activating the brownout detector adds 28 µA static current.
The dynamic power consumption on VDDCORE is less than 90 mA at full speed when running
out of the Flash. Under the same conditions, the power consumption on VDDFLASH does not
exceed 10 mA.
5.3
Voltage Regulator
The AT91SAM7X512/256/128 embeds a voltage regulator that is managed by the System
Controller.
In Normal Mode, the voltage regulator consumes less than 100 µA static current and draws 100
mA of output current.
The voltage regulator also has a Low-power Mode. In this mode, it consumes less than 25 µA
static current and draws 1 mA of output current.
Adequate output supply decoupling is mandatory for VDDOUT to reduce ripple and avoid oscillations. The best way to achieve this is to use two capacitors in parallel: one external 470 pF (or
1 nF) NPO capacitor should be connected between VDDOUT and GND as close to the chip as
possible. One external 2.2 µF (or 3.3 µF) X7R capacitor should be connected between VDDOUT
and GND.
11
6120DS–ATARM–03-Oct-06
Adequate input supply decoupling is mandatory for VDDIN in order to improve startup stability
and reduce source voltage drop. The input decoupling capacitor should be placed close to the
chip. For example, two capacitors can be used in parallel: 100 nF NPO and 4.7 µF X7R.
5.4
Typical Powering Schematics
The AT91SAM7X512/256/128 supports a 3.3V single supply mode. The internal regulator input
connected to the 3.3V source and its output feeds VDDCORE and the VDDPLL. Figure 5-1
shows the power schematics to be used for USB bus-powered systems.
Figure 5-1.
3.3V System Single Power Supply Schematic
VDDFLASH
Power Source
ranges
from 4.5V (USB)
to 18V
DC/DC Converter
VDDIO
VDDIN
Voltage
Regulator
3.3V
VDDOUT
VDDCORE
VDDPLL
12
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
6. I/O Lines Considerations
6.1
JTAG Port Pins
TMS, TDI and TCK are schmitt trigger inputs and are not 5-V tolerant. TMS, TDI and TCK do not
integrate a pull-up resistor.
TDO is an output, driven at up to VDDIO, and has no pull-up resistor.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. The
JTAGSEL pin integrates a permanent pull-down resistor of about 15 kΩ to GND, so that it can be
left unconnected for normal operations.
6.2
Test Pin
The TST pin is used for manufacturing test or fast programming mode of the
AT91SAM7X512/256/128 when asserted high. The TST pin integrates a permanent pull-down
resistor of about 15 kΩ to GND, so that it can be left unconnected for normal operations.
To enter fast programming mode, the TST pin and the PA0 and PA1 pins should be tied high
and PA2 tied to low.
Driving the TST pin at a high level while PA0 or PA1 is driven at 0 leads to unpredictable results.
6.3
Reset Pin
The NRST pin is bidirectional with an open drain output buffer. It is handled by the on-chip reset
controller and can be driven low to provide a reset signal to the external components or asserted
low externally to reset the microcontroller. There is no constraint on the length of the reset pulse,
and the reset controller can guarantee a minimum pulse length. This allows connection of a simple push-button on the NRST pin as system user reset, and the use of the signal NRST to reset
all the components of the system.
The NRST pin integrates a permanent pull-up resistor to VDDIO.
6.4
ERASE Pin
The ERASE pin is used to re-initialize the Flash content and some of its NVM bits. It integrates a
permanent pull-down resistor of about 15 kΩ to GND, so that it can be left unconnected for normal operations.
This pin is debounced by the RC oscillator to improve the glitch tolerance. When the pin is tied to
high during less than 100 ms, ERASE pin is not taken into account. The pin must be tied high
during more than 220 ms to perform the re-initialization of the Flash.
6.5
PIO Controller Lines
All the I/O lines, PA0 to PA30 and PB0 to PB30, are 5V-tolerant and all integrate a programmable pull-up resistor. Programming of this pull-up resistor is performed independently for each I/O
line through the PIO controllers.
5V-tolerant means that the I/O lines can drive voltage level according to VDDIO, but can be
driven with a voltage of up to 5.5V. However, driving an I/O line with a voltage over VDDIO while
the programmable pull-up resistor is enabled will create a current path through the pull-up resis-
13
6120DS–ATARM–03-Oct-06
tor from the I/O line to VDDIO. Care should be taken, in particular at reset, as all the I/O lines
default to input with pull-up resistor enabled at reset.
6.6
I/O Lines Current Drawing
The PIO lines PA0 to PA3 are high-drive current capable. Each of these I/O lines can drive up to
16 mA permanently.
The remaining I/O lines can draw only 8 mA.
However, the total current drawn by all the I/O lines cannot exceed 200 mA.
