IDT IDT82V3255EDGBLANK

WAN PLL
IDT82V3255
Version 5
December 3, 2008
6024 Silver Creek Valley Road, San Jose, CA 95138
Telephone: (800) 345-7015 • TWX: 910-338-2070 • FAX: (408) 284-2775
Printed in U.S.A.
© 2008 Integrated Device Technology, Inc.
DISCLAIMER
Integrated Device Technology, Inc. reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. IDT does not assume any responsibility for use of any circuitry described other than the circuitry embodied in an IDT product. The Company makes no representations that circuitry
described herein is free from patent infringement or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent, patent rights or other
rights, of Integrated Device Technology, Inc.
LIFE SUPPORT POLICY
Integrated Device Technology's products are not authorized for use as critical components in life support devices or systems unless a specific written agreement pertaining to such intended use is executed between the manufacturer and an officer of IDT.
1. Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform, when properly used in
accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
2. A critical component is any components of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its
safety or effectiveness.
Table of Contents
FEATURES .............................................................................................................................................................................. 9
HIGHLIGHTS.................................................................................................................................................................................................... 9
MAIN FEATURES ............................................................................................................................................................................................ 9
OTHER FEATURES ......................................................................................................................................................................................... 9
APPLICATIONS....................................................................................................................................................................... 9
DESCRIPTION....................................................................................................................................................................... 10
FUNCTIONAL BLOCK DIAGRAM ........................................................................................................................................ 11
1 PIN ASSIGNMENT ........................................................................................................................................................... 12
2 PIN DESCRIPTION .......................................................................................................................................................... 13
3 FUNCTIONAL DESCRIPTION ......................................................................................................................................... 17
3.1
3.2
3.3
RESET ........................................................................................................................................................................................................... 17
MASTER CLOCK .......................................................................................................................................................................................... 17
INPUT CLOCKS & FRAME SYNC SIGNALS ............................................................................................................................................... 18
3.3.1 Input Clocks .................................................................................................................................................................................... 18
3.3.2 Frame SYNC Input Signals ............................................................................................................................................................ 18
3.4 INPUT CLOCK PRE-DIVIDER ...................................................................................................................................................................... 19
3.5 INPUT CLOCK QUALITY MONITORING ..................................................................................................................................................... 20
3.5.1 Activity Monitoring ......................................................................................................................................................................... 20
3.5.2 Frequency Monitoring ................................................................................................................................................................... 21
3.6 T0 / T4 DPLL INPUT CLOCK SELECTION .................................................................................................................................................. 22
3.6.1 External Fast Selection (T0 only) .................................................................................................................................................. 22
3.6.2 Forced Selection ............................................................................................................................................................................ 23
3.6.3 Automatic Selection ....................................................................................................................................................................... 23
3.7 SELECTED INPUT CLOCK MONITORING .................................................................................................................................................. 24
3.7.1 T0 / T4 DPLL Locking Detection ................................................................................................................................................... 24
3.7.1.1 Fast Loss .......................................................................................................................................................................... 24
3.7.1.2 Coarse Phase Loss .......................................................................................................................................................... 24
3.7.1.3 Fine Phase Loss ............................................................................................................................................................... 24
3.7.1.4 Hard Limit Exceeding ....................................................................................................................................................... 24
3.7.2 Locking Status ............................................................................................................................................................................... 24
3.7.3 Phase Lock Alarm (T0 only) .......................................................................................................................................................... 25
3.8 SELECTED INPUT CLOCK SWITCH ........................................................................................................................................................... 26
3.8.1 Input Clock Validity ........................................................................................................................................................................ 26
3.8.2 Selected Input Clock Switch ......................................................................................................................................................... 26
3.8.2.1 Revertive Switch ............................................................................................................................................................... 26
3.8.2.2 Non-Revertive Switch (T0 only) ........................................................................................................................................ 27
3.8.3 Selected / Qualified Input Clocks Indication ................................................................................................................................ 27
3.9 SELECTED INPUT CLOCK STATUS VS. DPLL OPERATING MODE ....................................................................................................... 28
3.9.1 T0 Selected Input Clock vs. DPLL Operating Mode .................................................................................................................... 28
3.9.2 T4 Selected Input Clock vs. DPLL Operating Mode .................................................................................................................... 30
3.10 T0 / T4 DPLL OPERATING MODE ............................................................................................................................................................... 31
3.10.1 T0 DPLL Operating Mode .............................................................................................................................................................. 31
3.10.1.1 Free-Run Mode ................................................................................................................................................................ 31
3.10.1.2 Pre-Locked Mode ............................................................................................................................................................. 31
3.10.1.3 Locked Mode .................................................................................................................................................................... 31
3.10.1.3.1 Temp-Holdover Mode .................................................................................................................................... 31
Table of Contents
3
December 3, 2008
IDT82V3255
3.11
3.12
3.13
3.14
3.15
3.16
3.17
WAN PLL
3.10.1.4 Lost-Phase Mode ............................................................................................................................................................. 31
3.10.1.5 Holdover Mode ................................................................................................................................................................. 31
3.10.1.5.1 Automatic Instantaneous ............................................................................................................................... 32
3.10.1.5.2 Automatic Slow Averaged ............................................................................................................................. 32
3.10.1.5.3 Automatic Fast Averaged .............................................................................................................................. 32
3.10.1.5.4 Manual ........................................................................................................................................................... 32
3.10.1.5.5 Holdover Frequency Offset Read .................................................................................................................. 32
3.10.1.6 Pre-Locked2 Mode ........................................................................................................................................................... 32
3.10.2 T4 DPLL Operating Mode .............................................................................................................................................................. 32
3.10.2.1 Free-Run Mode ................................................................................................................................................................ 32
3.10.2.2 Locked Mode .................................................................................................................................................................... 32
3.10.2.3 Holdover Mode ................................................................................................................................................................. 32
T0 / T4 DPLL OUTPUT ................................................................................................................................................................................. 34
3.11.1 PFD Output Limit ............................................................................................................................................................................ 34
3.11.2 Frequency Offset Limit .................................................................................................................................................................. 34
3.11.3 PBO (T0 only) ................................................................................................................................................................................. 34
3.11.4 Phase Offset Selection (T0 only) .................................................................................................................................................. 34
3.11.5 Four Paths of T0 / T4 DPLL Outputs ............................................................................................................................................. 34
3.11.5.1 T0 Path ............................................................................................................................................................................. 34
3.11.5.2 T4 Path ............................................................................................................................................................................. 35
T0 / T4 APLL ................................................................................................................................................................................................. 36
OUTPUT CLOCKS & FRAME SYNC SIGNALS ........................................................................................................................................... 36
3.13.1 Output Clocks ................................................................................................................................................................................. 36
3.13.2 Frame SYNC Output Signals ......................................................................................................................................................... 38
INTERRUPT SUMMARY ............................................................................................................................................................................... 40
T0 AND T4 SUMMARY ................................................................................................................................................................................. 40
POWER SUPPLY FILTERING TECHNIQUES ............................................................................................................................................. 41
LINE CARD APPLICATION .......................................................................................................................................................................... 42
4 MICROPROCESSOR INTERFACE .................................................................................................................................. 43
5 JTAG ................................................................................................................................................................................ 45
6 PROGRAMMING INFORMATION .................................................................................................................................... 46
6.1
6.2
REGISTER MAP ............................................................................................................................................................................................ 46
REGISTER DESCRIPTION ........................................................................................................................................................................... 51
6.2.1 Global Control Registers ............................................................................................................................................................... 51
6.2.2 Interrupt Registers ......................................................................................................................................................................... 58
6.2.3 Input Clock Frequency & Priority Configuration Registers ....................................................................................................... 62
6.2.4 Input Clock Quality Monitoring Configuration & Status Registers ........................................................................................... 73
6.2.5 T0 / T4 DPLL Input Clock Selection Registers ............................................................................................................................. 84
6.2.6 T0 / T4 DPLL State Machine Control Registers ........................................................................................................................... 88
6.2.7 T0 / T4 DPLL & APLL Configuration Registers ............................................................................................................................ 90
6.2.8 Output Configuration Registers .................................................................................................................................................. 103
6.2.9 PBO & Phase Offset Control Registers ...................................................................................................................................... 107
6.2.10 Synchronization Configuration Registers ................................................................................................................................. 109
7 THERMAL MANAGEMENT ........................................................................................................................................... 111
7.1
7.2
7.3
JUNCTION TEMPERATURE ...................................................................................................................................................................... 111
EXAMPLE OF JUNCTION TEMPERATURE CALCULATION ................................................................................................................... 111
HEATSINK EVALUATION .......................................................................................................................................................................... 111
8.1
8.2
8.3
ABSOLUTE MAXIMUM RATING ................................................................................................................................................................ 112
RECOMMENDED OPERATION CONDITIONS .......................................................................................................................................... 112
I/O SPECIFICATIONS ................................................................................................................................................................................. 113
8.3.1 CMOS Input / Output Port ............................................................................................................................................................ 113
8.3.2 PECL / LVDS Input / Output Port ................................................................................................................................................ 114
8 ELECTRICAL SPECIFICATIONS .................................................................................................................................. 112
Table of Contents
4
December 3, 2008
IDT82V3255
8.4
8.5
8.6
8.7
WAN PLL
8.3.2.1 PECL Input / Output Port ................................................................................................................................................ 114
8.3.2.2 LVDS Input / Output Port ................................................................................................................................................ 116
JITTER & WANDER PERFORMANCE ....................................................................................................................................................... 117
OUTPUT WANDER GENERATION ............................................................................................................................................................ 120
INPUT / OUTPUT CLOCK TIMING ............................................................................................................................................................. 121
OUTPUT CLOCK TIMING ........................................................................................................................................................................... 122
PACKAGE DIMENSIONS.................................................................................................................................................... 127
ORDERING INFORMATION................................................................................................................................................ 132
Table of Contents
5
December 3, 2008
List of Tables
Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Table 13:
Table 14:
Table 15:
Table 16:
Table 17:
Table 18:
Table 19:
Table 20:
Table 21:
Table 22:
Table 23:
Table 24:
Table 25:
Table 26:
Table 27:
Table 28:
Table 29:
Table 30:
Table 31:
Table 32:
Table 33:
Table 34:
Table 35:
Table 36:
Table 37:
Table 38:
Table 39:
Table 40:
Table 41:
Table 42:
Table 43:
Table 44:
Table 45:
Table 46:
Table 47:
Table 48:
Pin Description ............................................................................................................................................................................................. 13
Related Bit / Register in Chapter 3.2 ........................................................................................................................................................... 17
Related Bit / Register in Chapter 3.3 ........................................................................................................................................................... 18
Related Bit / Register in Chapter 3.4 ........................................................................................................................................................... 19
Related Bit / Register in Chapter 3.5 ........................................................................................................................................................... 21
Input Clock Selection for T0 Path ................................................................................................................................................................ 22
Input Clock Selection for T4 Path ................................................................................................................................................................ 22
External Fast Selection ................................................................................................................................................................................ 22
‘n’ Assigned to the Input Clock ..................................................................................................................................................................... 23
Related Bit / Register in Chapter 3.6 ........................................................................................................................................................... 23
Coarse Phase Limit Programming (the selected input clock of 2 kHz, 4 kHz or 8 kHz) .............................................................................. 24
Coarse Phase Limit Programming (the selected input clock of other than 2 kHz, 4 kHz and 8 kHz) .......................................................... 24
Related Bit / Register in Chapter 3.7 ........................................................................................................................................................... 25
Conditions of Qualified Input Clocks Available for T0 & T4 Selection ......................................................................................................... 26
Related Bit / Register in Chapter 3.8 ........................................................................................................................................................... 27
T0 DPLL Operating Mode Control ............................................................................................................................................................... 28
T4 DPLL Operating Mode Control ............................................................................................................................................................... 30
Related Bit / Register in Chapter 3.9 ........................................................................................................................................................... 30
Frequency Offset Control in Temp-Holdover Mode ..................................................................................................................................... 31
Frequency Offset Control in Holdover Mode ............................................................................................................................................... 32
Holdover Frequency Offset Read ................................................................................................................................................................ 32
Related Bit / Register in Chapter 3.10 ......................................................................................................................................................... 33
Related Bit / Register in Chapter 3.11 ......................................................................................................................................................... 35
Related Bit / Register in Chapter 3.12 ......................................................................................................................................................... 36
Outputs on OUT1 & OUT2 if Derived from T0/T4 DPLL Outputs ................................................................................................................ 36
Outputs on OUT1 & OUT2 if Derived from T0/T4 APLL .............................................................................................................................. 37
Frame Sync Input Signal Selection .............................................................................................................................................................. 38
Synchronization Control ............................................................................................................................................................................... 38
Related Bit / Register in Chapter 3.13 ......................................................................................................................................................... 39
Related Bit / Register in Chapter 3.14 ......................................................................................................................................................... 40
Read Timing Characteristics in Serial Mode ................................................................................................................................................ 44
Write Timing Characteristics in Serial Mode ................................................................................................................................................ 44
JTAG Timing Characteristics ....................................................................................................................................................................... 45
Register List and Map .................................................................................................................................................................................. 46
Power Consumption and Maximum Junction Temperature ....................................................................................................................... 111
Thermal Data ............................................................................................................................................................................................. 111
Absolute Maximum Rating ......................................................................................................................................................................... 112
Recommended Operation Conditions ........................................................................................................................................................ 112
CMOS Input Port Electrical Characteristics ............................................................................................................................................... 113
CMOS Input Port with Internal Pull-Up Resistor Electrical Characteristics ................................................................................................ 113
CMOS Input Port with Internal Pull-Down Resistor Electrical Characteristics ........................................................................................... 113
CMOS Output Port Electrical Characteristics ............................................................................................................................................ 113
PECL Input / Output Port Electrical Characteristics ................................................................................................................................... 115
LVDS Input / Output Port Electrical Characteristics ................................................................................................................................... 116
Output Clock Jitter Generation .................................................................................................................................................................. 117
Output Clock Phase Noise ......................................................................................................................................................................... 118
Input Jitter Tolerance (155.52 MHz) .......................................................................................................................................................... 118
Input Jitter Tolerance (1.544 MHz) ............................................................................................................................................................ 118
List of Tables
6
December 3, 2008
IDT82V3255
Table 49:
Table 50:
Table 51:
Table 52:
Table 53:
Table 54:
WAN PLL
Input Jitter Tolerance (2.048 MHz) ............................................................................................................................................................
Input Jitter Tolerance (8 kHz) ....................................................................................................................................................................
T0 DPLL Jitter Transfer & Damping Factor ...............................................................................................................................................
T4 DPLL Jitter Transfer & Damping Factor ...............................................................................................................................................
Input/Output Clock Timing ........................................................................................................................................................................
Output Clock Timing ..................................................................................................................................................................................
List of Tables
7
118
118
119
119
121
122
December 3, 2008
List of Figures
Figure 1. Functional Block Diagram ............................................................................................................................................................................ 11
Figure 2. Pin Assignment (Top View) .......................................................................................................................................................................... 12
Figure 3. Pre-Divider for An Input Clock ..................................................................................................................................................................... 19
Figure 4. Input Clock Activity Monitoring ..................................................................................................................................................................... 20
Figure 5. External Fast Selection ................................................................................................................................................................................ 22
Figure 6. T0 Selected Input Clock vs. DPLL Automatic Operating Mode ................................................................................................................... 29
Figure 7. T4 Selected Input Clock vs. DPLL Automatic Operating Mode ................................................................................................................... 30
Figure 8. On Target Frame Sync Input Signal Timing ................................................................................................................................................. 38
Figure 9. 0.5 UI Early Frame Sync Input Signal Timing .............................................................................................................................................. 38
Figure 10. 0.5 UI Late Frame Sync Input Signal Timing .............................................................................................................................................. 39
Figure 11. 1 UI Late Frame Sync Input Signal Timing ................................................................................................................................................. 39
Figure 12. IDT82V3255 Power Decoupling Scheme ................................................................................................................................................... 41
Figure 13. Line Card Application ................................................................................................................................................................................. 42
Figure 14. Serial Read Timing Diagram (CLKE Asserted Low) ................................................................................................................................... 43
Figure 15. Serial Read Timing Diagram (CLKE Asserted High) .................................................................................................................................. 43
Figure 16. Serial Write Timing Diagram ....................................................................................................................................................................... 44
Figure 17. JTAG Interface Timing Diagram ................................................................................................................................................................. 45
Figure 18. Recommended PECL Input Port Line Termination .................................................................................................................................. 114
Figure 19. Recommended PECL Output Port Line Termination ................................................................................................................................ 114
Figure 20. Recommended LVDS Input Port Line Termination .................................................................................................................................. 116
Figure 21. Recommended LVDS Output Port Line Termination ................................................................................................................................ 116
Figure 22. Output Wander Generation ...................................................................................................................................................................... 120
Figure 23. Input / Output Clock Timing ...................................................................................................................................................................... 121
Figure 24. 64-Pin PP Package Dimensions (a) (in Millimeters) ................................................................................................................................. 127
Figure 25. 64-Pin PP Package Dimensions (b) (in Millimeters) ................................................................................................................................. 128
Figure 26. 64-Pin EDG Package Dimensions (a) (in Millimeters) .............................................................................................................................. 129
Figure 27. 64-Pin EDG Package Dimensions (b) (in Millimeters) .............................................................................................................................. 130
Figure 28. EDG64 Recommended Land Pattern with Exposed Pad (in Millimeters) ................................................................................................. 131
List of Figures
8
December 3, 2008
WAN PLL
FEATURES
•
HIGHLIGHTS
•
•
The first single PLL chip:
• Features 0.1 Hz to 560 Hz bandwidth
• Exceeds GR-253-CORE (OC-12) and ITU-T G.813 (STM-16/
Option I) jitter generation requirements
• Provides node clocks for Cellular and WLL base-station (GSM
and 3G networks)
• Provides clocks for DSL access concentrators (DSLAM), especially for Japan TCM-ISDN network timing based ADSL equipments
•
•
•
•
•
•
•
•
MAIN FEATURES
•
•
•
•
•
•
•
•
•
•
•
Provides an integrated single-chip solution for Synchronous Equipment Timing Source, including Stratum 3, SMC, 4E and 4 clocks
Employs DPLL and APLL to feature excellent jitter performance
and minimize the number of the external components
Integrates T0 DPLL and T4 DPLL; T4 DPLL locks independently or
locks to T0 DPLL
Supports Forced or Automatic operating mode switch controlled by
an internal state machine; the primary operating modes are FreeRun, Locked and Holdover
Supports programmable DPLL bandwidth (0.1 Hz to 560 Hz in 11
steps) and damping factor (1.2 to 20 in 5 steps)
Supports 1.1X10-5 ppm absolute holdover accuracy and 4.4X10-8
ppm instantaneous holdover accuracy
Supports PBO to minimize phase transients on T0 DPLL output to
be no more than 0.61 ns
Supports phase absorption when phase-time changes on T0
selected input clock are greater than a programmable limit over an
interval of less than 0.1 seconds
Supports programmable input-to-output phase offset adjustment
Limits the phase and frequency offset of the outputs
Supports manual and automatic selected input clock switch
IDT82V3255
Supports automatic hitless selected input clock switch on clock failure
Supports three types of input clock sources: recovered clock from
STM-N or OC-n, PDH network synchronization timing and external
synchronization reference timing
Provides three 2 kHz, 4 kHz or 8 kHz frame sync input signals, and
a 2 kHz and an 8 kHz frame sync output signals
Provides 5 input clocks whose frequency cover from 2 kHz to
622.08 MHz
Provides 2 output clocks whose frequency cover from 1 Hz to
622.08 MHz
Provides output clocks for BITS, GPS, 3G, GSM, etc.
Supports PECL/LVDS and CMOS input/output technologies
Supports master clock calibration
Supports Line Card application
Meets Telcordia GR-1244-CORE, GR-253-CORE, ITU-T G.812,
ITU-T G.813 and ITU-T G.783 criteria
OTHER FEATURES
•
•
•
•
Serial microprocessor interface mode
IEEE 1149.1 JTAG Boundary Scan
Single 3.3 V operation with 5 V tolerant CMOS I/Os
64-pin TQFP package, Green package options available
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
BITS / SSU
SMC / SEC (SONET / SDH)
DWDM cross-connect and transmission equipments
Central Office Timing Source and Distribution
Core and access IP switches / routers
Gigabit and Terabit IP switches / routers
IP and ATM core switches and access equipments
Cellular and WLL base-station node clocks
Broadband and multi-service access equipments
Any other telecom equipments that need synchronous equipment
system timing
IDT and the IDT logo are trademarks of Integrated Device Technology, Inc.
9
 2008 Integrated Device Technology, Inc.
December 3, 2008
DSC-6773/5
IDT82V3255
WAN PLL
DESCRIPTION
the selected input clock. In Holdover mode, the DPLL resorts to the frequency data acquired in Locked mode. Whatever the operating mode is,
the DPLL gives a stable performance without being affected by operating conditions or silicon process variations.
The IDT82V3255 is an integrated, single-chip solution for the Synchronous Equipment Timing Source for Stratum 3, SMC, 4E and 4
clocks in SONET / SDH equipments, DWDM and Wireless base station,
such as GSM, 3G, DSL concentrator, Router and Access Network applications.
If the DPLL outputs are processed by T0/T4 APLL, the outputs of the
device will be in a better jitter/wander performance.
The device supports three types of input clock sources: recovered
clock from STM-N or OC-n, PDH network synchronization timing and
external synchronization reference timing.
The device provides programmable DPLL bandwidths: 0.1 Hz to 560
Hz in 11 steps and damping factors: 1.2 to 20 in 5 steps. Different settings cover all SONET / SDH clock synchronization requirements.
Based on ITU-T G.783 and Telcordia GR-253-CORE, the device consists of T0 and T4 paths. The T0 path is a high quality and highly configurable path to provide system clock for node timing synchronization
within a SONET / SDH network. The T4 path is simpler and less configurable for equipment synchronization. The T4 path locks independently
from the T0 path or locks to the T0 path.
A high stable input is required for the master clock in different applications. The master clock is used as a reference clock for all the internal
circuits in the device. It can be calibrated within ±741 ppm.
All the read/write registers are accessed through a serial microprocessor interface. The device supports Serial microprocessor interface
mode only.
An input clock is automatically or manually selected for T0 and T4
each for DPLL locking. Both the T0 and T4 paths support three primary
operating modes: Free-Run, Locked and Holdover. In Free-Run mode,
the DPLL refers to the master clock. In Locked mode, the DPLL locks to
Description
The device can be used typically in Line Card application.
10
December 3, 2008
Functional Block Diagram
IN3_CMOS
EX_SYNC3
EX_SYNC1
IN2_CMOS
IN2_DIFF
EX_SYNC2
IN1_CMOS
IN1_DIFF
Priority
Input Pre-Divider
EX_SYNC3
Input Pre-Divider
Priority
Priority
Input Pre-Divider
EX_SYNC2
Priority
Input Pre-Divider
EX_SYNC1
Priority
Input Pre-Divider
Input
T0 Input
Selector
Monitors
T4 Input
Selector
11
Divider
T0 PFD
& LPF
MUX
T4 DPLL
OSCI
APLL
PBO
Phase Offset
T0 8 kHz
Divider
T4 PFD
& LPF
Microprocessor Interface
T0 DPLL
12E1/24T1/E3/T3
16E1/16T1
GSM/OBSAI/16E1/16T1
77.76 MHz
8 k Divider
T0 77.76 MHz
12E1/24T1/E3/T3
16E1/16T1
GSM/GPS/16E1/16T1
77.76 MHz
JTAG
T0
APLL
MUX
T4
APLL
MUX
T0
APLL
T4
APLL
Output
10
10
OUT7
MUX
OUT3
MUX
Auto
Divider
Auto
Divider
Divider
Divider
MFRSYNC_2K
FRSYNC_8K
OUT2
OUT1
IDT82V3255
WAN PLL
FUNCTIONAL BLOCK DIAGRAM
Figure 1. Functional Block Diagram
December 3, 2008
IDT82V3255
PIN ASSIGNMENT
61
60
59
58
57
56
55
54
53
52
51
50
49
1
2
48
47
3
4
46
45
44
43
42
41
5
6
7
IDT82V3255
8
9
10
11
40
39
38
12
13
14
15
37
36
16
33
RST
SCLK
VDDD5
VDDD5
CS
SDI
CLKE
TMS
DGND5
VDDD5
VDDD5
TRST
VDDD5
EX_SYNC3
IN3_CMOS
EX_SYNC2
FRSYNC_8K
MFRSYNC_2K
OUT1_POS
OUT1_NEG
GND_DIFF
VDD_DIFF
IN1_POS
IN1_NEG
IN2_POS
IN2_NEG
NC
EX_SYNC1
IN1_CMOS
IN2_CMOS
DGND4
VDDD4
21
22
23
24
25
26
27
28
29
30
31
32
35
34
17
18
19
20
AGND
IC1
AGND1
VDDA1
INT_REQ
OSCI
DGND1
VDDD1
VDDD3
DGND3
DGND2
VDDD2
FF_SRCSW
VDDA2
AGND2
IC2
63
62
64
SONET/SDH
IC8
IC7
IC6
IC5
IC4
AGND3
VDDA3
OUT2
IC3
VDDD6
DGND6
SDO
TDI
TDO
TCK
1
WAN PLL
Figure 2. Pin Assignment (Top View)
Pin Assignment
12
December 3, 2008
IDT82V3255
2
WAN PLL
PIN DESCRIPTION
Table 1: Pin Description
Name
Pin No.
I/O
Description 1
Type
Global Control Signal
OSCI
6
I
CMOS
FF_SRCSW
13
I
pull-down
CMOS
OSCI: Crystal Oscillator Master Clock
A nominal 12.8000 MHz clock provided by a crystal oscillator is input on this pin. It is the
master clock for the device.
FF_SRCSW: External Fast Selection Enable
During reset, this pin determines the default value of the EXT_SW bit (b4, 0BH) 2. The
EXT_SW bit determines whether the External Fast Selection is enabled.
High: The default value of the EXT_SW bit (b4, 0BH) is ‘1’ (External Fast selection is
enabled);
Low: The default value of the EXT_SW bit (b4, 0BH) is ‘0’ (External Fast selection is disabled).
After reset, this pin selects an input clock pair for the T0 DPLL if the External Fast selection is
enabled:
High: Pair IN1_CMOS / IN1_DIFF is selected.
Low: Pair IN2_CMOS / IN2_DIFF is selected.
After reset, the input on this pin takes no effect if the External Fast selection is disabled.
SONET/SDH
64
I
pull-down
CMOS
SONET/SDH: SONET / SDH Frequency Selection
During reset, this pin determines the default value of the IN_SONET_SDH bit (b2, 09H):
High: The default value of the IN_SONET_SDH bit is ‘1’ (SONET);
Low: The default value of the IN_SONET_SDH bit is ‘0’ (SDH).
After reset, the value on this pin takes no effect.
RST
48
I
pull-up
CMOS
RST: Reset
A low pulse of at least 50 µs on this pin resets the device. After this pin is high, the device will
still be held in reset state for 500 ms (typical).
Frame Synchronization Input Signal
EX_SYNC1
28
EX_SYNC2
33
EX_SYNC3
35
I
pull-down
I
pull-down
I
pull-down
CMOS
EX_SYNC1: External Sync Input 1
A 2 kHz, 4 kHz or 8 kHz signal is input on this pin.
