I2C-bus controlled 4 x 45 Watt power amplifier and multiple voltage regulato ...

INTEGRATED CIRCUITS
DATA SHEET
TDA8589J; TDA8589xJ
I2C-bus controlled 4 × 45 Watt
power amplifier and multiple
voltage regulator
Product specification
2004 Feb 24
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
FEATURES
Amplifiers
• I2C-bus control
• Can drive a 2 Ω load with a battery voltage of up to 16 V
and a 4 Ω load with a battery voltage of up to 18 V
• DC load detection: open, short and present
PROTECTION
• AC load (tweeter) detection
• If connection to the battery voltage is reversed, all
regulator voltages will be zero
• Programmable clip detect 1 % or 3%
• Programmable thermal protection pre-warning
• Independent short-circuit protection per channel
• Able to withstand voltages at the output of up to 18 V
(supply line may be short-circuited)
• Low gain line driver mode (20 dB)
• Thermal protection to avoid thermal breakdown
• Loss-of-ground and open VP safe
• Load-dump protection
• All outputs protected from short-circuit to ground, to VP,
or across the load
• Regulator outputs protected from DC short-circuit to
ground or to supply voltage
• All pins protected from short-circuit to ground
• All regulators protected by foldback current limiting
• Soft thermal-clipping to prevent audio holes
• Power switches protected from loss-of-ground.
• Low battery detection.
APPLICATIONS
Voltage regulators
• Boost amplifier and voltage regulator for car radios and
CD/MD players.
GENERAL
• I2C-bus control
• Good stability with almost any output capacitor value
GENERAL DESCRIPTION
• Five voltage regulators (microcontroller, display,
mechanical digital, mechanical drive and audio)
Amplifiers
The TDA8589 has a complementary quad audio power
amplifier that uses BCDMOS technology. It contains four
amplifiers configured in Bridge Tied Load (BTL) to drive
speakers for front and rear left and right channels. The
I2C-bus allows diagnostic information of each amplifier and
its speaker to be read separately. Both front and both rear
channel amplifiers can be configured independently in line
driver mode with a gain of 20 dB (differential output).
• Choice of non-adjustable 3.3 or 5 V microcontroller
supply (REG2) versions reducing risk of overvoltage
damage
• Choice of non-adjustable 3.3 or 5 V digital signal
processor supply (REG3) versions reducing risk of
overvoltage damage
• Selectable output voltages for regulators 1, 4 and 5
• Low dropout voltage PNP output stages
Voltage regulators
• High supply voltage ripple rejection
• Low noise for all regulators
The TDA8589 has a multiple output voltage regulator with
two power switches.
• Two power switches (antenna switch and amplifier
switch)
The voltage regulator contains the following:
• Four switchable regulators and one permanently active
regulator (microcontroller supply)
• Regulator 2 (microcontroller supply) operational during
load-dump and thermal shut-down
• Two power switches with loss-of-ground protection
• Low quiescent current (only regulator 2 is operational)
• A reset output that can be used to communicate with a
microcontroller.
• Reset output (push-pull output stage)
• Adjustable reset delay time
The quiescent current has a very low level of 150 µA with
only regulator 2 active.
• Backup functionality.
2004 Feb 24
2
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
QUICK REFERENCE DATA
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX. UNIT
Amplifiers
VP1, VP2
operating supply voltage
Iq(tot)
total quiescent current
Po(max)
maximum output power
8
−
14.4
18
V
270
400
mA
RL = 4 Ω; VP = 14.4 V; VIN = 2 V 39
RMS square wave
41
−
W
RL = 4 Ω; VP = 15.2 V; VIN = 2 V 44
RMS square wave
46
−
W
RL = 2 Ω; VP = 14.4 V; VIN = 2 V 64
RMS square wave
69
−
W
THD
total harmonic distortion
−
0.01
0.1
%
Vn(o)(amp)
noise output voltage in amplifier mode
−
50
70
µV
Vn(o)(LN)
noise output voltage in line driver mode
−
25
35
µV
regulator 1, 3, 4 and 5 on
10
14.4
18
V
regulator 2 on
4
−
−
V
Voltage regulators
SUPPLY
VP
Iq(tot)
supply voltage
total quiescent supply current
jump starts for t ≤ 10 minutes
−
−
30
V
load dump protection for
t ≤ 50 ms and tr ≤ 2.5 ms
−
−
50
V
overvoltage for shut-down
20
−
−
V
standby mode; VP = 14.4 V
−
150
190
µA
IB2[D3:D2] = 01
−
8.3
−
V
IB2[D3:D2] = 10
−
8.5
−
V
IB2[D3:D2] = 11
−
8.7
−
V
TDA8589J; TDA8589AJ
−
5.0
−
V
TDA8589BJ
−
3.3
−
V
TDA8589J
−
5.0
−
V
TDA8589AJ; TDA8589BJ
−
3.3
−
V
VOLTAGE REGULATORS
VO(REG1)
VO(REG2)
VO(REG3)
VO(REG4)
2004 Feb 24
output voltage of regulator 1
output voltage of regulator 2
output voltage of regulator 3
output voltage of regulator 4
0.5 mA ≤ IO ≤ 400 mA;
selectable via I2C-bus
0.5 mA ≤ IO ≤ 350 mA
0.5 mA ≤ IO ≤ 300 mA
maximum current ≥ 1.6 A;
0.5 mA ≤ IO ≤ 800 mA;
selectable via I2C-bus
V
IB2[D7:D5] = 001
−
5.0
−
V
IB2[D7:D5] = 010
−
6.0
−
V
IB2[D7:D5] = 011
−
7.0
−
V
IB2[D7:D5] = 100
−
8.6
−
V
3
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
SYMBOL
VO(REG5)
PARAMETER
output voltage of regulator 5
TDA8589J; TDA8589xJ
CONDITIONS
MIN.
TYP.
MAX. UNIT
0.5 mA ≤ IO ≤ 400 mA;
selectable via I2C-bus
IB1[D7:D4] = 0001
−
6.0
−
V
IB1[D7:D4] = 0010
−
7.0
−
V
IB1[D7:D4] = 0011
−
8.2
−
V
IB1[D7:D4] = 0100
−
9.0
−
V
IB1[D7:D4] = 0101
−
9.5
−
V
IB1[D7:D4] = 0110
−
10.0
−
V
IB1[D7:D4] = 0111
−
10.4
−
V
IB1[D7:D4] = 1000
−
12.5
−
V
IB1[D7:D4] = 1001
−
VP −
1
−
V
POWER SWITCHES
Vdrop(SW1)
dropout voltage of switch 1
IO = 400 mA
−
0.6
1.1
V
Vdrop(SW2)
dropout voltage of switch 2
IO = 400 mA
−
0.6
1.1
V
ORDERING INFORMATION
OUTPUT VOLTAGE(1)
PACKAGE
TYPE NUMBER
NAME
TDA8589J
TDA8589AJ
DBS37P
DESCRIPTION
VERSION
REGULATOR 2
REGULATOR 3
plastic DIL-bent-SIL power package;
37 leads (lead length 6.8 mm)
SOT725-1
5V
5V
TDA8589BJ
5V
3.3 V
3.3 V
3.3 V
Note
1. Permanent output voltage of regulator 2 and output voltage of regulator 3, respectively.
2004 Feb 24
4
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
BLOCK DIAGRAM
BUCAP
36
35
TDA8589
ENABLE
LOGIC
REGULATOR 1
30
REGULATOR 3
31
REGULATOR 4
33
REGULATOR 5
34
Vreg2
SWITCH 1
29
SWITCH 2
27
40 µs
RESCAP
SCL
STB
IN1
REG1
REG3
REG4
REG5
SW1
SW2
28
26
32
SDA
REG2
TEMPERATURE &
LOAD DUMP
PROTECTION VOLTAGE
REGULATOR
REFERENCE
VOLTAGE
BACKUP
SWITCH
VP
37
REGULATOR 2
20
2
6
4
25
22
STANDBY/ MUTE
11
I2C-BUS
INTERFACE
GND
VP1
VP2
DIAG
CLIP DETECT/ DIAGNOSTIC
9
MUTE
RST
26 dB/
20 dB
7
OUT1+
OUT1−
PROTECTION/
DIAGNOSTIC
IN2
15
17
MUTE
26 dB/
20 dB
19
OUT2+
OUT2−
PROTECTION/
DIAGNOSTIC
IN3
12
5
MUTE
26 dB/
20 dB
3
OUT3+
OUT3−
PROTECTION/
DIAGNOSTIC
IN4
14
21
MUTE
26 dB/
20 dB
VP
23
OUT4+
OUT4−
PROTECTION/
DIAGNOSTIC
TEMPERATURE & LOAD
DUMP PROTECTION
AMPLIFIER
10
SVR
13
16
SGND
ACGND
8
1
5
24
PGND1
PGND3
PGND4
PGND2/TAB
Fig.1 Block diagram.
