ATMEL AT45DB1282-CC

Features
• Single 2.7V - 3.6V Supply
• Dual-interface Architecture
•
•
•
•
•
•
•
•
•
•
– RapidS™ Serial Interface: 40 MHz Maximum Clock Frequency
(SPI Modes 0 and 3 Compatible for Frequencies up to 33 MHz)
– Rapid8™ 8-bit Interface: 20 MHz Maximum Clock Frequency
Page Program Operation
– Dedicated Intelligent Programming Operation
– 16,384 Pages (1,056 Bytes/Page) Main Memory
Automated Page and Block Erase Operations
Two 1056-byte SRAM Data Buffers – Allows Receiving of Data
while Reprogramming the Flash Array
Continuous Read Capability through Entire Array
– Ideal for Code Shadowing Applications
Low-power Dissipation
– 10 mA Active Read Current Typical – Serial Interface
– 12 mA Active Read Current Typical – 8-bit Interface
– 5 µA CMOS Standby Current Typical
Hardware Data Protection
Security: 128-byte Security Register
– 64-byte User Programmable Space
– Unique 64-byte Device Identifier
100,000 Program/Erase Cycles Per Page Typical
Data Retention – 10 Years
Commercial and Industrial Temperature Ranges
128-megabit
2.7-volt
Dual-interface
DataFlash®
AT45DB1282
Preliminary
Description
The AT45DB1282 is a 2.7-volt, dual-interface sequential access Flash memory ideally
suited for a wide variety of digital voice-, image-, program code- and data-storage
Pin Configurations
Pin Name
Function
CS
Chip Select
SCK/CLK
Serial Clock/Clock
SI
Serial Input
SO
Serial Output
I/O7 - I/O0
8-bit Input/Output
WP
Hardware Page Write
Protect Pin
RESET
Chip Reset
RDY/BUSY
Ready/Busy
SER/BYTE
Serial/8-bit Interface
Control
™
TSOP Top View: Type 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
NC
NC
RDY/BUSY
RESET
WP
NC
NC
NC
VCC
GND
NC
NC
NC
NC
CS
SCK
SI*
SO*
NC
NC
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
NC
NC
NC
NC
NC
I/O7*
I/O6*
I/O5*
I/O4*
VCCP*
GNDP*
I/O3*
I/O2*
I/O1*
I/O0*
SER/BYTE*
CLK
NC
NC
NC
CBGA Top View
4
5
NC SER/BYTE NC
I/O7
I/O6
I/O2 SCK/CLK GND
VCC
I/O5
I/O1
CS RDY/BUSY WP
I/O4
I/O0
SO
1
2
3
A
B
C
D
E
F
SI
RESET I/O3
G
NC
GNDP VCCP
NC
NC
H
Note:
*Optional Use – See pin description text
for connection information.
J
Rev. 2472C–DFLSH–11/03
1
applications. This device utilizes Atmel’s e- STAC ™ Multi-Level Cell (MLC) memory
technology, which allows a single cell to store two bits of information delivering a
very cost effective high density Flash memory. The AT45DB1282 supports RapidS
serial interface and Rapid8 8-bit interface. RapidS serial interface is SPI compatible for
frequencies up to 33 MHz. The dual-interface allows a dedicated serial interface to be
connected to a DSP and a dedicated 8-bit interface to be connected to a microcontroller
or vice versa. However, the use of either interface is purely optional. Its 138,412,032 bits
of memory are organized as 16,384 pages of 1,056 bytes each. In addition to the 132megabit main memory, the AT45DB1282 also contains two SRAM buffers of 1,056
bytes each. The buffers allow the receiving of data while a page in the main Memory is
being reprogrammed, as well as writing a continuous data stream. EEPROM emulation
(bit or byte alterability) is easily handled with a self-contained three step read-modifywrite operation. Unlike conventional Flash memories that are accessed randomly with
multiple address lines and a parallel interface, the DataFlash uses either a RapidS serial
interface or a 8-bit Rapid8 interface to sequentially access its data. The simple sequential access dramatically reduces active pin count, facilitates hardware layout, increases
system reliability, minimizes switching noise, and reduces package size. The device is
optimized for use in many commercial and industrial applications where high-density,
low-pin count, low-voltage and low-power are essential. The device operates at clock
frequencies up to 40 MHz with a typical active read current consumption of 10 mA.
To allow for simple in-system reprogrammability, the AT45DB1282 does not require
high input voltages for programming. The device operates from a single power supply,
2.7V to 3.6V, for both the program and read operations. The AT45DB1282 is enabled
through the chip select pin (CS) and accessed via a three-wire interface consisting of
the Serial Input (SI), Serial Output (SO), and the Serial Clock (SCK), or an 8-bit interface
consisting of the input/output pins (I/O7 - I/O0) and the clock pin (CLK).
All programming and erase cycles are self-timed.
Block Diagram
FLASH MEMORY ARRAY
WP
PAGE (1056 BYTES)
BUFFER 1 (1056 BYTES)
SCK/CLK
CS
RESET
VCC
GND
RDY/BUSY
SER/BYTE
Memory Array
2
BUFFER 2 (1056 BYTES)
I/O INTERFACE
SI
SO
I/O7 - I/O0
To provide optimal flexibility, the memory array of the AT45DB1282 is divided into three
levels of granularity comprising of sectors, blocks, and pages. The “Memory Architecture Diagram” illustrates the breakdown of each level and details the number of pages
per sector and block. All program operations to the DataFlash occur on a page by page
basis. The erase operations can be performed at the block or page level.
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Memory Architecture Diagram
SECTOR 1 = 248 Pages
261,888 bytes (248K + 7,936)
SECTOR 0
BLOCK 0
BLOCK 1
SECTOR 1
SECTOR 0 = 8 Pages
8,448 bytes (8K + 256)
BLOCK ARCHITECTURE
BLOCK 2
PAGE ARCHITECTURE
8 Pages
PAGE 0
BLOCK 0
SECTOR ARCHITECTURE
BLOCK 33
PAGE 9
PAGE 14
PAGE 15
BLOCK 62
PAGE 16
BLOCK 63
PAGE 17
BLOCK 64
PAGE 18
SECTOR 63 = 256 Pages
270,336 bytes (256K + 8K)
BLOCK 65
SECTOR 64 = 256 Pages
270,336 bytes (256K + 8K)
BLOCK 2046
Device Operation
BLOCK 1
SECTOR 2
SECTOR 3 = 256 Pages
270,336 bytes (256K + 8K)
PAGE 8
BLOCK 31
BLOCK 32
PAGE 6
PAGE 7
BLOCK 30
SECTOR 2 = 256 Pages
270,336 bytes (256K + 8K)
PAGE 1
PAGE 16,382
BLOCK 2047
PAGE 16,383
Block = 8,448 bytes
(8K + 256)
Page = 1,056 bytes
(1K + 32)
The device operation is controlled by instructions from the host processor. The list of
instructions and their associated opcodes are contained in Tables 1 through 4. A valid
instruction starts with the falling edge of CS followed by the appropriate 8-bit opcode
and the desired buffer or main memory address location. While the CS pin is low, toggling the SCK/CLK pin controls the loading of the opcode and the desired buffer or main
memory address location through either the SI (serial input) pin or the 8-bit input pins
(I/O7 - I/O0). All instructions, addresses, and data are transferred with the most significant bit (MSB) first.
Buffer addressing is referenced in the datasheet using the terminology BFA10 - BFA0 to
denote the 11 address bits required to designate a byte address within a buffer. Main
memory addressing is referenced using the terminology PA13 - PA0 and BA10 - BA0,
where PA13 - PA0 denotes the 14 address bits required to designate a page address
and BA10 - BA0 denotes the 11 address bits required to designate a byte address within
the page.