CMOS
EX_SYNC2: External Sync Input 2
A 2 kHz, 4 kHz or 8 kHz signal is input on this pin.
CMOS
EX_SYNC3: External Sync Input 3
A 2 kHz, 4 kHz or 8 kHz signal is input on this pin.
Input Clock
IN1_CMOS
29
IN2_CMOS
30
IN1_POS
23
IN1_NEG
24
IN2_POS
25
IN2_NEG
26
Pin Description
IN1_CMOS: Input Clock 1
A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz,
25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin.
IN2_CMOS: Input Clock 2
I
CMOS
A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz,
pull-down
25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin.
IN1_POS / IN1_NEG: Positive / Negative Input Clock 1
A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz,
I
PECL/LVDS 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 311.04 MHz or 622.08 MHz
clock is differentially input on this pair of pins. Whether the clock signal is PECL or LVDS is
automatically detected.
IN2_POS / IN2_NEG: Positive / Negative Input Clock 2
A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz,
I
PECL/LVDS 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 311.04 MHz or 622.08 MHz
clock is differentially input on this pair of pins. Whether the clock signal is PECL or LVDS is
automatically detected.
I
pull-down
CMOS
13
December 3, 2008
IDT82V3255
WAN PLL
Table 1: Pin Description (Continued)
Name
Pin No.
I/O
Type
Description 1
IN3_CMOS
34
I
pull-down
CMOS
IN3_CMOS: Input Clock 3
A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz,
25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin.
Output Frame Synchronization Signal
FRSYNC_8K
17
O
CMOS
MFRSYNC_2K
18
O
CMOS
FRSYNC_8K: 8 kHz Frame Sync Output
An 8 kHz signal is output on this pin.
MFRSYNC_2K: 2 kHz Multiframe Sync Output
A 2 kHz signal is output on this pin.
Output Clock
OUT1_POS
19
OUT1_NEG
20
OUT2
56
O
O
OUT1_POS / OUT1_NEG: Positive / Negative Output Clock 1
A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7,
PECL/LVDS 5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz,
77.76 MHz, 155.52 MHz, 311.04 MHz or 622.08 MHz clock is differentially output on this pair
of pins.
OUT2: Output Clock 2
A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7,
CMOS
5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz,
77.76 MHz or 155.52 MHz clock is output on this pin.
Microprocessor Interface
CS
44
I
pull-up
CMOS
INT_REQ
5
O
CMOS
SDI
43
CMOS
CLKE
42
I
pull-down
SDO
52
I/O
pull-down
CMOS
SCLK
47
I
pull-down
CMOS
CS: Chip Selection
A transition from high to low must occur on this pin for each read or write operation and this
pin should remain low until the operation is over.
INT_REQ: Interrupt Request
This pin is used as an interrupt request. The output characteristics are determined by the
HZ_EN bit (b1, 0CH) and the INT_POL bit (b0, 0CH).
SDI: Serial Data Input
In Serial mode, this pin is used as the serial data input. Address and data on this pin are serially clocked into the device on the rising edge of SCLK.
CLKE: SCLK Active Edge Selection
In Serial mode, this pin selects the active edge of SCLK to update the SDO:
High - The falling edge;
Low - The rising edge.
SDO: Serial Data Output
In Serial mode, this pin is used as the serial data output. Data on this pin is serially clocked
out of the device on the active edge of SCLK.
SCLK: Shift Clock
In Serial mode, a shift clock is input on this pin.
Data on SDI is sampled by the device on the rising edge of SCLK. Data on SDO is updated
on the active edge of SCLK. The active edge is determined by the CLKE.
JTAG (per IEEE 1149.1)
TRST
37
I
pull-down
CMOS
TMS
41
I
pull-up
CMOS
Pin Description
TRST: JTAG Test Reset (Active Low)
A low signal on this pin resets the JTAG test port.
This pin should be connected to ground when JTAG is not used.
TMS: JTAG Test Mode Select
The signal on this pin controls the JTAG test performance and is sampled on the rising edge
of TCK.
14
December 3, 2008
IDT82V3255
WAN PLL
Table 1: Pin Description (Continued)
Name
Pin No.
I/O
TCK
49
I
pull-down
CMOS
TDI
51
I
pull-up
CMOS
TDO
50
O
Description 1
Type
CMOS
TCK: JTAG Test Clock
The clock for the JTAG test is input on this pin. TDI and TMS are sampled on the rising edge
of TCK and TDO is updated on the falling edge of TCK.
If TCK is idle at a low level, all stored-state devices contained in the test logic will indefinitely
retain their state.
TDI: JTAG Test Data Input
The test data is input on this pin. It is clocked into the device on the rising edge of TCK.
TDO: JTAG Test Data Output
The test data is output on this pin. It is clocked out of the device on the falling edge of TCK.
TDO pin outputs a high impedance signal except during the process of data scanning.
This pin can indicate the interrupt of T0 selected input clock fail, as determined by the
LOS_FLAG_ON_TDO bit (b6, 0BH). Refer to Chapter 3.8.1 Input Clock Validity for details.
Power & Ground
VDDD1
8
VDDD2
12
VDDD3
9
VDDD4
32
VDDD5
36, 38, 39, 45, 46
VDDD6
VDDA1
54
4
VDDA2
14
Power
-
VDDA3
VDD_DIFF
DGND1
57
22
7
Power
-
DGND2
11
DGND3
10
Ground
-
DGND4
31
DGND5
40
DGND6
AGND1
53
3
AGND2
15
Ground
-
AGND3
GND_DIFF
AGND
58
21
1
Ground
Ground
-
VDDDn: 3.3 V Digital Power Supply
Each VDDDn should be paralleled with ground through a 0.1 µF capacitor.
Power
Pin Description
-
VDDAn: 3.3 V Analog Power Supply
Each VDDAn should be paralleled with ground through a 0.1 µF capacitor.
VDD_DIFF: 3.3 V Power Supply for OUT1
DGNDn: Digital Ground
AGNDn: Analog Ground
GND_DIFF: Ground for OUT1
AGND: Analog Ground
15
December 3, 2008
IDT82V3255
WAN PLL
Table 1: Pin Description (Continued)
Name
Pin No.
I/O
Description 1
Type
Others
IC1
2
IC2
16
IC3
55
IC4
59
IC5
60
IC6
61
IC7
62
IC8
NC
63
27
IC: Internal Connected
Internal Use. These pins should be left open for normal operation.
-
-
-
-
NC: Not Connected
Note:
1. All the unused input pins should be connected to ground; the output of all the unused output pins are don’t-care.
2. The contents in the brackets indicate the position of the register bit/bits.
3. N x 8 kHz: 1 < N < 19440.
4. N x E1: N = 1, 2, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64.
5. N x T1: N = 1, 2, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64, 96.
6. N x 13.0 MHz: N = 1, 2, 4.
7. N x 3.84 MHz: N = 1, 2, 4, 8, 16, 10, 20, 40.
Pin Description
16
December 3, 2008
IDT82V3255
WAN PLL
3
FUNCTIONAL DESCRIPTION
3.2
3.1
RESET
A nominal 12.8000 MHz clock, provided by a crystal oscillator, is
input on the OSCI pin. This clock is provided for the device as a master
clock. The master clock is used as a reference clock for all the internal
circuits. A better active edge of the master clock is selected by the
OSC_EDGE bit to improve jitter and wander performance.
The reset operation resets all registers and state machines to their
default value or status.
After power on, the device must be reset for normal operation.
MASTER CLOCK
In fact, an offset from the nominal frequency may input on the OSCI
pin. This offset can be compensated by setting the
NOMINAL_FREQ_VALUE[23:0] bits. The calibration range is within
±741 ppm.
For a complete reset, the RST pin must be asserted low for at least
50 µs. After the RST pin is pulled high, the device will still be in reset
state for 500 ms (typical). If the RST pin is held low continuously, the
device remains in reset state.
The performance of the master clock should meet GR-1244-CORE,
GR-253-CORE, ITU-T G.812 and G.813 criteria.
Table 2: Related Bit / Register in Chapter 3.2
Bit
Register
Address (Hex)
NOMINAL_FREQ_VALUE[23:0]
OSC_EDGE
NOMINAL_FREQ[23:16]_CNFG, NOMINAL_FREQ[15:8]_CNFG, NOMINAL_FREQ[7:0]_CNFG
DIFFERENTIAL_IN_OUT_OSCI_CNFG
06, 05, 04
0A
Functional Description
17
December 3, 2008
IDT82V3255
3.3
WAN PLL
INPUT CLOCKS & FRAME SYNC SIGNALS
For SDH and SONET networks, the default frequency is different.
SONET / SDH frequency selection is controlled by the IN_SONET_SDH
bit. During reset, the default value of the IN_SONET_SDH bit is determined by the SONET/SDH pin: high for SONET and low for SDH. After
reset, the input signal on the SONET/SDH pin takes no effect.
Altogether 5 clocks and 3 frame sync signals are input to the device.
3.3.1
INPUT CLOCKS
The device provides 5 input clock ports.
3.3.2
According to the input port technology, the input ports support the following technologies:
• PECL/LVDS
• CMOS
Three 2 kHz, 4 kHz or 8 kHz frame sync signals are input on the
EX_SYNC1 to EX_SYNC3 pins respectively. They are CMOS inputs.
The input frequency should match the setting in the SYNC_FREQ[1:0]
bits.
According to the input clock source, the following clock sources are
supported:
• T1: Recovered clock from STM-N or OC-n
• T2: PDH network synchronization timing
• T3: External synchronization reference timing
Only one of the three frame sync input signals is used for frame sync
output signal synchronization. Refer to Chapter 3.13.2 Frame SYNC
Output Signals for details.
Table 3: Related Bit / Register in Chapter 3.3
IN1_CMOS ~ IN3_CMOS support CMOS input signal only and the
clock sources can be from T1, T2 or T3.
IN1_DIFF and IN2_DIFF support PECL/LVDS input signal only and
automatically detect whether the signal is PECL or LVDS. The clock
sources can be from T1, T2 or T3.
Functional Description
FRAME SYNC INPUT SIGNALS
18
Bit
Register
Address (Hex)
IN_SONET_SDH
SYNC_FREQ[1:0]
INPUT_MODE_CNFG
09
December 3, 2008
IDT82V3255
3.4
WAN PLL
INPUT CLOCK PRE-DIVIDER
Once the division factor is set for the input clock selected by the
PRE_DIV_CH_VALUE[3:0] bits, it is valid until a different division factor
is set for the same input clock. The division factor is calculated as follows:
Each input clock is assigned an internal Pre-Divider. The Pre-Divider
is used to divide the clock frequency down to the DPLL required frequency, which is no more than 38.88 MHz. For each input clock, the
DPLL required frequency is set by the corresponding IN_FREQ[3:0] bits.
Division Factor = (the frequency of the clock input to the DivN
Divider ÷ the frequency of the DPLL required clock set by the
IN_FREQ[3:0] bits) - 1
If the input clock is of 2 kHz, 4 kHz or 8 kHz, the Pre-Divider is
bypassed automatically and the corresponding IN_FREQ[3:0] bits
should be set to match the input frequency; the input clock can be
inverted, as determined by the IN_2K_4K_8K_INV bit.
The DivN Divider can only divide the input clock whose frequency is
lower than (<) 155.52 MHz.
When the Lock 8k Divider is used, the input clock is divided down to
8 kHz automatically.
Each Pre-Divider consists of a HF (High Frequency) Divider (only
available for IN1_DIFF and IN2_DIFF), a DivN Divider and a Lock 8k
Divider, as shown in Figure 3.
The Pre-Divider configuration and the division factor setting depend
on the input clock on one of the clock input pin and the DPLL required
clock. Here is an example:
The HF Divider, which is only available for IN1_DIFF and IN2_DIFF,
should be used when the input clock is higher than (>) 155.52 MHz. The
input clock can be divided by 4, 5 or can bypass the HF Divider, as
determined by the IN1_DIFF_DIV[1:0]/IN2_DIFF_DIV[1:0] bits correspondingly.
The input clock on the IN2_DIFF pin is 622.08 MHz; the DPLL
required clock is 6.48 MHz by programming the IN_FREQ[3:0] bits of
register IN2_DIFF to ‘0010’. Do the following step by step to divide the
input clock:
1. Use the HF Divider to divide the clock down to 155.52 MHz:
622.08 ÷ 155.52 = 4, so set the IN2_DIFF_DIV[1:0] bits to ‘01’;
2. Use the DivN Divider to divide the clock down to 6.48 MHz:
Set the PRE_DIV_CH_VALUE[3:0] bits to ‘0110’;
Set the DIRECT_DIV bit in Register IN2_DIFF_CNFG to ‘1’ and
the LOCK_8K bit in Register IN2_DIFF_CNFG to ‘0’;
155.52 ÷ 6.48 = 24; 24 - 1 = 23, so set the
PRE_DIVN_VALUE[14:0] bits to ‘10111’.
Either the DivN Divider or the Lock 8k Divider can be used or both
can be bypassed, as determined by the DIRECT_DIV bit and the
LOCK_8K bit.
When the DivN Divider is used, the division factor setting should
observe the following order:
1. Select an input clock by the PRE_DIV_CH_VALUE[3:0] bits;
2. Write the lower eight bits of the division factor to the
PRE_DIVN_VALUE[7:0] bits;
3. Write the higher eight bits of the division factor to the
PRE_DIVN_VALUE[14:8] bits.
Pre-Divider
IN1_DIFF_DIV[1:0] bits / IN2_DIFF_DIV[1:0] bits
input clock
HF Divider
(for IN1_DIFF &
IN2_DIFF only)
DIRECT_DIV bit
DivN Divider
LOCK_8K bit
Lock 8k Divider
DPLL required clock
Figure 3. Pre-Divider for An Input Clock
Table 4: Related Bit / Register in Chapter 3.4
Bit
IN1_DIFF_DIV[1:0]
IN2_DIFF_DIV[1:0]
IN_FREQ[3:0]
DIRECT_DIV
LOCK_8K
IN_2K_4K_8K_INV
PRE_DIV_CH_VALUE[3:0]
PRE_DIVN_VALUE[14:0]
Functional Description
Register
Address (Hex)
IN1_DIFF_IN2_DIFF_HF_DIV_CNFG
18
IN1_CMOS_CNFG, IN2_CMOS_CNFG, IN1_DIFF_CNFG, IN2_DIFF_CNFG,
IN3_CNFG
16, 17, 19, 1A, 1D
FR_MFR_SYNC_CNFG
PRE_DIV_CH_CNFG
PRE_DIVN[14:8]_CNFG, PRE_DIVN[7:0]_CNFG
74
23
25, 24
19
December 3, 2008
IDT82V3255
3.5
WAN PLL
INPUT CLOCK QUALITY MONITORING
responding BUCKET_SEL[1:0] bits. Each leaky bucket configuration
consists of four elements: upper threshold, lower threshold, bucket size
and decay rate.
The qualities of all the input clocks are always monitored in the following aspects:
• Activity
• Frequency
The bucket size is the capability of the accumulator. If the number of
the accumulated events reach the bucket size, the accumulator will stop
increasing even if further events are detected. The upper threshold is a
point above which a no-activity alarm is raised. The lower threshold is a
point below which the no-activity alarm is cleared. The decay rate is a
certain period during which the accumulator decreases by 1 if no event
is detected.
The qualified clocks are available for T0/T4 DPLL selection. The T0
and T4 selected input clocks have to be monitored further. Refer to
Chapter 3.7 Selected Input Clock Monitoring for details.
3.5.1
ACTIVITY MONITORING
The leaky bucket configuration is programmed by one of four groups
of register bits: the BUCKET_SIZE_n_DATA[7:0] bits, the UPPER_
THRESHOLD_n_DATA[7:0] bits, the LOWER_THRESHOLD_n_
DATA[7:0] bits and the DECAY_RATE_n_DATA[1:0] bits respectively; ‘n’
is 0 ~ 3.
Activity is monitored by using an internal leaky bucket accumulator,
as shown in Figure 4.
Each input clock is assigned an internal leaky bucket accumulator.
The input clock is monitored for each period of 128 ms and the internal
leaky bucket accumulator increases by 1 when an event is detected; it
decreases by 1 if no event is detected within the period set by the decay
rate. The event is that an input clock drifts outside (>) ±500 ppm with
respect to the master clock within a 128 ms period.
The no-activity alarm status of the input clock is indicated by the
INn_CMOS_NO_ACTIVITY_ALARM bit (n = 1, 2, or 3) /
INn_DIFF_NO_ACTIVITY_ALARM bit (n = 1 or 2).
The input clock with a no-activity alarm is disqualified for clock selection for T0/T4 DPLL.
There are four configurations (0 - 3) for a leaky bucket accumulator.
The leaky bucket configuration for an input clock is selected by the cor-
clock signal with events
clock signal with no event
Input Clock
Decay
Rate
Bucket Size
Upper Threshold
Leaky Bucket Accumulator
Lower Threshold
0
No-activity Alarm Indication
Figure 4. Input Clock Activity Monitoring
Functional Description
20
December 3, 2008
IDT82V3255
3.5.2
WAN PLL
The input clock with a frequency hard alarm is disqualified for clock
selection for T0/T4 DPLL.
FREQUENCY MONITORING
Frequency is monitored by comparing the input clock with a reference clock. The reference clock can be derived from the master clock or
the output of T0 DPLL, as determined by the FREQ_MON_CLK bit.
In addition, if the input clock is 2 kHz, 4 kHz or 8 kHz, its clock edges
with respect to the reference clock are monitored. If any edge drifts outside ±5%, the input clock is disqualified for clock selection for T0/T4
DPLL. The input clock is qualified if any edge drifts inside ±5%. This
function is supported only when the IN_NOISE_WINDOW bit is ‘1’.
A frequency hard alarm threshold is set for frequency monitoring. If
the FREQ_MON_HARD_EN bit is ‘1’, a frequency hard alarm is raised
when the frequency of the input clock with respect to the reference clock
is above the threshold; the alarm is cleared when the frequency is below
the threshold.
The frequency of each input clock with respect to the reference clock
can be read by doing the following step by step:
1. Select an input clock by setting the IN_FREQ_READ_CH[3:0]
bits;
2. Read the value in the IN_FREQ_VALUE[7:0] bits and calculate
as follows:
The frequency hard alarm threshold can be calculated as follows:
Frequency Hard Alarm Threshold (ppm) = (ALL_FREQ_HARD_
THRESHOLD[3:0] + 1) X FREQ_MON_FACTOR[3:0]
If the FREQ_MON_HARD_EN bit is ‘1’, the frequency hard alarm
status
of
the
input
clock
is
indicated
by
the
INn_CMOS_FREQ_HARD_ALARM bit (n = 1, 2 or 3) /
INn_DIFF_FREQ_HARD_ALARM bit (n = 1 or 2). When the
FREQ_MON_HARD_EN bit is ‘0’, no frequency hard alarm is raised
even if the input clock is above the frequency hard alarm threshold.
Input Clock Frequency (ppm) = IN_FREQ_VALUE[7:0] X
FREQ_MON_FACTOR[3:0]
Note that the value set by the FREQ_MON_FACTOR[3:0] bits
depends on the application.
Table 5: Related Bit / Register in Chapter 3.5
Bit
Register
Address (Hex)
BUCKET_SIZE_n_DATA[7:0] (3 ≥ n ≥ 0)
UPPER_THRESHOLD_n_DATA[7:0] (3 ≥ n ≥ 0)
LOWER_THRESHOLD_n_DATA[7:0] (3 ≥ n ≥ 0)
DECAY_RATE_n_DATA[1:0] (3 ≥ n ≥ 0)
BUCKET_SIZE_0_CNFG ~ BUCKET_SIZE_3_CNFG
UPPER_THRESHOLD_0_CNFG ~ UPPER_THRESHOLD_3_CNFG
LOWER_THRESHOLD_0_CNFG ~ LOWER_THRESHOLD_3_CNFG
DECAY_RATE_0_CNFG ~ DECAY_RATE_3_CNFG
IN1_CMOS_CNFG, IN2_CMOS_CNFG, IN1_DIFF_CNFG,
IN2_DIFF_CNFG, IN3_CMOS_CNFG
33, 37, 3B, 3F
31, 35, 39, 3D
32, 36, 3A, 3E
34, 38, 3C, 40
BUCKET_SEL[1:0]
INn_CMOS_NO_ACTIVITY_ALARM (n = 1, 2, or 3)
INn_CMOS_FREQ_HARD_ALARM (n = 1, 2 or 3)
INn_DIFF_NO_ACTIVITY_ALARM (n = 1 or 2)
INn_DIFF_FREQ_HARD_ALARM (n = 1 or 2)
FREQ_MON_CLK
FREQ_MON_HARD_EN
ALL_FREQ_HARD_THRESHOLD[3:0]
FREQ_MON_FACTOR[3:0]
IN_NOISE_WINDOW
IN_FREQ_READ_CH[3:0]
IN_FREQ_VALUE[7:0]
Functional Description
16, 17, 19, 1A, 1D
IN1_IN2_CMOS_STS, IN3_CMOS_STS
44, 47
IN1_IN2_DIFF_STS
45
MON_SW_PBO_CNFG
0B
ALL_FREQ_MON_THRESHOLD_CNFG
FREQ_MON_FACTOR_CNFG
PHASE_MON_PBO_CNFG
IN_FREQ_READ_CH_CNFG
IN_FREQ_READ_STS
2F
2E
78
41
42
21
December 3, 2008
IDT82V3255
3.6
WAN PLL
T0 / T4 DPLL INPUT CLOCK SELECTION
Automatic selection is done based on the results of input clocks quality monitoring and the related registers configuration.
An input clock is selected for T0 DPLL and for T4 DPLL respectively.
The selected input clock is attempted to be locked in T0/T4 DPLL.
For T0 path, the EXT_SW bit and the T0_INPUT_SEL[3:0] bits determine the input clock selection, as shown in Table 6:
3.6.1
The External Fast selection is supported by T0 path only. In External
Fast selection, only IN1_CMOS/IN1_DIFF and IN2_CMOS/IN2_DIFF
pairs are available for selection. Refer to Figure 5. The results of input
clocks quality monitoring (refer to Chapter 3.5 Input Clock Quality Monitoring) do not affect input clock selection.
Table 6: Input Clock Selection for T0 Path
Control Bits
EXT_SW
T0_INPUT_SEL[3:0]
1
don’t-care
other than 0000
0000
0
EXTERNAL FAST SELECTION (T0 ONLY)
Input Clock Selection
External Fast selection
Forced selection
Automatic selection
The T0 input clock selection is determined by the FF_SRCSW pin
after reset (this pin determines the default value of the EXT_SW bit during reset, refer to Chapter 2 Pin Description), the
IN1_CMOS_SEL_PRIORITY[3:0]
bits
and
the
IN2_CMOS_SEL_PRIORITY[3:0] bits, as shown in Figure 5 and
Table 8:
For T4 path, the T4 DPLL may lock to a T0 DPLL output or lock independently from T0 path, as determined by the T4_LOCK_T0 bit. When
the T4 DPLL locks to the T0 DPLL output, the T4 selected input clock is
a 77.76 MHz or 8 kHz signal from the T0 DPLL 77.76 MHz path (refer to
Chapter 3.11.5.1 T0 Path), as determined by the T0_FOR_T4 bit. When
the T4 path locks independently from the T0 path, the T4 DPLL input
clock selection is determined by the T4_INPUT_SEL[3:0] bits. Refer to
Table 7:
IN1_CMOS_SEL_PRIORITY[3:0] bits
IN1_CMOS
FF_SRCSW pin
IN1_DIFF
Table 7: Input Clock Selection for T4 Path
Control Bits - T4_INPUT_SEL[3:0]
Input Clock Selection
other than 0000
0000
Forced selection
Automatic selection
attempted to be
locked in T0 DPLL
IN2_CMOS
IN2_DIFF
External Fast selection is done between IN1_CMOS/IN1_DIFF and
IN2_CMOS/IN2_DIFF pairs.
IN2_CMOS_SEL_PRIORITY[3:0] bits
Forced selection is done by setting the related registers.
Figure 5. External Fast Selection
Table 8: External Fast Selection
Control Pin & Bits
FF_SRCSW (after reset)
IN1_CMOS_SEL_PRIORITY[3:0]
IN2_CMOS_SEL_PRIORITY[3:0]
high
0000
other than 0000
don’t-care
low
don’t-care
0000
other than 0000
Functional Description
22
the Selected Input Clock
IN1_DIFF
IN1_CMOS
IN2_DIFF
IN2_CMOS
December 3, 2008
IDT82V3255
3.6.2
WAN PLL
INn_DIFF_SEL_PRIORITY[3:0] bits (n = 1 or 2). If more than one qualified input clock is available and has the same priority, the input clock
with the smallest ‘n’ is selected. See Table 9 for the ‘n’ assigned to the
input clock.
FORCED SELECTION
In Forced selection, the selected input clock is set by the
T0_INPUT_SEL[3:0] / T4_INPUT_SEL[3:0] bits. The results of input
clocks quality monitoring (refer to Chapter 3.5 Input Clock Quality Monitoring) do not affect the input clock selection.
3.6.3
Table 9: ‘n’ Assigned to the Input Clock
AUTOMATIC SELECTION
In Automatic selection, the input clock selection is determined by its
validity and priority. The validity depends on the results of input clock
quality monitoring (refer to Chapter 3.5 Input Clock Quality Monitoring).
In all the qualified input clocks, the one with the highest priority is
selected. The priority is configured by the corresponding
INn_CMOS_SEL_PRIORITY[3:0] bits (n = 1, 2 or 3) / the
Input Clock
‘n’ Assigned to the Input Clock
IN1_CMOS
IN1_DIFF
IN2_CMOS
IN2_DIFF
IN3_CMOS
1
2
3
4
5
Table 10: Related Bit / Register in Chapter 3.6
Bit
Register
Address (Hex)
EXT_SW
T0_INPUT_SEL[3:0]
T4_LOCK_T0
T0_FOR_T4
T4_INPUT_SEL[3:0]
MON_SW_PBO_CNFG
T0_INPUT_SEL_CNFG
0B
50
T4_INPUT_SEL_CNFG
51
IN1_IN2_CMOS_SEL_PRIORITY_CNFG,
IN3_CMOS_SEL_PRIORITY_CNFG
IN1_IN2_DIFF_SEL_PRIORITY_CNFG
T4_T0_REG_SEL_CNFG
INn_CMOS_SEL_PRIORITY[3:0] (n = 1, 2 or 3)
INn_DIFF_SEL_PRIORITY[3:0] (n = 1 or 2)
T4_T0_SEL
27 *, 2A *
28 *
07
Note: * The setting in the 27, 28 and 2A registers is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit.
Functional Description
23
December 3, 2008
IDT82V3255
3.7
WAN PLL
SELECTED INPUT CLOCK MONITORING
3.7.1.3
The T0/T4 DPLL compares the selected input clock with the feedback signal. If the phase-compared result exceeds the fine phase limit
programmed by the PH_LOS_FINE_LIMT[2:0] bits, a fine phase loss is
triggered. It is cleared once the phase-compared result is within the fine
phase limit.
The quality of the selected input clock is always monitored (refer to
Chapter 3.5 Input Clock Quality Monitoring) and the DPLL locking status
is always monitored.
3.7.1
T0 / T4 DPLL LOCKING DETECTION
The following events is always monitored:
• Fast Loss;
• Coarse Phase Loss;
• Fine Phase Loss;
• Hard Limit Exceeding.
