CY7C9689A TAXI™-compatible HOTLink® Transceiver Features ■ Second-generation HOTLink® technology ■ AMD™ AM7968/7969 TAXIchip™-compatible ■ 8-bit 4B/5B or 10-bit 5B/6B NRZI encoded data transport ■ 10-bit or 12-bit NRZI pre-encoded (bypass) data transport ■ Synchronous TTL parallel interface ■ Embedded/bypassable 256-character Transmit and Receive FIFOs ■ 50- to 200-MBaud serial signaling rate ■ Internal phase-locked loops (PLLs) with no external PLL components ■ Dual differential PECL-compatible serial inputs and outputs ■ Compatible with fiber-optic modules and copper cables ■ Built-in self-test (BIST) for link testing ■ Link Quality Indicator ■ Single +5.0 V ±10%supply ■ 100-pin TQFP ■ Pb-free package option available Functional Description The CY7C9689A HOTLink Transceiver is a point-to-point communications building block allowing the transfer of data over high-speed serial links (optical fiber, balanced, and unbalanced copper transmission lines) at speeds ranging between 50 and 200 MBaud. The transmit section accepts parallel data of selectable widths and converts it to serial data, while the receiver section accepts serial data and converts it to parallel data of selectable widths. Figure 1 illustrates typical connections between two independent host systems and corresponding CY7C9689A parts. The CY7C9689A provides enhanced technology, increased functionality, a higher level of integration, higher data rates, and lower power dissipation over the AMD AM7968/7969 TAXIchip products. The transmit section of the CY7C9689A HOTLink can be configured to accept either 8- or 10-bit data characters on each clock cycle, and stores the parallel data into an internal Cypress Semiconductor Corporation Document Number: 38-02020 Rev. *H • synchronous Transmit FIFO. Data is read from the Transmit FIFO and is encoded using embedded 4B/5B or 5B/6B encoders to improve its serial transmission characteristics. These encoded characters are then serialized, converted to NRZI, and output from two PECL-compatible differential transmission line drivers at a bit-rate of either 10 or 20 times the input reference clock in 8-bit (or 10-bit bypass) mode, or 12 or 24 times the reference clock in 10-bit (or 12-bit bypass) mode. The receive section of the CY7C9689A HOTLink accepts a serial bit-stream from one of two PECL compatible differential line receivers and, using a completely integrated PLL clock synchronizer, recovers the timing information necessary for data reconstruction. The recovered bit stream is converted from NRZI to NRZ, deserialized, framed into characters, 4B/5B or 5B/6B decoded, and checked for transmission errors. The recovered 8- or 10-bit decoded characters are then written to an internal Receive FIFO, and presented to the destination host system. The integrated 4B/5B and 5B/6B encoder/decoder may be bypassed (disabled) for systems that present externally encoded or scrambled data at the parallel interface. With the encoder bypassed, the pre-encoded parallel data stream is converted to and from a serial NRZI stream. The embedded FIFOs may also be bypassed (disabled) to create a reference-locked serial transmission link. For those systems requiring even greater FIFO storage capability, external FIFOs may be directly coupled to the CY7C9689A through the parallel interface without the need for additional glue-logic. The TTL parallel I/O interface may be configured as either a FIFO (configurable for depth expansion through external FIFOs) or as a pipeline register extender. The FIFO configurations are optimized for transport of time-independent (asynchronous) 8- or 10-bit character-oriented data across a link. A Built-In Self-Test (BIST) pattern generator and checker allows for testing of the high-speed serial data paths in both the transmit and receive sections, and across the interconnecting links. HOTLink devices are ideal for a variety of applications where parallel interfaces can be replaced with high-speed, point-to-point serial links. Some applications include interconnecting workstations, backplanes, servers, mass storage, and video transmission equipment. 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised November 17, 2014 CY7C9689A Contents TAXI HOTLink Transceiver Logic Block Diagram ....... 3 Pin Configuration ............................................................. 4 Pin Descriptions ............................................................... 5 CY7C9689A HOTLink Operation ................................... 14 Overview ................................................................... 14 Transmit Data Path ................................................... 14 Receive Data Interface .............................................. 14 Oscillator Speed Selection ........................................ 14 CY7C9689A TAXI HOTLink Transceiver Block Diagram Description ............................................ 15 Transmit FIFO ........................................................... 16 Encoder Block ........................................................... 16 Transmit Shifter ......................................................... 17 Routing Matrix ........................................................... 17 Serial Line Drivers ..................................................... 17 Transmit PLL Clock Multiplier .................................... 17 Transmit Control State Machine ................................ 18 Serial Line Receivers ................................................ 18 Signal Detect ............................................................. 18 Clock/Data Recovery ................................................. 18 Clock Divider ............................................................. 19 Deserializer/Framer ................................................... 19 Decoder Block ........................................................... 19 Receive Control State Machine ................................. 19 Receive FIFO ............................................................ 21 Receive Input Register .............................................. 21 Receive Output Register ........................................... 21 Maximum Ratings ........................................................... 23 Operating Range ....................................................... 23 CY7C9689A DC Electrical Characteristics ................... 23 AC Test Loads and Waveforms ..................................... 24 Capacitance[16] .............................................................. 24 CY7C9689A Transmitter TTL Switching Characteristics, FIFO Enabled .................... 25 CY7C9689A Receiver TTL Switching Characteristics, FIFO Enabled .................... 26 CY7C9689A Transmitter TTL Switching Characteristics, FIFO Bypassed ................. 26 CY7C9689A Receiver TTL Switching Characteristics, FIFO Bypassed ................. 27 CY7C9689A REFCLK Input Switching Characteristics .............................................. 28 CY7C9689A Receiver Switching Characteristics .............................................. 28 CY7C9689A Transmitter Switching Characteristics .............................................. 29 CY7C9689A HOTLink Transmitter Switching Waveforms .................................................... 29 Document Number: 38-02020 Rev. *H CY7C9689A HOTLink Receiver Switching Waveforms .................................................... 35 Output Enable Timing .............................................. 36 Functional Description ................................................... 38 CY7C9689A TAXI HOTLink Transmit-Path Operating Mode Descriptions ....................................... 39 Synchronous Encoded .............................................. 39 Synchronous Pre-encoded ........................................ 39 Asynchronous Encoded ............................................ 39 CY7C9689A TAXI HOTLink Receive-Path Operating Mode Descriptions ....................................... 39 Synchronous Decoded .............................................. 39 Synchronous Undecoded .......................................... 40 Asynchronous Decoded ............................................ 40 Asynchronous Undecoded ........................................ 40 BIST Operation and Reporting ...................................... 40 BIST Enable Inputs ................................................... 41 BIST Transmit Path ................................................... 41 BIST Receive Path .................................................... 42 BIST Three-state Control .......................................... 42 Bus Interfacing ............................................................... 42 Shared Bus Interface Concept .................................. 43 Device Selection ........................................................ 43 Address Match and FIFO Flag Access ...................... 43 Device Selection ........................................................ 44 Transmit Data Selection ............................................ 44 Receive Data Selection ............................................. 45 FIFO Reset Address Match ....................................... 47 FIFO Reset Sequence ............................................... 48 Transmit FIFO Reset Sequence ................................ 48 Receive FIFO Reset Sequence ................................. 51 Printed Circuit Board Layout Suggestions ................. 52 Ordering Information ...................................................... 53 Ordering Code Definitions ......................................... 53 Package Diagram ............................................................ 53 Acronyms ........................................................................ 54 Document Conventions ................................................. 54 Units of Measure ....................................................... 54 Document History Page ................................................. 55 Sales, Solutions, and Legal Information ...................... 56 Worldwide Sales and Design Support ....................... 56 Products .................................................................... 56 PSoC® Solutions ...................................................... 56 Cypress Developer Community ................................. 56 Technical Support ..................................................... 56 Page 2 of 56 CY7C9689A Figure 1. HOTLink System Connections TAXI HOTLink Transceiver Logic Block Diagram TX STATUS TXDATA/TXCMD CONTROL TXCLK MODE REFCLK 10 RX STATUS RXDATA/RXCMD RXCLK 13 8 13 3 4 Mode Control Output Register MUX MUX Output Register Input Register Flags Mode Receive FIFO Flags Transmit FIFO CONTROL CE TXEN RXEN TXHALT TXRST RXRST RFEN TXBISTEN RXBISTEN RESET Transmit PLL Clock Multiplier MUX Pipeline Register MUX Pipeline Register Receive Control State Machine BIST LFSR 4B/5B, 5B/6B Encoder Transmit Control State Machine MUX Serial Shifter Bit Clock MODE RANGESEL SPDSEL RXMODE[1:0] FIFOBYP EXTFIFO ENCBYP BYTE8/10 TEST BIST LFSR 4B/5B, 5B/6B Decoder Deserializer Framer Receive Clock/Data Recovery Clock Divider Bit Clock RXSTATUS LFI RXEMPTY RXHALF RXFULL TX STATUS TXEMPTY TXHALF TXFULL Routing Matrix Signal Validation DLB OUTA INA OUTB CURSETB CURSETA Document Number: 38-02020 Rev. *H INB A/B CARDET Page 3 of 56 CY7C9689A VSSA RXBISTEN VSSA CURSETB VDDA OUTB+ VSSA OUTB– VSSA INB– VDDA INB+ VDDA OUTA+ OUTA– VSSA VSSA INA– VDDA INA+ VDDA VDDA CURSETA VSSA CARDET Pin Configuration TEST 1 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 A/B 2 74 RANGESEL LFI 3 73 RFEN VSS 4 72 TXFULL DLB 5 71 CE VLTN 6 70 TXHALF TXBISTEN 7 69 RXEN RXCLK 8 68 TXCLK TXHALT 9 67 RXRST RXFULL 10 66 VSS VSS 11 65 RXSC/D REFCLK 12 64 VDD VSS 13 63 VSS VDD 14 62 VDD VSS 15 61 RXDATA[0] TXRST 16 60 TXEMPTY VDD 17 59 RXDATA[1] TXEN 18 58 TXCMD[1] RXHALF 19 57 VSS TXSC/D 20 56 TXCMD[0] RXEMPTY 21 55 VDD TXDATA[0] 22 54 TXDATA[9]/TXCMD[2] RXDATA[11]/RXCMD[1] 23 53 RXDATA[2] RXMODE[1] 24 52 VSS RXMODE[0] 25 51 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Document Number: 38-02020 Rev. *H Transmit Data Receive FIFO Status System Host EXTFIFO BYTE8/10 Transmit FIFO RXDATA[3] RXDATA[4] Encoder 4B/5B, 5B/6B RXDATA[5] Serializer TXDATA[7] RXDATA[6] TXDATA[6] RXDATA[7] TXDATA[5] VSS TXDATA[8]/TXCMD[3] Decoder 4B/5B, 5B/6B Serial Link RESET Control CY7C9689A Deserializer Framer Serializer Encoder 4B/5B, 5B/6B Data Transmit VSS Serial Link CY7C9689A Status VSS TXDATA[4] VDD TXDATA[3] RXDATA[8]/RXCMD[3] TXDATA[2] TXDATA[1] RXDATA[9]/RXCMD[2] RXDATA[10]/RXCMD[0] FIFOBYP Framer Deserializer ENCBYP Decoder 4B/5B, 5B/6B Control FIFO Transmit System Host Data Receive FIFO Receive VSS CY7C9689A SPDSEL Receive Data Page 4 of 56 CY7C9689A ( Pin Descriptions Pin Name I/O Characteristics Signal Description Transmit Path Signals 68 TXCLK TTL clock input Internal Pull-up Transmit FIFO Clock. Used to sample all Transmit FIFO and related interface signals. 44, 42, TXDATA[7:0] 40, 36, 34, 32, 30, 22 TTL input, sampled on Parallel Transmit DATA Input. TXCLK or REFCLK When selected (CE = LOW and TXEN = asserted), information on these inputs is processed as DATA when TXSC/D is LOW and ignored otherwise. When the Internal Pull-up encoder is bypassed (ENCBYP is LOW), TXDATA[7:0] functions as the least significant eight bits of the 10- or 12-bit pre-encoded transmit character. When the Transmit FIFO is enabled (FIFOBYP is HIGH), these inputs are sampled on the rising edge of TXCLK. When the Transmit FIFO is bypassed (FIFOBYP is LOW) these inputs are captured on the rising edge of REFCLK. 54, 46 TXDATA[9:8]/ TXCMD[2:3] TTL input, sampled on Parallel Transmit DATA or COMMAND Input. TXCLK or REFCLK When selected, BYTE8/10 is HIGH, and the encoder is enabled (ENCBYP is HIGH), information on these inputs are processed as TXCMD[2:3] if TXSC/D is Internal Pull-up HIGH and ignored otherwise. When selected, BYTE8/10 is LOW, and the encoder is enabled (ENCBYP is HIGH), information on these inputs are processed as TXDATA[9:8] if TXSC/D is LOW and ignored otherwise. When the encoder is bypassed (ENCBYP is LOW), TXDATA[9:8] functions as the 9th and 10th bits of the 10- or 12-bit pre-encoded transmit character. When the Transmit FIFO is enabled (FIFOBYP is HIGH), these inputs are sampled on the rising edge of TXCLK. When the Transmit FIFO is bypassed (FIFOBYP is LOW), these inputs are captured on the rising edge of REFCLK. 58, 56 TXCMD[1:0] TTL input, sampled on Parallel Transmit COMMAND Input. TXCLK or REFCLK When selected and the encoder is enabled (ENCBYP is HIGH), information on Internal Pull-up these inputs is processed as a COMMAND when TXSC/D is HIGH and ignored otherwise. When BYTE8/10 is HIGH and the encoder is bypassed (ENCBYP is LOW), the TXCMD[1:0] inputs are ignored. When BYTE8/10 is LOW and when the encoder is bypassed (ENCBYP is LOW), the TXCMD[1:0] inputs function as the 11th and 12th (MSB) bits of the 12-bit pre-encoded transmit character. When the Transmit FIFO is enabled (FIFOBYP is HIGH), these inputs are sampled on the rising edge of TXCLK. When the Transmit FIFO is bypassed (FIFOBYP is LOW), these inputs are sampled on the rising edge of REFCLK. 20 TTL input, sampled on COMMAND or DATA input selector. TXCLK or REFCLK When selected, BYTE8/10 is HIGH, and the encoder is enabled (ENCBYP is Internal Pull-up HIGH), this input selects if the DATA or COMMAND inputs are processed. If TXSC/D is HIGH, the value on TXCMD[3:0] is captured as one of sixteen possible COMMANDs, and the data on the TXDATA[7:0] bits are ignored. If TXSC/D is LOW, the information on TXDATA[7:0] is captured as one of 256 possible 8-bit DATA values, and the information on the TXCMD[3:0] bus is ignored. When BYTE8/10 is LOW and the encoder is enabled (ENCBYP is HIGH) this input selects if the DATA or COMMAND inputs are processed. If TXSC/D is HIGH, the information on TXCMD[1:0] is captured as one of four possible COMMANDs, and the information on the TXDATA[9:0] bits are ignored. If TXSC/D is LOW, the information on TXDATA[9:0] is captured as one of 1024 possible 10-bit DATA values, and the information on the TXCMD[1:0] bus is ignored. When the encoder is bypassed (ENCBYP is LOW) TXSC/D is ignored TXSC/D Document Number: 38-02020 Rev. *H Page 5 of 56 CY7C9689A Pin Descriptions Pin Name (continued) I/O Characteristics Signal Description 18 TXEN TTL input, sampled on Transmit Enable. TXCLK or REFCLK TXEN is sampled on the rising edge of the TXCLK or REFCLK input and enables parallel data bus write operations (when selected). The device is selected when Internal Pull-up TXEN is asserted during a clock cycle immediately following one in which CE is sampled LOW. Depending on the level on EXTFIFO, the asserted state for TXEN can be active HIGH or active LOW. If EXTFIFO is LOW, then TXEN is active LOW and data is captured on the same clock cycle where TXEN is sampled LOW. If EXTFIFO is HIGH, then TXEN is active HIGH and data is captured on the clock cycle following any clock edge when TXEN is sampled HIGH. 7 TXBISTEN TTL input, asynchronous Internal Pull-up 16 TXRST TTL input, sampled on Reset Transmit FIFO. TXCLK When the Transmit FIFO is enabled (FIFOBYP is HIGH), TXEN is deasserted, CE Internal Pull-up is asserted (LOW), and TXRST is sampled LOW by TXCLK for seven cycles, the Transmit FIFO begins its internal reset process. The Transmit FIFO TXFULL flag is asserted and the host interface counter and address pointer are zeroed. This reset propagates to the serial transmit side, any remaining counters and pointers. The TXFULL flag is asserted until both sides of the Transmit FIFO have reset. While TXRST remains asserted, the Transmit FIFO remains in reset and the TXFULL output remains asserted. When the Transmit FIFO is bypassed (FIFOBYP is LOW), TXRST is ignored. 9 TXHALT TTL input, sampled on Transmitter Halt Control Input. When TXHALT is asserted LOW, transmission of data is suspended and the TXCLK Internal Pull-up HOTLink TAXI transmits SYNC characters. When TXHALT is deasserted HIGH, normal data processing proceeds. If the Transmit FIFO is enabled (FIFOBYP is HIGH), the interface is allowed to continue loading data into the Transmit FIFO while TXHALT is asserted. 