14
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
7. Processor and Architecture
7.1
ARM7TDMI Processor
• RISC processor based on ARMv4T Von Neumann architecture
– Runs at up to 55 MHz, providing 0.9 MIPS/MHz
• Two instruction sets
– ARM high-performance 32-bit instruction set
– Thumb high code density 16-bit instruction set
• Three-stage pipeline architecture
– Instruction Fetch (F)
– Instruction Decode (D)
– Execute (E)
7.2
Debug and Test Features
• Integrated embedded in-circuit emulator
– Two watchpoint units
– Test access port accessible through a JTAG protocol
– Debug communication channel
• Debug Unit
– Two-pin UART
– Debug communication channel interrupt handling
– Chip ID Register
• IEEE1149.1 JTAG Boundary-scan on all digital pins
7.3
Memory Controller
• Programmable Bus Arbiter
– Handles requests from the ARM7TDMI, the Ethernet MAC and the Peripheral DMA
Controller
• Address decoder provides selection signals for
– Three internal 1 Mbyte memory areas
– One 256 Mbyte embedded peripheral area
• Abort Status Registers
– Source, Type and all parameters of the access leading to an abort are saved
– Facilitates debug by detection of bad pointers
• Misalignment Detector
– Alignment checking of all data accesses
– Abort generation in case of misalignment
• Remap Command
– Remaps the SRAM in place of the embedded non-volatile memory
– Allows handling of dynamic exception vectors
15
6120DS–ATARM–03-Oct-06
• Embedded Flash Controller
– Embedded Flash interface, up to three programmable wait states
– Prefetch buffer, buffering and anticipating the 16-bit requests, reducing the required
wait states
– Key-protected program, erase and lock/unlock sequencer
– Single command for erasing, programming and locking operations
– Interrupt generation in case of forbidden operation
7.4
Peripheral DMA Controller
• Handles data transfer between peripherals and memories
• Thirteen channels
– Two for each USART
– Two for the Debug Unit
– Two for the Serial Synchronous Controller
– Two for each Serial Peripheral Interface
– One for the Analog-to-digital Converter
• Low bus arbitration overhead
– One Master Clock cycle needed for a transfer from memory to peripheral
– Two Master Clock cycles needed for a transfer from peripheral to memory
• Next Pointer management for reducing interrupt latency requirements
16
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
8. Memories
8.1
AT91SAM7X512
• 512 Kbytes of dual-plane Flash Memory
– 2 contiguous banks of 1024 pages of 256 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 32 lock bits, protecting 32 sectors of 64 pages
– Protection Mode to secure contents of the Flash
• 128 Kbytes of Fast SRAM
– Single-cycle access at full speed
8.2
AT91SAM7X256
• 256 Kbytes of Flash Memory
– 1024 pages of 256 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 16 lock bits, each protecting 16 sectors of 64 pages
– Protection Mode to secure contents of the Flash
• 64 Kbytes of Fast SRAM
– Single-cycle access at full speed
8.3
AT91SAM7X128
• 128 Kbytes of Flash Memory
– 512 pages of 256 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 8 lock bits, each protecting 8 sectors of 64 pages
– Protection Mode to secure contents of the Flash
• 32 Kbytes of Fast SRAM
– Single-cycle access at full speed
17
6120DS–ATARM–03-Oct-06
Figure 8-1.
AT91SAM7X512/256/128 Memory Mapping
Internal Memory Mapping
0x0000 0000
Note:
(1) Can be ROM, Flash or SRAM
depending on GPNVM2 and REMAP
Boot Memory (1)
Flash before Remap
SRAM after Remap
1 MBytes
Internal Flash
1 MBytes
Internal SRAM
1 MBytes
Internal ROM
1 MBytes
0x000F FFF
0x0010 0000
0x001F FFF
0x0020 0000
0x002F FFF
0x0030 0000
Address Memory Space
0x0000 0000
0x003F FFF
0x0040 0000
Internal Memories
256 MBytes
Reserved
252 MBytes
0x0FFF FFFF
0x0FFF FFFF
System Controller Mapping
0x1000 0000
0xFFFF F000
AIC
512 Bytes/128 registers
DBGU
512 Bytes/128 registers
PIOA
512 Bytes/128 registers
PIOB
512 Bytes/128 registers
0xFFFF F1FF
0xFFFF F200
Peripheral Mapping
0xF000 0000
Reserved
Undefined
(Abort)
14 x 256 MBytes
3,584 MBytes
0xFFF9 FFFF
0xFFFA 0000
0xFFFA 3FFF
0xFFFA 4000
0xFFFA FFFF
0xFFFB 0000
TC0, TC1, TC2
16 Kbytes
0xFFFF F3FF
0xFFFF F400
Reserved
UDP
16 Kbytes
0xFFFB 3FFF
0xFFFB 4000
0xFFFF F5FF
0xFFFF F600
Reserved
0xFFFB 7FFF
0xFFFB 8000
0xFFFB BFFF
0xFFFB C000
0xEFFF FFFF
0xFFFB FFFF
0xFFFC 0000
0xF000 0000
0xFFFC 3FFF
0xFFFC 4000
Internal Peripherals
0xFFFF FFFF
256 MBytes
TWI
16 Kbytes
Reserved
Reserved
USART0
16 Kbytes
USART1
16 Kbytes
0xFFFC 7FFF
0xFFFC 8000
Reserved
0xFFFC BFFF
0xFFFC C000
PWMC
16 Kbytes
CAN
16 Kbytes
SSC
16 Kbytes
ADC
16 Kbytes
EMAC
16 Kbytes
SPI0
16 Kbytes
SPI1
16 Kbytes
0xFFFC FFFF
0xFFFD 0000
0xFFFD 3FFF
0xFFFD 4000
0xFFFD 7FFF
0xFFFD 8000
0xFFFD BFFF
0xFFFD C000
0xFFFD FFFF
0xFFFE 0000
0xFFFE 3FFF
0xFFFE 4000
0xFFFE 7FFF
0xFFFE 8000
0xFFFF F7FF
0xFFFF F800
0xFFFF FBFF
0xFFFF FC00
0xFFFF FCFF
0xFFFF FD00
0xFFFF FD0F
0xFFFF FD4F
Reserved
0xFFFF FFFF
18
256 Bytes/64 registers
RSTC
16 Bytes/4 registers
Reserved
0xFFFF FD20
0xFFFF FC2F
0xFFFF FD30
0xFFFF FC3F
0xFFFF FD40
RTT
16 Bytes/4 registers
PIT
16 Bytes/4 registers
WDT
16 Bytes/4 registers
Reserved
0xFFFF FD60
0xFFFF FC6F
0xFFFF FD70
0xFFFF FEFF
0xFFFF FF00
VREG
4 Bytes/1 register
Reserved
MC
0xFFFF EFFF
0xFFFF F000
PMC
256 Bytes/64 registers
SYSC
0xFFFF FFFF
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
8.4
8.4.1
Memory Mapping
Internal SRAM
• The AT91SAM7X512 embeds a high-speed 128 Kbyte SRAM bank.
• The AT91SAM7X256 embeds a high-speed 64 Kbyte SRAM bank.
• The AT91SAM7X128 embeds a high-speed 32 Kbyte SRAM bank.
After reset and until the Remap Command is performed, the SRAM is only accessible at address
0x0020 0000. After Remap, the SRAM also becomes available at address 0x0.
