Noise Suppression Products/EMI Suppression Filters > Chip EMIFILr LC Combined Type > Winding Type Data Sheet 1 Chip EMIFILr LC Combined Type NFW31SP Series (1206 Size) ■ Dimension ■ IL of Main Items 1.8±0.2 Insertion Loss (dB) (3) (2) NFW31SP157X1E4 NFW31SP207X1E4 20 1.6±0.2 3.2±0.3 (1) (50Ω - 50Ω) 0 2.3±0.2 (1) : Input electrode (2) : Ground electrode (3) : Output electrode NFW31SP307X1E4 NFW31SP407X1E4 NFW31SP507X1E4 40 NFW31SP106X1E4 NFW31SP206X1E4 NFW31SP506X1E4 60 NFW31SP107X1E4 ∗No polarity. 0.7±0.3 80 0.7±0.3 1 0.65±0.2 5 10 50 100 500 1000 2000 Frequency (MHz) (in mm) ■ Equivalent Circuit ■ Packaging (1) Input Code Packaging Minimum Quantity L 180mm Plastic Tape 2000 K 330mm Plastic Tape 7500 Output (3) GND (2) No polarity. ■ Rated Value (p: packaging code) Nominal Cut-off Freq. Insertion Loss (Cut-off Frequency) Attenuation at 500MHz Attenuation at 1000MHz Rated Current Rated Voltage Operating Temperature Range Number of Circuit NFW31SP106X1E4p 10MHz 6dB max. 30dBmin. 30dBmin. 200mA 25Vdc -40°C to 85°C 1 NFW31SP206X1E4p 20MHz 6dB max. 30dBmin. 30dBmin. 200mA 25Vdc -40°C to 85°C 1 NFW31SP506X1E4p 50MHz 6dB max. 30dBmin. 30dBmin. 200mA 25Vdc -40°C to 85°C 1 NFW31SP107X1E4p 100MHz 6dB max. 20dBmin. 30dBmin. 200mA 25Vdc -40°C to 85°C 1 NFW31SP157X1E4p 150MHz 6dB max. 30dBmin. 30dBmin. 200mA 25Vdc -40°C to 85°C 1 NFW31SP207X1E4p 200MHz 6dB max. 10dBmin. 30dBmin. 200mA 25Vdc -40°C to 85°C 1 NFW31SP307X1E4p 300MHz 6dB max. 5dBmin. 15dBmin. 200mA 25Vdc -40°C to 85°C 1 NFW31SP407X1E4p 400MHz 6dB max. - 10dBmin. 200mA 25Vdc -40°C to 85°C 1 NFW31SP507X1E4p 500MHz 6dB max. 6dBmax. 10dBmin. 200mA 25Vdc -40°C to 85°C 1 Part Number ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance . o This Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. data sheet is applied for LC Combined CHIP EMIFILr used for General Electronics equipment for your design. 2005.3.4 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Chip EMIFILr LC Combined Type > Winding Type Data Sheet 2 ! Note: 1. Export Control For customers outside Japan Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructive weapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons. For customers in Japan For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required for export. 2. Please contact our sales representatives or product engineers before using the products in this data sheet for the applications listed below, which require especially high reliability for the prevention of defects which might directly damage to a third party's life, body or property, or when one of our products is intended for use in applications other than those specified in this data sheet. w Aerospace equipment q Aircraft equipment r Power plant equipment e Undersea equipment y Transportation equipment (vehicles, trains, ships, etc.) t Medical equipment i Disaster prevention / crime prevention equipment u Traffic signal equipment !0 Application of similar complexity and/or reliability requirements to the applications listed in the above o Data-processing equipment 3. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product engineers. 4. This data sheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Especially, please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in them to prevent smoking and/or burning, etc. 5. You are able to read a detailed specification in the website of Search Engine (http://search.murata.co.jp/) or catalog library (http://www.murata.com/catalog/) before to require our product specification or to transact the approval sheet for product specification. 6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or contained in our data sheets. In this connection, no representation shall be made to the effect that any third parties are authorized to use the right mentioned above under licenses without our consent. 7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process. < < o This > > data sheet is applied for LC Combined CHIP EMIFILr used for General Electronics equipment for your design. 2005.3.4 http://www.murata.com/