Features • 1.5 Gbps Bi-directional Transceiver – Compliant with Serial ATA Gen1 Revision 1.0a Specification • Low Power Operation – 75 mW per Channel Nominal • Key Blocks Include – Integrated OOB Processor – K28.5 COMMA Detection – Digital Clock and Data Recovery (CDR) with Digital Equalization – Spread Spectrum Clocking – Optional 8B/10B Encoder and Decoder • Parallel I/O – Synchronous 8-bit/10-bit Parallel Interface @ 150 MHz • Serial I/0 – Programmable Pre-emphasis – Programmable Swing Control – Passive Equalization in Receive Input Buffer – Support for Spread Spectrum Clocking – Integrated 100Ω Matched Differential Termination – AC and DC Coupling Support • Test Features – Far-end and Near-end Loopback Support – At Speed BIST – Scan Test of Physical Coding Sub-layer (PCS) 2-channel Serial ATA PHY AT78C5090 Summary Overview The AT78C5090 is a 2-channel SATA PHY supporting Gen 1 speeds of 1.5 Gbps. The IP has been designed based on the requirements stated in the Serial ATA Standard, Rev 1.0a, Jan 2003. On the transmit path, parallel data is registered, passed through a transmit FIFO to compensate for phase differences between the link and PHY clocks, 8B/10B encoded and then passed out via a high speed serializer using a spread spectrum clock. Builtin flexibility permits bypassing the encoding block in addition to optionally disabling the spread spectrum clocking. The user can control the transmit buffer output swing and pre-emphasis levels via direct input signals. On the receive path, the AT78C5090 performs the serial-to-parallel conversion, using a high bandwidth clock and data recovery (CDR) block. The recovered data is then passed through a comma alignment block and an optional 8B/10B decode block before being passed to the phyCtrl layer via a parallel interface. This interface is synchronous to the recovered clock. The PHY core has an out of band (OOB) processor. As specified by the Serial ATA standard, three out of band (OOB) signals are used/detected by the PHY, namely COMRESET, COMINIT, and COMWAKE. Each of these signals are indicated by a number of bursts of four ALIGN primitives followed by defined idle periods during which the differential voltage on the serial line is null. OOB signals are observed by detecting the temporal spacing between adjacent bursts of activity. Test functions including BIST, scan, parallel and serial loopback modes are configured and controlled by the use of direct input signals. Similarly, error/status bits are indicated through direct output signals such as bistErr. 3526AS–NETST–10/04 Note: This is a summary document. A complete document is available under NDA. For more information, please contact your local Atmel sales office. Block Diagram(1) t[7:0] tBC cD tBIMSB syncMode txClk txPreEmCtrl[2:0] txP Serializer Tx FIFO txSSCMode[2:0] rxSCCMode refClk dual, rate bist bistErr enDec lBEn[2:0] pOR, phyReset rxRefMode frcPhyRdy cfgHostMode gotCIOrR gotComWake phyRdy scanClk,scanEn scanResetL scanMode scanIn1,2 scanOut1,2 vizGroup[15:0] txM 8B/10B Encode BIST & Test Pattern Generator High Speed PLLs pllFilt pllBGap iDDQEn debugEnL debugSel[3:0] debugClk Control Block OOB Processor Analog Bias 8B/10B Decode Digital CDR anaViz txAmpCtrl[3:0] resRef VSSRESREF rxP rxM rDat2Link[10:0] phyRClk phyIntErr enCommaDet Note: 2 1. The block diagram only shows one channel. AT78C5090 3526AS–NETST–10/04 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2004. All rights reserved. Atmel ®, logo and combinations thereof, are registered trademarks, and Everywhere You AreSM is the trademark of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 3526AS–NETST–10/04