NKK MLW3023-24-RA-1A

Rockers
Toggles
Series MLW
B
Snap-in Miniature Rockers
General Specifications
Electrical Capacity
Pushbuttons
Programmable Illuminated PB
Materials & Finishes
Touch
Tilt
Tactiles
Slides
Rotaries
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Angle of Throw: Keylocks
Power Level: 5A @ 125V AC, 3A @ 250V AC, & 3A @ 30V DC
Other Ratings
Housing:
Movable Contacts:
Stationary Contacts:
Base:
Common Terminal:
End Terminals:
Lamp Terminals:
Environmental Data
Operating Temperature Range:
Humidity: Vibration:
Shock:
Stainless steel
Silver alloy
Silver
Phenolic resin
Copper with silver plating
Copper with silver plating
Phosphor bronze with nickel plating
–10°C through +50°C (+14°F through +122°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 3 right angled directions, with 3 shocks in each direction)
Installation
Cap Installation Force: 9.80N (2.2 lbf) for rockers;
19.61N (4.4 lbf) for paddle
Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section.
Standards & Certifications
UL:
File No. E44145
All models recognized at 5A @ 125V AC & 3A @ 250V AC.
Add “/U” to end of part number to order UL mark on switch.
Add “/CUL” to end of part number to order cULus mark on switch.
Supplement
Accessories
Indicators
10 milliohms maximum
200 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
30,000 operations minimum
10,000 operations minimum
9.94N for rockers & 4.41N for paddles
24° for On-None-(On); 28° for all other circuits
B106
www.nkk.com
Distinctive Characteristics
B
Rockers
Toggles
Series MLW
Snap-in Miniature Rockers
Pushbuttons
Industry’s first miniature snap-in, lighted rocker switch.
Programmable Illuminated PB
Actuators in various styles operate with firm, well-defined
movements.
Interlocking actuator prevents switch failure due to
jamming or window locking.
Two bezel sizes adapt to varied panel cutouts.
Keylocks
Unique stainless steel retaining clips securely hold
switches over a range of panel thicknesses, even
when exposed to vibration.
Rotaries
Space conserving front panel mounting with
minimum behind panel dimension of .902”
(22.9mm).
Slides
Durable stainless steel housing prevents corrosion.
Tactiles
Isolated lamp circuit for incandescent, LED, and neon lamps.
Front panel relamping.
Built-in protective cover shields contacts from dust.
Tilt
Epoxy sealed solder lug terminals lock out flux, dust, and other
contaminants.
Touch
Extended lamp terminal for ease of wiring.
Matching indicators available.
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
B107
Snap-in Miniature Rockers
TYPICAL SWITCH ORDERING EXAMPLE
2
M LW 3 0
B
Poles
5
Lamps
1
SPDT
2
SP3T
DPDT
12
1A
DC
Cap Types & Colors
Bezels/Colors
Rocker
Standard
Incandescent & Neon Lamps
Circuits
00
No Lamp
RA
1A
Black
06
6-volt
RB
White
1B
White
12
12-volt
RC
Red
1C
Red
Black
18
18-volt
RD
Orange
1D
Orange
2
ON
NONE
ON
24
24-volt
RE
Yellow
1E
Yellow
3
ON
OFF
ON
28
28-volt
RF
Green
1F
Green
5
ON
NONE
(ON)
1G
Blue
OFF
(ON)
110-volt (not suitable
with green & blue)
Blue
(ON)
N
RG
8
Paddle
1H
Gray
9
ON
OFF
(ON)
PA
Black
0
ON
ON
ON
PB
White
2A
Black
PC
Red
2B
White
PD
Orange
2C
Red
PE
Yellow
2D
Orange
PF
Green
2E
Yellow
PG
Blue
2F
Green
2G
Blue
2H
Gray
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
Toggles
Series MLW
Slides
( ) = Momentary
Design Rocker
C
Red
DB
White
E
Yellow
DC
Red
F
Green
DD
Orange
DF
Green
Tilt
Tactiles
Single Element LED Colors
DG
Large
Blue
LED Rocker
LB
White
MLW3025-12-DC-1A
LC
Red
LE
Yellow
LF
Green
Design Cap
(Black Rocker Base
with Red Filter)
DPDT
ON-NONE-(ON)
Circuit
Supplement
Accessories
Indicators
Touch
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
12-volt
Incandescent Lamp
Black .787”
(20.0mm)
Wide Bezel
Sculptured Rocker
SB
White
SC
Red
SE
Yellow
SF
Green
Note: Wire harness & cable assemblies
offered only in Americas
B108
www.nkk.com
IMPORTANT:
Switches are supplied
without UL, cULus &
CSA markings unless
specified. Specific
models & ratings noted
on General
Specifications
page.