8.4.2
Internal ROM
The AT91SAM7X512/256/128 embeds an Internal ROM. At any time, the ROM is mapped at
address 0x30 0000. The ROM contains the FFPI and the SAM-BA program.
8.4.3
Internal Flash
• The AT91SAM7X512 features two banks (dual plane) of 256 Kbytes of Flash.
• The AT91SAM7X256 features one bank (single plane) of 256 Kbytes of Flash.
• The AT91SAM7X128 features one bank (single plane) of 128 Kbytes of Flash.
At any time, the Flash is mapped to address 0x0010 0000. It is also accessible at address 0x0
after the reset, if GPNVM bit 2 is cleared and before the Remap Command.
A general purpose NVM (GPNVM) bit is used to boot either on the ROM (default) or from the
Flash.
This GPNVM bit can be cleared or set respectively through the commands “Clear General-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
Setting the GPNVM Bit 2 selects the boot from the Flash. Asserting ERASE clears the GPNVM
Bit 2 and thus selects the boot from the ROM by default.
Figure 8-2.
Internal Memory Mapping with GPNVM Bit 2 = 0 (default)
0x0000 0000
0x000F FFFF
ROM Before Remap
SRAM After Remap
1 M Bytes
0x0010 0000
Internal FLASH
1 M Bytes
Internal SRAM
1 M Bytes
Internal ROM
1 M Bytes
0x001F FFFF
0x0020 0000
256M Bytes
0x002F FFFF
0x0030 0000
0x003F FFFF
0x0040 0000
Undefined Areas
(Abort)
252 M Bytes
0x0FFF FFFF
19
6120DS–ATARM–03-Oct-06
Figure 8-3.
Internal Memory Mapping with GPNVM Bit 2 = 1
0x0000 0000
0x000F FFFF
Flash Before Remap
SRAM After Remap
1 M Bytes
0x0010 0000
Internal FLASH
1 M Bytes
Internal SRAM
1 M Bytes
Internal ROM
1 M Bytes
0x001F FFFF
0x0020 0000
256M Bytes
0x002F FFFF
0x0030 0000
0x003F FFFF
0x0040 0000
Undefined Areas
(Abort)
252 M Bytes
0x0FFF FFFF
8.5
Embedded Flash
8.5.1
Flash Overview
• The Flash of the AT91SAM7X512 is organized in two banks (dual plane) of 1024 pages of
256 bytes. The 524,288 bytes are organized in 32-bit words.
• The Flash of the AT91SAM7X256 is organized in 1024 pages of 256 bytes (single plane). It
reads as 65,536 32-bit words.
• The Flash of the AT91SAM7X128 is organized in 512 pages of 256 bytes (single plane). It
reads as 32,768 32-bit words.
The Flash contains a 256-byte write buffer, accessible through a 32-bit interface.
The Flash benefits from the integration of a power reset cell and from the brownout detector.
This prevents code corruption during power supply changes, even in the worst conditions.
When Flash is not used (read or write access), it is automatically placed into standby mode.
8.5.2
Embedded Flash Controller
The Embedded Flash Controller (EFC) manages accesses performed by the masters of the system. It enables reading the Flash and writing the write buffer. It also contains a User Interface,
mapped within the Memory Controller on the APB. The User Interface allows:
• programming of the access parameters of the Flash (number of wait states, timings, etc.)
• starting commands such as full erase, page erase, page program, NVM bit set, NVM bit
clear, etc.
• getting the end status of the last command
• getting error status
• programming interrupts on the end of the last commands or on errors
The Embedded Flash Controller also provides a dual 32-bit Prefetch Buffer that optimizes 16-bit
access to the Flash. This is particularly efficient when the processor is running in Thumb mode.
Two EFCs are embedded in the AT91SAM7X512 to control each bank of 256 KBytes. Dualplane organization allows concurrent read and program functionality. Read from one memory
20
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
plane may be performed even while program or erase functions are being executed in the other
memory plane.
One EFC is embedded in the AT91SAM7X256/128 to control the single plane of 256/128
KBytes.
8.5.3
8.5.3.1
Lock Regions
AT91SAM7X512
Two Embedded Flash Controllers each manage 16 lock bits to protect 16 regions of the flash
against inadvertent flash erasing or programming commands. The AT91SAM7X512 contains 32
lock regions and each lock region contains 64 pages of 256 bytes. Each lock region has a size of
16 Kbytes.
If a locked-region’s erase or program command occurs, the command is aborted and the EFC
trigs an interrupt.
The 32 NVM bits are software programmable through both of the EFC User Interfaces. The command “Set Lock Bit” enables the protection. The command “Clear Lock Bit” unlocks the lock
region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
8.5.3.2
AT91SAM7X256
The Embedded Flash Controller manages 16 lock bits to protect 16 regions of the flash against
inadvertent flash erasing or programming commands. The AT91SAM7X256 contains 16 lock
regions and each lock region contains 64 pages of 256 bytes. Each lock region has a size of 16
Kbytes.
If a locked-region’s erase or program command occurs, the command is aborted and the EFC
trigs an interrupt.
The 16 NVM bits are software programmable through the EFC User Interface. The command
“Set Lock Bit” enables the protection. The command “Clear Lock Bit” unlocks the lock region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
8.5.3.3
AT91SAM7X128
The Embedded Flash Controller manages 8 lock bits to protect 8 regions of the flash against
inadvertent flash erasing or programming commands. The AT91SAM7X128 contains 8 lock
regions and each lock region contains 64 pages of 256 bytes. Each lock region has a size of 16
Kbytes.
If a locked-region’s erase or program command occurs, the command is aborted and the EFC
trigs an interrupt.
The 8 NVM bits are software programmable through the EFC User Interface. The command “Set
Lock Bit” enables the protection. The command “Clear Lock Bit” unlocks the lock region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
8.5.4
Security Bit Feature
The AT91SAM7X512/256/128 features a security bit, based on a specific NVM-Bit. When the
security is enabled, any access to the Flash, either through the ICE interface or through the Fast
21
6120DS–ATARM–03-Oct-06
Flash Programming Interface, is forbidden. This ensures the confidentiality of the code programmed in the Flash.