3.7.1.1
The occurrence of the fine phase loss will result in T0/T4 DPLL
unlocked if the FINE_PH_LOS_LIMT_EN bit is ‘1’.
3.7.1.4
A fast loss is triggered when the selected input clock misses 2 consecutive clock cycles. It is cleared once an active clock edge is detected.
For T0 path, the occurrence of the fast loss will result in T0 DPLL
unlocked if the FAST_LOS_SW bit is ‘1’. For T4 path, the occurrence of
the fast loss will result in T4 DPLL unlocked regardless of the
FAST_LOS_SW bit.
Coarse Phase Loss
The DPLL soft limit is set by the DPLL_FREQ_SOFT_LIMT[6:0] bits
and can be calculated as follows:
The T0/T4 DPLL compares the selected input clock with the feedback signal. If the phase-compared result exceeds the coarse phase
limit, a coarse phase loss is triggered. It is cleared once the phase-compared result is within the coarse phase limit.
DPLL Soft Limit (ppm) = DPLL_FREQ_SOFT_LIMT[6:0] X 0.724
The DPLL hard limit is set by the DPLL_FREQ_HARD_LIMT[15:0]
bits and can be calculated as follows:
When the selected input clock is of 2 kHz, 4 kHz or 8 kHz, the coarse
phase limit depends on the MULTI_PH_8K_4K_2K_EN bit, the
WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0] bits. Refer to
Table 11. When the selected input clock is of other frequencies but 2
kHz, 4 kHz and 8 kHz, the coarse phase limit depends on the WIDE_EN
bit and the PH_LOS_COARSE_LIMT[3:0] bits. Refer to Table 12.
DPLL Hard Limit (ppm) = DPLL_FREQ_HARD_LIMT[15:0] X 0.0014
3.7.2
0
Coarse Phase Limit
don’t-care
±1 UI
0
±1 UI
1
set by the PH_LOS_COARSE_LIMT[3:0] bits
1
If the FAST_LOS_SW bit, the COARSE_PH_LOS_LIMT_EN bit, the
FINE_PH_LOS_LIMT_EN bit or the FREQ_LIMT_PH_LOS bit is ‘0’, the
DPLL locking status will not be affected even if the corresponding event
is triggered. If all these bits are ‘0’, the DPLL will be in locked state in 2
seconds.
Table 12: Coarse Phase Limit Programming (the selected input
clock of other than 2 kHz, 4 kHz and 8 kHz)
WIDE_EN
Coarse Phase Limit
0
1
±1 UI
set by the PH_LOS_COARSE_LIMT[3:0] bits
The DPLL locking status is indicated by the T0_DPLL_LOCK /
T4_DPLL_LOCK bit.
The T4_STS 1 bit will be set when the locking status of the T4 DPLL
changes (from ‘lock’ to ‘unlock’ or from ‘unlock’ to ‘lock’). If the T4_STS 2
bit is ‘1’, an interrupt will be generated.
The occurrence of the coarse phase loss will result in T0/T4 DPLL
unlocked if the COARSE_PH_LOS_LIMT_EN bit is ‘1’.
Functional Description
LOCKING STATUS
The DPLL locking status depends on the locking monitoring results.
The DPLL is in locked state if none of the following events is triggered
during 2 seconds; otherwise, the DPLL is unlocked.
• Fast Loss (the FAST_LOS_SW bit is ‘1’);
• Coarse Phase Loss (the COARSE_PH_LOS_LIMT_EN bit is
‘1’);
• Fine Phase Loss (the FINE_PH_LOS_LIMT_EN bit is ‘1’);
• DPLL Hard Alarm (the FREQ_LIMT_PH_LOS bit is ‘1’).
Table 11: Coarse Phase Limit Programming (the selected input
clock of 2 kHz, 4 kHz or 8 kHz)
MULTI_PH_8K_4K
WIDE_EN
_2K_EN
Hard Limit Exceeding
Two limits are available for this monitoring. They are DPLL soft limit
and DPLL hard limit. When the frequency of the DPLL output with
respect to the master clock exceeds the DPLL soft / hard limit, a DPLL
soft / hard alarm will be raised; the alarm is cleared once the frequency
is within the corresponding limit. The occurrence of the DPLL soft alarm
does not affect the T0/T4 DPLL locking status. The DPLL soft alarm is
indicated by the corresponding T0_DPLL_SOFT_FREQ_ALARM /
T4_DPLL_SOFT_FREQ_ALARM bit. The occurrence of the DPLL hard
alarm will result in T0/T4 DPLL unlocked if the FREQ_LIMT_PH_LOS bit
is ‘1’.
Fast Loss
3.7.1.2
Fine Phase Loss
24
December 3, 2008
IDT82V3255
3.7.3
WAN PLL
• Be cleared when a ‘1’ is written to the corresponding
INn_CMOS_PH_LOCK_ALARM
/
INn_DIFF_PH_LOCK_
ALARM bit;
• Be cleared after the period (= TIME_OUT_VALUE[5:0] X
MULTI_FACTOR[1:0] in second) which starts from when the
alarm is raised.
PHASE LOCK ALARM (T0 ONLY)
A phase lock alarm will be raised when the selected input clock can
not be locked in T0 DPLL within a certain period. This period can be calculated as follows:
Period (sec.) = TIME_OUT_VALUE[5:0] X MULTI_FACTOR[1:0]
The phase lock alarm is indicated by the corresponding
INn_CMOS_PH_LOCK_ALARM bit (n = 1, 2 or 3) /
INn_DIFF_PH_LOCK_ALARM bit (n = 1 or 2).
The selected input clock with a phase lock alarm is disqualified for T0
DPLL locking.
Note that no phase lock alarm is raised if the T4 selected input clock
can not be locked.
The phase lock alarm can be cleared by the following two ways, as
selected by the PH_ALARM_TIMEOUT bit:
Table 13: Related Bit / Register in Chapter 3.7
Bit
Register
Address (Hex)
PHASE_LOSS_FINE_LIMIT_CNFG
5B *
PHASE_LOSS_COARSE_LIMIT_CNFG
5A *
OPERATING_STS
52
DPLL_FREQ_SOFT_LIMIT_CNFG
65
DPLL_FREQ_HARD_LIMT[15:0]
DPLL_FREQ_HARD_LIMIT[15:8]_CNFG,
DPLL_FREQ_HARD_LIMIT[7:0]_CNFG
67, 66
T4_STS 1
INTERRUPTS3_STS
0F
INTERRUPTS3_ENABLE_CNFG
12
PHASE_ALARM_TIME_OUT_CNFG
08
IN1_IN2_CMOS_STS, IN3_CMOS_STS
IN1_IN2_DIFF_STS
INPUT_MODE_CNFG
T4_T0_REG_SEL_CNFG
44, 47
45
09
07
FAST_LOS_SW
PH_LOS_FINE_LIMT[2:0]
FINE_PH_LOS_LIMT_EN
MULTI_PH_8K_4K_2K_EN
WIDE_EN
PH_LOS_COARSE_LIMT[3:0]
COARSE_PH_LOS_LIMT_EN
T0_DPLL_SOFT_FREQ_ALARM
T4_DPLL_SOFT_FREQ_ALARM
T0_DPLL_LOCK
T4_DPLL_LOCK
DPLL_FREQ_SOFT_LIMT[6:0]
FREQ_LIMT_PH_LOS
2
T4_STS
TIME_OUT_VALUE[5:0]
MULTI_FACTOR[1:0]
INn_CMOS_PH_LOCK_ALARM (n = 1, 2, or 3)
INn_DIFF_PH_LOCK_ALARM (n = 1 or 2)
PH_ALARM_TIMEOUT
T4_T0_SEL
Note: * The setting in the 5A and 5B registers is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit.
Functional Description
25
December 3, 2008
IDT82V3255
3.8
WAN PLL
SELECTED INPUT CLOCK SWITCH
3.8.2
When the device is configured as Automatic input clock selection, T0
input clock switch is different from T4 input clock switch.
If the input clock is selected by External Fast selection or by Forced
selection, it can be switched by setting the related registers (refer to
Chapter 3.6.1 External Fast Selection (T0 only) & Chapter 3.6.2 Forced
Selection) any time. In this case, whether the input clock is qualified for
DPLL locking does not affect the clock switch. If the T4 selected input
clock is a T0 DPLL output, it can only be switched by setting the
T0_FOR_T4 bit.
For T0 path, Revertive and Non-Revertive switches are supported,
as selected by the REVERTIVE_MODE bit.
For T4 path, only Revertive switch is supported.
The difference between Revertive and Non-Revertive switches is
that whether the selected input clock is switched when another qualified
input clock with a higher priority than the current selected input clock is
available for selection. In Non-Revertive switch, input clock switch is
minimized.
When the input clock is selected by Automatic selection, the input
clock switch depends on its validity and priority. If the current selected
input clock is disqualified, a new qualified input clock may be switched
to.
3.8.1
Conditions of the qualified input clocks available for T0 selection are
different from that for T4 selection, as shown in Table 14:
INPUT CLOCK VALIDITY
For all the input clocks, the validity depends on the results of input
clock quality monitoring (refer to Chapter 3.5 Input Clock Quality Monitoring). When all of the following conditions are satisfied, the input clock
is valid; otherwise, it is invalid.
• No no-activity alarm (the INn_CMOS_NO_ACTIVITY_ALARM /
INn_DIFF_NO_ACTIVITY_ALARM bit is ‘0’);
• No frequency hard alarm (the INn_CMOS_FREQ_HARD_
ALARM / INn_DIFF_FREQ_HARD_ALARM bit is ‘0’);
• If the IN_NOISE_WINDOW bit is ‘1’, all the edges of the input
clock of 2 kHz, 4 kHz or 8 kHz drift inside ±5%; if the
IN_NOISE_WINDOW bit is ‘0’, this condition is ignored.
Table 14: Conditions of Qualified Input Clocks Available for T0 & T4
Selection
Conditions of Qualified Input Clocks Available for T0 & T4 Selection
• Valid, i.e., the INn_CMOS 1 / INn_DIFF 1 bit is ‘1’;
T0 • Priority enabled, i.e., the corresponding INn_CMOS_SEL
_PRIORITY[3:0] / INn_DIFF_SEL_PRIORITY[3:0] bits are not ‘0000’
• Valid (all the validity conditions listed in Chapter 3.8.1 Input Clock Validity are satisfied);
T4
• Priority enabled, i.e., the corresponding INn_CMOS_SEL
_PRIORITY[3:0] / INn_DIFF_SEL_PRIORITY[3:0] bits are not ‘0000’
The validity qualification of the T0 selected input clock is different
from that of the T4 selected input clock. The validity qualification of the
T4 selected input clock is the same as the above. The T0 selected input
clock is valid when all of the above and the following conditions are satisfied; otherwise, it is invalid.
• No phase lock alarm, i.e., the INn_CMOS_PH_LOCK_ALARM /
INn_DIFF_PH_LOCK_ALARM bit is ‘0’;
• If the ULTR_FAST_SW bit is ‘1’, the T0 selected input clock
misses less than (<) 2 consecutive clock cycles; if the
ULTR_FAST_SW bit is ‘0’, this condition is ignored.
The input clock is disqualified if any of the above conditions is not
satisfied.
In summary, the selected input clock can be switched by:
• External Fast selection (supported by T0 path only);
• Forced selection;
• Revertive switch;
• Non-Revertive switch (supported by T0 path only);
• T4 DPLL locked to T0 DPLL output (supported by T4 path only).
3.8.2.1
The validities of all the input clocks are indicated by the INn_CMOS 1
bit (n = 1, 2 or 3) / INn_DIFF 1 bit (n = 1 or 2). When the input clock validity changes (from ‘valid’ to ‘invalid’ or from ‘invalid’ to ‘valid’), the
INn_CMOS 2 / INn_DIFF 2 bit will be set. If the INn_CMOS 3 / INn_DIFF
3
bit is ‘1’, an interrupt will be generated.
Revertive Switch
In Revertive switch, the selected input clock is switched when
another qualified input clock with a higher priority than the current
selected input clock is available.
The selected input clock is switched if any of the following is satisfied:
• the selected input clock is disqualified;
• another qualified input clock with a higher priority than the
selected input clock is available.
When the T0 selected input clock has failed, i.e., the validity of the T0
selected input clock changes from ‘valid’ to ‘invalid’, the
T0_MAIN_REF_FAILED 1 bit will be set. If the T0_MAIN_REF_FAILED 2
bit is ‘1’, an interrupt will be generated. This interrupt can also be indicated by hardware - the TDO pin, as determined by the
LOS_FLAG_TO_TDO bit. When the TDO pin is used to indicate this
interrupt, it will be set high when this interrupt is generated and will
remain high until this interrupt is cleared.
Functional Description
SELECTED INPUT CLOCK SWITCH
A qualified input clock with the highest priority is selected by revertive
switch. If more than one qualified input clock is available and has the
same priority, the input clock with the smallest ‘n’ is selected. See
Table 9 for the ‘n’ assigned to each input clock.
26
December 3, 2008
IDT82V3255
3.8.2.2
WAN PLL
The qualified input clocks with the three highest priorities are indicated by HIGHEST_PRIORITY_VALIDATED[3:0] bits, the SECOND_
PRIORITY_VALIDATED[3:0] bits and the THIRD_PRIORITY
_VALIDATED[3:0] bits respectively. If more than one input clock has the
same priority, the input clock with the smallest ‘n’ is indicated by the
HIGHEST_PRIORITY_VALIDATED[3:0] bits. See Table 9 for the ‘n’
assigned to the input clock.
Non-Revertive Switch (T0 only)
In Non-Revertive switch, the T0 selected input clock is not switched
when another qualified input clock with a higher priority than the current
selected input clock is available. In this case, the selected input clock is
switched and a qualified input clock with the highest priority is selected
only when the T0 selected input clock is disqualified. If more than one
qualified input clock is available and has the same priority, the input
clock with the smallest ‘n’ is selected. See Table 9 for the ‘n’ assigned to
each input clock.
3.8.3
When the device is configured in Automatic selection and Revertive
switch is enabled, the input clock indicated by the
CURRENTLY_SELECTED_INPUT[3:0] bits is the same as the one indicated by the HIGHEST_PRIORITY_VALIDATED[3:0] bits; otherwise,
they are not the same.
SELECTED / QUALIFIED INPUT CLOCKS INDICATION
The
selected
input
clock
is
indicated
by
the
CURRENTLY_SELECTED_INPUT[3:0] bits. Note if the T4 selected
input clock is a T0 DPLL output, it can not be indicated by these bits.
When all the input clocks for T4 path changes to be unqualified, the
INPUT_TO_T4 1 bit will be set. If the INPUT_TO_T4 2 bit is ‘1’, an interrupt will be generated.
Table 15: Related Bit / Register in Chapter 3.8
Bit
Register
Address (Hex)
T0_FOR_T4
T4_INPUT_SEL_CNFG
51
INn_CMOS 1 (n = 1, 2 or 3) / INn_DIFF 1 (n = 1 or 2)
INPUT_VALID1_STS, INPUT_VALID2_STS
4A, 4B
INn_CMOS 2 (n = 1, 2 or 3) / INn_DIFF 2 (n = 1 or 2)
INTERRUPTS1_STS, INTERRUPTS2_STS
0D, 0E
INTERRUPTS1_ENABLE_CNFG, INTERRUPTS2_ENABLE_CNFG
10, 11
IN1_IN2_CMOS_STS, IN3_CMOS_STS
44, 47
IN1_IN2_DIFF_STS
45
PHASE_MON_PBO_CNFG
78
MON_SW_PBO_CNFG
0B
T0_MAIN_REF_FAILED 1
INTERRUPTS2_STS
0E
T0_MAIN_REF_FAILED 2
INn_CMOS
3 (n = 1, 2 or 3) / INn_DIFF 3 (n = 1 or 2)
INn_CMOS_NO_ACTIVITY_ALARM (n = 1, 2 or 3)
INn_CMOS_FREQ_HARD_ALARM (n = 1, 2 or 3)
INn_CMOS_PH_LOCK_ALARM (n = 1, 2 or 3)
INn_DIFF_NO_ACTIVITY_ALARM (n = 1 or 2)
INn_DIFF_FREQ_HARD_ALARM (n = 1 or 2)
INn_DIFF_PH_LOCK_ALARM (n = 1 or 2)
IN_NOISE_WINDOW
ULTR_FAST_SW
LOS_FLAG_TO_TDO
INPUT_TO_T4
INTERRUPTS2_ENABLE_CNFG
11
1
INTERRUPTS3_STS
0F
2
INTERRUPTS3_ENABLE_CNFG
12
INPUT_MODE_CNFG
IN1_IN2_CMOS_SEL_PRIORITY_CNFG, IN3_CMOS_SEL_PRIORITY_CNFG
IN1_IN2_DIFF_SEL_PRIORITY_CNFG
09
27 *, 2A *
28 *
PRIORITY_TABLE1_STS
4E *
PRIORITY_TABLE2_STS
4F *
T4_T0_REG_SEL_CNFG
07
INPUT_TO_T4
REVERTIVE_MODE
INn_CMOS_SEL_PRIORITY[3:0] (n = 1, 2 or 3)
INn_DIFF_SEL_PRIORITY[3:0] (n = 1 or 2)
CURRENTLY_SELECTED_INPUT[3:0]
HIGHEST_PRIORITY_VALIDATED[3:0]
SECOND_PRIORITY_VALIDATED[3:0]
THIRD_PRIORITY_VALIDATED[3:0]
T4_T0_SEL
Note: * The setting in the 27, 28, 2A, 4E and 4F registers is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit.
Functional Description
27
December 3, 2008
IDT82V3255
3.9
WAN PLL
SELECTED INPUT CLOCK STATUS VS. DPLL
OPERATING MODE
3.9.1
The T0 DPLL operating mode is controlled
T0_OPERATING_MODE[2:0] bits, as shown in Table 16:
The operating modes supported by T0 DPLL are more complex than
the ones supported by T4 DPLL for T0 path is the main one. T0 DPLL
supports three primary operating modes: Free-Run, Locked and Holdover, and three secondary, temporary operating modes: Pre-Locked,
Pre-Locked2 and Lost-Phase. T4 DPLL supports three operating
modes: Free-Run, Locked and Holdover. The operating modes of T0
DPLL and T4 DPLL can be switched automatically or by force, as controlled by the T0_OPERATING_MODE[2:0] / T4_OPERATING_
MODE[2:0] bits respectively.
by
the
Table 16: T0 DPLL Operating Mode Control
When the operating mode is switched by force, the operating mode
switch is under external control and the status of the selected input clock
takes no effect to the operating mode selection. The forced operating
mode switch is applicable for special cases, such as testing.
T0_OPERATING_MODE[2:0]
T0 DPLL Operating Mode
000
001
010
100
101
110
111
Automatic
Forced - Free-Run
Forced - Holdover
Forced - Locked
Forced - Pre-Locked2
Forced - Pre-Locked
Forced - Lost-Phase
When the operating mode is switched automatically, the operation of
the internal state machine is shown in Figure 6.
When the operating mode is switched automatically, the internal
state machines for T0 and for T4 automatically determine the operating
mode respectively.
Functional Description
T0 SELECTED INPUT CLOCK VS. DPLL OPERATING
MODE
Whether the operating mode is under external control or is switched
automatically, the current operating mode is always indicated by the
T0_DPLL_OPERATING_MODE[2:0] bits. When the operating mode
switches, the T0_OPERATING_MODE 1 bit will be set. If the
T0_OPERATING_MODE 2 bit is ‘1’, an interrupt will be generated.
28
December 3, 2008
IDT82V3255
WAN PLL
1
Free-Run mode
3
2
Pre-Locked
mode
4
5
Locked
mode
10
9
15
Pre-Locked2
mode
8
6
Holdover
mode
7
11
12
Lost-Phase
mode
13
14
Figure 6. T0 Selected Input Clock vs. DPLL Automatic Operating Mode
Notes to Figure 6:
1. Reset.
2. An input clock is selected.
3. The T0 selected input clock is disqualified AND No qualified input clock is available.
4. The T0 selected input clock is switched to another one.
5. The T0 selected input clock is locked (the T0_DPLL_LOCK bit is ‘1’).
6. The T0 selected input clock is disqualified AND No qualified input clock is available.
7. The T0 selected input clock is unlocked (the T0_DPLL_LOCK bit is ‘0’).
8. The T0 selected input clock is locked again (the T0_DPLL_LOCK bit is ‘1’).
9. The T0 selected input clock is switched to another one.
10. The T0 selected input clock is locked (the T0_DPLL_LOCK bit is ‘1’).
11. The T0 selected input clock is disqualified AND No qualified input clock is available.
12. The T0 selected input clock is switched to another one.
13. The T0 selected input clock is disqualified AND No qualified input clock is available.
14. An input clock is selected.
15. The T0 selected input clock is switched to another one.
Functional Description
29
December 3, 2008
IDT82V3255
WAN PLL
Notes to Figure 7:
1. Reset.
2. An input clock is selected.
3. (The T4 selected input clock is disqualified) OR (A qualified input
clock with a higher priority is switched to) OR (The T4 selected
input clock is switched to another one by Forced selection) OR
(When T4 DPLL locks to the T0 DPLL output, the T4 selected
input clock is switched by setting the T0_FOR_T4 bit).
4. An input clock is selected.
5. No input clock is selected.
The causes of Item 4, 9, 12, 15 - ‘the T0 selected input clock is
switched to another one’ - are: (The T0 selected input clock is disqualified AND Another input clock is switched to) OR (In Revertive switch, a
qualified input clock with a higher priority is switched to) OR (The T0
selected input clock is switched to another one by External Fast selection or Forced selection).
Refer to Table 14 for details about the input clock qualification for T0
path.
3.9.2
T4 SELECTED INPUT CLOCK VS. DPLL OPERATING
MODE
The T4 DPLL operating mode is controlled
T4_OPERATING_MODE[2:0] bits, as shown in Table 17:
by
Refer to Table 14 for details about the input clock qualification for T4
path.
the
Table 18: Related Bit / Register in Chapter 3.9
Table 17: T4 DPLL Operating Mode Control
T4_OPERATING_MODE[2:0]
T4 DPLL Operating Mode
000
001
010
100
Automatic
Forced - Free-Run
Forced - Holdover
Forced - Locked
Bit
Address
(Hex)
Register
T0_OPERATING_MODE[2:0] T0_OPERATING_MODE_CNFG
T4_OPERATING_MODE[2:0] T4_OPERATING_MODE_CNFG
T0_DPLL_OPERATING_MOD
E[2:0]
OPERATING_STS
T0_DPLL_LOCK
When the operating mode is switched automatically, the operation of
the internal state machine is shown in Figure 7:
T0_OPERATING_MODE 1
T0_OPERATING_MODE
T0_FOR_T4
1
2
53
54
52
INTERRUPTS2_STS
0E
INTERRUPTS2_ENABLE_CNFG
11
T4_INPUT_SEL_CNFG
51
Free-Run mode
2
Locked mode
3
4
Holdover
mode
5
Figure 7. T4 Selected Input Clock vs. DPLL Automatic
Operating Mode
Functional Description
30
December 3, 2008
IDT82V3255
3.10
WAN PLL
T0 / T4 DPLL OPERATING MODE
3.10.1.1
In Free-Run mode, the T0 DPLL output refers to the master clock
and is not affected by any input clock. The accuracy of the T0 DPLL output is equal to that of the master clock.
The T0/T4 DPLL gives a stable performance in different applications
without being affected by operating conditions or silicon process variations. It integrates a PFD (Phase & Frequency Detector), a LPF (Low
Pass Filter) and a DCO (Digital Controlled Oscillator), which forms a
closed loop. If no input clock is selected, the loop is not closed, and the
PFD and LPF do not function.
3.10.1.2
Pre-Locked Mode
In Pre-Locked mode, the T0 DPLL output attempts to track the
selected input clock.
The PFD detects the phase error, including the fast loss, coarse
phase loss and fine phase loss (refer to Chapter 3.7.1.1 Fast Loss to
Chapter 3.7.1.3 Fine Phase Loss). The averaged phase error of the T0/
T4 DPLL feedback with respect to the selected input clock is indicated
by the CURRENT_PH_DATA[15:0] bits. It can be calculated as follows:
The Pre-Locked mode is a secondary, temporary mode.
3.10.1.3
Locked Mode
In Locked mode, the T0 selected input clock is locked. The phase
and frequency offset of the T0 DPLL output track those of the T0
selected input clock.
Averaged Phase Error (ns) = CURRENT_PH_DATA[15:0] X 0.61
The LPF filters jitters. Its 3 dB bandwidth and damping factor are programmable. A range of bandwidths and damping factors can be set to
meet different application requirements. Generally, the lower the damping factor is, the longer the locking time is and the more the gain is.
In this mode, if the T0 selected input clock is in fast loss status and
the FAST_LOS_SW bit is ‘1’, the T0 DPLL is unlocked (refer to
Chapter 3.7.1.1 Fast Loss) and will enter Lost-Phase mode when the
operating mode is switched automatically; if the T0 selected input clock
is in fast loss status and the FAST_LOS_SW bit is ‘0’, the T0 DPLL locking status is not affected and the T0 DPLL will enter Temp-Holdover
mode automatically.
The DCO controls the DPLL output. The frequency of the DPLL output is always multiplied on the basis of the master clock. The phase and
frequency offset of the DPLL output may be locked to those of the
selected input clock. The current frequency offset with respect to the
master clock is indicated by the CURRENT_DPLL_FREQ[23:0] bits, and
can be calculated as follows:
3.10.1.3.1 Temp-Holdover Mode
The T0 DPLL will automatically enter Temp-Holdover mode with a
selected input clock switch or no qualified input clock available when the
operating mode switch is under external control.
Current Frequency Offset (ppm) = CURRENT_DPLL_FREQ[23:0] X
0.000011
3.10.1
Free-Run Mode
In Temp-Holdover mode, the T0 DPLL has temporarily lost the
selected input clock. The T0 DPLL operation in Temp-Holdover mode
and that in Holdover mode are alike (refer to Chapter 3.10.1.5 Holdover
Mode) except the frequency offset acquiring methods. See
Chapter 3.10.1.5 Holdover Mode for details about the methods. The
method is selected by the TEMP_HOLDOVER_MODE[1:0] bits, as
shown in Table 19:
T0 DPLL OPERATING MODE
The T0 DPLL loop is closed except in Free-Run mode and Holdover
mode.
For a closed loop, different bandwidths and damping factors can be
used depending on DPLL locking stages: starting, acquisition and
locked.
In the first two seconds when the T0 DPLL attempts to lock to the
selected input clock, the starting bandwidth and damping factor are
used. They are set by the T0_DPLL_START_BW[4:0] bits and the
T0_DPLL_START_DAMPING[2:0] bits respectively.
Table 19: Frequency Offset Control in Temp-Holdover Mode
TEMP_HOLDOVER_MODE[1:0]
Frequency Offset Acquiring Method
00
01
10
11
the same as that used in Holdover mode
Automatic Instantaneous
Automatic Fast Averaged
Automatic Slow Averaged
During the acquisition, the acquisition bandwidth and damping factor
are used. They are set by the T0_DPLL_ACQ_BW[4:0] bits and the
T0_DPLL_ACQ_DAMPING[2:0] bits respectively.
When the T0 selected input clock is locked, the locked bandwidth
and damping factor are used. They are set by the
T0_DPLL_LOCKED_BW[4:0]
bits
and
the
T0_DPLL_LOCKED_DAMPING[2:0] bits respectively.