Read Commands
By specifying the appropriate opcode, data can be read from the main memory or from
either one of the two SRAM data buffers. The DataFlash supports RapidS and Rapid8
protocols for Mode 0 and Mode 3. Please refer to the “Detailed Bit-level Read Timing”
diagrams in this datasheet for details on the clock cycle sequences for each mode.
CONTINUOUS ARRAY READ: By supplying an initial starting address for the main
memory array, the Continuous Array Read command can be utilized to sequentially
read a continuous stream of data from the device by simply providing a clock signal; no
additional addressing information or control signals need to be provided. The DataFlash
incorporates an internal address counter that will automatically increment on every clock
cycle, allowing one continuous read operation without the need of additional address
sequences. To perform a continuous read, an opcode of E8H must be clocked into the
device followed by four address bytes (which comprises 7 don’t care bits plus the 25-bit
page and byte address sequence) and a series of don’t care clock cycles (24 if using the
serial interface or 19 if using the 8-bit interface). The first 14 bits (PA13 - PA0) of the
3
2472C–DFLSH–11/03
25-bit address sequence specify which page of the main memory array to read, and the
last 11 bits (BA10 - BA0) of the 25-bit address sequence specify the starting byte
address within the page. The 24 or 19 don’t care clock cycles that follow the four
address bytes are needed to initialize the read operation. Following the don’t care clock
cycles, additional clock pulses on the SCK/CLK pin will result in data being output on
either the SO (serial output) pin or the eight output pins (I/O7- I/O0).
The CS pin must remain low during the loading of the opcode, the address bytes, the
don’t care bytes, and the reading of data. When the end of a page in main memory is
reached during a Continuous Array Read, the device will continue reading at the beginning of the next page with no delays incurred during the page boundary crossover (the
crossover from the end of one page to the beginning of the next page). When the last bit
(or byte if using the 8-bit interface mode) in the main memory array has been read, the
device will continue reading back at the beginning of the first page of memory. As with
crossing over page boundaries, no delays will be incurred when wrapping around from
the end of the array to the beginning of the array.
A low-to-high transition on the CS pin will terminate the read operation and tri-state the
output pins (SO or I/O7-I/O0). The maximum SCK/CLK frequency allowable for the Continuous Array Read is defined by the fCAR specification. The Continuous Array Read
bypasses both data buffers and leaves the contents of the buffers unchanged.
MAIN MEMORY PAGE READ: A main memory page read allows the user to read data
directly from any one of the 16384 pages in the main memory, bypassing both of the
data buffers and leaving the contents of the buffers unchanged. To start a page read, an
opcode of D2H must be clocked into the device followed by four address bytes (which
comprise 7 don’t care bits plus the 25-bit page and byte address sequence) and a series
of don’t care clock cycles (24 if using the serial interface or 19 if using the 8-bit interface). The first 14 bits (PA13 - PA0) of the 25-bit address sequence specify the page in
main memory to be read, and the last 11 bits (BA10 - BA0) of the 25-bit address
sequence specify the starting byte address within that page. The 24 or 19 don’t care
clock cycles that follow the four address bytes are sent to initialize the read operation.
Following the don’t care bytes, additional pulses on SCK/CLK result in data being output
on either the SO (serial output) pin or the eight output pins (I/O7 - I/O0). The CS pin
must remain low during the loading of the opcode, the address bytes, the don’t care
bytes, and the reading of data. When the end of a page in main memory is reached, the
device will continue reading back at the beginning of the same page. A low-to-high transition on the CS pin will terminate the read operation and tri-state the output pins (SO or
I/O7 - I/O0). The maximum SCK/CLK frequency allowable for the Main Memory Page
Read is defined by the fSCK specification. The Main Memory Page Read bypasses both
data buffers and leaves the contents of the buffers unchanged.
BUFFER READ: Data can be read from either one of the two buffers, using different
opcodes to specify which buffer to read from. With the serial interface, an opcode of
D4H is used to read data from buffer 1, and an opcode of D6H is used to read data from
buffer 2. Likewise with the 8-bit interface an opcode of 54H is used to read data from
buffer 1 and an opcode of 56H is used to read data from buffer 2. To perform a buffer
read, the opcode must be clocked into the device followed by four address bytes comprised of 21 don’t care bits and 11 buffer address bits (BFA10 - BFA0). Following the
four address bytes, additional don’t care bytes (one byte if using the serial interface or
two bytes if using the 8-bit interface) must be clocked in to initialize the read operation.
Since the buffer size is 1056 bytes, 11 buffer address bits are required to specify the first
byte of data to be read from the buffer. The CS pin must remain low during the loading
of the opcode, the address bytes, the don’t care bytes, and the reading of data. When
the end of a buffer is reached, the device will continue reading back at the beginning of
the buffer. A low-to-high transition on the CS pin will terminate the read operation and
tri-state the output pins (SO or I/O7 - I/O0).
4
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Program and Erase Commands
BUFFER WRITE: Data can be clocked in from the input pins (SI or I/O7 - I/O0) into
either buffer 1 or buffer 2. To load data into either buffer, a 1-byte opcode, 84H for buffer
1 or 87H for buffer 2, must be clocked into the device, followed by four address bytes
comprised of 21 don’t care bits and 11 buffer address bits (BFA10 - BFA0). The 11
buffer address bits specify the first byte in the buffer to be written. After the last address
byte has been clocked into the device, data can then be clocked in on subsequent clock
cycles. If the end of the data buffer is reached, the device will wrap around back to the
beginning of the buffer. Data will continue to be loaded into the buffer until a low-to-high
transition is detected on the CS pin.
BUFFER TO MAIN MEMORY PAGE PROGRAM: A previously-erased page within main
memory can be programmed with the contents of either buffer 1 or buffer 2. The programming time is selectable by the system through the use of different opcodes
between a normal mode and a fast mode (the fast program option will consume more
current). A 1-byte opcode, 88H for buffer 1 or 89H for buffer 2 (98H for buffer 1 fast program or 99H for buffer 2 fast program), must be clocked into the device followed by four
address bytes consisting of 7 don’t care bits, 14 page address bits (PA13 - PA0) that
specify the page in the main memory to be written and 11 don’t care bits. When a low-tohigh transition occurs on the CS pin, the part will program the data stored in the buffer
into the specified page in the main memory. It is necessary that the page in main memory that is being programmed has been previously erased using one of the erase
commands (Page Erase or Block Erase). The programming of the page is internally selftimed and should take place in a maximum time of tP for normal programming or tFP for
fast programming. During this time, the status register and the RDY/BUSY pin will indicate that the part is busy.
PAGE ERASE: The Page Erase command can be used to individually erase any page
in the main memory array allowing the Buffer to Main Memory Page Program to be utilized at a later time. To perform a page erase, an opcode of 81H must be loaded into the
device, followed by four address bytes comprised of 7 don’t care bits, 14 page address
bits (PA13 - PA0) that specify the page in the main memory to be erased and 11 don’t
care bits. When a low-to-high transition occurs on the CS pin, the part will erase the
selected page (the erased state is a logical 1). The erase operation is internally selftimed and should take place in a maximum time of tPE. During this time, the status register and the RDY/BUSY pin will indicate that the part is busy.