72 TXFULL Three-state TTL output, Transmit FIFO Full Status Flag. changes following When the Transmit FIFO is enabled (FIFOBYP is HIGH) and its flags are driven TXCLK or REFCLK (CE is LOW), TXFULL is asserted when four or fewer characters can be written to the HOTLink Transmit FIFO. If a Transmit FIFO reset has been initiated (TXRST was sampled asserted for a minimum of seven TXCLK cycles), TXFULL is asserted to enforce the full/unavailable status of the Transmit FIFO during reset. When the Transmit FIFO is bypassed (FIFOBYP is LOW), the TXFULL output changes after the rising edge of REFCLK. TXFULL is asserted when the transmitter is BUSY (not accepting a new data or command characters) and deasserted when new characters can be accepted. When the Transmit FIFO is bypassed and RANGESEL is HIGH or SPDSEL is LOW, TXFULL toggles at the character rate to provide a character rate reference control-indication since REFCLK is operating at twice of the data rate. The asserted state of this output (HIGH or LOW) is determined by the state of the EXTFIFO input. When EXTFIFO is LOW, TXFULL is active LOW. When EXTFIFO is HIGH, TXFULL is active HIGH. Document Number: 38-02020 Rev. *H Transmitter BIST Enable. When TXBISTEN is LOW, the transmitter generates a 511-character repeating sequence that can be used to validate link integrity. This 4B/5B BIST sequence is generated regardless of the state of other configuration inputs. The transmitter returns to normal operation when TXBISTEN is HIGH. All Transmit FIFO read operations are suspended when BIST is active. Page 6 of 56 CY7C9689A Pin Descriptions Pin Name (continued) I/O Characteristics Signal Description 70 TXHALF Three-state TTL output, Transmit FIFO Half-full Status Flag. changes following When the Transmit FIFO is enabled (FIFOBYP is HIGH and CE is LOW) TXHALF TXCLK is asserted when the HOTLink Transmit FIFO is half full (128 characters is half full). If a Transmit FIFO reset has been initiated (TXRST was sampled asserted for a minimum of seven TXCLK cycles), TXHALF is asserted to enforce the full/unavailable status of the Transmit FIFO during reset. When the Transmit FIFO is bypassed (FIFOBYP is LOW), TXHALF remains deasserted, having no logical function. TXHALF is forced to the High-Z state only during a “full-chip” reset (i.e., while RESET is LOW). 60 TXEMPTY Three-state TTL output, Transmit FIFO Empty Status Flag. When the Transmit FIFO is enabled (FIFOBYP is HIGH and CE is LOW), changes following TXCLK or REFCLK TXEMPTY is asserted when the HOTLink Transmit FIFO has no data to forward to the encoder. If a Transmit FIFO reset has been initiated (TXRST was sampled asserted for a minimum of seven TXCLK cycles), TXEMPTY is deasserted and remains deasserted until the Transmit FIFO reset operation is complete. When the Transmit FIFO is bypassed (FIFOBYP is LOW), TXEMPTY is asserted to indicate that the transmitter can accept data. TXEMPTY is also used as a BIST progress indicator when TXBISTEN is asserted. When TXBISTEN is asserted LOW, TXEMPTY becomes the transmit BIST-loop counter indicator (regardless of the logic state of FIFOBYP). In this mode TXEMPTY is asserted for one TXCLK or REFCLK period at the end of each transmitted BIST sequence. Note: During BIST operations, when the Transmit FIFO is enabled (FIFOBYP is HIGH), it is necessary to keep TXCLK operating, even though no data is loaded into the Transmit FIFO and TXEN is never asserted, to allow the TXEMPTY flag to respond to the BIST state changes. The asserted state of this output (HIGH or LOW) is determined by the state of the EXTFIFO input. When EXTFIFO is LOW, TXEMPTY is active LOW. When EXTFIFO is HIGH, TXEMPTY is active HIGH. If CE is sampled asserted (LOW), TXEMPTY is driven to an active state. If CE is sampled deasserted (HIGH), TXEMPTY is placed into a High-Z state. Receive Path Signals 8 RXCLK 41, 43, RXDATA[7:0] 45, 47, 48, 53, 59,61 Bidirectional TTL clock Receive Clock. Internal Pull-up When the Receive FIFO is enabled (FIFOBYP is HIGH), this clock is the Receive interface input clock and is used to control Receive FIFO read and reset, operations. When the Receive FIFO is bypassed (FIFOBYP is LOW), this clock becomes the recovered Receive PLL character clock output which runs continuously at the character rate. Three-state TTL output, Parallel Receive DATA Outputs. changes following When the decoder is enabled (ENCBYP is HIGH), the low-order eight bits of the decoded DATA character are presented on the RXDATA[7:0] outputs. COMMAND RXCLK characters, when they are received, do not disturb these outputs. When the decoder is bypassed, the low order eight bits of the non-decoded character are presented on the RXDATA[7:0] outputs. When the Receive FIFO is disabled (FIFOBYP is LOW), these outputs change on the rising edge of the RXCLK output. When the Receive FIFO is enabled (FIFOBYP is HIGH), these outputs change on the rising edge of RXCLK input. RXEN is the three-state control for RXDATA[7:0]. Document Number: 38-02020 Rev. *H Page 7 of 56 CY7C9689A Pin Descriptions Pin Name 31, 33 RXDATA[9:8]/ RXCMD[2:3] (continued) I/O Characteristics Signal Description Three-state TTL output, Parallel Receive DATA or COMMAND Output. changes following When BYTE8/10 is HIGH and the decoder is enabled (ENCBYP is HIGH) these RXCLK outputs reflects the value for the most recently received RXCMD[2:3]. When BYTE8/10 is LOW and the decoder is enabled (ENCBYP is HIGH) these outputs reflects the value for the most recently received RXDATA[9:8]. When the decoder is bypassed (ENCBYP is LOW), RXDATA[9:8] functions as the 9th and 10th bits of the 10- or 12-bit non-decoded receive character. When the Receive FIFO is disabled (FIFOBYP is LOW), these outputs change on the rising edge of the RXCLK output. When the Receive FIFO is enabled (FIFOBYP is HIGH), these outputs change on the rising edge of the RXCLK input. RXEN is a three-state control for RXDATA[9:8]/RXCMD[2:3]. 23, 29 RXDATA[11:10] Three-state TTL output, Parallel Receive COMMAND Outputs. /RXCMD[1:0] changes following When the decoder is enabled (ENCBYP is HIGH) these outputs reflect the value RXCLK for the most recently received RXCMD[1:0]. When BYTE8/10 is HIGH and the decoder is bypassed (ENCBYP is LOW), these outputs have no meaning and are driven LOW. When BYTE8/10 is LOW and the decoder is bypassed (ENCBYP is LOW), RXCMD[1:0] functions as the 11th and 12th (MSB) bits of the 12-bit non-decoded receive character. When the Receive FIFO is disabled (FIFOBYP is LOW), this output changes on the rising edge of the RXCLK output. When the Receive FIFO is enabled (FIFOBYP is HIGH), these outputs change on the rising edge of the RXCLK input. RXEN is a three-state control for RXCMD[1:0]. 69 RXEN TTL input, sampled on RXCLK Internal Pull-up 65 RXSC/D Three-state TTL output, COMMAND or DATA Output Indicator. When BYTE8/10 is HIGH and the decoder is enabled (ENCBYP is HIGH), this changes following RXCLK output indicates which group of outputs have been updated. If RXSC/D is HIGH, RXCMD[3:0] contains a new COMMAND. The DATA on the RXDATA[7:0] pins remain unchanged. If RXSC/D is LOW, RXDATA[7:0] contains a new DATA character. The COMMAND output on RXCMD[3:0] remain unchanged. When BYTE8/10 is LOW and the decoder is enabled (ENCBYP is HIGH), this output indicates which group of outputs have been updated. If RXSC/D is HIGH, RXCMD[1:0] contains a new COMMAND and the DATA on the RXDATA[9:0] remain unchanged. If RXSC/D is LOW, RXDATA[9:0] contains a new DATA character and the COMMAND output on RXCMD[1:0] remain unchanged. When the decoder is bypassed (ENCBYP is LOW) RXSC/D is not used and may be left unconnected. RXEN is a three-state control for RXSC/D. 6 VLTN Three-state TTL output, changes following RXCLK Internal Pull-down Document Number: 38-02020 Rev. *H Receive Enable Input. RXEN is a three-state control for the parallel data bus read operations. RXEN is sampled on the rising edge of the RXCLK input (or output) and enables parallel data bus read operations (when selected). The device is selected when RXEN is asserted during an RXCLK cycle immediately following one in which CE is sampled LOW. The parallel data pins are driven to active levels after the rising edge of RXCLK. When RXEN is de-asserted (ending the selection) the parallel data pins are High-Z after the rising edge of RXCLK. Depending on the level on EXTFIFO, this signal can be active HIGH or active LOW. If EXTFIFO is LOW, then RXEN is active LOW. If EXTFIFO is HIGH, then RXEN is active HIGH. Data is delivered on the clock cycle following any clock edge when RXEN is active. Code Rule Violation Detected. VLTN is asserted in response to detection of a 4B/5B or 5B/6B character that does not meet the coding rules of these characters. When VLTN is asserted, the values on the output DATA and COMMAND buses remain unchanged. VLTN remains asserted for one RXCLK period. VLTN is used to report character mismatches when RXBISTEN is driven LOW. VLTN is driven LOW when the decoder is bypassed (ENCBYP is LOW). RXEN is a three-state control for VLTN. Page 8 of 56 CY7C9689A Pin Descriptions Pin 67 Name RXRST (continued) I/O Characteristics Signal Description TTL input, sampled on Receive FIFO Reset. Active LOW. RXCLK When the Receive FIFO is enabled (FIFOBYP is HIGH), RXEN is deasserted, CE Internal Pull-up is asserted (LOW), and RXRST is sampled while asserted (LOW) by RXCLK for seven cycles, the Receive FIFO begins its internal reset process. Once the reset operation is started, the RXEMPTY flag is asserted and the interface counters and address pointer are zeroed. The reset operation proceeds to clear out the internal write pointers and counters. The RXEMPTY output remains asserted through the reset operation and remains asserted until new data is written to the Receive FIFO. While RXRST remains asserted, the Receive FIFO remains in reset and cannot accept received characters. When the Receive FIFO is bypassed (FIFOBYP is LOW), RXRST is ignored. 24, 25 RXMODE[1:0] Static control input TTL levels Normally wired HIGH or LOW Receiver Discard Policy Mode Select. 00b—allows all characters to be written into the Receive FIFO or output to the Receive data bus 01b—discards all JK or LM sync characters except the “last” one of a string of sync characters. Single sync characters in a data stream are included in the data written into the Receive FIFO. 1Xb—discards all JK or LM sync characters. The data stream written into the Receive FIFO does not include sync characters. 77 RXBISTEN TTL input, asynchronous Internal Pull-up Receiver BIST Enable. Active LOW. When LOW, the receiver is configured to perform a character-for-character match of the incoming data stream with a 511-character BIST sequence. The result of character mismatches are indicated on the VLTN pin. Completion of each 511-character BIST loop is accompanied by an assertion pulse on the RXFULL flag. The state of ENCBYP, FIFOBYP, and BYTE8/10 have no effect on BIST operation. 73 RFEN TTL input, asynchronous Internal Pull-up Reframe Enable. Used to control when the framer is allowed to adjust the character boundaries based on detection of one or more framing characters in the data stream. When framing is enabled (RFEN is HIGH) the receive framer realigns the serial stream to the incoming 10-bit JK sync character (if BYTE8/10 is HIGH) or the 12-bit LM sync character (if BYTE8/10 is LOW). Framing is disabled when RFEN is LOW. The deassertion of RFEN freezes the character boundary relationship between the serial stream and character clock. RFEN is an asynchronous input, sampled by the internal Receive PLL character clock. 10 RXFULL Three-state TTL output, Receive FIFO Full Flag. changes following When the Receive FIFO is enabled (FIFOBYP is HIGH) and its flags are driven RXCLK (CE is LOW), RXFULL is asserted when space is available for four or fewer characters to be written to the HOTLink Receive FIFO. If the RXCLK input is not continuous or the FIFO is accessed at a rate slower than data is being received, RXFULL may also indicate that some data has been lost because of FIFO overflow. When the Receive FIFO is bypassed (FIFOBYP is LOW), RXFULL is deasserted to indicate that valid data may be present. RXFULL is also used as a BIST progress indicator, and pulses once every pass through the 511 character BIST loop. When RXBISTEN is asserted (LOW), RXFULL becomes the receive BIST loop progress indicator (regardless of the logic state of FIFOBYP). While RXBISTEN is asserted, RXFULL is asserted until the receiver detects the start of the BIST pattern. Then RXFULL is deasserted for the duration of the BIST pattern, pulsing asserted for one RXCLK period on the last symbol of each BIST loop. If 14 of 28 consecutive symbols are received in error, RXFULL returns to the asserted state until the start of a BIST pattern is again detected. The asserted state of this output (HIGH or LOW) is determined by the state of the EXTFIFO input. When EXTFIFO is LOW, RXFULL is active LOW. When EXTFIFO is HIGH, RXFULL is active HIGH. Document Number: 38-02020 Rev. *H Page 9 of 56 CY7C9689A Pin Descriptions Pin Name (continued) I/O Characteristics Signal Description 19 RXHALF Three-state TTL output, Receive FIFO Half-full Flag. changes following When the Receive FIFO is enabled (FIFOBYP is HIGH and CE is LOW) RXHALF RXCLK is asserted when the HOTLink Receive FIFO is half full (128 characters is half full). If a Receive FIFO reset has been initiated (RXRST was sampled asserted for a minimum of seven RXCLK cycles), RXHALF is deasserted to enforce the empty/unavailable status of the Receive FIFO during reset. If FIFOBYP is LOW, RXHALF remains deasserted having no logical function. RXHALF is forced to the High-Z state only during a “full-chip” reset (i.e., while RESET is LOW). 21 RXEMPTY Three-state TTL output, Receive FIFO Empty Flag. changes following When the Receive FIFO is enabled (FIFOBYP is HIGH) and its flags are driven (CE is LOW), RXEMPTY is asserted when the HOTLink Receive FIFO has no data RXCLK to forward to the parallel interface. If a Receive FIFO reset has been initiated (RXRST was sampled asserted for a minimum of seven RXCLK cycles), RXEMPTY is asserted to enforce the empty/unavailable status of the Receive FIFO during reset. Any read operation occurring when RXEMPTY is asserted results in no change in the FIFO status, and the data from the last valid read remains on the RXDATA bus. When the Receive FIFO is bypassed but the decoder is enabled, RXEMPTY is used as a valid data indicator. When deasserted it indicates that valid data is present at the RXDATA or RXCMD outputs as indicated by RXSC/D. When asserted it indicates that a SYNC character (JK or LM) is present on the RXCMD output pins. When the Receive FIFO is bypassed (FIFOBYP is LOW), RXEMPTY is deasserted whenever data is ready. The asserted state of this output (HIGH or LOW) is determined by the state of the EXTFIFO input. When EXTFIFO is LOW, RXEMPTY is active LOW. When EXTFIFO is HIGH, RXEMPTY is active HIGH. Control Signals 71 CE TTL input sampled on TXCLK, RXCLK, or REFCLK Document Number: 38-02020 Rev. *H Chip Enable Input. Active LOW. When CE is asserted and sampled LOW by RXCLK, the Receive FIFO status flags are driven to their active states. When this input is deasserted and sampled by RXCLK, the Receive FIFO status flags are placed in a High-Z state. When CE has been sampled LOW and RXEN changes from deasserted to asserted and is sampled by RXCLK, the RXSC/D, RXDATA[7:0], RXDATA[9:8]/RXCMD[2:3] and VLTN output drivers are enabled and go to their driven levels. These pins remain driven until RXEN is sampled deasserted. When the Transmit FIFO is enabled (FIFOBYP is HIGH), and CE is asserted and sampled by TXCLK, the Transmit FIFO status flags are driven to their active states. When this input is deasserted and sampled by TXCLK, the Transmit FIFO status flags are placed in a High-Z state. When the Transmit FIFO is bypassed (FIFOBYP is LOW), and CE is asserted and sampled by REFCLK, the Transmit FIFO status flags are driven to their active states. When this input is deasserted and sampled by REFCLK, the Transmit FIFO status flags are placed in a High-Z state. When the Transmit FIFO is enabled (FIFOBYP is HIGH), CE has been sampled LOW, and TXEN changes from deasserted to asserted and is sampled by TXCLK, the TXSC/D, TXDATA[7:0], TXDATA[9:8]/RXCMD[2:3], and TXCMD[1:0] inputs are sampled and passed to the Transmit FIFO. These inputs are sampled on all consecutive TXCLK cycles until TXEN is sampled deasserted. When the Transmit FIFO is bypassed (FIFOBYP is LOW), CE has been sampled LOW, and TXEN changes from deasserted to asserted and is sampled by REFCLK, the TXSC/D, TXDATA[7:0], TXDATA[9:8]/RXCMD[2:3], and TXCMD[1:0] inputs are sampled and passed to the encoder or serializer as directed by other control inputs. These inputs are sampled on all consecutive REFCLK cycles until TXEN is sampled deasserted. Page 10 of 56 CY7C9689A Pin Descriptions Pin Name (continued) I/O Characteristics Signal Description 12 REFCLK TTL clock input PLL Frequency Reference Clock. This clock input is used as the timing reference for the transmit and receive PLLs. When the Transmit FIFO is bypassed (FIFOBYP is LOW), REFCLK is also used as the clock for the parallel transmit interface. 75 SPDSEL Static control input TTL levels Normally wired HIGH or LOW Speed Select. Used to select from one of two operating serial rates for the CY7C9689A. When SPDSEL is HIGH, the signaling rate is between 100 and 200 MBaud. When LOW, the signaling rate is between 50 and 100 MBaud. Used in combination with RANGESEL and BYTE8/10 to configure the VCO multipliers and dividers. 74 RANGESEL Static control input TTL levels Normally wired HIGH or LOW Range Select. Selects the proper prescaler for the REFCLK input. If RANGESEL is LOW, the REFCLK input is passed directly to the Transmit PLL clock multiplier. If RANGESEL is HIGH, REFLCK is divided by two before being sent to the Transmit PLL multiplier. When the Transmit FIFO is bypassed (FIFOBYP is LOW), with RANGESEL HIGH or SPDSEL LOW, TXFULL toggles at half the REFCLK rate to provide a character rate indication, and to show when data can be accepted. 51 RESET Asynchronous TTL input Master Reset for Internal Logic. Pulsed LOW for one or more REFCLK cycles. 28 FIFOBYP Static control input TTL levels Normally wired HIGH or LOW FIFO Bypass Enable. When asserted, the Transmit and Receive FIFOs are bypassed. In this mode TXCLK is not used. Instead all transmit data must be synchronous to REFCLK. Transmit FIFO status flags are synchronized to REFCLK. All received data is synchronous to RXCLK output. Receive FIFO status flags are synchronized to RXCLK (the recovered Receive PLL character clock). When not asserted, the Transmit and Receive FIFOs are enabled. In this mode all Transmit FIFO writes are synchronized to TXCLK, and all Receive FIFO reads are synchronous to the RXCLK input. 