2004 Feb 24
18
mdb538
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
PINNING
SYMBOL
PIN
DESCRIPTION
PGND2/TAB
1
power ground 2 and connection for heatsink
SDA
2
I2C-bus data input and output
OUT3−
3
channel 3 negative output
SCL
4
I2C-bus clock input
OUT3+
5
channel 3 positive output
VP2
6
power supply voltage 2 to amplifier
OUT1−
7
channel 1 negative output
PGND1
8
power ground 1
OUT1+
9
channel 1 positive output
SVR
10
half supply voltage filter capacitor
IN1
11
channel 1 input
IN3
12
channel 3 input
SGND
13
signal ground
IN4
14
channel 4 input
IN2
15
channel 2 input
ACGND
16
AC ground
OUT2+
17
channel 2 positive output
PGND3
18
power ground 3
OUT2−
19
channel 2 negative output
VP1
20
power supply voltage 1 to amplifier
OUT4+
21
channel 4 positive output
STB
22
standby or operating or mute mode select input
OUT4−
23
channel 4 negative output
PGND4
24
power ground 4
DIAG
25
diagnostic and clip detection output; active LOW
RST
26
reset output
SW2
27
antenna switch; supplies unregulated power to car aerial motor
RESCAP
28
reset delay capacitor
SW1
29
amplifier switch; supplies unregulated power to amplifier(s)
REG1
30
regulator 1 output; supply for audio part of radio and CD player
REG3
31
regulator 3 output; supply for signal processor part (mechanical digital) of CD player
GND
32
combined voltage regulator, power and signal ground
REG4
33
regulator 4 output; supply for mechanical part (mechanical drive) of CD player
REG5
34
regulator 5 output; supply for display part of radio and CD player
VP
35
power supply to voltage regulator
BUCAP
36
connection for backup capacitor
REG2
37
regulator 2 output; supply voltage to microcontroller
2004 Feb 24
6
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
PGND2/TAB 1
SDA 2
OUT3− 3
SCL 4
OUT3+ 5
VP2 6
OUT1− 7
PGND1 8
OUT1+ 9
SVR 10
IN1 11
IN3 12
SGND 13
IN4 14
IN2 15
ACGND 16
OUT2+ 17
PGND3 18
OUT2− 19
TDA8589
VP1 20
OUT4+ 21
STB 22
OUT4− 23
PGND4 24
DIAG 25
RST 26
SW2 27
RESCAP 28
SW1 29
REG1 30
REG3 31
GND 32
REG4 33
REG5 34
VP 35
BUCAP 36
REG2 37
001aaa259
Fig.2 Pin configuration.
2004 Feb 24
7
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
Power-on reset and supply voltage spikes (see Fig.13
and (see Fig.14))
FUNCTIONAL DESCRIPTION
The TDA8589 is a multiple voltage regulator combined
with four independent audio power amplifiers configured in
bridge tied load with diagnostic capability. The output
voltages of all regulators except regulators 2 and 3 can be
controlled via the I2C-bus. However, regulator 3 can be set
to 0 V via the I2C-bus. The output voltage of regulator 2
(microcontroller supply) and the maximum output voltage
of regulator 3 (mechanical digital and microcontroller
supplies) can both be either 5 V or 3.3 V depending on the
type number. The maximum output voltages of both
regulators are fixed to avoid any risk of damaging the
microcontroller that may occur during a disturbance of the
I2C-bus.
If the supply voltage drops too low to guarantee the
integrity of the data in the I2C-bus latches, the power-on
reset cycle will start. All latches will be set to a pre-defined
state, pin DIAG will be pulled LOW to indicate that a
power-on reset has occurred, and bit D7 of data byte 2 is
also set for the same reason. When D0 of instruction
byte 1 is set, the power-on flag resets, pin DIAG is
released and the amplifier will then enter its start-up cycle.
Diagnostic output
Pin DIAG indicates clipping, thermal protection
pre-warning of amplifier and voltage regulator sections,
short-circuit protection, low and high battery voltage.
Pin DIAG is an open-drain output, is active LOW, and must
be connected to an external voltage via an external pull-up
resistor. If a failure occurs, pin DIAG remains LOW during
the failure and no clipping information is available. The
microcontroller can read the failure information via the
I2C-bus.
The amplifier diagnostic functions give information about
output offset, load, or short-circuit. Diagnostic functions
are controlled via the I2C-bus. The TDA8589 is protected
against short-circuit, over-temperature, open ground and
open VP connections. If a short-circuit occurs at the input
or output of a single amplifier, that channel shuts down,
and the other channels continue to operate normally. The
channel that has a short-circuit can be disabled by the
microcontroller via the appropriate enable bit of the
I2C-bus to prevent any noise generated by the fault
condition from being heard.
AMPLIFIERS
Muting
A hard mute and a soft mute can both be performed via the
I2C-bus. A hard mute mutes the amplifier within 0.5 ms.
A soft mute mutes the amplifier within 20 ms and is less
audible. A hard mute is also activated if a voltage of 8 V is
applied to pin STB.
Start-up
At power on, regulator 2 will reach its final voltage when
the backup capacitor voltage exceeds 5.5 V independently
of the voltage on pin STB. When pin STB is LOW, the total
quiescent current is low, and the I2C-bus lines are high
impedance.
Temperature protection
When pin STB is HIGH, the I2C-bus is biased on and then
the TDA8589 performs a power-on reset. When bit D0 of
instruction byte IB1 is set, the amplifier is activated, bit D7
of data byte 2 (power-on reset occurred) is reset, and
pin DIAG is no longer held LOW.
If the average junction temperature rises to a temperature
value that has been set via the I2C-bus, a thermal
protection pre-warning is activated making pin DIAG LOW.
If the temperature continues to rise, all four channels will
be muted to reduce the output power (soft thermal
clipping). The value at which the temperature mute control
activates is fixed; only the temperature at which the
thermal protection pre-warning signal occurs can be
specified by bit D4 in instruction byte 3. If implementing
the temperature mute control does not reduce the average
junction temperature, all the power stages will be switched
off (muted) at the absolute maximum temperature Tj(max).
Start-up and shut-down timing (see Fig.12)
A capacitor connected to pin SVR enables smooth start-up
and shut-down, preventing the amplifier from producing
audible clicks at switch-on or switch-off. The start-up and
shut-down times can be extended by increasing the
capacitor value.
If the amplifier is shut down using pin STB, the amplifier is
muted, the regulators and switches are switched off, and
the capacitor connected to pin SVR discharges. The low
current standby mode is activated 2 seconds after pin STB
goes LOW.
2004 Feb 24
TDA8589J; TDA8589xJ
Offset detection
Offset detection can only be performed when there is no
input signal to the amplifiers, for instance when the
external digital signal processor is muted after a start-up.
The output voltage of each channel is measured and
8
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
AC-LOAD DETECTION
compared with a reference voltage. If the output voltage of
a channel is greater than the reference voltage, bit D2 of
the associated data byte is set and read by the
microcontroller during a read instruction. Note that the
value of this bit is only meaningful when there is no input
signal and the amplifier is not muted. Offset detection is
always enabled.
AC-load detection can be used to detect that AC-coupled
speakers are connected correctly during assembly. This
requires at least 3 periods of a 19 kHz sine wave to be
applied to the amplifier inputs. The amplifier produces a
peak output voltage which also generates a peak output
current through the AC-coupled speaker. The 19 kHz sine
wave is also audible during the test. If the amplifier detects
three current peaks that are greater than 550 mA, the
AC-load detection bit D1 of instruction byte IB1 is set to
logic 1. Three current peaks are counted to avoid false
AC-load detection which can occur if the input signal is
switched on and off. The peak current counter can be reset
by setting bit D1 of instruction byte IB1 to logic 0.
To guarantee AC-load detection, an amplifier current of
more than 550 mA is required. AC-load detection will
never occur with a current of less than 150 mA. Figure 3
shows which AC loads are detected at different output
voltages. For example, if a load is detected at an output
voltage of 2.5 V peak, the load is less than 4 Ω. If no load
is detected, the output impedance is more than 14 Ω.
Speaker protection
If one side of a speaker is connected to ground, a missing
current protection is implemented to prevent damage to
the speaker. A fault condition is detected in a channel
when there is a mismatch between the power current in the
high side and the power current in the low side; during a
fault condition the channel will be switched off.
The load status of each channel can be read via the
I2C-bus: short to ground (one side of the speaker
connected to ground), short to VP (one side of the speaker
connected to VP), and shorted load.
Line driver mode
An amplifier can be used as a line driver by switching it to
low gain mode. In normal mode, the gain between
single-ended input and differential output (across the load)
is 26 dB. In low gain mode the gain between single-ended
input and differential output is 20 dB.