BLOCK ERASE: A block of eight pages can be erased at one time. This command is
useful when large amounts of data has to be written into the device. This will avoid using
multiple Page Erase Commands. To perform a block erase, an opcode of 50H must be
loaded into the device, followed by four address bytes comprised of 7 don’t care bits, 11
page address bits (PA13 -PA3) and 14 don’t care bits. The 11 page address bits are
used to specify which block of eight pages is to be erased. When a low-to-high transition
occurs on the CS pin, the part will erase the selected block of eight pages. The erase
operation is internally self-timed and should take place in a maximum time of tBE. During
this time, the status register and the RDY/BUSY pin will indicate that the part is busy.
5
2472C–DFLSH–11/03
Block Erase Addressing
PA13
PA12
PA11
PA10
PA9
PA8
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
Block
0
0
0
0
0
0
0
0
0
0
0
X
X
X
0
0
0
0
0
0
0
0
0
0
0
1
X
X
X
1
0
0
0
0
0
0
0
0
0
1
0
X
X
X
2
0
0
0
0
0
0
0
0
0
1
1
X
X
X
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
0
0
X
X
X
2044
1
1
1
1
1
1
1
1
1
0
1
X
X
X
2045
1
1
1
1
1
1
1
1
1
1
0
X
X
X
2046
1
1
1
1
1
1
1
1
1
1
1
X
X
X
2047
Additional Commands
MAIN MEMORY PAGE TO BUFFER TRANSFER: A page of data can be transferred
from the main memory to either buffer 1 or buffer 2. To start the operation, a 1-byte
opcode, 53H for buffer 1 and 55H for buffer 2, must be clocked into the device, followed
by four address bytes comprised of 7 don’t care bits, 14 page address bits (PA13- PA0),
which specify the page in main memory that is to be transferred, and 11 don’t care bits.
The CS pin must be low while toggling the SCK/CLK pin to load the opcode and the
address bytes from the input pins (SI or I/O7 - I/O0). The transfer of the page of data
from the main memory to the buffer will begin when the CS pin transitions from a low to
a high state. During the transfer of a page of data (tXFR), the status register can be read
or the RDY/BUSY can be monitored to determine whether the transfer has been
completed.
MAIN MEMORY PAGE TO BUFFER COMPARE: A page of data in main memory can
be compared to the data in buffer 1 or buffer 2. To initiate the operation, a 1-byte
opcode, 60H for buffer 1 and 61H for buffer 2, must be clocked into the device, followed
by four address bytes consisting of 7 don’t care bits, 14 page address bits (PA13 - PA0)
that specify the page in the main memory that is to be compared to the buffer, and 11
don’t care bits. The CS pin must be low while toggling the SCK/CLK pin to load the
opcode and the address bytes from the input pins (SI or I/O7 - I/O0). On the low-to-high
transition of the CS pin, the 1056 bytes in the selected main memory page will be compared with the 1056 bytes in buffer 1 or buffer 2. During this time (tXFR), the status
register and the RDY/BUSY pin will indicate that the part is busy. On completion of the
compare operation, bit 6 of the status register is updated with the result of the compare.
STATUS REGISTER READ: The status register can be used to determine the device’s
ready/busy status, the result of a Main Memory Page to Buffer Compare operation, or
the device density. To read the status register, an opcode must be loaded into the
device. After the opcode and optional dummy byte(s) is clocked in, the 1-byte status
register will be clocked out on the output pins (SO or I/O7 - I/O0), starting with the next
clock cycle. In case of serial interface, opcode D7H is followed with an optional dummy
byte (8 clocks). For Serial applications over 25 MHz, opcode must be always followed
with a dummy byte. In case of applications with 8-bit interface, opcode D7H and two
dummy clock cycles should be used. When using the serial interface, the data in the status register, starting with the MSB (bit 7), will be clocked out on the SO pin during the
next eight clock cycles.
6
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
The six most-significant bits of the status register will contain device information, while
the remaining two least-significant bits are reserved for future use and will have undefined values. After the one byte of the status register has been clocked out, the
sequence will repeat itself (as long as CS remains low and SCK/CLK is being toggled).
The data in the status register is constantly updated, so each repeating sequence will
output new data.
Ready/busy status is indicated using bit 7 of the status register. If bit 7 is a 1, then the
device is not busy and is ready to accept the next command. If bit 7 is a 0, then the
device is in a busy state. Since the data in the status register is constantly updated, the
user must toggle SCK/CLK pin to check the ready/busy status. There are five operations
that can cause the device to be in a busy state: Main Memory Page to Buffer Transfer,
Main Memory Page to Buffer Compare, Buffer to Main Memory Page Program, Page
Erase and Block Erase.
The result of the most recent Main Memory Page to Buffer Compare operation is indicated using bit 6 of the status register. If bit 6 is a 0, then the data in the main memory
page matches the data in the buffer. If bit 6 is a 1, then at least one bit of the data in the
main memory page does not match the data in the buffer.
The device density is indicated using bits 5, 4, 3, and 2 of the status register. For the
AT45DB1282, the four bits are 0, 1, 0, 0. The decimal value of these four binary bits
does not equate to the device density; the four bits represent a combinational code
relating to differing densities of DataFlash devices.
Status Register Format
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RDY/BUSY
COMP
0
1
0
0
X
X
7
2472C–DFLSH–11/03
Manufacturer and Device ID Read
This instruction allows the user to read the Manufacturer ID, Device ID, and Extended Device Information. This mode is only
offered via the serial interface with clock frequencies up to 25 MHz. A 1-byte opcode, 9FH, must be clocked into the device
while the CS pin is low. After the opcode is clocked in, the Manufacturer ID, 2 bytes of Device ID and Extended Device Information will be clocked out on the SO pin. The fourth byte of the sequence output is the Extended Device Information String
Length byte. This byte is used to signify how many bytes of Extended Device Information will be output.
Manufacturer and Device ID Information
Byte 1 – Manufacturer ID
JEDEC Assigned Code
Hex
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1FH
0
0
0
1
1
1
1
1
Manufacturer ID
1FH = Atmel
Byte 2 – Device ID (Part 1)
Family Code
Density Code
Hex
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Family Code
29H
0
0
1
0
1
0
0
1
Density Code
001 = DataFlash
01001 = 128-Mbit
Byte 3 – Device ID (Part 2)
MLC Code
Product Version Code
Hex
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
20H
0
0
1
0
0
0
0
0
MLC Code
001 = 2-Bit/Cell Technology
Product Version
00000 = Initial Version
Byte Count
00H = 0 Bytes of Information
Byte 4 – Extended Device Information String Length
Byte Count
Hex
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
00H
0
0
0
0
0
0
0
0
CS
SI
9FH
Opcode
SO
1FH
29H
20H
00H
Data
Data
Manufacturer ID
Byte n
Device ID
Byte 1
Device ID
Byte 2
Extended
Device
Information
String Length
Extended
Device
Information
Byte x
Extended
Device
Information
Byte x + 1
This information
would only be output
if the Extended Device
Information String Length
value was something
other than 00H.
Each transition
represents 8 bits
Note:
8
Based on JEDEC publication 106 (JEP106), Manufacturer ID data can be comprised of any number of bytes. Some manufacturers may have
Manufacturer ID codes that are two, three or even four bytes long with the first byte(s) in the sequence being 7FH. A system should detect code
7FH as a “Continuation Code” and continue to read Manufacturer ID bytes. The first non-7FH byte would signify the last byte of Manufacturer ID
data. For Atmel (and some other manufacturers), the Manufacturer ID data is comprised of only one byte.
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Security Register
The AT45DB1282 contains a specialized register that can be used for security purposes
in system design. The Security Register is a unique 128-byte register that is divided into
two portions. The first 64 bytes (byte 0 to byte 63) of this register are allocated as a onetime user programmable space. Once these 64 bytes have been programmed, they
should not be reprogrammed. The remaining 64 bytes of this register (byte 64 to byte
127) are factory programmed by Atmel and will contain a unique number for each
device. The factory programmed data is fixed and cannot be changed.