This security bit can only be enabled, through the Command “Set Security Bit” of the EFC User
Interface. Disabling the security bit can only be achieved by asserting the ERASE pin at 1, and
after a full flash erase is performed. When the security bit is deactivated, all accesses to the
flash are permitted.
It is important to note that the assertion of the ERASE pin should always be longer than 220 ms.
As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal
operation. However, it is safer to connect it directly to GND for the final application.
8.5.5
Non-volatile Brownout Detector Control
Two general purpose NVM (GPNVM) bits are used for controlling the brownout detector (BOD),
so that even after a power loss, the brownout detector operations remain in their state.
These two GPNVM bits can be cleared or set respectively through the commands “Clear General-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
• GPNVM Bit 0 is used as a brownout detector enable bit. Setting the GPNVM Bit 0 enables
the BOD, clearing it disables the BOD. Asserting ERASE clears the GPNVM Bit 0 and thus
disables the brownout detector by default.
• The GPNVM Bit 1 is used as a brownout reset enable signal for the reset controller. Setting
the GPNVM Bit 1 enables the brownout reset when a brownout is detected, Clearing the
GPNVM Bit 1 disables the brownout reset. Asserting ERASE disables the brownout reset by
default.
8.5.6
Calibration Bits
Eight NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits
are factory configured and cannot be changed by the user. The ERASE pin has no effect on the
calibration bits.
8.6
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial
JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang-programming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect
commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered
when the TST pin and the PA0 and PA1 pins are all tied high.
8.7
SAM-BA Boot Assistant
The SAM-BA Boot Assistant is a default Boot Program that provides an easy way to program insitu the on-chip Flash memory.
The SAM-BA Boot Assistant supports serial communication via the DBGU or the USB Device
Port.
• Communication via the DBGU supports a wide range of crystals from 3 to 20 MHz via
software auto-detection.
22
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
• Communication via the USB Device Port is limited to an 18.432 MHz crystal.
The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI).
The SAM-BA Boot is in ROM and is mapped at address 0x0 when the GPNVM Bit 2 is set to 0.
When GPNVM bit 2 is set to 1, the device boots from the Flash.
When GPNVM bit 2 is set to 0, the device boots from ROM (SAM-BA).
23
6120DS–ATARM–03-Oct-06
9. System Controller
The System Controller manages all vital blocks of the microcontroller: interrupts, clocks, power,
time, debug and reset.
The System Controller peripherals are all mapped to the highest 4 Kbytes of address space,
between addresses 0xFFFF F000 and 0xFFFF FFFF.
Figure 9-1 on page 25 shows the System Controller Block Diagram.
Figure 8-1 on page 18 shows the mapping of the User Interface of the System Controller peripherals. Note that the Memory Controller configuration user interface is also mapped within this
address space.
24
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
Figure 9-1.
System Controller Block Diagram
System Controller
jtag_nreset
Boundary Scan
TAP Controller
nirq
irq0-irq1
Advanced
Interrupt
Controller
fiq
periph_irq[2..19]
nfiq
proc_nreset
ARM7TDMI
PCK
int
debug
pit_irq
rtt_irq
wdt_irq
dbgu_irq
pmc_irq
rstc_irq
efc_irq
power_on_reset
force_ntrst
MCK
periph_nreset
dbgu_irq
Debug
Unit
force_ntrst
dbgu_txd
dbgu_rxd
security_bit
MCK
debug
periph_nreset
SLCK
periph_nreset
Periodic
Interval
Timer
pit_irq
Real-Time
Timer
rtt_irq
Watchdog
Timer
wdt_irq
flash_poe
cal
gpnvm[0]
flash_wrdis
BOD
power_on_reset
jtag_nreset
POR
flash_poe
efc_irq
bod_rst_en
MCK
NRST
periph_nreset
proc_nreset
SLCK
XOUT
Voltage
Regulator
Mode
Controller
standby
Voltage
Regulator
cal
SLCK
MAINCK
Memory
Controller
proc_nreset
Reset
Controller
rstc_irq
OSC
gpnvm[0..2]
wdt_fault
WDRPROC
gpnvm[1]
en
XIN
Embedded
Flash
cal
SLCK
debug
idle
proc_nreset
RCOSC
flash_wrdis
periph_clk[2..18]
Power
Management
Controller
UDPCK
pck[0-3]
periph_clk[11]
PCK
periph_nreset
UDPCK
USB Device
Port
periph_irq[11]
MCK
usb_suspend
PLLRC
PLL
PLLCK
pmc_irq
int
idle
periph_nreset
periph_clk[4..19]
usb_suspend
periph_nreset
irq0-irq1
periph_clk[2-3]
dbgu_rxd
Embedded
Peripherals
periph_irq{2-3]
periph_nreset
PIO
Controller
fiq
periph_irq[4..19]
dbgu_txd
in
PA0-PA30
PB0-PB30
out
enable
25
6120DS–ATARM–03-Oct-06
9.1
Reset Controller
• Based on one power-on reset cell and one brownout detector
• Status of the last reset, either Power-up Reset, Software Reset, User Reset, Watchdog
Reset, Brownout Reset
• Controls the internal resets and the NRST pin output
• Allows to shape a signal on the NRST line, guaranteeing that the length of the pulse meets
any requirement.
9.1.1
Brownout Detector and Power-on Reset
The AT91SAM7X512/256/128 embeds one brownout detection circuit and a power-on reset cell.
The power-on reset is supplied with and monitors VDDCORE.
Both signals are provided to the Flash to prevent any code corruption during power-up or powerdown sequences or if brownouts occur on the power supplies.
The power-on reset cell has a limited-accuracy threshold at around 1.5V. Its output remains low
during power-up until VDDCORE goes over this voltage level. This signal goes to the reset controller and allows a full re-initialization of the device.