The device automatically controls the T0 DPLL to exit from TempHoldover mode.
3.10.1.4
Lost-Phase Mode
The corresponding bandwidth and damping factor are used when the
T0 DPLL operates in different DPLL locking stages: starting, acquisition
and locked, as controlled by the device automatically.
In Lost-Phase mode, the T0 DPLL output attempts to track the
selected input clock.
Only the locked bandwidth and damping factor can be used regardless of the T0 DPLL locking stage, as controlled by the AUTO_BW_SEL
bit.
3.10.1.5
Functional Description
The Lost-Phase mode is a secondary, temporary mode.
Holdover Mode
In Holdover mode, the T0 DPLL resorts to the stored frequency data
acquired in Locked mode to control its output. The T0 DPLL output is not
31
December 3, 2008
IDT82V3255
WAN PLL
phase locked to any input clock. The frequency offset acquiring method
is selected by the MAN_HOLDOVER bit, the AUTO_AVG bit and the
FAST_AVG bit, as shown in Table 20:
Table 20: Frequency Offset Control in Holdover Mode
MAN_HOLDOVER
AUTO_AVG
FAST_AVG
Frequency Offset Acquiring Method
0
don’t-care
0
1
Automatic Instantaneous
Automatic Slow Averaged
Automatic Fast Averaged
Manual
0
1
1
don’t-care
3.10.1.5.1 Automatic Instantaneous
Table 21: Holdover Frequency Offset Read
By this method, the T0 DPLL freezes at the operating frequency
when it enters Holdover mode. The accuracy is 4.4X10-8 ppm.
READ_AVG FAST_AVG
3.10.1.5.2 Automatic Slow Averaged
0
By this method, an internal IIR (Infinite Impulse Response) filter is
employed to get the frequency offset. The IIR filter gives a 3 dB attenuation point corresponding to a period of 110 minutes. The accuracy is
1.1X10-5 ppm.
1
3.10.1.5.3 Automatic Fast Averaged
don’t-care The value is equal to the one written to.
The value is acquired by Automatic Slow Averaged
0
method, not equal to the one written to.
The value is acquired by Automatic Fast Averaged
1
method, not equal to the one written to.
The frequency offset in ppm is calculated as follows:
Holdover Frequency Offset (ppm) = T0_HOLDOVER_FREQ[23:0] X
0.000011
By this method, an internal IIR (Infinite Impulse Response) filter is
employed to get the frequency offset. The IIR filter gives a 3 dB attenuation point corresponding to a period of 8 minutes. The accuracy is
1.1X10-5 ppm.
3.10.1.6
Pre-Locked2 Mode
In Pre-Locked2 mode, the T0 DPLL output attempts to track the
selected input clock.
3.10.1.5.4 Manual
By this method, the frequency offset is set by
T0_HOLDOVER_FREQ[23:0] bits. The accuracy is 1.1X10-5 ppm.
Offset Value Read from
T0_HOLDOVER_FREQ[23:0]
The Pre-Locked2 mode is a secondary, temporary mode.
the
3.10.2
The frequency offset of the T0 DPLL output is indicated by the
CURRENT_DPLL_FREQ[23:0] bits.
T4 DPLL OPERATING MODE
The T4 path is simpler compared with the T0 path.
3.10.2.1
The device provides a reference for the value to be written to the
T0_HOLDOVER_FREQ[23:0] bits. The value to be written can refer to
the value read from the CURRENT_DPLL_FREQ[23:0] bits or the
T0_HOLDOVER_FREQ[23:0] bits (refer to Chapter 3.10.1.5.5 Holdover
Frequency Offset Read); or then be processed by external software filtering.
Free-Run Mode
In Free-Run mode, the T4 DPLL output refers to the master clock
and is affected by any input clock. The accuracy of the T4 DPLL output
is equal to that of the master clock.
3.10.2.2
Locked Mode
3.10.1.5.5 Holdover Frequency Offset Read
In Locked mode, the T4 selected input clock may be locked in the T4
DPLL.
The offset value, which is acquired by Automatic Slow Averaged,
Automatic Fast Averaged and is set by related register bits, can be read
from the T0_HOLDOVER_FREQ[23:0] bits by setting the READ_AVG
bit and the FAST_AVG bit, as shown in Table 21.
When the T4 selected input clock is locked, the phase and frequency
offset of the T4 DPLL output track those of the T4 selected input clock;
when unlocked, the phase and frequency offset of the T4 DPLL output
attempt to track those of the selected input clock.
The T4 DPLL loop is closed in Locked mode. Its bandwidth and
damping factor are set by the T4_DPLL_LOCKED_BW[1:0] bits and the
T4_DPLL_LOCKED_DAMPING[2:0] bits respectively.
3.10.2.3
Holdover Mode
In Holdover mode, the T4 DPLL resorts to the stored frequency data
acquired in Locked mode to control its output. The T4 DPLL output is not
Functional Description
32
December 3, 2008
IDT82V3255
WAN PLL
phase locked to any input clock. The T4 DPLL freezes at the operating
frequency when it enters Holdover mode. The accuracy is 4.4X10-8
ppm.
Table 22: Related Bit / Register in Chapter 3.10
Bit
Register
Address (Hex)
CURRENT_PH_DATA[15:0]
CURRENT_DPLL_PHASE[15:8]_STS, CURRENT_DPLL_PHASE[7:0]_STS
CURRENT_DPLL_FREQ[23:16]_STS, CURRENT_DPLL_FREQ[15:8]_STS,
CURRENT_DPLL_FREQ[7:0]_STS
69 *, 68 *
CURRENT_DPLL_FREQ[23:0]
T0_DPLL_START_BW[4:0]
T0_DPLL_START_DAMPING[2:0]
T0_DPLL_ACQ_BW[4:0]
T0_DPLL_ACQ_DAMPING[2:0]
T0_DPLL_LOCKED_BW[4:0]
T0_DPLL_LOCKED_DAMPING[2:0]
AUTO_BW_SEL
FAST_LOS_SW
TEMP_HOLDOVER_MODE[1:0]
MAN_HOLDOVER
AUTO_AVG
FAST_AVG
READ_AVG
T0_HOLDOVER_FREQ[23:0]
T4_DPLL_LOCKED_BW[1:0]
T4_DPLL_LOCKED_DAMPING[2:0]
T4_T0_SEL
64 *, 63 *, 62 *
T0_DPLL_START_BW_DAMPING_CNFG
56
T0_DPLL_ACQ_BW_DAMPING_CNFG
57
T0_DPLL_LOCKED_BW_DAMPING_CNFG
58
T0_BW_OVERSHOOT_CNFG
PHASE_LOSS_FINE_LIMIT_CNFG
59
5B *
T0_HOLDOVER_MODE_CNFG
5C
T0_HOLDOVER_FREQ[23:16]_CNFG, T0_HOLDOVER_FREQ[15:8]_CNFG,
T0_HOLDOVER_FREQ[7:0]_CNFG
5F, 5E, 5D
T4_DPLL_LOCKED_BW_DAMPING_CNFG
61
T4_T0_REG_SEL_CNFG
07
Note: * The setting in the 5B, 62 ~ 64, 68 and 69 registers is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit.
Functional Description
33
December 3, 2008
IDT82V3255
3.11
WAN PLL
T0 / T4 DPLL OUTPUT
1.0 µs but less than 3.5 µs that occur over an interval of less than 0.1
seconds may or may not be built-out.
The DPLL output is locked to the selected input clock. According to
the phase-compared result of the feedback and the selected input clock,
and the DPLL output frequency offset, the PFD output is limited and the
DPLL output is frequency offset limited.
3.11.1
An integrated Phase Transient Monitor can be enabled by the
PH_MON_EN bit to monitor the phase-time changes on the T0 selected
input clock. When the phase-time changes are greater than a limit over
an interval of less than 0.1 seconds, a PBO event is triggered and the
phase transients on the DPLL output are absorbed. The limit is programmed by the PH_TR_MON_LIMT[3:0] bits, and can be calculated as
follows:
PFD OUTPUT LIMIT
The PFD output is limited to be within ±1 UI or within the coarse
phase limit (refer to Chapter 3.7.1.2 Coarse Phase Loss), as determined
by the MULTI_PH_APP bit.
3.11.2
Limit (ns) = (PH_TR_MON_LIMT[3:0] + 7) X 156
The phase offset induced by PBO will never result in a coarse or fine
phase loss.
FREQUENCY OFFSET LIMIT
The DPLL output is limited to be within the DPLL hard limit (refer to
Chapter 3.7.1.4 Hard Limit Exceeding).
3.11.4
The phase offset of the T0 selected input clock with respect to the T0
DPLL output can be adjusted. The PH_OFFSET_EN bit determines
whether the input-to-output phase offset is enabled. If enabled, the
input-to-output phase offset can be adjusted by setting the
PH_OFFSET[9:0] bits.
For T0 DPLL, the integral path value can be frozen when the DPLL
hard limit is reached. This function, enabled by the T0_LIMT bit, will minimize the subsequent overshoot when T0 DPLL is pulling in.
3.11.3
PBO (T0 ONLY)
The PBO function is only supported by the T0 path.
The input-to-output phase offset can be calculated as follows:
When a PBO event is triggered, the phase offset of the selected input
clock with respect to the T0 DPLL output is measured. The device then
automatically accounts for the measured phase offset and compensates
an appropriate phase offset into the DPLL output so that the phase transients on the T0 DPLL output are minimized.
Phase Offset (ns) = PH_OFFSET[9:0] X 0.61
3.11.5
FOUR PATHS OF T0 / T4 DPLL OUTPUTS
The T0 DPLL output and the T4 DPLL output are phase aligned with
the T0 selected input clock and the T4 selected input clock respectively
every 125 µs period. Each DPLL has four output paths.
A PBO event is triggered if any one of the following conditions
occurs:
• T0 selected input clock switches (the PBO_EN bit is ‘1’);
• T0 DPLL exits from Holdover mode or Free-Run mode (the
PBO_EN bit is ‘1’);
• Phase-time changes on the T0 selected input clock are greater
than a programmable limit over an interval of less than 0.1 seconds (the PH_MON_PBO_EN bit is ‘1’).
3.11.5.1
T0 Path
The four paths for T0 DPLL output are as follows:
• 77.76 MHz path - outputs a 77.76 MHz clock;
• 16E1/16T1 path - outputs a 16E1 or 16T1 clock, as selected by
the IN_SONET_SDH bit;
• GSM/OBSAI/16E1/16T1 path - outputs a GSM, OBSAI, 16E1 or
16T1 clock, as selected by the T0_GSM_OBSAI_16E1_16T1_
SEL[1:0] bits;
• 12E1/24T1/E3/T3 path - outputs a 12E1, 24T1, E3 or T3 clock,
as selected by the T0_12E1_24T1_E3_T3_SEL[1:0] bits.
For the first two conditions, the phase transients on the T0 DPLL output are minimized to be no more than 0.61 ns with PBO. The PBO can
also be frozen at the current phase offset by setting the PBO_FREZ bit.
When the PBO is frozen, the device will ignore any further PBO events
triggered by the above two conditions, and maintain the current phase
offset. When the PBO is disabled, there may be a phase shift on the T0
DPLL output and the T0 DPLL output tracks back to 0 degree phase offset with respect to the T0 selected input clock.
T0 selected input clock is compared with a T0 DPLL output for DPLL
locking. The output can only be derived from the 77.76 MHz path or the
16E1/16T1 path. The output path is automatically selected and the output is automatically divided to get the same frequency as the T0
selected input clock.
The last condition is specially for stratum 2 and 3E clocks. The PBO
requirement specified in the Telcordia GR-1244-CORE is: ‘Input phasetime changes of 3.5 µs or greater over an interval of less than 0.1 seconds or less shall be built-out by stratum 2 and 3E clocks to reduce the
resulting clock phase-time change to less than 50 ns. Phase-time
changes of 1.0 µs or less over an interval of 0.1 seconds shall not be
built-out.’ Based on this requirement, phase-time changes of more than
Functional Description
PHASE OFFSET SELECTION (T0 ONLY)
The T0 DPLL 77.76 MHz output or an 8 kHz signal derived from it
can be provided for the T4 DPLL input clock selection (refer to
Chapter 3.6 T0 / T4 DPLL Input Clock Selection).
T0 DPLL outputs are provided for T0/T4 APLL or device output process.
34
December 3, 2008
IDT82V3255
3.11.5.2
WAN PLL
16E1/16T1 path. In this case, the output path is automatically selected
and the output is automatically divided to get the same frequency as the
T4 selected input clock.
T4 Path
The four paths for T4 DPLL output are as follows:
• 77.76 MHz path - outputs a 77.76 MHz clock;
• 16E1/16T1 path - outputs a 16E1 or 16T1 clock, as selected by
the IN_SONET_SDH bit;
• GSM/GPS/16E1/16T1 path - outputs a GSM, GPS, 16E1 or
16T1 clock, as selected by the T4_GSM_GPS_16E1_16T1_
SEL[1:0] bits;
• 12E1/24T1/E3/T3 path - outputs a 12E1, 24T1, E3 or T3 clock,
as selected by the T4_12E1_24T1_E3_T3_SEL[1:0] bits.
In addition, T4 selected input clock is compared with the T0 selected
input clock to get the phase difference between T0 and T4 selected input
clocks, as determined by the T4_TEST_T0_PH bit.
T4 DPLL outputs are provided for T0/T4 APLL or device output process.
T4 selected input clock is compared with a T4 DPLL output for DPLL
locking. The output can be derived from the 77.76 MHz path or the
Table 23: Related Bit / Register in Chapter 3.11
Bit
Register
Address (Hex)
MULTI_PH_APP
T0_LIMT
PBO_EN
PBO_FREZ
PH_MON_PBO_EN
PH_MON_EN
PH_TR_MON_LIMT[3:0]
PH_OFFSET_EN
PH_OFFSET[9:0]
IN_SONET_SDH
T0_GSM_OBSAI_16E1_16T1_SEL[1:0]
T0_12E1_24T1_E3_T3_SEL[1:0]
T4_GSM_GPS_16E1_16T1_SEL[1:0]
T4_12E1_24T1_E3_T3_SEL[1:0]
T4_TEST_T0_PH
T4_T0_SEL
PHASE_LOSS_COARSE_LIMIT_CNFG
T0_BW_OVERSHOOT_CNFG
5A *
59
MON_SW_PBO_CNFG
0B
PHASE_MON_PBO_CNFG
78
PHASE_OFFSET[9:8]_CNFG
PHASE_OFFSET[9:8]_CNFG, PHASE_OFFSET[7:0]_CNFG
INPUT_MODE_CNFG
7B
7B, 7A
09
T0_DPLL_APLL_PATH_CNFG
55
T4_DPLL_APLL_PATH_CNFG
60
T4_INPUT_SEL_CNFG
T4_T0_REG_SEL_CNFG
51
07
Note: * The setting in the 5A register is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit.
Functional Description
35
December 3, 2008
IDT82V3255
3.12
WAN PLL
T0 / T4 APLL
3.13
OUTPUT CLOCKS & FRAME SYNC SIGNALS
A T0 APLL and a T4 APLL are provided for a better jitter and wander
performance of the device output clocks.
The device supports 2 output clocks and 2 frame sync output signals
altogether.
The bandwidths of the T0/T4 APLL are set by the T0_APLL_BW[1:0]
/ T4_APLL_BW[1:0] bits respectively. The lower the bandwidth is, the
better the jitter and wander performance of the T0/T4 APLL output are.
3.13.1
The device provides 2 output clocks.
OUT1 outputs a PECL or LVDS signal, as selected by the
OUT1_PECL_LVDS bit. OUT2 outputs a CMOS signal.
The input of the T0/T4 APLL can be derived from one of the T0 and
T4 DPLL outputs, as selected by the T0_APLL_PATH[3:0] /
T4_APLL_PATH[3:0] bits respectively.
The outputs on OUT1 and OUT2 are variable, depending on the signals derived from the T0/T4 DPLL and T0/T4 APLL outputs, and the corresponding OUTn_PATH_SEL[3:0] bits (n = 1 or 2). The derived signal
can be from the T0/T4 DPLL and T0/T4 APLL outputs, as selected by
the corresponding OUTn_PATH_SEL[3:0] bits (n = 1 or 2). If the signal is
derived from one of the T0/T4 DPLL outputs, please refer to Table 25 for
the output frequency. If the signal is derived from the T0/T4 APLL output,
please refer to Table 26 for the output frequency.
Both the APLL and DPLL outputs are provided for selection for the
device output.
Table 24: Related Bit / Register in Chapter 3.12
Bit
T0_APLL_BW[1:0]
T4_APLL_BW[1:0]
T0_APLL_PATH[3:0]
T4_APLL_PATH[3:0]
Register
Address (Hex)
T0_T4_APLL_BW_CNFG
6A
T0_DPLL_APLL_PATH_CNFG
T4_DPLL_APLL_PATH_CNFG
55
60
OUTPUT CLOCKS
The outputs on OUT1 and OUT2 can be inverted, as determined by
the corresponding OUTn_INV bit (n = 1 or 2).
Both the output clocks derived from T0/T4 selected input clock are
aligned with the T0/T4 selected input clock respectively every 125 µs
period.
Table 25: Outputs on OUT1 & OUT2 if Derived from T0/T4 DPLL Outputs
OUTn_DIVIDER[3:0]
(Output Divider) 1
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
outputs on OUT1 & OUT2 if derived from T0/T4 DPLL outputs 2
77.76 MHz
12E1
16E1
24T1
16T1
E3
T3
GSM
(26 MHz)
OBSAI
(30.72 MHz)
GPS
(40 MHz)
13 MHz
15.36 MHz
20
10
Output is disabled (output low).
12E1
6E1
3E1
2E1
16E1
8E1
4E1
2E1
E1
24T1
12T1
6T1
4T1
3T1
2T1
16T1
8T1
4T1
E3
2T1
E1
T3
5
T1
T1
64 kHz
8 kHz
2 kHz
400 Hz
1Hz
Output is disabled (output high).
Note:
1. n = 1 or 2. Each output is assigned a frequency divider.
2. E1 = 2.048 MHz, T1 = 1.544 MHz, E3 = 34.368 MHz, T3 = 44.736 MHz. The blank cell means the configuration is reserved.
Functional Description
36
December 3, 2008
IDT82V3255
WAN PLL
Table 26: Outputs on OUT1 & OUT2 if Derived from T0/T4 APLL
OUTn_DIVIDER[3:0]
(Output Divider) 1 77.76 MHz X 4 12E1 X 4
outputs on OUT1 & OUT2 if derived from T0/T4 APLL output 2
16E1 X 4
24T1 X 4
0000
T3
GSM
OBSAI
(26 MHz X 2) (30.72 MHz X 10)
GPS
(40 MHz)
Output is disabled (output low).
622.08 MHz
0010
311.04 MHz 3
155.52 MHz
77.76 MHz
51.84 MHz
38.88 MHz
25.92 MHz
19.44 MHz
1001
48E1
64E1
96T1
64T1
24E1
12E1
8E1
6E1
4E1
3E1
32E1
16E1
48T1
24T1
16T1
12T1
8T1
6T1
32T1
16T1
8E1
4E1
2E1
1010
1011
E3
3
0001
0011
0100
0101
0110
0111
1000
16T1 X 4
1100
1101
1110
1111
T3
8T1
E1
3T1
26 MHz
13 MHz
153.6 MHz
76.8 MHz
20 MHz
10 MHz
38.4 MHz
5 MHz
61.44 MHz 4
2T1
30.72 MHz 4
15.36 MHz 4
2T1
E1
52 MHz
4T1
4T1
2E1
6.48 MHz
E3
T1
7.68 MHz 4
3.84 MHz 4
T1
Output is disabled (output high).
Note:
1. n = 1 or 2. Each output is assigned a frequency divider.
2. In the APLL, the selected T0/T4 DPLL output may be multiplied. E1 = 2.048 MHz, T1 = 1.544 MHz, E3 = 34.368 MHz, T3 = 44.736 MHz. The blank cell means the configuration is
reserved.
3. The 622.08 MHz and 311.04 MHz differential signals are only output on OUT1.
4. The 61.44 MHz, 30.72 MHz, 15.36 MHz, 7.68 MHz and 3.84 MHz outputs are only derived from T0 APLL.
Functional Description
37
December 3, 2008
IDT82V3255
3.13.2
WAN PLL
limit, whether the selected frame sync input signal is enabled to synchronize the frame sync output signal is determined by the SYNC_BYPASS
bit, the AUTO_EXT_SYNC_EN bit and the EXT_SYNC_EN bit. Refer to
Table 28 for details.
FRAME SYNC OUTPUT SIGNALS
An 8 kHz and a 2 kHz frame sync signals are output on the
FRSYNC_8K and MFRSYNC_2K pins if enabled by the 8K_EN and
2K_EN bits respectively. They are CMOS outputs.
When the selected frame sync input signal is enabled to synchronize
the frame sync output signal, it should be adjusted to align itself with the
T0 selected input clock. Nominally, the falling edge of the selected frame
sync input signal is aligned with the rising edge of the T0 selected input
clock. The selected frame sync input signal may be 0.5 UI early/late or 1
UI late due to the circuit and board wiring delays. Setting the sampling of
the selected frame sync input signal by the SYNC_PHn[1:0] bits (n = 1,
2 or 3 corresponding to EX_SYNC1, EX_SYNC2 or EX_SYCN3 respectively) will compensate this early/late. Refer to Figure 8 to Figure 11.
The two frame sync signals are derived from the T0 APLL output and
are aligned with the output clock. They can be synchronized to one of
the three frame sync input signals.
One of the three frame sync input signals is selected, as determined
by the SYNC_BYPASS bit and the T0 selected input clock, as shown in
Table 27:
Table 27: Frame Sync Input Signal Selection
SYNC_BYPASS T0 Selected Input Clock
0
Selected Frame Sync Input
Signal
don’t-care
IN1_CMOS or IN1_DIFF
IN2_CMOS or IN2_DIFF
IN3_CMOS
none
1
The EX_SYNC_ALARM_MON bit indicates whether the selected
frame sync input signal is in external sync alarm status. The external
sync alarm is indicated by the EX_SYNC_ALARM 1 bit. If the
EX_SYNC_ALARM 2 bit is ‘1’, the occurrence of the external sync alarm
will trigger an interrupt.
EX_SYNC1
EX_SYNC1
EX_SYNC2
EX_SYNC3
none
The 8 kHz and the 2 kHz frame sync output signals can be inverted
by setting the 8K_INV and 2K_INV bits respectively. The frame sync outputs can be 50:50 duty cycle or pulsed, as determined by the 8K_PUL
and 2K_PUL bits respectively. When they are pulsed, the pulse width is
defined by the period of OUT2; and they are pulsed on the position of
the falling or rising edge of the standard 50:50 duty cycle, as selected by
the 2K_8K_PUL_POSITION bit.
If the selected frame sync input signal with respect to the T0 selected
input clock is above a limit set by the SYNC_MON_LIMT[2:0] bits, an
external sync alarm will be raised and the selected frame sync input signal is disabled to synchronize the frame sync output signals. The external sync alarm is cleared once the selected frame sync input signal with
respect to the T0 selected input clock is within the limit. If it is within the
Table 28: Synchronization Control
SYNC_BYPASS
AUTO_EXT_SYNC_EN
EXT_SYNC_EN
Synchronization
0
don’t-care
0
1
0
1
1
Disabled
Enabled
Disabled
Enabled
1
don’t-care
T0 selected
input clock
T0 selected
input clock
Selected frame
sync input signal
Selected frame
sync input signal
Frame sync
output signals
Frame sync
output signals
Output clocks
Output clocks
Figure 8. On Target Frame Sync Input Signal Timing
Functional Description
Figure 9. 0.5 UI Early Frame Sync Input Signal Timing
38
December 3, 2008
IDT82V3255
WAN PLL
T0 selected
input clock
T0 selected
input clock
Selected frame
sync input signal
Selected frame
sync input signal
Frame sync
output signals
Frame sync
output signals
Output clocks
Output clocks
Figure 10. 0.5 UI Late Frame Sync Input Signal Timing
Figure 11. 1 UI Late Frame Sync Input Signal Timing
Table 29: Related Bit / Register in Chapter 3.13
Bit
Register
Address (Hex)
OUT1_PECL_LVDS
OUTn_PATH_SEL[3:0] (n = 1 or 2)
OUTn_DIVIDER[3:0] (n = 1 or 2)
IN_SONET_SDH
AUTO_EXT_SYNC_EN
EXT_SYNC_EN
OUTn_INV (n = 1 or 2)
8K_EN
2K_EN
8K_INV
2K_INV
8K_PUL
2K_PUL
2K_8K_PUL_POSITION
SYNC_BYPASS
SYNC_MON_LIMT[2:0]
DIFFERENTIAL_IN_OUT_OSCI_CNFG
0A
OUT1_FREQ_CNFG, OUT2_FREQ_CNFG
71, 6D
INPUT_MODE_CNFG
09
OUT1_INV_CNFG, OUT2_INV_CNFG
73, 72
FR_MFR_SYNC_CNFG
74
SYNC_MONITOR_CNFG
7C
EX_SYNC_ALARM_MON
SYNC_PHASE_CNFG
OPERATING_STS
7D
52
EX_SYNC_ALARM 1
INTERRUPTS3_STS
0F
EX_SYNC_ALARM 2
INTERRUPTS3_ENABLE_CNFG
12
SYNC_PHn[1:0] (n = 1, 2 or 3)
Functional Description
39
December 3, 2008
IDT82V3255
3.14
WAN PLL
INTERRUPT SUMMARY
3.15
The interrupt sources of the device are as follows:
• T4 DPLL locking status change
• Input clocks for T0 path validity change
• T0 selected input clock fail
• Input clocks for T4 path change to be no qualified input clock
available
• T0 DPLL operating mode switch
• External sync alarm
The main features supported by the T0 path are as follows:
• Phase lock alarm;
• Forced or Automatic input clock selection/switch;
• 3 primary and 3 secondary, temporary DPLL operating modes,
switched automatically or under external control;
• Automatic switch between starting, acquisition and locked bandwidths/damping factors;
• Programmable DPLL bandwidths from 0.1 Hz to 560 Hz in 11
steps;
• Programmable damping factors: 1.2, 2.5, 5, 10 and 20;
• Fast loss, coarse phase loss, fine phase loss and hard limit
exceeding monitoring;
• Output phase and frequency offset limited;
• Automatic Instantaneous, Automatic Slow Averaged, Automatic
Fast Averaged or Manual holdover frequency offset acquiring;
• PBO to minimize output phase transients;
• Programmable output phase offset;
• Low jitter multiple clock outputs with programmable polarity;
• Low jitter 2 kHz and 8 kHz frame sync signal outputs with programmable pulse width and polarity;
All of the above interrupt events are indicated by the corresponding
interrupt status bit. If the corresponding interrupt enable bit is set, any of
the interrupts can be reported by the INT_REQ pin. The output characteristics on the INT_REQ pin are determined by the HZ_EN bit and the
INT_POL bit.
Interrupt events are cleared by writing a ‘1’ to the corresponding
interrupt status bit. The INT_REQ pin will be inactive only when all the
pending enabled interrupts are cleared.
In addition, the interrupt of T0 selected input clock fail can be
reported by the TDO pin, as determined by the LOS_FLAG_TO_TDO
bit.