The Security Register can be read by clocking in opcode 77H to the device followed by
four address bytes (which are comprised of 21 don’t care bits plus 11 byte address bits)
and a series of don’t care clock cycles (24 if using the serial interface and 19 if using the
8-bit interface). The Security Register Read can be terminated by asserting CS low to
high after the 128-byte security register has been read out. The continuation of clocking
past that will result in indeterminate data on the output. See the opcode table on page
13 for this mode.
To program the first 64 bytes of the Security Register, a two step sequence must be
used. The first step requires that the user loads the desired data into Buffer 1 by using
the Buffer 1 Write operation (opcode 84H – see Buffer Write description). The user
should specify the starting buffer address as location zero and should write a full
64 bytes of information into the buffer. Otherwise, the first 64 bytes of the buffer may
contain data that was previously stored in the buffer. It is not necessary to fill the remaining 992 bytes (byte locations 64 through 1055) of the buffer with data. After the Buffer 1
Write operation has been completed, the Security Register can be subsequently programmed by reselecting the device and clocking in opcode 9AH into the device followed
by four don’t care bytes (32 clock cycles if using the serial interface and four clock
cycles if using the 8-bit interface). After the final don’t care clock cycle has been
completed, a low-to-high transition on the CS pin will cause the device to initiate an
internally self-timed program operation in which the contents of Buffer 1 will be programmed into the Security Register. Only the first 64 bytes of data in Buffer 1 will be
programmed into the Security Register; the remaining 992 bytes of the buffer will be
ignored. The Security Register program operation should take place in a maximum time
of tP.
Operation Mode
Summary
The modes described can be separated into two groups – modes that make use of the
Flash memory array (Group A) and modes that do not make use of the Flash memory
array (Group B).
Group A modes consist of:
1. Main Memory Page Read
2. Continuous Array Read
3. Main Memory Page to Buffer 1 (or 2) Transfer
4. Main Memory Page to Buffer 1 (or 2) Compare
5. Buffer 1 (or 2) to Main Memory Page Program
6. Page Erase
7. Block Erase
Group B modes consist of:
1. Buffer 1 (or 2) Read
2. Buffer 1 (or 2) Write
3. Status Register Read
9
2472C–DFLSH–11/03
If a Group A mode is in progress (not fully completed), then another mode in Group A
should not be started. However, during this time in which a Group A mode is in
progress, modes in Group B can be started, except the first two Group A commands
(Memory Array Read Commands).
This gives the DataFlash the ability to virtually accommodate a continuous data stream.
While data is being programmed into main memory from buffer 1, data can be loaded
into buffer 2 (or vice versa). See application note AN-4 (“Using Atmel’s Serial
DataFlash”) for more details.
Pin Descriptions
SERIAL/8-BIT INTERFACE CONTROL (SER/BYTE): The DataFlash may be configured to utilize either its serial port or 8-bit port through the use of the serial/8-bit control
pin (SER/BYTE). When the SER/BYTE pin is held high, the serial port (SI and SO) of
the DataFlash will be used for all data transfers, and the 8-bit port (I/O7 - I/O0) will be in
a high impedance state. Any data presented on the 8-bit port while SER/BYTE is held
high will be ignored. When the SER/BYTE is held low, the 8-bit port will be used for all
data transfers, and the SO pin of the serial port will be in a high impedance state. While
SER/BYTE is low, any data presented on the SI pin will be ignored. Switching between
the serial port and 8-bit port should only be done while the CS pin is high and the device
is not busy in an internally self-timed operation.
The SER/BYTE pin is internally pulled high; therefore, if the 8-bit port is never to be
used, then connection of the SER/BYTE pin is not necessary. In addition, if the
SER/BYTE pin is not connected or if the SER/BYTE pin is always driven high externally,
then the 8-bit input/output pins (I/O7-I/O0), the VCCP pin, and the GNDP pin should be
treated as “don’t connects”.
SERIAL INPUT (SI): The SI pin is an input-only pin and is used to shift data serially into
the device. The SI pin is used for all data input, including opcodes and address
sequences. If the SER/BYTE pin is always driven low, then the SI pin should be a “don’t
connect”.
SERIAL OUTPUT (SO): The SO pin is an output-only pin and is used to shift data serially out from the device. If the SER/BYTE pin is always driven low, then the SO pin
should be a “don’t connect”.
8-BIT INPUT/OUTPUT (I/O7-I/O0): The I/O7-I/O0 pins are bidirectional and used to
clock data into and out of the device. The I/O7-I/O0 pins are used for all data input,
including opcodes and address sequences. The use of these pins is optional, and the
pins should be treated as “don’t connects” if the SER/BYTE pin is not connected or if the
SER/BYTE pin is always driven high externally.
SERIAL CLOCK/CLOCK (SCK/CLK): The SCK and CLK pins are input-only pins and
are used to control the flow of data to and from the DataFlash. The SCK and CLK pins
are used for serial and 8-bit interface respectively. Data is always clocked into the
device on the rising edge of SCK/CLK and clocked out of the device on the falling edge
of SCK/CLK.
CHIP SELECT (CS): The DataFlash is selected when the CS pin is low. When the
device is not selected, data will not be accepted on the input pins (SI or I/O7-I/O0), and
the output pins (SO or I/O7-I/O0) will remain in a high impedance state. A high-to-low
transition on the CS pin is required to start an operation, and a low-to-high transition on
the CS pin is required to end an operation.
HARDWARE PAGE WRITE PROTECT: If the WP pin is held low, the first 256 pages
(sectors 0 and 1) of the main memory cannot be reprogrammed. The only way to reprogram the first 256 pages is to first drive the protect pin high and then use the program
10
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
commands previously mentioned. If this pin and feature are not utilized it is recommended that the WP pin be driven high externally.
RESET: A low state on the reset pin (RESET) will terminate the operation in progress
and reset the internal state machine to an idle state. The device will remain in the reset
condition as long as a low level is present on the RESET pin. Normal operation can
resume once the RESET pin is brought back to a high level.
The device incorporates an internal power-on reset circuit, so there are no restrictions
on the RESET pin during power-on sequences. If this pin and feature are not utilized it is
recommended that the RESET pin be driven high externally.
READY/BUSY: This open drain output pin will be driven low when the device is busy in
an internally self-timed operation. This pin, which is normally in a high state (through
an external pull-up resistor), will be pulled low during programming/erase operations,
compare operations, and page-to-buffer transfers.
The busy status indicates that the Flash memory array and one of the buffers cannot be
accessed; read and write operations to the other buffer can still be performed.
8-BIT PORT SUPPLY VOLTAGE (VCCP AND GNDP): The VCCP and GNDP pins are
used to supply power for the 8-bit input/output pins (I/O7-I/O0). The VCCP and GNDP
pins need to be used if the 8-bit port is to be utilized; however, these pins should be
treated as “don’t connects” if the SER/BYTE pin is not connected or if the SER/BYTE pin
is always driven high externally.
Power-on/Reset State
When power is first applied to the device, or when recovering from a reset condition, the
device will default to Mode 3. In addition, the output pins (SO or I/O7 - I/O0) will be in a
high impedance state, and a high-to-low transition on the CS pin will be required to start
a valid instruction. The mode (Mode 3 or Mode 0) will be automatically selected on every
falling edge of CS by sampling the inactive clock state. After power is applied and VCC is
at the minimum datasheet value, the system should wait 20 ms before an operational
mode is started.