The brownout detector monitors the VDDCORE and VDDFLASH levels during operation by
comparing them to a fixed trigger level. It secures system operations in the most difficult environments and prevents code corruption in case of brownout on the VDDCORE or VDDFLASH.
When the brownout detector is enabled and VDDCORE decreases to a value below the trigger
level (Vbot18-, defined as Vbot18 - hyst/2), the brownout output is immediately activated.
When VDDCORE increases above the trigger level (Vbot18+, defined as Vbot18 + hyst/2), the
reset is released. The brownout detector only detects a drop if the voltage on VDDCORE stays
below the threshold voltage for longer than about 1µs.
The VDDCORE threshold voltage has a hysteresis of about 50 mV, to ensure spike free brownout detection. The typical value of the brownout detector threshold is 1.68V with an accuracy of
± 2% and is factory calibrated.
When the brownout detector is enabled and VDDFLASH decreases to a value below the trigger
level (Vbot33-, defined as Vbot33 - hyst/2), the brownout output is immediately activated.
When VDDFLASH increases above the trigger level (Vbot33+, defined as Vbot33 + hyst/2), the
reset is released. The brownout detector only detects a drop if the voltage on VDDCORE stays
below the threshold voltage for longer than about 1µs.
The VDDFLASH threshold voltage has a hysteresis of about 50 mV, to ensure spike free brownout detection. The typical value of the brownout detector threshold is 2.80V with an accuracy of
± 3.5% and is factory calibrated.
The brownout detector is low-power, as it consumes less than 28 µA static current. However, it
can be deactivated to save its static current. In this case, it consumes less than 1µA. The deactivation is configured through the GPNVM bit 0 of the Flash.
26
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
9.2
Clock Generator
The Clock Generator embeds one low-power RC Oscillator, one Main Oscillator and one PLL
with the following characteristics:
• RC Oscillator ranges between 22 KHz and 42 KHz
• Main Oscillator frequency ranges between 3 and 20 MHz
• Main Oscillator can be bypassed
• PLL output ranges between 80 and 200 MHz
It provides SLCK, MAINCK and PLLCK.
Figure 9-2.
Clock Generator Block Diagram
Clock Generator
XIN
Embedded
RC
Oscillator
Slow Clock
SLCK
Main
Oscillator
Main Clock
MAINCK
PLL and
Divider
PLL Clock
PLLCK
XOUT
PLLRC
Status
Control
Power
Management
Controller
27
6120DS–ATARM–03-Oct-06
9.3
Power Management Controller
The Power Management Controller uses the Clock Generator outputs to provide:
• the Processor Clock PCK
• the Master Clock MCK
• the USB Clock UDPCK
• all the peripheral clocks, independently controllable
• four programmable clock outputs
The Master Clock (MCK) is programmable from a few hundred Hz to the maximum operating frequency of the device.
The Processor Clock (PCK) switches off when entering processor idle mode, thus allowing
reduced power consumption while waiting for an interrupt.
Figure 9-3.
Power Management Controller Block Diagram
Processor
Clock
Controller
Master Clock Controller
SLCK
MAINCK
PLLCK
PCK
int
Idle Mode
Prescaler
/1,/2,/4,...,/64
MCK
Peripherals
Clock Controller
periph_clk[2..18]
ON/OFF
Programmable Clock Controller
SLCK
MAINCK
PLLCK
Prescaler
/1,/2,/4,...,/64
pck[0..3]
USB Clock Controller
ON/OFF
PLLCK
9.4
Divider
/1,/2,/4
UDPCK
Advanced Interrupt Controller
• Controls the interrupt lines (nIRQ and nFIQ) of an ARM Processor
• Individually maskable and vectored interrupt sources
– Source 0 is reserved for the Fast Interrupt Input (FIQ)
– Source 1 is reserved for system peripherals (RTT, PIT, EFC, PMC, DBGU, etc.)
– Other sources control the peripheral interrupts or external interrupts
– Programmable edge-triggered or level-sensitive internal sources
– Programmable positive/negative edge-triggered or high/low level-sensitive external
sources
• 8-level Priority Controller
– Drives the normal interrupt nIRQ of the processor
– Handles priority of the interrupt sources
28
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
– Higher priority interrupts can be served during service of lower priority interrupt
• Vectoring
– Optimizes interrupt service routine branch and execution
– One 32-bit vector register per interrupt source
– Interrupt vector register reads the corresponding current interrupt vector
• Protect Mode
– Easy debugging by preventing automatic operations
• Fast Forcing
– Permits redirecting any interrupt source on the fast interrupt
• General Interrupt Mask
– Provides processor synchronization on events without triggering an interrupt
9.5
Debug Unit
• Comprises:
– One two-pin UART
– One Interface for the Debug Communication Channel (DCC) support
– One set of Chip ID Registers
– One Interface providing ICE Access Prevention
• Two-pin UART
– USART-compatible User Interface
– Programmable Baud Rate Generator
– Parity, Framing and Overrun Error
– Automatic Echo, Local Loopback and Remote Loopback Channel Modes
• Debug Communication Channel Support
– Offers visibility of COMMRX and COMMTX signals from the ARM Processor
• Chip ID Registers
– Identification of the device revision, sizes of the embedded memories, set of
peripherals
– Chip ID is 0x275C 0A40 (VERSION 0) for AT91SAM7X512
– Chip ID is 0x275B 0940 (VERSION 0) for AT91SAM7X256
– Chip ID is 0x275A 0740 (VERSION 0) for AT91SAM7X128
9.6
Periodic Interval Timer
• 20-bit programmable counter plus 12-bit interval counter
9.7
Watchdog Timer
• 12-bit key-protected Programmable Counter running on prescaled SLCK
• Provides reset or interrupt signals to the system
• Counter may be stopped while the processor is in debug state or in idle mode
29
6120DS–ATARM–03-Oct-06
9.8
Real-time Timer
• 32-bit free-running counter with alarm running on prescaled SLCK
• Programmable 16-bit prescaler for SLCK accuracy compensation
9.9
PIO Controllers
• Two PIO Controllers, each controlling 31 I/O lines
• Fully programmable through set/clear registers
• Multiplexing of two peripheral functions per I/O line
• For each I/O line (whether assigned to a peripheral or used as general-purpose I/O)
– Input change interrupt
– Half a clock period glitch filter
– Multi-drive option enables driving in open drain
– Programmable pull-up on each I/O line
– Pin data status register, supplies visibility of the level on the pin at any time
• Synchronous output, provides Set and Clear of several I/O lines in a single write
9.10
Voltage Regulator Controller
The purpose of this controller is to select the Power Mode of the Voltage Regulator between
Normal Mode (bit 0 is cleared) or Standby Mode (bit 0 is set).
