ATMEL AT40K05-2BQC

Features
• Ultra High Performance
•
•
•
•
•
•
•
•
•
– System Speeds to 100 MHz
– Array Multipliers > 50 MHz
– 10 ns Flexible SRAM
– Internal Tri-state Capability in Each Cell
FreeRAM™
– Flexible, Single/Dual Port, Synchronous/Asynchronous 10 ns SRAM
– 2,048 - 18,432 Bits of Distributed SRAM Independent of Logic Cells
128 - 384 PCI Compliant I/Os
– 3V/5V Capability
– Programmable Output Drive
– Fast, Flexible Array Access Facilitates Pin Locking
– Pin-compatible with XC4000, XC5200 FPGAs
8 Global Clocks
– Fast, Low Skew Clock Distribution
– Programmable Rising/Falling Edge Transitions
– Distributed Clock Shutdown Capability for Low Power Management
– Global Reset/Asynchronous Reset Options
– 4 Additional Dedicated PCI Clocks
Cache Logic® Dynamic Full/Partial Re-configurability In-System
– Unlimited Re-programmability via Serial or Parallel Modes
– Enables Adaptive Designs
– Enables Fast Vector Multiplier Updates
– QuickChange™ Tools for Fast, Easy Design Changes
Pin-compatible Package Options
– Plastic Leaded Chip Carriers (PLCC)
– Thin, Plastic Quad Flat Packs (LQFP, TQFP, PQFP)
– Ball Grid Arrays (BGAs)
Industry-standard Design Tools
– Seamless Integration (Libraries, Interface, Full Back-annotation) with
Concept®, Everest, Exemplar™, Mentor®, OrCAD®, Synario™, Synopsys®,
Verilog®, Veribest®, Viewlogic®, Synplicity®
– Timing Driven Placement & Routing
– Automatic/Interactive Multi-chip Partitioning
– Fast, Efficient Synthesis
– Over 75 Automatic Component Generators Create 1000s
of Reusable, Fully Deterministic Logic and RAM Functions
Intellectual Property Cores
– Fir Filters, UARTs, PCI, FFT and Other System Level Functions
Easy Migration to Atmel Gate Arrays for High Volume Production
Supply Voltage 5V for AT40K, and 3.3V for AT40KLV
5K - 50K Gates
Coprocessor
FPGA with
FreeRAM™
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
Rev. 0896C–FPGA–04/02
1
Table 1. AT40K/AT40KLV Family(1)
Device
Usable Gates
Rows x Columns
Cells
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
5K - 10K
10K - 20K
20K - 30K
40K - 50K
16 x 16
24 x 24
32 x 32
48 x 48
256
576
1,024
2,304
(1)
(1)
(1)
2,304(1)
Registers
256
576
RAM Bits
2,048
4,608
8,192
18,432
128
192
256
384
I/O (Maximum)
Note:
Description
AT40K05
AT40K05LV
1,024
1. Packages with FCK will have 8 less registers.
The AT40K/AT40KLV is a family of fully PCI-compliant, SRAM-based FPGAs with distributed 10 ns programmable synchronous/asynchronous, dual-port/single-port SRAM,
8 global clocks, Cache Logic ability (partially or fully reconfigurable without loss of data),
automatic component generators, and range in size from 5,000 to 50,000 usable gates.
I/O counts range from 128 to 384 in industry standard packages ranging from 84-pin
PLCC to 352-ball Square BGA, and support 5V designs for AT40K and 3.3V designs for
AT40KLV.
The AT40K/AT40KLV is designed to quickly implement high-performance, large gate
count designs through the use of synthesis and schematic-based tools used on a PC or
Sun platform. Atmel’s design tools provide seamless integration with industry standard
tools such as Synplicity, ModelSim, Exemplar and Viewlogic.
The AT40K/AT40KLV can be used as a coprocessor for high-speed (DSP/processorbased) designs by implementing a variety of computation intensive, arithmetic functions.
These include adaptive finite impulse response (FIR) filters, fast Fourier transforms
(FFT), convolvers, interpolators and discrete-cosine transforms (DCT) that are required
for video compression and decompression, encryption, convolution and other multimedia applications.
Fast, Flexible and
Efficient SRAM
The AT40K/AT40KLV FPGA offers a patented distributed 10 ns SRAM capability where
the RAM can be used without losing logic resources. Multiple independent, synchronous
or asynchronous, dual-port or single-port RAM functions (FIFO, scratch pad, etc.) can
be created using Atmel’s macro generator tool.
Fast, Efficient Array and
Vector Multipliers
The AT40K/AT40KLV’s patented 8-sided core cell with direct horizontal, vertical and
diagonal cell-to-cell connections implements ultra fast array multipliers without using
any busing resources. The AT40K/AT40KLV’s Cache Logic capability enables a large
number of design coefficients and variables to be implemented in a very small amount
of silicon, enabling vast improvement in system speed at much lower cost than conventional FPGAs.
2
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Cache Logic Design
The AT40K/AT40KLV, AT6000 and FPSLIC families are capable of implementing
Cache Logic (dynamic full/partial logic reconfiguration, without loss of data, on-the-fly)
for building adaptive logic and systems. As new logic functions are required, they can be
loaded into the logic cache without losing the data already there or disrupting the operation of the rest of the chip; replacing or complementing the active logic. The
AT40K/AT40KLV can act as a reconfigurable coprocessor.
Automatic Component
Generators
The AT40K/AT40KLV FPGA family is capable of implementing user-defined, automatically generated, macros in multiple designs; speed and functionality are unaffected by
the macro orientation or density of the target device. This enables the fastest, most predictable and efficient FPGA design approach and minimizes design risk by reusing
already proven functions. The Automatic Component Generators work seamlessly with
industry standard schematic and synthesis tools to create the fastest, most efficient
designs available.
The patented AT40K/AT40KLV series architecture employs a symmetrical grid of small
yet powerful cells connected to a flexible busing network. Independently controlled
clocks and resets govern every column of cells. The array is surrounded by programmable I/O.
Devices range in size from 5,000 to 50,000 usable gates in the family, and have 256 to
2,304 registers. Pin locations are consistent throughout the AT40K/AT40KLV series for
easy design migration in the same package footprint. The AT40K/AT40KLV series
FPGAs utilize a reliable 0.6µ single-poly, CMOS process and are 100% factory-tested.
Atmel’s PC- and workstation-based integrated development system (IDS) is used to create AT40K/AT40KLV series designs. Multiple design entry methods are supported.
The Atmel architecture was developed to provide the highest levels of performance,
functional density and design flexibility in an FPGA. The cells in the Atmel array are
small, efficient and can implement any pair of Boolean functions of (the same) three
inputs or any single Boolean function of four inputs. The cell’s small size leads to arrays
with large numbers of cells, greatly multiplying the functionality in each cell. A simple,
high-speed busing network provides fast, efficient communication over medium and
long distances.
3
0896C–FPGA–04/02
The Symmetrical
Array
At the heart of the Atmel architecture is a symmetrical array of identical cells,
see Figure 1. The array is continuous from one edge to the other, except for bus repeaters spaced every four cells, see Figure 2 on page 5. At the intersection of each repeater
row and column there is a 32 x 4 RAM block accessible by adjacent buses. The RAM
can be configured as either a single-ported or dual-ported RAM(1), with either synchronous or asynchronous operation.
Note:
1. The right-most column can only be used as single-port RAM.
Figure 1. Symmetrical Array Surrounded by I/O (AT40K20)
4
= I/O Pad
= Repeater Row
= AT40K Cell
= Repeater Column
= FreeRAM
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Figure 2. Floor Plan (Representative Portion)(1)
RV
= Vertical Repeater
RH
= Horizontal Repeater
= Core Cell
RAM
RV
RV
RV
RAM
RV
RV
RV
RV
RAM
RV
RV
RV
RV
RAM
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RAM
RV
RV
RV
RV
RAM
RV
RV
RV
RV
RAM
RV
RV
RV
RV
RAM
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RAM
RV
RV
RV
RV
RAM
RV
RV
RV
RV
RAM
RV
RV
RV
RV
RAM
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RH
RAM
Note:
RV
RV
RV
RV
RV
RAM
RV
RV
RV
RV
RAM
RV
RV
RV
RV
RAM
1. Repeaters regenerate signals and can connect any bus to any other bus (all pathways are legal) on the same plane. Each repeater has connections to two adjacent
local-bus segments and two express-bus segments. This is done automatically using
the integrated development system (IDS) tool.
5
0896C–FPGA–04/02
The Busing Network
Figure 3 on page 7 depicts one of five identical busing planes. Each plane has three bus
resources: a local-bus resource (the middle bus) and two express-bus (both sides)
resources. Bus resources are connected via repeaters. Each repeater has connections
to two adjacent local-bus segments and two express-bus segments. Each local-bus
segment spans four cells and connects to consecutive repeaters. Each express-bus
segment spans eight cells and “leapfrogs” or bypasses a repeater. Repeaters regenerate signals and can connect any bus to any other bus (all pathways are legal) on the
same plane. Although not shown, a local bus can bypass a repeater via a programmable pass gate allowing long on-chip tri-state buses to be created. Local/Local turns are
implemented through pass gates in the cell-bus interface. Express/Express turns are
implemented through separate pass gates distributed throughout the array.
Some of the bus resources on the AT40K/AT40KLV are used as a dual-function
resources. Table 2 shows which buses are used in a dual-function mode and which bus
plane is used. The AT40K/AT40KLV software tools are designed to accommodate dualfunction buses in an efficient manner.
Table 2. Dual-function Buses
6
Function
Type
Plane(s)
Direction
Comments
Cell Output Enable
Local
5
Horizontal
and Vertical
RAM Output Enable
Express
2
Vertical
Bus full length at array edge
Bus in first column to left of
RAM block
RAM Write Enable
Express
1
Vertical
Bus full length at array edge
Bus in first column to left of
RAM block
RAM Address
Express
1-5
Vertical
Buses full length at array edge
Buses in second column to left
of RAM block
RAM Data In
Local
1
Horizontal
Data In connects to local
bus plane 1
RAM Data Out
Local
2
Horizontal
Data out connects to local
bus plane 2
Clocking
Express
4
Vertical
Bus half length at array edge
Set/Reset
Express
5
Vertical
Bus half length at array edge
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Figure 3. Busing Plane (One of Five)
= AT40K/AT40KLV Core Cell
= Local/Local or Express/Express Turn Point
= Row Repeater
= Column Repeater
Express
Express
Bus
Bus
Local
Bus
7
0896C–FPGA–04/02
Cell Connections
Figure 4(a) depicts direct connections between a cell and its eight nearest neighbors.
Figure 4(b) shows the connections between a cell and five horizontal local buses (1 per
busing plane) and five vertical local buses (1 per busing plane).
CELL
CELL
CELL












Plane 5
Plane 4
Plane 3
Plane 2
Plane 1



Plane 5
Plane 4
Plane 3
Plane 2
Plane 1
Figure 4. Cell Connections




 Horizontal
 Busing Plane














WXYZL
CELL
CELL
W
X
Y
Z
L
CELL
CELL





Diagonal
Direct Connect
CELL
CELL
Orthogonal
Direct Connect
(a) Cell-to-cell Connections
The Cell
Vertical
Busing Plane
CELL
(b) Cell-to-bus Connections
Figure 5 depicts the AT40K/AT40KLV cell. Configuration bits for separate muxes and
pass gates are independent. All permutations of programmable muxes and pass gates
are legal. Vn (V1 - V 5) is connected to the vertical local bus in plane n. H n (H 1 - H5) is
connected to the horizontal local bus in plane n. A local/local turn in plane n is achieved
by turning on the two pass gates connected to Vn and Hn. Pass gates are opened to let
signals into the cell from a local bus or to drive a signal out onto a local bus. Signals
coming into the logic cell on one local bus plane can be switched onto another plane by
opening two of the pass gates. This allows bus signals to switch planes to achieve
greater route ability. Up to five simultaneous local/local turns are possible.
The AT40K/AT40KLV FPGA core cell is a highly configurable logic block based around
two 3-input LUTs (8 x 1 ROM), which can be combined to produce one 4-input LUT.
This means that any core cell can implement two functions of 3 inputs or one function of
4 inputs. There is a Set/Reset D flip-flop in every cell, the output of which may be tristated and fed back internally within the core cell. There is also a 2-to-1 multiplexer in
every cell, and an upstream AND gate in the “front end” of the cell. This AND gate is an
important feature in the implementation of efficient array multipliers.
With this functionality in each core cell, the core cell can be configured in several
“modes”. The core cell flexibility makes the AT40K/AT40KLV architecture well suited to
most digital design application areas, see Figure 6.