System
Considerations
The RapidS serial interface is controlled by the serial clock SCK, serial input SI and chip
select CS pins. The sequential 8-bit Rapid8 is controlled by the clock CLK, 8 I/Os and
chip select CS pins. These signals must rise and fall monotonically and be free from
noise. Excessive noise or ringing on these pins can be misinterpreted as multiple edges
and cause improper operation of the device. The PC board traces must be kept to a
minimum distance or appropriately terminated to ensure proper operation. If necessary,
decoupling capacitors can be added on these pins to provide filtering against noise
glitches.
As system complexity continues to increase, voltage regulation is becoming more
important. A key element of any voltage regulation scheme is its current sourcing capability. Like all Flash memories, the peak current for DataFlash occur during the
programming and erase operation. The regulator needs to supply this peak current
requirement. An under specified regulator can cause current starvation. Besides
increasing system noise, current starvation during programming or erase can lead to
improper operation and possible data corruption.
11
2472C–DFLSH–11/03
Table 1. Read Commands
Command
Serial/8-bit
Opcode
Main Memory Page Read
Both
D2h
Continuous Array Read
Both
E8h
Buffer 1 Read
Serial
D4h
Buffer 2 Read
Serial
D6h
Buffer 1 Read
8-bit
54h
Buffer 2 Read
8-bit
56h
Serial/8-bit
Opcode
Buffer 1 Write
Both
84h
Buffer 2 Write
Both
87h
Buffer 1 to Main Memory Page Program
Both
88h
Buffer 1 to Main Memory Page Program,
Fast Program
Both
98h
Buffer 2 to Main Memory Page Program
Both
89h
Buffer 2 to Main Memory Page Program,
Fast Program
Both
99h
Page Erase
Both
81h
Block Erase
Both
50h
Serial/8-bit
Opcode
Main Memory Page to Buffer 1 Transfer
Both
53h
Main Memory Page to Buffer 2 Transfer
Both
55h
Main Memory Page to Buffer 1 Compare
Both
60h
Main Memory Page to Buffer 2 Compare
Both
61h
Status Register Read
Both
D7h
Serial
9Fh
Both
9Ah
Table 2. Program and Erase Commands
Command
Table 3. Additional Commands
Command
Manufacturer and Device ID Read
(1)
Security Register Program
Security Register Read
Both
77h
Note:
1. The Security Register Program command utilizes data stored in Buffer 1. Therefore,
this command must be used in conjunction with the Buffer 1 write command. See the
Security Register description for details.
12
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Table 4. Detailed Bit-level Addressing Sequence
BA0
BA1
BA2
BA3
BA4
BA5
BA6
BA7
BA8
BA9
Address Byte
BA10
PA0
PA1
PA2
PA3
PA4
PA5
PA6
Address Byte
PA7
PA8
PA10
PA9
PA11
Opcode
PA12
Opcode
Address Byte
PA13
Address Byte
Additional
Don’t Care
Bytes*
50h
0 1 0 1 0 0 0 0
x x x x x x x P
P P P P P P P P P P x x x x x x
x x x x x x x x
N/A
53h
0 1 0 1 0 0 1 1
x x x x x x x P
P P P P P P P P P P P P P x x x
x x x x x x x x
N/A
54h
0 1 0 1 0 1 0 0
x x x x x x x x
x x x x x x x x
55h
0 1 0 1 0 1 0 1
x x x x x x x P
P P P P P P P P P P P P P x x x
56h
0 1 0 1 0 1 1 0
x x x x x x x x
x x x x x x x x
60h
0 1 1 0 0 0 0 0
x x x x x x x P
P P P P P P P P P P P P P x x x
x x x x x x x x
N/A
61h
0 1 1 0 0 0 0 1
x x x x x x x P
P P P P P P P P P P P P P x x x
x x x x x x x x
N/A
77h
0 1 1 1 0 1 1 1
x x x x x x x x
x x x x x x x x
81h
1 0 0 0 0 0 0 1
x x x x x x x P
P P P P P P P P P P P P P x x x
84h
1 0 0 0 0 1 0 0
x x x x x x x x
87h
1 0 0 0 0 1 1 1
88h
x x x x x B B B B B B B B B B B
x x x x x x x x
x x x x x B B B B B B B B B B B
x x x x x B B B B B B B B B B B
2*
N/A
2*
3 or 19*
x x x x x x x x
N/A
x x x x x x x x
x x x x x B B B B B B B B B B B
N/A
x x x x x x x x
x x x x x x x x
x x x x x B B B B B B B B B B B
N/A
1 0 0 0 1 0 0 0
x x x x x x x P
P P P P P P P P P P P P P x x x
x x x x x x x x
N/A
89h
1 0 0 0 1 0 0 1
x x x x x x x P
P P P P P P P P P P P P P x x x
x x x x x x x x
N/A
98h
1 0 0 1 1 0 0 0
x x x x x x x P
P P P P P P P P P P P P P x x x
x x x x x x x x
N/A
99h
1 0 0 1 1 0 0 1
x x x x x x x P
P P P P P P P P P P P P P x x x
x x x x x x x x
N/A
9Ah
1 0 0 1 1 0 1 0
x x x x x x x x
x x x x x x x x
x x x x x x x x
x x x x x x x x
N/A
9Fh
1 0 0 1 1 1 1 1
N/A
N/A
N/A
N/A
N/A
D2h
1 1 0 1 0 0 1 0
x x x x x x x P
P P P P P P P P P P P P P B B B B B B B B B B B
3 or 19*
D4h
1 1 0 1 0 1 0 0
x x x x x x x x
x x x x x x x x
x x x x x B B B B B B B B B B B
1
D6h
1 1 0 1 0 1 1 0
x x x x x x x x
x x x x x x x x
x x x x x B B B B B B B B B B B
1
D7h
1 1 0 1 0 1 1 1
N/A
N/A
N/A
1/0 or 1*
E8h
1 1 1 0 1 0 0 0
x x x x x x x P
P P P P P P P P P P P P P B B B B B B B B B B B
Notes:
N/A
3 or 19*
P = Page Address Bit
B = Byte/Buffer Address Bit
x = Don’t Care
*The number with (*) is for 8-bit interface.
13
2472C–DFLSH–11/03
Absolute Maximum Ratings*
Temperature under Bias ................................ -55°C to +125°C
*NOTICE:
Storage Temperature ..................................... -65°C to +150°C
All Input Voltages
(including NC Pins)
with Respect to Ground ...................................-0.6V to +6.25V
All Output Voltages
with Respect to Ground .............................-0.6V to VCC + 0.6V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
DC and AC Operating Range
AT45DB1282
Com.
0°C to 70°C
Operating Temperature (Case)
Ind.
VCC Power Supply
Note:
-40°C to 85°C
(1)
2.7V to 3.6V
1. After power is applied and VCC is at the minimum specified datasheet value, the system should wait 20 ms before an operational mode is started.