50 BYTE8/10 Static control input TTL levels Normally wired HIGH or LOW 8/10-bit Parallel Data Size Select. When set for 8-bit data (BYTE8/10 is HIGH) and the encoder is enabled (ENCBYP is HIGH), 8-bit DATA characters and 4-bit COMMAND characters are captured at the TXDATA[7:0] or TXCMD[3:0] inputs (selected by the TXSC/D input) and passed to the Transmit FIFO (if enabled) and encoder. Received characters are decoded, passed through the Receive FIFO (if enabled) and presented at either the RXDATA[7:0] or RXCMD[3:0] outputs and indicated by the RXSC/D output. When set for 8-bit data (BYTE8/10 is HIGH) and the encoder is bypassed (ENCBYP is LOW), the internal data paths are set for 10-bit characters. Each received character is presented to the Receive FIFO (if enabled) and is passed to the RXDATA[9:0] outputs. When set for 10-bit data (BYTE8/10 is LOW) and the encoder is enabled (ENCBYP is HIGH), 10-bit DATA characters and 2-bit COMMAND characters are captured at the TXDATA[9:0] or TXCMD[1:0] inputs (selected by the TXSC/D input) and passed to the Transmit FIFO (if enabled) and encoder. Received characters are decoded, passed through the Receive FIFO (if enabled) and presented at either the RXDATA[9:0] or RXCMD[1:0] outputs and indicated by the RXSC/D output. When set for 10-bit data (BYTE8/10 is LOW) and the encoder is bypassed (ENCBYP is LOW), the internal clock data paths are set for 12-bit characters. Each received character is presented to the Receive FIFO (if enabled) and is passed to the RXDATA[9:0] and the RXCMD[1:0] outputs. Document Number: 38-02020 Rev. *H Page 11 of 56 CY7C9689A Pin Descriptions Pin (continued) Name I/O Characteristics Signal Description 49 EXTFIFO Static control input TTL levels Normally wired HIGH or LOW External FIFO Mode. EXTFIFO modifies the active state of the RXEN and TXEN inputs and the timing of the Transmitter and Receiver data buses. When configured for external FIFOs (EXTFIFO is HIGH), TXEN is assumed to be driven by the empty flag of an attached CY7C42X5 FIFO, and RXEN is assumed to be driven by the almost full flag of an attached CY7C42X5 FIFO. In this mode the active data transition is in the clock following the clock edge that “enables” the data bus. When not configured for external FIFOs (EXTFIFO is LOW), TXEN is assumed to be driven as a pipeline register and RXEN is assumed to be driven by a controller for a pipeline register. In this mode the active data transition is within the same clock as the clock edge that “enables” the data bus. EXTFIFO also modifies the output state of the Receive and Transmit FIFO flags. When configured for external FIFOs (EXTFIFO is HIGH), the Full and Empty FIFO flags are active HIGH (the Half full flag is always active LOW). When not configured for external FIFOs (EXTFIFO is LOW), all of the FIFO flags are active LOW. 27 ENCBYP Static control input TTL levels Normally wired HIGH or LOW Enable Encoder Bypass Mode. When asserted, both the encoder and decoder are bypassed. Data is transmitted without 4B/5B or 5B/6B encoding (but with NRZI encoding), LSB first. Received data are presented as parallel characters to the parallel interface without decoding. When deasserted, data is passed through both the encoder in the Transmit path and the decoder in the Receive path. Analog I/O and Control 89, 90, OUTA± 81, 82 OUTB± PECL compatible differential output Differential Serial Data Outputs. These PECL-compatible differential outputs are capable of driving terminated transmission lines or commercial fiber-optic transmitter modules. To minimize the power dissipation of unused outputs, the outputs should be left unconnected and the associated CURSETA or CURSETB should be connected to VDD. 94, 93, INA± 86, 85 INB± PECL compatible differential input Differential Serial Data Inputs. These inputs accept the serial data stream for deserialization and decoding. Only one serial stream at a time may be fed to the receive PLL to extract the data content. This stream is selected using the A/B input. 97 CURSETA Analog Current-set Resistor Input for OUTA±. A precision resistor is connected between this input and a clean ground to set the output differential amplitude and currents for the OUTA± differential driver. 78 CURSETB Analog Current-set Resistor Input for OUTB±. A precision resistor is connected between this input and a clean ground to set the output differential amplitude and currents for the OUTB± differential driver. 100 CARDET PECL input, asynchronous Carrier Detect Input. Used to allow an external device to signify a valid signal is being presented to the high-speed PECL input buffers, as is typical on an Optical Module. When CARDET is deasserted LOW, the LFI indicator asserts LOW signifying a Link Fault. This input can be tied HIGH for copper media applications. 2 A/B Asynchronous TTL input Input A or Input B Selector. When HIGH, input INA± is selected, when LOW, INB± is selected. 3 LFI TTL output, changes following RXCLK Link Fault Indication Output. Active LOW. LFI changes synchronous with RXCLK. This output is driven LOW when the serial link currently selected by A/B is not suitable for data recovery. This could be because: Serial Data Amplitude is below acceptable levels Input transition density is not sufficient for PLL clock recovery Input Data stream is outside an acceptable frequency range of operation CARDET is LOW Document Number: 38-02020 Rev. *H Page 12 of 56 CY7C9689A Pin Descriptions Pin Name (continued) I/O Characteristics Signal Description 5 DLB Asynchronous TTL input Diagnostic Loop Back Selector. When DLB is LOW, LOOP Mode is OFF. Output of the transmitter shifter is routed to both OUTA± and OUTB± and the serial input selected by A/B is routed to the receive PLL for data recovery. When DLB is HIGH, Diagnostic Loopback is Enabled. Output of the transmitter serial data is routed to the receive PLL for data recovery. Primarily used for System Diagnostic test. The serial inputs are ignored and OUTA± and OUTB± are both active. 1 TEST Asynchronous TTL input normally wired HIGH Test Mode Select. Used to force the part into a diagnostic test mode used for factory ATE test. This input must be tied HIGH during normal operation. Power 80, 87, VDDA 88, 95, 96, 98 Power for PECL-compatible I/O signals and internal circuits. 76, 79, VSSA 83, 84, 91, 92, 99 Ground for PECL-compatible I/O signals and internal circuits. 14, 17, VDD 35, 55, 62, 64 Power for TTL I/O signals and internal circuits. 4,11, VSS 13, 15, 26, 37, 38, 39, 52, 57, 63, 66 Ground for TTL I/O signals and internal circuits. Document Number: 38-02020 Rev. *H Page 13 of 56 CY7C9689A CY7C9689A HOTLink Operation Overview The CY7C9689A is designed to move parallel data across both short and long distances with minimal overhead or host system intervention. This is accomplished by converting the parallel characters into a serial bit-stream, transmitting these serial bits at high speed, and converting the received serial bits back into the original parallel data format. The CY7C9689A offers a large feature set, allowing it to be used in a wide range of host systems. Some of the configuration options are Encoder Data from the host interface or Transmit FIFO is next passed to an Encoder block. The CY7C9689A contains both 4B/5B and 5B/6B encoders that are used to improve the serial transport characteristics of the data. For those systems that contain their own encoder or scrambler, this Encoder may be bypassed. Serializer/Line Driver The data from the Encoder is passed to a Serializer. This Serializer operates at 10 or 12 times the character rate. With the internal FIFOs enabled, REFCLK can run at 1x, 2x, or 4x the character rate. With the FIFOs bypassed, REFCLK can operate at 1x or 2x the character rate. The serialized data is output in NRZI format from two PECL-compatible differential line drivers configured to drive transmission lines or optical modules. ■ AMD TAXIchip 4B/5B- and 5B/6B-compatible encoder/decoder ■ AMD TAXIchip-compatible serial link ■ AMD TAXIchip parallel COMMAND and DATA I/O bus architecture Receive Data Interface ■ 8-bit or 10-bit character size ■ User-definable data packet or frame structure ■ Two-octave data rate range ■ Asynchronous (FIFOed) or synchronous data interface Serial data is received at one of two PECL-compatible differential line receivers. The data is passed to both a Clock and Data Recovery PLL and to a Deserializer that converts NRZI serial data into NRZ parallel characters. The Framer adjusts the boundaries of these characters to match those of the original transmitted characters. ■ Embedded or bypassable FIFO data storage ■ Encoded or non-encoded ■ Multi-PHY capability This flexibility allows the CY7C9689A to meet the data transport needs of almost any system. Transmit Data Path Transmit Data Interface/Transmit Data FIFO The transmit data interface to the host system is configurable as either an asynchronous buffered (FIFOed) parallel interface or as a synchronous pipeline register. The bus itself can be configured for operation with either 8-bit or 10-bit character widths. When configured for asynchronous operation (where the host-bus interface clock operates asynchronous to the serial character and bit stream clocks), the host interface becomes that of a synchronous FIFO clocked by TXCLK. In this configuration an internal 256-character Transmit FIFO is enabled that allows the host interface to be written at any rate from DC to 50 MHz. When configured for synchronous operation, the transmit interface is clocked by REFCLK and operates synchronous to the internal character and bit-stream clocks. The input register can be written at either 1/10 or 1/12 the serial bit rate. This interface can be clocked at up to 40 MHz when configured for 8-bit data width, and up to 33 MHz when configured for 10-bit data bus width. Actual clock rate depends on data rate as well as RANGESEL and SPDSEL logic levels. Line Receiver/Deserializer/Framer Decoder The parallel characters are passed through a pair of 5B/4B or 6B/5B decoders and returned to their original form. For systems that make use of external decoding or descrambling, the decoder may be bypassed. Receive Data Interface/Receive Data FIFO Data from the decoder is passed either to a synchronous Receive FIFO or is passed directly to the output register. The output register can be configured for either 8-bit character or 10-bit character operation. When configured for an asynchronous buffered (FIFOed) interface, the data is passed through a 256-character Receive FIFO that allows data to be read at any rate from DC to 50 MHz. When configured for synchronous operation (Receive FIFO is bypassed) data is clocked out of the Receive Output register at up to 20 MHz when configured for 8-bit characters, or 16.67 MHz when configured for 10-bit characters. The receive interface is also configurable for FIFO flags with either HIGH or LOW status indication Oscillator Speed Selection The CY7C9689A is designed to operate over a two-octave range of serial signaling rates, covering the 50- to 200-MBaud range. To cover this wide range, the PLLs are configured into various sub-regions using the SPDSEL and RANGESEL inputs, and to a limited extent the BYTE8/10 input. These inputs are used to configure the various prescalers and clock dividers used with the transmit and receive PLLs. Both asynchronous and synchronous interface operations support user control over the logical sense of the FIFO status flags. Full and empty flags on both the transmitter and receiver can be active HIGH or active LOW. This facilitates interfacing with existing control logic or external FIFOs with minimal or no external glue logic. Document Number: 38-02020 Rev. *H Page 14 of 56 CY7C9689A CY7C9689A TAXI HOTLink Transceiver Block Diagram Description Figure 2. Transmit Input Register TXDATA[7:0] TXCMD[3:0] TXEN TXSC/D CE 12 Transmit Input/Output Register The CY7C9689A provides a synchronous interface for data and command inputs, instead of the TAXI’s asynchronous strobed interface. The Transmit Input Register, shown in Figure 2, captures the data and command to be processed by the HOTLink Transmitter, and allows the input timing to be made compatible with asynchronous or synchronous host system buses. These buses can take the form of external FIFOs, state machines, or other control structures. Data and command present on the TXDATA[9:0] and TXSC/D inputs are captured at the rising edge of the selected sample clock. The transmit data bus bit-assignments vary depending on the data encoding and bus-width selected. These bus bit-assignments are shown in Table 1, and list the functional names of these different signals. Note that the function of several of these signals changes in different operating modes. The logical sense of the enable and FIFO flag signals depends on the intended interface convention and is set by the EXTFIFO pin. REFCLK TXCLK Transmit Input Register 14 To Encoder Block Transmit FIFO The transmit interface supports both synchronous and asynchronous clocking modes, each supporting both UTOPIA and Cascade timing models. The selection of the specific clocking mode is determined by the RANGESEL and SPDSEL inputs and the FIFO Bypass (FIFOBYP) signal. Table 1. Transmit Input Bus Signal Map Transmit Encoder Mode[1] TXDATA Bus Input Bit Encoded 8-bit Character Stream[2] TXSC/D TXSC/D Pre-encoded 10-bit Character Stream Encoded 10-bit Character Stream[3] Pre-encoded 12-bit Character Stream TXSC/D TXDATA[0] TXDATA[0] TXD[0][4] TXDATA[0] TXD[0][5] TXDATA[1] TXDATA[1] TXD[1] TXDATA[1] TXD[1] TXDATA[2] TXDATA[2] TXD[2] TXDATA[2] TXD[2] TXDATA[3] TXDATA[3] TXD[3] TXDATA[3] TXD[3] TXDATA[4] TXDATA[4] TXD[4] TXDATA[4] TXD[4] TXDATA[5] TXDATA[5] TXD[5] TXDATA[5] TXD[5] TXDATA[6] TXDATA[6] TXD[6] TXDATA[6] TXD[6] TXDATA[7] TXDATA[7] TXD[7] TXDATA[7] TXD[7] TXDATA[8]/TXCMD[3] TXCMD[3] TXD[8] TXDATA[8] TXD[8] TXDATA[9]/TXCMD[2] TXCMD[2] TXD[9] TXDATA[9][3] TXD[9] TXCMD[1] TXCMD[1] TXCMD[1] TXD[10][5] TXCMD[0] TXCMD[0] TXCMD[0] TXD[11] Notes 1. All open cells are ignored. 2. When ENCBYP is HIGH and BYTE8/10 is HIGH, transmitted bit order is the encoded form (MSB to LSB) of TXDATA[7,6,5,4] and TXDATA[3,2,1,0] or TXCMD[3,2,1,0] as selected by TXSC/D. 3. When ENCBYP is HIGH and BYTE8/10 is LOW, transmitted bit order is the encoded form (MSB to LSB) of TXDATA[8,7,6,5,4] and TXDATA[9,3,2,1,0] or TXCMD[1,0] as selected by TXSC/D. 4. When ENCBYP is LOW and BYTE8/10 is HIGH, the transmitted bit order is (LSB to MSB) TXD[0,1,2,3,4,5,6,7,8,9]. 5. When ENCBYP is LOW and BYTE8/10 is LOW, the transmitted bit order is (LSB to MSB) TXD[0,1,2,3,4,5,6,7,8,9,11,10]. Document Number: 38-02020 Rev. *H Page 15 of 56 CY7C9689A Synchronous Interface Transmit FIFO Synchronous interface clocking operates the entire transmit data path synchronous to REFCLK. It is enabled by connecting FIFOBYP LOW to disable the internal FIFOs. The Transmit FIFO is used to buffer data and command captured in the input register for later processing and transmission. This FIFO is sized to hold 256 14-bit characters. When the Transmit FIFO is enabled, and a Transmit FIFO write is enabled (the device is selected and TXEN is sampled asserted), data is captured in the transmit input register and stored into the Transmit FIFO. All Transmit FIFO write operations are clocked by TXCLK. Asynchronous Interface Asynchronous interface clocking controls the writing of host bus data into the Transmit FIFO. It is enabled by setting FIFOBYP HIGH to enable the internal FIFOs. In these configurations, all writes to the Transmit Input Register, and associated transfers to the Transmit FIFO, are controlled by TXCLK. The remainder of the transmit data path is clocked by REFCLK or synthesized derivatives of REFCLK. Shared Bus Timing Model The Shared Bus Timing Model allows multiple CY7C9689A transmitters to be accessed from a common host bus. It is enabled by setting EXTFIFO LOW. In shared bus timing, the TXEMPTY and TXFULL outputs and TXEN input are all active LOW signals. If the CY7C9689A is addressed by asserting CE LOW, it becomes “selected” when TXEN is asserted LOW. Following selection, data or command is written into the Transmit FIFO on every clock cycle where TXEN remains LOW. Cascade Timing Model The Cascade timing model is a variation of the shared bus timing model. Here the TXEMPTY and TXFULL outputs, and TXEN input, are all active HIGH signals. Cascade timing makes use of the same selection sequences as shared bus timing, but write data accesses use a delayed write. This delayed write is necessary to allow direct coupling to external FIFOs, or to state machines that initiate a write operation one clock cycle before the data is available on the bus. The Transmit FIFO presents Full, Half-Full, and Empty FIFO flags. These flags are provided synchronous to TXCLK. When the Transmit FIFO is enabled, it allows operation with a Moore-type external controlling state machine. When configured for Cascade timing, the timing and active levels of these signals are also designed to support direct expansion to Cypress CY7C42x5 synchronous FIFOs. Regardless of bus width (8- or 10-bit characters) the Transmit FIFO can be clocked at any rate from DC to 50 MHz. This gives the Transmit FIFO a maximum bandwidth of 50 million characters per second. Since the serial outputs can only move 20 million characters per second at their fastest operating rate, there is ample time to service multiple CY7C9689A HOTLinks with a single controller. The read port of the Transmit FIFO is connected to a logic block that performs data formatting and validation. All data read operations from the Transmit FIFO are controlled by a Transmit Control State Machine that operates synchronous to REFCLK. Encoder Block The Encoder logic block performs two primary functions: encoding the data for serial transmission and generating BIST patterns to allow at-speed link and device testing. Cascade timing is enabled by setting EXTFIFO HIGH. BIST LFSR When used for FIFO depth expansion, Cascade timing allows the size of the internal Transmit FIFO to be expanded to an almost unlimited depth. It allows a CY7C42x5 series synchronous FIFO to be attached to the transmit interface without any extra logic, as shown in Figure 3. The Encoder logic block operates on data stored in a register. This register accepts information directly from the Transmit FIFO, the Transmit Input Register or from the Transmit Control State Machine when it inserts special characters into the data stream. Figure 3. External FIFO Depth Expansion of the CY7C9689A Transmit Data Path This same register is converted into a Linear Feedback Shift Register (LFSR) when the BIST pattern generator is enabled (TXBISTEN is LOW). When enabled, this LFSR generates a 511-character sequence that includes all Data and Special Character codes, including the explicit violation symbols. This provides a predictable but pseudo-random sequence that can be matched to an identical LFSR in the Receiver. CY7C42x5 FIFO FF* WEN* D TXCLK FF* WEN* D WCLK CY7C9689A TXEN EF* REN* TXFULL Q TXDATA TXSC/D TXCLK RCLK “1” EXTFIFO Encoder The data passed through the Transmit FIFO and pipeline register, or as received directly from the Transmit Input Register, is seldom in a form suitable for transmission across a serial link. The characters must usually be processed or transformed to guarantee: ■a minimum transition density (to allow the serial receiver PLL to extract a clock from the data stream) ■some way to allow the remote receiver to determine the correct character boundaries (framing). Document Number: 38-02020 Rev. *H Page 16 of 56 CY7C9689A The CY7C9689A contains an integrated 4B/5B encoder that accepts 8-bit data characters and converts these into 10-bit transmission characters that have been optimized for transport on serial communications links. This 4B/5B encoding scheme is compliant with the ANSI X3T9.5 (FDDI) committee’s 4B/5B code. The CY7C9689A also contains a 5B/6B encoder that accepts 10-bit data characters