8
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Figure 5. The Cell
"1" NW NE SE SW
"1"
"1"
X
N
E
S
W
W
Y
Z
X
W
Y
FB
8X1 LUT
8X1 LUT
OUT
OUT
"1"
"0" "1"
V1
V2
V3
V4
V5
H1
H2
H3
H4
H5
Pass gates
1 0
Z
"1" OEH OEV
D
Q
CLOCK
RESET/SET
Y
X
NW NE SE SW
X
Y
W
Z
FB
L
=
=
=
=
=
N
E
S
W
Diagonal Direct Connect or Bus
Orthogonal Direct Connect or Bus
Bus Connection
Bus Connection
Internal Feedback
9
0896C–FPGA–04/02
A
B
C
D
LUT
Figure 6. Some Single Cell Modes
Q (Registered)
DQ
and/or
Q
LUT
SUM
or
A
B
C
DQ
SUM (Registered)
LUT
LUT
and/or
A
B
C
D
DSP/Multiplier Mode. This mode is used to efficiently
DQ
PRODUCT (Registered) implement array multipliers. An array multiplier is an array
or
of bitwise multipliers, each implemented as a full adder
LUT
LUT
and/or
CARRY
DQ
Q
2:1 MUX
LUT
and/or
A
B
C
Arithmetic Mode is frequently used in many designs.
As can be seen in the figure, the AT40K/AT40KLV core cell
can implement a 1-bit full adder (2-input adder with both
Carry In and Carry Out) in one core cell. Note that the
sum output in this diagram is registered. This output could
then be tri-stated and/or fed back into the cell.
CARRY
PRODUCT
CARRY IN
Synthesis Mode. This mode is particularly important for
the use of VHDL/Verilog design. VHDL/Verilog Synthesis
tools generally will produce as their output large amounts
of random logic functions. Having a 4-input LUT structure
gives efficient random logic optimization without the
delays associated with larger LUT structures. The output
of any cell may be registered, tri-stated and/or fed back
into a core cell.
with an upstream AND gate. Using this AND gate and the
diagonal interconnects between cells, the array multiplier
structure fits very well into the AT40K/AT40KLV
architecture.
Counter Mode. Counters are fundamental to almost all
digital designs. They are the basis of state machines,
timing chains and clock dividers. A counter is essentially
an increment by one function (i.e., an adder), with the
input being an output (or a decode of an output) from the
previous stage. A 1-bit counter can be implemented in one
core cell. Again, the output can be registered, tri-stated
and/or fed back.
CARRY
Q
Tri-state/Mux Mode. This mode is used in many
telecommunications applications, where data needs to be
routed through more than one possible path. The output of
the core cell is very often tri-statable for many inputs to
many outputs data switching.
EN
10
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
RAM
32 x 4 dual-ported RAM blocks are dispersed throughout the array, see Figure 7. A 4-bit
Input Data Bus connects to four horizontal local buses distributed over four sector rows
(plane 1). A 4-bit Output Data Bus connects to four horizontal local buses distributed
over four sectors in the same column. A 5-bit Output Address Bus connects to five vertical express buses in the same column. Ain (input address) and Aout (output address)
alternate positions in horizontally aligned RAM blocks. For the left-most RAM blocks,
Aout is on the left and Ain is on the right. For the right-most RAM blocks, Ain is on the
left and Aout is tied off, thus it can only be configured as a single port. For single-ported
RAM, Ain is the READ/WRITE address port and Din is the (bi-directional) data port.
Right-most RAM blocks can be used only for single-ported memories. WEN and OEN
connect to the vertical express buses in the same column.
Figure 7. RAM Connections (One Ram Block)
CLK
CLK
CLK
CLK
Din
Ain
Dout
Aout
32 x 4 RAM
WEN
OEN
CLK
11
0896C–FPGA–04/02
Reading and writing of the 10 ns 32 x 4 dual-port FreeRAM are independent of each
other. Reading the 32 x 4 dual-port RAM is completely asynchronous. Latches are
transparent; when Load is logic 1, data flows through; when Load is logic 0, data is
latched. These latches are used to synchronize Write Address, Write Enable Not, and
Din signals for a synchronous RAM. Each bit in the 32 x 4 dual-port RAM is also a transparent latch. The front-end latch and the memory latch together form an edge-triggered
flip flop. When a nibble (bit = 7) is (Write) addressed and LOAD is logic 1 and WE is
logic 0, data flows through the bit. When a nibble is not (Write) addressed or LOAD is
logic 0 or WE is logic 1, data is latched in the nibble. The two CLOCK muxes are controlled together; they both select CLOCK (for a synchronous RAM) or they both select
“1” (for an asynchronous RAM). CLOCK is obtained from the clock for the sector-column
immediately to the left and immediately above the RAM block. Writing any value to the
RAM clear byte during configuration clears the RAM (see the “AT40K Configuration
Series” application note at www.atmel.com).
Figure 8. RAM Logic
CLOCK
“1”
0
Ain
Aout
1
1
5
Read Address
Load
Latch
Write Address
32 x 4
Dual-port
RAM
Load
Latch
4
0
Load
5
WEN
Din
“1”
“1” OE
Write Enable NOT
4
Load
Latch
Din
Dout
Dout
Clear
RAM-Clear Byte
Figure 9 on page 13 shows an example of a RAM macro constructed using the
AT40K/AT40KLV’s FreeRAM cells. The macro shown is a 128 x 8 dual-ported asynchronous RAM. Note the very small amount of external logic required to complete the
address decoding for the macro. Most of the logic cells (core cells) in the sectors occupied by the RAM will be unused: they can be used for other logic in the design. This
logic can be automatically generated using the macro generators.
12
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
0896C–FPGA–04/02
Write
Address
2-to-4
Decoder
2-to-4
Decoder
Read
Address
Dout(0)
Din(1)
Dout(1)
Din(2)
Dout(2)
Din(3)
Dout(3)
Din
Ain
Dout
Aout
WEN
OEN
Din
Aout
Dout
Ain
WEN
OEN
Din
Ain
Dout
Aout
WEN
OEN
Din
Aout
Dout
Ain
WEN
OEN
Din(4)
Dout(4)
Din(5)
Dout(5)
Din(6)
Dout(6)
Din(7)
Dout(7)
Din
Ain
WEN
OEN
Dout
Aout
Din
Aout
WEN
OEN
Dout
Ain
Din
Ain
WEN
OEN
Dout
Aout
Din
Aout
WEN
OEN
Dout
Ain
Local Buses
Express Buses
Dedicated Connections
13
AT40K/AT40KLV Series FPGA
Din(0)
Figure 9. RAM Example: 128 x 8 Dual-ported RAM (Asynchronous)
WE
Clocking Scheme
There are eight Global Clock buses (GCK1 - GCK8) on the AT40K/AT40KLV FPGA.
Each of the eight dedicated Global Clock buses is connected to one of the dual-use Global Clock pins. Any clocks used in the design should use global clocks where possible:
this can be done by using Assign Pin Locks to lock the clocks to the Global Clock locations. In addition to the eight Global Clocks, there are four Fast Clocks (FCK1 - FCK4),
two per edge column of the array for PCI specification.
Each column of an array has a “Column Clock mux” and a “Sector Clock mux”. The Column Clock mux is at the top of every column of an array and the Sector Clock mux is at
every four cells. The Column Clock mux is selected from one of the eight Global Clock
buses. The clock provided to each sector column of four cells is inverted, non-inverted
or tied off to “0”, using the Sector Clock mux to minimize the power consumption in a
sector that has no clocks. The clock can either come from the Column Clock or from the
Plane 4 express bus, see Figure 10 on page 15. The extreme-left Column Clock mux
has two additional inputs, FCK1 and FCK2, to provide fast clocking to left-side I/Os. The
extreme-right Column Clock mux has two additional inputs as well, FCK3 and FCK4, to
provide fast clocking to right-side I/Os.
The register in each cell is triggered on a rising clock edge by default. Before configuration on power-up, constant “0” is provided to each register’s clock pins. After
configuration on power-up, the registers either set or reset, depending on the user’s
choice.
The clocking scheme is designed to allow efficient use of multiple clocks with low clock
skew, both within a column and across the core cell array.
14
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Figure 10. Clocking (for One Column of Cells)
}



“1”
FCK (2 per Edge Column of the Array)
GCK1 - GCK8
Column Clock Mux
Sector Clock Mux
Global Clock Line
(Buried)
Express Bus
(Plane 4; Half Length at Edge)
“1”
Repeater
Sector Clock Mux
“1”
“1”
15
0896C–FPGA–04/02
Set/Reset Scheme
The AT40K/AT40KLV family reset scheme is essentially the same as the clock scheme
except that there is only one Global Reset. A dedicated Global Set/Reset bus can be
driven by any User I/O, except those used for clocking (Global Clocks or Fast Clocks).
The automatic placement tool will choose the reset net with the most connections to use
the global resources. You can change this by using an RSBUF component in your
design to indicate the global reset. Additional resets will use the express bus network.
The Global Set/Reset is distributed to each column of the array. Like Sector Clock mux,
there is Sector Set/Reset mux at every four cells. Each sector column of four cells is
set/reset by a Plane 5 express bus or Global Set/Reset using the Sector Set/Reset mux,
see Figure 11 on page 17. The set/reset provided to each sector column of four cells is
either inverted or non-inverted using the Sector Reset mux.
The function of the Set/Reset input of a register is determined by a configuration bit in
each cell. The Set/Reset input of a register is active low (logic 0) by default. Setting or
Resetting of a register is asynchronous. Before configuration on power-up, a logic 1 (a
high) is provided by each register (i.e., all registers are set at power-up).
16
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Figure 11. Set/Reset (for One Column of Cells)
Each Cell has a Programmable Set or Reset
Sector Set/Reset Mux
Repeater
“1”
Global Set/Reset Line (Buried)
“1”
Express Bus
(Plane 5; Half Length at Edge)
“1”
“1”
Any User I/O can Drive Global Set/Reset Lone
17
0896C–FPGA–04/02
I/O Structure
PAD
The I/O pad is the one that connects the I/O to the outside world. Note that not all I/Os
have pads: the ones without pads are called Unbonded I/Os. The number of unbonded
I/Os varies with the device size and package. These unbonded I/Os are used to perform
a variety of bus turns at the edge of the array.
PULL-UP/PULL-DOWN
Each pad has a programmable pull-up and pull-down attached to it. This supplies a
weak “1” or “0” level to the pad pin. When all other drivers are off, this control will dictate
the signal level of the pad pin.
The input stage of each I/O cell has a number of parameters that can be programmed
either as properties in schematic entry or in the I/O Pad Attributes editor in IDS.
TTL/CMOS
The threshold level can be set to either TTL/CMOS-compatible levels.
SCHMITT
A Schmitt trigger circuit can be enabled on the inputs. The Schmitt trigger is a regenerative comparator circuit that adds 1V hysteresis to the input. This effectively improves the
rise and fall times (leading and trailing edges) of the incoming signal and can be useful
for filtering out noise.
DELAYS
The input buffer can be programmed to include four different intrinsic delays as specified
in the AC timing characteristics. This feature is useful for meeting data hold requirements for the input signal.
DRIVE
The output drive capabilities of each I/O are programmable. They can be set to FAST,
MEDIUM or SLOW (using IDS tool). The FAST setting has the highest drive capability
(20 mA at 5V) buffer and the fastest slew rate. MEDIUM produces a medium drive
(14 mA at 5V) buffer, while SLOW yields a standard (6 mA at 5V) buffer.
TRI-STATE
The output of each I/O can be made tri-state (0, 1 or Z), open source (1 or Z) or open
drain (0 or Z) by programming an I/O’s Source Selection mux. Of course, the output can
be normal (0 or 1), as well.
SOURCE SELECTION MUX
The Source Selection mux selects the source for the output signal of an I/O, see
Figure 12 on page 20.
18
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Primary, Secondary and
Corner I/Os
The AT40K/AT40KLV has three kinds of I/Os: Primary I/O, Secondary I/O and a Corner
I/O. Every edge cell except corner cells on the AT40K/AT40KLV has access to one Primary I/O and two Secondary I/Os.
Primary I/O
Every logic cell at the edge of the FPGA array has a direct orthogonal connection to and
from a Primary I/O cell. The Primary I/O interfaces directly to its adjacent core cell. It
also connects into the repeaters on the row immediately above and below the adjacent
core cell. In addition, each Primary I/O also connects into the busing network of the
three nearest edge cells. This is an extremely powerful feature, as it provides logic cells
toward the center of the array with fast access to I/Os via local and express buses. It can
be seen from the diagram that a given Primary I/O can be accessed from any logic cell
on three separate rows or columns of the FPGA. See Figures 12a on page 20 and 13a
on page 21.
Secondary I/O
Every logic cell at the edge of the FPGA array has two direct diagonal connections to a
Secondary I/O cell. The Secondary I/O is located between core cell locations. This I/O
connects on the diagonal inputs to the cell above and the cell below. It also connects to
the repeater of the cell above and below. In addition, each Secondary I/O also connects
into the busing network of the two nearest edge cells. This is an extremely powerful feature, as it provides logic cells toward the center of the array with fast access to I/Os via
local and express buses. It can be seen from the diagram that a given Secondary I/O
can be accessed from any logic cell on two rows or columns of the FPGA. See Figure
12b on page 20 and Figure 13b.
Corner I/O
Logic cells at the corner of the FPGA array have direct-connect access to five separate
I/Os: 2 Primary, 2 Secondary and 1 Corner I/O. Corner I/Os are like an extra Secondary
I/O at each corner of the array. With the inclusion of Corner I/Os, an AT40K/AT40KLV
FPGA with n x n core cells always has 8n I/Os. As the diagram shows, Corner I/Os can
be accessed both from the corner logic cell and the horizontal and vertical busing networks running along the edges of the array. This means that many different edge logic
cells can access the Corner I/Os. See Figure 14 on page 22.