The negative inputs to all four amplifier channels are
combined at pin ACGND. To obtain the best performance
for supply voltage ripple rejection and unwanted audible
noise, the value of the capacitor connected to pin ACGND
must be as close as possible to 4 times the value of the
input capacitor connected to the positive input of each
channel.
(1)
no load present
Zo(load)
(Ω)
Input and AC ground capacitor values
undefined
(2)
10
load present
Load detection
1
0
DC-LOAD DETECTION
When DC-load detection is enabled, during the start-up
cycle, a DC-offset is applied slowly to the amplifier outputs,
and the output currents are measured. If the output current
of an amplifier rises above a certain level, it is assumed
that there is a load of less than 6 Ω and bit D5 is reset in
the associated data byte register to indicate that a load is
detected.
2.5
5
7.5
10
Vo(peak) (V)
(1) IO(peak) = < 150 mA.
(2) IO(peak) = > 550 mA.
Fig.3
Because the offset is measured during the amplifier
start-up cycle, detection is inaudible and can be performed
every time the amplifier is switched on.
2004 Feb 24
mrc331
102
Tolerance of AC-load detection as a
function of output voltage.
LOAD DETECTION PROCEDURE
1. At start-up, enable the AC- or DC-load detection by
setting D1 of instruction byte 1 to logic 1.
9
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
2. After 250 ms the DC load is detected and the mute is
released. This is inaudible and can be implemented
each time the IC is powered on.
TDA8589J; TDA8589xJ
The headroom voltage is the voltage required for correct
operation of the amplifier and is defined as the voltage
difference between the level of the DC output voltage
before the VP voltage drop and the level of VP after the
voltage drop (see Fig.4).
3. When the amplifier start-up cycle is completed (after
1.5 s), apply an AC signal to the input, and DC-load
bits D5 of each data byte should be read and stored by
the microcontroller.
At a certain supply voltage drop, the headroom voltage will
be insufficient for correct operation of the amplifier.
To prevent unwanted audible noises at the output, the
headroom protection mode will be activated (see Fig.13).
This protection discharges the capacitors connected to
pins SVR and ACGND to increase the headroom voltage.
4. After at least 3 periods of the input signal, the load
status can be checked by reading AC-detect bits D4 of
each data byte.
The AC-load peak current counter can be reset by
setting bit D1 of instruction byte IB1 to logic 0 and then
to logic 1. Note that this will also reset the DC-load
detection bits D5 in each data byte.
Low headroom protection
The normal DC output voltage of the amplifier is set to half
the supply voltage and is related to the voltage on
pin SVR. An external capacitor is connected to pin SVR to
suppress power supply ripple. If the supply voltage drops
(at vehicle engine start), the DC output voltage will follow
slowly due to the affect of the SVR capacitor.
V
(V)
14
VP
vehicle engine start
headroom voltage
SVR voltage
8.4
7
amplifier
DC output voltage
t (sec)
mdb515
Fig.4 Amplifier output during supply voltage.
2004 Feb 24
10
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
VOLTAGE REGULATORS
Backup function
The voltage regulator section contains:
The backup function is implemented by a switch function,
which behaves like an ideal diode between pins VP
and BUCAP; the forward voltage of this ideal diode
depends on the current flowing through it. The backup
function supplies regulator 2 during brief periods when no
supply voltage is present on pin VP. It requires an external
capacitor to be connected to pin BUCAP and ground.
When the supply voltage is present on pin VP this
capacitor will be charged to a level of VP − 0.3 V. When the
supply voltage is absent from pin VP, this charge can then
be used to supply regulator 2 for a brief period (tbackup)
calculated using the formula:
• Four switchable regulators and one permanent active
regulator
• Two power switches with loss-of-ground protection
• Reset push-pull output
• Backup functionality.
The quiescent current condition has a very low current
level of 150 µA typical with only regulator 2 active. The
TDA8589 uses low dropout voltage regulators for use in
low voltage applications.
All of the voltage regulators except for the standby
regulator can be controlled via the I2C-bus. The voltage
regulator section of this device has two power switches
which are capable of delivering unregulated 400 mA
continuous current, and has several fail-safe protection
modes. It conforms to peak transient tests and protects
against continuous high voltage (24 V), short-circuits and
thermal stress. A reset warning signal is asserted if
regulator 2 is out of regulation. Regulator 2 will try to
maintain output for as long as possible even if a thermal
shut-down or any other fault condition occurs. During
overvoltage stress conditions, all outputs except
regulator 2 will switch off and the device will be able to
supply a minimum current for an indefinite amount of time
sufficient for powering the memory of a microcontroller.
Provision is made for an external reserve supply capacitor
to be connected to pin BUCAP which can store enough
energy to allow regulator 2 to supply a microcontroller for
a period long enough for it to prepare for a loss-of-voltage.
V P – ( V O ( REG2 ) – 0.5 )
t backup = C backup × R L ×  ---------------------------------------------------------


V O ( REG2 )
Example: VP = 14.4 V, VO(REG2) = 5 V, RL = 1 kΩ and
Cbackup = 100 µF provides a tbackup of 177 ms.
When an overvoltage condition occurs, the voltage on
pin BUCAP is limited to approximately 24 V; see Fig.5.
Regulator 2
Regulator 2 is intended to supply the microcontroller and
has a low quiescent current. This supply cannot be shut
down in response to overvoltage stress conditions, and is
not I2C-bus controllable to prevent the microcontroller from
being damaged by overvoltage which could occur during a
disturbance of the I2C-bus. This supply will not shut down
during load dump transients or during a high
thermal-protection condition.
Backup capacitor
The backup capacitor is used as a backup supply for the
regulator 2 output when the battery supply voltage (VP)
cannot support the regulator 2 voltage.
2004 Feb 24
11
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
V
(V)
TDA8589J; TDA8589xJ
VP
VBUCAP
VO(REG2)
t (sec)
tbackup
out of regulation
mdb512
V P – V O ( REG2 ) – 0.5
t backup = C backup ×  ----------------------------------------------------


IL
Fig.5 Backup capacitor function.
Reset output
Power switches
A reset pulse is generated at pin RST when the output
voltage of regulator 2 rises above the reset threshold
value. The reset output is a push-pull output that both
sources and sinks current. The output voltage can switch
between ground and VO(REG2), and operates at a low
regulator 2 voltage or VBUCAP. The RST signal is controlled
by a low-voltage detection circuit which, when activated,
pulls pin RST LOW (reset active) when VO(REG2) is
≤ Vth(rst). If VO(REG2) ≥ Vth(rst), pin RST goes HIGH. The
reset pulse is delayed by 40 µs internally. To extend the
delay and to prevent oscillations occurring at the threshold
voltage, an external capacitor can be connected to
pin RESCAP. Note that a reset pulse is not generated
when VO(REG2) falls below the reset threshold value.
There are two power switches that provide an unregulated
DC voltage output for amplifiers and an aerial motor
respectively. The switches have internal protection for
over-temperature conditions and are activated by setting
bits D2 and D3 of instruction byte IB1 to logic 1. The
regulated outputs will supply pulsed current loads that can
contaminate the line with high frequency noise, so it is
important to prevent any cross-coupling between the
regulated outputs, particularly with the 8.3 V audio supply,
and the unregulated outputs.
In the ON state, the switches have a low impedance to the
battery voltage. When the battery voltage is higher than
22 V, the switches are switched off. When the battery
voltage is below 22 V the switches are set to their original
condition.
Reset delay capacitor
A Reset Delay Capacitor (RDC) connected to
pin RESCAP can be used to extend the delay period of the
reset pulse and to ensure that a clean reset signal is sent
to the microcontroller. The RDC is charged by a current
source. The reset output (pin RST) will be released
(pin RST goes HIGH) when the RDC voltage crosses the
RDC threshold value.
2004 Feb 24
12
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
Protection
Temperature protection
All regulator and switch outputs are fully protected by
foldback current limiting against load dumps and
short-circuits; see Fig.6. During a load dump all regulator
outputs, except the output of regulator 2, will go low.
If the junction temperature of a regulator becomes too
high, the amplifier(s) are switched off to prevent unwanted
noise signals being audible. A regulator junction
temperature that is too high is indicated by pin DIAG going
LOW and is also indicated by setting bit D6 in data byte 2.
The power switches can withstand ‘loss-of-ground’. This
means that if pin GND becomes disconnected, the switch
is protected by automatically connecting its outputs to
ground.
handbook, full pagewidth
If the junction temperature of the regulator continues to
rise and reaches the maximum temperature protection
level, all regulators and switches will be disabled except
regulator 2.
VO(REGn)
Isc
Ilimit
IO(REGn)
MDB513
Fig.6 Foldback current protection.
2004 Feb 24
13
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
I2C-BUS SPECIFICATION
0 = write
1 = read
handbook, halfpage
MSB
1
LSB
1
0
1
1
0
0
R/W
MDB516
Fig.7 Address byte.