Series MLW
Toggles
Snap-in Miniature Rockers
POLES & CIRCUITS
Down
MLW3012
MLW3013
MLW3015
MLW3018
MLW3019
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
MLW3022
MLW3023
MLW3025
MLW3028
MLW3029
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
SP
DP
Up
Center
Down
Notes: Terminal numbers are not actually on
switch. Lamp circuit is isolated and
requires an external power source.
SPDT
2-1
OPEN
2 (COM)
2-3
L (+)
(-) L
L (+)
(-) L
1
3
DPDT
2-1 5-4
OPEN
2 (COM)
2-3 5-6
3
1
5
6
4
For 3 Throw (3-On)
Model
Up
SP MLW3020 ON
Center Down
ON
Connected Terminals & Schematics
External
Connection
2 (in)
5
External
Connection
2 (in)
5
ON
External Connection
The SP3T model utilizes
a double pole base.
External
Connection
2 (in)
5
Keylocks
Pole
(out)
1 (out)
With External Connection
Without External Connection
3 4 (out) 6 (out) 1 (out)
3 4 (out) 6 (out) 1 (out)
3 4 (out) 6 (out)
2-1
2-4
2-6
2-1 5-4
2-3 5-4
2-3 5-6
External
connection
must be made
during field
installation.
External
Conn
6
3
5
2
4
1
(out)
Common
(in)
(out)
(5.9)
.232
(2.0)
.079
(1.1)
.043
Thk = (0.8)
.031
(1.2) Dia
.047
(3.0)
.118
Tactiles
Center terminal is
.020” (0.5mm) longer
Lamp Terminals
(4.0)
.157
(2.0)
.079
Slides
TERMINALS
Switch Terminals.
B
Rockers
Center
Model
Pushbuttons
Up
Pole
Throw & Power/Lamp Schematics
Programmable Illuminated PB
Connected Terminals
( ) = Momentary
Rotaries
Rocker Position
Thk = (0.8)
.031
LAMP CODES & SPECIFICATIONS
Tilt
Electrical specifications are determined at a basic temperature of 25°C. Lamp circuit is independent of switch operation.
For dimension drawings of lamps see Accessories & Hardware section.
For neon, if the source voltage is greater than rated voltage, a ballast resistor is required.
The ballast resistor calculation and more lamp detail are shown in the Supplement.
L(-)
06
12
18
24
28
N
Voltage
V
6V AC
12V AC
18V AC
24V AC
28V AC
110V AC
Current
I
80mA
50mA
35mA
25mA
22mA
1.5mA
.159
.215
.398
.215
.247
NA
MSCP
Endurance
Indicators
L(+)
Hours
2,000 Average
15,000 Average
Ambient Temperature Range
–10°C ~ +50°C
–10°C ~ +50°C
T-11⁄2 Pilot Slide Base
00
Supplement
Recommended Resistor for Neon: 33K ohms for 110V AC; 100K ohms for 220V AC
No Lamp Code 00 indicates that no lamp is used.
www.nkk.com
Accessories
AT602
AT602N
Incandescent
Neon
Touch
Incandescent & Neon Lamps for Solid & Design Caps
B109
Series MLW
LED COLOR CODES & SPECIFICATIONS
Single Element LED
(+)
(-)
C
Color
Red
Yellow
F
Green
Forward Peak Current
I FM
30mA
30mA
30mA
Continuous Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
1.85V
2.0V
2.1V
Reverse Peak Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆I F
0.40mA/°C
0.40mA/°C
0.40mA/°C
Ambient Temperature Range
T-1 ⁄ Pilot Slide Base
34
E
–10°C ~ +50°C
CAP TYPES & COLORS
For Incandescent or Neon Lamps
RA
Rotaries
Keylocks
Programmable Illuminated PB
Resistor value calculation is shown
in the Supplement.