and converts these into 12-bit transmission characters. The 4B/5B, 5B/6B encoder can be bypassed for those systems that operate with external 4B/5B or 5B/6B encoders or use alternate forms of encoding or scrambling to ensure good transmission characteristics. The complete encoding tables are listed in Table 7 and Table 8. When the Encoder is enabled, the transmit data characters (as passed through the Transmit FIFO and pipeline register) are converted to either a 10-bit or 12-bit Data symbol or a 10-bit or 12-bit Command Character, depending upon the state of the TXSC/D input. If TXSC/D is HIGH, the data on the command inputs are encoded into Command Character as shown in Table 8. If TXSC/D is LOW, the data inputs are encoded using the Data Character encoding in Table 7. The 4B/5B, 5B/6B coding function of the Encoder can be bypassed for systems that include an external coder or scrambler function as part of the controller or host system. This is performed by setting ENCBYP LOW. With the encoder bypassed, each 10-bit or 12-bit character (as captured in the Transmit Input Register) is passed directly to the Transmit Shifter (or Transmit FIFO) without modification. Transmit Shifter The Transmit Shifter accepts 10-bit (BYTE8/10 = HIGH) or 12-bit (BYTE8/10 = LOW) parallel data from the Encoder block once each character time, and shifts it out the serial interface output buffers using a PLL-multiplied bit-clock with NRZI encoding. This bit-clock runs at 2.5, 5, or 10 times the REFCLK rate (3, 6, or 12 times when BYTE8/10 is LOW) as selected by RANGESEL and SPDSEL (see Table 3). Timing for the parallel transfer is controlled by the counter and dividers in the Clock Multiplier PLL and is not affected by signal levels or timing at the input pins. Bits in each character are shifted out LSB first. Routing Matrix The Routing Matrix is a precision multiplexor that allows local diagnostic loopback. The signal routing for the transmit serial outputs is controlled by the DLB input as listed Table 2.in Serial Line Drivers The serial interface PECL Output Drivers (ECL referenced to +5 v) are the transmission line drivers for the serial media. OUTA± receives its data directly from the transmit shifter, while OUTB± receives its data from the Routing Matrix. These two outputs (OUTA± and OUTB±) are capable of direct connection to +5 v optical modules, and can also directly drive DC- or AC-coupled transmission lines. The PECL-compatible Output Drivers can be viewed as programmable current sources. The output voltage is determined by the output current and the load impedance ZLOAD. The desired output voltage swing is therefore controlled by the current-set resistor RCURSET associated with that driver. Different RCURSET values are required for different line Document Number: 38-02020 Rev. *H Table 2. Transmit Data Routing Matrix DLB[0] Data Connections 0 TRANSMIT SHIFTER OUTA A/B OUTB INB RECEIVE PLL INA 1 TRANSMIT SHIFTER OUTA A/B OUTB INB RECEIVE PLL INA impedance/amplitude combinations. The output swing is designed to center around VDD–1.33 v. Each output must be externally biased to VDD–1.33 v. This differential output-swing can be specified two ways: either as a peak-to-peak voltage into a single-end load, or as an absolute differential voltage into a differential load. When specified into a single-ended load (one of the outputs switching into a load), the single output will both source and sink current as it changes between its HIGH and LOW levels. The voltage difference between this HIGH level and LOW level determine the peak-to-peak signal-swing of the output. This amplitude relationship is controlled by the load impedance on the driver, and by the resistance of the RCURSET resistor for that driver, as listed in Eq. 1 180 Z LOAD R CURSET = --------------------------------V OPP Eq. 1 In Eq. 1, VOPP is the difference in voltage levels at one output of the differential driver when that output is driving HIGH and LOW, ZLOAD is that load seen by the one output when it is sourcing and sinking current. With a known load impedance and a desired signal swing, it is possible to calculate the value of the associated CURSETA or CURSETB resistor that sets this current. Unused differential output drivers should be left open, and can reduce their power dissipation by connecting their respective CURSETx input to VDD. Transmit PLL Clock Multiplier The Transmit PLL Clock Multiplier accepts an external clock at the REFCLK input, and multiples that clock by 2.5, 5, or 10 (3, 6, or 12 when BYTE8/10 is LOW and the encoder is disabled) to generate a bit-rate clock for use by the transmit shifter. It also provides a character-rate clock used by the Transmit Controller state machine. The clock multiplier PLL can accept a REFCLK input between 8 MHz and 40 MHz, however, this clock range is limited by the operation mode of the CY7C9689A as selected by the SPDSEL and RANGESEL inputs, and to a limited extent, by the BYTE8/10 Page 17 of 56 CY7C9689A and FIFOBYP signals. The operating serial signalling rate and allowable range of REFCLK frequencies is listed in Table 3. Transmit Control State Machine The Transmit Control State Machine responds to multiple inputs to control the data stream passed to the encoder. It operates in response to: Table 3. Speed Select and Range Select Settings RANGESEL Serial Data Rate (MBaud) REFCLK[7] Frequency (MHz) LOW LOW 50–100 10–20 LOW HIGH[6] 50–100 20–40 HIGH LOW 100–200 10–20 HIGH HIGH 100–200 20–40 SPDSEL TXHALT may be used to prevent a remote FIFO overflow, which would result in lost data. This back-pressure mechanism can significantly improve data integrity in systems that cannot guarantee the full bandwidth of the host system at all times. Serial Line Receivers Two differential line receivers, INA± and INB±, are available for accepting serial data streams, with the active input selected using the A/B input. The DLB input allow the transmit Serializer output to be selected as a third input serial stream, but this path is generally used only for local diagnostic loopback purposes. The serial line receiver inputs are all differential, and will accommodate wire interconnect with filtering losses or transmission line attenuation greater than 9 dB (VDIF > 200 mV, or 400 mV peak-to-peak differential) or can be directly connected to +5 v fiber-optic interface modules (any ECL logic family, not limited to ECL 100K). The common-mode tolerance of these line receivers accommodates a wide range of signal termination voltages. ■the state of the FIFOBYP input ■the presence of data in the Transmit FIFO ■the contents of the Transmit FIFO ■the state of the transmitter BIST enable (TXBISTEN) As can be seen in Table 2, these inputs are configured to allow single-pin control for most applications. For those systems requiring selection of only INA± or INB±, the DLB signals can be tied LOW, and the A/B selection can be performed using only A/B. For those systems requiring only a single input and a local loopback, the A/B can be tied HIGH or LOW, and DLB can be used for loopback control. ■the state of external halt signal (TXHALT). Signal Detect These signals are used by the Transmit Control State Machine to control the data formatter, read access to the Transmit FIFO and BIST. They determine the content of the characters passed to the Encoder and Transmit Shifter. The selected Line Receiver (that routed to the clock and data recovery PLL) is simultaneously monitored for: When the Transmit FIFO is bypassed, the Transmit Control State Machine operates synchronous to REFCLK. In this mode, data from the TXDATA bus is passed directly from the Input Register to the Pipeline Register. If no data is enabled into the Input register (TXEN is deasserted or TXFULL is asserted) then the Transmit Control State Machine presents a JK or LM (when BYTE8/10 = LOW) Command Character code to the Encoder to maintain link synchronization. ■transition If both the Encoder and Transmit FIFO are bypassed and no data is enabled into the Input Register, the Transmit Control State Machine injects JK or LM (when BYTE8/10 = LOW) into the Serial Shifter Register at this time slot. This also occurs if the Encoder is bypassed, the Transmit FIFO is enabled, and the Transmit FIFO is empty. External Control of Data Flow The Transmit Control State Machine supports halting of data transmission by the TXHALT input. This control signal input is only interpreted when the Transmit FIFO is enabled. TXHALT is brought directly to the state machine without going through the Transmit FIFO. The assertion of TXHALT causes character processing to stop at the next FIFO character location. No additional data is read from the Transmit FIFO until TXHALT is deasserted. ■analog amplitude (> 400 mV pk-pk) density ■received data stream outside normal frequency range (±400 ppm) ■carrier detected All of these conditions must be valid for the Signal Detect block to indicate a valid signal is present. This status is presented on the LFI (Link Fault Indicator) output, which changes synchronous to RXCLK. While link status is monitored internally at all times, it is necessary to have transitions on RXCLK to allow this signal to change externally. Clock/Data Recovery The extraction of a bit-rate clock and recovery of data bits from the received serial stream is performed within the Clock/Data Recovery (CDR) block. The clock extraction function is performed by a high-performance embedded PLL that tracks the frequency of the incoming bit stream and aligns the phase of its internal bit-rate clock to the transitions in the serial data stream. The CDR makes use of the clock present at the REFCLK input. It is used to ensure that the VCO (within the CDR) is operating at the correct frequency (rather than some harmonic of the bit rate), to improve PLL acquisition time, and to limit unlocked frequency excursions of the CDR VCO when no data is present at the serial inputs. Notes 6. When SPDSEL is LOW and the FIFOs are bypassed (FIFOBYP is LOW), the RANGESEL input is ignored and is internally mapped to the LOW setting. 7. When configured for 12-bit preencoded data (BYTE8/10 and ENCBYP are both LOW) the allowable REFCLK ranges are 8.33 to 16.67 MHz and 16.67 to 33.33 MHz. Document Number: 38-02020 Rev. *H Page 18 of 56 CY7C9689A Regardless of the type of signal present, the CDR will attempt to recover a data stream from it. If the frequency of the recovered data stream is outside the limits for the range controls, the CDR PLL will track REFCLK instead of the data stream. When the frequency of the selected data stream returns to a valid frequency, the CDR PLL is allowed to track the received data stream. The frequency of REFCLK is required to be within ±400 ppm of the frequency of the clock that drives the REFCLK signal at the remote transmitter to ensure a lock to the incoming data stream. For systems using multiple or redundant connections, the LFI output can be used to select an alternate data stream. When an LFI indication is detected, external logic can toggle selection of the INA± and INB± inputs through the A/B input. When a port switch takes place, it is necessary for the PLL to reacquire the new serial stream and frame to the incoming characters. Clock Divider This block contains the clock division logic, used to transfer the data from the Deserializer/Framer to the Decoder once every character (once every ten or twelve bits) clock. This counter is free running and generates outputs at the bit-rate divided by 10 (12 when the BYTE8/10 is LOW). When the Receive FIFO is bypassed, one of these generated clocks is driven out the RXCLK pin. Deserializer/Framer The CDR circuit extracts bits from the serial data stream and clocks these bits into the Shifter/Framer at the bit-clock rate. When enabled, the Framer examines the data stream looking for JK or LM (when BYTE8/10 is LOW) characters at all possible bit positions. The location of this character in the data stream is used to determine the character boundaries of all following characters. The framer operates in two different modes, as selected by the RFEN input. When RFEN is asserted (HIGH), the framer is allowed to reset the internal character boundaries on any detected JK or LM (when BYTE8/10 is LOW) character. If RFEN is LOW, the framer is disabled and no changes are made to character boundaries. The framer in the CY7C9689A operates by shifting the internal character position to align with the character clock. This ensures that the recovered clock does not contain any significant phase changes/hops during normal operation or framing, and allows the recovered clock to be replicated and distributed to other circuits using PLL-based logic elements. Decoder Block The decoder logic block performs two primary functions: decoding the received transmission characters back into Data and Command Character codes, and comparing generated BIST patterns with received characters to permit at-speed link and device testing. 5B/4B, 6B/5B Decoder The framed parallel output of the Deserializer is passed to the 5B/4B, 6B/5B Decoder. If the Decoder is enabled, it is transformed from a 10-bit or 12-bit transmission character back to the original Data and Command Character codes. This block uses the standard decoder patterns in Table 7 and Table 8 of this data Document Number: 38-02020 Rev. *H sheet. Data Patterns on the data bus are indicated by a LOW on RXSC/D, and Command Character codes on the command bus are indicated by a HIGH. Invalid patterns or disparity errors are signaled as errors by a HIGH on VLTN. If the Decoder is bypassed and BYTE8/10 is HIGH, the ten (10) data bits of each transmission character are passed unchanged from the framer to the Pipeline Register. When the Decoder is bypassed and BYTE8/10 is LOW, the twelve (12) data bits of each transmission character are passed unchanged from the framer to the Pipeline Register. BIST LFSR The output register of the Decoder block is normally used to accumulate received characters for delivery to the Receive Formatter block. When configured for BIST mode (RXBISTEN is LOW), this register becomes a signature pattern generator and checker by logically converting to a Linear Feedback Shift Register (LFSR). When enabled, this LFSR generates a 511-character sequence that includes all Data and Command Character codes, including the explicit violation symbols. This provides a predictable but pseudo-random sequence that can be matched to an identical LFSR in the Transmitter. When synchronized with the received data stream, it checks each character in the Decoder with each character generated by the LFSR and indicates compare errors at the VLTN output of the Receive Output Register. The LFSR is initialized by the BIST hardware to the BIST loop start code of HEX data 00 (00 is sent only once per BIST loop). Once the start of the BIST loop has been detected by the receiver, RXRVS is asserted for pattern mismatches between the received characters and the internally generated character sequence. Code rule violations or running disparity errors that occur as part of the BIST loop do not cause an error indication. RXFULL pulses asserted for one RXCLK cycle per BIST loop and can be used to check test pattern progress. The specific patterns checked by the receiver are described in Table 4. If a large number of errors are detected, the receive BIST state machine aborts the compare operations and resets the LFSR to the D0.0 state to look for the start of the BIST sequence again. Receive Control State Machine The Receive Control State Machine responds to multiple input conditions to control the routing and handling of received characters. It controls the staging of characters across various registers and the Receive FIFO. It controls the various discard policies and error control within the receiver, and operates in response to: ■the received character stream ■the room for additional data in the Receive FIFO ■the state of the receiver BIST enable (RXBISTEN) ■the state of FIFOBYP. These signals and conditions are used by the Receive Control State Machine to control the Receive Formatter, write access to the Receive FIFO, the Receive Output register, and BIST. They determine the content of the characters passed to each of these destinations. Page 19 of 56 CY7C9689A Table 4. CY7C9689A TAXI HOTLink BIST Sequence D.00 C.JK C.IH C.SR C.SS C.JK C.IH C.QI D.EE C.RR D.B3 C.QQ D.FB C.TR C.SR C.SS C.QQ D.F8 C.TS D.89 D.42 C.HI D.94 C.TT C.TR D.15 D.0C C.JK C.RS D.CD D.6A D.3D D.1E C.HH D.8F D.4B D.23 D.11 D.04 C.JK C.RS D.C5 D.68 C.II C.RS D.C0 C.TS C.QH D.D2 C.RR D.BC C.TT C.QH D.D7 D.6D D.3A C.HH C.QI D.EB D.73 D.35 D.1C C.JK C.RS D.CF D.6B D.33 C.HI D.91 D.44 C.II C.IH C.QI D.E6 C.RR D.B2 C.QI C.HQ D.A8 C.TT C.QH D.D4 C.TS D.E3 D.71 D.34 C.JK C.IH C.QI D.ED D.7A C.HI D.99 D.46 C.HI D.96 C.HQ D.AE C.HQ D.A3 D.51 D.24 C.JK C.IH C.QI D.EC C.TS C.QH D.D1 D.64 C.II C.IH C.QI C.RR C.TR C.QI D.E0 C.TS C.TR C.SR C.SS C.SS C.SS C.SS C.QQ D.F0 C.TS C.TR C.SR C.QQ D.F4 C.TS C.TR C.QI D.E1 D.70 C.II C.IH C.SR C.QH D.D3 D.65 D.38 C.RS D.C6 C.RR D.B6 C.QQ D.FC C.TS D.50 C.II C.TR D.77 D.2C D.55 D.E4 C.JK C.HQ D.AA C.HQ D.A1 C.TT C.QH C.RR D.B0 C.TT C.IH C.SR C.QQ D.FD D.7E C.HI D.9B D.47 D.29 D.12 C.HH D.8C D.DD D.6E C.HI D.93 D.45 C.JK C.RS D.C4 C.TS C.TR C.QI D.E2 C.TR C.QQ D.F6 C.HQ D.A9 D.52 C.HI D.9C C.TT C.QH D.DF C.SR D.28 C.RR D.BA D.6F D.3B D.17 D.0D D.0A C.HH D.85 D.48 C.II C.RS D.C8 C.TS C.QH D.D8 C.TS C.QH D.DA C.RR D.BD D.5E C.HI D.9F D.4F D.2B D.13 D.05 D.08 C.JK C.RS D.CC C.TS C.QH D.D9 D.66 C.HI D.92 C.HQ D.AC C.TT C.QH D.D5 D.6C C.II C.RS D.C1 D.60 C.II C.IH C.SR C.SS C.II C.SS C.SS C.QQ D.F1 D.74 C.II C.IH C.QI D.E5 D.78 C.RS D.C2 C.RR D.B4 C.TT C.TR C.QI D.E9 D.72 C.HI D.98 C.TT C.QH D.DE C.RR D.BF D.5F D.2F D.1B D.07 D.09 D.02 C.HH D.84 D.54 C.II C.IH C.QI D.E7 D.79 D.36 D.5C C.II C.RS D.CB D.63 D.31 D.49 D.22 C.HH D.80 C.TT C.HI D.9D D.4E C.HI D.97 C.RR D.B9 D.56 C.HI D.9E C.HQ D.AO C.TT C.TR C.TT C.TR C.QI D.EA C.RR D.B1 C.HH D.8A C.HQ D.A5 D.58 C.II C.RS D.CA C.RR D.B5 D.14 C.JK C.IH C.QI D.EF D.7B D.37 D.1D D.0E C.TR C.SR C.SS C.QQ D.F9 D.76 C.HI D.9A C.HQ D.AD D.4D D.2A C.HH D.81 D.40 C.II C.IH C.SR C.SS C.HQ D.AF D.5B D.19 D.06 C.HH D.86 D.27 C.SR C.SS C.SS C.QQ D.F2 D.18 C.JK C.RS D.CE C.SS C.QQ D.F3 C.RR D.B8 C.RR D.B7 D.5D C.HH D.87 D.5A C.QQ D.FA C.HQ D.A6 C.HQ D.A2 C.TT C.QH D.D6 C.RR D.BE C.HQ D.AB D.53 D.25 D.2E C.HH D.83 D.41 D.20 C.JK C.SR C.SS C.TT D.75 D.3C C.JK C.RS D.C7 D.69 D.32 C.HH D.88 C.QH D.DB D.67 D.39 D.16 C.HH D.8E C.HQ D.A7 D.59 D.26 C.TR C.QI D.E8 C.TS C.QH D.D0 C.TS C.TR C.SR D.30 C.JK C.IH C.SR C.QQ D.FE C.RR D.BB D.57 The Receive Control State Machine always operates synchronous to the recovered character clock (bit-clock/10 or bit-clock/12). When the Receive FIFO is bypassed, RXCLK becomes an output that changes synchronous to the internal character clock. RXCLK operates at the same frequency as the internal character clock. Document Number: 38-02020 Rev. *H C.IH C.QH D.DC C.TS C.HH D.82 C.HQ D.A4 C.TT C.QQ D.F5 D.7C C.RS D.C3 D.61 D.2D C.HH D.8D D.4A C.HI D.95 