DC Characteristics
Symbol
Parameter
Condition
ISB
Standby Current
ICC1(1)
Typ
Max
Units
CS, RESET, WP = VIH, all
inputs at CMOS levels
5
15
µA
Active Current, Read
Operation, Serial Interface
f = 20 MHz; IOUT = 0 mA;
VCC = 3.6V
10
20
mA
ICC2(2)
Active Current, Read
Operation, 8-bit Interface
f = 10 MHz; IOUT = 0 mA;
VCC = 3.6V
12
20
mA
ICC3
Active Current, Program
Operation, Page Program
VCC = 3.6V
50
mA
ICC4
Active Current, Program
Operation, Fast Page Program
VCC = 3.6V
65
mA
ICC5
Active Current, Page Erase
Operation
VCC = 3.6V
50
mA
ICC6
Active Current, Block Erase
Operation
VCC = 3.6V
50
mA
ILI
Input Load Current
VIN = CMOS levels
1
µA
ILO
Output Leakage Current
VI/O = CMOS levels
1
µA
VIL
Input Low Voltage
VCC x 0.3
V
VIH
Input High Voltage
VOL
Output Low Voltage
IOL = 1.6 mA; VCC = 2.7V
Output High Voltage
IOH = -100 µA
VOH
Notes:
14
Min
VCC x 0.7
V
0.4
VCC - 0.2V
V
V
1. ICC1 during a buffer read is 25 mA maximum.
2. ICC2 during a buffer read is 25 mA maximum.
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
AC Characteristics – RapidS Serial Interface
Symbol
Parameter
fSCK
Min
Typ
Max
Units
SCK Frequency
40
MHz
fCAR
SCK Frequency for Continuous Array Read
40
MHz
tWH
SCK High Time
9
ns
tWL
SCK Low Time
9
ns
tCS
Minimum CS High Time
250
ns
tCSS
CS Setup Time
250
ns
tCSH
CS Hold Time
250
ns
tCSB
CS High to RDY/BUSY Low
tSU
Data In Setup Time
5
ns
tH
Data In Hold Time
7
ns
tHO
Output Hold Time
2
ns
tDIS
Output Disable Time
10
ns
tV
Output Valid
10
ns
tXFR
Page to Buffer Transfer/Compare Time
500
µs
tP
Page Programming Time
50
ms
tFP
Fast Page Programming Time
15
ms
tPE
Page Erase Time
25
ms
tBE
Block Erase Time
50
ms
tRST
RESET Pulse Width
tREC
RESET Recovery Time
150
10
ns
µs
1
µs
15
2472C–DFLSH–11/03
AC Characteristics – Rapid8 8-bit Interface
Symbol
Parameter
fSCK1
Min
Typ
Max
Units
CLK Frequency
20
MHz
fCAR1
CLK Frequency for Continuous Array Read
20
MHz
tWH
CLK High Time
16
ns
tWL
CLK Low Time
16
ns
tCS
Minimum CS High Time
250
ns
tCSS
CS Setup Time
250
ns
tCSH
CS Hold Time
250
ns
tCSB
CS High to RDY/BUSY Low
tSU
Data In Setup Time
10
ns
tH
Data In Hold Time
10
ns
tHO
Output Hold Time
3
ns
tDIS
Output Disable Time
15
ns
tV
Output Valid
15
ns
tXFR
Page to Buffer Transfer/Compare Time
500
µs
tP
Page Programming Time
50
ms
tFP
Fast Page Programming Time
15
ms
tPE
Page Erase Time
25
ms
tBE
Block Erase Time
50
ms
tRST
RESET Pulse Width
tREC
RESET Recovery Time
150
10
ns
µs
1
µs
Input Test Waveforms and Measurement Levels
AC
DRIVING
LEVELS
2.4V
1.5V
0.45V
tR, tF < 2 ns (10% to 90%)
AC
MEASUREMENT
LEVEL
Output Test Load
DEVICE
UNDER
TEST
30 pF
16
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
AC Waveforms
Six different timing waveforms are shown below. Waveform 1 shows the SCK/CLK signal being low when CS makes a high-to-low transition, and waveform 2 shows the
SCK/CLK signal being high when CS makes a high-to-low transition. In both cases, output SO becomes valid while the SCK/CLK signal is still low (SCK/CLK low time is
specified as tWL). Timing waveforms 1 and 2 conform to RapidS serial interface but for
frequencies up to 33 MHz. Waveforms 1 and 2 are compatible with SPI Mode 0 and SPI
Mode 3, respectively.
Waveform 3 and waveform 4 illustrate general timing diagram for RapidS serial interface. These are similar to waveform 1 and waveform 2, except that output SO is not
restricted to become valid during the tWL period. These timing waveforms are valid over
the full frequency range (maximum frequency = 40 MHz) of the RapidS serial case.
Waveform 5 and waveform 6 are for 8-bit Rapid8 interface over the full frequency range
of operation (maximum frequency = 20 MHz).
Waveform 1 – SPI Mode 0 Compatible (for Frequencies up to 33 MHz)
tCS
CS
tWH
tCSS
tWL
tCSH
SCK/CLK
tHO
tV
SO
HIGH IMPEDANCE
VALID OUT
tSU
tDIS
HIGH IMPEDANCE
tH
VALID IN
SI
Waveform 2 – SPI Mode 3 Compatible (for Frequencies up to 33 MHz)
tCS
CS
tCSS
tWL
tWH
tCSH
SCK/CLK
tV
SO
HIGH Z
tHO
VALID OUT
tSU
SI
tDIS
HIGH IMPEDANCE
tH
VALID IN
17
2472C–DFLSH–11/03
Waveform 3 – RapidS Mode 0 (for all Frequencies)
tCS
CS
tWH
tCSS
tWL
tCSH
SCK/CLK
tHO
tV
SO
HIGH IMPEDANCE
tDIS
HIGH IMPEDANCE
VALID OUT
tSU
tH
VALID IN
SI
Waveform 4 – RapidS Mode 3 (for all Frequencies)
tCS
CS
tCSS
tWL
tWH
tCSH
SCK/CLK
tV
SO
tHO
HIGH Z
tDIS
HIGH IMPEDANCE
VALID OUT
tSU
tH
VALID IN
SI
Waveform 5 – Rapid8 Mode 0 (FMAX = 20 MHz)
tCS
CS
tWH
tCSS
tWL
tCSH
SCK/CLK
tHO
tV
I/O7 - I/O0
(OUTPUT)
HIGH IMPEDANCE
VALID OUT
tSU
tDIS
HIGH IMPEDANCE
tH
VALID IN
I/O7 - I/O0
(INPUT)
Waveform 6 – Rapid8 Mode 3 (FMAX = 20 MHz)
tCS
CS
tCSS
tWL
tWH
tCSH
SCK/CLK
tV
I/O7 - I/O0
(OUTPUT)
HIGH Z
I/O7 - I/O0
(INPUT)
18
tHO
VALID OUT
tSU
tDIS
HIGH IMPEDANCE
tH
VALID IN
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Reset Timing
CS
tREC
tCSS
SCK/CLK
tRST
RESET
HIGH IMPEDANCE
HIGH IMPEDANCE
SO or I/O7 - I/O0
(OUTPUT)
SI or I/O7 - I/O0
(INPUT)
Note:
The CS signal should be in the high state before the RESET signal is deasserted.
Command Sequence for Read/Write Operations
(Except Status Register Read, Manufacturer and Device ID Read)
SI or I/O7 - I/O0
(INPUT)
MSB
CMD
8 bits
8 bits
XXXX XXXX
XXXX XXXX
7 Bits Don't
Care
8 bits
8 bits
XXXX XXXX
Page Address
(PA13 - PA0)
XXXX XXXX
LSB
Byte/Buffer Address
(BA10 - BA0/BFA10 - BFA0)
Write Operations
The following block diagram and waveforms illustrate the various write sequences available.
