Noise Suppression Products/EMI Suppression Filters > Leaded EMIFILr (Three-terminal Capacitor type) > Small Type Data Sheet 1 Leaded EMIFILr (Three-terminal Capacitor type) Small Type DSN6/DSS6 Series DSN6 Series c Dimensions c Insertion Loss Characteristics (Main Items) (50Ω - 50Ω) 2.54 max. 7.0 max. 0 1 2 Insertion Loss (dB) 8.0 max. I Q55 Type: 25.0 min. Q56 Type: 6.0±1.0 Q54 Type: 4.0±0.5 I 2.5±0.5 5.0±0.5 8 20 7 6 5 4 3 1: 22pF 2: 33pF 3: 47pF 4: 100pF 5: 270pF 6:1000pF 7: 2200pF 8: 10000pF 40 60 80 100 ø0.6 120 0.1 1 10 100 1000 GND Frequency (MHz) (in mm) c Rated Value (p: lead type/packaging code) Part Number Capacitance Rated Voltage Operating Temperature Range Rated Current DSN6NC51H220p 22pF ±20% 50Vdc 6A -25 to +85°C DSN6NC51H330p 33pF ±20% 50Vdc 6A -25 to +85°C DSN6NC51H470p 47pF ±20% 50Vdc 6A -25 to +85°C DSN6NC51H101p 100pF ±20% 50Vdc 6A -25 to +85°C DSN6NC51H271p 270pF ±20% 50Vdc 6A -25 to +85°C DSN6NC51H102p 1000pF ±20% 50Vdc 6A -25 to +85°C DSN6NC51H222p 2200pF ±20% 50Vdc 6A -25 to +85°C DSN6NZ81H103p 10000pF 80/-20% 50Vdc 6A -25 to +85°C DSS6 Series Straight Type c Dimensions c Insertion Loss Characteristics (Main Items) 2.54 max. 8.0 max. *2 (50Ω - 50Ω) 0 5.0±0.5 I Q55 Type: 25.0 min. Q56 Type: 6.0±1.0 Q54 Type: 4.0±0.5 1 20 Insertion Loss (dB) I 2.5±0.5 2 7.0 max. *1 11 10 9 8 5 4 3 40 7 60 6 1: 22pF 2: 33pF 3: 47pF 4: 100pF 5: 150pF 6: 220pF 7: 270pF 8: 470pF 9: 1000pF 10: 2200pF 11: 10000pF 80 100 ø0.6 GND (in mm) *1 There may be a hole on the top of ferrite beads, which causes no characteristics deterioration. *2 The bottom of the ferrite beads may not be level with each other. 120 0.1 1 10 100 1000 Frequency (MHz) Continued on the following page. oThis data sheet is applied for Lead EMIFILr Capacitor Type used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.5.9 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Leaded EMIFILr (Three-terminal Capacitor type) > Small Type Data Sheet 2 Continued from the preceding page. c Rated Value (p: lead type/packaging code) Capacitance Rated Voltage Rated Current Operating Temperature Range DSS6NC52A220p 22pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A330p 33pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A470p 47pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A101p 100pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A151p 150pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A221p 220pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A271p 270pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A471p 470pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A102p 1000pF ±20% 100Vdc 6A -25 to +85°C DSS6NE52A222p 2200pF 80/-20% 100Vdc 6A -25 to +85°C DSS6NZ82A103p 10000pF ±30% 100Vdc 6A -25 to +85°C Part Number DSS6 Series Incrimp Type c Dimensions c Insertion Loss Characteristics (Main Items) 2.54 max. 8.0 max. *2 10.0 max. 0 Insertion Loss (dB) I 2 20 *1 2.5±0.5 1 I T51 Type: 25.0 min. T41 Type: 4.0±0.5 11 10 9 8 5 4 3 1: 22pF 2: 33pF 3: 47pF 4: 100pF 5: 150pF 6: 220pF 7: 270pF 8: 470pF 9: 1000pF 10: 2200pF 11: 10000pF 40 7 6 60 80 5.0±0.5 100 ø0.6 120 GND (in mm) *1 There may be a hole on the top of ferrite beads, which causes no characteristics deterioration. *2 The bottom of the ferrite beads may not be level with each other. 0.1 1 10 100 1000 Frequency (MHz) c Rated Value (p: lead type/packaging code) Capacitance Rated Voltage Rated Current Operating Temperature Range DSS6NC52A220p 22pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A330p 33pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A470p 47pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A101p 100pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A151p 150pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A221p 220pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A271p 270pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A471p 470pF ±20% 100Vdc 6A -25 to +85°C DSS6NC52A102p 1000pF ±20% 100Vdc 6A -25 to +85°C DSS6NE52A222p 2200pF 80/-20% 100Vdc 6A -25 to +85°C DSS6NZ82A103p 10000pF ±30% 100Vdc 6A Part Number -25 to +85°C Continued on the following page. oThis data sheet is applied for Lead EMIFILr Capacitor Type used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.5.9 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Leaded EMIFILr (Three-terminal Capacitor type) > Small Type Data Sheet 3 Continued from the preceding page. c Equivalent Circuit c Equivalent Circuit DSN6 Series DSS6 Series GND GND No polarity. No polarity. c Packaging Minimum Quantity Minimum Order Quantity (order in sets only) (Pcs.) Part Number Ammo Pack ø320mm Paper reel 2000 — DS 6 Series