D.1A C.II Discard Policies When the Receive FIFO is enabled, the Receive Control State Machine has the ability to selectively discard specific characters from the data stream that are determined by the present configuration as being unnecessary. When discarding is enabled, it reduces the host system overhead necessary to keep the Receive FIFO from overflowing and losing data. Page 20 of 56 CY7C9689A The discard policy is configured as part of the operating mode and is set using the RXMODE[1:0] inputs. The four discard policies are listed in Table 5. Figure 4. External FIFO Depth Expansion of the CY7C9689A Receive Data Path) Table 5. Receiver Discard Policies Policy # 0 (00) Policy Description Keep all received characters 1 (01) Process Commands, discard all but the last JK or LM SYNC character 2 (1X) Process Commands, discard all C5.0 characters Policy 0 is the simplest and also applies for all conditions where the Receive FIFO is bypassed. In this mode, every character that is received is placed into the Receive FIFO (when enabled) or into the Receive Output Register. In discard policy 1, the JK or LM SYNC character, which is automatically transmitted when no data is present in the Transmit FIFO, is treated differently here. In this mode, whenever two or more adjacent JK or LM characters are received, all of them are discarded except the last one received before any other character type. This allows these fill characters to be removed from the data stream, but the last SYNC character which can be used as a delimiter. Policy 2 is identical to policy 1 except that all C5.0 characters are removed from the data stream. When the FIFOs are bypassed (FIFOBYP LOW), no characters are actually discarded, but the receiver discard policy can be used to control external filtering of the data. The RXEMPTY FIFO flag is used to indicate if the character on the output bus is valid or not. In discard policy 0, the RXEMPTY flag is always deasserted to indicate that valid data is always present. In discard policy 1, the RXEMPTY flag indicates an empty condition for all but the last JK or LM character before any other character is presented. In discard policy 2, the RXEMPTY flag indicates an empty condition for all JK or LM SYNC characters. When any other character is present, this flag indicates that valid or “interesting” Data or Special Characters are present. Receive FIFO The Receive FIFO is used to buffer data captured from the selected serial stream for later processing by the host system. This FIFO is sized to hold 256 14-bit characters. When the FIFO is enabled, it is written to by the Receive Control State Machine. When data is present in the Receive FIFO (as indicated by the RXFULL, RXHALF, and RXEMPTY Receive FIFO status flags), it can be read from the Output Register by asserting CE and RXEN. The read port on the Receive FIFO may be configured for the same two timing models as the transmit interface: UTOPIA and Cascade. Both are forms of a FIFO interface. The UTOPIA timing model has active LOW RXEMPTY and RXFULL status flags, and an active LOW RXEN enable. When configured for Cascade operation, these same signals are all active HIGH. Either timing model supports connection to various host bus interfaces, state machines, or external FIFOs for depth expansion (see Figure 4) Document Number: 38-02020 Rev. *H CY7C42x5 FIFO EF* REN* Q RXCLK EF* REN* RXEN FF* RXEMPTY WEN* Q RCLK CY7C9689A RXDATA RXSC/D D RXCLK WCLK “1” EXTFIFO The Receive FIFO presents Full, Half-Full, and Empty FIFO status flags. These flags are provided synchronous to RXCLK to allow operation with a Moore-type external controlling state machine. When configured with the Receive FIFO enabled, RXCLK is an input. When the Receive FIFO is bypassed (FIFOBYP is LOW), RXCLK is an output operating at the received character rate. Receive Input Register The input register is clocked by the rising edge of RXCLK. It samples numerous signals that control the reading of the Receive FIFO and operation of the Receive Control State Machine. Receive Output Register The Receive Output Register changes in response to the rising edge of RXCLK. The Receive FIFO status flag outputs of this register are placed in a High-Z state when the CY7C9689A is not addressed (CE is sampled HIGH). The RXDATA bus output drivers are enabled when the device is selected by RXEN being asserted in the RXCLK cycle immediately following that in which the device was addressed (CE is sampled LOW), and RXEN being sampled by RXCLK. This initiates a Receive FIFO read cycle. Just as with the TXDATA bus on the Transmit Input Register, the receive outputs are also mapped by the specific decoding and bus-width selected by the ENCBYP, BYTE8/10 and FIFOBYP inputs. These assignments are shown in Table 6. If the Receive FIFO and Decoder are bypassed, all received characters are passed directly to the Receive Output Register. If framing is enabled, and JK or LM sync characters have been detected meeting the present framing requirements, the output characters will appear on proper character boundaries. If framing is disabled (RFEN is LOW) or sync characters have not been detected in the data stream, the received characters may not be output on their proper 10-bit boundaries. In this mode, some form of external framing and decoding/descrambling must be used to recover the original source data. Page 21 of 56 CY7C9689A Table 6. Receiver Output Bus Signal Map Receiver Decoder Mode[1] RXDATA Bus Output Bit Encoded 8-bit Character Stream[8] Pre-encoded 10-bit Character Stream Encoded 10-bit Character Stream[9] Pre-encoded 12-bit Character Stream RXSC/D RXSC/D RXDATA[0] RXDATA[0] RXD[0][10, 11] RXDATA[0] RXD[0][10, 12] RXDATA[1] RXDATA[1] RXD[1] RXDATA[1] RXD[1] RXDATA[2] RXDATA[2] RXD[2] RXDATA[2] RXD[2] RXDATA[3] RXDATA[3] RXD[3] RXDATA[3] RXD[3] RXDATA[4] RXDATA[4] RXD[4] RXDATA[4] RXD[4] RXDATA[5] RXDATA[5] RXD[5] RXDATA[5] RXD[5] RXDATA[6] RXDATA[6] RXD[6] RXDATA[6] RXD[6] RXDATA[7] RXDATA[7] RXD[7] RXDATA[7] RXD[7] RXDATA[8]/RXCMD[3] RXCMD[3] RXD[8] RXDATA[8] RXD[8] RXD[9] RXDATA[9][9] RXD[9] RXSC/D RXDATA[9]/RXCMD[2] RXCMD[2] RXCMD[1] RXCMD[1] RXCMD[1] RXD[10][12] RXCMD[0] RXCMD[0] RXCMD[0] RXD[11] VLTN VLTN VLTN Notes 8. When BYTE8/10 is HIGH, received bit order is decoded form the serial stream and presented (MSB to LSB) at RXDATA[7,6,5,4] and RXDATA[3,2,1,0] or RXCMD[3,2,1,0] as indicated by RXSC/D. 9. When BYTE8/10 is LOW, received bit order is decoded form the serial stream and presented (MSB to LSB) at RXDATA[8,7,6,5,4] and RXDATA[9,3,2,1,0] or RXCMD[1,0] as indicated by RXSC/D. 10. First bit shifted into the receiver. 11. When ENCBYP is LOW and BYTE8/10 is HIGH, the received bit order is (LSB to MSB) RXD[0,1,2,3,4,5,6,7,8,9]. 12. When ENCBYP is LOW and BYTE8/10 is LOW, the received bit order is (LSB to MSB) RXD[0,1,2,3,4,5,6,7,8,9,11,10]. Document Number: 38-02020 Rev. *H Page 22 of 56 CY7C9689A Maximum Ratings Static discharge voltage........................................... > 2001 V (per MIL-STD-883, Method 3015) (Above which the useful life may be impaired. For user guidelines, not tested.) Storage temperature ................................ –65 °C to +150 °C Ambient temperature with (power applied)–55 °C to +125 °C Supply voltage to ground potential ................–0.5 v to +6.5 v DC voltage applied to outputs............... –0.5 v to VDD + 0.5 v Output current into TTL outputs (LOW) ....................... 30 mA Latch-up current ..................................................... > 200 mA Operating Range Range Ambient Temperature VDD 0 C to +70 C 5.0 V 10% –40 C to +85 C 5.0 V 10% Commercial Industrial DC input voltage ................................... –0.5 v to VDD + 0.5 v CY7C9689A DC Electrical Characteristics Over the Operating Range Parameter Description Test Conditions Min. Max. Unit 2.4 – V TTL Outputs IOH = 2 mA, VDD = Min. VOHT Output HIGH voltage VOLT Output LOW voltage IOL = 8 mA, VDD = Min. IOST Output short circuit current VOUT = 0 V[13] IOZL High-Z output leakage current – 0.4 V –30 80 mA –20 20 mA TTL Inputs VIHT Input HIGH voltage 2.0 VCC V VILT Input LOW voltage –0.5 0.8 V IIHT Input HIGH current VIN = VDD – ±40 A IILT Input LOW current VIN = 0.0 V – 40 A IILPDT Input HIGH current with internal pull-down VIN = VCC – +300 A IILPUT Input LOW current with internal pull-up VIN = 0.0 V –300 – A Transmitter PECL-Compatible Output Pins: OUTA+, OUTA, OUTB+, OUTB VOHE Output HIGH voltage (VDD referenced) Load = 50 to VDD 1.33 v; RCURSET = 10 k VDD 1.03 VDD 0.83 V VOLE Output LOW voltage (VDD referenced) Load = 50 to VDD 1.33 v; RCURSET = 10 k VDD 2.0 VDD 1.62 V VODIF Output differential voltage |(OUT+) (OUT)| Load = 50 to VDD 1.33 v; RCURSET = 10 k 600 1100 mV Receiver Single-ended PECL-Compatible Input Pin: CARDET VIHE Input HIGH voltage (VDD referenced) VDD 1.165 VDD V VILE Input LOW voltage (VDD referenced) 2.5 VDD 1.475 V IIHE Input HIGH current VIN = VIHE(min.) – +40 IILE Input LOW current VIN = VILE(max.) –40 A A Receiver Differential Line Receiver Input Pins: INA+, INA, INB+, INB VDIFF Input differential voltage |(IN+) (IN)| 200 2500 mV VIHH Highest input HIGH voltage – VDD V VILL Lowest input LOW voltage 2.5 – V IIHH Input HIGH current VIN = VIHH Max. – 750 A IILL[14] Input LOW current VIN = VILL Min. 200 – A Notes 13. Tested one output at a time, output shorted for less than one second, less than 10% duty cycle. 14. To guarantee positive currents for all PECL voltages, an external pull-down resistor must be present. Document Number: 38-02020 Rev. *H Page 23 of 56 CY7C9689A CY7C9689A DC Electrical Characteristics (continued) Over the Operating Range Parameter Description Test Conditions Miscellaneous IDD[15] Power supply current Freq. = Max. Commercial Min. Max. Typ. Max. 170 250 Unit mA Capacitance[16] Parameter Description Test Conditions Max. Unit CINTTL TTL input capacitance TA = 25 C, f0 = 1 MHz, VDD = 5.0 V 7 pF CINPECL PECL input capacitance TA = 25 C, f0 = 1 MHz, VDD = 5.0 V 4 pF AC Test Loads and Waveforms 5.0 V R1 OUTPUT R1=500 R2=333 CL 10 pF (Includes fixture and probe capacitance) VDD – 1.3 CL CL R2 (a) TTL AC Test Load Vth=1.5 v 0.0 V [17] 3.0 V 3.0 V RL 2.0 V 0.8 v (b) PECL AC Test Load 0.8 v < 1 ns (c) TTL Input Test Waveform 80% Vth=1.5 v VILE < 1 ns [17] VIHE VIHE 2.0 V RL =50 CL < 5 pF (Includes fixture and probe capacitance) 80% 20% 250 ps 20% VILE 250 ps (d) PECL Input Test Waveform Notes 15. Maximum ICC is measured with VDD = MAX, RFEN = LOW, and outputs unloaded. Typical IDD is measured with VDD = 5.0 V, TA = 25 °C, RFEN = LOW, and outputs unloaded. 16. Tested initially and after any design or process changes that may affect these parameters, but not 100% tested. 17. Cypress uses constant current (ATE) load configurations and forcing functions. This figure is for reference only. Document Number: 38-02020 Rev. *H Page 24 of 56 CY7C9689A CY7C9689A Transmitter TTL Switching Characteristics, FIFO Enabled Over the Operating Range Parameter Description Min. Max. Unit 50 MHz – ns fTS TXCLK clock cycle frequency with transmit FIFO enabled tTXCLK TXCLK period tTXCPWH TXCLK HIGH time 6.5 – ns tTXCPWL TXCLK LOW time 6.5 – ns tTXCLKR[16] TXCLK Rise time[18] 0.7 5 ns tTXCLKF[16] TXCLK fall time[18] 0.7 5 ns 20 tTXA Flag access time from TXCLKto Output 2 15 ns tTXDS Transmit data set-up time toTXCLK 4 – ns tTXDH Transmit data hold time from TXCLK 1 – ns tTXENS Transmit enable set-up time toTXCLK 4 – ns tTXENH Transmit enable hold time fromTXCLK 1 – ns tTXRSS Transmit FIFO Reset (TXRST) set-up time toTXCLK 4 – ns tTXRSH Transmit FIFO Reset (TXRST hold time fromTXCLK 1 – ns tTXCES Transmit chip enable (CE) set-up time toTXCLK 4 – ns tTXCEH Transmit chip enable (CE) hold time fromTXCLK 1 – ns tTXZA Sample of CE LOW by TXCLK, output high-Z to Active HIGH or LOW 0 – ns tTXOE Sample of CE LOW by TXCLKto output valid 1.5 20 ns tTXAZ Sample of CE HIGH by TXCLKto output in high-Z 1.5 20 ns Notes 18. Input/output rise and fall time is measured between 0.8 V and 2.0 V. 19. Parallel data output specifications are only valid if all outputs are loaded with similar DC and AC loads. Document Number: 38-02020 Rev. *H Page 25 of 56 CY7C9689A CY7C9689A Receiver TTL Switching Characteristics, FIFO Enabled Over the Operating Range Parameter Description Min. Max. Unit 50 MHz fRIS RXCLK clock cycle frequency with receive FIFO enabled tRXCLKIP RXCLK input period tRXCPWH RXCLK input HIGH time 6.5 ns tRXCPWL RXCLK input LOW time 6.5 ns tRXCLKIR[16] RXCLK input Rise time[20] 0.7 5 ns tRXCLKIF[16] RXCLK input Fall time[20] 0.7 5 ns 20 ns tRXENS Receive enable set-up time toRXCLK 4 ns tRXENH Receive enable hold time fromRXCLK 1 ns tRXRSS Receive FIFO reset (RXRXT) set-up time toRXCLK 4 ns tRXRSH Receive FIFO reset (RXRXT) hold time fromRXCLK 1 ns tRXCES Receive chip enable (CE) set-up time toRXCLK 4 ns tRXCEH Receive chip enable (CE) Hold Time fromRXCLK 1 ns tRXA Flag and data access time from RXCLKto output 1.5 tRXZA Sample of CE LOW by RXCLK, Output High-Z to Active HIGH or LOW,[21] or Sample of RXEN Asserted by RXCLK, Output High-Z to Active HIGH or LOW tRXOE Sample of CE LOW by RXCLK to Output Valid,[21] or Sample of RXEN Asserted by RXCLKto RXDATA Outputs Valid 1.5 20 ns tRXZA Sample of CE HIGH by RXCLK to Output in High-Z,[21] or Sample of RXEN Asserted by RXCLKto RXDATA Outputs in High-Z 1.5 20 ns 15 0 ns ns CY7C9689A Transmitter TTL Switching Characteristics, FIFO Bypassed Over the Operating Range Min. Max. Unit tTRA Parameter Flag access time from REFCLKto output Description 2 15 ns tREFDS Write data set-up time to REFCLK 4 ns tREFDH Write data hold time from REFCLK 2 ns tREFENS Transmit enable set-up time toREFCLK 4 ns tREFENH Transmit enable hold time fromREFCLK 2 ns tREFCES Transmit chip enable (CE) set-up time toREFCLK 4 ns tREFCEH Transmit chip enable (CE) hold time fromREFCLK 2 ns tREFZA Sample of CE LOW by REFCLK, output High-Z to Active HIGH or LOW tREFOE Sample of CE LOW by REFCLK to flag output Valid 1.5 20 ns tREFAZ Sample of CE HIGH by REFCLK to flag output High-Z 1.5 20 ns 0 ns Notes 20. Input/output rise and fall time is measured between 0.8 V and 2.0 V. 21. Parallel data output specifications are only valid if all outputs are loaded with similar DC and AC loads. Document Number: 38-02020 Rev. *H Page 26 of 56 CY7C9689A CY7C9689A Receiver TTL Switching Characteristics, FIFO Bypassed Over the Operating Range Parameter fROS[22] Min. Max. Unit RXCLK clock output frequency—100 to 200 MBaud 8-bit Operation (SPDSEL is HIGH and BYTE8/10 is HIGH) Description 10 20 MHz RXCLK clock output frequency—50 to 100 MBaud 8-bit Operation (SPDSEL is LOW and BYTE8/10 is HIGH) 5 10 MHz RXCLK clock output frequency—100 to 200 MBaud 10-bit Operation (SPDSEL is HIGH and BYTE8/10 is LOW) 8.33 16.67 MHz RXCLK clock output frequency—50 to 100 MBaud 10-bit Operation (SPDSEL is LOW and BYTE8/10 is LOW) 4.16 8.33 MHz 25 240 ns tRXCLKOP RXCLK output period tRXCLKOD RXCLK output duty cycle 40 60 % tRXCLKOR[16] RXCLK output rise time[18] 0.25 2 ns tRXCLKOF[16] RXCLK output fall time[18] 0.25 2 ns tRXENS Receive enable set-up time toRXCLK 4 ns tRXENH Receive enable hold time fromRXCLK 1 ns tRXZA Sample of CE LOW by RXCLK, Outputs High-Z to Active Sample of RXEN Asserted by RXCLK to RXDATA Outputs High-Z to Active 0 ns tRXOE Sample of CE LOW by RXCLK to Flag Output Valid Sample of RXEN Asserted by RXCLK to RXDATA Output Low-Z 1.5 20 ns tRXAZ Sample of CE HIGH by RXCLK to Flag Output High-Z Sample of RXEN Deasserted by RXCLK to RXDATA Output High-Z 1.5 20 ns Note 22. The period of tROS will match the period of the transmitter PLL reference (REFCLK) when receiving serial data. When data is interrupted, RXCLK may drift to REFCLK +0.2%. Document Number: 38-02020 Rev. *H Page 27 of 56 CY7C9689A CY7C9689A REFCLK Input Switching Characteristics Over the Operating Range Parameter fREF Conditions Description Min. Max. Unit 0 8.33 16.67 MHz 0 1 10 20 MHz 0 1[18] 0 16.67 33.3 MHz REFCLK clock frequency—50 to 100 MBaud, 8-bit Mode, REFCLK = 4x Character Rate 0 1[18] 1 20 40 MHz REFCLK clock frequency—100 to 200 MBaud, 10-bit Mode, REFCLK = Character Rate 1 0 0 8.33 16.67 MHz REFCLK clock frequency—100 to 200 MBaud, 8-bit Mode, REFCLK = Character Rate 1 0 1 10 20 MHz REFCLK clock frequency—100 to 200 MBaud, 10-bit Mode, REFCLK = 2x Character Rate 1 1 0 16.67 33.3 MHz REFCLK clock frequency—100 to 200 MBaud, 8-bit Mode, REFCLK = 2x Character Rate 1 1 1 20 40 MHz 120 ns SPDSEL RANGESEL BYTE8/10 REFCLK clock frequency—50 to 100 MBaud, 10-bit Mode, REFCLK = 2x Character Rate 0 0 REFCLK clock frequency—50 to 100 MBaud, 8-bit Mode, REFCLK = 2x Character Rate 0 REFCLK clock frequency—50 to 100 MBaud, 10-bit Mode, REFCLK = 4x Character Rate tREFCLK REFCLK period 25 tREFH REFCLK HIGH time 6.5 tREFL REFCLK LOW time tREFRX REFCLK frequency referenced to received clock period[24] ns 6.5 0.04 ns +0.04 % CY7C9689A Receiver Switching Characteristics Over the Operating Range Parameter tB[25] Description Bit time Max. Unit 20.0 5.0 ns 600 ps alignment[16, 26] tSA Static tEFW Error free window[16, 27, 28] tIN_J Min. IN± peak-to-peak input jitter 0.65 tolerance[16, 27, 29, 30] UI 0.5 UI Notes 23. When configured for synchronous operation with the FIFOs bypassed (FIFOBYP is LOW), if RANGESEL is HIGH the SPDSEL input is ignored and operation is forced to the 100–200 MBaud range. 24. REFCLK has no phase or frequency relationship with RXCLK and only acts as a centering reference to reduce clock synchronization time. REFCLK must be within 0.04% of the transmitter PLL reference (REFCLK) frequency, necessitating a 200-PPM crystal. 25. The PECL switching threshold is the midpoint between the PECL VOH, and VOL specification (approximately VDD 1.33 v). 26. Static alignment is a measure of the alignment of the Receiver sampling point to the center of a bit. Static alignment is measured by the absolute difference of the left and right edge shifts (|tSH_L – tSH_R|) of one bit until a character error occurs. 27. Receiver UI (Unit Interval) is calculated as 1/(fREF*N) when operated in 8-bit mode (N = 10) and 10-bit mode (N = 12) if no data is being received, or 1/(fREF*N) of the remote transmitter if data is being received. In an operating link this is equivalent to N * tB when REFCLK = 1X the character rate. An alternate multiply ratios (2X or 4X, as selected by SPDSEL and RANGESEL), the numerator is multiplied by 2 or 4 respectively. 28. Error Free Window is a measure of the time window between bit centers where a transition may occur without causing a bit sampling error. EFW is measured over the operating range, input jitter 50% Dj. 29. The specification is sum of 25% Duty Cycle Distortion (DCD), 10% Data Dependant Jitter (DDJ), 15% Random Jitter (RJ). 