19
0896C–FPGA–04/02
Figure 12. West I/O (Mirrored for East I/O) AT40K/AT40KLV
“0”
“1”
DRIVE
VCC
TRI-STATE
CELL
“0”
PULL-UP
“1”
PAD
CELL
SOURCE
SELECT MUX
SCHMITT
DELAY
TTL/CMOS
GND
PULL-DOWN
CELL
“0”
“1”
CELL
DRIVE
VCC
TRI-STATE
(a) Primary I/O
“0”
PULL-UP
“1”
PAD
SOURCE
DELAY SELECT MUX
TTL/CMOS
SCHMITT
DELAY
GND
PULL-DOWN
CELL
(b) Secondary I/O
20
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Figure 13. South I/O (Mirrored for North I/O) AT40K/AT40KLV
“0”
“1”
DRIVE
VCC
TRI-STATE
CELL
“0”
PULL-UP
“1”
PAD
CELL
SOURCE SELECT MUX
DELAY
SCHMITT
GND
TTL/CMOS
PULL-DOWN
CELL
“0”
“1”
CELL
DRIVE
VCC
TRI-STATE
(a) Primary I/O
“0”
PULL-UP
“1”
PAD
SOURCE SELECT MUX
DELAY
SCHMITT
TTL/CMOS
GND
PULL-DOWN
CELL
(a) Secondary I/O
21
0896C–FPGA–04/02
“0”
“1”
“0”
“1”
“0”
“1”
DRIVE
PULL-DOWN
GND
TTL/CMOS
DRIVE
SCHMITT
DELAY
“0”
“1”
DRIVE
TRI-STATE
VCC
TTL/CMOS
SCHMITT
TRI-STATE
DELAY
TRI-STATE
VCC
PULL-UP
GND
PAD
“1”
VCC
“0”
PAD
PULL-DOWN
PULL-UP
Figure 14. Northwest Corner (Similar for NE/SE/SW Corners) AT40K/AT40KLV
“0”
PULL-UP
“1”
PAD
CELL
CELL
SCHMITT
DELAY
TTL/CMOS
GND
PULL-DOWN
CELL
22
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Absolute Maximum Ratings – 5V Commercial/Industrial* AT40K
Operating Temperature.................................. -55°C to +125 °C
*NOTICE:
Storage Temperature ..................................... -65 °C to +150°C
Voltage on Any Pin
with Respect to Ground .................................-0.5V to V CC +7V
Supply Voltage (VCC ) .........................................-0.5V to +7.0V
Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those listed under operating conditions is not implied. Exposure to Absolute Maximum Rating conditions for extended
periods of time may affect device reliability.
Maximum Soldering Temp. (10 sec. @ 1/16 in.)............. 250°C
ESD (RZAP = 1.5K, CZAP = 100 pF)................................. 2000V
DC and AC Operating Range – 5V Operation AT40K
Commercial -2
Industrial -2
Military -2
0°C - 70°C
-40°C - 85°C
-55°C - 125°C
5V ± 5%
5V ± 10%
5V ± 10%
High (VIHT)
2.0V - VCC
2.0V - V CC
2.0V - VCC
Low (VILT)
0V - 0.8V
0V - 0.8V
0V - 0.8V
High (VIHC)
70% - 100% VCC
70% - 100% VCC
70% - 100% VCC
Low (VILC)
0 - 30% VCC
0 - 30% VCC
0 - 30% VCC
Operating Temperature (Case)
VCC Power Supply
Input Voltage Level (TTL)
Input Voltage Level (CMOS)
23
0896C–FPGA–04/02
DC Characteristics – 5V Operation Commercial/Industrial/Military AT40K
Symbol
Parameter
VIH
High-level Input Voltage
VIL
Low-level Input Voltage
Conditions
Minimum
CMOS
70% VCC
V
TTL
2.0
V
CMOS
-0.3
30% VCC
V
TTL
-0.3
0.8
V
IOH = 6mA
VCC = VCC Minimum
VOH
High-level Output Voltage
IOH = 14mA
VCC = VCC Minimum
IOH = 20mA
Commercial = 4.75V
Industrial/Military = 4.5V
VOL
Low-level Output Voltage
IIH
High-level Input Current
IIL
Low-level Input Current
IOZH
IOZL
High-level Tri-state Output
Leakage Current
Low-level Tri-state Output
Leakage Current
Maximum
Units
Ind. = 3.15
4.0
Con = 3.325
V
Ind. = 3.15
4.0
Con = 3.325
V
Ind. = 3.15
4.0
Con = 3.325
V
IOL = -6mA
Commercial = 4.75V
Industrial/Military = 4.5V
0.4
V
IOL = -14mA
Commercial = 4.75V
Industrial/Military = 4.5V
0.4
V
IOL = -20mA
Commercial = 4.75V
Industrial/Military = 4.5V
0.4
V
VIN = VCC Maximum
10.0
µA
500.0
µA
With pull-down, VIN = V CC
125.0
VIN = VSS
-10.0
With pull-up, VIN = VSS
CON = -1 mA
to -250 µA
250.0
µA
-250.0
Without pull-down, VIN = VCC
With pull-down, VIN = V CC
125.0
Without pull-up, VIN = VSS
Maximum
-10.0
With pull-up, VIN = VSS
Maximum
-500.0
ICC
Standby Current Consumption
Standby, unprogrammed
CIN
Input Capacitance
All pins
24
Typical
250.0
CON = -1 mA
to -250 µA
µA
10.0
µA
500.0
µA
µA
-250.0
-125.0
µA
0.6
1.0
mA
10.0
pF
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AC Timing Characteristics – 5V Operation AT40K
Delays are based on fixed loads and are described in the notes.
Maximum times based on worst case: VCC = 4.75V, temperature = 70°C
Minimum times based on best case: VCC = 5.25V, temperature = 0°C
Maximum delays are the average of tPDLH and tPDHL.
Cell Function
Parameter
Path
-2
Units
Notes
2-input Gate
tPD (Maximum)
x/y -> x/y
1.8
ns
1 unit load
3-input Gate
tPD (Maximum)
x/y/z -> x/y
2.1
ns
1 unit load
3-input Gate
tPD (Maximum)
x/y/w -> x/y
2.2
ns
1 unit load
4-input Gate
tPD (Maximum)
x/y/w/z -> x/y
2.2
ns
1 unit load
Fast Carry
tPD (Maximum)
y -> y
1.4
ns
1 unit load
Fast Carry
tPD (Maximum)
x -> y
1.7
ns
1 unit load
Fast Carry
tPD (Maximum)
y -> x
1.8
ns
1 unit load
Fast Carry
tPD (Maximum)
x -> x
1.5
ns
1 unit load
Fast Carry
tPD (Maximum)
w -> y
2.2
ns
1 unit load
Fast Carry
tPD (Maximum)
w -> x
2.3
ns
1 unit load
Fast Carry
tPD (Maximum)
z -> y
2.3
ns
1 unit load
Fast Carry
tPD (Maximum)
z -> x
1.7
ns
1 unit load
DFF
tPD (Maximum)
q -> x/y
1.8
ns
1 unit load
DFF
tPD (Maximum)
R -> x/y
2.2
ns
1 unit load
DFF
tPD (Maximum)
S -> x/y
2.2
ns
1 unit load
DFF
tPD (Maximum)
q -> w
1.8
ns
Incremental -> L
tPD (Maximum)
x/y -> L
1.5
ns
1 unit load
Local Output Enable
tPZX (Maximum)
oe -> L
1.4
ns
1 unit load
Local Output Enable
tPXZ (Maximum)
oe -> L
1.8
ns
Core
25
0896C–FPGA–04/02
AC Timing Characteristics – 5V Operation AT40K
Delays are based on fixed loads and are described in the notes.
Maximum times based on worst case: VCC = 4.75V, temperature = 70°C
Minimum times based on best case: VCC = 5.25V, temperature = 0°C
Maximum delays are the average of tPDLH and tPDHL.
All input IO characteristics measured from a VIH of 50% of VDD at the pad (CMOS threshold) to the internal VIH of 50%
of VCC. All output IO characteristics are measured as the average of tPDLH and tPDHL to the pad VIH of 50% of VCC.
Cell Function
Parameter
Path
-2
Units
Notes
Repeater
tPD (Maximum)
L -> E
1.3
ns
1 unit load
Repeater
tPD (Maximum)
E -> E
1.3
ns
1 unit load
Repeater
tPD (Maximum)
L -> L
1.3
ns
1 unit load
Repeater
tPD (Maximum)
E -> L
1.3
ns
1 unit load
Repeater
tPD (Maximum)
E -> IO
0.8
ns
1 unit load
Repeater
tPD (Maximum)
L -> IO
0.8
ns
1 unit load
Repeaters
All input IO characteristics measured from a VIH of 50% at the pad (CMOS threshold) to the internal VIH of 50% of VCC. All
output IO characteristics are measured as the average of tPDLH and tPDHL to the pad VIH of 50% of VCC.
Cell Function
Parameter
Path
-2
Units
Notes
Input
tPD (Maximum)
pad -> x/y
1.2
ns
No extra delay
Input
tPD (Maximum)
pad -> x/y
3.6
ns
1 extra delay
Input
tPD (Maximum)
pad -> x/y
7.3
ns
2 extra delays
Input
tPD (Maximum)
pad -> x/y
10.8
ns
3 extra delays
Output, Slow
tPD (Maximum)
x/y/E/L -> pad
5.9
ns
50 pf load
Output, Medium
tPD (Maximum)
x/y/E/L -> pad
4.8
ns
50 pf load
Output, Fast
tPD (Maximum)
x/y/E/L -> pad
3.9
ns
50 pf load
Output, Slow
tPZX (Maximum)
oe -> pad
6.2
ns
50 pf load
Output, Slow
tPXZ (Maximum)
oe -> pad
1.3
ns
50 pf load
Output, Medium
tPZX (Maximum)
oe -> pad
4.8
ns
50 pf load
Output, Medium
tPXZ (Maximum)
oe -> pad
1.9
ns
50 pf load
Output, Fast
tPZX (Maximum)
oe -> pad
3.7
ns
50 pf load
Output, Fast
tPXZ (Maximum)
oe -> pad
1.6
ns
50 pf load
IO
26
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AC Timing Characteristics – 5V Operation AT40K
Delays are based on fixed loads and are described in the notes.
Maximum times based on worst case: VCC = 4.75V, temperature = 70°C
Minimum times based on best case: VCC = 5.25V, temperature = 0°C
Maximum delays are the average of tPDLH and tPDHL.
Clocks and Reset Input buffers are measured from a VIH of 1.5V at the input pad to the internal VIH of 50% of VCC.
Maximum times for clock input buffers and internal drivers are measured for rising edge delays only.
Cell Function
Parameter
Path
Device
-2
Units
Notes
Global Clocks and Set/Reset
GCLK Input Buffer
tPD (Maximum)
pad -> clock
pad -> clock
pad -> clock
pad -> clock
AT40K05
AT40K10
AT40K20
AT40K40
1.1
1.2
1.2
1.4
ns
ns
ns
ns
Rising edge clock
FCLK Input Buffer
tPD (Maximum)
pad -> clock
pad -> clock
pad -> clock
pad -> clock
AT40K05
AT40K10
AT40K20
AT40K40
0.7
0.8
0.8
0.8
ns
ns
ns
ns
Rising edge clock
Clock Column Driver
tPD (Maximum)
clock -> colclk
clock -> colclk
clock -> colclk
clock -> colclk
AT40K05
AT40K10
AT40K20
AT40K40
0.8
0.9
1.0
1.1
ns
ns
ns
ns
Rising edge clock
Clock Sector Driver
tPD (Maximum)
colclk -> secclk
colclk -> secclk
colclk -> secclk
colclk -> secclk
AT40K05
AT40K10
AT40K20
AT40K40
0.5
0.5
0.5
0.5
ns
ns
ns
ns
Rising edge clock
GSRN Input Buffer
tPD (Maximum)
pad -> GSRN
pad -> GSRN
pad -> GSRN
pad -> GSRN
AT40K05
AT40K10
AT40K20
AT40K40
3.0
3.7
4.3
5.6
ns
ns
ns
ns
From any pad to Global
Set/Reset network
Global Clock to Output
tPD (Maximum)
clock pad -> out
clock pad -> out
clock pad -> out
clock pad -> out
AT40K05
AT40K10
AT40K20
AT40K40
8.3
8.4
8.6
8.8
ns
ns
ns
ns
Rising edge clock
Fully loaded clock tree
Rising edge DFF
20 mA output buffer
50 pf pin load
Fast Clock to Output
tPD (Maximum)
clock pad -> out
clock pad -> out
clock pad -> out
clock pad -> out
AT40K05
AT40K10
AT40K20
AT40K40
7.9
8.0
8.1
8.3
ns
ns
ns
ns
Rising edge clock
Fully loaded clock tree
Rising edge DFF
20 mA output buffer
50 pf pin load
27
0896C–FPGA–04/02
AC Timing Characteristics – 5V Operation AT40K
Delays are based on fixed loads and are described in the notes.
Maximum times based on worst case: VCC = 4.75V, temperature = 70°C
Minimum times based on best case: VCC = 5.25V, temperature = 0°C
Maximum delays are the average of tPDLH and tPDHL.