The main features supported by the T4 path are as follows:
• Forced or Automatic input clock selection/switch;
• Locking to T0 DPLL output;
• 3 DPLL operating modes, switched automatically or under external control;
• Programmable DPLL bandwidth: 18 Hz, 35 Hz, 70 Hz and 560
Hz;
• Programmable damping factor: 1.2, 2.5, 5, 10 and 20;
• Fast loss, coarse phase loss, fine phase loss and hard limit
exceeding monitoring;
• Output phase and frequency offset limited;
• Automatic Instantaneous holdover frequency offset;
• Low jitter multiple clock outputs with programmable polarity.
Table 30: Related Bit / Register in Chapter 3.14
Bit
HZ_EN
INT_POL
LOS_FLAG_TO_TDO
Functional Description
Register
Address (Hex)
INTERRUPT_CNFG
0C
MON_SW_PBO_CNFG
0B
T0 AND T4 SUMMARY
40
December 3, 2008
IDT82V3255
3.16
WAN PLL
POWER SUPPLY FILTERING TECHNIQUES
3. 3V
IDT 82 V3255
SLF7028T-100M1R1
VDDA
0.1 µ F
0.1 µF
0.1 µF
4, 14, 57
0.1 µF
1, 3, 15, 58
10 µF
7, 10, 11, 31, 40, 53
VDD _DIFF
22
21
AGND
DGND
GND_DIFF
3.3V
SLF7028T-100M1R1
10 µF
VDDD
0.1 µF
0.1 µF
0.1 µF
0.1 µF
0.1 µF
0.1 µ F
0.1 µF
0 .1 µF
0.1 µF
8, 9, 12, 32, 36, 38, 39, 45, 46 , 54
0.1 µF
Figure 12. IDT82V3255 Power Decoupling Scheme
The analog power supply VDDA and VDD_DIFF should have low
impedance. This can be achieved by using one 10 uF (1210 case size,
ceramic) and at least four 0.1 uF (0402 case size, ceramic) capacitors in
parallel. The 0.1 uF (0402 case size, ceramic) capacitors must be
placed right next to the VDDA and VDD_DIFF pins as close as possible.
Note that the 10 uF capacitor must be of 1210 case size, and it must be
ceramic for lowest ESR (Effective Series Resistance) possible. The 0.1
uF should be of case size 0402, this offers the lowest ESL (Effective
Series Inductance) to achieve low impedance towards the high speed
range.
To achieve optimum jitter performance, power supply filtering is
required to minimize supply noise modulation of the output clocks. The
common sources of power supply noise are switch power supplies and
the high switching noise from the outputs to the internal PLL. The
82V3255 provides separate VDDA power pins for the internal analog
PLL, VDD_DIFF for the differential output driver circuit and VDDD pins
for the core logic as well as I/O driver circuits.
To minimize switching power supply noise generated by the switching regulator, the power supply output should be filtering with sufficient
bulk capacity to minimize ripple and 0.1 uF (0402 case size, ceramic)
caps to filter out the switching transients.
For VDDD, at least ten 0.1 uF (0402 case size, ceramic) and one 10
uF (1210 case size, ceramic) capacitors are recommended. The 0.1 uF
capacitors should be placed as close to the VDDD pins as possible.
For the 82V3255, the decoupling for VDDA, VDD_DIFF and VDDD
are handled individually. VDDD, VDD_DIFF and VDDA should be individually connected to the power supply plane through vias, and bypass
capacitors should be used for each pin. Figure 12 illustrated how bypass
capacitor and ferrite bead should be connected to power pins.
Functional Description
Please refer to evaluation board schematic for details.
41
December 3, 2008
IDT82V3255
3.17
WAN PLL
LINE CARD APPLICATION
Master Clock
Board
OC-N
Clock
Clock
Sync
Slave Clock
Board
Clock
Sync
IDT82V3255
Clock
Sync
Sync
SDH/SONET
System
Chip
e.g.
Transciever
TSE
......
Optical signal
155 M, 622 M, 2.5 G,
or 10 Gbit/s
OC-n Line Card Board
Standby Clock
Board
Backplane
Figure 13. Line Card Application
Functional Description
42
December 3, 2008
IDT82V3255
4
WAN PLL
MICROPROCESSOR INTERFACE
ing edge of SCLK. When CLKE is asserted high, data on SDO will be
clocked out on the falling edge of SCLK.
The microprocessor interface provides access to read and write the
registers in the device. The microprocessor interface supports Serial
mode only.
In a write operation, data on SDI will be clocked in on the rising edge
of SCLK.
In a read operation, the active edge of SCLK is selected by CLKE.
When CLKE is asserted low, data on SDO will be clocked out on the ris-
CS
SCLK
tsu1
SDI
th2
tpw2
tsu2
th1
tpw1
R/W
A0
A1
A2
A3
A4
A5
A6
td1
High-Z
SDO
D0
td2
D1
D2
D3
D4
D5
D6
D7
Figure 14. Serial Read Timing Diagram (CLKE Asserted Low)
CS
th2
SCLK
SDI
R/W
A0
A1
A2
A3
A4
A5
A6
td1
High-Z
td2
D0
SDO
D1
D2
D3
D4
D5
D6
D7
Figure 15. Serial Read Timing Diagram (CLKE Asserted High)
Microprocessor Interface
43
December 3, 2008
IDT82V3255
WAN PLL
Table 31: Read Timing Characteristics in Serial Mode
Symbol
Parameter
Min
Typ
Max
Unit
T
One cycle time of the master clock
12.86
ns
tin
Delay of input pad
5
ns
tout
Delay of output pad
5
ns
tsu1
Valid SDI to valid SCLK setup time
4
ns
tsu2
Valid CS to valid SCLK setup time
14
ns
td1
Valid SCLK to valid data delay time
10
ns
td2
CS rising edge to SDO high impedance delay time
10
ns
tpw1
SCLK pulse width low
3.5T + 5
ns
tpw2
SCLK pulse width high
3.5T + 5
ns
th1
Valid SDI after valid SCLK hold time
6
ns
th2
Valid CS after valid SCLK hold time (CLKE = 0/1)
5
ns
tTI
Time between consecutive Read-Read or Read-Write accesses
(CS rising edge to CS falling edge)
10
ns
CS
tsu2
SCLK
th1
tpw1
tsu1
SDI
th2
tpw2
R/W
A0
A1
A2
A3
A4
A5
A6
D0
D1
D2
D3
D4
D5
D6
D7
High-Z
SDO
Figure 16. Serial Write Timing Diagram
Table 32: Write Timing Characteristics in Serial Mode
Symbol
Parameter
Min
Typ
Max
Unit
T
One cycle time of the master clock
12.86
ns
tin
Delay of input pad
5
ns
tout
Delay of output pad
5
ns
tsu1
Valid SDI to valid SCLK setup time
4
ns
tsu2
Valid CS to valid SCLK setup time
14
ns
tpw1
SCLK pulse width low
3.5T
ns
tpw2
SCLK pulse width high
3.5T
ns
th1
Valid SDI after valid SCLK hold time
6
ns
th2
Valid CS after valid SCLK hold time
5
ns
tTI
Time between consecutive Write-Write or Write-Read accesses
(CS rising edge to CS falling edge)
10
ns
Microprocessor Interface
44
December 3, 2008
IDT82V3255
5
WAN PLL
JTAG
This device is compliant with the IEEE 1149.1 Boundary Scan standard except the following:
• The output boundary scan cells do not capture data from the
core and the device does not support EXTEST instruction;
• The TRST pin is set low by default and JTAG is disabled in order
to be consistent with other manufacturers.
The JTAG interface timing diagram is shown in Figure 17.
tTCK
TCK
tS
tH
TMS
TDI
tD
TDO
Figure 17. JTAG Interface Timing Diagram
Table 33: JTAG Timing Characteristics
Symbol
JTAG
Parameter
Min
tTCK
Typ
Max
TCK period
100
ns
tS
TMS / TDI to TCK setup time
25
ns
tH
TCK to TMS / TDI Hold Time
25
ns
tD
TCK to TDO delay time
50
45
Unit
ns
December 3, 2008
IDT82V3255
6
WAN PLL
PROGRAMMING INFORMATION
The access of the Multi-word Registers is different from that of the
Single-word Registers. Take the registers (04H, 05H and 06H) for an
example, the write operation for the Multi-word Registers follows a fixed
sequence. The register (04H) is configured first and the register (06H) is
configured last. The three registers are configured continuously and
should not be interrupted by any operation. The crystal calibration configuration will take effect after all the three registers are configured. During read operation, the register (04H) is read first and the register (06H)
is read last. The crystal calibration reading should be continuous and not
be interrupted by any operation.
After reset, all the registers are set to their default values. The registers are read or written via the microprocessor interface.
Before any write operation, the value in register
PROTECTION_CNFG is recommended to be confirmed to make sure
whether the write operation is enabled. The device provides 3 register
protection modes:
• Protected mode: no other registers can be written except register
PROTECTION_CNFG itself;
• Fully Unprotected mode: all the writable registers can be written;
• Single Unprotected mode: one more register can be written
besides register PROTECTION_CNFG. After write operation
(not including writing a ‘1’ to clear a bit to ‘0’), the device automatically switches to Protected mode.
Certain bit locations within the device register map are designated as
Reserved. To ensure proper and predictable operation, bits designated
as Reserved should not be written by the users. In addition, their value
should be masked out from any testing or error detection methods that
are implemented.
Writing ‘0’ to the registers will take no effect if the registers are
cleared by writing ‘1’.
6.1
T0 and T4 paths share some registers, whose addresses are 27H,
28H, 2AH, 4EH, 4FH, 5AH, 5BH, 62H ~ 64H, 68H and 69H. The names
of shared registers are marked with a *. Before register read/write operation, register T4_T0_REG_SEL_CNFG is recommended to be confirmed to make sure whether the register operation is available for T0 or
T4 path.
REGISTER MAP
Table 34 is the map of all the registers, sorted in an ascending order
of their addresses.
Table 34: Register List and Map
Address
(Hex)
Register Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reference
Page
Global Control Registers
00
01
04
05
06
07
08
09
0A
ID[7:0] - Device ID 1
ID[15:8] - Device ID 2
NOMINAL_FREQ[7:0]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 1
NOMINAL_FREQ[15:8]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 2
NOMINAL_FREQ[23:16]_CNFG
Crystal Oscillator Frequency Offset
Calibration Configuration 3
T4_T0_REG_SEL_CNFG - T0 / T4
Registers Selection Configuration
PHASE_ALARM_TIME_OUT_CNFG Phase Lock Alarm Time-Out Configuration
-
-
ID[7:0]
ID[15:8]
P 51
P 51
NOMINAL_FREQ_VALUE[7:0]
P 52
NOMINAL_FREQ_VALUE[15:8]
P 52
NOMINAL_FREQ_VALUE[23:16]
P 52
-
MULTI_FACTOR[1:0]
-
-
-
-
TIME_OUT_VALUE[5:0]
AUTO_EX
PH_ALAR
INPUT_MODE_CNFG - Input Mode
EXT_SYN
T_SYNC_
M_TIMEO
Configuration
C_EN
EN
UT
DIFFERENTIAL_IN_OUT_OSCI_CNF
G - Differential Input / Output Port &
Master Clock Configuration
Programming Information
T4_T0_SE
L
46
SYNC_FREQ[1:0]
-
-
IN_SONET
_SDH
P 53
P 53
-
OSC_EDG OUT1_PE
E
CL_LVDS
REVERTIV
E_MODE
P 54
-
P 55
December 3, 2008
IDT82V3255
WAN PLL
Table 34: Register List and Map (Continued)
Address
(Hex)
0B
7E
0C
0D
0E
0F
10
11
12
16
17
18
19
1A
1D
23
24
25
27
28
Register Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
MON_SW_PBO_CNFG - Frequency
LOS_FLA
FREQ_MO
FREQ_MO
ULTR_FAS
PBO_FRE
Monitor, Input Clock Selection & PBO
G_TO_TD
EXT_SW
PBO_EN
N_HARD_
N_CLK
T_SW
Z
Control
O
EN
PROTECTION_CNFG - Register ProPROTECTION_DATA[7:0]
tection Mode Configuration
Interrupt Registers
INTERRUPT_CNFG - Interrupt ConfigHZ_EN
INT_POL
uration
INTERRUPTS1_STS - Interrupt Status
IN2_DIFF IN1_DIFF IN2_CMOS IN1_CMOS
1
T0_OPER T0_MAIN_
INTERRUPTS2_STS - Interrupt Status
ATING_MO REF_FAIL
IN3_CMOS
2
DE
ED
INTERRUPTS3_STS - Interrupt Status EX_SYNC
INPUT_TO
T4_STS
3
_ALARM
_T4
INTERRUPTS1_ENABLE_CNFG
IN2_DIFF IN1_DIFF IN2_CMOS IN1_CMOS
Interrupt Control 1
T0_OPER T0_MAIN_
INTERRUPTS2_ENABLE_CNFG
ATING_MO REF_FAIL
IN3_CMOS
Interrupt Control 2
DE
ED
INTERRUPTS3_ENABLE_CNFG
- EX_SYNC
INPUT_TO
T4_STS
Interrupt Control 3
_ALARM
_T4
Input Clock Frequency & Priority Configuration Registers
IN1_CMOS_CNFG - CMOS Input DIRECT_D
LOCK_8K
BUCKET_SEL[1:0]
IN_FREQ[3:0]
Clock 1 Configuration
IV
IN2_CMOS_CNFG - CMOS Input DIRECT_D
LOCK_8K
BUCKET_SEL[1:0]
IN_FREQ[3:0]
Clock 2 Configuration
IV
IN1_IN2_DIFF_HF_DIV_CNFG - Differential Input Clock 1 & 2 High Fre- IN2_DIFF_DIV[1:0]
IN1_DIFF_DIV[1:0]
quency Divider Configuration
IN1_DIFF_CNFG - Differential Input DIRECT_D
LOCK_8K
BUCKET_SEL[1:0]
IN_FREQ[3:0]
Clock 1 Configuration
IV
IN2_DIFF_CNFG - Differential Input DIRECT_D
LOCK_8K
BUCKET_SEL[1:0]
IN_FREQ[3:0]
Clock 2 Configuration
IV
IN3_CMOS_CNFG - CMOS Input DIRECT_D
LOCK_8K
BUCKET_SEL[1:0]
IN_FREQ[3:0]
Clock 3 Configuration
IV
PRE_DIV_CH_CNFG - DivN Divider
PRE_DIV_CH_VALUE[3:0]
Channel Selection
PRE_DIVN[7:0]_CNFG - DivN Divider
PRE_DIVN_VALUE[7:0]
Division Factor Configuration 1
PRE_DIVN[14:8]_CNFG
DivN
PRE_DIVN_VALUE[14:8]
Divider Division Factor Configuration 2
IN1_IN2_CMOS_SEL_PRIORITY_CN
FG - CMOS Input Clock 1 & 2 Priority
IN2_CMOS_SEL_PRIORITY[3:0]
IN1_CMOS_SEL_PRIORITY[3:0]
Configuration *
IN1_IN2_DIFF_SEL_PRIORITY_CNF
G - Differential Input Clock 1 & 2 PriorIN2_DIFF_SEL_PRIORITY[3:0]
IN1_DIFF_SEL_PRIORITY[3:0]
ity Configuration *
Programming Information
47
Reference
Page
P 56
P 57
P 58
P 58
P 59
P 60
P 60
P 61
P 61
P 62
P 63
P 64
P 65
P 66
P 67
P 68
P 68
P 69
P 70
P 71
December 3, 2008
IDT82V3255
WAN PLL
Table 34: Register List and Map (Continued)
Address
(Hex)
2A
2E
2F
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
Register Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
IN3_CMOS_SEL_PRIORITY_CNFG CMOS Input Clock 3 Priority ConfiguIN3_CMOS_SEL_PRIORITY[3:0]
ration *
Input Clock Quality Monitoring Configuration & Status Registers
FREQ_MON_FACTOR_CNFG - FacFREQ_MON_FACTOR[3:0]
tor of Frequency Monitor Configuration
ALL_FREQ_MON_THRESHOLD_CN
FG - Frequency Monitor Threshold for
ALL_FREQ_HARD_THRESHOLD[3:0]
All Input Clocks Configuration
UPPER_THRESHOLD_0_CNFG
Upper Threshold for Leaky Bucket
UPPER_THRESHOLD_0_DATA[7:0]
Configuration 0
LOWER_THRESHOLD_0_CNFG
Lower Threshold for Leaky Bucket
LOWER_THRESHOLD_0_DATA[7:0]
Configuration 0
BUCKET_SIZE_0_CNFG - Bucket
BUCKET_SIZE_0_DATA[7:0]
Size for Leaky Bucket Configuration 0
DECAY_RATE_0_CNFG - Decay Rate
DECAY_RATE_0_DATA
for Leaky Bucket Configuration 0
[1:0]
UPPER_THRESHOLD_1_CNFG
Upper Threshold for Leaky Bucket
UPPER_THRESHOLD_1_DATA[7:0]
Configuration 1
LOWER_THRESHOLD_1_CNFG
Lower Threshold for Leaky Bucket
LOWER_THRESHOLD_1_DATA[7:0]
Configuration 1
BUCKET_SIZE_1_CNFG - Bucket
BUCKET_SIZE_1_DATA[7:0]
Size for Leaky Bucket Configuration 1
DECAY_RATE_1_CNFG - Decay Rate
DECAY_RATE_1_DATA
for Leaky Bucket Configuration 1
[1:0]
UPPER_THRESHOLD_2_CNFG
Upper Threshold for Leaky Bucket
UPPER_THRESHOLD_2_DATA[7:0]
Configuration 2
LOWER_THRESHOLD_2_CNFG
Lower Threshold for Leaky Bucket
LOWER_THRESHOLD_2_DATA[7:0]
Configuration 2
BUCKET_SIZE_2_CNFG - Bucket
BUCKET_SIZE_2_DATA[7:0]
Size for Leaky Bucket Configuration 2
DECAY_RATE_2_DATA
DECAY_RATE_2_CNFG - Decay Rate
[1:0]
for Leaky Bucket Configuration 2
UPPER_THRESHOLD_3_CNFG
Upper Threshold for Leaky Bucket
UPPER_THRESHOLD_3_DATA[7:0]
Configuration 3
LOWER_THRESHOLD_3_CNFG
Lower Threshold for Leaky Bucket
LOWER_THRESHOLD_3_DATA[7:0]
Configuration 3
BUCKET_SIZE_3_CNFG - Bucket
BUCKET_SIZE_3_DATA[7:0]
Size for Leaky Bucket Configuration 3
DECAY_RATE_3_CNFG - Decay Rate
DECAY_RATE_3_DATA
[1:0]
for Leaky Bucket Configuration 3
Programming Information
48
Reference
Page
P 72
P 73
P 73
P 74
P 74
P 74
P 75
P 75
P 75
P 76
P 76
P 76
P 77
P 77
P 77
P 78
P 78
P 78
P 79
December 3, 2008
IDT82V3255
WAN PLL
Table 34: Register List and Map (Continued)
Address
(Hex)
41
42
Register Name
IN_FREQ_READ_CH_CNFG - Input
Clock Frequency Read Channel
Selection
IN_FREQ_READ_STS - Input Clock
Frequency Read Value
Bit 7
Bit 6
Bit 5
Bit 4
-
-
-
-
44
-
45
IN1_IN2_DIFF_STS - Differential Input
Clock 1 & 2 Status
-
47
IN3_CMOS_STS - CMOS Input Clock
3 Status
-
4B
4E
4F
50
51
52
53
54
55
56
57
58
Bit 2
Bit 1
Bit 0
IN_FREQ_READ_CH[3:0]
IN2_CMOS
_FREQ_H
ARD_ALA
RM
IN2_DIFF_
FREQ_HA
RD_ALAR
M
IN2_CMOS
_NO_ACTI
VITY_ALA
RM
IN2_DIFF_
NO_ACTIV
ITY_ALAR
M
-
-
IN2_CMOS
_PH_LOC
K_ALARM
-
IN2_DIFF_
PH_LOCK
_ALARM
-
-
-
P 80
IN1_CMOS
_FREQ_H
ARD_ALA
RM
IN1_DIFF_
FREQ_HA
RD_ALAR
M
IN3_CMOS
_FREQ_H
ARD_ALA
RM
IN1_CMOS
_NO_ACTI
VITY_ALA
RM
IN1_DIFF_
NO_ACTIV
ITY_ALAR
M
IN3_CMOS
_NO_ACTI
VITY_ALA
RM
IN1_CMOS
_PH_LOC
K_ALARM
P 81
IN1_DIFF_
PH_LOCK
_ALARM
P 82
IN3_CMOS
_PH_LOC
K_ALARM
P 83
T0 / T4 DPLL Input Clock Selection Registers
INPUT_VALID1_STS - Input Clocks
IN2_DIFF IN1_DIFF IN2_CMOS IN1_CMOS
Validity 1
INPUT_VALID2_STS - Input Clocks
IN3_CMOS
Validity 2
PRIORITY_TABLE1_STS - Priority
HIGHEST_PRIORITY_VALIDATED[3:0]
CURRENTLY_SELECTED_INPUT[3:0]
Status 1 *
PRIORITY_TABLE2_STS - Priority
SECOND_HIGHEST_PRIORITY_VALIDATED[3:0
THIRD_HIGHEST_PRIORITY_VALIDATED[3:0]
Status 2 *
]
T0_INPUT_SEL_CNFG - T0 Selected
T0_INPUT_SEL[3:0]
Input Clock Configuration
T4_LOCK_ T0_FOR_T T4_TEST_
T4_INPUT_SEL_CNFG - T4 Selected
T4_INPUT_SEL[3:0]
T0
4
T0_PH
Input Clock Configuration
T0 / T4 DPLL State Machine Control Registers
EX_SYNC
T0_DPLL_ T4_DPLL_
OPERATING_STS - DPLL Operating
T4_DPLL_
T0_DPLL_
_ALARM_
T0_DPLL_OPERATING_MODE[2:0]
SOFT_FRE SOFT_FRE
Status
LOCK
LOCK
MON
Q_ALARM Q_ALRAM
T0_OPERATING_MODE_CNFG - T0
T0_OPERATING_MODE[2:0]
DPLL Operating Mode Configuration
T4_OPERATING_MODE_CNFG - T4
T4_OPERATING_MODE[2:0]
DPLL Operating Mode Configuration
T0 / T4 DPLL & APLL Configuration Registers
T0_DPLL_APLL_PATH_CNFG - T0
T0_GSM_OBSAI_16E1 T0_12E1_24T1_E3_T3
T0_APLL_PATH[3:0]
DPLL & APLL Path Configuration
_16T1_SEL[1:0]
_SEL[1:0]
T0_DPLL_START_BW_DAMPING_C
NFG - T0 DPLL Start Bandwidth & T0_DPLL_START_DAMPING[2:0]
T0_DPLL_START_BW[4:0]
Damping Factor Configuration
T0_DPLL_ACQ_BW_DAMPING_CNF
G - T0 DPLL Acquisition Bandwidth & T0_DPLL_ACQ_DAMPING[2:0]
T0_DPLL_ACQ_BW[4:0]
Damping Factor Configuration
T0_DPLL_LOCKED_BW_DAMPING_
CNFG - T0 DPLL Locked Bandwidth & T0_DPLL_LOCKED_DAMPING[2:0]
T0_DPLL_LOCKED_BW[4:0]
Damping Factor Configuration
Programming Information
49
Reference
Page
P 79
IN_FREQ_VALUE[7:0]
IN1_IN2_CMOS_STS - CMOS Input
Clock 1 & 2 Status
4A
Bit 3
P 84
P 84
P 85
P 86
P 86
P 87
P 88
P 89
P 89
P 90
P 91
P 92
P 93
December 3, 2008
IDT82V3255
WAN PLL
Table 34: Register List and Map (Continued)
Address
(Hex)
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
Register Name
T0_BW_OVERSHOOT_CNFG - T0
DPLL Bandwidth Overshoot Configuration
PHASE_LOSS_COARSE_LIMIT_CNF
G - Phase Loss Coarse Detector Limit
Configuration *
PHASE_LOSS_FINE_LIMIT_CNFG Phase Loss Fine Detector Limit Configuration *
T0_HOLDOVER_MODE_CNFG - T0
DPLL Holdover Mode Configuration
T0_HOLDOVER_FREQ[7:0]_CNFG T0 DPLL Holdover Frequency Configuration 1
T0_HOLDOVER_FREQ[15:8]_CNFG
- T0 DPLL Holdover Frequency Configuration 2
T0_HOLDOVER_FREQ[23:16]_CNFG
- T0 DPLL Holdover Frequency Configuration 3
T4_DPLL_APLL_PATH_CNFG - T4
DPLL & APLL Path Configuration
T4_DPLL_LOCKED_BW_DAMPING_
CNFG - T4 DPLL Locked Bandwidth &
Damping Factor Configuration
CURRENT_DPLL_FREQ[7:0]_STS DPLL Current Frequency Status 1 *
CURRENT_DPLL_FREQ[15:8]_STS DPLL Current Frequency Status 2 *
CURRENT_DPLL_FREQ[23:16]_STS
- DPLL Current Frequency Status 3 *
DPLL_FREQ_SOFT_LIMIT_CNFG DPLL Soft Limit Configuration
DPLL_FREQ_HARD_LIMIT[7:0]_CNF
G - DPLL Hard Limit Configuration 1
DPLL_FREQ_HARD_LIMIT[15:8]_CN
FG - DPLL Hard Limit Configuration 2
CURRENT_DPLL_PHASE[7:0]_STS DPLL Current Phase Status 1 *
CURRENT_DPLL_PHASE[15:8]_STS
- DPLL Current Phase Status 2 *
T0_T4_APLL_BW_CNFG - T0 / T4
APLL Bandwidth Configuration
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reference
Page
AUTO_BW
_SEL
-
-
-
T0_LIMT
-
-
-
P 93
COARSE_
MULTI_PH
MULTI_PH
PH_LOS_L WIDE_EN
_8K_4K_2
PH_LOS_COARSE_LIMT[3:0]
_APP
IMT_EN
K_EN
FINE_PH_
FAST_LOS
LOS_LIMT
PH_LOS_FINE_LIMT[2:0]
_SW
_EN
MAN_HOL AUTO_AV
READ_AV TEMP_HOLDOVER_M
FAST_AVG
DOVER
G
G
ODE[1:0]
P 96
P 96
T0_HOLDOVER_FREQ[15:8]
P 97
T0_HOLDOVER_FREQ[23:16]
P 97
T4_DPLL_LOCKED_DAMPING[2:0]
-
T4_GSM_GPS_16E1_1 T4_12E1_24T1_E3_T3
6T1_SEL[1:0]
_SEL[1:0]
P 98
T4_DPLL_LOCKED_B
W[1:0]
P 99
-
-
CURRENT_DPLL_FREQ[7:0]
P 99
CURRENT_DPLL_FREQ[15:8]
P 99
CURRENT_DPLL_FREQ[23:16]
P 100
FREQ_LIM
T_PH_LOS
DPLL_FREQ_SOFT_LIMT[6:0]
-
P 95
T0_HOLDOVER_FREQ[7:0]
T4_APLL_PATH[3:0]
-
P 94
P 100
DPLL_FREQ_HARD_LIMT[7:0]
P 100
DPLL_FREQ_HARD_LIMT[15:8]
P 101
CURRENT_PH_DATA[7:0]
P 101
CURRENT_PH_DATA[15:8]
P 101
T0_APLL_BW[1:0]
-
-
T4_APLL_BW[1:0]
P 102
Output Configuration Registers
6D
71
72
OUT2_FREQ_CNFG - Output Clock 2
Frequency Configuration
OUT1_FREQ_CNFG - Output Clock 1
Frequency Configuration
OUT1_INV_CNFG - Output Clock 1
Invert Configuration
Programming Information
-
OUT2_PATH_SEL[3:0]
OUT2_DIVIDER[3:0]
P 103
OUT1_PATH_SEL[3:0]
OUT1_DIVIDER[3:0]
P 104
-
-
50
-
-
-
OUT1_INV
-
P 104
December 3, 2008
IDT82V3255
WAN PLL
Table 34: Register List and Map (Continued)
Address
(Hex)
Register Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Reference
Page
Bit 0
OUT2_INV_CNFG - Output Clock 2
OUT2_INV
Invert Configuration
FR_MFR_SYNC_CNFG - Frame Sync
2K_8K_PU
IN_2K_4K_
& Multiframe Sync Output Configura8K_EN
2K_EN
L_POSITI 8K_INV
8K_PUL
2K_INV
2K_PUL
8K_INV
tion
ON
PBO & Phase Offset Control Registers
PHASE_MON_PBO_CNFG - Phase
IN_NOISE
PH_MON_ PH_MON_
Transient Monitor & PBO ConfiguraPH_TR_MON_LIMT[3:0]
_WINDOW
EN
PBO_EN
tion
PHASE_OFFSET[7:0]_CNFG - Phase
PH_OFFSET[7:0]
Offset Configuration 1
PHASE_OFFSET[9:8]_CNFG - Phase PH_OFFS
PH_OFFSET[9:8]
Offset Configuration 2
ET_EN
Synchronization Configuration Registers
SYNC_MONITOR_CNFG - Sync Mon- SYNC_BY
SYNC_MON_LIMT[2:0]
itor Configuration
PASS
SYNC_PHASE_CNFG - Sync Phase
SYNC_PH3[1:0]
SYNC_PH2[1:0]
SYNC_PH1[1:0]
Configuration
73
74
78
7A
7B
7C
7D
6.2
REGISTER DESCRIPTION
6.2.1
GLOBAL CONTROL REGISTERS
P 105
P 106
P 107
P 107
P 108
P 109
P 110
ID[7:0] - Device ID 1
Address: 00H
Type: Read
Default Value: 10001000
7
6
5
4
3
2
1
0
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
Bit
Name
7-0
ID[7:0]
Description
Refer to the description of the ID[15:8] bits (b7~0, 01H).