30. Parallel data output specifications are only valid if all outputs are loaded with similar DC and AC loads. Document Number: 38-02020 Rev. *H Page 28 of 56 CY7C9689A CY7C9689A Transmitter Switching Characteristics Over the Operating Range Parameter tB[25] Description Bit time [16] tRISE PECL output rise time 2080% (PECL Test Load) tFALL PECL output fall time 8020% (PECL Test Load)[16] Min. Max. Unit 20.0 5.0 ns 200 1700 ps 200 1700 ps [16, 31] tDJ Deterministic jitter (peak-peak) 0.02 UI tRJ Random jitter () [16, 32] 0.008 UI tJT Transmitter total output jitter (peak-peak)[16] 0.08 UI CY7C9689A HOTLink Transmitter Switching Waveforms Write Cycle Asynchronous (FIFO) Interface EXTFIFO = HIGH tTXCLK FIFOBYP = HIGH tTXCPWH tTXCPWL TXCLK tTXDS TXHALT TXSC/D TXDATA[7:0] TXDATA[9:8]/TXCMD[2:3] TXCMD[1:0] tTXDH Note 33 tTXENH NO OPERATION TXEN tTXENS tTXA TXFULL TXHALF TXEMPTY Document Number: 38-02020 Rev. *H tTXA Page 29 of 56 CY7C9689A CY7C9689A HOTLink Transmitter Switching Waveforms (continued) Notes 31. While sending continuous JK, outputs loaded to 50 to VDD 1.3 v, over the operating range. 32. While sending continuous HH, after 100,000 samples measured at the cross point of differential outputs, time referenced to REFCLK input, over the operating range. 33. When EXTFIFO is HIGH, the write data is captured on the clock cycle following TXEN = HIGH. Write Cycle Asynchronous (FIFO) Interface EXTFIFO = LOW FIFOBYP = HIGH TXCLK tTXDS TXHALT TXSC/D TXDATA[7:0] TXDATA[9:8]/TXCMD[2:3] TXCMD[1:0] tTXDH Note 34 tTXENS tTXENH TXEN NO OPERATION tTXA TXFULL TXHALF TXEMPTY Document Number: 38-02020 Rev. *H tTXA Page 30 of 56 CY7C9689A CY7C9689A HOTLink Transmitter Switching Waveforms (continued) OUTPUT ENABLE Timing Asynchronous (FIFO) Interface EXTFIFO = HIGH FIFOBYP = HIGH TXCLK TXHALT TXSC/D TXDATA[7:0] TXDATA[9:8]/TXCMD[2:3] TXCMD[1:0] NO OPERATION TXEN Note 35 tTXRSS tTXRSH TXRST tTXCES tTXCEH CE tTXOE tTXOAZ TXFULL TXHALF TXEMPTY tTXOZA Notes 34. Illustrates timing only. TXEN and TXRST not usually active in same time period. 35. When transferring data to the Transmitter input from a depth expanded external FIFO, the data is captured from the external FIFO one clock cycle following the actual enable (TXEN = HIGH). Document Number: 38-02020 Rev. *H Page 31 of 56 CY7C9689A CY7C9689A HOTLink Transmitter Switching Waveforms (continued) OUTPUT ENABLE Timing Asynchronous (FIFO) Interface EXTFIFO = LOW FIFOBYP = HIGH TXCLK TXHALT TXSC/D TXDATA[7:0] TXDATA[9:8]/TXCMD[2:3] TXCMD[1:0] TXEN NO OPERATION tTXRSS CE TXRST tTXRSH Note 34 tTXCES tTXCEH CE TXRST tTXOE tTXOAZ TXFULL TXHALF TXEMPTY tTXOZA Write Cycle Synchronous Interface EXTFIFO = HIGH FIFOBYP = LOW tREFCLK tREFH tREFL REFCLK tREFDS TXHALT TXSC/D TXDATA[7:0] TXDATA[9:8]/TXCMD[2:3] TXCMD[1:0] tREFDH Note 36 tREFENH NO OPERATION TXEN tREFENS tTRA TXFULL TXHALF TXEMPTY tTRA Note 36. \When transferring data to the Transmitter input from a synchronous external controller, the data is captured in the same clock cycle as the actual enable (TXEN = LOW). Document Number: 38-02020 Rev. *H Page 32 of 56 CY7C9689A CY7C9689A HOTLink Transmitter Switching Waveforms (continued) Write Cycle Synchronous Interface EXTFIFO = LOW FIFOBYP = LOW REFCLK tREFDS TXHALT TXSC/D TXDATA[7:0] XDATA[9:8]/TXCMD[2:3] TXCMD[1:0] tREFDH Note 37 tREFENS tREFENH TXEN NO OPERATION tTRA TXFULL TXHALF TXEMPTY OUTPUT ENABLE Timing Synchronous Interface EXTFIFO = HIGH FIFOBYP = LOW REFCLK TXHALT TXSC/D TXDATA[7:0] TXDATA[9:8]/TXCMD[2:3] TXCMD[1:0] TXEN tREFENH NO OPERATION tREFENS tREFCES tREFCEH CE tREFOE tREFAZ TXFULL TXEMPTY tREFZA Note 37. On inhibited reads, or if the Receive FIFO goes empty, the data outputs do not change. Document Number: 38-02020 Rev. *H Page 33 of 56 CY7C9689A CY7C9689A HOTLink Transmitter Switching Waveforms (continued) OUTPUT ENABLE Timing Synchronous Interface EXTFIFO = LOW FIFOBYP = LOW REFCLK TXHALT TXSC/D TXDATA[7:0] TXDATA[9:8]/TXCMD[2:3] TXCMD[1:0] TXEN NO OPERATION CE TXFULL TXEMPTY Document Number: 38-02020 Rev. *H Page 34 of 56 CY7C9689A CY7C9689A HOTLink Receiver Switching Waveforms Read Cycle Asynchronous (FIFO) Interface EXTFIFO = HIGH FIFOBYP = HIGH tRXCLKOP tRXCLKIP tRXCLKOD tRXCPWH tRXCLKOD tRXCPWL RXCLK tRXENH tRXENS RXEN NO OPERATION READ READ tRXA tRXA RXEMPTY Note 38 FIFO EMPTY RXFULL RXHALF RXDATA[7:0] RXDATA[9:8/RXCMD[2:3] RXCMD[1:0] VALID DATA Note 39 CE Read Cycle Asynchronous (FIFO) Interface EXTFIFO = LOW FIFOBYP = HIGH RXCLK tRXENS RXEN tRXENH READ tRXA tRXA FIFO EMPTY RXEMPTY RXFULL RXHALF RXDATA[7:0] RXDATA[9:8/RXCMD[2:3] RXCMD[1:0] VALID DATA Note 40 CE Notes 38. When reading data from synchronous data interface, the data is captured on any clock cycle that RXEN = LOW. RXEMPTY = HIGH indicates data is available. RXEMPTY = LOW indicates that the FIFO is empty. 39. Illustrates timing only. RXEN and RXRST not usually active in same time period. 40. Receive FIFO Reads are inhibited while the outputs are High-Z. Document Number: 38-02020 Rev. *H Page 35 of 56 CY7C9689A CY7C9689A HOTLink Receiver Switching Waveforms (continued) Output Enable Timing RXCLK tRXENH tRXENS RXEN NO OPERATION Note 41 tRXRSH tRXRSS RXRST tRXCES tRXCEH CE tRXAZ tRXOE RXFULL RXDATA[7:0] RXDATA[9:8/RXCMD[2:3] RXCMD[1:0] Note 42 OLD DATA tRXZA tREFCLK tREFL tREFH REFCLK Static Alignment Error-Free Window tB/2 tSA tB/2 tSA tEFW INA INB INA INB tB BIT CENTER SAMPLE WINDOW BIT CENTER Table 7. HOTLink TAXI-compatible Encoder Patterns 4B/5B Encoder 5B/6B Encoder HEX Data 4-bit Binary Data[43] 5-bit Encoded Symbol[44, 45] HEX Data 5-bit Binary Data[43] 6-bit Encoded Symbol[44, 45] 0 0000 11110 00 00000 110110 1 0001 01001 01 00001 010001 Notes 41. Binary Input Data is the parallel input data which is input to the Transmitter and output from the Receiver. Binary bits are listed from left to right in the following order: 8-Bit mode (BYTE8/10 is HIGH and TXSC/D or RXSC/D is LOW)—TXDATA/RXDATA[7], [6], [5], [4], and TXDATA/RXDATA[3], [2], [1], [0]; 10-Bit mode (BYTE8/10 is LOW and TXSC/D or RXSC/D is LOW)—TXDATA/RXDATA[8], [7], [6], [5], [4], and TXDATA/RXDATA[9], [3], [2], [1], [0]. 42. The ENCODED Symbols are shown here as “ones and zeros”, but are converted to and from an NRZI stream at the transmitter output and receiver input. NRZI represents a “one” as a state transition (either LOW-to-HIGH or HIGH-to-LOW) and a “zero” as no transition within the bit interval. 43. Encoded Serial Symbol bits are shifted out with the most significant bit (Left-most) of the most significant nibble coming out first. 44. Binary CMD is the parallel input data which is input to the Transmitter and output from the Receiver. Binary bits are listed from left to right in the following order: 8-Bit mode (BYTE8/10 is HIGH and TXSC/D or RXSC/D is HIGH)—TXCMD/RXCMD[3], [2], [1], [0]; 10-Bit mode (BYTE8/10 is LOW and TXSC/D or RXSC/D is HIGH)—TXCMD/RXCMD[1], [0]. 45. While these Commands are legal data and will not disrupt normal operation if used occasionally, they may cause data errors if grouped into recurrent fields. Normal PLL operation cannot be guaranteed if one or more of these commands is continuously repeated. Document Number: 38-02020 Rev. *H Page 36 of 56 CY7C9689A Table 7. HOTLink TAXI-compatible Encoder Patterns (continued) 4B/5B Encoder 5B/6B Encoder HEX Data 4-bit Binary Data[43] 5-bit Encoded Symbol[44, 45] HEX Data 5-bit Binary Data[43] 6-bit Encoded Symbol[44, 45] 2 0010 10100 02 00010 100100 3 0011 10101 03 00011 100101 4 0100 01010 04 00100 010010 5 0101 01011 05 00101 010011 6 0110 01110 06 00110 010110 7 0111 01111 07 00111 010111 8 1000 10010 08 01000 100010 9 1001 10011 09 01001 110001 A 1010 10110 0A 01010 110111 B 1011 10111 0B 01011 100111 C 1100 11010 0C 01100 110010 D 1101 11011 0D 01101 110011 E 1110 11100 0E 01110 110100 F 1111 11101 0F 01111 110101 – – – 10 10000 111110 – – – 11 10001 011001 – – – 12 10010 101001 – – – 13 10011 101101 – – – 14 10100 011010 – – – 15 10101 011011 – – – 16 10110 011110 – – – 17 10111 011111 – – – 18 10001 101010 – – – 19 11001 101011 – – – 1A 11010 101110 – – – 1B 11011 101111 – – – 1C 11100 111010 – – – 1D 11101 111011 – – – 1E 11110 111100 – – – 1F 11111 111101 Table 8. HOTLink TAXI Compatible Command Symbols CY7C9689A (Transmitter) CY7C9689A (Receiver) Command Input TXCMD[3:0] Command Output RXCMD[3:0] HEX Binary CMD[46] Encoded Symbol[44, 45] Mnemonic HEX Binary CMD[46] 11000 10001 JK (8-bit SYNC) 0 0000 8-bit mode (BYTE8/10 is HIGH) 0 0000 Note 46. Signals labeled in italics are internal to the CY7C9689A. Document Number: 38-02020 Rev. *H Page 37 of 56 CY7C9689A Table 8. HOTLink TAXI Compatible Command Symbols (continued) CY7C9689A (Transmitter) CY7C9689A (Receiver) Command Input TXCMD[3:0] Command Output RXCMD[3:0] 1 0001 11111 11111 II 1 0001 2 0010 01101 01101 TT 2 0010 3 0011 01101 11001 TS 3 0011 4 0100 11111 00100 IH 4 0100 5 0101 01101 00111 TR 5 0101 6 0110 11001 00111 SR 6 0110 7 0111 11001 11001 SS 7 0111 8[47] 1000 00100 00100 HH 8 1000 9[47] 1001 00100 11111 HI 9 1001 A[47] 1010 00100 00000 HQ A 1010 B 1011 00111 00111 RR B 1011 C 1100 00111 11001 RS C 1100 D[47] 1101 00000 00100 QH D 1101 E[47] 1110 00000 11111 QI E 1110 F[47] 1111 00000 00000 QQ F 1111 10-bit mode (BYTE8/10 is LOW) 0 00 011000 100011 LM (10-bit SYNC) 0 00 1 01 111111 111111 I’I’ 1 01 2 10 011101 011101 T’T’ 2 10 3 11 011101 111001 T’S’ 3 11 Functional Description The interconnection of two or more CY7C9689A Transceivers forms a general-purpose communications subsystem capable of transporting user data at up to 20 MBytes per second over several types of serial interface media. The CY7C9689A is highly configurable with multiple modes of operation. In the transmit section of the CY7C9689A, data moves from the input register, through the Transmit FIFO, to the 4B/5B Encoder. The encoded data is then shifted serially out the OUTx± differential PECL compatible drivers. The bit-rate clock is generated internally from a 2.5x, 5x, or 10x PLL clock multiplier. A more complete description is found in the section CY7C9689A HOTLink Transmit-Path Operating Mode Description. In the receive section of the CY7C9689A, serial data is sampled by the receiver on one of the INx± differential line receiver inputs. The receiver clock and data recovery PLL locks onto the selected serial bit stream and generates an internal bit-rate sample clock. The bit stream is deserialized, decoded, and presented to the Receive FIFO, along with a character clock. The data in the FIFO can then be read either slower or faster than the incoming character rate. A more complete description is found in the section CY7C9689A HOTLink Receive-Path Operating Mode Description. The Transmitter and Receiver parallel interface timing and functionality can be configured to Cascade directly to external FIFOs for depth expansion, couple directly to registers, or couple directly to state machines. These interfaces can accept or output either: ■ 8-bit characters ■ 10-bit characters ■ 10-bit pre-encoded characters (pre-scrambled or pre-encoded) ■ 12-bit pre-encoded characters (pre-scrambled or pre-encoded). The bit numbering and content of the parallel transmit interface is shown in Table 1. When operated with the 4B/5B, 5B/6B Encoder bypassed, the TXSC/D and RXSC/D bits are ignored. The HOTLink Transceiver serial interface provides a seamless interface to various types of media. A minimal number of external passive components are required to properly terminate transmission lines and provide LVPECL loads. For power supply decoupling, a single capacitor (in the range of 0.02 F to 0.1 F) is required per power/ground pair. Additional information on interfacing these components to various media can be found in the HOTLink Design Considerations application note. Note 47. Signals shown as dotted lines represent the differences in timing and active state of signals when operated in Cascade Timing. Document Number: 38-02020 Rev. *H Page 38 of 56 CY7C9689A CY7C9689A TAXI HOTLink Transmit-Path Operating Mode Descriptions at every rising edge of the REFCLK (along with TXEN) to maintain the data stream. If TXEN is not asserted, the Serializer is loaded with JK or LM sync characters. The TAXI HOTLink Transmitter can be configured into several operating modes, each providing different capabilities and fitting different transmission needs. These modes are selected using the FIFOBYP, ENCBYP and BYTE8/10 inputs on the CY7C9689A Transceiver. These modes can be reduced to five primary classes: In this mode the LSB of each input character (TXDATA[0]) is shifted out first, followed sequentially by TXDATA[1] through TXDATA[9] (TXDATA[11] when BYTE8/10 is LOW). ■ Synchronous Encoded ■ Synchronous Pre-encoded ■ Asynchronous Encoded ■ Asynchronous Pre-encoded. Synchronous Encoded In this mode, the Transmit FIFO is bypassed, while the 4B/5B, 5B/6B encoder is enabled. One character is accepted at the Transmit Input Register at the rising edge of REFCLK, and passed to the Encoder where it is encoded for serial transmission. The Serializer operates synchronous to REFCLK, which is multiplied by 10 or 5 to generate the serial data bit-clock. In this mode the TXRST and TXHALT inputs are not interpreted and may be tied either HIGH or LOW. To place the CY7C9689A into synchronous modes, FIFOBYP must be LOW. This mode is usually used for products that must meet specific predefined protocol requirements, and cannot tolerate the uncontrolled insertion of SYNC fill characters. The host system is required to provide new data at every rising edge of REFCLK (along with TXEN) to maintain the data stream. If TXEN is not asserted, the Encoder is loaded with JK or LM sync characters. Input Register Mapping In Encoded modes, the bits of the TXDATA input bus are mapped into characters (as shown in Table 1), including a TXSVS bit, eight bits of data, and a TXSC/D bit to select either Special Character codes or Data characters. The TXSC/D bit controls the encoding of the TXDATA[7:0] or TXDATA[9:0] bits of each character. It is used to identify if the input character represents a Data Character or a Special Character code. If TXSC/D is LOW, the character appeared on the TXDATA bus is encoded using the Data Character codes listed in Table 7. If TXSC/D is HIGH, the character on the TXCMD bus is encoded using the Special Character codes listed in Table 8. Synchronous Pre-encoded In synchronous pre-encoded mode, both the Transmit FIFO and the 4B/5B encoder are bypassed, and data passes directly from the Transmit Input Register to the Serializer. The Serializer operates synchronous to REFCLK, which is multiplied by 10 or 5 when BYTE8/10 is HIGH (as selected by the SPDSEL and RANGESEL inputs) to generate the serial data bit-clock. In this mode, part of the TXCMD bus inputs are used as part of the data input bus. To place the CY7C9689A into synchronous modes, FIFOBYP must be LOW. This mode is usually used for products containing external encoders or scramblers, that must meet specific protocol requirements. The host system is required to provide new data Document Number: 38-02020 Rev. *H Asynchronous Encoded In Asynchronous Encoded mode, both the Transmit FIFO and the Encoder are enabled. This provides 256 characters of data buffering. The Serializer operates synchronous to REFCLK, which is multiplied by 2.5, 5, or 10 to generate the serial data bit-clock (as selected by SPDSEL and RANGESEL). In this mode the TXRST and TXHALT inputs are interpreted. This mode supports the same Input Register mapping as Synchronous Encoded mode. Because both the Transmit FIFO and Encoder are enabled, the input FIFO may be loaded at any rate supported by the FIFO (up to 50 MHz), without generating any decoder errors at the receive end of the link. CY7C9689A TAXI HOTLink Receive-Path Operating Mode Descriptions The HOTLink Receiver can be configured into several operating modes, each providing different capabilities and fitting different reception needs. These modes are selected using the FIFOBYP, ENCBYP, BYTE8/10 inputs on the CY7C9689A Transceiver. These modes can be reduced to four primary classes: ■ Synchronous Decoded ■ Synchronous Undecoded ■ Asynchronous Decoded ■ Asynchronous Undecoded. In all these modes, serial data is received at one of the differential line receiver inputs and routed to the Deserializer and Framer. The PLL in the clock and data recovery block is used to extract a bit-rate clock from the transitions in the data stream, and uses that clock to capture bits from the serial stream. These bits are passed to the Deserializer where they are formed into 10- or 12-bit characters. To align the incoming bit stream to the proper character boundaries, the Framer must be enabled by asserting RFEN HIGH. The Framer logic-block checks the incoming bit stream for the unique pattern that defines the character boundaries. This logic filter looks for the JK or LM (when BYTE8/10 is LOW) sync character. Once a sync character is found, the Framer captures the offset of the data stream from the present character boundaries, and resets the boundary to reflect this new offset, thus framing the data to the correct character boundaries. Since noise induced errors can cause the incoming data to be corrupted, and since many combinations of corrupt and legal data can create an aliased sync character, the framer may also be disabled by deasserting RFEN LOW. Synchronous Decoded In these modes, the Receive FIFO is bypassed, while the 5B/4B, 6B/5B Decoder is enabled. Framed characters output from the Deserializer are decoded, and passed directly to the Receive Output Register. The Deserializer operates synchronous to the recovered bit-clock, which is divided by 10, generate the output Page 39 of 56 CY7C9689A RXCLK clock. In this mode the RXRST input is not interpreted and may be biased either HIGH or LOW. These modes are usually used for products that must meet specific protocol requirements. New decoded characters are provided at the RXDATA outputs once every rising edge of RXCLK. If RXEMPTY is asserted LOW, the characters on the RXCMD output register is a JK or LM sync character, and the discard policy is set to non-0. Because the decoder is now enabled, all received characters are checked for compliance to the 4B/5B decoding rules. Output Register Mapping The RXDATA[11:0] output bus is mapped into a character consisting of eight bits of data and four bits of command, or ten bits of data and two bits of command. An accompanying RXSC/D bit identifies the character as either command or data. The Violation (VLTN) output indicates a code violation has occurred. When the VLTN output is asserted HIGH, this indicates a transmission error is detected in the character at the current transfer clock cycle. Synchronous Undecoded In this mode, both the Receive FIFO and the 5B/4B, 6B/5B Decoder are bypassed, and data passes directly from the Deserializer to the output register. The Deserializer operates synchronous to the recovered bit-clock, which is divided by 10 to generate the output RXCLK clock. In this mode the RXRST input is not interpreted and may be biased either HIGH or LOW. This mode is usually used for products containing external decoders or descramblers that must meet specific protocol requirements. New data is provided at the RXDATA outputs once every rising edge of RXCLK. Received characters are not checked for any specific coding requirements and no decoding errors are reported. Asynchronous Decoded In Asynchronous