If address byte bit R/W = 0, the TDA8589 expects 3 instruction bytes: IB1, IB2 and IB3; see Table 1 to Table 6.
After a power-on, all instruction bits are set to zero.
If address byte bit R/W = 1, the TDA8589 will send 4 data bytes to the microcontroller: DB1, DB2, DB3 and DB4; see
Table 7 to Table 10.
SDA
SDA
SCL
SCL
S
P
START condition
STOP condition
Fig.8 Definition of start and stop conditions.
SDA
SCL
data line
stable;
data valid
change
of data
allowed
Fig.9 Bit transfer.
2004 Feb 24
14
MBA607
MBA608
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
I2C-WRITE
SCL
1
SDA
MSB
2
MSB − 1
S
7
8
LSB + 1
ADDRESS
9
ACK
1
MSB
A
W
2
7
MSB − 1
LSB + 1
8
LSB
WRITE DATA
9
ACK
A
P
To stop the transfer, after the last acknowledge (A)
a stop condition (P) must be generated
I2C-READ
SCL
1
SDA
MSB
2
MSB − 1
S
7
8
LSB + 1
ADDRESS
9
ACK
R
A
1
MSB
2
7
MSB − 1
LSB + 1
READ DATA
8
LSB
9
ACK
A
P
To stop the transfer, the last byte must not be acknowledged
and a stop condition (P) must be generated
: generated by master (microcontroller)
: generated by slave (TDA8589)
S
: start
P
: stop
A
: acknowledge
R/W
mdb517
: read / write
Fig.10 I2C-bus read and write modes.
2004 Feb 24
15
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
Table 1
Instruction byte IB1
BIT
D7
D6
TDA8589J; TDA8589xJ
Table 3
BIT
DESCRIPTION
D7
regulator 5 output voltage control
(see Table 2)
D6
D5
D5
D4
D4
D3
Instruction byte IB2
DESCRIPTION
regulator 4 output voltage control (see
Table 4)
regulator 3 (mechanical digital) control
0 = regulator 3 off
SW2 control
1 = regulator 3 on
0 = SW2 off
D3
1 = SW2 on
D2
D2
SW1 control
D1
0 = SW1 off
1 = SW1 on
D1
regulator 1 output voltage control (see
Table 5)
soft mute all amplifier channels (mute delay
20 ms)
0 = mute off
AC- or DC-load detection switch
1 = mute on
0 = AC- or DC-load detection off; resets
DC-load detection bits and AC-load
detection peak current counter
D0
hard mute all amplifier channels (mute delay
0.4 ms)
0 = mute off
1 = AC- or DC-load detection on
D0
1 = mute on
amplifier start enable (clear power-on reset
flag; D7 of DB2)
Table 4
0 = amplifier OFF; pin DIAG remains LOW
1 = amplifier ON; when power-on occurs,
bit D7 of DB2 is reset and pin DIAG is
released
Table 2
BIT
OUTPUT (V)
Regulator 5 (display) output voltage control
BIT
OUTPUT (V)
D7
D6
D5
D4
0
0
0
0
0 (off)
0
0
0
1
6.0
0
0
1
0
7.0
0
0
1
1
8.2
0
1
0
0
9.0
0
1
0
1
9.5
0
1
1
0
10.0
0
1
1
1
10.4
1
0
0
0
12.5
1
0
0
1
≤ VP − 1
(switch)
2004 Feb 24
Regulator 4 (mechanical drive) output voltage
control
D7
D6
D5
0
0
0
0 (off)
0
0
1
5
0
1
0
6
0
1
1
7
1
0
0
8.6
Table 5
Regulator 1 (audio) output voltage control
BIT
OUTPUT (V)
16
D3
D2
0
0
0 (off)
0
1
8.3
1
0
8.5
1
1
8.7
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
Table 6
Instruction byte IB3
BIT
D7
D6
TDA8589J; TDA8589xJ
Table 7
BIT
DESCRIPTION
D7
clip detection level
1 = 1 % detection level
1 = junction temperature above pre-warning
level
amplifier channels 1 and 2 gain select
D6
1 = junction temperature above 175 °C
amplifier channels 3 and 4 gain select
D5
1 = no DC load detected
amplifier thermal protection pre-warning
D4
0 = warning at 145 °C
1 = AC load detected
disable channel 1
D3
0 = enable channel 1
channel 4 load short-circuit
0 = normal load
1 = disable channel 1
1 = short-circuit load
disable channel 2
D2
0 = enable channel 2
channel 4 output offset
0 = no output offset
1 = disable channel 2
1 = output offset
disable channel 3
D1
0 = enable channel 3
channel 4 VP short-circuit
0 = no short-circuit to VP
1 = disable channel 3
D0
channel 4 AC load detection
0 = no AC load detected
1 = warning at 122 °C
D1
channel 4 DC load detection
0 = DC load detected
1 = 20 dB gain (line driver mode)
D2
amplifier maximum thermal protection
0 = junction temperature below 175 °C
0 = 26 dB gain (normal mode)
D3
amplifier thermal protection pre-warning
0 = no warning
1 = 20 dB gain (line driver mode)
D4
DESCRIPTION
0 = 3 % detection level
0 = 26 dB gain (normal mode)
D5
Data byte DB1
1 = short-circuit to VP
disable channel 4
D0
0 = enable channel 4
channel 4 ground short-circuit
0 = no short-circuit to ground
1 = disable channel 4
1 = short-circuit to ground
2004 Feb 24
17
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
Table 8
Data byte DB2
BIT
D7
D6
TDA8589J; TDA8589xJ
Table 9
BIT
DESCRIPTION
−
0 = amplifier on
D6
−
1 = POR has occurred; amplifier off
D5
channel 2 DC load detection
0 = DC load detected
regulator thermal protection pre-warning
1 = no DC load detected
D4
1 = regulator temperature too high; amplifier
off
1 = AC load detected
D3
1 = no DC load detected
1 = short-circuit load
D2
1 = AC load detected
1 = output offset
D1
1 = short-circuit load
1 = short-circuit to VP
D0
1 = output offset
1 = short-circuit to ground
1 = short-circuit to VP
channel 3 ground short-circuit
0 = no short-circuit to ground
1 = short-circuit to ground
2004 Feb 24
channel 2 ground short-circuit
0 = no short-circuit to ground
channel 3 VP short-circuit
0 = no short-circuit to VP
D0
channel 2 VP short-circuit
0 = no short-circuit to VP
channel 3 output offset
0 = no output offset
D1
channel 2 output offset
0 = no output offset
channel 3 load short-circuit
0 = normal load
D2
channel 2 load short-circuit
0 = normal load
channel 3 AC load detection
0 = no AC load detected
D3
channel 2 AC load detection
0 = no AC load detected
channel 3 DC load detection
0 = DC load detected
D4
DESCRIPTION
D7
Power-on reset occurred or amplifier status
0 = no warning
D5
Data byte DB3
18
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
Table 10 Data byte DB4
BIT
DESCRIPTION
D7
−
D6
−
D5
channel 1 DC load detection
0 = DC load detected
1 = no DC load detected
D4
channel 1 AC load detection
0 = no AC load detected
1 = AC load detected
D3
channel 1 load short-circuit
0 = normal load
1 = short-circuit load
D2
channel 1 output offset
0 = no output offset
1 = output offset
D1
channel 1 VP short-circuit
0 = no short-circuit to VP
1 = short-circuit to VP
D0
channel 1 ground short-circuit
0 = no short-circuit to ground
1 = short-circuit to ground
2004 Feb 24
19
TDA8589J; TDA8589xJ
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134).
SYMBOL
VP
PARAMETER
supply voltage
CONDITION
MIN.
MAX.
UNIT
operating
−
18
V
not operating
−1
+50
V
with load dump protection
0
50
V
VSDA, VSCL voltage on pins SDA and SCL
operating
0
7
V
VIN, VSVR,
VACGND,
VDIAG
voltage on pins INn, SVR,
ACGND and DIAG
operating
0
13
V
operating
VSTB
voltage on pin STB
0
24
V
IOSM
non-repetitive peak output
current
−
10
A
IORM
repetitive peak output current
−
6
A
Vsc
AC and DC short-circuit voltage short-circuit of output pins across
loads and to ground or supply
−
18
V
Vrp
reverse polarity voltage
voltage regulator only
−
−18
V
Ptot
total power dissipation
Tcase = 70 °C
−
80
W
Tj
junction temperature
−
150
°C
Tstg
storage temperature
−55
+150
°C
Tamb
ambient temperature
−40
+85
°C
Vesd
electrostatic discharge voltage
note 1
−
2000
V
note 2
−
200
V
Notes
1. Human body model: Rs = 1.5 kΩ; C = 100 pF; all pins have passed all tests to 2500 V to guarantee 2000 V,
according to class II.
2. Machine model: Rs = 10 Ω; C = 200 pF; L = 0.75 mH; all pins have passed all tests to 250 V to guarantee 200 V,
according to class II.