30
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
10. Peripherals
10.1
User Interface
The User Peripherals are mapped in the 256 Mbytes of address space between 0xF000 0000
and 0xFFFF EFFF. Each peripheral is allocated 16 Kbytes of address space.
A complete memory map is provided in Figure 8-1 on page 18.
10.2
Peripheral Identifiers
The AT91SAM7X512/256/128 embeds a wide range of peripherals. Table 10-1 defines the
Peripheral Identifiers of the AT91SAM7X512/256/128. Unique peripheral identifiers are defined
for both the Advanced Interrupt Controller and the Power Management Controller.
Table 10-1.
Peripheral Identifiers
Peripheral ID
Peripheral Mnemonic
Peripheral Name
External
Interrupt
0
AIC
Advanced Interrupt Controller
FIQ
(1)
1
SYSC
System Controller
2
PIOA
Parallel I/O Controller A
3
PIOB
Parallel I/O Controller B
4
SPI0
Serial Peripheral Interface 0
5
SPI1
Serial Peripheral Interface 1
6
US0
USART 0
7
US1
USART 1
8
SSC
Synchronous Serial Controller
9
TWI
Two-wire Interface
10
PWMC
Pulse Width Modulation Controller
11
UDP
USB Device Port
12
TC0
Timer/Counter 0
13
TC1
Timer/Counter 1
14
TC2
Timer/Counter 2
15
CAN
CAN Controller
16
EMAC
17
ADC
(1)
18 - 29
Reserved
30
AIC
Advanced Interrupt Controller
IRQ0
31
AIC
Advanced Interrupt Controller
IRQ1
Note:
Ethernet MAC
Analog-to Digital Converter
1. Setting SYSC and ADC bits in the clock set/clear registers of the PMC has no effect. The System Controller and ADC are continuously clocked.
31
6120DS–ATARM–03-Oct-06
10.3
Peripheral Multiplexing on PIO Lines
The AT91SAM7X512/256/128 features two PIO controllers, PIOA and PIOB, that multiplex the
I/O lines of the peripheral set.
Each PIO Controller controls 31 lines. Each line can be assigned to one of two peripheral functions, A or B. Some of them can also be multiplexed with the analog inputs of the ADC
Controller.
Table 10-2 on page 33 and Table 10-3 on page 34 defines how the I/O lines of the peripherals A,
B or the analog inputs are multiplexed on the PIO Controller A and PIO Controller B. The two
columns “Function” and “Comments” have been inserted for the user’s own comments; they may
be used to track how pins are defined in an application.
Note that some peripheral functions that are output only, may be duplicated in the table.
At reset, all I/O lines are automatically configured as input with the programmable pull-up
enabled, so that the device is maintained in a static state as soon as a reset is detected.
32
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
10.4
PIO Controller A Multiplexing
Table 10-2.
Multiplexing on PIO Controller A
PIO Controller A
Peripheral B
Application Usage
I/O Line
Peripheral A
Comments
PA0
RXD0
High-Drive
PA1
TXD0
High-Drive
PA2
SCK0
SPI1_NPCS1
High-Drive
PA3
RTS0
SPI1_NPCS2
High-Drive
PA4
CTS0
SPI1_NPCS3
PA5
RXD1
PA6
TXD1
PA7
SCK1
SPI0_NPCS1
PA8
RTS1
SPI0_NPCS2
PA9
CTS1
SPI0_NPCS3
PA10
TWD
PA11
TWCK
PA12
SPI_NPCS0
PA13
SPI0_NPCS1
PCK1
PA14
SPI0_NPCS2
IRQ1
PA15
SPI0_NPCS3
TCLK2
PA16
SPI0_MISO
PA17
SPI0_MOSI
PA18
SPI0_SPCK
PA19
CANRX
PA20
CANTX
PA21
TF
SPI1_NPCS0
PA22
TK
SPI1_SPCK
PA23
TD
SPI1_MOSI
PA24
RD
SPI1_MISO
PA25
RK
SPI1_NPCS1
PA26
RF
SPI1_NPCS2
PA27
DRXD
PCK3
PA28
DTXD
PA29
FIQ
SPI1_NPCS3
PA30
IRQ0
PCK2
Function
Comments
33
6120DS–ATARM–03-Oct-06
10.5
PIO Controller B Multiplexing
Table 10-3.