Cell Function
Parameter
Path
-2
Units
Notes
Write
tWECYC (Minimum)
cycle time
8.0
ns
Write
tWEL (Minimum)
we
3.0
ns
Pulse width low
Write
tWEH (Minimum)
we
3.0
ns
Pulse width high
Write
tAWS (Minimum)
wr addr setup -> we
2.0
ns
Write
tAWH (Minimum)
wr addr hold -> we
0.0
ns
Write
tDS (Minimum)
din setup -> we
2.0
ns
Write
tDH (Minimum)
din hold -> we
0.0
ns
Write/Read
tDD (Maximum)
din -> dout
4.6
ns
Read
tAD (Maximum)
rd addr -> dout
3.1
ns
Read
tOZX (Maximum)
oe -> dout
1.6
ns
Read
tOXZ (Maximum)
oe -> dout
2.0
ns
Write
tCYC (Minimum)
cycle time
8.0
ns
Write
tCLKL (Minimum)
clk
3.0
ns
Pulse width low
Write
tCLKH (Minimum)
clk
3.0
ns
Pulse width high
Write
tWCS (Minimum)
we setup -> clk
2.0
ns
Write
tWCH (Minimum)
we hold -> clk
0.0
ns
Write
tACS (Minimum)
wr addr setup -> clk
2.0
ns
Write
tACH (Minimum)
wr addr hold -> clk
0.0
ns
Write
tDCS (Minimum)
wr data setup -> clk
2.0
ns
Write
tDCH (Minimum)
wr data hold -> clk
0.0
ns
Write/Read
tCD (Maximum)
clk -> dout
3.5
ns
Read
tAD (Maximum)
rd addr -> dout
3.1
ns
Read
tOZX (Maximum)
oe -> dout
1.6
ns
Read
tOXZ (Maximum)
oe -> dout
2.0
ns
Async RAM
rd addr = wr addr
Sync RAM
28
rd addr = wr addr
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
FreeRAM Asynchronous Timing Characteristics
Single-port Write/Read
tWEL
WE
ADDR
tAWS
tAWH
0
1
2
3
tOH
OE
tOXZ
tDS
tOZX
tDH
tAD
DATA
Dual-port Write with
Read
tWECYC
tWEH
tWEL
WE
WR ADDR
tAWS
tAWH
0
1
2
tDH
WR DATA
PREV.
NEW
tDD
RD ADDR
RD DATA
= WR ADDR 1
tWD
OLD
PREV.
NEW
Dual-port Read
0
RD ADDR
1
OE
tOZX
tAD
tOXZ
DATA
29
0896C–FPGA–04/02
FreeRAM Synchronous Timing Characteristics
Single-port Write/Read
tCLKH
CLK
tWCS
tWCH
tACS
tACH
WE
ADDR
0
1
3
2
OE
tOXZ
tDCS
tDCH
tOZX
tAD
DATA
Dual-port Write with
Read
tCYC
tCLKH
tCLKL
CLK
tWCS
tWCH
tACS
tACH
WE
WR ADDR
0
1
2
tDCS
tDCH
WR DATA
RD ADDR
= WR ADDR 1
tCD
RD DATA
Dual-port Read
0
RD ADDR
1
OE
tOZX
tAD
tOXZ
DATA
30
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Absolute Maximum Ratings – 3.3V Commercial/Industrial* AT40KLV
Operating Temperature.................................. -55°C to +125 °C
Storage Temperature ..................................... -65 °C to +150°C
Voltage on Any Pin
with Respect to Ground .................................-0.5V to V CC +7V
Supply Voltage (VCC ) .........................................-0.5V to +7.0V
*NOTICE:
Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those listed under operating conditions is not implied. Exposure to Absolute Maximum Rating conditions for extended
periods of time may affect device reliability.
Maximum Soldering Temp. (10 sec. @ 1/16 in.)............. 250°C
ESD (RZAP = 1.5K, CZAP = 100 pF)................................. 2000V
DC and AC Operating Range – 3.3V Operation AT40KLV
Commercial
Industrial
0°C - 70°C
-40°C - 85°C
3.3V ± 0.3V
3.3V ± 0.3V
High (VIHC)
70% - 100% VCC
70% - 100% VCC
Low (VILC)
0 - 30% VCC
0 - 30% V CC
Operating Temperature (Case)
VCC Power Supply
Input Voltage Level (CMOS)
31
0896C–FPGA–04/02
DC Characteristics – 3.3V Operation Commercial/Industrial AT40KLV
Symbol
Parameter
VIH
High-level Input Voltage
VIL
Low-level Input Voltage
VOH
VOL
High-level Output Voltage
Low-level Output Voltage
IIH
High-level Input Current
IIL
Low-level Input Current
IOZH
High-level Tri-state Output
Leakage Current
IOZL
Low-level Tri-state Output
Leakage Current
Conditions
Minimum
CMOS
70% VCC
V
TTL
2.0
V
CMOS
-0.3
30% VCC
V
TTL
-0.3
0.8
V
IOH = 4 mA
VCC = VCC Minimum
2.1
V
IOH = 12 mA
VCC = 3.0V
2.1
V
IOH = 16 mA
VCC = 3.0V
2.1
V
Units
0.4
V
IOL = -12 mA
VCC = 3.0V
0.4
V
IOL = -16 mA
VCC = 3.0V
0.4
V
VIN = VCC Maximum
10.0
µA
300.0
µA
With pull-down, VIN = V CC
75.0
VIN = VSS
-10.0
With pull-up, VIN = VSS
-300.0
150.0
µA
-150.0
Without pull-down,
VIN = VCC Maximum
With pull-down,
VIN = VCC Maximum
75.0
Without pull-up, VIN = VSS
-10.0
With pull-up, VIN = VSS
Standby Current
Consumption
Standby, unprogrammed
CIN
Input Capacitance
All pins
32
Maximum
IOL = -4 mA
VCC = 3.0V
ICC
Note:
Typical
CON = -500 µA
TO -125 µA
150.0
-75.0
µA
10.0
µA
300.0
µA
mA
-150.0
CON = -500 µA
TO -125 µA-
µA
0.6
1.0
mA
10.0
pF
1. Parameter based on characterization and simulation; it is not tested in production.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AC Timing Characteristics – 3.3V Operation AT40KLV
Delays are based on fixed loads and are described in the notes.
Maximum times based on worst case: VCC = 3.00V, temperature = 70°C
Minimum times based on best case: VCC = 3.60V, temperature = 0°C
Maximum delays are the average of tPDLH and tPDHL.
Cell Function
Parameter
Path
-3
Units
Notes
2-input Gate
tPD (Maximum)
x/y -> x/y
2.9
ns
1 unit load
3-input Gate
tPD (Maximum)
x/y/z -> x/y
2.8
ns
1 unit load
3-input Gate
tPD (Maximum)
x/y/w -> x/y
3.4
ns
1 unit load
4-input Gate
tPD (Maximum)
x/y/w/z -> x/y
3.4
ns
1 unit load
Fast Carry
tPD (Maximum)
y -> y
2.3
ns
1 unit load
Fast Carry
tPD (Maximum)
x -> y
2.9
ns
1 unit load
Fast Carry
tPD (Maximum)
y -> x
3.0
ns
1 unit load
Fast Carry
tPD (Maximum)
x -> x
2.3
ns
1 unit load
Fast Carry
tPD (Maximum)
w -> y
3.4
ns
1 unit load
Fast Carry
tPD (Maximum)
w -> x
3.4
ns
1 unit load
Fast Carry
tPD (Maximum)
z -> y
3.4
ns
1 unit load
Fast Carry
tPD (Maximum)
z -> x
2.4
ns
1 unit load
DFF
tPD (Maximum)
q -> x/y
2.8
ns
1 unit load
DFF
tPD (Maximum)
R -> x/y
3.2
ns
1 unit load
DFF
tPD (Maximum)
S -> x/y
3.0
ns
1 unit load
DFF
tPD (Maximum)
q -> w
2.7
ns
Incremental -> L
tPD (Maximum)
x/y -> L
2.4
ns
1 unit load
Local Output Enable
tPZX (Maximum)
oe -> L
2.8
ns
1 unit load
Local Output Enable
tPXZ (Maximum)
oe -> L
2.4
ns
Core
33
0896C–FPGA–04/02
AC Timing Characteristics – 3.3V Operation AT40KLV
Delays are based on fixed loads and are described in the notes.
Maximum times based on worst case: VCC = 3.0V, temperature = 70°C
Minimum times based on best case: VCC = 3.6V, temperature = 0°C
Maximum delays are the average of tPDLH and tPDHL.
All input IO characteristics measured from a VIH of 50% of VDD at the pad (CMOS threshold) to the internal VIH of 50% of
VDD. All output IO characteristics are measured as the average of tPDLH and tPDHL to the pad VIH of 50% of VDD.
Cell Function
Parameter
Path
-3
Units
Notes
Repeater
tPD (Maximum)
L -> E
2.2
ns
1 unit load
Repeater
tPD (Maximum)
E -> E
2.2
ns
1 unit load
Repeater
tPD (Maximum)
L -> L
2.2
ns
1 unit load
Repeater
tPD (Maximum)
E -> L
2.2
ns
1 unit load
Repeater
tPD (Maximum)
E -> IO
1.4
ns
1 unit load
Repeater
tPD (Maximum)
L -> IO
1.4
ns
1 unit load
Repeaters
All input IO characteristics measured from a VIH of 50% of VDD at the pad (CMOS threshold) to the internal VIH of 50% of
VDD. All output IO characteristics are measured as the average of tPDLH and tPDHL to the pad VIH of 50% of VDD.
Cell Function
Parameter
Path
-3
Units
Notes
Input
tPD (Maximum)
pad -> x/y
1.9
ns
No extra delay
Input
tPD (Maximum)
pad -> x/y
5.8
ns
1 extra delay
Input
tPD (Maximum)
pad -> x/y
11.5
ns
2 extra delays
Input
tPD (Maximum)
pad -> x/y
17.4
ns
3 extra delays
Output, Slow
tPD (Maximum)
x/y/E/L -> pad
9.1
ns
50 pf load
Output, Medium
tPD (Maximum)
x/y/E/L -> pad
7.6
ns
50 pf load
Output, Fast
tPD (Maximum)
x/y/E/L -> pad
6.2
ns
50 pf load
Output, Slow
tPZX (Maximum)
oe -> pad
9.5
ns
50 pf load
Output, Slow
tPXZ (Maximum)
oe -> pad
2.1
ns
50 pf load
Output, Medium
tPZX (Maximum)
oe -> pad
7.4
ns
50 pf load
Output, Medium
tPXZ (Maximum)
oe -> pad
2.7
ns
50 pf load
Output, Fast
tPZX (Maximum)
oe -> pad
5.9
ns
50 pf load
Output, Fast
tPXZ (Maximum)
oe -> pad
2.4
ns
50 pf load
IO
34
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AC Timing Characteristics – 3.3V Operation AT40KLV
Delays are based on fixed loads and are described in the notes.
Maximum times based on worst case: VCC = 3.0V, temperature = 70°C
Minimum times based on best case: VCC = 3.6V, temperature = 0°C
Maximum delays are the average of tPDLH and tPDHL.
Clocks and Reset Input buffers are measured from a VIH of 1.5V at the input pad to the internal VIH of 50% of VCC.
Maximum times for clock input buffers and internal drivers are measured for rising edge delays only.
Cell Function
Parameter
Path
Device
-3
Units
Notes
Global Clocks and Set/Reset
GCK Input Buffer
tPD
(Maximum)
pad -> clock
pad -> clock
pad -> clock
pad -> clock
AT40K05LV
AT40K10LV
AT40K20LV
AT40K40LV
1.3
1.5
1.6
1.9
ns
ns
ns
ns
Rising edge clock
FCK Input Buffer
tPD
(Maximum)
pad -> clock
pad -> clock
pad -> clock
pad -> clock
AT40K05LV
AT40K10LV
AT40K20LV
AT40K40LV
0.7
0.8
0.8
0.9
ns
ns
ns
ns
Rising edge clock
Clock Column Driver
tPD
(Maximum)
clock -> colclk
clock -> colclk
clock -> colclk
clock -> colclk
AT40K05LV
AT40K10LV
AT40K20LV
AT40K40LV
1.5
1.8
2.0
2.5
ns
ns
ns
ns
Rising edge clock
Clock Sector Driver
tPD
(Maximum)
colclk -> secclk
colclk -> secclk
colclk -> secclk
colclk -> secclk
AT40K05LV
AT40K10LV
AT40K20LV
AT40K40LV
1.0
1.0
1.0
1.0
ns
ns
ns
ns
Rising edge clock
GSRN Input Buffer
tPD
(Maximum)
pad -> GSRN
pad -> GSRN
pad -> GSRN
pad -> GSRN
AT40K05LV
AT40K10LV
AT40K20LV
AT40K40LV
4.5
5.4
6.3
8.2
ns
ns
ns
ns
Global Clock to Output
tPD
(Maximum)
clock pad -> out
clock pad -> out
clock pad -> out
clock pad -> out
AT40K05LV
AT40K10LV
AT40K20LV
AT40K40LV
13.0
13.4
13.8
14.5
ns
ns
ns
ns
Rising edge clock
Fully loaded clock tree
Rising edge DFF
20 mA output buffer
50 pf pin load
Fast Clock to Output
tPD
(Maximum)
clock pad -> out
clock pad -> out
clock pad -> out
clock pad -> out
AT40K05LV
AT40K10LV
AT40K20LV
AT40K40LV
12.4
12.7
13.0
13.5
ns
ns
ns
ns
Rising edge clock
Fully loaded clock tree
Rising edge DFF
20 mA output buffer
50 pf pin load
35
0896C–FPGA–04/02
AC Timing Characteristics – 3.3V Operation AT40KLV
Delays are based on fixed loads and are described in the notes.