Decoded mode, both the Receive FIFO and the Decoder of the CY7C9689A are enabled. The deserializer operates synchronous to the recovered bit-clock, which is divided by 10 to generate the Receive FIFO write clock. Characters are read from the Receive FIFO, using the external RXCLK input, when addressed by CE and selected by RXEN. In this mode the RXRST input is interpreted. Asynchronous Decoded mode supports the same Output Register mapping as the Synchronous Decoded mode. Because Document Number: 38-02020 Rev. *H both the Receive FIFO and Decoder are enabled, the output FIFO may be read at any rate supported by the FIFO, however, if the Receive FIFO ever indicates a full condition (RXFULL is asserted), data may be lost. Asynchronous Undecoded In Asynchronous Undecoded modes, the Receive FIFO is enabled. This means that all characters received from the serial interface are written to the Receive FIFO before being passed to the output register. The Deserializer operates synchronous to the recovered bit-clock, which is divided by 10 (or 12) to generate the Receive FIFO write clock. Data is read from the Receive FIFO, using the RXCLK input clock, when addressed by CE and selected by RXEN. These modes are usually used for products containing external decoders or descramblers, that must meet specific protocol requirements. New data may be read from the Receive FIFO any time that the FIFO status flags indicate a non-empty condition (RXEMPTY is deasserted). To ensure that data is not lost, the Receive FIFO must be read faster than data is loaded into the Receive FIFO. If the receiver is to provide framed characters, it is necessary for the transmit end to include JK or LM sync characters in the data stream. This can be done by: ■ operating the transmitter in encoded mode and writing JK or LM characters into the data stream ■ operating the transmitter in pre-encoded mode and writing the 10-bit value for an encoded JK (1100010001) or LM (011000100011) character to the data stream ■ not enabling the transmitter when it is operated in synchronous mode, or by allowing the transit FIFO to go empty when it is operated in asynchronous mode. BIST Operation and Reporting The CY7C9689ADX HOTLink Transceiver incorporates the same Built-In Self-Test (BIST) capability. This link diagnostic uses a Linear Feedback Shift Register (LFSR) to generate a 511-character repeating sequence that is compared, character-for-character, at the receiver. BIST mode is intended to check the entire high-speed serial link at full link-speed, without the use of specialized and expensive test equipment. The complete sequence of characters used in BIST are documented in Table 4. Page 40 of 56 CY7C9689A Figure 5. Built-In Self-Test Illustration TXCLK TXBISTEN TXEMPTY TXHALF TXFULL Enable TX BIST BIST LOOP REFCLK LOW to enable FIFO Flags LOW to enable VLTN reads Ignore these outputs ERROR Start of RX BIST Wait Forced to indicate EMPTY by BIST BIST LOOP Enable RX BIST BIST Enable Inputs There are separate BIST enable inputs for the transmit and receive paths of the CY7C9689A. These inputs are both active LOW; i.e., BIST is enabled in its respective section of the device when the BIST enable input is determined to be at a logic-0 level. Both BIST enable inputs are asynchronous; i.e., they are synchronized inside the CY7C9689A to the internal state machines. BIST Transmit Path OUTB TXCMD[1:0] TXSC/D TXDATA[9:0] TXEN Don’t Care Start of RX BIST match OUTA CE RXEN RXDATA[9:0] RXSC/D RXCMD[1:0] VLTN RXEMPTY RXHALF RXFULL RXBISTEN RXCLK CY7C9689A Start of TX BIST INA INB A/B HIGH to select A maximum limit while the BIST operation takes place. To allow removal of stale data from the Transmit FIFO, it may also be reset during a BIST operation. The reset operation proceeds as documented, with the exception of the information presented on the TXEMPTY FIFO status flag. Since this flag is used to present BIST loop status, it continues to reflect the state of the transmit BIST loop status until TXBISTEN is no longer recognized internally. The completion of the reset operation may still be monitored through the TXFULL FIFO status flag. The TXEMPTY flag, when used for transmit BIST progress indication, continues to reflect the active HIGH or active LOW settings determined by the UTOPIA or Cascade timing model selected by EXTFIFO; i.e., when configured for the Cascade timing model, the TXEMPTY and TXFULL FIFO flags are active HIGH, when configured for the UTOPIA timing model the TXEMPTY and TXFULL FIFO flags are active LOW. The illustration in Figure 5 uses the UTOPIA conventions. The transmit path operation with BIST is controlled by the TXBISTEN input and overrides most other inputs (see Figure 5). When the Transmit FIFO is enabled (not bypassed) and TXBISTEN is recognized internally, all reads from the Transmit FIFO are suspended and the BIST generator is enabled to sequence out the 511 character repeating BIST sequence. If the recognition occurs in the middle of a data field, the following data is not transmitted at that time, but remains in the Transmit FIFO. Once the TXBISTEN signal is removed, the data in the Transmit FIFO is again available for transmission. To ensure proper data handling at the destination, the transmit host controller should either use TXHALT to prevent transmission of data at specific boundaries, or allow the Transmit FIFO to completely empty before enabling BIST. When TXBISTEN is first recognized, the TXEMPTY flag is clocked to a reset state, regardless of the addressed state of the Transmit FIFO (if CE is LOW or not), but is not driven out of the part unless CE has been sampled asserted (LOW). Following this, on each completed pass through the BIST loop, the TXEMPTY flag is set for one interface clock period (TXCLK or REFCLK). With transmit BIST enabled, the Transmit FIFO remains available for loading of data. It may be written up to its normal The TXEMPTY flag remains set until the interface is addressed and the state of TXEMPTY has been observed. If the device is Document Number: 38-02020 Rev. *H Page 41 of 56 CY7C9689A not addressed (CE is not sampled LOW), the flag remains set internally regardless of the number of TXCLK clock cycles that are processed. If the device status is not polled on a sufficiently regular basis, it is possible for the host system to miss one or more of these BIST loop indications. A pass through the loop is defined as that condition where the Encoder generates the 0x00 (where 0x denotes Hex number, e.g. 0x00 denotes HEX00) state. Depending on the initial state of the BIST LFSR, the first pass through the loop may occur at substantially less than 511 character periods. Following the first pass, as long as TXBISTEN remains LOW, all remaining passes are exactly 511 characters in length. When the Transmit FIFO is bypassed, the interface is clocked by the REFCLK signal instead of TXCLK. While the active or asserted state of the TXEMPTY signal is still controlled by the EXTFIFO, the state of any completed BIST loops is no longer preserved. Instead, the TXEMPTY flag reflects the dynamic state of the BIST loop progress, and is asserted only once every 511 character periods. If the interface is not addressed at the time that this occurs, then the FIFO status flags remain in a high-Z state and the loop event is lost. BIST Receive Path The receive path operation in BIST is similar to that of the transmit path. While the Receive FIFO is enabled (not bypassed) and RXBISTEN is recognized internally, all writes to the Receive FIFO are suspended. Any data present in the Receive FIFO when RXBISTEN is recognized remains in the FIFO and cannot be read until the BIST operation is complete. The data in the Receive FIFO remains valid, but is NOT available for reading through the host parallel interface. This is because the error output indicator for receive BIST operations is the VLTN signal, which is normally part of the RXDATA bus. To prevent read operations while BIST is in operation, the RXEMPTY and RXHALF flags are forced to indicate an Empty condition. Once RXBISTEN has been removed and recognized internally, the Receive FIFO status flags are updated to reflect the current content status of the Receive FIFO. To allow removal of stale data from the Receive FIFO, it may be reset during a BIST operation. The reset operation proceeds as documented, with the exception that the RXEMPTY and RXHALF status flags already indicate an empty condition. The RXFULL flag is used to present BIST progress. The active (asserted) state on RXFULL (and RXEMPTY) remain controlled by the present operating mode and interface timing model (UTOPIA or Cascade). When RXBISTEN has been recognized, RXFULL becomes the receive BIST loop indicator (regardless of the logic state of FIFOBYP). When RXBISTEN is first recognized, the RXFULL flag is clocked to a set state, regardless of the addressed state of the Receive FIFO (if CE is sampled LOW or not). Following this, RXFULL remains set until the receiver detects the start of the BIST pattern. Then RXFULL is deasserted for the duration of the BIST pattern, pulsing asserted for one RXCLK period on the last symbol of each BIST loop. If 14 of 28 consecutive characters are received in error, RXFULL returns to the set state until the start of a BIST sequence is again detected. Document Number: 38-02020 Rev. *H Just like the BIST status flag on the transmit data path, the RXFULL flag captures the asserted states, and keeps them until they are read. This means that if the status flag is not read on a regular basis, events may be lost. The detection of errors is presented on the VLTN output. Unlike the RXFULL FIFO status flag, the active state of this output is not controlled by the EXTFIFO input. With the Receive FIFO enabled, these outputs should operate the same as the RXFULL flag, with respect to preserving the detection state of an error until it is read. Unlike the RXFULL flag, which only needs the CY7C9689A to be addressed (CE sampled LOW by RXCLK) to enable the RXFULL three-state driver, and an RXCLK to “read” the flag, the VLTN output requires a selection (assertion of RXEN while addressed) to enable the RXDATA bus three-state drivers. The selection process is necessary to ensure that a multi-PHY implementation does not enable multiple VLTN drivers at the same time. When the Receive FIFO is bypassed, the interface is clocked by the RXCLK output signal. While the active or asserted state of the RXFULL signal is still controlled by the EXTFIFO input, the state of any completed BIST loops or detected errors are no longer preserved. Instead, the RXFULL flag reflects the dynamic state of the BIST loop progress, and is asserted only once every 511 character periods. If the interface is not addressed at the time that this occurs, then the FIFO status flags remain in a high-Z state and the loop event is lost. This is also true of the VLTN output, such that if the CY7C9689A receive path is not selected to enable the RXDATA bus three-state drivers, the detection of a BIST miscompare is lost. BIST Three-state Control When BIST is enabled on either the transmitter or the receiver, the three-state enable signals for the BIST status flags and error indicators work the same as for normal data processing. The output drivers for the BIST status that is presented on FIFO status flags are only enabled when CE has been sampled asserted (LOW) by the respective clock (TXCLK, RXCLK, or REFCLK). To access the BIST error information, it is necessary to perform a read cycle of the addressed receiver. This means that CE must be LOW to enable the receiver (Rx_Match), and RXEN must be asserted from HIGH to LOW to select the device. Because the part is in BIST, no data is read from the FIFO, but the data bus is driven. This allows the VLTN indicator to be driven onto the RXDATA bus. So long as RXEN remains asserted, the receiver stays selected, the data bus remains driven, and VLTN has meaning. Bus Interfacing The parallel transmit and receive host interfaces to the CY7C9689A are configurable for either synchronous or asynchronous operation. Each of these configurations supports two selectable timing and control models of Shared Bus or Cascade. All asynchronous bus configurations have the internal Transmit and Receive FIFOs enabled. This allows data to be written or read from these FIFOs at any rate up to the maximum 50-MHz clock rate of the FIFOs. All internal operations of the CY7C9689A do not use the external TXCLK or RXCLK, but Page 42 of 56 CY7C9689A instead make use of synthesized derivatives of REFCLK for transmit path operations and a recovered character clock for receive path operations. All synchronous bus configurations require the bus interface operations to be synchronous to REFCLK on the transmit path and the recovered clock (output as RXCLK) on the receive path. The internal FIFOs are bypassed in all synchronous modes. The two supported timing and control models are Shared Bus and Cascade. The Shared Bus is based on the timing model of a FIFO with active LOW FIFO status flags and read/write enables. The Cascade timing model is a modification of the Shared Bus model that changes the flags and FIFO read/write enables to active HIGH. This model is present primarily to allow depth expansion of the internal FIFO by direct coupling to external CY7C42x5 synchronous FIFOs. To allow this direct coupling, the cycle-to-cycle timing between the transmit and receive enables (TXEN and RXEN) are also modified to ensure correct data transfer. These four configurations of bus operation and timing/control can all be used with or without external FIFOs. Depending on the specific mode selected, the amount of external hardware necessary to properly couple the CY7C9689A to state machines or external FIFOs is minimal in all cases, and may be zero if the proper configuration is selected. With only minor exceptions, all configurations of the CY7C9689A in the Shared Bus mode borrowed concepts from the ATM Forum’s UTOPIA Bus operation. concepts of addressing and selection to control the enabled/disabled state of the output drivers, and when data can be written to or read from the part. Shared Bus Interface Concept The CY7C9689A Parallel Interface is designed for interfacing to a Shared Bus. The maximum TXCLK and RXCLK frequency is 50 MHz, which provides a total bandwidth of 50Million characters per second in each direction. More than two CY7C9689A can be serviced on the same bus at full serial line speed. The CY7C9689A is designed to be the Slave in Master-Slave type of shared bus architecture. Generally, the bus Master (a Medium Access Device, MAC) is a higher layer device that sources out going data/command and sinks incoming data/command to/from Slaves (CY7C9689A) on the shared bus (see Figure 6) Figure 6. Shared Bus Architecture The data bus (TXDATA, RXDATA), command bus (TXCMD, RXCMD) and FIFO status flags (TXFULL, RXEMPTY, etc.) of each CY7C9689A on the shared bus can be connected together respectively. Each Slave can be assigned an address. The address of each Slave can be decoded by a decoder which drives the CE input of each Slave. The bus Master will poll each Slave by selecting (or “Addressing”) the device, and sample the FIFO flags. Depending on the FIFOs status on each Slave device, the Master can schedule read accesses to Slaves which have data in the RXFIFOs, and write accesses to Slaves which have room in the TXFIFOs. While data is being transferred on the data/command bus, the bus Master can continue to poll each Slave device independently. Device Selection All actions on the Shared Bus interface are controlled by the Chip Enable and selection states of the interface. These states control the read and write access to the Receive and Transmit FIFOs, access to the FIFO status flags, reset of the Transmit and Receive FIFOs, and read and write access to the Serial Address Register. The CY7C9689A supports the concept of an “address match” through a single Chip Enable (CE) input. Address Match and FIFO Flag Access The CY7C9689A makes use of a single active-LOW Chip Enable (CE) to generate address-match conditions. This allows multiple CY7C9689A devices to share a common bus, with device output three-state controls being managed by either an address match condition (CE sampled LOW), or by a selection state. The Transmit and Receive FIFO flag output drivers are enabled in any TXCLK, REFCLK, or RXCLK cycle following CE being sampled asserted (LOW) by the rising edge of the respective clock. The CE input is sampled separately by the clocks for the transmit and receive interfaces, which allows these clocks to be both asynchronous to each other, and to operate at different clock rates. An example of both Transmit and Receive FIFO flag access is shown in Figure 7 Figure 7. FIFO Flag Driver Enables. TXCLK CE TXFULL Bus Master Transmit Port Addressing CEn CE1 CE2 CY7C9689A Valid CY7C9689A RXCLK TXDATA/TXCMD RXDATA/RXCMD Status, Control ............ CE CY7C9689A RXEMPTY Valid Receive Port Addressing Document Number: 38-02020 Rev. *H Page 43 of 56 CY7C9689A When the Transmit FIFO is enabled (FIFOBYP is HIGH) and CE is sampled LOW by the rising edge of TXCLK, the output drivers for the TXFULL and TXEMPTY FIFO flags are enabled. When CE is sampled HIGH by the rising edge of TXCLK, these same output drivers are disabled. All normal forms of selection require that an Chip Enable must be asserted (CE sampled LOW) either at the same time as the selection control signal being sampled asserted, or one or more clock cycles prior to the selection control signal being sampled asserted. When the Transmit FIFO is bypassed (FIFOBYP is LOW and not in byte-packed mode) and CE is sampled LOW by the rising edge of REFCLK, the output drivers for the TXFULL and TXEMPTY FIFO flags are enabled. When CE is sampled HIGH by the rising edge of REFCLK, the FIFO flag output drivers are disabled. Transmit Data Selection When CE is sampled LOW by the rising edge of RXCLK (input or output), the output drivers for the RXFULL and RXEMPTY FIFO flags are enabled. When CE is sampled HIGH by the rising edge of RXCLK, the FIFO flag output drivers are disabled. Device Selection The concept of selection is used to control the access to the transmit and receive parallel-data ports of the device. There are three primary types of selection: ■ Transmit data selection (with and without internal Transmit FIFO) ■ Receive data selection (with and without internal Receive FIFO) ■ Continuous selection (for either or both transmit and receive interfaces). In addition to these normal selection types, there are two additional sequences that are used to control the internal Transmit and Receive FIFOs reset operations, and to control read/write access to the Serial Address Register: ■ Transmit reset sequence ■ Receive reset sequence. Of these operations, the transmit data selection and transmit reset sequence are mutually exclusive and cannot exist at the same time. The receive data selection and receive reset sequence are also mutually exclusive and cannot exist at the same time. Either transmit operation can exist at the same time as either receive operation. Document Number: 38-02020 Rev. *H Asynchronous With Shared Bus Timing and Control (Transmit FIFO Enabled) When CE is sampled LOW and TXRST is sampled HIGH by the rising edge of TXCLK, a Tx_Match condition is generated. This Tx_Match condition continues until CE is sampled HIGH or TXRST is sampled LOW at the rising edge of TXCLK. When a Tx_Match (or Tx_RstMatch) condition is present, the TXEMPTY and TXFULL output drivers are enabled. When a Tx_Match (or Tx_RstMatch) condition is not present, these same drivers are disabled (High-Z). The selection state of the Transmit FIFO is entered when a Tx_Match condition is present, and TXEN transitions from HIGH to LOW. Once selected, the Transmit FIFO remains selected until TXEN is sampled HIGH by the rising edge of TXCLK. In the selected state, data present on the TXDATA inputs is captured and stored in the Transmit FIFO. This transmit interface selection process is shown in Figure 8. Synchronous With Shared Bus Timing and Control (Transmit FIFO Bypassed) When the Transmit FIFO is bypassed (FIFOBYP is LOW and not in byte-packed mode), the CY7C9689A must still be selected to write data into the Transmit Input Register. When CE is sampled LOW and TXRST is sampled HIGH by the rising edge of REFCLK, a Tx_Match condition is generated. This Tx_Match condition continues until CE is sampled HIGH or TXRST is sampled LOW at the rising edge of REFCLK. When a Tx_Match (or Tx_RstMatch) condition is present, the TXEMPTY and TXFULL output drivers are enabled (with the Transmit FIFO bypassed, the status flags normally indicate an Empty condition). When a Tx_Match (or Tx_RstMatch) condition is not present, these same drivers are disabled (High-Z). Page 44 of 56 CY7C9689A Figure 8. Transmit Selection with Transmit FIFO Enabled TXCLK TXRST CE [48] Tx_Match Note 49 TXEN Tx_Selected [48] TXDATA/TXCMD D1 (Shared Bus Timing) TXDATA/TXCMD (Cascade Timing) TXFULL Not Full D2 D3 D1 D2 D3 Not Full Note 49 The selection state of the Transmit Input Register is entered when a Tx_Match condition is present, and TXEN transitions from HIGH to LOW. Once selected, the transmit input register remains selected until TXEN is sampled HIGH by the rising edge of REFCLK. In the selected state, data present on the TXDATA inputs is captured in the Transmit Input Register and passed to the Serializer or Encoder (as selected by the ENCBYP input). This transmit interface selection process is shown in Figure 9. When the 4B/5B Encoder is enabled and data is not written to the Transmit Input Register, the data stream is automatically padded with JK or LM SYNC characters. When the 4B/5B, 5B/6B Encoder is disabled and no data is written to the Transmit Input Register, JK or LM SYNC characters are also automatically padded with SYNC characters. Receive Data Selection Asynchronous With Shared Bus Timing and Control (Receive FIFO Enabled) When CE is sampled LOW and RXRST is sampled HIGH by the rising edge of RXCLK input, an Rx_Match condition is generated. This Rx_Match condition continues until CE is sampled HIGH or RXRST is sampled LOW at the rising edge of RXCLK input. When an Rx_Match (or Rx_RstMatch) condition is present, the RXEMPTY and RXFULL output drivers are enabled. When an Rx_Match (or Rx_RstMatch) condition is not present, these same drivers are disabled (High-Z). The selection state of the Receive FIFO is entered when an Rx_Match condition is present, and RXEN transitions from HIGH to LOW. Once selected, the Receive FIFO remains selected until RXEN is sampled HIGH by the rising edge of RXCLK input. The selected state initiates a read cycle from the Receive FIFO and enables the Receive FIFO data onto the RXDATA bus. This receive interface selection process is shown in Figure 10 Notes 48. Signal names listed in italics are internal signals, shown for reference only. 49. Signals shown as dotted lines indicate timing and levels when configured for external FIFOs (EXTFIFO is HIGH). Document Number: 38-02020 Rev. *H Page 45 of 56 CY7C9689A Figure 9. Transmit Selection with Transmit FIFO Bypassed REFCLK TXRST CE Tx_Match [48] Note 49 TXEN Tx_Selected [48] TXDATA/TXCMD D1 (Shared Bus Timing) TXDATA/TXCMD (Cascade Timing) TXFULL Not Full D2 D3 D1 D2 D3 Not Full Note 49 Synchronous With UTOPIA Timing and Control (Receive FIFO Bypassed) When the Receive FIFO is bypassed (FIFOBYP is LOW), the CY7C9689A must still be selected to enable the output drivers for the RXDATA bus. With the Receive FIFO bypassed, RXCLK becomes a synchronous output clock operating at the character rate. When CE is sampled LOW and RXRST is sampled HIGH by the rising edge of RXCLK output, an Rx_Match condition is generated. This Rx_Match condition continues until CE is sampled HIGH or RXRST is sampled LOW at the rising edge of RXCLK. When an Rx_Match (or Rx_RstMatch) condition is present, the RXEMPTY and RXFULL output drivers are enabled. With the Document Number: 38-02020 Rev. *H Receive FIFO bypassed, these flags normally indicate a non-empty condition but may indicate empty if a JK or LM SYNC character is present in the output register and the receiver discard policy is non-0. When an Rx_Match (or Rx_RstMatch) condition is not present, these same drivers are disabled (High-Z). The selection state of the Receive Output Register is entered when an Rx_Match condition is present, and RXEN transitions from HIGH to LOW. Once selected, the Receive Output Register remains selected until RXEN is sampled HIGH by the rising edge of RXCLK output. In the selected state, the output drivers for the RXDATA outputs are enabled, and new data is presented to the RXDATA bus on every clock cycle Page 46 of 56 CY7C9689A Figure 10. Receive Selection with Receive FIFO Enabled RXCLK RXRST CE [48] Rx_Match RXEN Rx_Selected Note 49 [48] RXDATA/RXCMD D1 Not Empty RXEMPTY D3 Not Empty Note 49 Continuous Selection Continuous Selection is a specialized form of selection which does not require sequenced assertion of CE and TXEN or RXEN to select the device for data transfers. In this Continuous Selection mode, the CE and associated TXEN or RXEN enable signal must be asserted when the device is powered up or during assertion of RESET. So long as these signals remain asserted, the device remains selected and data is accepted and presented on every clock cycle. Note: The use of continuous selection makes it impossible to reset the respective internal FIFOs, or to access the Serial Address Register. FIFO Reset Address Match When CE and TXRST are both LOW, and this condition is sampled by the rising edge of TXCLK, a Tx_RstMatch condition is generated. This Tx_RstMatch condition continues until CE or TXRST is sampled HIGH by the rising edge of TXCLK. When a Tx_RstMatch (or Tx_Match) condition is present, the TXEMPTY and TXFULL output drivers are enabled (just as in a normal Tx_Match condition). When a Tx_RstMatch (or Tx_Match) condition is not present, these same drivers are disabled (High-Z). The Transmit FIFO reset Address Match is shown in Figure 11. Note that although TXRST remains LOW for more than one clock cycle, the Tx_RstMatch does not because the CE signal is no longer asserted (LOW). When CE and RXRST are both LOW, and this condition is sampled by the rising edge of RXCLK, an Rx_RstMatch condition is generated. This Rx_RstMatch condition continues until CE or RXRST is sampled HIGH, at the rising edge of Document Number: 38-02020 Rev. *H D2 Figure 11. Transmit FIFO Reset Address Match TXCLK TXRST CE Tx_RstMatch Tx_Match [48] [48] TXFULL Valid RXCLK. When an Rx_RstMatch (or Rx_Match) condition is present, the RXEMPTY and RXFULL output drivers are enabled. When an Rx_RstMatch (or Rx_Match) condition is not present, these same drivers are disabled (High-Z). The Receive FIFO reset Address Match is shown in Figure 12. Note that while the FIFO flags remain asserted for more than one clock cycle, this is due to an Rx_Match condition, not a continuation of the Rx_RstMatch. Page 47 of 56 CY7C9689A Figure 12. Receive FIFO Reset Address Match RXCLK RXRST CE Rx_RstMatch Rx_Match [48] [48] RXEMPTY Valid Valid FIFO Reset Sequence On power-up, the Transmitter and Receiver FIFOs are cleared automatically. If the usage of the FIFOs in specific operating modes results in stale or unwanted data, this data can be cleared by resetting the respective FIFO. Data in the Transmit FIFO will empty automatically if it is enabled to read the FIFO (assuming TXHALT is not LOW). Stale received data can be “flushed” by reading it, or the Receive FIFO can be reset to remove the unwanted data. The Transmit and Receive FIFOs are reset when the Tx_RstMatch or Rx_RstMatch condition remains present for eight consecutive clock cycles. Any disruption of the reset sequence prior to reaching the eight cycle count, either by removal of CE or the respective TXRST or RXRST, or assertion of the associated TXEN or RXEN, terminates the sequence and does not reset the FIFO. Because CE must remain asserted during the reset sequence, the addressed FIFO flags remain driven during the entire sequence. Transmit FIFO Reset Sequence The Transmit FIFO reset sequence (see Figure 15) is started when TXRST and CE are first sampled LOW by the rising edge of TXCLK. Because a Tx_RstMatch condition is present, the Transmit FIFO flags are asserted and can be used to track the status of any Transmit FIFO reset in progress. Once the reset sequence has reached its maximum count (eight TXCLK cycles), the Transmit FIFO flags are asserted to indicate a FULL condition (TXEMPTY is deasserted, and both TXHALF and Document Number: 38-02020 Rev. *H TXFULL are asserted). This indicates that the Transmit FIFO reset has been recognized by the Transmit Control State Machine and that a reset has been started. However, if the TXEN is asserted prior to or during the assertion and sampling of TXRST, the reset sequence is inhibited until TXEN is removed. Note: The FIFO FULL state forced by the reset operation is different from a FULL state caused by normal FIFO data writes. For normal FIFO write operations, when FULL is first asserted, the Transmit FIFO must still accept up to four additional writes of data. When a FULL state is asserted due to a Transmit FIFO reset operation, the FIFO will not accept any additional data. The Transmit FIFO reset does not complete until the external reset condition is removed. This can be removed by deassertion of either TXRST or CE. If CE is deasserted (HIGH) to remove the reset condition, the Transmit FIFO flag’s drivers are disabled, and the Transmit FIFO must be addressed at a later time to validate completion of the Transmit FIFO reset. If TXRST is deasserted (HIGH) to remove the reset condition, the Tx_RstMatch is changed to a Tx_Match, and the Transmit FIFO status flags remain driven. The Transmit FIFO reset operation is complete when the Transmit FIFO flags indicate an EMPTY state (TXEMPTY is asserted and both TXHALF and TXFULL are deasserted). A valid Transmit FIFO reset sequence is shown in Figure 15. Here the TXRST and CE are asserted (LOW) at the same time. When these signals are both sampled LOW by TXCLK, a Tx_RstMatch condition is present. With TXEN deasserted (HIGH), the Transmit FIFO is not selected for data transfers. This Tx_RstMatch condition must remain for eight TXCLK cycles to initiate the Tx_FIFO_Reset. Following this the TXFULL FIFO status flag is asserted to indicate that the Transmit FIFO reset sequence has completed and that a Transmit FIFO reset is in progress. When the TXRST signal is deasserted (HIGH), CE remains LOW to allow the FIFO status flags to be driven. This allows the completion of the reset operation to be monitored. To allow better multi-tasking on multi-PHY implementations, it is possible to deassert CE (HIGH) as soon as the FULL state is indicated. The FIFO reset operation will complete and the EMPTY state (indicating completion of the reset operation) can be detected during a separate polling operation. For those links implemented with a single PHY, it is possible to hardwire CE LOW and still perform normal accesses and reset operations. In a single-PHY implementation, a Transmit FIFO reset can never be initiated with TXEN asserted at the same time as TXRST. Since CE is always LOW, any assertion of TXEN causes the Transmit FIFO to be selected, clearing the reset counter. Page 48 of 56 CY7C9689A Figure 13. Transmit FIFO Reset Sequence with Constant CE TXCLK TXRST TXEN Note 50 CE Tx_RstMatch [51] [51] Tx_Match Tx_FIFO_Reset [51] TXFULL Note 50 Not Full Full Notes 50. Signals shown as dotted lines indicate timing and levels when configured for external FIFOs (EXTFIFO is HIGH). 51. Signal names listed in italics are internal signals, shown for reference only. Document Number: 38-02020 Rev. *H Page 49 of 56 CY7C9689A Figure 14. Invalid Transmit FIFO Reset Sequence with TXEN Asserted TXCLK TXRST Note 50 TXEN CE [51] Tx_RstMatch Tx_Match Tx_FIFO_Reset [51] [51] TXFULL Note 50 Not Full Figure 15. Transmit FIFO Reset Sequence TXCLK TXRST TXEN Note 50 CE [51] Tx_RstMatch Tx_Match [51] [51] Tx_FIFO_Reset TXFULL Note 50 Not Full Figure 14 shows a sequence of input signals which will not produce a FIFO reset. In this case TXEN was asserted to select a Transmit FIFO for data transfers. Because TXEN remains active, the assertion of CE and TXRST does not initiate a reset Document Number: 38-02020 Rev. *H Full operation. This is shown by the TXFULL flag remaining HIGH (deasserted) following what would be the normal expiration of the seven-state reset counter. Page 50 of 56 CY7C9689A Receive FIFO Reset Sequence The Receive FIFO reset sequence operates (for the most part) the same as the Transmit FIFO reset sequence. The same requirements exist for the assertion state of RXRST and selection of the interface. A sample Receive FIFO reset sequence is shown in Figure 16. Upon recognition of a Receive FIFO reset, the Receive FIFO flags are forced to indicate an EMPTY state to prohibit additional reads from the FIFO. Unlike the Transmit FIFO, where the internal completion of the reset operation is shown by first going FULL and later going EMPTY when the internal reset is complete, there is no secondary indication of the completion of the internal reset of the Receive FIFO. The Receive FIFO is usable as soon as new data is placed into it by the Receive Control State Machine Figure 16. Receive FIFO Reset Sequence. RXCLK RXRST RXEN Note 50 CE [51] Rx_RstMatch Rx_Match Rx_FIFO_Reset [51] [51] RXEMPTY Document Number: 38-02020 Rev. *H Note 50 Not Empty Empty Page 51 of 56 CY7C9689A Printed Circuit Board Layout Suggestions Power Supply Bypass 0.01-F MLC X7R 1206 Chip Cap (4 sites) INA± OUTA± OUTB± INB± Power Supply Bypass 0.01-F MLC X7R CURSETB Resistor CURSETA Resistor Power Supply Bypass 0.01-F MLC X7R 1206 Chip Cap (2 sites) RXSC/D REFCLK CY7C9689A-AC CY7C9689A-AC Power Supply Bypass 0.01-F MLC X7R RESET Via to VDD plane Power Supply Bypass 0.01-F MLC X7R Via to VSS plane This is a typical printed circuit board layout showing example placement of power supply bypass components and other components mounted on the same side as the CY7C9689A. Other layouts, including cases with components mounted on the reverse side would work as well Document Number: 38-02020 Rev. *H Page 52 of 56 CY7C9689A Ordering Information Ordering Code Package Name Package Type Operating Range CY7C9689A-AXC A100 Pb-Free 100-lead Thin Quad Flat Pack Commercial CY7C9689A-AXI A100 Pb-Free 100-lead Thin Quad Flat Pack Industrial Ordering Code Definitions CY 7 C 9689 A - A X C Temperature Grade C : Commercial, I : Industrial Lead free Package (A : TQFP) Silicon Revision TAXI Compatible HOTLink Transceiver CMOS Technology Marketing Code Company ID Package Diagram Figure 17. 100-Pin TQFP (14 × 14 ×1.4 mm) 51-85048 *I Document Number: 38-02020 Rev. *H Page 53 of 56 CY7C9689A Acronyms Document Conventions Table 9. Acronyms Used in this Document Units of Measure Acronym Description Symbol Unit of Measure AC alternating current BIST built-in self-test CDR clock/data recovery CML current mode logic DC direct current DVB digital video broadcasting mA milliamperes ECL emitter coupled logic mm millimeters I/O input/output ms milliseconds JTAG joint test action group mV millivolts LFI link fault indicator nA nanoamperes LFSR linear feedback shift register ns nanoseconds LPEN local loopback input nV nanovolts PECL positive-ECL ohms PLL phase-locked loop pp peak-to-peak pF picofarads TTL transistor-transistor logic VCO voltage controlled oscillator Document Number: 38-02020 Rev. *H °C degrees Celsius Mbps megabits per second MHz megahertz µA microamperes µs microseconds ps picoseconds sps samples per second V volts Page 54 of 56 CY7C9689A Document History Page Document Title: CY7C9689A TAXI™-compatible HOTLink® Transceiver Document Number: 38-02020 Rev. ECN No. Issue Date Orig. of Change ** 106249 04/20/01 SZV Changed from Spec number: 38-00758 to 38-02020 *A 107695 06/28/01 SPN Changed part number: CY7C9689 to CY7C9689A *B 113563 04/10/02 REV Removed parity reference Deleted mention of Byte-packer Fixed formatting to change mF to F *C 118318 11/08/02 REV Changed pins 23 and 29 to RXDATA[11:10]/RXCMD[1:0] LFI was changed from “three state” to just output pin Fixed flip flop to Q as output and D as input Font problem with up-arrow symbols corrected *D 506290 See ECN PCX Added Pb-Free part numbers to ordering information *E 2896245 03/19/10 CGX Updated ordering information. Updated package diagram. *F 3383795 09/26/11 SAAC Added Contents. Added Ordering Code Definitions. Updated Package Diagram. Added Acronyms, and Units of Measure. Updated to new template. *G 4421000 06/26/2014 LISZ Description of Change Updated Pin Descriptions: Updated pin 12 description. Updated CY7C9689A HOTLink Transmitter Switching Waveforms: Updated Write Cycle, synchronous interface diagram on page 31 to add the timing specification. Updated to new template. *H 4571709 11/17/2014 YLIU No technical updates. Completing Sunset Review. Document Number: 38-02020 Rev. *H Page 55 of 56 CY7C9689A Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products Automotive Clocks & Buffers Interface Lighting & Power Control cypress.com/go/automotive cypress.com/go/clocks cypress.com/go/interface cypress.com/go/powerpsoc psoc.cypress.com/solutions PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP Cypress Developer Community Community | Forums | Blogs | Video | Training cypress.com/go/plc Memory cypress.com/go/memory PSoC cypress.com/go/psoc Touch Sensing cypress.com/go/support cypress.com/go/touch USB Controllers Wireless/RF Technical Support cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2001-2014. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-02020 Rev. *H Revised November 17, 2014 Page 56 of 56 HOTLink is a registered trademark of Cypress Semiconductor, Inc. AMD, TAXI, and TAXIchip are trademarks of Advanced Micro Devices. Inc. All product and company names mentioned in this document are trademarks of their respective holders.