PCB Connectors Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors Receptacles With Pin Contacts, Right Angle PCB Termination, 790-041P A Lightweight, rugged right angle headers feature gold-plated contacts for thru-hole printed circuit board termination. 790-041P connectors are free-standing (not for panel mounting) and mate to 790-025S cable plugs. Contacts are permanently installed and are sealed with epoxy. Shells are aluminum alloy. Threaded board mounting holes and integral standoffs simplify installation. EMI shroud improves EMI performance. Fluorosilicone face seal provides watertight interface. Available in 29 different contact arrangements, these connectors feature size #23 signal contacts along with #16 and #12 power contacts for up to 23 amps current rating. B C D E How To Order 790-041P J-25P2 Part Number Shell Size Insert Arr. 790-041P Header Receptacle with 90° PC Tail Pin Contacts for Termination to Backplanes or Flexible Circuits See Table 1 for Available Insert Arrangements Sample Part Number M P A Shell Finish Hardware Option PC Tail Length M a Electroless Nickel .125 Inch (3.2 mm.) MT .250 inch (6.4 mm.) general purpose applications Nickel-PTFE 1000 Hour Grey™ maximum corrosion protection and durability (non-reflective grey) B N No Hardware PC TAIL LENGTH ZNU Zinc-Nickel with Black Chromate F tactical applications (non-reflective black) Additional shell finishes are listed on page C-9. G H P Female Jackpost Specifications INDEX Current Rating Dielectric Withstanding Voltage Insulation Resistance Operating Temperature Shock Vibration © 2009 Glenair, Inc. Materials and Finishes #23 5 AMPS, #16 13 A., #12 23 A. #23 500 VAC RMS, #12 and #16 1800 VAC RMS 5000 megohms minimum -65° C. to +150° C. 300 g. 37 g. Shell Contacts Insulator EMI Shroud Interfacial Seal Jackposts Tray Encapsulant Aluminum alloy Copper alloy, 50 microinches gold plated Liquid crystal polymer (LCP) Aluminum alloy Flourosilicone rubber 300 series stainless steel Thermoplastic Epoxy Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-6 Rev. 04-July-2009 E-Mail: [email protected] PCB Connectors Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors Table 1 Contact Arrangements Layout A-5 Contact Quantity #23 #16 #12 2 B-9 9 C-13 13 D-15 15 D-3P3 Face View INTERFACIAL SEAL INSULATOR EMI SHROUD B SHELL 3 D-7P2 5 2 E-11P2 9 2 E-19 19 E-7P3 4 C Table 2 Hardware Option D 3 F-15P2 13 2 F-23 A PIN CONTACT EPOXY 5 B-2P2 Cross-Sectional View of 790-041P 23 F-5P5 N 5 G-33 33 H-10P4 6 No Mating Hardware 4 Connector is supplied with threaded holes. Shell sizes H and L have #6-32 threads, other sizes have #4-40 threads. Thread depth is .150" (3.8). P Jackposts Connector is supplied with non-removable stainless steel jackposts. Shell sizes H and L have #4-40 UNC thread, other sizes have #2-56 thread. E H-29P7 22 7 H-36P2 34 F 2 H-54P2 52 2 H-5P5 H-66 5 66 G J-17P4 13 4 J-25P2 23 2 J-33 33 J-7P7 H 7 K-27P4 23 4 K-43 K-9P9 INDEX K-35P2 33 2 43 9 L-6P6 © 2009 Glenair, Inc. 6 Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-7 Rev. 04-July-2009 E-Mail: [email protected] PCB Connectors Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors 790-041P Dimensions: Shell Sizes