ID[15:8] - Device ID 2
Address: 01H
Type: Read
Default Value: 00010001
7
6
5
4
3
2
1
0
ID15
ID14
ID13
ID12
ID11
ID10
ID9
ID8
Bit
Name
7-0
ID[15:8]
Programming Information
Description
The value in the ID[15:0] bits are pre-set, representing the identification number for the IDT82V3255.
51
December 3, 2008
IDT82V3255
WAN PLL
NOMINAL_FREQ[7:0]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 1
Address: 04H
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
NOMINAL_FRE
Q_VALUE7
NOMINAL_FRE
Q_VALUE6
NOMINAL_FRE
Q_VALUE5
NOMINAL_FRE
Q_VALUE4
NOMINAL_FRE
Q_VALUE3
NOMINAL_FRE
Q_VALUE2
NOMINAL_FRE
Q_VALUE1
NOMINAL_FRE
Q_VALUE0
Bit
7-0
Name
Description
NOMINAL_FREQ_VALUE[7:0] Refer to the description of the NOMINAL_FREQ_VALUE[23:16] bits (b7~0, 06H).
NOMINAL_FREQ[15:8]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 2
Address: 05H
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
NOMINAL_FRE
Q_VALUE15
NOMINAL_FRE
Q_VALUE14
NOMINAL_FRE
Q_VALUE13
NOMINAL_FRE
Q_VALUE12
NOMINAL_FRE
Q_VALUE11
NOMINAL_FRE
Q_VALUE10
NOMINAL_FRE
Q_VALUE9
NOMINAL_FRE
Q_VALUE8
Bit
7-0
Name
Description
NOMINAL_FREQ_VALUE[15:8] Refer to the description of the NOMINAL_FREQ_VALUE[23:16] bits (b7~0, 06H).
NOMINAL_FREQ[23:16]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 3
Address: 06H
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
NOMINAL_FRE
Q_VALUE23
NOMINAL_FRE
Q_VALUE22
NOMINAL_FRE
Q_VALUE21
NOMINAL_FRE
Q_VALUE20
NOMINAL_FRE
Q_VALUE19
NOMINAL_FRE
Q_VALUE18
NOMINAL_FRE
Q_VALUE17
NOMINAL_FRE
Q_VALUE16
Bit
7-0
Name
Description
The NOMINAL_FREQ_VALUE[23:0] bits represent a 2’s complement signed integer. If the value is multiplied by
0.0000884, the calibration value for the master clock in ppm will be gotten.
For example, the frequency offset on OSCI is +3 ppm. Though -3 ppm should be compensated, the calibration value is
NOMINAL_FREQ_VALUE[23:16] calculated as +3 ppm:
3 ÷ 0.0000884 = 33937 (Dec.) = 8490 (Hex);
So ‘008490’ should be written into these bits.
The calibration range is within ±741 ppm.
Programming Information
52
December 3, 2008
IDT82V3255
WAN PLL
T4_T0_REG_SEL_CNFG - T0 / T4 Registers Selection Configuration
Address: 07H
Type: Read / Write
Default Value: XXX0XXXX
7
6
5
4
3
2
1
0
-
-
-
T4_T0_SEL
-
-
-
-
Bit
Name
Description
7-5
-
4
T4_T0_SEL
3-0
-
Reserved.
A part of the registers are shared by T0 and T4 paths. These registers are addressed 27H, 28H, 2AH, 4EH, 4FH, 5AH, 5BH, 62H
~ 64H, 68H and 69H. This bit determines whether the register configuration is available for T0 or T4 path.
0: T0 path (default).
1: T4 path.
Reserved.
PHASE_ALARM_TIME_OUT_CNFG - Phase Lock Alarm Time-Out Configuration
Address: 08H
Type: Read / Write
Default Value: 00110010
7
6
5
4
3
2
1
0
MULTI_FACTO
R1
MULTI_FACTO
R0
TIME_OUT_VA
LUE5
TIME_OUT_VA
LUE4
TIME_OUT_VA
LUE3
TIME_OUT_VA
LUE2
TIME_OUT_VA
LUE1
TIME_OUT_VAL
UE0
Bit
7-6
5-0
Name
Description
These bits determine a factor which has a relationship with a period in seconds. A phase lock alarm will be raised if the T0
selected input clock is not locked in T0 DPLL within this period. If the PH_ALARM_TIMEOUT bit (b5, 09H) is ‘1’, the
phase lock alarm will be cleared after this period (starting from when the alarm is raised). Refer to the description of the
TIME_OUT_VALUE[5:0] bits (b5~0, 08H).
MULTI_FACTOR[1:0]
00: 2 (default)
01: 4
10: 8
11: 16
These bits represent an unsigned integer. If the value in these bits is multiplied by the value in the MULTI_FACTOR[1:0]
bits (b7~6, 08H), a period in seconds will be gotten.
TIME_OUT_VALUE[5:0] A phase lock alarm will be raised if the T0 selected input clock is not locked in T0 DPLL within this period. If the
PH_ALARM_TIMEOUT bit (b5, 09H) is ‘1’, the phase lock alarm will be cleared after this period (starting from when the
alarm is raised).
Programming Information
53
December 3, 2008
IDT82V3255
WAN PLL
INPUT_MODE_CNFG - Input Mode Configuration
Address: 09H
Type: Read / Write
Default Value: 10100X10
7
6
5
4
3
2
1
0
AUTO_EXT_SY
NC_EN
EXT_SYNC_EN
PH_ALARM_TI
MEOUT
SYNC_FREQ1
SYNC_FREQ0
IN_SONET_SD
H
-
REVERTIVE_M
ODE
Bit
Name
7
AUTO_EXT_SYNC_EN
6
EXT_SYNC_EN
5
4-3
2
1
0
Description
This bit is valid only when the SYNC_BYPASS bit (b7, 7CH) is ‘0’.
Refer to the description of the EXT_SYNC_EN bit (b6, 09H).
This bit is valid only when the SYNC_BYPASS bit (b7, 7CH) is ‘0’.
This bit, together with the AUTO_EXT_SYNC_EN bit (b7, 09H), determines whether the selected frame sync input signal is
enabled to synchronize the frame sync output signals.
AUTO_EXT_SYNC_EN
EXT_SYNC_EN
Synchronization
don’t-care
0
1
0
1
1
Disabled (default)
Enabled
Disabled
This bit determines how to clear the phase lock alarm.
0: The phase lock alarm will be cleared when a ‘1’ is written to the corresponding INn_CMOS_PH_LOCK_ALARM (n = 1, 2
PH_ALARM_TIMEOUT or 3) / INn_DIFF_PH_LOCK_ALARM (n = 1 or 2) bit (b4/0, 44H/45H/47H).
1: The phase lock alarm will be cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0]
(b7~6, 08H) in second) which starts from when the alarm is raised. (default)
These bits set the frequency of the frame sync signals input on the EX_SYNC1 ~ EX_SYNC3 pins.
00: 8 kHz (default)
SYNC_FREQ[1:0] 01: 8 kHz.
10: 4 kHz.
11: 2 kHz.
This bit selects the SDH or SONET network type.
0: SDH. The DPLL required clock is 2.048 MHz when the IN_FREQ[3:0] bits (b3~0, 16H, 17H, 19H, 1AH & 1DH) are ‘0001’
and the T0/T4 DPLL output from the 16E1/16T1 path is 16E1.
IN_SONET_SDH
1: SONET. The DPLL required clock is 1.544 MHz when the IN_FREQ[3:0] bits (b3~0, 16H, 17H, 19H, 1AH & 1DH) are
‘0001’ and the T0/T4 DPLL output from the 16E1/16T1 path is 16T1.
The default value of this bit is determined by the SONET/SDH pin during reset.
Reserved.
This bit selects Revertive or Non-Revertive switch for T0 path.
REVERTIVE_MODE 0: Non-Revertive switch. (default)
1: Revertive switch.
Programming Information
54
December 3, 2008
IDT82V3255
WAN PLL
DIFFERENTIAL_IN_OUT_OSCI_CNFG - Differential Input / Output Port & Master Clock Configuration
Address: 0AH
Type: Read / Write
Default Value: XXXXX00X
7
6
5
4
3
2
1
0
-
-
-
-
-
OSC_EDGE
OUT1_PECL_LVDS
-
Bit
Name
7-3
-
2
1
0
Description
Reserved.
This bit selects a better active edge of the master clock.
OSC_EDGE
0: The rising edge. (default)
1: The falling edge.
This bit selects a port technology for OUT1.
OUT1_PECL_LVDS 0: LVDS. (default)
1: PECL.
Reserved
Programming Information
55
December 3, 2008
IDT82V3255
WAN PLL
MON_SW_PBO_CNFG - Frequency Monitor, Input Clock Selection & PBO Control
Address: 0BH
Type: Read / Write
Default Value: 100X01X1
7
6
5
4
3
2
1
0
FREQ_MON_C
LK
LOS_FLAG_TO
_TDO
ULTR_FAST_SW
EXT_SW
PBO_FREZ
PBO_EN
-
FREQ_MON_H
ARD_EN
Bit
7
6
5
4
3
2
1
0
Name
Description
The bit selects a reference clock for input clock frequency monitoring.
0: The output of T0 DPLL.
1: The master clock. (default)
The bit determines whether the interrupt of T0 selected input clock fail - is reported by the TDO pin.
0: Not reported. TDO pin is used as JTAG test data output which complies with IEEE 1149.1. (default)
LOS_FLAG_TO_TDO
1: Reported. TDO pin mimics the state of the T0_MAIN_REF_FAILED bit (b6, 0EH) and does not strictly comply with IEEE
1149.1.
This bit determines whether the T0 selected input clock is valid when missing 2 consecutive clock cycles or more.
ULTR_FAST_SW
0: Valid. (default)
1: Invalid.
This bit determines the T0 input clock selection.
0: Forced selection or Automatic selection, as controlled by the T0_INPUT_SEL[3:0] bits (b3~0, 50H).
EXT_SW
1: External Fast selection.
The default value of this bit is determined by the FF_SRCSW pin during reset.
This bit is valid only when the PBO is enabled by the PBO_EN bit (b2, 0BH). It determines whether PBO is frozen at the current phase offset when a PBO event is triggered.
PBO_FREZ
0: Not frozen. (default)
1: Frozen. Further PBO events are ignored and the current phase offset is maintained.
This bit determines whether PBO is enabled when the T0 selected input clock switch or the T0 DPLL exiting from Holdover
mode or Free-Run mode occurs.
PBO_EN
0: Disabled.
1: Enabled. (default)
Reserved.
This bit determines whether the frequency hard alarm is enabled when the frequency of the input clock with respect to the
reference clock is above the frequency hard alarm threshold. The reference clock can be the output of T0 DPLL or the masFREQ_MON_HARD_EN ter clock, as determined by the FREQ_MON_CLK bit (b7, 0BH).
0: Disabled.
1: Enabled. (default)
FREQ_MON_CLK
Programming Information
56
December 3, 2008
IDT82V3255
WAN PLL
PROTECTION_CNFG - Register Protection Mode Configuration
Address: 7EH
Type: Read / Write
Default Value: 10000101
7
6
5
4
3
2
1
0
PROTECTION_
DATA7
PROTECTION_
DATA6
PROTECTION_
DATA5
PROTECTION_
DATA4
PROTECTION_
DATA3
PROTECTION_
DATA2
PROTECTION_
DATA1
PROTECTION_
DATA0
Bit
7-0
Name
Description
These bits select a register write protection mode.
00000000 - 10000100, 10000111 - 11111111: Protected mode. No other registers can be written except this register.
PROTECTION_DATA[7:0] 10000101: Fully Unprotected mode. All the writable registers can be written. (default)
10000110: Single Unprotected mode. One more register can be written besides this register. After write operation (not
including writing a ‘1’ to clear the bit to ‘0’), the device automatically switches to Protected mode.
Programming Information
57
December 3, 2008
IDT82V3255
6.2.2
WAN PLL
INTERRUPT REGISTERS
INTERRUPT_CNFG - Interrupt Configuration
Address: 0CH
Type: Read / Write
Default Value: XXXXXX10
7
6
5
4
3
2
1
0
-
-
-
-
-
-
HZ_EN
INT_POL
Bit
Name
Description
7-2
-
1
HZ_EN
0
INT_POL
Reserved.
This bit determines the output characteristics of the INT_REQ pin.
0: The output on the INT_REQ pin is high/low when the interrupt is active; the output is the opposite when the interrupt is inactive.
1: The output on the INT_REQ pin is high/low when the interrupt is active; the output is in high impedance state when the interrupt
is inactive. (default)
This bit determines the active level on the INT_REQ pin for an active interrupt indication.
0: Active low. (default)
1: Active high.
INTERRUPTS1_STS - Interrupt Status 1
Address: 0DH
Type: Read / Write
Default Value: XX1111XX
7
6
5
4
3
2
1
0
-
-
IN2_DIFF
IN1_DIFF
IN2_CMOS
IN1_CMOS
-
-
Bit
Name
Description
7-6
-
5-4
INn_DIFF
3-2
INn_CMOS
1-0
-
Reserved.
This bit indicates the validity changes (from ‘valid’ to ‘invalid’ or from ‘invalid’ to ‘valid’) for the corresponding INn_DIFF; i.e.,
whether there is a transition (from ‘0’ to ‘1’ or from ‘1’ to ‘0’) on the corresponding INn_DIFF bit (b5/4, 4AH). Here n is 2 or 1.
0: Has not changed.
1: Has changed. (default)
This bit is cleared by writing a ‘1’.
This bit indicates the validity changes (from ‘valid’ to ‘invalid’ or from ‘invalid’ to ‘valid’) for the corresponding INn_CMOS; i.e.,
whether there is a transition (from ‘0’ to ‘1’ or from ‘1’ to ‘0’) on the corresponding INn_CMOS bit (b3/2, 4AH). Here n is 2 or 1.
0: Has not changed.
1: Has changed. (default)
This bit is cleared by writing a ‘1’.
Reserved.
Programming Information
58
December 3, 2008
IDT82V3255
WAN PLL
INTERRUPTS2_STS - Interrupt Status 2
Address: 0EH
Type: Read / Write
Default Value: 00XXXXX1
7
6
5
4
3
2
1
0
T0_OPERATING
_MODE
T0_MAIN_REF_F
AILED
-
-
-
-
-
IN3_CMOS
Bit
7
6
5-1
0
Name
Description
This bit indicates the operating mode switch for T0 DPLL; i.e., whether the value in the
T0_DPLL_OPERATING_MODE[2:0] bits (b2~0, 52H) changes.
T0_OPERATING_MODE 0: Has not switched. (default)
1: Has switched.
This bit is cleared by writing a ‘1’.
This bit indicates whether the T0 selected input clock has failed. The T0 selected input clock fails when its validity
changes from ‘valid’ to ‘invalid’; i.e., when there is a transition from ‘1’ to ‘0’ on the corresponding INn_CMOS / INn_DIFF
bit (4AH, 4BH).
T0_MAIN_REF_FAILED
0: Has not failed. (default)
1: Has failed.
This bit is cleared by writing a ‘1’.
Reserved.
This bit indicates the validity changes (from ‘valid’ to ‘invalid’ or from ‘invalid’ to ‘valid’) for IN3_CMOS for T0 path, i.e.,
whether there is a transition (from ‘0’ to ‘1’ or from ‘1’ to ‘0’) on the corresponding IN3_CMOS bit (b0, 4BH).
IN3_CMOS
0: Has not changed.
1: Has changed. (default)
This bit is cleared by writing a ‘1’.
Programming Information
59
December 3, 2008
IDT82V3255
WAN PLL
INTERRUPTS3_STS - Interrupt Status 3
Address: 0FH
Type: Read / Write
Default Value: 11X1XXXX
7
6
5
4
3
2
1
0
EX_SYNC_ALARM
T4_STS
-
INPUT_TO_T4
-
-
-
-
Bit
Name
Description
This bit indicates whether an external sync alarm is raised; i.e., whether there is a transition from ‘0’ to ‘1’ on the
EX_SYNC_ALARM_MON bit (b7, 52H).
EX_SYNC_ALARM 0: Has not occurred.
1: Has occurred. (default)
This bit is cleared by writing a ‘1’.
This bit indicates the T4 DPLL locking status changes (from ‘locked’ to ‘unlocked’ or from ‘unlocked’ to ‘locked’); i.e., whether
there is a transition (from ‘0’ to ‘1’ or from ‘1’ to ‘0’) on the T4_DPLL_LOCK bit (b6, 52H).
T4_STS
0: Has not changed.
1: Has changed. (default)
This bit is cleared by writing a ‘1’.
Reserved.
This bit indicates whether all the input clocks for T4 path changes to be unqualified; i.e., whether the
HIGHEST_PRIORITY_VALIDATED[3:0] bits (b7~4, 4EH) are set to ‘0000’ when these bits are available for T4 path.
INPUT_TO_T4 0: Has not changed.
1: Has changed. (default)
This bit is cleared by writing a ‘1’.
Reserved.
7
6
5
4
3-0
INTERRUPTS1_ENABLE_CNFG - Interrupt Control 1
Address: 10H
Type: Read / Write
Default Value: XX0000XX
7
6
5
4
3
2
1
0
-
-
IN2_DIFF
IN1_DIFF
IN2_CMOS
IN1_CMOS
-
-
Bit
Name
Description
7-6
-
5-4
INn_DIFF
3-2
INn_CMOS
1-0
-
Reserved.
This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the input clock validity changes (from
‘valid’ to ‘invalid’ or from ‘invalid’ to ‘valid’), i.e., when the corresponding INn_DIFF bit (b5/4, 0DH) is ‘1’. Here n is 2 or 1.
0: Disabled. (default)
1: Enabled.
This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the input clock validity changes (from
‘valid’ to ‘invalid’ or from ‘invalid’ to ‘valid’), i.e., when the corresponding INn_CMOS bit (b3/2, 0DH) is ‘1’. Here n is 2 or 1.
0: Disabled. (default)
1: Enabled.
Reserved.
Programming Information
60
December 3, 2008
IDT82V3255
WAN PLL
INTERRUPTS2_ENABLE_CNFG - Interrupt Control 2
Address: 11H
Type: Read / Write
Default Value:00XXXXX0
7
6
5
4
3
2
1
0
T0_OPERATING
_MODE
T0_MAIN_REF_F
AILED
-
-
-
-
-
IN3_CMOS
Bit
Name
Description
This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the T0 DPLL operating mode
switches, i.e., when the T0_OPERATING_MODE bit (b7, 0EH) is ‘1’.
T0_OPERATING_MODE
0: Disabled. (default)
1: Enabled.
This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the T0 selected input clock
has failed; i.e., when the T0_MAIN_REF_FAILED bit (b6, 0EH) is ‘1’.
T0_MAIN_REF_FAILED
0: Disabled. (default)
1: Enabled.
Reserved.
This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the input clock validity
changes (from ‘valid’ to ‘invalid’ or from ‘invalid’ to ‘valid’), i.e., when the corresponding IN3_CMOS bit (b0, 0EH) is ‘1’.
IN3_CMOS
0: Disabled. (default)
1: Enabled.
7
6
5-1
0
INTERRUPTS3_ENABLE_CNFG - Interrupt Control 3
Address: 12H
Type: Read / Write
Default Value: 00X0XXXX
7
6
5
4
3
2
1
0
EX_SYNC_ALARM
T4_STS
-
INPUT_TO_T4
-
-
-
-
Bit
7
6
5
4
3-0
Name
Description
This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when an external sync alarm has
occurred, i.e., when the EX_SYNC_ALARM bit (b7, 0FH) is ‘1’.
EX_SYNC_ALARM
0: Disabled. (default)
1: Enabled.
This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the T4 DPLL locking status
changes (from ‘locked’ to ‘unlocked’ or from ‘unlocked’ to ‘locked’), i.e., when the T4_STS bit (b6, 0FH) is ‘1’.
T4_STS
0: Disabled. (default)
1: Enabled.
Reserved.
This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when all the input clocks for T4 path
change to be unqualified, i.e., when the INPUT_TO_T4 bit (b4, 0FH) is ‘1’.
INPUT_TO_T4
0: Disabled. (default)
1: Enabled.
Reserved.
Programming Information
61
December 3, 2008
IDT82V3255
6.2.3
WAN PLL
INPUT CLOCK FREQUENCY & PRIORITY CONFIGURATION REGISTERS
IN1_CMOS_CNFG - CMOS Input Clock 1 Configuration
Address: 16H
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
DIRECT_DIV
LOCK_8K
BUCKET_SEL1
BUCKET_SEL0
IN_FREQ3
IN_FREQ2
IN_FREQ1
IN_FREQ0
Bit
Name
Description
7
DIRECT_DIV
Refer to the description of the LOCK_8K bit (b6, 16H).
This bit, together with the DIRECT_DIV bit (b7, 16H), determines whether the DivN Divider or the Lock 8k Divider is used for
IN1_CMOS:
6
5-4
3-0
LOCK_8K
DIRECT_DIV bit
LOCK_8K bit
Used Divider
0
0
1
1
0
1
0
1
Both bypassed (default)
Lock 8k Divider
DivN Divider
Reserved
These bits select one of the four groups of leaky bucket configuration registers for IN1_CMOS:
00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default)
BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H.
10: Group 2; the addresses of the configuration registers are 39H ~ 3CH.
11: Group 3; the addresses of the configuration registers are 3DH ~ 40H.
These bits set the DPLL required frequency for IN1_CMOS:
0000: 8 kHz. (default)
0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘1’) / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘0’).
0010: 6.48 MHz.
0011: 19.44 MHz.
0100: 25.92 MHz.
IN_FREQ[3:0]
0101: 38.88 MHz.
0110 ~ 1000: Reserved.
1001: 2 kHz.
1010: 4 kHz.
1011 ~ 1111: Reserved.
For IN1_CMOS, the required frequency should not be set higher than that of the input clock.
Programming Information
62
December 3, 2008
IDT82V3255
WAN PLL
IN2_CMOS_CNFG - CMOS Input Clock 2 Configuration
Address: 17H
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
DIRECT_DIV
LOCK_8K
BUCKET_SEL1
BUCKET_SEL0
IN_FREQ3
IN_FREQ2
IN_FREQ1
IN_FREQ0
Bit
Name
Description
7
DIRECT_DIV
Refer to the description of the LOCK_8K bit (b6, 17H).
This bit, together with the DIRECT_DIV bit (b7, 17H), determines whether the DivN Divider or the Lock 8k Divider is used for
IN2_CMOS:
6
5-4
3-0
LOCK_8K
DIRECT_DIV bit
LOCK_8K bit
Used Divider
0
0
1
1
0
1
0
1
Both bypassed (default)
Lock 8k Divider
DivN Divider
Reserved
These bits select one of the four groups of leaky bucket configuration registers for IN2_CMOS:
00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default)
BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H.
10: Group 2; the addresses of the configuration registers are 39H ~ 3CH.
11: Group 3; the addresses of the configuration registers are 3DH ~ 40H.
These bits set the DPLL required frequency for IN2_CMOS:
0000: 8 kHz. (default)
0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘1’) / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘0’).
0010: 6.48 MHz.
0011: 19.44 MHz.
0100: 25.92 MHz.
IN_FREQ[3:0]
0101: 38.88 MHz.
0110 ~ 1000: Reserved.
1001: 2 kHz.
1010: 4 kHz.
1011 ~ 1111: Reserved.
For the IN2_CMOS, the required frequency should not be set higher than that of the input clock.
Programming Information
63
December 3, 2008
IDT82V3255
WAN PLL
IN1_IN2_DIFF_HF_DIV_CNFG - Differential Input Clock 1 & 2 High Frequency Divider Configuration
Address: 18H
Type: Read / Write
Default Value: 00XXXX00
7
6
5
4
3
2
1
0
IN2_DIFF_DIV1
IN2_DIFF_DIV0
-
-
-
-
IN1_DIFF_DIV1
IN1_DIFF_DIV0
Bit
Name
7-6
IN2_DIFF_DIV[1:0]
5-2
-
1-0
IN1_DIFF_DIV[1:0]
Programming Information
Description
These bits determine whether the HF Divider is used and what the division factor is for IN2_DIFF frequency division:
00: Bypassed. (default)
01: Divided by 4.
10: Divided by 5.
11: Reserved.
Reserved.
These bits determine whether the HF Divider is used and what the division factor is for IN1_DIFF frequency division:
00: Bypassed. (default)
01: Divided by 4.
10: Divided by 5.
11: Reserved.
64
December 3, 2008
IDT82V3255
WAN PLL
IN1_DIFF_CNFG - Differential Input Clock 1 Configuration
Address: 19H
Type: Read / Write
Default Value: 00000011
7
6
5
4
3
2
1
0
DIRECT_DIV
LOCK_8K
BUCKET_SEL1
BUCKET_SEL0
IN_FREQ3
IN_FREQ2
IN_FREQ1
IN_FREQ0
Bit
Name
Description
7
DIRECT_DIV
Refer to the description of the LOCK_8K bit (b6, 19H).