2004 Feb 24
20
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
CONDITIONS
VALUE
UNIT
Rth(j-a)
thermal resistance from junction to ambient
in free air
40
K/W
Rth(j-c)
thermal resistance from junction to case
see Fig.11
0.75
K/W
Virtual junction
handbook, halfpage
Amplifier
Voltage regulator
0.5 K/W
1 K/W
0.2 K/W
Case
MDB514
Fig.11 Equivalent thermal resistance network.
QUALITY SPECIFICATION
In accordance with “General Quality Specification for Integrated Circuits SNW-FQ-611D”.
2004 Feb 24
21
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
CHARACTERISTICS
Amplifier section
Tamb = 25 °C; VP = 14.4 V; RL = 4 Ω; measured in the test circuit Fig.28; unless otherwise specified.
SYMBOL
PARAMETER
CONDITION
MIN.
TYP.
MAX.
UNIT
Supply voltage behaviour
VP1, VP2
operating supply voltage
RL = 4 Ω
8
14.4
18
V
RL = 2Ω
8
14.4
16
V
no load
−
280
400
mA
Iq(tot)
total quiescent current
Istb
standby current
−
10
50
µA
VO
DC output voltage
−
7.2
−
V
VP(mute)
low supply voltage mute
6.5
7
8
V
Vhr
headroom voltage
when headroom protection is
activated; see Fig.3
−
1.4
−
V
VPOR
power-on reset voltage
see Fig.13
−
5.5
−
V
VOO
output offset voltage
mute mode and power on
−100
0
+100
mV
Mode select (pin STB)
Vstb
standby mode voltage
−
−
1.3
V
Voper
operating mode voltage
2.5
−
5.5
V
Vmute
mute mode voltage
II
input current
8
−
VP
V
VSTB = 5 V
−
4
25
µA
Start-up, shut-down and mute timing
twake
wake-up time from standby
before first I2C-bus transmission
is recognised
via pin STB; see Fig.12
−
300
500
µs
tmute(off)
time from amplifier switch-on to
mute release
via I2C-bus (IB1 bit D0);
CSVR = 22 µF; see Fig.12
−
250
−
ms
td(mute-on)
delay from mute to on
soft mute; via I2C-bus
(IB2 bit D1 = 1 to 0)
10
25
40
ms
hard mute; via I2C-bus
(IB2 bit D0 = 1 to 0)
10
25
40
ms
via pin STB; VSTB = 4 to 8 V
10
25
40
ms
soft mute; via
(IB2 bit D1 = 0 to 1)
10
25
40
ms
hard mute; via I2C-bus
(IB2 bit D0 = 0 to 1)
−
0.4
1
ms
via pin STB; VSTB = 4 to 8 V
−
0.4
1
ms
td(on-mute)
delay from on to mute
I2C-bus
I2C-bus interface
VIL
LOW-level input voltage on pins
SCL and SDA
−
−
1.5
V
VIH
HIGH-level input voltage on pins
SCL and SDA
2.3
−
5.5
V
VOL
LOW-level output voltage on
pin SDA
−
−
0.4
V
2004 Feb 24
IL = 3 mA
22
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
SYMBOL
fSCL
PARAMETER
TDA8589J; TDA8589xJ
CONDITION
SCL clock frequency
MIN.
TYP.
MAX.
UNIT
−
400
−
kHz
−
−
0.8
V
± 1.5
±2
± 2.5
V
Diagnostic
VDIAG
diagnostic pin LOW output
voltage
Vo(offset)
output voltage when offset is
detected
THDclip
THD clip detection level
fault condition; IDIAG = 200 µA
IB3 bit D7 = 0
−
3
−
%
IB3 bit D7 = 1
−
1
−
%
135
145
155
°C
Tj(warn)
average junction temperature for
pre-warning
IB3 bit D4 = 0
IB3 bit D4 = 1
112
122
132
°C
Tj(mute)
average junction temperature for
3 dB muting
VIN = 0.05 V
150
160
170
°C
Tj(off)
average junction temperature
when all outputs are switched off
165
175
185
°C
Zo(load)
impedance when a DC load is
detected
−
−
6
Ω
Zo(open)
impedance when an open DC
load is detected
500
−
−
Ω
Io(load)
amplifier current when AC load
detection is detected
550
−
−
mA
Io(open)
amplifier current when an open
AC load is detected
−
−
150
mA
Amplifier
Po
THD
2004 Feb 24
output power
total harmonic distortion
RL = 4 Ω; VP = 14.4 V; THD = 0.5 % 18
19
−
W
RL = 4 Ω; VP = 14.4 V; THD = 10 %
25
26
−
W
RL = 4 Ω; VP = 14.4 V;
VIN = 2 V RMS square wave
(maximum power)
39
41
−
W
RL = 4 Ω; VP = 15.2 V;
VIN = 2 V RMS square wave
(maximum power)
44
46
−
W
RL = 2 Ω; VP = 14.4 V; THD = 0.5 % 27
31
−
W
RL = 2 Ω; VP = 14.4 V; THD = 10 %
40
44
−
W
RL = 2 Ω; VP = 14.4 V;
VIN = 2 V RMS square wave
(maximum power)
64
69
−
W
Po = 1 W to 12 W; f = 1 kHz;
RL = 4 Ω
−
0.01
0.1
%
Po = 1 W to 12 W; f = 10 kHz
−
0.2
0.5
%
Po = 4 W; f = 1 kHz
−
0.01
0.03
%
line driver mode; Vo = 2 V (RMS);
f = 1 kHz; RL = 600 Ω
−
0.01
0.03
%
23
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
SYMBOL
PARAMETER
TDA8589J; TDA8589xJ
CONDITION
MIN.
TYP.
MAX.
UNIT
f = 1 Hz to 10 kHz; Rsource = 600 Ω
50
60
−
dB
αcs
channel separation (crosstalk)
Po = 4 W; f = 1 kHz
−
80
−
dB
SVRR
supply voltage ripple rejection
f = 100 Hz to 10 kHz;
Rsource = 600 Ω
55
70
−
dB
CMRR
common mode ripple rejection
amplifier mode;
Vcommon = 0.3 V (p-p);
f = 1 kHz to 3 kHz; Rsource = 0 Ω
40
70
−
dB
Vcm(max)(rms)
maximum common mode voltage
level (rms value)
f = 1 kHz
−
−
0.6
V
Vn(o)(LN)
noise output voltage in line driver
mode
filter 20 Hz to 22 kHz;
Rsource = 600 Ω
−
25
35
µV
Vn(o)(amp)
noise output voltage in amplifier
mode
filter 20 Hz to 22 kHz;
Rsource = 600 Ω
−
50
70
µV
Gv(amp)
voltage gain in amplifier mode
single-ended in to differential out
25
26
27
dB
Gv(LN)
voltage gain in line driver mode
single-ended in to differential out
19
20
21
dB
Zi
input impedance
CIN = 220 nF
55
70
−
kΩ
αmute
mute attenuation
VO(on)/VO(mute)
80
90
−
dB
Vo(mute)
output voltage mute
VIN = 1 V (RMS)
−
70
−
µV
Bp
power bandwidth
−1 dB; THD = 1 %
−
20
−
kHz
Voltage regulator section
Tamb = 25 °C; VP = 14.4 V; measured in the test circuit Fig.28; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supply
VP
supply voltage
regulator 1, 3, 4 and 5 on
10.0
14.4
18
V
regulator 2
Iq(tot)
total quiescent supply
current
switched on
4
−
−
V
in regulation
6.3
−
50
V
overvoltage for shut-down
18.1
22
−
V
standby mode; note 1
−
150
190
µA
Reset output (push-pull stage, pin RST)
VREG2(th)(r)
rising threshold voltage
of regulator 2
VP is rising;
IO(REG2) = 50 mA
VO(REG2)
− 0.2
VO(REG2)
− 0.1
VO(REG2)
− 0.04
V
VREG2(th)(f)
falling threshold voltage
of regulator 2
VP is falling;
IO(REG2) = 50 mA
VO(REG2)
− 0.25
VO(REG2)
− 0.15
VO(REG2)
− 0.1
V
Isink(L)
LOW-level sink current
VRST ≤ 0.8 V
1
−
−
mA
Isource(H)
HIGH-level source
current
VRST = VO(REG2) − 0.5 V;
VP = 14.4 V
200
600
−
µA
tr
rise time
note 2
−
2
50
µs
tf
fall time
note 2
−
10
50
µs
2004 Feb 24
24
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
SYMBOL
PARAMETER
TDA8589J; TDA8589xJ
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Reset delay (pin RESCAP)
Ich
charge current
VRESCAP = 0 V
1
4
8
µA
Idch
discharge current
VRESCAP = 3 V; VP ≥ 4.3 V
1
7
−
mA
Vth(rst)
reset signal threshold
voltage
TDA8588AJ and
TDA8588J
2.5
3
3.5
V
td(rst)
reset signal delay
TDA8588BJ
1.6
2.1
2.6
V
without CRESCAP; note 3
−
40
−
µs
CRESCAP = 47 nF; note 3;
see Fig.15
15
35
100
ms
IB2[D3:D2] = 01
7.9
8.3
8.7
V
IB2[D3:D2] = 10
8.1
8.5
8.9
V
IB2[D3:D2] = 11
8.3
8.7
9.1
V
−
−
50
mV
Regulator 1: REG1 (audio; IO = 5 mA)
VO(REG1)
VO(LN)
output voltage
line regulation voltage
0.5 mA ≤ IO ≤ 400 mA;
12 V < VP < 18 V
12 V ≤ VP ≤ 18 V
VO(load)
load regulation voltage
5 mA ≤ IO ≤ 400 mA
−
−
100
mV
SVRR
supply voltage ripple
rejection
fripple = 120 Hz;
Vripple = 2 V (p-p)
50
60
−
dB
Vdrop
dropout voltage
VP = 7.5 V; note 4
IO = 200 mA
−
0.4
0.8
V
IO = 400 mA4
−
0.6
2.5
V
Ilimit
current limit
VO ≥ 7 V; note 5
400
700
−
mA
Isc
short-circuit current
RL ≤ 0.5 Ω; note 6
70
190
−
mA
TDA8589AJ and
TDA8589J
4.75
5.0
5.25
V
TDA8589BJ
3.1
3.3
3.5
V
−
3
50
mV
Regulator 2: REG2 (microprocessor; IO = 5 mA)
VO(REG2)
VO(LN)
output voltage
line regulation voltage
0.5 mA ≤ IO ≤ 350 mA;
10 V ≤ VP ≤ 18 V
10 V ≤ VP ≤ 18 V
VO(load)
load regulation voltage
0.5 mA ≤ IO ≤ 300 mA
−
−
100
mV
SVRR
supply voltage ripple
rejection
fripple = 120 Hz;
Vripple = 2 V (p-p)
40
50
−
dB
2004 Feb 24
25
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
SYMBOL
Vdrop
PARAMETER
dropout voltage
TDA8589J; TDA8589xJ
CONDITIONS
MIN.