A-F, J, and K A 790-041P Shell Sizes A-F, J and K A MAX B .308 (7.82) MAX B BASIC .167 (4.95) C MAX Shell Size A B C D E F J K .228 (5.79) MIN .078 (1.98) MIN .500 (12.70) MAX C JACKPOST, #2-56 G 14.35 18.16 21.97 24.51 28.32 32.13 41.02 51.18 .401 .551 .701 .801 .951 1.101 1.460 1.860 10.19 14.00 17.81 20.35 24.16 27.96 37.08 47.24 A MAX 790-041P Dimensions: Shell Size G .228 (5.79) MIN 1.455 (36.96) MAX .209 (5.31) BASICBASIC 1.215 B (30.86) 1.079 (27.41) MAX .387 (9.83) MAX .078 (1.98) MIN .530 (13.46) MAX .195 (4.95) H .565 .715 .865 .965 1.115 1.265 1.615 2.015 B BASIC E F 20.45 24.26 28.07 30.61 34.42 38.23 47.12 57.28 C Max. In. mm. CONTACT TAIL DIA #23 CONTACT .018/.022 (0.46/0.56) #16 CONTACT .060/.064 (1.52/1.63) .540 (13.72) MAX .410 (10.41) 2-56 UNC-2B 2 PLACES .805 .955 1.105 1.205 1.355 1.505 1.855 2.255 B Basic In. mm. PC TAIL LENGTH ± .020 (0.51) CODE A: .125 (3.18) CODE B: .250 (6.35) .195 (4.95) D A Max. In. mm. JACKPOST, #2-56 .018/.022 (0.46/0.56) .615 (15.62) MAX .485 (12.62) INDEX 2-56 UNC-2B 2 PLACES PC TAIL LENGTH ± .020 (0.51) CODE A: .125 (3.18) CODE B: .250 (6.35) 1.215 (30.86) BASIC 1.455 (36.96) MAX © 2009 Glenair, Inc. Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-8 Rev. 04-July-2009 E-Mail: [email protected] PCB Connectors Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors 790-041P Dimensions: Shell Sizes H & L A #2-56 FLAT HEAD SCREW B A MAX B BASIC .415 (10.54) MAX C MAX .222 (5.64) C .288 (6.05) MIN .088 (2.24) .550 (13.97) MAX PC TAIL LENGTH ± .020 (0.51) CODE A: .125 (3.18) CODE B: .250 (6.35) JACKPOST, #4-40 CONTACT TAIL DIA #23 CONTACT .018/.022 (0.46/0.56) #16 CONTACT .060/.064 (1.52/1.63) #12 CONTACT .096/.092 (2.44/2.34) D E .195 (4.95) .491 (12.47) F .700 (17.78) MAX B BASIC 4-40 UNC-2B 2 PLCS G A MAX H 790-041P Shell Sizes H and L © 2009 Glenair, Inc. A Max. In. mm. B Basic In. mm. C Max. In. mm. 2.185 55.50 2.430 61.72 1.800 45.72 2.036 51.71 1.450 36.83 1.686 42.82 Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 INDEX Shell Size H L Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-9 Rev. 04-July-2009 E-Mail: [email protected] PCB Connectors Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors PCB Hole Patterns for 790-036P and 790-041P Receptacles A B C This section contains printed circuit board footprints for right angle Series 79 receptacles. The contact identification numbers are shown for the connector mounting side of the PC board. Contact tails are gold over nickel plated. Insert Arr. Contact Size #23 #16 #12 D .018-.022 .060-.064 .092-.096 0.46-0.56 1.52-1.63 2.34-2.44 CONNECTOR ORIENTATION 790-036P AND 790-041P PRINTED CIRCUIT BOARD PATTERNS Component Mounting Side of PCB Mating Face of Connector is Toward Top of Page .565 (14.35) .2825 (7.18) A-5 PC Tail Diameter Ø Diameter In. mm. .075 (1.91) TYP .094 ± .003 (2.39 ±0.08) 2x 5 .003 M A M .003 M A M 4 2 3 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 5x) 1 .075 (1.91) TYP .0375 (0.95) TYP .715 (18.16) E .270 (6.86) b-2p2 (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 2X) .003 M A M .094 ± .003 (2.39 ±0.08) 2x A1 A2 .003 M A M F .175 (4.45) .715 (18.16) .3575 (9.08) G b-9 .075 (1.91) TYP .094 ± .003 (2.39 ±0.08) 2x .003 M A M .003 M A M 9 5 8 7 3 4 6 1 2 .075 (1.91) TYP .0375 (0.95) TYP H .865 (21.97) .4325 (10.99) INDEX c-13 13 .094 ± .003 (2.39 ±0.08) 2x .003 M A M 7 12 6 .075 (1.91) TYP 5 4 3 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 13x) .003 M A M 8 10 9 11 .0375 (0.95) TYP © 2009 Glenair, Inc. (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 9x) 2 1 .075 (1.91) TYP Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-10 Rev. 04-July-2009 E-Mail: [email protected] PCB Connectors Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors Insert Arr. 790-036P AND 790-041P PRINTED CIRCUIT BOARD PATTERNS Component Mounting Side of PCB Mating Face of Connector is Toward Top of Page .965 (24.51) .4825 (12.26) D-15 .094 ± .003 (2.39 ±0.08) 2x 15 .003 M A M 8 14 13 7 12 10 3 4 5 6 .075 (1.91) TYP 11 A (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 15x) .003 M A M B 9 2 1 .075 (1.91) TYP .0375 (0.95) TYP C .965 (24.51) (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 3x) .4825 (12.26) .175 (4.45) 2x D-3P3 .094 ± .003 (2.39 ±0.08) 2x .003 M A M A3 .003 M A M D A1 A2 .965 (24.51) .205 (5.21) 2X .4825 (12.26) D-7P2 .094 ± .003 (2.39 ±0.08) 2x .075 (1.91) TYP 5 A2 A1 .003 M A M 2 3 1 .0375 (0.95) TYP .003 M A M 1.115 (28.32) 7 8 9 G 5 6 A2 A1 .003 M A M 3 4 2 1 .0375 (0.95) TYP 1.115 (28.32) .5575 (14.16) 10 9 8 .075 (1.91) TYP 16 15 18 17 7 6 4 .003 M A M 12 11 14 13 5 H (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 19x) INDEX .094 ± .003 (2.39 ±0.08) 2x 19 .0375 (0.95) TYP © 2009 Glenair, Inc. .075 (1.91) TYP .2795 (7.10) 2X .003 M A M .003 M A M F .003 M A M .075 (1.91) TYP (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 2X) E-19 .075 (1.91) TYP (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 9x) .5575 (14.16) .094 ± .003 (2.39 ±0.08) 2x E .003 M A M 4 (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 2X) E-11P2 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 5x) 3 2 1 .075 (1.91) TYP Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-11 Rev. 04-July-2009 E-Mail: [email protected] PCB Connectors A Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors Insert Arr. 790-036P AND 790-041P PRINTED CIRCUIT BOARD PATTERNS Component Mounting Side of PCB Mating Face of Connector is Toward Top of Page (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 3x) 1.115 (28.32) .5575 (14.16) B E-7P3 .094 ± .003 (2.39 ±0.08) 2x 3 4 A2 A3 .003 M A M A1 2 1 .2975 (7.56) 2x .0375 (0.95) 2x .075 (1.91) TYP 1.265 (32.13) C (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 13x) .6325 (16.07) f-15p2 D .094 ± .003 (2.39 ±0.08) 2x 13 11 10 12 .075 (1.91) TYP A2 A1 .003 M A M 6 (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 2x) 4 5 3 2 1 .075 (1.91) TYP .0375 (0.95) TYP .352 (8.94) 2X .003 M A M .003 M A M 7 8 9 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 23x) 1.265 (32.13) E .6325 (16.07) f-23 23 22 21 .094 ± .003 (2.39 ±0.08) 2x .003 M A M 12 11 10 F .003 M A M (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 4x) .175 (4.45) 2x 20 19 16 15 18 17 7 8 9 14 13 3 4 5 6 .003 M A M .075 (1.91) TYP 2 1 .075 (1.91) TYP .0375 (0.95) TYP 1.265 (32.13) .6325 (16.07) G f-5p5 .094 ± .003 (2.39 ±0.08) 2x A4 A5 .003 M A M (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 2x) 1.215 (30.86) .6075 (15.43) 33 32 INDEX g-33 .094 ± .003 (2.39 ±0.08) 2x .003 M A M 31 23 22 21 12 A1 .175 (4.45) 4x .003 M A M H A2 A3 11 10 .075 (1.91) TYP 30 20 9 29 28 19 8 27 26 16 15 18 17 7 6 5 4 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 33x) 25 24 14 13 3 2 1 .0375 (0.95) TYP © 2009 Glenair, Inc. .003 M A M Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 .075 (1.91) TYP Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-12 Rev. 04-July-2009 E-Mail: [email protected] PCB Connectors Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors Insert Arr. 790-036P AND 790-041P PRINTED CIRCUIT BOARD PATTERNS Component Mounting Side of PCB Mating Face of Connector is Toward Top of Page 1.800 (45.72) .900 (22.86) h-10p4 .0375 (0.95) TYP .125 ± .003 (3.18 ±0.08) 2x A4 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 6x) 6 .003 M A M 4 5 A3 A1 A2 3 .003 M A M A .075 (1.91) TYP 2 1 .075 (1.91) TYP .472 (11.99) .236 (5.99) TYP (HOLE TO ACCEPT .096 (2.44) MAX DIA CONTACT 4x) .003 M A M TYP 1.800 (45.72) .290 (7.37) h-29p7 .6125 .900 (22.86) .175 (4.45) TYP A5 A7 A6 .125 ± .003 (3.18 ±0.08) 2x 19 22 .003 M A M 21 16 18 20 17 15 14 A4 A3 A2 A1 .175 (4.45) TYP 13 10 7 4 1 12 9 11 8 6 5 2 .100 (2.54) TYP 1.800 (45.72) .900 (22.86) .125 ± .003 (3.18 ±0.08) 2x 33 32 16 15 17 .003 M A M 31 7 8 30 14 13 6 18 12 11 10 4 5 19 20 3 .0375 (0.95) .003 M A M 27 26 29 28 23 22 21 25 24 A2 .1725 (4.38) (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 34x) .075 (1.91) TYP 34 2 .075 (1.91) TYP A1 9 (HOLE TO ACCEPT .096 (2.44) MAX DIA CONTACT 2x) .003 M A M .944 (23.98) 1.800 (45.72) 52 .580 (14.73) h-54p2 .125 ± .003 (3.18 ±0.08) 2x 51 50 39 A2 27 .003 M A M 26 14 13 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 52x) 38 49 37 25 48 47 46 34 36 35 24 23 12 11 10 22 9 45 33 32 21 8 20 19 7 6 30 31 18 17 4 5 .075 (1.91) TYP 29 28 3 2 G A1 16 15 1 .0375 (0.95) TYP .075 (1.91) TYP .003 M A M (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 2x) .003 M A M 1.160 (29.46 H 1.800 (45.72) .900 (22.86) .125 ± .003 (3.18 ±0.08) 2x A5 A4 A3 A2 A1 .003 M A M .236 (5.99) 4x © 2009 Glenair, Inc. Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 (HOLE TO ACCEPT .096 (2.44) MAX DIA CONTACT 5x) .003 M A M Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-13 Rev. 04-July-2009 E-Mail: [email protected] INDEX H-5p5 F 41 40 43 42 44 E 1 .472 (11.99) .900 (22.86) C D .050 (1.27) TYP .075 (1.91) TYP .003 M A M .003 M A M h-36p2 3 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 22x) (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 7x) .075 (1.91) TYP B PCB Connectors A Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors Insert Arr. 790-036P AND 790-041P PRINTED CIRCUIT BOARD PATTERNS Component Mounting Side of PCB Mating Face of Connector is Toward Top of Page 1.800 (45.72) .900 (22.86) 66 65 64 B H-66 .125 ± .003 (3.18 ±0.08) 2x 49 48 .003 M A M 33 32 63 62 47 46 31 16 15 30 61 45 44 43 58 42 27 26 29 28 57 41 56 .0375 (0.95) TYP C 20 19 3 4 5 6 35 34 37 36 23 22 21 7 8 9 .075 (1.91) TYP 51 50 53 52 55 54 39 38 40 25 24 11 10 12 14 13 60 59 18 17 