This bit, together with the DIRECT_DIV bit (b7, 19H), determines whether the DivN Divider or the Lock 8k Divider is used for
IN1_DIFF:
6
5-4
3-0
LOCK_8K
DIRECT_DIV bit
LOCK_8K bit
Used Divider
0
0
1
1
0
1
0
1
Both bypassed (default)
Lock 8k Divider
DivN Divider
Reserved
These bits select one of the four groups of leaky bucket configuration registers for IN1_DIFF:
00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default)
BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H.
10: Group 2; the addresses of the configuration registers are 39H ~ 3CH.
11: Group 3; the addresses of the configuration registers are 3DH ~ 40H.
These bits set the DPLL required frequency for IN1_DIFF:
0000: 8 kHz.
0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘1’) / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘0’).
0010: 6.48 MHz.
0011: 19.44 MHz. (default)
0100: 25.92 MHz.
IN_FREQ[3:0]
0101: 38.88 MHz.
0110 ~ 1000: Reserved.
1001: 2 kHz.
1010: 4 kHz.
1011 ~ 1111: Reserved.
The required frequency should not be set higher than that of the input clock.
Programming Information
65
December 3, 2008
IDT82V3255
WAN PLL
IN2_DIFF_CNFG - Differential Input Clock 2 Configuration
Address: 1AH
Type: Read / Write
Default Value: 00000011
7
6
5
4
3
2
1
0
DIRECT_DIV
LOCK_8K
BUCKET_SEL1
BUCKET_SEL0
IN_FREQ3
IN_FREQ2
IN_FREQ1
IN_FREQ0
Bit
Name
Description
7
DIRECT_DIV
Refer to the description of the LOCK_8K bit (b6, 1AH).
This bit, together with the DIRECT_DIV bit (b7, 1AH), determines whether the DivN Divider or the Lock 8k Divider is used for
IN2_DIFF:
6
5-4
3-0
LOCK_8K
DIRECT_DIV bit
LOCK_8K bit
Used Divider
0
0
1
1
0
1
0
1
Both bypassed (default)
Lock 8k Divider
DivN Divider
Reserved
These bits select one of the four groups of leaky bucket configuration registers for IN2_DIFF:
00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default)
BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H.
10: Group 2; the addresses of the configuration registers are 39H ~ 3CH.
11: Group 3; the addresses of the configuration registers are 3DH ~ 40H.
These bits set the DPLL required frequency for IN2_DIFF:
0000: 8 kHz.
0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘1’) / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘0’).
0010: 6.48 MHz.
0011: 19.44 MHz. (default)
0100: 25.92 MHz.
IN_FREQ[3:0]
0101: 38.88 MHz.
0110 ~ 1000: Reserved.
1001: 2 kHz.
1010: 4 kHz.
1011 ~ 1111: Reserved.
For IN2_DIFF, the required frequency should not be set higher than that of the input clock.
Programming Information
66
December 3, 2008
IDT82V3255
WAN PLL
IN3_CMOS_CNFG - CMOS Input Clock 3 Configuration
Address: 1DH
Type: Read / Write
Default Value: 00000011
7
6
5
4
3
2
1
0
DIRECT_DIV
LOCK_8K
BUCKET_SEL1
BUCKET_SEL0
IN_FREQ3
IN_FREQ2
IN_FREQ1
IN_FREQ0
Bit
Name
Description
7
DIRECT_DIV
Refer to the description of the LOCK_8K bit (b6, 1DH).
This bit, together with the DIRECT_DIV bit (b7, 1DH), determines whether the DivN Divider or the Lock 8k Divider is used for
IN3_CMOS:
6
5-4
3-0
LOCK_8K
DIRECT_DIV bit
LOCK_8K bit
Used Divider
0
0
1
1
0
1
0
1
Both bypassed (default)
Lock 8k Divider
DivN Divider
Reserved
These bits select one of the four groups of leaky bucket configuration registers for IN3_CMOS:
00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default)
BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H.
10: Group 2; the addresses of the configuration registers are 39H ~ 3CH.
11: Group 3; the addresses of the configuration registers are 3DH ~ 40H.
These bits set the DPLL required frequency for IN3_CMOS:
0000: 8 kHz.
0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘1’) / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is ‘0’).
0010: 6.48 MHz.
0011: 19.44 MHz. (default)
0100: 25.92 MHz.
IN_FREQ[3:0]
0101: 38.88 MHz.
0110 ~ 1000: Reserved.
1001: 2 kHz.
1010: 4 kHz.
1011 ~ 1111: Reserved.
For IN3_CMOS, the required frequency should not be set higher than that of the input clock.
Programming Information
67
December 3, 2008
IDT82V3255
WAN PLL
PRE_DIV_CH_CNFG - DivN Divider Channel Selection
Address: 23H
Type: Read / Write
Default Value: XXXX0000
7
6
5
4
3
2
1
0
-
-
-
-
PRE_DIV_CH_VALUE3
PRE_DIV_CH_VALUE2
PRE_DIV_CH_VALUE1
PRE_DIV_CH_VALUE0
Bit
Name
7-4
-
Description
Reserved.
This register is an indirect address register for Register 24H and 25H.
These bits select an input clock. The value set in the PRE_DIVN_VALUE[14:0] bits (25H, 24H) is available for the
selected input clock.
0000: Reserved. (default)
0001, 0010: Reserved.
0011: IN1_CMOS.
PRE_DIV_CH_VALUE[3:0]
0100: IN2_CMOS.
0101: IN1_DIFF.
0110: IN2_DIFF.
0111, 1000: Reserved.
1001: IN3_CMOS.
1010 ~ 1111: Reserved.
3-0
PRE_DIVN[7:0]_CNFG - DivN Divider Division Factor Configuration 1
Address: 24H
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
PRE_DIVN_VA
LUE7
PRE_DIVN_VA
LUE6
PRE_DIVN_VA
LUE5
PRE_DIVN_VA
LUE4
PRE_DIVN_VA
LUE3
PRE_DIVN_VA
LUE2
PRE_DIVN_VA
LUE1
PRE_DIVN_VA
LUE0
Bit
7-0
Name
Description
PRE_DIVN_VALUE[7:0] Refer to the description of the PRE_DIVN_VALUE[14:8] bits (b6~0, 25H).
Programming Information
68
December 3, 2008
IDT82V3255
WAN PLL
PRE_DIVN[14:8]_CNFG - DivN Divider Division Factor Configuration 2
Address: 25H
Type: Read / Write
Default Value: X0000000
7
6
5
4
3
2
1
0
-
PRE_DIVN_VAL
UE14
PRE_DIVN_VAL
UE13
PRE_DIVN_VAL
UE12
PRE_DIVN_VAL
UE11
PRE_DIVN_VAL
UE10
PRE_DIVN_VAL
UE9
PRE_DIVN_VAL
UE8
Bit
Name
Description
7
-
6-0
PRE_DIVN_VALUE[14:8]
Reserved.
If the value in the PRE_DIVN_VALUE[14:0] bits is plus 1, the division factor for an input clock will be gotten. The input
clock is selected by the PRE_DIV_CH_VALUE[3:0] bits (b3~0, 23H).
A value from ‘0’ to ‘4BEF’ (Hex) can be written into, corresponding to a division factor from 1 to 19440. The others are
reserved. So the DivN Divider only supports an input clock whose frequency is lower than (<) 155.52 MHz.
The division factor setting should observe the following order:
1. Write the lower eight bits of the division factor to the PRE_DIVN_VALUE[7:0] bits;
2. Write the higher eight bits of the division factor to the PRE_DIVN_VALUE[14:8] bits.
Programming Information
69
December 3, 2008
IDT82V3255
WAN PLL
IN1_IN2_CMOS_SEL_PRIORITY_CNFG - CMOS Input Clock 1 & 2 Priority Configuration *
Address: 27H
Type: Read / Write
Default Value: 00110010
7
6
5
4
3
2
1
0
IN2_CMOS_SE
L_PRIORITY3
IN2_CMOS_SE
L_PRIORITY2
IN2_CMOS_SE
L_PRIORITY1
IN2_CMOS_SE
L_PRIORITY0
IN1_CMOS_SE
L_PRIORITY3
IN1_CMOS_SE
L_PRIORITY2
IN1_CMOS_SE
L_PRIORITY1
IN1_CMOS_SE
L_PRIORITY0
Bit
7-4
3-0
Name
Description
These bits set the priority of the corresponding INn_CMOS. Here n is 2.
0000: Disable INn_CMOS for automatic selection.
0001: Priority 1.
0010: Priority 2.
0011: Priority 3. (default)
0100: Priority 4.
0101: Priority 5.
0110: Priority 6.
INn_CMOS_SEL_PRIORITY[3:0] 0111: Priority 7.
1000: Priority 8.
1001: Priority 9.
1010: Priority 10.
1011: Priority 11.
1100: Priority 12.
1101: Priority 13.
1110: Priority 14.
1111: Priority 15.
These bits set the priority of the corresponding INn_CMOS. Here n is 1.
0000: Disable INn_CMOS for automatic selection.
0001: Priority 1.
0010: Priority 2. (default)
0011: Priority 3.
0100: Priority 4.
0101: Priority 5.
0110: Priority 6.
INn_CMOS_SEL_PRIORITY[3:0] 0111: Priority 7.
1000: Priority 8.
1001: Priority 9.
1010: Priority 10.
1011: Priority 11.
1100: Priority 12.
1101: Priority 13.
1110: Priority 14.
1111: Priority 15.
Programming Information
70
December 3, 2008
IDT82V3255
WAN PLL
IN1_IN2_DIFF_SEL_PRIORITY_CNFG - Differential Input Clock 1 & 2 Priority Configuration *
Address: 28H
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
IN2_DIFF_SEL_
PRIORITY3
IN2_DIFF_SEL_
PRIORITY2
IN2_DIFF_SEL_
PRIORITY1
IN2_DIFF_SEL_
PRIORITY0
IN1_DIFF_SEL_
PRIORITY3
IN1_DIFF_SEL_
PRIORITY2
IN1_DIFF_SEL_
PRIORITY1
IN1_DIFF_SEL_
PRIORITY0
Bit
7-4
3-0
Name
Description
These bits set the priority of the corresponding INn_DIFF. Here n is 2.
0000: Disable INn_DIFF for automatic selection. (default)
0001: Priority 1.
0010: Priority 2.
0011: Priority 3.
0100: Priority 4.
0101: Priority 5.
0110: Priority 6.
INn_DIFF_SEL_PRIORITY[3:0] 0111: Priority 7.
1000: Priority 8.
1001: Priority 9.
1010: Priority 10.
1011: Priority 11.
1100: Priority 12.
1101: Priority 13.
1110: Priority 14.
1111: Priority 15.
These bits set the priority of the corresponding INn_DIFF. Here n is 1.
0000: Disable INn_DIFF for automatic selection. (default)
0001: Priority 1.
0010: Priority 2.
0011: Priority 3.
0100: Priority 4.
0101: Priority 5.
0110: Priority 6.
INn_DIFF_SEL_PRIORITY[3:0] 0111: Priority 7.
1000: Priority 8.
1001: Priority 9.
1010: Priority 10.
1011: Priority 11.
1100: Priority 12.
1101: Priority 13.
1110: Priority 14.
1111: Priority 15.
Programming Information
71
December 3, 2008
IDT82V3255
WAN PLL
IN3_CMOS_SEL_PRIORITY_CNFG - CMOS Input Clock 3 Priority Configuration *
Address: 2AH
Type: Read / Write
Default Value: XXXX0100
7
6
5
4
3
2
1
0
-
-
-
-
IN3_CMOS_SE
L_PRIORITY3
IN3_CMOS_SE
L_PRIORITY2
IN3_CMOS_SE
L_PRIORITY1
IN3_CMOS_SE
L_PRIORITY0
Bit
Name
7-4
-
3-0
Description
Reserved.
These bits set the priority of the corresponding IN3_CMOS.
0000: Disable INn for automatic selection.
0001: Priority 1.
0010: Priority 2.
0011: Priority 3.
0100: Priority 4. (default)
0101: Priority 5.
0110: Priority 6.
IN3_CMOS_SEL_PRIORITY[3:0] 0111: Priority 7.
1000: Priority 8.
1001: Priority 9.
1010: Priority 10.
1011: Priority 11.
1100: Priority 12.
1101: Priority 13.
1110: Priority 14.
1111: Priority 15.
Programming Information
72
December 3, 2008
IDT82V3255
6.2.4
WAN PLL
INPUT CLOCK QUALITY MONITORING CONFIGURATION & STATUS REGISTERS
FREQ_MON_FACTOR_CNFG - Factor of Frequency Monitor Configuration
Address: 2EH
Type: Read / Write
Default Value: XXXX1011
7
6
5
4
3
2
1
0
-
-
-
-
FREQ_MON_F
ACTOR3
FREQ_MON_F
ACTOR2
FREQ_MON_F
ACTOR1
FREQ_MON_F
ACTOR0
Bit
Name
7-4
-
3-0
Description
Reserved.
These bits determine a factor. The factor has a relationship with the frequency hard alarm threshold in ppm (refer to
the description of the ALL_FREQ_HARD_THRESHOLD[3:0] bits (b3~0, 2FH)) and with the frequency of the input
clock with respect to the master clock in ppm (refer to the description of the IN_FREQ_VALUE[7:0] bits (b7~0, 42H)).
The factor represents the accuracy of the frequency monitor and should be set according to the requirements of different applications.
0000: 0.0032.
0001: 0.0064.
0010: 0.0127.
0011: 0.0257.
FREQ_MON_FACTOR[3:0]
0100: 0.0514.
0101: 0.103.
0110: 0.206.
0111: 0.412.
1000: 0.823.
1001: 1.646.
1010: 3.292.
1011: 3.81. (default)
1100 - 1111: 4.6.
ALL_FREQ_MON_THRESHOLD_CNFG - Frequency Monitor Threshold for All Input Clocks Configuration
Address: 2FH
Type: Read / Write
Default Value: XXXX0011
7
6
5
4
3
2
1
0
-
-
-
-
ALL_FREQ_HARD_
THRESHOLD3
ALL_FREQ_HARD_
THRESHOLD2
ALL_FREQ_HARD_
THRESHOLD1
ALL_FREQ_HARD_
THRESHOLD0
Bit
Name
7-4
-
3-0
Description
Reserved.
These bits represent an unsigned integer. The frequency hard alarm threshold in ppm can be calculated as
follows:
ALL_FREQ_HARD_THRESHOLD[3:0] Frequency Hard Alarm Threshold (ppm) = (ALL_FREQ_HARD_THRESHOLD[3:0] + 1) X
FREQ_MON_FACTOR[3:0] (b3~0, 2EH)
This threshold is symmetrical about zero.
Programming Information
73
December 3, 2008
IDT82V3255
WAN PLL
UPPER_THRESHOLD_0_CNFG - Upper Threshold for Leaky Bucket Configuration 0
Address: 31H
Type: Read / Write
Default Value: 00000110
7
6
5
4
3
2
1
0
UPPER_THRE
SHOLD_0_DAT
A7
UPPER_THRE
SHOLD_0_DAT
A6
UPPER_THRE
SHOLD_0_DAT
A5
UPPER_THRE
SHOLD_0_DAT
A4
UPPER_THRE
SHOLD_0_DAT
A3
UPPER_THRE
SHOLD_0_DAT
A2
UPPER_THRE
SHOLD_0_DAT
A1
UPPER_THRE
SHOLD_0_DAT
A0
Bit
Name
Description
7-0
UPPER_THRESHOLD_0_DATA[7:0]
These bits set an upper threshold for the internal leaky bucket accumulator. When the number of the accumulated events is above this threshold, a no-activity alarm is raised.
LOWER_THRESHOLD_0_CNFG - Lower Threshold for Leaky Bucket Configuration 0
Address: 32H
Type: Read / Write
Default Value: 00000100
7
6
5
4
3
2
1
0
LOWER_THRE
SHOLD_0_DAT
A7
LOWER_THRE
SHOLD_0_DAT
A6
LOWER_THRE
SHOLD_0_DAT
A5
LOWER_THRE
SHOLD_0_DAT
A4
LOWER_THRE
SHOLD_0_DAT
A3
LOWER_THRE
SHOLD_0_DAT
A2
LOWER_THRE
SHOLD_0_DAT
A1
LOWER_THRE
SHOLD_0_DAT
A0
Bit
Name
Description
7-0
LOWER_THRESHOLD_0_DATA[7:0]
These bits set a lower threshold for the internal leaky bucket accumulator. When the number of the accumulated
events is below this threshold, the no-activity alarm is cleared.
BUCKET_SIZE_0_CNFG - Bucket Size for Leaky Bucket Configuration 0
Address: 33H
Type: Read / Write
Default Value: 00001000
7
6
5
4
3
2
1
0
BUCKET_SIZE
_0_DATA7
BUCKET_SIZE
_0_DATA6
BUCKET_SIZE
_0_DATA5
BUCKET_SIZE
_0_DATA4
BUCKET_SIZE
_0_DATA3
BUCKET_SIZE
_0_DATA2
BUCKET_SIZE
_0_DATA1
BUCKET_SIZE
_0_DATA0
Bit
Name
Description
7-0
BUCKET_SIZE_0_DATA[7:0]
These bits set a bucket size for the internal leaky bucket accumulator. If the number of the accumulated events reach
the bucket size, the accumulator will stop increasing even if further events are detected.
Programming Information
74
December 3, 2008
IDT82V3255
WAN PLL
DECAY_RATE_0_CNFG - Decay Rate for Leaky Bucket Configuration 0
Address: 34H
Type: Read / Write
Default Value: XXXXXX01
7
6
5
4
3
2
1
0
-
-
-
-
-
-
DECAY_RATE_
0_DATA1
DECAY_RATE_
0_DATA0
Bit
Name
7-2
-
Description
Reserved.
These bits set a decay rate for the internal leaky bucket accumulator:
00: The accumulator decreases by 1 in every 128 ms with no event detected.
DECAY_RATE_0_DATA[1:0] 01: The accumulator decreases by 1 in every 256 ms with no event detected. (default)
10: The accumulator decreases by 1 in every 512 ms with no event detected.
11: The accumulator decreases by 1 in every 1024 ms with no event detected.
1-0
UPPER_THRESHOLD_1_CNFG - Upper Threshold for Leaky Bucket Configuration 1
Address: 35H
Type: Read / Write
Default Value: 00000110
7
6
5
4
3
2
1
0
UPPER_THRE
SHOLD_1_DAT
A7
UPPER_THRE
SHOLD_1_DAT
A6
UPPER_THRE
SHOLD_1_DAT
A5
UPPER_THRE
SHOLD_1_DAT
A4
UPPER_THRE
SHOLD_1_DAT
A3
UPPER_THRE
SHOLD_1_DAT
A2
UPPER_THRE
SHOLD_1_DAT
A1
UPPER_THRE
SHOLD_1_DAT
A0
Bit
Name
Description
7-0
UPPER_THRESHOLD_1_DATA[7:0]
These bits set an upper threshold for the internal leaky bucket accumulator. When the number of the accumulated events is above this threshold, a no-activity alarm is raised.
LOWER_THRESHOLD_1_CNFG - Lower Threshold for Leaky Bucket Configuration 1
Address: 36H
Type: Read / Write
Default Value: 00000100
7
6
5
4
3
2
1
0
LOWER_THRE
SHOLD_1_DAT
A7
LOWER_THRE
SHOLD_1_DAT
A6
LOWER_THRE
SHOLD_1_DAT
A5
LOWER_THRE
SHOLD_1_DAT
A4
LOWER_THRE
SHOLD_1_DAT
A3
LOWER_THRE
SHOLD_1_DAT
A2
LOWER_THRE
SHOLD_1_DAT
A1
LOWER_THRE
SHOLD_1_DAT
A0
Bit
7-0
Name
Description
These bits set a lower threshold for the internal leaky bucket accumulator. When the number of the accumulated
LOWER_THRESHOLD_1_DATA[7:0]
events is below this threshold, the no-activity alarm is cleared.
Programming Information
75
December 3, 2008
IDT82V3255
WAN PLL
BUCKET_SIZE_1_CNFG - Bucket Size for Leaky Bucket Configuration 1
Address: 37H
Type: Read / Write
Default Value: 00001000
7
6
5
4
3
2
1
0
BUCKET_SIZE
_1_DATA7
BUCKET_SIZE
_1_DATA6
BUCKET_SIZE
_1_DATA5
BUCKET_SIZE
_1_DATA4
BUCKET_SIZE
_1_DATA3
BUCKET_SIZE
_1_DATA2
BUCKET_SIZE
_1_DATA1
BUCKET_SIZE
_1_DATA0
Bit
Name
Description
These bits set a bucket size for the internal leaky bucket accumulator. If the number of the accumulated events reach
BUCKET_SIZE_1_DATA[7:0]
the bucket size, the accumulator will stop increasing even if further events are detected.
7-0
DECAY_RATE_1_CNFG - Decay Rate for Leaky Bucket Configuration 1
Address: 38H
Type: Read / Write
Default Value: XXXXXX01
7
6
5
4
3
2
1
0
-
-
-
-
-
-
DECAY_RATE_
1_DATA1
DECAY_RATE_
1_DATA0
Bit
Name
7-2
-
Description
Reserved.
These bits set a decay rate for the internal leaky bucket accumulator:
00: The accumulator decreases by 1 in every 128 ms with no event detected.
DECAY_RATE_1_DATA[1:0] 01: The accumulator decreases by 1 in every 256 ms with no event detected. (default)
10: The accumulator decreases by 1 in every 512 ms with no event detected.
11: The accumulator decreases by 1 in every 1024 ms with no event detected.
1-0
UPPER_THRESHOLD_2_CNFG - Upper Threshold for Leaky Bucket Configuration 2
Address: 39H
Type: Read / Write
Default Value: 00000110
7
6
5
4
3
2
1
0
UPPER_THRE
SHOLD_2_DAT
A7
UPPER_THRE
SHOLD_2_DAT
A6
UPPER_THRE
SHOLD_2_DAT
A5
UPPER_THRE
SHOLD_2_DAT
A4
UPPER_THRE
SHOLD_2_DAT
A3
UPPER_THRE
SHOLD_2_DAT
A2
UPPER_THRE
SHOLD_2_DAT
A1
UPPER_THRE
SHOLD_2_DAT
A0
Bit
7-0
Name
Description
These bits set an upper threshold for the internal leaky bucket accumulator. When the number of the accumuUPPER_THRESHOLD_2_DATA[7:0]
lated events is above this threshold, a no-activity alarm is raised.
Programming Information
76
December 3, 2008
IDT82V3255
WAN PLL
LOWER_THRESHOLD_2_CNFG - Lower Threshold for Leaky Bucket Configuration 2
Address: 3AH
Type: Read / Write
Default Value: 00000100
7
6
5
4
3
2
1
0
LOWER_THRE
SHOLD_2_DAT
A7
LOWER_THRE
SHOLD_2_DAT
A6
LOWER_THRE
SHOLD_2_DAT
A5
LOWER_THRE
SHOLD_2_DAT
A4
LOWER_THRE
SHOLD_2_DAT
A3
LOWER_THRE
SHOLD_2_DAT
A2
LOWER_THRE
SHOLD_2_DAT
A1
LOWER_THRE
SHOLD_2_DAT
A0
Bit
Name
Description
7-0
LOWER_THRESHOLD_2_DATA[7:0]
These bits set a lower threshold for the internal leaky bucket accumulator. When the number of the accumulated events is below this threshold, the no-activity alarm is cleared.
BUCKET_SIZE_2_CNFG - Bucket Size for Leaky Bucket Configuration 2
Address: 3BH
Type: Read / Write
Default Value: 00001000
7
6
5
4
3
2
1
0
BUCKET_SIZE
_2_DATA7
BUCKET_SIZE
_2_DATA6
BUCKET_SIZE
_2_DATA5
BUCKET_SIZE
_2_DATA4
BUCKET_SIZE
_2_DATA3
BUCKET_SIZE
_2_DATA2
BUCKET_SIZE
_2_DATA1
BUCKET_SIZE
_2_DATA0
Bit
Name
Description
7-0
BUCKET_SIZE_2_DATA[7:0]
These bits set a bucket size for the internal leaky bucket accumulator. If the number of the accumulated events reach
the bucket size, the accumulator will stop increasing even if further events are detected.
DECAY_RATE_2_CNFG - Decay Rate for Leaky Bucket Configuration 2
Address: 3CH
Type: Read / Write
Default Value: XXXXXX01
7
6
5
4
3
2
1
0
-
-
-
-
-
-
DECAY_RATE_
2_DATA1
DECAY_RATE_
2_DATA0
Bit
Name
7-2
-
1-0
Description
Reserved.
These bits set a decay rate for the internal leaky bucket accumulator:
00: The accumulator decreases by 1 in every 128 ms with no event detected.
DECAY_RATE_2_DATA[1:0] 01: The accumulator decreases by 1 in every 256 ms with no event detected. (default)
10: The accumulator decreases by 1 in every 512 ms with no event detected.
11: The accumulator decreases by 1 in every 1024 ms with no event detected.
Programming Information
77
December 3, 2008
IDT82V3255
WAN PLL
UPPER_THRESHOLD_3_CNFG - Upper Threshold for Leaky Bucket Configuration 3
Address: 3DH
Type: Read / Write
Default Value: 00000110
7
6
5
4
3
2
1
0
UPPER_THRE
SHOLD_3_DAT
A7
UPPER_THRE
SHOLD_3_DAT
A6
UPPER_THRE
SHOLD_3_DAT
A5
UPPER_THRE
SHOLD_3_DAT
A4
UPPER_THRE
SHOLD_3_DAT
A3
UPPER_THRE
SHOLD_3_DAT
A2
UPPER_THRE
SHOLD_3_DAT
A1
UPPER_THRE
SHOLD_3_DAT
A0
Bit
Name
Description
7-0
UPPER_THRESHOLD_3_DATA[7:0]
These bits set an upper threshold for the internal leaky bucket accumulator. When the number of the accumulated events is above this threshold, a no-activity alarm is raised.
LOWER_THRESHOLD_3_CNFG - Lower Threshold for Leaky Bucket Configuration 3
Address: 3EH
Type: Read / Write
Default Value: 00000100
7
6
5
4
3
2
1
0
LOWER_THRE
SHOLD_3_DAT
A7
LOWER_THRE
SHOLD_3_DAT
A6
LOWER_THRE
SHOLD_3_DAT
A5
LOWER_THRE
SHOLD_3_DAT
A4
LOWER_THRE
SHOLD_3_DAT
A3
LOWER_THRE
SHOLD_3_DAT
A2
LOWER_THRE
SHOLD_3_DAT
A1
LOWER_THRE
SHOLD_3_DAT
A0
Bit
Name
Description
7-0
LOWER_THRESHOLD_3_DATA[7:0]
These bits set a lower threshold for the internal leaky bucket accumulator. When the number of the accumulated events is below this threshold, the no-activity alarm is cleared.
BUCKET_SIZE_3_CNFG - Bucket Size for Leaky Bucket Configuration 3
Address: 3FH
Type: Read / Write
Default Value: 00001000
7
6
5
4
3
2
1
0
BUCKET_SIZE
_3_DATA7
BUCKET_SIZE
_3_DATA6
BUCKET_SIZE
_3_DATA5
BUCKET_SIZE
_3_DATA4
BUCKET_SIZE
_3_DATA3
BUCKET_SIZE
_3_DATA2
BUCKET_SIZE
_3_DATA1
BUCKET_SIZE
_3_DATA0
Bit
Name
Description
7-0
BUCKET_SIZE_3_DATA[7:0]
These bits set a bucket size for the internal leaky bucket accumulator. If the number of the accumulated events reach
the bucket size, the accumulator will stop increasing even if further events are detected.