AT622 LED
B
Pushbuttons
Rockers
Toggles
Snap-in Miniature Rockers
AT405 Rocker
RB
RE
RC
RF
RD
RG
AT426 Paddle
PA
(16.0)
.630
(12.6)
.496
(10.5)
.413
(4.0)
.157
PB
PE
PC
PF
PD
PG
(25.0)
.984
Slides
Tactiles
For LED
SB
LC
SC
LE
Translucent
Colored Diffuser
and Opaque Black
Rocker Base
Tilt
LF
(12.6)
.496
(16.0)
.630
(13.5)
.531
(10.5)
.413
Translucent Colored Filter
Opaque Black Rocker Base
AT4127
Sculptured
Rocker
(11.5)
.453
SE
(13.5)
.531
(10.5)
.413
(12.6)
.496
(16.0)
.630
DG
Material: Translucent Polycarbonate Standard Finish: Glossy
Black Rocker/Paddle not for use with lamp
LB
Touch
DD
DF
(15.6)
.614
AT4125
LED Rocker
AT438 Design Rocker
DC
(13.5)
.531
DB
(15.6)
.614
SF
(15.5)
.610
(16.0)
.630
Material: Translucent Polycarbonate Standard Finish: Glossy
Color Codes:
A
Black
B
C
White
Red
D
Orange
E
Yellow
F
G
Green
Blue
Indicators
OPTIONAL BEZELS
1A
Accessories
Supplement
AT9201 Large Bezel .937” (23.8mm) Wide
AT204 Standard Bezel .787” (20.0mm) Wide
1B
1E
1F
1C
1G
1D
1H
B110
(16.4)
.646
(2.2)
.087
(16.0)
.630
(20.0)
.787
(25.5)
1.004
Material: PolycarbonateStandard Finish: Glossy
www.nkk.com
2A
2E
2B
2F
2C
2G
2D
2H
(16.4)
.646
(2.5)
.098
(23.8)
.937
(16.0)
.630
(26.3)
1.035
Material: Polycarbonate Standard Finish: Glossy
Series MLW
TYPICAL SWITCH DIMENSIONS
(5.4)
.213
(0.5)
.020
(5.9)
.232
(22.0)
.866
Actuator in UP position
.157
(4.5)
.177
(15.6)
.614
(15.5)
.611
(5.4)
.213
(0.5)
.020
(22.0)
.866
(5.9)
.232
Actuator in UP position
(6.1)
.240
(0.5)
.020
(22.0)
.866
Actuator in UP position
5
2
4
1
(1.1) x (2.0) Typ
.043 x .079
(5.9)
.232
(1.2) Dia Typ
.047
(10.2)
.402
(20.0)
.787
(2.0) Typ
.079
(3.0) Typ
.118
L (-)
6
Programmable Illuminated PB
MLW3022-12-RC-1A
Large Bezel
Single & Double Pole
3
5
2
4
1
(26.3)
1.035
L (+)
(10.2)
.402
(16.6)
.654
(23.8)
.937
(3.0) Typ
.118
6
(2.0) Typ
.079
L (-)
MLW3022-12-PC-2A
Sculptured Cap
Single & Double Pole
3
5
2
4
1
(25.5)
1.004
L (+)
(10.2)
.402
(16.6)
.654
(20.0)
.787
Terminals 4, 5, & 6 are not on single pole models
www.nkk.com
Pushbuttons
(25.5)
1.004
L (+)
(1.2) Dia Typ
.047
(0.8) Typ
.031
(4.7) Typ
.185
(17.0)
.669
(0.4) Typ
.016
(16.0)
.630
3
Terminals 4, 5, & 6 are not on single pole models
(4.5)
.177
MLW3022-12-PC
Standard Bezel
Single & Double Pole
(1.1) x (2.0) Typ
.043 x .079
(4.0)
NKK Part No.