Maximum times based on worst case: VCC = 3.0V, temperature = 70°C
Minimum times based on best case: VCC = 3.6V, temperature = 0°C
Cell Function
Parameter
Path
-3
Units
Write
tWECYC (Minimum)
Write
Notes
cycle time
12.0
ns
tWEL (Minimum)
we
5.0
ns
Pulse width low
Write
tWEH (Minimum)
we
5.0
ns
Pulse width high
Write
tAWS (Minimum)
wr addr setup -> we
5.3
ns
Write
tAWH (Minimum)
wr addr hold -> we
0.0
ns
Write
tDS (Minimum)
din setup -> we
5.0
ns
Write
tDH (Minimum)
din hold -> we
0.0
ns
Write/Read
tDD (Maximum)
din -> dout
8.7
ns
Read
tAD (Maximum)
rd addr -> dout
6.3
ns
Read
tOZX (Maximum)
oe -> dout
2.9
ns
Read
tOXZ (Maximum)
oe -> dout
3.5
ns
Write
tCYC (Minimum)
cycle time
12.0
ns
Write
tCLKL (Minimum)
clk
5.0
ns
Pulse width low
Write
tCLKH (Minimum)
clk
5.0
ns
Pulse width high
Write
tWCS(Minimum)
we setup -> clk
3.2
ns
Write
tWCH (Minimum)
we hold -> clk
0.0
ns
Write
tACS (Minimum)
wr addr setup -> clk
5.0
ns
Write
tACH (Minimum)
wr addr hold -> clk
0.0
ns
Write
tDCS (Minimum)
wr data setup -> clk
3.9
ns
Write
tDCH (Minimum)
wr data hold -> clk
0.0
ns
Write/Read
tCD (Maximum)
clk -> dout
5.8
ns
Read
tAD (Maximum)
rd addr -> dout
6.3
ns
Read
tOZX (Maximum)
oe -> dout
2.9
ns
Read
tOXZ (Maximum)
oe -> dout
3.5
ns
Async RAM
rd addr = wr addr
Sync RAM
Notes:
36
1.
2.
3.
4.
rd addr = wr addr
CMOS buffer delays are measured from a VIH of 1/2 VCC at the pad to the internal VIH at A. The input buffer load is constant.
Buffer delay is to a pad voltage of 1.5V with one output switching.
Parameter based on characterization and simulation; not tested in production.
Exact power calculation is available in Atmel FPGA Designer software.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
Left Side (Top to Bottom)
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
128 I/O
192 I/O
256 I/O
384 I/O
84
PLCC
GND
GND
GND
GND
12
4
1
1
1
2
1
304
GND(1)
I/O1,
GCK1
(A16)
I/O1,
GCK1
(A16)
I/O1,
GCK1
(A16)
I/O1,
GCK1
(A16)
13
5
2
2
2
4
2
303
D23
I/O2
(A17)
I/O2
(A17)
I/O2
(A17)
I/O2
(A17)
14
6
3
3
3
5
3
302
C25
I/O3
I/O3
I/O3
I/O3
4
4
6
4
301
D24
I/O4
I/O4
I/O4
I/O4
5
5
7
5
300
E23
I/O5
(A18)
I/O5
(A18)
I/O5
(A18)
I/O5
(A18)
15
7
4
6
6
8
6
299
C26
I/O6
(A19)
I/O6
(A19)
I/O6
(A19)
I/O6
(A19)
16
8
5
7
7
9
7
298
E24
GND
I/O7
I/O8
I/O9
D25
I/O10
F23
I/O7
I/O11
297
F24
I/O8
I/O12
296
E25
VCC
VCC
VCC(1)
GND
GND
GND(1)
I/O13
I/O14
I/O7
I/O7
I/O9
I/O15
8
10
8
295
D26
I/O8
I/O8
I/O10
I/O16
9
11
9
294
G24
I/O9
I/O11
I/O17
12
10
293
F25
I/O10
I/O12
I/O18
13
11
292
F26
I/O21
12
291
H23
13
GND
I/O19
I/O20
I/O11
I/O12
I/O13
I/O14
I/O22
290
H24
I/O15
I/O23
289
G25
I/O16
I/O24
288
G26
GND
GND
GND
GND
8
10
14
14
287
GND(1)
I/O9,
FCK1
I/O13,
FCK1
I/O17,
FCK1
I/O25,
FCK1
9
11
15
15
286
J23
I/O10
I/O14
I/O18
I/O26
10
12
16
16
285
J24
Notes:
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
3. On-chip tri-state.
37
0896C–FPGA–04/02
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O11
(A20)
I/O15
(A20)
I/O19
(A20)
I/O12
(A21)
I/O16
(A21)
Left Side (Top to Bottom)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
I/O27
(A20)
17
9
6
11
13
17
17
284
H25
I/O20
(A21)
I/O28
(A21)
18
10
7
12
14
18
18
283
K23
VCC
VCC
VCC
19
282
VCC(1)
I/O17
I/O21
I/O29
20
280
K24
I/O18
I/O22
I/O30
21
279
J25
GND
I/O31
I/O32
I/O33
J26
I/O34
L23
I/O23
I/O35
278
L24
I/O24
I/O36
277
K25
GND
GND
GND(1)
22
VCC(1)
VCC
I/O37
I/O38
I/O25
I/O39
276
L25
I/O26
I/O40
275
L26
I/O19
I/O27
I/O41
19
23
274
M23
I/O20
I/O28
I/O42
20
24
273
M24
I/O13
I/O21
I/O29
I/O43
I/O14
I/O22
I/O30
I/O44
GND
13
15
21
25
272
M25
11
8
14
16
22
26
271
M26
I/O45
I/O46
I/O15
(A22)
I/O23
(A22)
I/O31
(A22)
I/O47
(A22)
19
12
9
15
17
23
27
270
N24
I/O16
(A23)
I/O24
(A23)
I/O32
(A23)
I/O48
(A23)
20
13
10
16
18
24
28
269
N25
GND
GND
GND
GND
21
14
11
17
19
25
29
268
GND(1)
VCC
VCC
VCC
VCC
22
15
12
18
20
26
30
267
VCC(1)
I/O17
I/O25
I/O33
I/O49
23
16
13
19
21
27
31
266
N26
I/O18
I/O26
I/O34
I/O50
24
17
14
20
22
28
32
265
P25
18
15
21
23
29
33
264
P23
I/O51
I/O52
I/O19
Notes:
38
I/O27
I/O35
I/O53
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
3. On-chip tri-state.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O20
I/O28
I/O36
I/O54
Left Side (Top to Bottom)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
22
24
30
34
263
P24
GND
I/O29
I/O37
I/O55
31
35
262
R26
I/O30
I/O38
I/O56
32
36
261
R25
I/O39
I/O57
260
R24
I/O40
I/O58
259
R23
I/O59
I/O60
VCC(1)
VCC
GND(1)
GND
GND
37
I/O41
I/O61
258
T26
I/O42
I/O62
257
T25
I/O63
I/O64
I/O65
T24
I/O66
U25
GND
I/O31
I/O43
I/O67
38
256
T23
I/O32
I/O44
I/O68
39
255
V26
VCC
VCC
VCC
40
253
VCC(1)
I/O21
I/O33
I/O45
I/O69
25
19
16
23
25
33
41
252
U24
I/O22
I/O34
I/O46
I/O70
26
20
17
24
26
34
42
251
V25
I/O23
I/O35
I/O47
I/O71
25
27
35
43
250
V24
I/O24,
FCK2
I/O36,
FCK2
I/O48,
FCK2
I/O72,
FCK2
26
28
36
44
249
U23
GND
GND
GND
GND
27
29
37
45
248
GND(1)
I/O49
I/O73
247
Y26
I/O50
I/O74
246
W25
I/O37
I/O51
I/O75
46
245
W24
I/O38
I/O52
I/O76
47
244
V23
I/O77
I/O78
GND
I/O79
I/O80
Notes:
I/O39
I/O53
I/O81
38
48
243
AA26
I/O40
I/O54
I/O82
39
49
242
Y25
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
3. On-chip tri-state.
39
0896C–FPGA–04/02
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
Left Side (Top to Bottom)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
I/O25
I/O41
I/O55
I/O83
30
40
50
241
Y24
I/O26
I/O42
I/O56
I/O84
31
41
51
240
AA25
GND
GND
GND(1)
VCC
VCC
VCC(1)
I/O57
I/O85
239
AB25
I/O58
I/O86
238
AA24
I/O87
I/O88
I/O27
I/O43
I/O59
I/O89
I/O28
I/O44
I/O60
I/O90
27
21
18
28
32
42
52
237
Y23
22
19
29
33
43
53
236
AC26
GND
I/O91
AD26
I/O92
AC25
I/O29
I/O45
I/O61
I/O93
30
34
44
54
235
AA23
I/O30
I/O46
I/O62
I/O94
31
35
45
55
234
AB24
I/O31
(OTS)(3)
I/O47
(OTS)(3)
I/O63
(OTS)(3)
I/O95
(OTS)(3)
28
23
20
32
36
46
56
233
AD25
I/O32,
GCK2
I/O48,
GCK2
I/O64,
GCK2
I/O96,
GCK2
29
24
21
33
37
47
57
232
AC24
M1
M1
M1
M1
30
25
22
34
38
48
58
231
AB23
GND
GND
GND
GND
31
26
23
35
39
49
59
230
GND(1)
M0
M0
M0
M0
32
27
24
36
40
50
60
229
AD24
Notes:
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
3. On-chip tri-state.
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
VCC
VCC
VCC
VCC
33
28
25
37
41
55
61
228
VCC(1)
M2
M2
M2
M2
34
29
26
38
42
56
62
227
AC23
I/O33,
GCK3
I/O49,
GCK3
I/O65,
GCK3
I/O97,
GCK3
35
30
27
39
43
57
63
226
AE24
I/O34
(HDC)
I/O50
(HDC)
I/O66
(HDC)
I/O98
(HDC)
36
31
28
40
44
58
64
225
AD23
I/O35
I/O51
I/O67
I/O99
41
45
59
65
224
AC22
I/O36
I/O52
I/O68
I/O100
42
46
60
66
223
AF24
I/O53
I/O69
I/O101
43
47
61
67
222
AD22
I/O37
Notes:
40
Bottom Side (Left to Right)
32
29
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O38
(LDC)
I/O54
(LDC)
I/O70
(LDC)
I/O102
(LDC)
Bottom Side (Left to Right)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
37
33
30
44
48
62
68
221
AE23
GND
I/O103
I/O104
I/O105
AC21
I/O106
AD21
I/O71
I/O107
220
AE22
I/O72
I/O108
219
AF23
VCC
VCC
VCC(1)
GND
GND
GND(1)
I/O39
I/O55
I/O73
I/O109
49
63
69
218
AD20
I/O40
I/O56
I/O74
I/O110
50
64
70
217
AE21
I/O57
I/O75
I/O111
65
71
216
AF21
I/O58
I/O76
I/O112
66
72
215
AC19
I/O113
I/O114
GND
I/O77
I/O115
I/O78
I/O116
I/O59
I/O79
I/O117
73
214
AD19
I/O60
I/O80
I/O118
74
213
AE20
I/O119
212
AF20
I/O120
211
AC18
GND
GND
GND
GND
45
51
67
75
210
GND(1)
I/O41
I/O61
I/O81
I/O121
46
52
68
76
209
AD18
I/O42
I/O62
I/O82
I/O122
47
53
69
77
208
AE19
I/O43
I/O63
I/O83
I/O123
38
34
31
48
54
70
78
207
AC17
I/O44
I/O64
I/O84
I/O124
39
35
32
49
55
71
79
206
AD17
VCC
VCC
VCC
80
204
VCC(1)
I/O65
I/O85
I/O125
72
81
203
AE18
I/O66
I/O86
I/O126
73
82
202
AF18
GND
I/O127
I/O128
Notes:
I/O129
AC16
I/O130
AD16
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
41
0896C–FPGA–04/02
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O87
I/O131
I/O88
I/O132
GND
GND
Bottom Side (Left to Right)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
201
AE17
200
VCC(1)
VCC
I/O89
AE16
GND(1)
83
I/O133
199
AF16
I/O90
I/O134
198
AC15
I/O67
I/O91
I/O135
84
197
AD15
I/O68
I/O92
I/O136
85
196
AE15
I/O45
I/O69
I/O93
I/O137
36
33
50
56
74
86
195
AF15
I/O46
I/O70
I/O94
I/O138
37
34
51
57
75
87
194
AD14
GND
I/O139
I/O140
I/O141
I/O142
I/O47
(D15)
I/O71
(D15)
I/O95
(D15)
I/O143
(D15)
40
38
35
52
58
76
88
193
AE14
I/O48
(INIT)
I/O72
(INIT)
I/O96
(INIT)
I/O144
(INIT)
41
39
36
53
59
77
89
192
AF14
VCC
VCC
VCC
VCC
42
40
37
54
60
78
90
191
VCC(1)
GND
GND
GND
GND
43
41
38
55
61
79
91
190
GND(1)
I/O49
(D14)
I/O73
(D14)
I/O97
(D14)
I/O145
(D14)
44
42
39
56
62
80
92
189
AE13
I/O50
(D13)
I/O74
(D13)
I/O98
(D13)
I/O146
(D13)
45
43
40
57
63
81
93
188
AC13
I/O147
I/O148
I/O149
I/O150
GND
I/O51
I/O75
I/O99
I/O151
44
41
58
64
82
94
187
AD13
I/O52
I/O76
I/O100
I/O152
45
42
59
65
83
95
186
AF12
I/O77
I/O101
I/O153
84
96
185
AE12
I/O78
I/O102
I/O154
85
97
184
AD12
I/O103
I/O155
183
AC12
I/O104
I/O156
182
AF11
VCC(1)
VCC
Notes:
42
GND
GND
I/O105
I/O157
GND(1)
98
181
AE11
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O106
I/O158
Bottom Side (Left to Right)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
180
AD11
I/O159
AE10
I/O160
AC11
I/O161
I/O162
GND
I/O79
I/O107
I/O163
99
179
AF9
I/O80
I/O108
I/O164
100
178
AD10
VCC
VCC
VCC
101
177
VCC(1)
I/O53
(D12)
I/O81
(D12)
I/O109
(D12)
I/O165
(D12)
46
46
43
60
66
86
102
175
AE9
I/O54
(D11)
I/O82
(D11)
I/O110
(D11)
I/O166
(D11)
47
47
44
61
67
87
103
174
AD9
I/O55
I/O83
I/O111
I/O167
62
68
88
104
173
AC10
I/O56
I/O84
I/O112
I/O168
63
69
89
105
172
AF7
GND
GND
GND
GND
64
70
90
106
171
GND(1)
I/O113
I/O169
170
AE8
I/O114
I/O170
169
AD8
I/O85
I/O115
I/O171
107
168
AC9
I/O86
I/O116
I/O172
108
167
AF6
I/O173
I/O174
GND
I/O175
I/O176
I/O87
I/O117
I/O177
91
109
166
AE7
I/O88
I/O118
I/O178
92
110
165
AD7
I/O57
I/O89
I/O119
I/O179
71
93
111
164
AE6
I/O58
I/O90
I/O120
I/O180
72
94
112
163
AE5
GND
GND
GND(1)
VCC
VCC
VCC(1)
I/O121
I/O181
162
AD6
I/O122
I/O182
161
AC7
I/O59
(D10)
I/O91
(D10)
I/O123
(D10)
I/O183
(D10)
48
48
45
65
73
95
113
160
AF4
I/O60
(D9)
I/O92
(D9)
I/O124
(D9)
I/O184
(D9)
49
49
46
66
74
96
114
159
AF3
Notes:
I/O185
AE4
I/O186
AC6
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
43
0896C–FPGA–04/02
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
Bottom Side (Left to Right)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
GND
I/O187
I/O188
I/O61
I/O93
I/O125
I/O189
67
75
97
115
158
AD5
I/O62
I/O94
I/O126
I/O190
68
76
98
116
157
AE3
I/O63
(D8)
I/O95
(D8)
I/O127
(D8)
I/O191
(D8)
50
50
47
69
77
99
117
156
AD4
I/O64,
GCK4
I/O96,
GCK4
I/O128,
GCK4
I/O192,
GCK4
51
51
48
70
78
100
118
155
AC5
GND
GND
GND
GND
52
52
49
71
79
101
119
154
GND(1)
CON
CON
CON
CON
53
53
50
72
80
103
120
153
AD3
Notes:
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
VCC
VCC
VCC
VCC
54
54
51
73
81
106
121
152
VCC(1)
RESET
RESET
RESET
RESET
55
55
52
74
82
108
122
151
AC4
I/O65
(D7)
I/O97
(D7)
I/O129
(D7)
I/O193
(D7)
56
56
53
75
83
109
123
150
AD2
I/O66,
GCK5
I/O98,
GCK5
I/O130,
GCK5
I/O194,
GCK5
57
57
54
76
84
110
124
149
AC3
I/O67
I/O99
I/O131
I/O195
77
85
111
125
148
AB4
I/O68
I/O100
I/O132
I/O196
78
86
112
126
147
AD1
I/O133
I/O197
AB3
I/O134
I/O198
AC2
Right Side (Bottom to Top)
GND
I/O101
I/O135
I/O199
127
146
AA4
I/O102
I/O136
I/O200
128
145
AA3
I/O203
144
AB2
I/O204
143
I/O201
I/O202
I/O69
(D6)
Notes:
44
I/O103
(D6)
AC1
VCC
VCC
VCC(1)
GND
GND
GND(1)
I/O137
(D6)
I/O205
(D6)
58
58
55
79
87
113
129
142
Y3
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O70
I/O104
I/O138
I/O206
I/O71
I/O105
I/O139
I/O72
I/O106
I/O140
Right Side (Bottom to Top)
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
59
56
80
88
114
130
141
AA2
I/O207
89
115
131
140
AA1
I/O208
90
116
132
139
W4
84
PLCC
I/O209
I/O210
GND
I/O211
I/O212
I/O107
I/O141
I/O213
117
133
138
W3
I/O108
I/O142
I/O214
118
134
137
Y2
I/O143
I/O215
136
Y1
I/O144
I/O216
135
V4
GND
GND
GND
135
134
GND(1)
I/O109
I/O145
I/O217
136
133
V3
I/O110
I/O146
I/O218
137
132
W2
I/O73,
FCK3
I/O111,
FCK3
I/O147,
FCK3
I/O219,
FCK3
82
92
120
138
131
U4
I/O74
I/O112
I/O148
I/O220
83
93
121
139
130
U3
VCC
VCC
VCC
140
129
VCC(1)
I/O75
(D5)
I/O113
(D5)
I/O149
(D5)
I/O221
(D5)
59
60
57
84
94
122
141
127
V2
I/O76
(CS0)
I/O114
(CS0)
I/O150
(CS0)
I/O222
(CS0)
60
61
58
85
95
123
142
126
V1
GND
81
91
119
GND
I/O223
T4
I/O224
T3
I/O225
I/O226
I/O151
I/O227
125
U2
I/O152
I/O228
124
T2
GND
GND
GND(1)
143
VCC(1)
VCC
I/O229
I/O230
Notes:
I/O153
I/O231
123
T1
I/O154
I/O232
122
R4
I/O115
I/O155
I/O233
124
144
121
R3
I/O116
I/O156
I/O234
125
145
120
R2
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
45
0896C–FPGA–04/02
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
Right Side (Bottom to Top)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
GND
I/O77
I/O117
I/O157
I/O235
62
59
86
96
126
146
119
R1
I/O78
I/O118
I/O158
I/O236
63
60
87
97
127
147
118
P3
I/O237
I/O238
I/O79(D4)
I/O119(D4)
I/O159(D4)
I/O239(D4)
61
64
61
88
98
128
148
117
P2
I/O80
I/O120
I/O160
I/O240
62
65
62
89
99
129
149
116
P1
VCC
VCC
VCC
VCC
63
66
63
90
100
130
150
115
VCC(1)
GND
GND
GND
GND
64
67
64
91
101
131
151
114
GND(1)
I/O81
(D3)
I/O121
(D3)
I/O161
(D3)
I/O241
(D3)
65
68
65
92
102
132
152
113
N2
66
69
66
93
103
133
153
112
N4
70
67
94
104
134
154
111
N3
95
105
135
155
110
M1
I/O82
I/O122
I/O162
I/O242
(CHECK)
(CHECK)
(CHECK)
(CHECK)
I/O243
I/O244
I/O83
I/O123
I/O163
I/O245
I/O84
I/O124
I/O164
I/O246
GND
I/O125
I/O165
I/O247
136
156
109
M2
I/O126
I/O166
I/O248
137
157
108
M3
I/O167
I/O249
107
M4
I/O168
I/O250
106
L1
I/O251
I/O252
VCC(1)
VCC
GND(1)
GND
GND
158
I/O169
I/O253
105
L2
I/O170
I/O254
104
L3
I/O255
K2
I/O256
L4
I/O257
I/O258
GND
I/O85
(D2)
I/O127
(D2)
I/O171
(D2)
I/O259
(D2)
67
71
68
96
106
138
159
103
I/O86
I/O128
I/O172
I/O260
68
72
69
97
107
139
160
102
K3
VCC
VCC
VCC
161
101
VCC(1)
I/O129
I/O173
I/O261
162
99
J2
I/O87
Notes:
46
98
108
140
J1
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O88,
FCK4
I/O130,
FCK4
I/O174,
FCK4
I/O262,
FCK4
I/O131
I/O175
I/O132
I/O176
GND
GND
GND
I/O177
I/O265
GND
Right Side (Bottom to Top)
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
99
109
141
163
98
J3
I/O263
164
97
K4
I/O264
165
96
G1
166
95
GND(1)
94
H2
84
PLCC
100
PQFP
100
TQFP
100
110
142
I/O178
I/O266
93
H3
I/O133
I/O179
I/O267
167
92
J4
I/O134
I/O180
I/O268
168
91
F1
I/O269
I/O270
GND
I/O135
I/O181
I/O271
143
169
90
G2
I/O136
I/O182
I/O272
144
170
89
G3
I/O89
I/O137
I/O183
I/O273
111
145
171
88
F2
I/O90
I/O138
I/O184
I/O274
112
146
172
87
E2
I/O275
I/O276
GND
GND
GND(1)
VCC
VCC
VCC(1)
I/O91
(D1)
I/O139
(D1)
I/O185
(D1)
I/O277
(D1)
69
73
70
101
113
147
173
86
F3
I/O92
I/O140
I/O186
I/O278
70
74
71
102
114
148
174
85
G4
I/O279
D1
I/O280
C1
I/O281
I/O282
GND
I/O187
I/O283
84
D2
I/O188
I/O284
83
F4
I/O93
I/O141
I/O189
I/O285
103
115
149
175
82
E3
I/O94
I/O142
I/O190
I/O286
104
116
150
176
81
C2
I/O95
(D0)
I/O143
(D0)
I/O191
(D0)
I/O287
(D0)
I/O96,
I/O144,
I/O192,
I/O288,
GCK6
GCK6
GCK6
GCK6
(CSOUT)
(CSOUT)
(CSOUT)
(CSOUT)
Notes:
71
75
72
105
117
151
177
80
D3
72
76
73
106
118
152
178
79
E4
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
47
0896C–FPGA–04/02
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
CCLK
CCLK
CCLK
CCLK
73
77
74
107
119
153
179
78
C3
VCC
VCC
VCC
VCC
74
78
75
108
120
154
180
77
VCC(1)
TSTCLK
TSTCLK
TSTCLK
TSTCLK
75
79
76
109
121
159
181
76
D4
Notes:
Right Side (Bottom to Top)
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
GND
GND
GND
GND
76
80
77
110
122
160
182
75
GND(1)
I/O97
(A0)
I/O145
(A0)
I/O193
(A0)
I/O289
(A0)
77
81
78
111
123
161
183
74
B3
I/O98,
GCK7
(A1)
I/O146,
GCK7
(A1)
I/O194,
GCK7
(A1)
I/O290,
GCK7
(A1)
78
82
79
112
124
162
184
73
C4
I/O99
I/O147
I/O195
I/O291
113
125
163
185
72
D5
I/O100
I/O148
I/O196
I/O292
114
126
164
186
71
A3
Top Side (Right to Left)
I/O293
I/O294
GND
I/O295
C5
I/O296
B4
I/O101
I/O149
I/O197
I/O297
(CS1,A2)
(CS1,A2)
(CS1,A2)
(CS1,A2)
I/O102
(A3)
I/O150
(A3)
I/O198
(A3)
I/O298
(A3)
I/O199
I/O103
(3)
I/O104
79
83
80
115
127
165
187
70
D6
80
84
81
116
128
166
188
69
C6
I/O299
68
B5
I/O200
I/O300
67
A4
VCC
VCC
VCC(1)
GND
GND
GND(1)
I/O151 (3)
I/O201 (3)
I/O301 (3)
I/O152
I/O202
I/O302
I/O153
I/O203
I/O303
I/O154
I/O204
I/O304
75(3)
NC
79(3)
NC
76(3)
NC
I/O305
109(3)
NC
117
121 (3)
NC
159 (3)
NC
189 (3)
NC
66 (3)
NC
C7 (3)
NC
190
65
B6
129
167
191
64
A6
130
168
192
63
D8
C8
I/O306
GND
Notes:
48
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
3. Shared with TSTCLK. No Connect.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
Top Side (Right to Left)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
I/O307
I/O308
I/O155
I/O205
I/O309
169
193
62
B7
I/O156
I/O206
I/O310
170
194
61
A7
I/O207
I/O311
195
60
D9
I/O208
I/O312
59
C9
GND
GND
GND
GND
118
131
171
196
58
GND(1)
I/O105
I/O157
I/O209
I/O313
119
132
172
197
57
B8
I/O106
I/O158
I/O210
I/O314
120
133
173
198
56
D10
I/O159
I/O211
I/O315
199
55
C10
I/O160
I/O212
I/O316
200
54
B9
VCC
VCC
VCC
201
52
VCC(1)
I/O213
I/O317
51
A9
I/O214
I/O318
50
D11
GND
I/O319
I/O320
I/O321
C11
I/O322
B10
I/O215
I/O323
49
B11
I/O216
I/O324
48
A11
GND
GND
GND(1)
VCC
VCC(1)
I/O107
(A4)
I/O161
(A4)
I/O217
(A4)
I/O325
(A4)
81
85
82
121
134
174
202
47
D12
I/O108
(A5)
I/O162
(A5)
I/O218
(A5)
I/O326
(A5)
82
86
83
122
135
175
203
46
C12
176
205
45
B12
136
177
206
44
A12
I/O163
I/O219
I/O327
I/O164
I/O220
I/O328
I/O109
I/O165
I/O221
I/O329
87
84
123
137
178
207
43
C13
I/O110
I/O166
I/O222
I/O330
88
85
124
138
179
208
42
B13
89
86
125
139
180
209
41
A13
GND
I/O331
I/O332
I/O333
I/O334
I/O111
(A6)
Notes:
I/O167
(A6)
I/O223
(A6)
I/O335
(A6)