TYP.
MAX.
UNIT
IO = 200 mA
VBUCAP = 4.75 V; note 7
TDA8589AJ and
TDA8589J
−
0.5
0.8
V
TDA8589BJ
−
1.75
2
V
TDA8589AJ and
TDA8589J
−
0.5
1.3
V
TDA8589BJ
−
1.75
2.7
V
IO = 350 mA;
VBUCAP = 4.75 V; note 7
Ilimit
current limit
VO ≥ 2.8 V; note 5
400
1000
−
mA
Isc
short-circuit current
RL ≤ 0.5 Ω; note 6
160
300
−
mA
TDA8589AJ and
TDA8589BJ
3.1
3.3
3.5
V
TDA8589J
4.75
5.0
5.25
V
−
3
50
mV
Regulator 3: REG3 (mechanical digital; IO = 5 mA)
VO(REG3)
VO(LN)
output voltage
line regulation voltage
0.5 mA ≤ IO ≤ 300 mA;
10 V ≤ VP ≤ 18 V
10 V ≤ VP ≤ 18 V
VO(load)
load regulation voltage
0.5 mA ≤ IO ≤ 300 mA
−
−
100
mV
SVRR
supply voltage ripple
rejection
fripple = 120 Hz;
Vripple = 2 V (p-p)
50
65
−
dB
Vdrop
dropout voltage
VP = 4.75 V; IO = 200 mA;
note 4
TDA8589AJ and
TDA8589BJ
−
1.45
1.65
V
TDA8589J
−
0.4
0.8
V
TDA8589AJ and
TDA8589BJ
−
1.45
1.65
V
TDA8589J
−
0.4
1.5
V
VP = 4.75 V; IO = 300 mA;
note 4
Ilimit
current limit
VO ≥ 2.8 V; note 5
400
700
−
mA
Isc
short-circuit current
RL ≤ 0.5 Ω; note 6
135
210
−
mA
IB2[D7:D5] = 001
4.75
5.0
5.25
V
IB2[D7:D5] = 010
5.7
6.0
6.3
V
IB2[D7:D5] = 011
6.6
7.0
7.4
V
Regulator 4: REG4 (mechanical drive; IO = 5 mA)
VO(REG4)
output voltage
0.5 mA ≤ IO ≤ 800 mA;
10 V ≤ VP ≤ 18 V
IB2[D7:D5] = 100
VO(LN)
2004 Feb 24
line regulation voltage
10 V ≤ VP ≤ 18 V
26
8.1
8.6
9.1
V
−
3
50
mV
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
SYMBOL
PARAMETER
TDA8589J; TDA8589xJ
CONDITIONS
MIN.
TYP.
MAX.
UNIT
VO(load)
load regulation voltage
0.5 mA ≤ IO ≤ 400 mA
−
−
100
mV
SVRR
supply voltage ripple
rejection
fripple = 120 Hz;
Vripple = 2 V (p-p)
50
65
−
dB
Vdrop
dropout voltage
VP = VO(REG4) − 0.5 V;
IO = 800 mA; note 4
−
0.6
1
V
IO(peak)
peak output current
t ≤ 3 s; VO = 4 V
1
1.5
−
A
Ilimit
current limit
VO ≥ 4 V; t ≤ 100 ms;
VP ≥ 11.5 V; note 5
1.5
2
−
A
Isc
short-circuit current
RL ≤ 0.5 Ω ; note 6
240
400
−
mA
10 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 0001
5.7
6.0
6.3
V
10 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 0010
6.65
7.0
7.37
V
10 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 0011
7.8
8.2
8.6
V
10.5 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 0100
8.55
9.0
9.45
V
11 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 0101
9.0
9.5
10.0
V
11.5 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 0110
9.5
10.0
10.5
V
13 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 0111
9.9
10.4
10.9
V
14.2 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 1000
11.8
12.5
13.2
V
12.5 V ≤ VP ≤ 18 V;
IB1[D7:D4] = 1001
VP − 1
−
−
V
Regulator 5: REG5 (display; IO = 5 mA)
VO(REG5)
output voltage
0.5 mA ≤ IO ≤ 400 mA;
VO(LN)
line regulation voltage
10 V ≤ VP ≤ 18 V
−
3
50
mV
VO(load)
load regulation voltage
0.5 mA ≤ IO ≤ 400 mA
−
−
100
mV
SVRR
supply voltage ripple
rejection
fripple = 120 Hz;
Vripple = 2 V (p-p)
50
60
−
dB
Vdrop
dropout voltage
VP = VO(REG5) − 0.5 V;
note 4
IO = 300 mA
−
0.4
0.8
V
IO = 400 mA
−
0.5
2.3
V
Ilimit
current limit
VO ≥ 5.5 V; note 5
400
950
−
mA
Isc
short-circuit current
RL ≤ 0.5 Ω; note 6
100
200
−
mA
IO = 300 mA
−
0.6
0.8
V
IO = 400 mA
−
0.6
1.1
V
V ≥ 8.5 V
0.5
1
−
A
Power switch 1: SW1 (antenna)
Vdrop(SW1)
dropout voltage
Ilimit
current limit
2004 Feb 24
27
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
SYMBOL
PARAMETER
TDA8589J; TDA8589xJ
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Power switch 2: SW2 (amplifier)
Vdrop(SW2)
Ilimit
dropout voltage
current limit
IO = 300 mA
−
0.6
0.8
V
IO = 400 mA
−
0.6
1.1
V
VO ≥ 8.5 V
0.5
1
−
A
Backup switch
IDC(BU)
continuous current
VBUCAP ≥ 6 V
0.4
1.5
−
A
Vclamp(BU)
clamping voltage
VP = 30 V;
IO(REG2) = 100 mA
−
24
28
V
Vdrop
dropout voltage
IO = 500 mA;
(VP − VBUCAP)
−
0.6
0.8
V
Notes
1. The quiescent current is measured in standby mode when RL = ∞.
2. The rise and fall times are measured with a 50 pF load capacitor.
3. The reset delay time depends on the value of the reset delay capacitor:
C RESCAP
3
t d ( rst ) = ------------------------ × V th ( rst ) = C RESCAP × ( 750 × 10 ) [ s ]
I ch
4. The dropout voltage of a regulator is the voltage difference between VP and VO(REGn).
5. At current limit, VO(REGn) is held constant (see Fig.6).
6. The foldback current protection limits the dissipation power at short-circuit (see Fig.6).
7. The dropout voltage of regulator 2 is the voltage difference between VBUCAP and VO(REG2).
2004 Feb 24
28
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
Vp
DIAG
VO(REG3)
Regulator switched off
when amplifier is
completely muted
Amplifier status
DB2 bit D7
IB1 bit D0
IB2 bit D4
twake
STB
SVR
tmute(off)
Soft
mute
Amplifier
output
Soft
mute
mrc350
Fig.12 Start-up and shut-down timing.