FLASH MEMORY ARRAY
PAGE (1056 BYTES)
BUFFER 1 TO
MAIN MEMORY
PAGE PROGRAM
BUFFER 2 TO
MAIN MEMORY
PAGE PROGRAM
BUFFER 1 (1056 BYTES)
BUFFER 2 (1056 BYTES)
BUFFER 2
WRITE
BUFFER 1
WRITE
I/O INTERFACE
SI
I/O7 - I/O0
19
2472C–DFLSH–11/03
Buffer Write
· Completes writing into selected buffer
CS
SI or I/O7 - I/O0
(INPUT)
CMD
X
X
n
BFA7-0
X···X, BFA10-8
n+1
Last Byte
Buffer to Main Memory Page Program (Data from Buffer Programmed into Flash Page)
Starts self-timed erase/program operation
CS
SI or I/O7 - I/O0
CMD
XXXXXXX PA13
PA12-5
PA4-0, XXX
X···X
(INPUT)
n = 1st byte
n+1 = 2nd byte
Each transition
represents 8 bits
Read Operations
The following block diagram and waveforms illustrate the various read sequences available.
FLASH MEMORY ARRAY
PAGE (1056 BYTES)
MAIN MEMORY
PAGE TO
BUFFER 2
MAIN MEMORY
PAGE TO
BUFFER 1
BUFFER 1 (1056 BYTES)
BUFFER 1
READ
BUFFER 2 (1056 BYTES)
MAIN MEMORY
PAGE READ
BUFFER 2
READ
I/O INTERFACE
SO
20
I/O7 - I/O0
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Main Memory Page Read
CS
SI or I/O7 - I/O0
(INPUT)
CMD
xxx...PA13
PA4-0, BA10-8
PA12-5
BA7-0
X
X
24 Cycles for Serial
19 Cycles for Parallel
SO or I/O7 - I/O0
(OUTPUT)
n
n+1
Main Memory Page to Buffer Transfer (Data from Flash Page Read into Buffer)
Starts reading page data into buffer
CS
SI or I/O7 - I/O0
(INPUT)
CMD
XX...PA13
X
PA4-0, XXX
PA12-5
SO or I/O7 - I/O0
(OUTPUT)
Buffer Read
CS
I/O7-I/O0
(INPUT)
CMD
X
X
X···X, BFA10-8
ADDR
I/O7-I/O0
(OUTPUT)
Each transition
represents 8 bits
BFA7-0
X
ADDR 1 Dummy Byte (Serial)
2 Dummy Bytes (Parallel)
n
n+1
n = 1st byte read
n+1 = 2nd byte read
21
2472C–DFLSH–11/03
Detailed Bit-level Read Timing – RapidS Serial Interface Mode 0
Continuous Array Read (Opcode: E8H)
CS
SCK
1
2
62
63
64
1
1
X
X
X
65
66
67
tSU
SI
tV
HIGH IMPEDANCE
SO
DATA OUT
D7
D6
D5
D2
D1
LSB
MSB
D0
D7
BIT 8,447
OF
PAGE n
D6
D5
BIT 0
OF
PAGE n+1
Main Memory Page Read (Opcode: D2H)
CS
SCK
1
2
3
4
5
60
61
62
63
64
0
X
X
X
X
X
65
66
67
tSU
COMMAND OPCODE
SI
1
1
0
1
tV
SO
22
HIGH IMPEDANCE
DATA OUT
D7
MSB
D6
D5
D4
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Detailed Bit-level Read Timing – RapidS Serial Interface Mode 0 (Continued)
Buffer Read (Opcode: D4H or D6H)
CS
SCK
1
2
3
4
5
44
45
46
47
48
0
X
X
X
X
X
49
50
51
tSU
COMMAND OPCODE
SI
1
1
1
0
tV
DATA OUT
HIGH IMPEDANCE
SO
D7
D6
D4
D5
MSB
Status Register Read (Opcode: D7H)
CS
SCK
1
2
1
1
3
tSU
SI
4
5
6
7
8
1
1
9
10
11
12
15
16
COMMAND OPCODE
0
1
0
1
tV
STATUS REGISTER OUTPUT
tV
HIGH IMPEDANCE
SO
D7
MSB
D6
D5
D4
D1
D0
LSB
D7
MSB
DON’T CARE FOR
FREQ. OVER 25 MHz
Manufacturer and Device ID Read (Opcode: 9FH)
CS
SCK
1
2
3
1
0-
4
5
6
7
8
1
1
9
10
11
0
MSB
0
0
12
16
17
tSU
COMMAND OPCODE
SI
0
1
1
1
tV
SO
HIGH IMPEDANCE
PRODUCT ID OUTPUT
1
1
LSB
0
MSB
0
23
2472C–DFLSH–11/03
Detailed Bit-level Read Timing – RapidS Serial Interface Mode 3
Continuous Array Read (Opcode: E8H)
CS
SCK
1
2
63
64
65
66
67
tSU
SI
1
1
X
X
X
tV
HIGH IMPEDANCE
SO
DATA OUT
D7
D6
D5
D2
D1
LSB
MSB
D0
D7
BIT 8,447
OF
PAGE n
D6
D5
BIT 0
OF
PAGE n+1
Main Memory Page Read (Opcode: D2H)
CS
SCK
1
2
3
4
5
61
62
63
64
65
66
67
68
tSU
COMMAND OPCODE
SI
1
1
0
1
0
X
X
X
X
X
tV
SO
24
HIGH IMPEDANCE
DATA OUT
D7
MSB
D6
D5
D4
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Detailed Bit-level Read Timing – RapidS Serial Interface Mode 3 (Continued)
Buffer Read (Opcode: D4H or D6H)
CS
SCK
1
2
3
4
5
45
46
47
48
49
50
52
51
tSU
COMMAND OPCODE
SI
1
1
1
0
0
X
X
X
X
X
tV
DATA OUT
HIGH IMPEDANCE
SO
D7
MSB
D6
D5
D4
17
18
Status Register Read (Opcode: D7H)
CS
SCK
1
2
3
tSU
4
5
7
6
8
9
10
11
12
COMMAND OPCODE
SI
1
1
1
0
0
1
1
1
tV
STATUS REGISTER OUTPUT
tV
HIGH IMPEDANCE
SO
D7
MSB
D6
D5
D4
D0
LSB
D7
MSB
D6
DON’T CARE FOR
FREQ. OVER 25 MHz
Manufacturer and Device ID Read (Opcode: 9FH)
CS
SCK
1
2
3
4
5
6
7
8
9
10
11
12
17
18
tSU
COMMAND OPCODE
SI
1
0
0
1
1
1
1
1
tV
SO
HIGH IMPEDANCE
PRODUCT ID OUTPUT
0
MSB
0
0
1
1
LSB
0
MSB
0
25
2472C–DFLSH–11/03
Detailed 8-bit Read Timing – Rapid8 Mode 0
Continuous Array Read (Opcode: E8H)
CS
CLK
1
2
22
23
24
CMD
ADDR
X
X
X
25
26
27
tSU
I/O7-I/O0
(INPUT)
tV
I/O7-I/O0
(OUTPUT)
HIGH IMPEDANCE
DATA OUT
DATA
DATA
DATA
DATA
DATA
DATA
DATA
BYTE 1055
OF
PAGE n
DATA
DATA
BYTE 0
OF
PAGE n+1
Main Memory Page Read (Opcode: D2H)
CS
CLK
1
2
3
4
5
20
21
22
23
24
ADDR
X
X
X
X
X
25
26
27
tSU
I/O7-I/O0
(INPUT)
COMMAND OPCODE
CMD
ADDR
ADDR
ADDR
tV
I/O7-I/O0
(OUTPUT)
26
HIGH IMPEDANCE
DATA OUT
DATA DATA DATA DATA
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Detailed 8-bit Timing – Rapid8 Mode 0 (Continued)
Buffer Read (Opcode: 54H or 56H)
CS
CLK
1
2
3
5
6
7
ADDR
X
X
4
8
tSU
COMMAND OPCODE
I/O7-I/O0
(INPUT)
CMD
X
ADDR
X
tV
DATA OUT
HIGH IMPEDANCE
I/O7-I/O0
(OUTPUT)
DATA DATA DATA
MSB
Status Register Read (Opcode: D7H)
CS
CLK
1
2
3
tSU
I/O7-I/O0
(INPUT)
CMD
tV
I/O7-I/O0
(OUTPUT)
HIGH IMPEDANCE
X
X
DATA DATA
DATA
STATUS
REGISTER OUTPUT
27
2472C–DFLSH–11/03
Detailed 8-bit Read Timing – Rapid8 Mode 3
Continuous Array Read (Opcode: E8H)
CS
CLK
1
2
23
24
25
26
27
tSU
I/O7-I/O0
(INPUT)
CMD ADDR
X
X
X
tV
HIGH IMPEDANCE
I/O7-I/O0
(OUTPUT)
DATA OUT
DATA DATA DATA
DATA DATA DATA DATA DATA DATA
BYTE 1055
OF
PAGE n
BYTE 0
OF
PAGE n+1
Main Memory Page Read (Opcode: D2H)
CS
CLK
1
2
3
4
5
21
22