Multiplexing on PIO Controller B
PIO Controller B
34
Application Usage
I/O Line
Peripheral A
Peripheral B
Comments
PB0
ETXCK/EREFCK
PCK0
PB1
ETXEN
PB2
ETX0
PB3
ETX1
PB4
ECRS
PB5
ERX0
PB6
ERX1
PB7
ERXER
PB8
EMDC
PB9
EMDIO
PB10
ETX2
SPI1_NPCS1
PB11
ETX3
SPI1_NPCS2
PB12
ETXER
TCLK0
PB13
ERX2
SPI0_NPCS1
PB14
ERX3
SPI0_NPCS2
PB15
ERXDV/ECRSDV
PB16
ECOL
SPI1_NPCS3
PB17
ERXCK
SPI0_NPCS3
PB18
EF100
ADTRG
PB19
PWM0
TCLK1
PB20
PWM1
PCK0
PB21
PWM2
PCK1
PB22
PWM3
PCK2
PB23
TIOA0
DCD1
PB24
TIOB0
DSR1
PB25
TIOA1
DTR1
PB26
TIOB1
RI1
PB27
TIOA2
PWM0
AD0
PB28
TIOB2
PWM1
AD1
PB29
PCK1
PWM2
AD2
PB30
PCK2
PWM3
AD3
Function
Comments
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
10.6
Ethernet MAC
• DMA Master on Receive and Transmit Channels
• Compatible with IEEE Standard 802.3
• 10 and 100 Mbit/s operation
• Full- and half-duplex operation
• Statistics Counter Registers
• MII/RMII interface to the physical layer
• Interrupt generation to signal receive and transmit completion
• 28-byte transmit FIFO and 28-byte receive FIFO
• Automatic pad and CRC generation on transmitted frames
• Automatic discard of frames received with errors
• Address checking logic supports up to four specific 48-bit addresses
• Support Promiscuous Mode where all valid received frames are copied to memory
• Hash matching of unicast and multicast destination addresses
• Physical layer management through MDIO interface
• Half-duplex flow control by forcing collisions on incoming frames
• Full-duplex flow control with recognition of incoming pause frames
• Support for 802.1Q VLAN tagging with recognition of incoming VLAN and priority tagged
frames
• Multiple buffers per receive and transmit frame
• Jumbo frames up to 10240 bytes supported
10.7
Serial Peripheral Interface
• Supports communication with external serial devices
– Four chip selects with external decoder allow communication with up to 15
peripherals
– Serial memories, such as DataFlash® and 3-wire EEPROMs
– Serial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and
Sensors
– External co-processors
• Master or slave serial peripheral bus interface
– 8- to 16-bit programmable data length per chip select
– Programmable phase and polarity per chip select
– Programmable transfer delays per chip select, between consecutive transfers and
between clock and data
– Programmable delay between consecutive transfers
– Selectable mode fault detection
– Maximum frequency at up to Master Clock
10.8
Two-wire Interface
• Master Mode only
• Compatibility with standard two-wire serial memories
35
6120DS–ATARM–03-Oct-06
• One, two or three bytes for slave address
• Sequential read/write operations
10.9
USART
• Programmable Baud Rate Generator
• 5- to 9-bit full-duplex synchronous or asynchronous serial communications
– 1, 1.5 or 2 stop bits in Asynchronous Mode
– 1 or 2 stop bits in Synchronous Mode
– Parity generation and error detection
– Framing error detection, overrun error detection
– MSB or LSB first
– Optional break generation and detection
– By 8 or by 16 over-sampling receiver frequency
– Hardware handshaking RTS - CTS
– Modem Signals Management DTR-DSR-DCD-RI on USART1
– Receiver time-out and transmitter timeguard
– Multi-drop Mode with address generation and detection
• RS485 with driver control signal
• ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards
– NACK handling, error counter with repetition and iteration limit
• IrDA modulation and demodulation
– Communication at up to 115.2 Kbps
• Test Modes
– Remote Loopback, Local Loopback, Automatic Echo
10.10 Serial Synchronous Controller
• Provides serial synchronous communication links used in audio and telecom applications
• Contains an independent receiver and transmitter and a common clock divider
• Offers a configurable frame sync and data length
• Receiver and transmitter can be programmed to start automatically or on detection of
different event on the frame sync signal
• Receiver and transmitter include a data signal, a clock signal and a frame synchronization
signal
10.11 Timer Counter
• Three 16-bit Timer Counter Channels
– Three output compare or two input capture
• Wide range of functions including:
– Frequency measurement
– Event counting
– Interval measurement
– Pulse generation
36
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
– Delay timing
– Pulse Width Modulation
– Up/down capabilities
• Each channel is user-configurable and contains:
– Three external clock inputs
• Five internal clock inputs, as defined in Table 10-4
Table 10-4.
Timer Counter Clocks Assignment
TC Clock input
Clock
TIMER_CLOCK1
MCK/2
TIMER_CLOCK2
MCK/8
TIMER_CLOCK3
MCK/32
TIMER_CLOCK4
MCK/128
TIMER_CLOCK5
MCK/1024
– Two multi-purpose input/output signals
– Two global registers that act on all three TC channels
10.12 Pulse Width Modulation Controller
• Four channels, one 16-bit counter per channel
• Common clock generator, providing thirteen different clocks
– One Modulo n counter providing eleven clocks
– Two independent linear dividers working on modulo n counter outputs
• Independent channel programming
– Independent enable/disable commands
– Independent clock selection
– Independent period and duty cycle, with double buffering
– Programmable selection of the output waveform polarity
– Programmable center or left aligned output waveform
10.13 USB Device Port
• USB V2.0 full-speed compliant,12 Mbits per second
• Embedded USB V2.0 full-speed transceiver
• Embedded 1352-byte dual-port RAM for endpoints
• Six endpoints
– Endpoint 0: 8 bytes
– Endpoint 1 and 2: 64 bytes ping-pong
– Endpoint 3: 64 bytes
– Endpoint 4 and 5: 256 bytes ping-pong
– Ping-pong Mode (two memory banks) for bulk endpoints
• Suspend/resume logic
37
6120DS–ATARM–03-Oct-06
10.14 CAN Controller
•
Fully compliant with CAN 2.0A and 2.0B
•
Bit rates up to 1Mbit/s
•
Eight object oriented mailboxes each with the following properties:
– CAN Specification 2.0 Part A or 2.0 Part B Programmable for each Message
– Object configurable to receive (with overwrite or not) or transmit
– Local tag and mask filters up to 29-bit identifier/channel
– 32-bit access to data registers for each mailbox data object
– Uses a 16-bit time stamp on receive and transmit message
– Hardware concatenation of ID unmasked bitfields to speedup family ID processing
– 16-bit internal timer for time stamping and network synchronization
– Programmable reception buffer length up to 8 mailbox objects
– Priority management between transmission mailboxes
– Autobaud and listening mode
– Low power mode and programmable wake-up on bus activity or by the application
– Data, remote, error and overload frame handling
10.15 Analog-to-Digital Converter
• 8-channel ADC
• 10-bit 384 K samples/sec. Successive Approximation Register ADC
• -3/+3 LSB Integral Non Linearity, -2/+2 LSB Differential Non Linearity
• Integrated 8-to-1 multiplexer, offering eight independent 3.3V analog inputs
• External voltage reference for better accuracy on low voltage inputs
• Individual enable and disable of each channel
• Multiple trigger sources
– Hardware or software trigger
– External trigger pin
– Timer Counter 0 to 2 outputs TIOA0 to TIOA2 trigger
• Sleep Mode and conversion sequencer
– Automatic wakeup on trigger and back to sleep mode after conversions of all
enabled channels
• Four of eight analog inputs shared with digital signals
38
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
11. Package Drawings
Figure 11-1. LQFP Package Drawing
39
6120DS–ATARM–03-Oct-06
Table 11-1.