2004 Feb 24
29
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
handbook, full pagewidth
VO
(V)
14.4
Vp
Headroom protection activated:
1) fast mute
2) discharge of SVR
Low Vp mute activated
8.8
8.6
Output
voltage
Headroom voltage
7.2
Low Vp mute released
SVR voltage
3.5
DIAG
DB2 bit D7
VO(REG3)
MRC348
Fig.13 Low VP behaviour at VP > 5.5 V.
2004 Feb 24
30
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
VO
(V)
14.4
Vp
TDA8589J; TDA8589xJ
Low Vp mute activated
POR activated
8.8
8.6
7.2
5.5
3.5
SVR voltage
DIAG
DB2 bit D7
POR has occured
VO(REG3)
mrc349
Fig.14 Low VP behaviour at VP < 5.5 V.
2004 Feb 24
31
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
V
(V)
TDA8589J; TDA8589xJ
VP
Vth(rst)
VO(REG2)
VRST
t (sec)
td(rst)
mdb511
Fig.15 Reset delay function.
2004 Feb 24
32
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
Performance diagrams
THD AS A FUNCTION OF OUTPUT POWER Po AT DIFFERENT FREQUENCIES
MRC339
102
handbook, full pagewidth
THD
(%)
10
1
(1)
10−1
(2)
10−2
(3)
(4)
10−3
10−2
(1)
(2)
(3)
(4)
10−1
f = 10 kHz (channels 1 to 4).
f = 100 Hz and 1 kHz (channels 1 and 2).
f = 1 kHz (channels 3 and 4).
f = 100 Hz (channels 3 and 4).
1
VP = 14.4 V.
RL = 4 Ω.
Fig.16 THD as a function of Po.
2004 Feb 24
33
10
Po (W)
102
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
THD AS A FUNCTION OF FREQUENCY AT DIFFERENT OUTPUT POWERS
MRC340
10
handbook, full pagewidth
THD
(%)
1
10−1
(1)
(2)
10−2
10−3
10−2
(1) Po = 1 W.
(2) Po = 10 W.
10−1
1
10
VP = 14.4 V.
RL = 4 Ω.
Fig.17 THD as a function of frequency (channels 1 and 2).
2004 Feb 24
34
f (kHz)
102
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
MRC336
10
handbook, full pagewidth
THD
(%)
1
10−1
(1)
10−2
10−3
10−2
(1) Po = 1 W.
(2) Po = 10 W.
10−1
1
(2)
10
VP = 14.4 V.
RL = 4 Ω.
Fig.18 THD as a function of frequency (channels 3 and 4).
2004 Feb 24
35
f (kHz)
102
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
LINE DRIVER MODE
MRC337
1
handbook, full pagewidth
THD
(%)
10−1
10−2
10−3
10−1
1
10
VP = 14.4 V.
RL = 600 Ω.
f = 1 kHz.
Fig.19 THD as a function of Vo in balanced line driver mode.
2004 Feb 24
36
Vo(rms)
(V)
102
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
OUTPUT POWER AS A FUNCTION OF FREQUENCY AT DIFFERENT THD LEVELS
MRC346
30
handbook, full pagewidth
Po
(W)
(1)
25
(2)
20
(3)
15
10−2
(1) THD = 10 %.
(2) THD = 5 %.
(3) THD = 0.5 %.
10−1
1
VP = 14.4 V.
Fig.20 Po as a function of frequency; RL = 4 Ω.
2004 Feb 24
37
10
f (kHz)
102
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
MRC347
45
handbook, full pagewidth
(1)
Po
(W)
40
(2)
35
(3)
30
25
10−2
(1) THD = 10 %.
(2) THD = 5 %.
(3) THD = 0.5 %.
10−1
1
VP = 14.4 V.
Fig.21 Po as a function of frequency; RL = 2 Ω.
2004 Feb 24
38
10
f (kHz)
102
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
OUTPUT POWER (PO) AS A FUNCTION OF SUPPLY VOLTAGE (VP)
mdb532
100
Po
(W)
80
60
(1)
40
(2)
(3)
20
0
8
10
12
14
16
18
20
VP (V)
(1) Maximum power.
(2) THD = 10 %.
(3) THD = 0.5 %.
f = 1 kHz.
Fig.22 Po as a function of supply voltage; RL = 4 Ω.
2004 Feb 24
39
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
MRC334
100
handbook, full pagewidth
Po
(W)
80
(1)
60
(2)
40
(3)
20
0
8
(1) Maximum power.
(2) THD = 10 %.
(3) THD = 0.5 %.
12
16
f = 1 kHz.
Fig.23 Po as a function of supply voltage; RL = 2 Ω.
2004 Feb 24
40
Vp (V)
20
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
SUPPLY VOLTAGE RIPPLE REJECTION IN OPERATING AND MUTE MODES
MRC341
84
handbook, full pagewidth
SVRR
(dB)
80
(1)
76
72
(2)
68
64
60
10−1
VP = 14.4 V.
RL = 4 Ω.
Vripple = 2 V (p-p).
Rsource = 600 Ω.
1
(1) Operating mode.
(2) Mute mode.
Fig.24 SVRR as a function of frequency.
2004 Feb 24
41
f (kHz)
10
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
CHANNEL SEPARATION AS A FUNCTION OF FREQUENCY
MRC338
100
handbook, full pagewidth
αcs
(dB)
90
80
70
60
50
10−2
10−1
1
VP = 14.4 V.
RL = 4 Ω.
Po = 4 W.
Rsource = 600 Ω.
Fig.25 Channel separation.
2004 Feb 24
42
10
f (kHz)
102
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
POWER DISSIPATION AND EFFICIENCY
MRC342
50
handbook, full pagewidth
Ptot
(W)
40
30
20
10
0
0
10
20
Po (W)
VP = 14.4 V.
RL = 4 Ω.
f = 1 kHz.
Fig.26 Amplifier dissipation as a function of output power; all channels driven.
2004 Feb 24
43
30
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
MRC343
100
handbook, full pagewidth
η
(%)
80
60
40
20
0
0
8
16
24
32
Po (W)
VP = 14.4 V.
RL = 4 Ω.
f = 1 kHz.
Fig.27 Amplifier efficiency as a function of output power; all channels driven.
2004 Feb 24
44
40
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
APPLICATION AND TEST INFORMATION
BUCAP
37 REG2
REGULATOR 2
1000 µF
(16 V)
36
220 nF
VP
220 µF
(16 V)
100 nF
TEMPERATURE &
LOAD DUMP
PROTECTION VOLTAGE
REGULATOR
REFERENCE
VOLTAGE
BACKUP
SWITCH
14.4 V
microcontroller
10 µF
(50 V)
35
30 REG1
REGULATOR 1
audio
10 µF
(50 V)
220 nF
TDA8589
100 nF
mechanical
digital
31 REG3
REGULATOR 3
10 µF
(50 V)
mechanical
drive
33 REG4
REGULATOR 4
ENABLE
LOGIC
100 nF
10 µF
(50 V)
100 nF
34 REG5
REGULATOR 5
Vreg2
display
10 µF
(50 V)
SWITCH 1
100 nF
29 SW1
amplifiers
10 µF
(50 V)
SWITCH 2
40 µs
RESCAP
100 nF
27 SW2
aerial
motor
10 µF
(50 V)
28
100 nF
26 RST
47 nF
microcontroller
32 GND
SDA
SCL
STB
20 VP1
2
25 DIAG
22
14.4 V
6 VP2
4
I2C-BUS
INTERFACE
STANDBY/ MUTE
CLIP DETECT/ DIAGNOSTIC
10 kΩ
220
nF
(1)
220
nF
2200 µF
(16 V)
microcontroller
RS
IN1
MUTE
11
26 dB/
20 dB
470 nF
9
OUT1+
7
OUT1−
17
OUT2+
19
OUT2−
5
OUT3+
3
OUT3−
21
OUT4+
23
OUT4−
PROTECTION/
DIAGNOSTIC
RS
IN2
MUTE
15
26 dB/
20 dB
470 nF
PROTECTION/
DIAGNOSTIC
RS
IN3
MUTE
12
26 dB/
20 dB
470 nF
PROTECTION/
DIAGNOSTIC
RS
IN4
470 nF
MUTE
14
26 dB/
20 dB
VP
PROTECTION/
DIAGNOSTIC
TEMPERATURE & LOAD
DUMP PROTECTION
AMPLIFIER
10
SVR
22 µF
13
16
SGND
2.2 µF
(4 × 470 nF)
ACGND
8
1
18
24
PGND1 PGND2/TAB PGND3 PGND4
mdb539
ACGND capacitor value must be close to 4 × input capacitor value.