83
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
3. Shared with TSTCLK. No Connect.
49
0896C–FPGA–04/02
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O112
(A7)
I/O168
(A7)
I/O224
(A7)
GND
GND
VCC
Top Side (Right to Left)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
I/O336
(A7)
84
90
87
126
140
181
210
40
B14
GND
GND
1
91
88
127
141
182
211
39
GND(1)
VCC
VCC
VCC
2
92
89
128
142
183
212
38
VCC(1)
I/O113
(A8)
I/O169
(A8)
I/O225
(A8)
I/O337
(A8)
3
93
90
129
143
184
213
37
D14
I/O114
(A9)
I/O170
(A9)
I/O226
(A9)
I/O338
(A9)
4
94
91
130
144
185
214
36
C14
I/O339
I/O340
I/O341
I/O342
GND
I/O115
I/O171
I/O227
I/O343
95
92
131
145
186
215
35
A15
I/O116
I/O172
I/O228
I/O344
96
93
132
146
187
216
34
B15
I/O173
I/O229
I/O345
188
217
33
C15
189
218
32
D15
I/O174
I/O230
I/O346
I/O117
(A10)
I/O175
(A10)
I/O231
(A10)
I/O347
(A10)
5
97
94
133
147
190
220
31
A16
I/O118
(A11)
I/O176
(A11)
I/O232
(A11)
I/O348
(A11)
6
98
95
134
148
191
221
30
B16
VCC
VCC(1)
GND
GND
GND(1)
I/O233
I/O349
29
C16
I/O234
I/O350
28
B17
I/O351
D16
I/O352
A18
I/O353
I/O354
GND
I/O355
27
C17
I/O236
I/O356
26
B18
VCC
VCC
VCC
222
25
VCC(1)
I/O177
I/O237
I/O357
223
23
C18
I/O178
I/O238
I/O358
224
22
D17
I/O119
I/O179
I/O239
I/O359
135
149
192
225
21
A20
I/O120
I/O180
I/O240
I/O360
136
150
193
226
20
B19
GND
GND
GND
GND
137
151
194
227
19
GND(1)
I/O241
I/O361
18
C19
Notes:
50
I/O235
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
3. Shared with TSTCLK. No Connect.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K05
AT40K05LV
AT40K10
AT40K10LV
AT40K20
AT40K20LV
AT40K40
AT40K40LV
128 I/O
192 I/O
256 I/O
384 I/O
I/O242
I/O362
I/O181
I/O243
I/O363
195
I/O182
I/O244
I/O364
196
Top Side (Right to Left)
84
PLCC
100
PQFP
100
TQFP
144
LQFP
160
PQFP
208
PQFP
240
PQFP
304
PQFP(2)
352
SBGA(2)
17
D18
228
16
A21
229
15
B20
I/O365
I/O366
GND
I/O367
I/O368
I/O121
I/O183
I/O245
I/O369
152
197
230
14
C20
I/O122
I/O184
I/O246
I/O370
153
198
231
13
B21
I/O123
(A12)
I/O185
(A12)
I/O247
(A12)
I/O371
(A12)
7
99
96
138
154
199
232
12
B22
I/O124
(A13)
I/O186
(A13)
I/O248
(A13)
I/O372
(A13)
8
100
97
139
155
200
233
10
C21
GND
GND
GND(1)
VCC
VCC
VCC(1)
I/O249
I/O373
9
D20
I/O250
I/O374
8
A23
I/O375
A24
I/O376
B23
I/O377
I/O378
GND
I/O187
I/O251
I/O379
234
7
D21
I/O188
I/O252
I/O380
235
6
C22
I/O125
I/O189
I/O253
I/O381
140
156
201
236
5
B24
I/O126
I/O190
I/O254
I/O382
141
157
202
237
4
C23
I/O127
(A14)
I/O191
(A14)
I/O255
(A14)
I/O383
(A14)
9
1
98
142
158
203
238
3
D22
I/O128,
GCK8
(A15)
I/O192,
GCK8
(A15)
I/O256,
GCK8
(A15)
I/O384,
GCK8
(A15)
10
2
99
143
159
204
239
2
C24
VCC
VCC
VCC
VCC
11
3
100
144
160
205
240
1
VCC(1)
Notes:
1. Pads labeled GND or VCC are internally bonded to Ground or VCC planes within the package. They have no direct connection to any specific package pin.
2. This package has an inverted die.
3. Shared with TSTCLK. No Connect.
51
0896C–FPGA–04/02
Power and Ground Pinouts for 352 SBGA(1)
VCC Pins
A10
A17
B2
B25
D7
D13
D19
G23
H4
K1
K26
N23
P4
U1
U26
W23
Y4
AC8
AC14
AC20
AE2
AE25
AF10
AF17
GND Pins
Note:
52
A1
A2
A5
A8
A14
A19
A22
A25
A26
B1
B26
E1
E26
H1
H26
N1
P26
W1
W26
AB1
AB26
AE1
AE26
AF1
AF2
AF5
AF8
AF13
AF19
AF22
AF25
AF26
1. In SBGA packages, Power and Ground pins do not connect directly to die. They connect to Power and Ground planes inside
the package.
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
Part/Package Availability and User I/O Counts (including Dual-function Pins)
Package(1)
AT40K05/AT40K05LV
AT40K10/AT40K10LV
AT40K20/AT40K20LV
AT40K40/AT40K40LV
84 PLCC
62
62
62
–
100 PQFP
78
78
77
–
100 TQFP
78
78
78
–
144 LQFP
114
114
114
114
160 PQFP
128
130
130
–
208 PQFP
128
161
161
161
240 PQFP
–
–
193
193
304 PQFP
–
–
–
256
352 SBGA
–
–
–
289
Note:
1. Devices in same package are pin-to-pin compatible.
Package Type
84J
84-lead, Plastic J-leaded Chip Carrier (PLCC)
100Q4
100-lead, Plastic Quad Flat Package (PQFP)
100T1
100-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
144L1
144-lead, Low-profile (1.4 mm) Plastic Quad Flat Package (LQFP)
160Q1
160-lead, Plastic Quad Flat Package (PQFP)
208Q1
208-lead, Plastic Quad Flat Package (PQFP)
240Q1
240-lead, Plastic Quad Flat Package (PQFP)
304Q1
304-lead, Plastic Quad Flat Package (PQFP)
352C1
252-ball, Enhanced, Low-profile Square Ball Grid Array Package (SBGA)
53
0896C–FPGA–04/02
AT40K05/AT40K05LV Ordering Information
Operating Voltage
Speed Grade (ns)
Ordering Code
Package
5,000 - 10,000
5.0V
2
AT40K05-2AJC
AT40K05-2AQC
AT40K05-2RQC
AT40K05-2BQC
AT40K05-2CQC
AT40K05-2DQC
84J
100T1
100Q4
144L1
160Q1
208Q1
Commercial
(0°C to 70°C)
5,000 - 10,000
5.0V
2
AT40K05-2AJI
AT40K05-2AQI
AT40K05-2RQI
AT40K05-2BQI
AT40K05-2CQI
AT40K05-2DQI
84J
100T1
100Q4
144L1
160Q1
208Q1
Industrial
(-40°C to 85°C)
5,000 - 10,000
3.3V
3
AT40K05LV-3AJC
AT40K05LV-3AQC
AT40K05LV-3RQC
AT40K05LV-3BQC
AT40K05LV-3CQC
AT40K05LV-3DQC
84J
100T1
100Q4
144L1
160Q1
208Q1
Commercial
(0°C to 70°C)
5,000 - 10,000
3.3V
3
AT40K05LV-3AJI
AT40K05LV-3AQI
AT40K05LV-3RQI
AT40K05LV-3BQI
AT40K05LV-3CQI
AT40K05LV-3DQI
84J
100T1
100Q4
144L1
160Q1
208Q1
Industrial
(-40°C to 85°C)
Note:
54
Operation Range(1)
Usable Gates
1. For military parts, contact Atmel at [email protected].
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K10/AT40K10LV Ordering Information
Operation Range(1)
Usable Gates
Operating Voltage
Speed Grade (ns)
Ordering Code
Package
10,000 - 20,000
5.0V
2
AT40K10-2AJC
AT40K10-2AQC
AT40K10-2RQC
AT40K10-2BQC
AT40K10-2CQC
AT40K10-2DQC
84J
100T1
100Q4
144L1
160Q1
208Q1
Commercial
(0°C to 70°C)
10,000 - 20,000
5.0V
2
AT40K10-2AJI
AT40K10-2AQI
AT40K10-2RQI
AT40K10-2BQI
AT40K10-2CQI
AT40K10-2DQI
84J
100T1
100Q4
144L1
160Q1
208Q1
Industrial
(-40°C to 85°C)
10,000 - 20,000
3.3V
3
AT40K10LV-3AJC
AT40K10LV-3AQC
AT40K10LV-3RQC
AT40K10LV-3BQC
AT40K10LV-3CQC
AT40K10LV-3DQC
84J
100T1
100Q4
144L1
160Q1
208Q1
Commercial
(0°C to 70°C)
10,000 - 20,000
3.3V
3
AT40K10LV-3AJI
AT40K10LV-3AQI
AT40K10LV-3RQI
AT40K10LV-3BQI
AT40K10LV-3CQI
AT40K10LV-3DQI
84J
100T1
100Q4
144L1
160Q1
208Q1
Industrial
(-40°C to 85°C)
Note:
1. For military parts, contact Atmel at [email protected].
55
0896C–FPGA–04/02
AT40K20/AT40K20LV Ordering Information
Operation Range(1)
Usable Gates
Operating Voltage
Speed Grade (ns)
Ordering Code
Package
20,000 - 30,000
5.0V
2
AT40K20-2AJC
AT40K20-2AQC
AT40K20-2RQC
AT40K20-2BQC
AT40K20-2CQC
AT40K20-2DQC
AT40K20-2EQC
84J
100T1
100Q4
144L1
160Q1
208Q1
240Q1
Commercial
(0°C to 70°C)
20,000 - 30,000
5.0V
2
AT40K20-2AJI
AT40K20-2AQI
AT40K20-2RQI
AT40K20-2BQI
AT40K20-2CQI
AT40K20-2DQI
AT40K20-2EQI
84J
100T1
100Q4
144L1
160Q1
208Q1
240Q1
Industrial
(-40°C to 85°C)
20,000 - 30,000
3.3V
3
AT40K20LV-3AJC
AT40K20LV-3AQC
AT40K20LV-3RQC
AT40K20LV-3BQC
AT40K20LV-3CQC
AT40K20LV-3DQC
AT40K20LV-2EQC
84J
100T1
100Q4
144L1
160Q1
208Q1
240Q1
Commercial
(0°C to 70°C)
20,000 - 30,000
3.3V
3
AT40K20LV-3AJI
AT40K20LV-3AQI
AT40K20LV-3RQI
AT40K20LV-3BQI
AT40K20LV-3CQI
AT40K20LV-3DQI
AT40K20LV-2EQI
84J
100T1
100Q4
144L1
160Q1
208Q1
240Q1
Industrial
(-40°C to 85°C)
Note:
56
1. For military parts, contact Atmel at [email protected]
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
AT40K40/AT40K40LV Ordering Information
Operation Range(1)
Usable Gates
Operating Voltage
Speed Grade (ns)
Ordering Code
Package
40,000 - 50,000
5.0V
2
AT40K40-2BQC
AT40K40-2DQC
AT40K40-2EQC
AT40K40-2FQC
AT40K40-2BGC
144Q1
208Q1
240Q1
304Q1
352C1
Commercial
(0°C to 70°C)
40,000 - 50,000
5.0V
2
AT40K40-2BQI
AT40K40-2DQI
AT40K40-2EQI
AT40K40-2FQI
AT40K40-2BGI
144Q1
208Q1
240Q1
304Q1
352C1
Industrial
(-40°C to 85°C)
40,000 - 50,000
3.3V
3
AT40K40LV-2BQC
AT40K40LV-2DQC
AT40K40LV-2EQC
AT40K40LV-2FQC
AT40K40LV-2BGC
144Q1
208Q1
240Q1
304Q1
352C1
Commercial
(0°C to 70°C)
40,000 - 50,000
3.3V
3
AT40K40LV-2BQI
AT40K40LV-2DQI
AT40K40LV-2EQI
AT40K40LV-2FQI
AT40K40LV-2BGI
144Q1
208Q1
240Q1
304Q1
352C1
Industrial
(-40°C to 85°C)
Note:
1. For military parts, contact Atmel at [email protected].
57
0896C–FPGA–04/02
Packaging Information
84J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
IDENTIFIER
E1
E
D2/E2
B1
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
COMMON DIMENSIONS
(Unit of Measure = mm)
45˚ MAX (3X)
Notes:
1. This package conforms to JEDEC reference MS-018, Variation AF.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
4.191
–
4.572
A1
2.286
–
3.048
A2
0.508
–
–
D
30.099
–
30.353
D1
29.210
–
29.413
E
30.099
–
30.353
E1
29.210
–
29.413
D2/E2
27.686
–
28.702
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
58
2325 Orchard Parkway
San Jose, CA 95131
TITLE
84J, 84-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
84J
B
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
100T1 – TQFP
D
D1
XX
e
E
b
UN T
RY
CO
E1
Bottom View
Top View
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
A2
MIN
A1
0.05
A2
0.95
D
A1
L1
Side View
NOM
0.15
1.00
6
16.00 BSC
14.00 BSC
E
16.00 BSC
E1
14.00 BSC
e
0.50 BSC
L1
NOTE
1.05
D1
b
MAX
0.17
0.22
2, 3
2, 3
0.27
4, 5
1.00 REF
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances,
datums, etc.