23
24
25
26
27
28
tSU
I/07-I/O0
(INPUT)
COMMAND OPCODE
CMD
ADDR ADDR ADDR ADDR
X
X
X
X
X
tV
I/07-I/O0
(OUTPUT)
28
HIGH IMPEDANCE
DATA OUT
DATA DATA DATA DATA
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Detailed 8-bit Read Timing – Rapid8 Mode 3 (Continued)
Buffer Read (Opcode: 54H or 56H)
CS
CLK
1
2
3
4
5
6
7
8
9
10
tSU
I/O7-I/O0
(INPUT)
CMD
X
X
ADDR ADDR
X
X
tV
DATA OUT
HIGH IMPEDANCE
I/O7-I/O0
(OUTPUT)
DATA DATA DATA
Status Register Read (Opcode: D7H)
CS
CLK
1
2
3
tSU
I/O7-I/O0
(INPUT)
CMD
tV
I/O7-I/O0
(OUTPUT)
HIGH
IMPEDANCE
X
X
DATA
DATA
STATUS REGISTER
OUTPUT
29
2472C–DFLSH–11/03
Figure 1. Algorithm for Programming or Reprogramming of the Entire Array Sequentially
START
provide address
and data
BUFFER WRITE
(84h, 87h)
Page Erase
(81h)
BUFFER TO MAIN
MEMORY PAGE PROGRAM
(88h, 89h) or (98h, 99h)
END
Notes:
30
1. This type of algorithm is used for applications in which the entire array is programmed sequentially, filling the array page-bypage.
2. A page is written using a Buffer 1 or Buffer 2 Write operation followed by a Buffer (1 to 2) to Main Memory Page Program
operation (either regularly or in Fast Program).
3. The algorithm above shows the programming of a single page. The algorithm will be repeated sequentially for each page
within the entire array.
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Figure 2. Algorithm for Randomly Modifying Data
START
provide address of
page to modify
MAIN MEMORY PAGE
TO BUFFER TRANSFER
(53h, 55h)
If planning to modify multiple
bytes currently stored within
a page of the Flash array
BUFFER WRITE
(84h, 87h)
PAGE ERASE
(81h)
BUFFER TO MAIN
MEMORY PAGE PROGRAM
(88h, 89h) or (98h, 99h)
INCREMENT PAGE
(2)
ADDRESS POINTER
END
Notes:
1. To preserve data integrity, each page of a DataFlash sector must be updated/rewritten at least once within every 2,000
cumulative page erase/program operations.
2. A Page Address Pointer must be maintained to indicate which page is to be rewritten.
3. Other algorithms can be used to rewrite portions of the Flash array. Low-power applications may choose to wait until 2,000
cumulative page erase/program operations have accumulated before rewriting all pages of the sector. See application note
AN-4 (“Using Atmel’s Serial DataFlash”) for more details.
Sector Addressing
PA13
PA12
PA11
PA10
PA9
PA8
PA7
PA6
PA5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
X
X
X
0
0
0
0
0
1
X
X
X
0
0
0
0
1
0
X
X
X
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PA4
PA3
PA2 - PA0
Sector
0
0
X
0
X
X
X
1
X
X
X
2
X
X
X
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
0
0
X
X
X
X
X
X
61
1
1
1
1
0
1
X
X
X
X
X
X
62
1
1
1
1
1
0
X
X
X
X
X
X
63
1
1
1
1
1
1
X
X
X
X
X
X
64
31
2472C–DFLSH–11/03
Ordering Information
ICC (mA)
fSCK
(MHz)
Active
Standby
40(1)
20(1)
40(1)
Operation Range
Ordering Code
Package
0.015
AT45DB1282-TC
40T
Commercial
(0°C to 70°C)
20(1)
0.015
AT45DB1282-TI
40T
Industrial
(-40°C to 85°C)
40(1)
20(1)
0.015
AT45DB1282-CC
44C2
Commercial
(0°C to 70°C)
40(1)
20(1)
0.015
AT45DB1282-CI
44C2
Industrial
(-40°C to 85°C)
Note:
1. RapidS Serial Interface.
Package Type
40T
40-lead, (10 x 20 mm) Plastic Thin Small Outline Package, Type I (TSOP)
44C2
44-ball, (8 x 12 mm) Plastic Chip-size Ball Grid Array Package (CBGA)
32
AT45DB1282
2472C–DFLSH–11/03
AT45DB1282
Packaging Information
40T – TSOP
PIN 1
0º ~ 8º
c
Pin 1 Identifier
D1 D
L
b
e
L1
A2
E
A
GAGE PLANE
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
SYMBOL
Notes:
1. This package conforms to JEDEC reference MO-142, Variation CD.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side.
3. Lead coplanarity is 0.10 mm maximum.
NOTE
A2
0.95
1.00
1.05
D
19.80
20.00
20.20
D1
18.30
18.40
18.50
Note 2
E
9.90
10.00
10.10
Note 2
L
0.50
0.60
0.70
L1
0.25 BASIC
b
0.17
0.22
0.27
c
0.10
–
0.21
e
0.50 BASIC
10/18/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
40T, 40-lead (10 x 20 mm Package) Plastic Thin Small Outline
Package, Type I (TSOP)
DRAWING NO.
REV.
40T
B
33
2472C–DFLSH–11/03
44C2 – CBGA
0.12 C
D
C Seating Plane
Marked A1
Identifier
Side View
E
A1
Top View
2.00 REF
A
D1
5
4
A1 Ball Corner
2
3
1
A
e
B
C
COMMON DIMENSIONS
(Unit of Measure = mm)
D
E1
E
F
SYMBOL
MIN
NOM
MAX
G
A
–
–
1.20
A1
0.25
–
–
D
7.90
8.00
8.10
H
NOTE
J
2.00 REF
e
Øb
D1
E
4.00 TYP
11.90
E1
Bottom View
12.00
12.10
8.00 TYP
e
1.00 TYP
Øb
0.40 TYP
06/10/03
R
34
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44C2, 44-ball (5 x 9 Array), 8 x 12 x 1.2 mm Body, 0.4 mm Ball
Plastic Chip-scale Ball Grid Array Package (CBGA)
DRAWING NO.
44C2
REV.
A
AT45DB1282
2472C–DFLSH–11/03
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard
warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any
errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and
does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are
granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use
as critical components in life support devices or systems.
© Atmel Corporation 2003. All rights reserved. Atmel ® and combinations thereof, and DataFlash ® are the registered trademarks, and RapidS ™, Rapid8 ™ and e -STAC ™ are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.
Printed on recycled paper.
2472C–DFLSH–11/03
/xM