For EMC reasons, a capacitor of 10 nF can be connected between each amplifier output and ground.
Fig.28 Test and application diagram.
2004 Feb 24
45
(1) See “Supply decoupling”.
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
Supply decoupling
(see Fig.28)
The high frequency 220 nF decoupling capacitors connected to power supply voltage pins 6 and 20 should be located
as close as possible to these pins.
It is important to use good quality capacitors. These capacitors should be able to suppress high voltage peaks that can
occur on the power supply if several audio channels are accidentally shorted to the power supply simultaneously, due to
the activation of current protection. Good results have been achieved using 0805 case-size capacitors (X7R material,
220 nF) located close to power supply voltage pins 6 and 20.
2004 Feb 24
46
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
PCB layout
handbook, full pagewidth
MDB533
Fig.29 Top of printed-circuit board layout of test and application circuit showing copper layer viewed from top.
handbook, full pagewidth
MDB534
Fig.30 Bottom of printed-circuit board layout of test and application circuit showing copper layer viewed from top.
2004 Feb 24
47
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
DZ 5.6 V
Mode
TDA8589J; TDA8589xJ
Sense
GND
VP
1000 µF
220 µF
CBU
on
2200 µF
10 µF (50 V)
TDA8589J
off
22 µF
SDA
+5V
GND
SCL
REG5
10 µF (50 V)
470 nF
REG2
10 µF (50 V)
GND
VP
RGND
10 µF (50 V)
2.2 µF
470 nF
REG4
REG3
47 nF on
10 µF
OUT
SGND
OUT
RESCAP
DIAG
off
10 µF (50 V)
4.7 kΩ
REG1
SW1
SW2
IN
I2C supply
RST
RESCAP
mdb535
Fig.31 Top of printed-circuit board layout of test and application circuit showing components viewed from top.
handbook, full pagewidth
100 nF
220 nF
100 nF
220 nF
10 kΩ
220 nF
47 kΩ
100 nF
100 nF
MDB536
Fig.32 Bottom of printed-circuit board layout of test and application circuit showing components viewed from
bottom.
2004 Feb 24
48
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
Beep input circuit
Beep input circuit to amplify the beep signal from the microcontroller to all 4 amplifiers (gain = 0 dB). Note that this circuit
will not affect amplifier performance.
TDA8589
ACGND
2.2 µF
From
microcontroller
1.7 kΩ
0.22 µF
100 Ω
47 pF
mdb537
Fig.33 Application diagram for beep input.
Noise
The outputs of regulators 1 to 5 are designed to give very low noise with good stability. The noise output voltage depends
on output capacitor Co. Table 11 shows the affect of the output capacitor on the noise figure.
Table 11 Regulator noise figures
REGULATOR
NOISE FIGURE (µV) at IREG = 10 mA; note 1
Co = 10 µF
Co = 47 µF
Co = 100 µF
1
225
195
185
2
750
550
530
3
120
100
95
4
225
195
185
5
320
285
270
Note
1. Measured in the frequency range 20 Hz to 80 kHz.
Stability
The regulators are made stable by connecting capacitors to the regulator outputs. The stability can be guaranteed with
almost any output capacitor if its Electric Series Resistance (ESR) stays below the ESR curve shown in Fig.34. If an
electrolytic capacitor is used, its behaviour with temperature can cause oscillations at extremely low temperature.
Oscillation problems can be avoided by adding a 47 nF capacitor in parallel with the electrolytic capacitor. The following
example describes how to select the value of output capacitor.
2004 Feb 24
49
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
EXAMPLE REGULATOR 2
Regulator 2 (BU5V) is stabilized with an electrolytic output capacitor of 10 µF which has an ESR of 4 Ω. At Tamb = −30 °C
the capacitor value decreases to 3 µF and its ESR increases to 28 Ω which is above the maximum allowed as shown
in Fig.34, and which will make the regulator unstable. To avoid problems with stability at low temperatures, the
recommended solution is to use tantalum capacitors. Either use a tantalum capacitor of 10 µF, or an electrolytic capacitor
with a higher value.
MGL912
handbook, halfpage
20
ESR
(Ω)
15
maximum ESR
10
5
stable region
0
0.1
10
1
C (µF)
100
Fig.34 Curve for selecting the value of output capacitors for regulators 1 to 5.
2004 Feb 24
50
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
PACKAGE OUTLINE
DBS37P: plastic DIL-bent-SIL power package; 37 leads (lead length 6.8 mm)
SOT725-1
non-concave
Dh
x
D
Eh
view B: mounting base side
A2
d
B
j
E
A
L4
L3
L
1
L2
37
e1
Z
w M
bp
e
c
Q
v M
e2
m
0
10
20 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
A2
mm
19
4.65 0.60
4.35 0.45
bp
c
0.5
0.3
D(1)
d
42.2 37.8
41.7 37.4
Dh
E(1)
e
e1
e2
Eh
j
L
L2
12
15.9
15.5
2
1
4
8
3.4
3.1
6.8
3.9
3.1
L3
L4
1.15 22.9
0.85 22.1
m
Q
v
4
2.1
1.8
0.6
w
x
0.25 0.03
Z(1)
3.30
2.65
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT725-1
---
---
---
2004 Feb 24
51
EUROPEAN
PROJECTION
ISSUE DATE
01-11-14
02-11-22
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
The total contact time of successive solder waves must not
exceed 5 seconds.
SOLDERING
Introduction to soldering through-hole mount
packages
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg(max)). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
This text gives a brief insight to wave, dip and manual
soldering. A more in-depth account of soldering ICs can be
found in our “Data Handbook IC26; Integrated Circuit
Packages” (document order number 9398 652 90011).
Wave soldering is the preferred method for mounting of
through-hole mount IC packages on a printed-circuit
board.
Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300 °C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400 °C, contact may be up to 5 seconds.
Soldering by dipping or by solder wave
Driven by legislation and environmental forces the
worldwide use of lead-free solder pastes is increasing.
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250 °C or 265 °C, depending on solder
material applied, SnPb or Pb-free respectively.
Suitability of through-hole mount IC packages for dipping and wave soldering methods
SOLDERING METHOD
PACKAGE
DIPPING
WAVE
DBS, DIP, HDIP, RDBS, SDIP, SIL
suitable
suitable(1)
PMFP(2)
−
not suitable
Notes
1. For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board.
2. For PMFP packages hot bar soldering or manual soldering is suitable.
2004 Feb 24
52
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
DATA SHEET STATUS
LEVEL
DATA SHEET
STATUS(1)
PRODUCT
STATUS(2)(3)
Development
DEFINITION
I
Objective data
II
Preliminary data Qualification
This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product.
III
Product data
This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in order
to improve the design, manufacturing and supply. Relevant changes will
be communicated via a Customer Product/Process Change Notification
(CPCN).
Production
This data sheet contains data from the objective specification for product
development. Philips Semiconductors reserves the right to change the
specification in any manner without notice.
Notes
1. Please consult the most recently issued data sheet before initiating or completing a design.
2. The product status of the device(s) described in this data sheet may have changed since this data sheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
DEFINITIONS
DISCLAIMERS
Short-form specification  The data in a short-form
specification is extracted from a full data sheet with the
same type number and title. For detailed information see
the relevant data sheet or data handbook.
Life support applications  These products are not
designed for use in life support appliances, devices, or
systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips
Semiconductors customers using or selling these products
for use in such applications do so at their own risk and
agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Limiting values definition  Limiting values given are in
accordance with the Absolute Maximum Rating System
(IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device.
These are stress ratings only and operation of the device
at these or at any other conditions above those given in the
Characteristics sections of the specification is not implied.
Exposure to limiting values for extended periods may
affect device reliability.
Right to make changes  Philips Semiconductors
reserves the right to make changes in the products including circuits, standard cells, and/or software described or contained herein in order to improve design
and/or performance. When the product is in full production
(status ‘Production’), relevant changes will be
communicated via a Customer Product/Process Change
Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these
products, conveys no licence or title under any patent,
copyright, or mask work right to these products, and
makes no representations or warranties that these
products are free from patent, copyright, or mask work
right infringement, unless otherwise specified.
Application information  Applications that are
described herein for any of these products are for
illustrative purposes only. Philips Semiconductors make
no representation or warranty that such applications will be
suitable for the specified use without further testing or
modification.
2004 Feb 24
53
Philips Semiconductors
Product specification
I2C-bus controlled 4 × 45 Watt power
amplifier and multiple voltage regulator
TDA8589J; TDA8589xJ
PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
2004 Feb 24
54
Philips Semiconductors – a worldwide company
Contact information
For additional information please visit http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
For sales offices addresses send e-mail to: [email protected].
SCA76
© Koninklijke Philips Electronics N.V. 2004
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
R32/01/pp55
Date of release: 2004
Feb 24
Document order number:
9397 750 11402