2. The top package body size may be smaller than the bottom package size by as much as 0.15 mm.
3. Dimensions D1 and E1 do not include mold protrusions. Allowable protrusion is 0.25 mm per side. D1 and E1 are maximum plastic
body size dimensions, including mold mismatch.
4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall not cause the lead width to exceed the maximum
b dimension by more than 0.08 mm. Dambar cannot be located on the lower radius or the foot. Minimum space between protrusion and
an adjacent lead is 0.07 mm for 0.4 and 0.5 mm pitch packages.
5. These dimensions apply to the flat section of the lead between 0.10 mm and 0.25 mm from the lead tip.
6. A1 is defined as the distance from the seating place to the lowest point on the package body.
11/30/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
100T1, 100-lead (14 x 14 x 1.0 mm Body), Thin Plastic
Quad Flat Pack (TQFP)
DRAWING NO.
100T1
REV.
A
59
0896C–FPGA–04/02
100Q4 – PQFP
D1
D
E
E1
Top View
Bottom View
A2
A1
e
b
L1
COMMON DIMENSIONS
(Unit of Measure = mm)
Side View
SYMBOL
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing
MS-022, Variation GC-1, for additional information.
2. To be determined at seating plane.
3. Regardless of the relative size of the upper and lower body sections,
dimensions D1 and E1 are determined at the largest feature of the body
exclusive of mold Flash and gate burrs, but including any mismatch
between the upper and lower sections of the molded body.
4. Dimension b does not include Dambar protrusion. The Dambar
protrusion(s) shall not cause the lead width to exceed b maximum by more
than 0.08 mm. Dambar cannot be located on the lower radius or the lead
foot.
5. A1 is defined as the distance from the seating plane to the lowest
point of the package body.
MIN
A1
0.25
A2
2.50
D
MAX
NOTE
–
0.50
5
2.70
2.90
NOM
23.20 BSC
2
D1
20.00 BSC
3
E
17.20 BSC
2
E1
14.00 BSC
3
e
b
0.65 BSC
0.22
L1
0.40
4
1.60 REF
3/29/02
R
60
2325 Orchard Parkway
San Jose, CA 95131
TITLE
100Q4, 100-lead, 14 x 20 mm Body, 3.2 Form Opt.,
Plastic Quad Flat Pack (PQFP)
DRAWING NO.
100Q4
REV.
A
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
144L1 – LQFP
D1
D
XX
e
E1
b
UN T
RY
CO
E
Bottom View
Top View
COMMON DIMENSIONS
(Unit of Measure = mm)
A2
SYMBOL
MIN
A1
0.05
A2
1.35
D
A1
L1
Side View
NOM
0.15
1.40
20.00 BSC
E
22.00 BSC
E1
20.00 BSC
e
0.50 BSC
L1
NOTE
6
1.45
22.00 BSC
D1
b
MAX
0.17
0.22
2, 3
2, 3
0.27
4, 5
1.00 REF
Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-026 for additional information.
2. The top package body size may be smaller than the bottom package size by as much as 0.15 mm.
3. Dimensions D1 and E1 do not include mold protrusions. Allowable protrusion is 0.25 mm per side. D1 and E1 are maximum plastic
body size dimensions including mold mismatch.
4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall not cause the lead width to exceed the maximum
b dimension by more than 0.08 mm. Dambar cannot be located on the lower radius or the foot. Minimum space between protrusion and
an adjacent lead is 0.07 mm for 0.4 and 0.5 mm pitch packages.
5. These dimensions apply to the flat section of the lead between 0.10 mm and 0.25 mm from the lead tip.
6. A1 is defined as the distance from the seating place to the lowest point on the package body.
11/30/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
144L1, 144-lead (20 x 20 x 1.4 mm Body), Low Profile
Plastic Quad Flat Pack (LQFP)
DRAWING NO.
144L1
REV.
A
61
0896C–FPGA–04/02
160Q1 – PQFP
D1
D
E
E1
Top View
Bottom View
A2
A1
e
b
COMMON DIMENSIONS
(Unit of Measure = mm)
L1
SYMBOL
Side View
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing
MS-022, Variation DD-1, for additional information.
2. To be determined at seating plane.
3. Regardless of the relative size of the upper and lower body sections,
dimensions D1 and E1 are determined at the largest feature of the body
exclusive of mold Flash and gate burrs, but including any mismatch
between the upper and lower sections of the molded body.
4. Dimension b does not include Dambar protrusion. The Dambar
protrusion(s) shall not cause the lead width to exceed b maximum by more
than 0.08 mm. Dambar cannot be located on the lower radius or the lead
foot.
5. A1 is defined as the distance from the seating plane to the lowest point of
the package body.
MIN
NOM
MAX
A1
0.25
–
0.50
A2
3.20
3.40
3.60
D
31.20 BSC
NOTE
5
2
D1
28.00 BSC
3
E
31.20 BSC
2
E1
28.00 BSC
3
e
0.65 BSC
b
0.22
L1
–
0.40
4
1.60 REF
3/28/02
R
62
2325 Orchard Parkway
San Jose, CA 95131
TITLE
160Q1, 160-lead, 28 x 28 mm Body, 3.2 Form Opt.,
Plastic Quad Flat Pack (PQFP)
DRAWING NO.
160Q1
REV.
A
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
208Q1 – TQFP
D1
A2
L1
A1
Side View
E1
e
b
Top View
D
COMMON DIMENSIONS
(Unit of Measure = mm)
E
SYMBOL
MIN
A1
0.25
A2
3.20
D
MAX
NOM
3.40
3.60
30.60 BSC
D1
28.00 BSC
E
30.60 BSC
E1
28.00 BSC
e
b
NOTE
0.50
2, 3
2, 3
0.50 BSC
0.17
L1
0.27
4
1.30 REF
Bottom View
Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc.
2. The top package body size may be smaller than the bottom package size by as much as 0.15 mm.
3. Dimensions D1 and E1 do not include mold protrusions. Allowable protrusion is 0.25 mm per side. D1 and E1 are maximum plastic
body size dimensions including mold mismatch.
4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall not cause the lead width to exceed the maximum b
dimension by more than 0.08 mm. Dambar cannot be located on the lower radius or the foot. Minimum space between protrusion
and an adjacent lead is 0.07 mm.
11/30/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
208Q1, 208-lead (28 x 28 mm Body, 2.6 Form Opt.),
Plastic Quad Flat Pack (PQFP)
DRAWING NO.
208Q1
REV.
A
63
0896C–FPGA–04/02
240Q1 – PQFP
D1
D
E1
E
Top View
Bottom View
A2
A1
e
b
L1
COMMON DIMENSIONS
(Unit of Measure = mm)
Side View
SYMBOL
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing
MS-029, Variation GA, for additional information.
2. All dimensioning and tolerancing conforms to ASME Y14.5M-1994.
3. To be determined at seating plane.
4. Dimensions D1 and E1 do not include mold protrusions. Allowable
protrusion is 0.25 mm per side. D1 and E1 are maximum plastic body size
dimensions including mold mismatch. Dimensions D1 and E1 shall be
determined at datum plane.
5. Dimension b does not include Dambar protrusion. Allowable Dambar
protrusion shall not cause the lead width to exceed the maximum b
dimension by more than 0.08 mm. Dambar cannot be located on the lower
radius or the foot. The minimum space between protrusion and an adjacent
lead shall not be less than 0.07 mm.
MIN
NOM
MAX
A1
0.25
–
0.50
A2
3.20
3.40
3.60
D
NOTE
34.60 BSC
3
D1
32.00 BSC
2, 4
E
34.60 BSC
3
E1
32.00 BSC
2, 4
e
b
0.50 BSC
0.17
L1
–
0.27
5
1.30 REF
3/29/02
R
64
2325 Orchard Parkway
San Jose, CA 95131
TITLE
240Q1, 240-lead, 32 x 32 mm Body, 2.6 Form Opt.,
Plastic Quad Flat Pack (PQFP)
DRAWING NO.
240Q1
REV.
A
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
AT40K/AT40KLV Series FPGA
304Q1 – PQFP
D
D1
E1
E
Bottom View
Top View
A2
A1
e
b
L1
Side View
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing
MS-029, Variation JA, for additional information.
2. All dimensioning and tolerancing conforms to ASME Y14.5M-1994.
3. To be determined at seating plane.
4. Dimensions D1 and E1 do not include mold protrusions. Allowable
protrusion is 0.25 mm per side. D1 and E1 are maximum plastic body size
dimensions including mold mismatch. Dimensions D1 and E1 shall be
determined at Datum plane.
5. Dimension b does not include Dambar protrusion. Allowable Dambar
protrusion shall not cause the lead width to exceed the maximum b
dimension by more than 0.08 mm. Dambar can not be located on the lower
radius or the foot. The minimum space between protrusion and an adjacent
lead shall not be less than 0.07 mm.
MIN
NOM
MAX
A1
0.25
–
0.50
A2
3.55
3.80
4.05
NOTE
D
42.60 BSC
3
D1
40.00 BSC
2, 4
E
42.60 BSC
3
E1
40.00 BSC
2, 4
e
b
0.50 BSC
0.17
L1
–
0.27
5
1.30 REF
3/29/02
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
304Q1, 304-lead, 40 x 40 mm Body, 2.6 Form Opt.,
Plastic Quad Flat Pack (PQFP)
DRAWING NO.
304Q1
REV.
A
65
0896C–FPGA–04/02
352C1 – SBGA
A1 BALL CORNER
A1 BALL
CORNER
D
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
b∅
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
A1 BALL I.D.
E
e
e
Top View
Bottom View
Die Side
A
A2
A1
SEATING PLANE
Section View
Side View
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing
MO-192, Variation BAR-2, for additional information.
2. JEDEC variations are based on fully populated ball arrays. Arrays
can be depopulated as desired by removing balls from the fully populated
array.
MIN
NOM
D
35.0 BSC
E
35.0 BSC
Matrix Size
26 x 26
MAX
A
–
–
1.70
A1
0.35
–
–
A2
0.25
–
1.10
b∅
0.60
0.75
0.90
e
NOTE
1.27 BSC
3/29/02
R
66
2325 Orchard Parkway
San Jose, CA 95131
TITLE
352C1, 352-ball, 35 x 35, Enhanced, Low-profile
Square Ball Grid Array Package (SBGA)
DRAWING NO.
REV.
352C1
A
AT40K/AT40KLV Series FPGA
0896C–FPGA–04/02
Atmel Headquarters
Atmel Operations
Corporate Headquarters
Memory
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 487-2600
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
TEL (41) 26-426-5555
FAX (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimhatsui
East Kowloon
Hong Kong
TEL (852) 2721-9778
FAX (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
TEL (81) 3-3523-3551
FAX (81) 3-3523-7581
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
TEL (49) 71-31-67-0
FAX (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
TEL (33) 2-40-18-18-18
FAX (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL 1(719) 576-3300
FAX 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
TEL (33) 4-76-58-30-00
FAX (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
TEL (33) 4-42-53-60-00
FAX (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL 1(719) 576-3300
FAX 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
TEL (44) 1355-803-000
FAX (44) 1355-242-743
Atmel Programmable SLI Hotline
e-mail
(408) 436-4119
[email protected]
Atmel Programmable SLI e-mail
Web Site
[email protected]
http://www.atmel.com
FAQ
Available on web site
© Atmel Corporation 2002.
Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty
which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors
which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does
not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted
by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical
components in life support devices or systems.
ATMEL ® and Cache Logic ® are the registered trademarks of Atmel. FreeRAM ™ and QuickChange are the
trademarks of Atmel.
Concept®, Verilog ® and OrCAD ® are the registered trademarks of Cadence Design Systems, Inc.; Mentor ® and
Veribest® are the registered trademarks of Mentor Graphics; Exemplar ™ is the trademark of Mentor Graphics;
Synario™ is the trademark of Data I/O Corporation; Synopsys ® is the registered trademark of Synopsis, Inc.;
Viewlogic ™ is the trademark of Viewlogic Systems, Inc.; Synplicity® is the registered trademark of Synplify, Inc.
Other terms and product names may be the trademarks of others.
Printed on recycled paper.
0896C–FPGA–04/02
xM