Bulk (Bag) 250 Q55/T51 500 Q54/Q56/T41 Lead Type/Packaging Code Lead Type Lead Length* (in mm) Packaging Series Q55B 25.0 min. All series Q50B 4.0±0.5 DST9N/H Q52B Straight 6.0±1.0 Q54B 4.0±0.5 Q56B 6.0±1.0 T41B T51B Incrimp 4.0±0.5 20.0±1.0 Q92J 16.5±1.0 Q93J 18.5±1.0 Straight 16.5±1.0 Q93A 18.5±1.0 U21A U31A Incrimp Paper Reel (ø320mm) DSS9N/H 20.0±1.0 Q92A DSN6/9, DSS6/9 DSS6N 25.0 min. Q91J Q91A DST9N Bulk DSp6, DSN9N/H Ammo Pack 16.5±1.0 All series except DSS9N/H DSS6N 18.5±1.0 *Lead Distance between Reference and Bottom Planes except Bulk. Continued on the following page. oThis data sheet is applied for Lead EMIFILr Capacitor Type used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.5.9 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Leaded EMIFILr (Three-terminal Capacitor type) > Small Type Data Sheet 4 Continued from the preceding page. c Caution · Notice !Caution o Rating Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. o Soldering and Mounting 1. Mounting holes should be designed as specified in these specifications. Other designs than those shown in these specifications may cause cracks in ceramics that may lead to smoking or firing. 2. DSN9/DST9/DSN9H/DST9H/VFS9V Series Mounting for PCB. (Applis only to bulk type.) The form of the mounting hole of the bulk item is a triangle. The product should be inserted and soldered to each hole in the correct way as in Fig.2. (The center terminal and the other terminals become parallel when viewing the product from the side.) Smoking and firing maybe caused by incorrect mounting as in Fig.3. (The center terminal and the other terminals cross when viewing the product from the side.) Marking Side Center Terminal (Ground Terminal) Fig.2 Right Way Fig.3 Wrong Way Continued on the following page. oThis data sheet is applied for Lead EMIFILr Capacitor Type used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.5.9 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Leaded EMIFILr (Three-terminal Capacitor type) > Small Type Data Sheet 5 Continued from the preceding page. Notice o Storage and Operating Conditions <Operating Environment> 1. Do not use products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. 2. Do not use products near water, oil or organic solvents. Avoid environments where dust or dirt may adhere to the product. <Storage and Handling Requirements> 1. Storage Period Use the products within 12 months after delivery. Solderability should be checked if this period is exceeded. 2. Storage Conditions (1) Storage temperature: -10 to 40 degrees C Relative humidity: 15 to 85% Avoid sudden changes in temperature and humidity. (2) Do not store products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. (3) When restoring taping type (BL01RN1A1F1J), please attach the spacer between the flanges of the reel. The spacer is corrugated paper that is attached when shipping. <Using EMIGUARDr effectively> 1. Terminal (with mark) should be properly connected to the line of incoming electrostatic surge. (There is polarity.) Otherwise, no effect in ESD suppression can be expected (VFR3V). Example of input terminal Incoming Electrostatic Surges Example of output terminal Incoming Electrostatic Surges 2. Products should be used at rated voltage or less and rated current or less. 3. Products should not be applied for the absorption of surges that have large energy (e.g., induced lightning surges, switching surges) because it is designed for the absorption of electrostatic surges (VFR3V). 4. Electrostatic testing should be done on the following conditions (VFR3V). Ns;#2s62 ]2 < 8.0 x105 n: Times applied C: Charging Capacitance (pF) V: Testing Voltage (kV) R: Charging Resistance (Ω) o Soldering and Mounting 1. Washing Failure and degradation of a product are caused by the washing method. When you wash in conditions that are not in the mounting information, please contact Murata engineering. 2. Soldering Reliability decreases with improper soldering methods. Please solder by the standard soldering conditions shown in the mounting information. 3. Other Noise suppression levels resulting from Murata's EMI suppression filters EMIFILr may vary, depending on the circuits and ICs used, type of noise, mounting pattern, lead wire length, mounting location, and other operating conditions. Be sure to check and confirm in advance the noise suppression effect of each filter, in actual circuits, etc. before applying the filter in a commercial-purpose equipment design. oThis data sheet is applied for Lead EMIFILr Capacitor Type used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.5.9 http://www.murata.com/