.157
This Side
(2.2)
.087
L (-)
6
(16.6)
.654
(0.8) Typ
.031
(4.7) Typ
.185
(17.0)
.669
(0.4) Typ
.016
(2.5)
.098
(2.0) Typ
.079
Terminals 4, 5, & 6 are not on single pole models
This Side
(2.5)
.098
(3.0) Typ
.118
(1.2) Dia Typ
.047
(4.0)
NKK Part No.
(4.0)
.157
(10.2)
.402
(16.6)
.654
Tilt
(1.1) x (2.0) Typ
.043 x .079
(0.8) Typ
.031
(4.7) Typ
.185
(17.0)
.669
(0.4) Typ
.016
(15.6)
.614
(15.5)
.611
L (+)
Keylocks
(4.5)
.177
(2.2)
.087
(21.0)
.827
Rotaries
(4.0)
(2.2)
.087
1
Terminals 4, 5, & 6 are not on single pole models
NKK Part No.
.157
This Side
(4.0)
.157
2
4
Tactiles
Actuator in UP position
5
(1.2) Dia Typ
.047
B
3
Touch
(22.9)
.902
(4.5)
.177
(5.9)
.232
L (-)
6
Indicators
(14.5)
.571
(1.1) x (2.0) Typ
.043 x .079
Without Bezel
Single & Double Pole
Accessories
(0.5)
.020
(0.5)
.020
(2.0) Typ
.079
(3.0) Typ
.118
(0.8) Typ
.031
(4.7) Typ
.185
(17.0)
.669
(0.4) Typ
.016
(15.6)
.614
(4.0)
.157
(16.0)
.630
.157
(4.5)
.177
This Side
MLW3022-C-SC-1A
B111
Supplement
.059
Slides
(4.0)
(1.5)
NKK Part No.
Rockers
Toggles
Snap-in Miniature Rockers
(18.7)
.736
B
(16.7)
.657
Programmable Illuminated PB
(19.2) Sq
.755
(16.7)
.657
Without Bezel
.039” ~ .157” (1.0mm ~ 4.0mm)
With Standard Bezel AT204
.039” ~ .118” (1.0mm ~ 3.0mm)
With Large Bezel AT9201
.039” ~ .118” (1.0mm ~ 3.0mm)
INSTALLATION & MAINTENANCE
Lamps and LEDs can be changed without
removing the switch from the panel. The
lamp extractor AT107 assists in removing
lamps and LEDs.
AT107
Lamp Extractor
(3.8) Dia
.150
LED (+) Marking this side
Actuator (+) Marking
(5.0) Dia
.197
Note: When changing LEDs, match
the positive polarity markings on
both lamp base and actuator block.
(20.0)
.787
LEGENDS
Rotaries
Keylocks
(18.7)
.736
Slides
NKK Switches can provide custom legends for caps. Contact factory for more information.
Rocker
STA
RT
Tactiles
Design Rocker & LED Rocker
(1.52) Typ
.060
OP
ST
Tilt
Snap-in Miniature Rockers
PANEL CUTOUTS & THICKNESSES
Pushbuttons
Rockers
Toggles
Series MLW
(9.56)
.376
Recommended Print Method:
Pad Print
(14.48)
.570
Bezel
(1.52) Typ
.060
(12.6)
.496
(8.16)
.321
(13.08)
.515
(0.76) Typ
.030
(14.6)
.575
(16.0)
.630
(3.15) Typ
.124
(11.2)
.441
(0.76) Typ
.030
(4.67) Typ
.184
(0.76) Typ
.030
(0.76) Typ
.030
(20.0)
.787
Epoxy based ink is recommended
Supplement
Accessories
Indicators
Touch
Shaded areas are printable areas.
B112
(18.48) Typ
.728
www.nkk.com
(0.76) Typ
.030