100-lead LQFP Package Dimensions
Millimeter
Symbol
Min
Nom
A
Inch
Max
Min
Nom
1.60
A1
0.05
A2
1.35
D
1.40
0.63
0.15
0.002
1.45
0.053
0.006
0.055
16.00 BSC
0.630 BSC
D1
14.00 BSC
0.551 BSC
E
16.00 BSC
0.630 BSC
E1
14.00 BSC
R2
0.08
R1
0.08
Q
0°
0°
13°
0°
12°
12°
11°
L
0.45
L1
0.20
b
0.17
e
3.5°
7°
11°
12°
13°
12°
0°
0.60
13°
11°
0.20
0.004
0.75
0.018
1.00 REF
S
0.008
0.003
7°
11°
0.09
0.003
3.5°
θ1
θ3
0.057
0.551 BSC
0.20
θ2
c
Max
13°
0.008
0.024
0.030
0.039 REF
0.008
0.20
0.27
0.007
0.008
0.50 BSC
0.020 BSC
D2
12.00
0.472
E2
12.00
0.472
0.011
Tolerances of Form and Position
40
aaa
0.20
0.008
bbb
0.20
0.008
ccc
0.08
0.003
ddd
0.08
0.003
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
Figure 11-2.
100-TFBGA Package Drawing
All dimensions are in mm
41
6120DS–ATARM–03-Oct-06
12. Ordering Information
Table 12-1.
42
Ordering Information
Temperature
Operating Range
Ordering Code
Package
Package Type
AT91SAM7X512-AU
AT91SAM7X512-CU
LQFP 100
TFBGA 100
Green
Industrial
(-40°C to 85°C)
AT91SAM7X256-AU
AT91SAM7X256-CU
LQFP 100
TFBGA 100
Green
Industrial
(-40°C to 85°C)
AT91SAM7X128-AU
AT91SAM7X128-CU
LQFP 100
TFBGA 100
Green
Industrial
(-40°C to 85°C)
AT91SAM7X512/256/128 Preliminary Summary
6120DS–ATARM–03-Oct-06
AT91SAM7X512/256/128 Preliminary Summary
Revision History
Table 12-2.
Revision History
Doc. Rev
Comments
6120AS
First issue - Unqualified on Intranet
Legal page updated.Qualified on Intranet
6120BS
Corrections to maintain consistency with full datasheet:
In “Features” on page 1, corrected Page Programming Time and Full Erase Time; corrected number of
PDC channels, removed Wake-on-LAN support.
In Figure 2-1 on page 4, corrected number of PDC channels.
In Figure 2-1 on page 4, Table 3-1 on page 5, Table 10-2 on page 33 and Table 10-3 on page 34,
changed all SPI pin names.
In Section 5.2 ”Power Consumption” on page 11, changed value of static current level and value of
dynamic power consumption level on VDDCORE
In Section 6.2 ”Test Pin” on page 13, removed reference to SAM-BA boot recovery.
In Section 6.6 ”I/O Lines Current Drawing” on page 14, changed value of total current level.
In Section 7.4 ”Peripheral DMA Controller” on page 16, corrected number of PDC channels.
In Section 8. ”Memories” on page 17, corrected Page Programming Time and Full Erase Time.
In Section 8.7 ”SAM-BA Boot Assistant” on page 22, updated section.
In Figure 9-1 on page 25, changed range of periph_irq and periph_clk on AIC and for Embedded
Peripherals block.
In Section 10.6 ”Ethernet MAC” on page 35, updated features.
6120CS
Change
Request
Ref.
CSR 05-388
Update to product functionalities including changes to “Features” on page 1, Figure 2-1 on page 4,
Section 9.5 ”Debug Unit” on page 29 and to Peripheral mapping.
05-457
05-462
Updated PLL output range max value in Section 9.2 ”Clock Generator” on page 27.
05-491
Updated information in Section 5.1 ”Power Supplies” on page 11.
Updated ordering information in “Ordering Information” on page 42.
6120DS
Added AT91SAM7X512 to product family.“Features” on page 1 and global
Reformatted Memories Section 8. ”Memories” on page 17.
Reordered sub sections in Peripherals Section 10. ”Peripherals” on page 31
Consolidated Memory Mapping in Figure 8-1 on page 18.
Added TFBGA information Section 4.3 ”100-ball TFBGA Package Outline” on page 10.
added LQFP and TFBGA package drawings Section 11. on page 39.
System Controller block diagram Figure 9-1 on page 25, “ice_nreset” signals changed to
“power_on_reset”.
Section 10.1 ”User Interface” User Peripherals are mapped between 0xF000 0000 and 0XFFFF EFFF.
Table 10-1 on page 31 SYSIRQ changed to SYSC in “Peripheral Identifiers”
05-471
2723
2728
rfo review
43
6120DS–ATARM–03-Oct-06
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High-Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or
otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET
FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER
AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL
ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR
INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make
changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications.
Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
© 2006 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are®, DataFlash ® and others, are registered trademarks SAM-BA ™ and others are trademarks of Atmel Corporation or its subsidiaries. ARM ®, the ARM Powered ® logo and others,
are registered trademarks or trademarks of ARM Limited. Other terms and product names may be the trademarks of others.
6120DS–ATARM–03-Oct-06