2 1 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 66x) .075 (1.91) TYP .003 M A M 1.615 (41.02) J-17P4 D .075 (1.91) TYP .094 ± .003 (2.39 ±0.08) 2x 13 A4 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 13x) .3725 (9.46) .8075 (20.51) .003 M A M 12 11 10 8 9 A3 A1 A2 .003 M A M 7 (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 4x) 3 4 5 6 2 .0375 (0.95) TYP 1 .075 (1.91) TYP .175 (4.45) TYP .003 M A M 1.615 (41.02) E .5475 (13.91) .8075 (20.51) .075 (1.91) TYP J-25P2 .094 ± .003 (2.39 ±0.08) 2x 23 22 21 19 16 15 18 17 14 13 A2 A1 .003 M A M 12 11 10 8 9 7 3 4 5 6 (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 23x) (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 2x) F 20 2 1 .075 (1.91) TYP .0375 (0.95) TYP .003 M A M .003 M A M (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 33x) 1.615 (41.02) .8075 (20.51) G .003 M A M .075 (1.91) TYP J-33 .094 ± .003 (2.39 ±0.08) 2x 33 .003 M A M 17 32 31 30 16 15 29 14 13 12 28 27 26 11 10 25 9 24 8 23 22 21 20 19 7 6 5 4 3 18 1 2 .075 (1.91) .0375 (0.95) TYP H 1.615 (41.02) .8075 (20.51) INDEX J-7P7 .094 ± .003 (2.39 ±0.08) 2x .003 M A M A7 A6 A5 (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 7x) A4 A3 A2 A1 .175 (4.45) 6x .003 M A M © 2009 Glenair, Inc. Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-14 Rev. 04-July-2009 E-Mail: [email protected] PCB Connectors Series 79 Micro-Crimp Section G: Right Angle Printed Circuit Board Connectors 790-036P AND 790-041P PRINTED CIRCUIT BOARD PATTERNS Component Mounting Side of PCB Mating Face of Connector is Toward Top of Page Insert Arr. A 2.015 (51.18) K-27P4 .0375 (0.95) TYP .075 (1.91) TYP .094 ± .003 (2.39 ±0.08) 2x 23 22 21 A4 .003 M A M 20 19 16 15 17 18 A2 11 10 9 8 7 6 5 2 3 4 .003 M A M .003 M A M 14 13 A3 12 (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 4x) (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 23x) A1 1 .075 (1.91) TYP .5755 (14.62) .1.0075 (25.59) 2.015 (51.18) .094 ± .003 (2.39 ±0.08) 2x K-35P2 33 32 31 30 .175 (4.45) TYP C (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 33x) .1.0075 (25.59) .003 M A M .075 (1.91) TYP 29 28 27 26 25 24 23 22 21 20 19 18 A2 A1 .003 M A M 16 15 17 14 13 12 (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 2x) 11 10 9 8 7 6 5 3 4 2 1 .075 (1.91) .0375 (0.95) TYP .003 M A M .750 (19.05) 2x 2.015 (51.18) (HOLE TO ACCEPT .022 (0.56) MAX DIA CONTACT 43x) .0375 (0.95) TYP .075 (1.91) TYP .220 (5.59) K-43 .094 ± .003 (2.39 ±0.08) 2x 43 .003 M A M 42 22 21 41 40 20 19 39 38 18 17 37 36 16 15 35 34 33 14 13 12 32 31 30 11 10 9 28 29 8 7 27 26 25 24 6 5 3 4 23 2 .075 (1.91) TYP 2.015 (51.18) A8 A9 .003 M A M A7 F .003 M A M A5 A6 A4 E (HOLE TO ACCEPT .064 (1.63) MAX DIA CONTACT 9x) .1.0075 (25.59) .094 ± .003 (2.39 ±0.08) 2x D 1 .1.0075 (25.59) K-9P9 B A3 G A1 A2 .175 (4.45) H 2.036 (51.71) .428 (10.87) L-6P6 A6 A5 A4 A3 A2 A1 .003 M A M (HOLE TO ACCEPT .096 (2.44) MAX DIA CONTACT 6x) .236 (5.99) 5x © 2009 Glenair, Inc. .003 M A M Dimensions in inches (millimeters) and are subject to change without notice. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com G-15 Rev. 04-July-2009 E-Mail: [email protected] INDEX .125 ± .003 (3.18 ±0.08) 2x