Programming Information
78
December 3, 2008
IDT82V3255
WAN PLL
DECAY_RATE_3_CNFG - Decay Rate for Leaky Bucket Configuration 3
Address: 40H
Type: Read / Write
Default Value: XXXXXX01
7
6
5
4
3
2
1
0
-
-
-
-
-
-
DECAY_RATE_
3_DATA1
DECAY_RATE_
3_DATA0
Bit
Name
7-2
-
Description
Reserved.
These bits set a decay rate for the internal leaky bucket accumulator:
00: The accumulator decreases by 1 in every 128 ms with no event detected.
DECAY_RATE_3_DATA[1:0] 01: The accumulator decreases by 1 in every 256 ms with no event detected. (default)
10: The accumulator decreases by 1 in every 512 ms with no event detected.
11: The accumulator decreases by 1 in every 1024 ms with no event detected.
1-0
IN_FREQ_READ_CH_CNFG - Input Clock Frequency Read Channel Selection
Address: 41H
Type: Read / Write
Default Value: XXXX0000
7
6
5
4
3
2
1
0
-
-
-
-
IN_FREQ_READ
_CH3
IN_FREQ_READ
_CH2
IN_FREQ_READ
_CH1
IN_FREQ_READ
_CH0
Bit
Name
7-4
-
3-0
Description
Reserved.
These bits select an input clock, the frequency of which with respect to the reference clock can be read.
0000: Reserved. (default)
0001, 0010: Reserved.
0011: IN1_CMOS.
0100: IN2_CMOS.
IN_FREQ_READ_CH[3:0]
0101: IN1_DIFF.
0110: IN2_DIFF.
0111, 1000: Reserved.
1001: IN3_CMOS.
1010 ~ 1111: Reserved.
Programming Information
79
December 3, 2008
IDT82V3255
WAN PLL
IN_FREQ_READ_STS - Input Clock Frequency Read Value
Address: 42H
Type: Read
Default Value: 00000000
7
6
5
4
3
2
1
0
IN_FREQ_VAL
UE7
IN_FREQ_VAL
UE6
IN_FREQ_VAL
UE5
IN_FREQ_VAL
UE4
IN_FREQ_VAL
UE3
IN_FREQ_VAL
UE2
IN_FREQ_VAL
UE1
IN_FREQ_VAL
UE0
Bit
7-0
Name
Description
These bits represent a 2’s complement signed integer. If the value is multiplied by the value in the
FREQ_MON_FACTOR[3:0] bits (b3~0, 2EH), the frequency of an input clock with respect to the reference clock in ppm will
IN_FREQ_VALUE[7:0]
be gotten. The input clock is selected by the IN_FREQ_READ_CH[3:0] bits (b3~0, 41H).
The value in these bits is updated every 16 seconds, starting when an input clock is selected.
Programming Information
80
December 3, 2008
IDT82V3255
WAN PLL
IN1_IN2_CMOS_STS - CMOS Input Clock 1 & 2 Status
Address: 44H
Type: Read
Default Value: X110X110
7
6
5
4
3
2
1
0
-
IN2_CMOS_FRE
Q_HARD_ALAR
M
IN2_CMOS_NO_
ACTIVITY_ALAR
M
IN2_CMOS_PH_
LOCK_ALARM
-
IN1_CMOS_FRE
Q_HARD_ALAR
M
IN1_CMOS_NO_
ACTIVITY_ALAR
M
IN1_CMOS_PH_
LOCK_ALARM
Bit
Name
Description
7
-
6
IN2_CMOS_FREQ_HARD_ALARM
5
IN2_CMOS_NO_ACTIVITY_ALARM
4
IN2_CMOS_PH_LOCK_ALARM
3
-
2
IN1_CMOS_FREQ_HARD_ALARM
1
IN1_CMOS_NO_ACTIVITY_ALARM
0
IN1_CMOS_PH_LOCK_ALARM
Reserved.
This bit indicates whether IN2_CMOS is in frequency hard alarm status.
0: No frequency hard alarm.
1: In frequency hard alarm status. (default)
This bit indicates whether IN2_CMOS is in no-activity alarm status.
0: No no-activity alarm.
1: In no-activity alarm status. (default)
This bit indicates whether IN2_CMOS is in phase lock alarm status.
0: No phase lock alarm. (default)
1: In phase lock alarm status.
If the PH_ALARM_TIMEOUT bit (b5, 09H) is ‘0’, this bit is cleared by writing ‘1’ to this bit; if the
PH_ALARM_TIMEOUT bit (b5, 09H) is ‘1’, this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0,
08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised.
Reserved.
This bit indicates whether IN1_CMOS is in frequency hard alarm status.
0: No frequency hard alarm.
1: In frequency hard alarm status. (default)
This bit indicates whether IN1_CMOS is in no-activity alarm status.
0: No no-activity alarm.
1: In no-activity alarm status. (default)
This bit indicates whether IN1_CMOS is in phase lock alarm status.
0: No phase lock alarm. (default)
1: In phase lock alarm status.
If the PH_ALARM_TIMEOUT bit (b5, 09H) is ‘0’, this bit is cleared by writing ‘1’ to this bit; if the
PH_ALARM_TIMEOUT bit (b5, 09H) is ‘1’, this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0,
08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised.
Programming Information
81
December 3, 2008
IDT82V3255
WAN PLL
IN1_IN2_DIFF_STS - Differential Input Clock 1 & 2 Status
Address: 45H
Type: Read
Default Value: X110X110
7
6
5
4
3
2
1
0
-
IN2_DIFF_FREQ
_HARD_ALARM
IN2_DIFF_NO_A
CTIVITY_ALARM
IN2_DIFF_PH_L
OCK_ALARM
-
IN1_DIFF_FREQ
_HARD_ALARM
IN1_DIFF_NO_A
CTIVITY_ALARM
IN1_DIFF_PH_L
OCK_ALARM
Bit
Name
Description
7
-
6
IN2_DIFF_FREQ_HARD_ALARM
5
IN2_DIFF_NO_ACTIVITY_ALARM
4
IN2_DIFF_PH_LOCK_ALARM
3
-
2
IN1_DIFF_FREQ_HARD_ALARM
1
IN1_DIFF_NO_ACTIVITY_ALARM
0
IN1_DIFF_PH_LOCK_ALARM
Reserved.
This bit indicates whether IN2_DIFF is in frequency hard alarm status.
0: No frequency hard alarm.
1: In frequency hard alarm status. (default)
This bit indicates whether IN2_DIFF is in no-activity alarm status.
0: No no-activity alarm.
1: In no-activity alarm status. (default)
This bit indicates whether IN2_DIFF is in phase lock alarm status.
0: No phase lock alarm. (default)
1: In phase lock alarm status.
If the PH_ALARM_TIMEOUT bit (b5, 09H) is ‘0’, this bit is cleared by writing ‘1’ to this bit; if the
PH_ALARM_TIMEOUT bit (b5, 09H) is ‘1’, this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0,
08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised.
Reserved.
This bit indicates whether IN1_DIFF is in frequency hard alarm status.
0: No frequency hard alarm.
1: In frequency hard alarm status. (default)
This bit indicates whether IN1_DIFF is in no-activity alarm status.
0: No no-activity alarm.
1: In no-activity alarm status. (default)
This bit indicates whether IN1_DIFF is in phase lock alarm status.
0: No phase lock alarm. (default)
1: In phase lock alarm status.
If the PH_ALARM_TIMEOUT bit (b5, 09H) is ‘0’, this bit is cleared by writing ‘1’ to this bit; if the
PH_ALARM_TIMEOUT bit (b5, 09H) is ‘1’, this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0,
08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised.
Programming Information
82
December 3, 2008
IDT82V3255
WAN PLL
IN3_CMOS_STS - CMOS Input Clock 3 Status
Address: 47H
Type: Read
Default Value: XXXXX110
7
6
5
4
3
2
1
0
-
-
-
-
-
IN3_CMOS_FRE
Q_HARD_ALAR
M
IN3_CMOS_NO_
ACTIVITY_ALAR
M
IN3_CMOS_PH_
LOCK_ALARM
Bit
Name
7-3
-
2
1
0
Description
Reserved.
This bit indicates whether IN3_CMOS is in frequency hard alarm status.
IN3_CMOS_FREQ_HARD_ALARM 0: No frequency hard alarm.
1: In frequency hard alarm status. (default)
This bit indicates whether IN3_CMOS is in no-activity alarm status.
IN3_CMOS_NO_ACTIVITY_ALARM 0: No no-activity alarm.
1: In no-activity alarm status. (default)
This bit indicates whether IN3_CMOS is in phase lock alarm status.
0: No phase lock alarm. (default)
1: In phase lock alarm status.
IN3_CMOS_PH_LOCK_ALARM
If the PH_ALARM_TIMEOUT bit (b5, 09H) is ‘0’, this bit is cleared by writing ‘1’ to this bit; if the
PH_ALARM_TIMEOUT bit (b5, 09H) is ‘1’, this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0,
08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised.
Programming Information
83
December 3, 2008
IDT82V3255
6.2.5
WAN PLL
T0 / T4 DPLL INPUT CLOCK SELECTION REGISTERS
INPUT_VALID1_STS - Input Clocks Validity 1
Address: 4AH
Type: Read
Default Value: XX0000XX
7
6
5
4
3
2
1
0
-
-
IN2_DIFF
IN1_DIFF
IN2_CMOS
IN1_CMOS
-
-
Bit
Name
Description
7-6
-
5-4
INn_DIFF
3-2
INn_CMOS
1-0
-
Reserved.
This bit indicates the validity of the corresponding INn_DIFF. Here n is 2 or 1.
0: Invalid. (default)
1: Valid.
This bit indicates the validity of the corresponding INn_CMOS. Here n is 2 or 1.
0: Invalid. (default)
1: Valid.
Reserved.
INPUT_VALID2_STS - Input Clocks Validity 2
Address: 4BH
Type: Read
Default Value: XXXXXXX0
7
6
5
4
3
2
1
0
-
-
-
-
-
-
-
IN3_CMOS
Bit
Name
7-1
-
0
IN3_CMOS
Programming Information
Description
Reserved.
This bit indicates the validity of the corresponding IN3_CMOS.
0: Invalid. (default)
1: Valid.
84
December 3, 2008
IDT82V3255
WAN PLL
PRIORITY_TABLE1_STS - Priority Status 1 *
Address: 4EH
Type: Read
Default Value: 00000000
7
6
5
4
3
2
1
0
HIGHEST_PRI
ORITY_VALIDA
TED3
HIGHEST_PRI
ORITY_VALIDA
TED2
HIGHEST_PRI
ORITY_VALIDA
TED1
HIGHEST_PRI
ORITY_VALIDA
TED0
CURRENTLY_S
ELECTED_INP
UT3
CURRENTLY_S
ELECTED_INP
UT2
CURRENTLY_S
ELECTED_INP
UT1
CURRENTLY_S
ELECTED_INP
UT0
Bit
7-4
3-0
Name
Description
These bits indicate a qualified input clock with the highest priority.
0000: No input clock is qualified. (default)
0001, 0010: Reserved.
0011: IN1_CMOS.
0100: IN2_CMOS.
HIGHEST_PRIORITY_VALIDATED[3:0]
0101: IN1_DIFF.
0110: IN2_DIFF.
0111, 1000: Reserved.
1001: IN3_CMOS.
1010 ~ 1111: Reserved.
These bits indicate the T0/T4 selected input clock.
0000: No input clock is selected; or the T4 selected input clock is the T0 DPLL output. (default)
0001, 0010: Reserved.
0011: IN1_CMOS is selected.
0100: IN2_CMOS is selected.
CURRENTLY_SELECTED_INPUT[3:0]
0101: IN1_DIFF is selected.
0110: IN2_DIFF is selected.
0111, 1000: Reserved.
1001: IN3_CMOS is selected.
1010 ~ 1111: Reserved.
Programming Information
85
December 3, 2008
IDT82V3255
WAN PLL
PRIORITY_TABLE2_STS - Priority Status 2 *
Address: 4FH
Type: Read
Default Value: 00000000
7
6
5
4
3
2
1
0
THIRD_HIGHE
ST_PRIORITY_
VALIDATED3
THIRD_HIGHE
ST_PRIORITY_
VALIDATED2
THIRD_HIGHE
ST_PRIORITY_
VALIDATED1
THIRD_HIGHE
ST_PRIORITY_
VALIDATED0
SECOND_HIGH
EST_PRIORITY
_VALIDATED3
SECOND_HIGH
EST_PRIORITY
_VALIDATED2
SECOND_HIGH
EST_PRIORITY
_VALIDATED1
SECOND_HIGH
EST_PRIORITY
_VALIDATED0
Bit
Name
Description
These bits indicate a qualified input clock with the third highest priority.
0000: No input clock is qualified. (default)
0001, 0010: Reserved.
0011: IN1_CMOS.
0100: IN2_CMOS.
THIRD_HIGHEST_PRIORITY_VALIDATED[3:0]
0101: IN1_DIFF.
0110: IN2_DIFF.
0111, 1000: Reserved.
1001: IN3_CMOS.
1010 ~ 1111: Reserved.
These bits indicate a qualified input clock with the second highest priority.
0000: No input clock is qualified. (default)
0001, 0010: Reserved.
0011: IN1_CMOS.
0100: IN2_CMOS.
SECOND_HIGHEST_PRIORITY_VALIDATED[3:0]
0101: IN1_DIFF.
0110: IN2_DIFF.
0111, 1000: Reserved.
1001: IN3_CMOS.
1010 ~ 1111: Reserved.
7-4
3-0
T0_INPUT_SEL_CNFG - T0 Selected Input Clock Configuration
Address: 50H
Type: Read / Write
Default Value: XXXX0000
7
6
5
4
3
2
1
0
-
-
-
-
T0_INPUT_SEL3
T0_INPUT_SEL2
T0_INPUT_SEL1
T0_INPUT_SEL0
Bit
Name
7-4
-
3-0
Description
Reserved.
This bit determines T0 input clock selection. It is valid only when the EXT_SW bit (b4, 0BH) is ‘0’.
0000: Automatic selection. (default)
0001, 0010: Reserved.
0011: Forced selection - IN1_CMOS is selected.
0100: Forced selection - IN2_CMOS is selected.
T0_INPUT_SEL[3:0]
0101: Forced selection - IN1_DIFF is selected.
0110: Forced selection - IN2_DIFF is selected.
0111, 1000: Reserved.
1001: Forced selection - IN3_CMOS is selected.
1010 ~ 1111: Reserved.
Programming Information
86
December 3, 2008
IDT82V3255
WAN PLL
T4_INPUT_SEL_CNFG - T4 Selected Input Clock Configuration
Address: 51H
Type: Read / Write
Default Value: X0000000
7
6
5
4
3
2
1
0
-
T4_LOCK_T0
T0_FOR_T4
T4_TEST_T0_PH
T4_INPUT_SEL3
T4_INPUT_SEL2
T4_INPUT_SEL1
T4_INPUT_SEL0
Bit
Name
7
-
6
5
4
3-0
Description
Reserved.
This bit determines whether the T4 DPLL locks to a T0 DPLL output or locks independently from the T0 DPLL.
T4_LOCK_T0
0: Independently from the T0 path. (default)
1: Locks to a 77.76 MHz or 8 kHz signal from the T0 DPLL 77.76 MHz path.
This bit is valid only when the T4_LOCK_T0 bit (b6, 51H) is ‘1’. It determines whether a 77.76 MHz or 8 kHz signal from the
T0 DPLL 77.76 MHz path is selected by the T4 DPLL.
T0_FOR_T4
0: 77.76 MHz. (default)
1: 8 kHz.
This bit determines whether T4 selected input clock is compared with the feedback signal of the T4 DPLL for T4 DPLL locking
or is compared with the T0 selected input clock to get the phase difference between T0 and T4 selected input clocks.
T4_TEST_T0_PH
0: The T4 DPLL output. (default)
1: The T0 selected input clock.
These bits are valid only when the T4_LOCK_T0 bit (b6, 51H) is ‘0’. They determines the T4 DPLL input clock selection.
0000: Automatic selection. (default)
0001, 0010: Reserved.
0011: Forced selection - IN1_CMOS is selected.
0100: Forced selection - IN2_CMOS is selected.
T4_INPUT_SEL[3:0]
0101: Forced selection - IN1_DIFF is selected.
0110: Forced selection - IN2_DIFF is selected.
0111, 1000: Reserved.
1001: Forced selection - IN3_CMOS is selected.
1010 ~ 1111: Reserved.
Programming Information
87
December 3, 2008
IDT82V3255
6.2.6
WAN PLL
T0 / T4 DPLL STATE MACHINE CONTROL REGISTERS
OPERATING_STS - DPLL Operating Status
Address: 52H
Type: Read
Default Value: 10000001
7
6
5
4
3
2
1
0
EX_SYNC_ALA
RM_MON
T4_DPLL_LO
CK
T0_DPLL_SOFT
_FREQ_ALARM
T4_DPLL_SOFT
_FREQ_ALARM
T0_DPLL_LO
CK
T0_DPLL_OPER
ATING_MODE2
T0_DPLL_OPER
ATING_MODE1
T0_DPLL_OPER
ATING_MODE0
Bit
7
6
5
4
3
2-0
Name
Description
This bit indicates whether the selected frame sync input signal is in external sync alarm status.
0: No external sync alarm.
1: In external sync alarm status. (default)
This bit indicates the T4 DPLL locking status.
T4_DPLL_LOCK
0: Unlocked. (default)
1: Locked.
This bit indicates whether the T0 DPLL is in soft alarm status.
T0_DPLL_SOFT_FREQ_ALARM 0: No T0 DPLL soft alarm. (default)
1: In T0 DPLL soft alarm status.
This bit indicates whether the T4 DPLL is in soft alarm status.
T4_DPLL_SOFT_FREQ_ALARM 0: No T4 DPLL soft alarm. (default)
1: In T4 DPLL soft alarm status.
This bit indicates the T0 DPLL locking status.
T0_DPLL_LOCK
0: Unlocked. (default)
1: Locked.
These bits indicate the current operating mode of T0 DPLL.
000: Reserved.
001: Free-Run. (default)
010: Holdover.
T0_DPLL_OPERATING_MODE[2:0] 011: Reserved.
100: Locked.
101: Pre-Locked2.
110: Pre-Locked.
111: Lost-Phase.
EX_SYNC_ALARM_MON
Programming Information
88
December 3, 2008
IDT82V3255
WAN PLL
T0_OPERATING_MODE_CNFG - T0 DPLL Operating Mode Configuration
Address: 53H
Type: Read / Write
Default Value: XXXXX000
7
6
5
4
3
2
1
0
-
-
-
-
-
T0_OPERATING_MODE2
T0_OPERATING_MODE1
T0_OPERATING_MODE0
Bit
Name
7-3
-
2-0
Description
Reserved.
These bits control the T0 DPLL operating mode.
000: Automatic. (default)
001: Forced - Free-Run.
010: Forced - Holdover.
T0_OPERATING_MODE[2:0] 011: Reserved.
100: Forced - Locked.
101: Forced - Pre-Locked2.
110: Forced - Pre-Locked.
111: Forced - Lost-Phase.
T4_OPERATING_MODE_CNFG - T4 DPLL Operating Mode Configuration
Address: 54H
Type: Read / Write
Default Value: XXXXX000
7
6
5
4
3
2
1
0
-
-
-
-
-
T4_OPERATING_MODE2
T4_OPERATING_MODE1
T4_OPERATING_MODE0
Bit
Name
7-3
-
2-0
Description
Reserved.
These bits control the T4 DPLL operating mode.
000: Automatic. (default)
001: Forced - Free-Run.
T4_OPERATING_MODE[2:0] 010: Forced - Holdover.
011: Reserved.
100: Forced - Locked.
101, 110, 111: Reserved.
Programming Information
89
December 3, 2008
IDT82V3255
6.2.7
WAN PLL
T0 / T4 DPLL & APLL CONFIGURATION REGISTERS
T0_DPLL_APLL_PATH_CNFG - T0 DPLL & APLL Path Configuration
Address: 55H
Type: Read / Write
Default Value: 00000X0X
7
6
5
4
3
2
1
0
T0_APLL_PATH
3
T0_APLL_PA
TH2
T0_APLL_PA
TH1
T0_APLL_PA
TH0
T0_GSM_OBSAI_
16E1_16T1_SEL1
T0_GSM_OBSAI_
16E1_16T1_SEL0
T0_12E1_24T1_
E3_T3_SEL1
T0_12E1_24T1_
E3_T3_SEL0
Bit
7-4
3-2
1-0
Name
Description
These bits select an input to the T0 APLL.
0000: The output of T0 DPLL 77.76 MHz path. (default)
0001: The output of T0 DPLL 12E1/24T1/E3/T3 path.
0010: The output of T0 DPLL 16E1/16T1 path.
0011: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path.
T0_APLL_PATH[3:0]
0100: The output of T4 DPLL 77.76 MHz path.
0101: The output of T4 DPLL 12E1/24T1/E3/T3 path.
0110: The output of T4 DPLL 16E1/16T1 path.
0111: The output of T4 DPLL GSM/GPS/16E1/16T1 path.
1XXX: Reserved.
These bits select an output clock from the T0 DPLL GSM/OBSAI/16E1/16T1 path.
00: 16E1.
01: 16T1.
T0_GSM_OBSAI_16E1_16T1_SEL[1:0] 10: GSM.
11: OBSAI.
The default value of the T0_GSM_OBSAI_16E1_16T1_SEL0 bit is determined by the SONET/SDH pin during reset.
These bits select an output clock from the T0 DPLL 12E1/24T1/E3/T3 path.
00: 12E1.
01: 24T1.
T0_12E1_24T1_E3_T3_SEL[1:0]
10: E3.
11: T3.
The default value of the T0_12E1_24T1_E3_T3_SEL0 bit is determined by the SONET/SDH pin during
reset.
Programming Information
90
December 3, 2008
IDT82V3255
WAN PLL
T0_DPLL_START_BW_DAMPING_CNFG - T0 DPLL Start Bandwidth & Damping Factor Configuration
Address: 56H
Type: Read / Write
Default Value: 01101111
7
6
5
4
3
2
1
0
T0_DPLL_STA
RT_DAMPING2
T0_DPLL_STA
RT_DAMPING1
T0_DPLL_STA
RT_DAMPING0
T0_DPLL_STA
RT_BW4
T0_DPLL_STA
RT_BW3
T0_DPLL_STA
RT_BW2
T0_DPLL_STA
RT_BW1
T0_DPLL_STA
RT_BW0
Bit
7-5
4-0
Name
Description
These bits set the starting damping factor for T0 DPLL.
000: Reserved.
001: 1.2.
010: 2.5.
T0_DPLL_START_DAMPING[2:0]
011: 5. (default)
100: 10.
101: 20.
110, 111: Reserved.
These bits set the starting bandwidth for T0 DPLL.
00XXX: Reserved.
01000: 0.1 Hz.
01001: 0.3 Hz.
01010: 0.6 Hz.
01011: 1.2 Hz.
01100: 2.5 Hz.
T0_DPLL_START_BW[4:0]
01101: 4 Hz.
01110: 8 Hz.
01111: 18 Hz. (default)
10000: 35 Hz.
10001: 70 Hz.
10010: 560 Hz.
10011 ~ 11111: Reserved.
Programming Information
91
December 3, 2008
IDT82V3255
WAN PLL
T0_DPLL_ACQ_BW_DAMPING_CNFG - T0 DPLL Acquisition Bandwidth & Damping Factor Configuration
Address: 57H
Type: Read / Write
Default Value: 01101111
7
6
5
4
3
2
1
0
T0_DPLL_ACQ
_DAMPING2
T0_DPLL_ACQ
_DAMPING1
T0_DPLL_ACQ
_DAMPING0
T0_DPLL_ACQ
_BW4
T0_DPLL_ACQ
_BW3
T0_DPLL_ACQ
_BW2
T0_DPLL_ACQ
_BW1
T0_DPLL_ACQ
_BW0
Bit
7-5
4-0
Name
Description
These bits set the acquisition damping factor for T0 DPLL.
000: Reserved.
001: 1.2.
010: 2.5.
T0_DPLL_ACQ_DAMPING[2:0]
011: 5. (default)
100: 10.
101: 20.
110, 111: Reserved.
These bits set the acquisition bandwidth for T0 DPLL.
00XXX: Reserved.
01000: 0.1 Hz.
01001: 0.3 Hz.
01010: 0.6 Hz.
01011: 1.2 Hz.
01100: 2.5 Hz.
T0_DPLL_ACQ_BW[4:0]
01101: 4 Hz.
01110: 8 Hz.
01111: 18 Hz. (default)
10000: 35 Hz.
10001: 70 Hz.
10010: 560 Hz.
10011 ~ 11111: Reserved.
Programming Information
92
December 3, 2008
IDT82V3255
WAN PLL
T0_DPLL_LOCKED_BW_DAMPING_CNFG - T0 DPLL Locked Bandwidth & Damping Factor Configuration
Address: 58H
Type: Read / Write
Default Value: 01101111
7
6
5
4
3
2
1
0
T0_DPLL_LOCK
ED_DAMPING2
T0_DPLL_LOCK
ED_DAMPING1
T0_DPLL_LOCK
ED_DAMPING0
T0_DPLL_LOC
KED_BW4
T0_DPLL_LOC
KED_BW3
T0_DPLL_LOC
KED_BW2
T0_DPLL_LOC
KED_BW1
T0_DPLL_LOC
KED_BW0
Bit
Name
7-5
4-0
Description
These bits set the locked damping factor for T0 DPLL.
000: Reserved.
001: 1.2.
010: 2.5.
T0_DPLL_LOCKED_DAMPING[2:0]
011: 5. (default)
100: 10.
101: 20.
110, 111: Reserved.
These bits set the locked bandwidth for T0 DPLL.
00XXX: Reserved.
01000: 0.1 Hz.
01001: 0.3 Hz.
01010: 0.6 Hz.
01011: 1.2 Hz. (default)
01100: 2.5 Hz.
T0_DPLL_LOCKED_BW[4:0]
01101: 4 Hz.
01110: 8 Hz.
01111: 18 Hz.
10000: 35 Hz.
10001: 70 Hz.
10010: 560 Hz.
10011 ~ 11111: Reserved.
T0_BW_OVERSHOOT_CNFG - T0 DPLL Bandwidth Overshoot Configuration
Address: 59H
Type: Read / Write
Default Value: 1XXX1XXX
7
6
5
4
3
2
1
0
AUTO_BW_SEL
-
-
-
T0_LIMT
-
-
-
Bit
7
6-4
3
2-0
Name
Description
This bit determines whether starting or acquisition bandwidth / damping factor is used for T0 DPLL.
0: The starting and acquisition bandwidths / damping factors are not used. Only the locked bandwidth / damping factor is used
AUTO_BW_SEL regardless of the T0 DPLL locking stage.
1: The starting, acquisition or locked bandwidth / damping factor is used automatically depending on different T0 DPLL locking
stages. (default)
Reserved.
This bit determines whether the integral path value is frozen when the T0 DPLL hard limit is reached.
T0_LIMT
0: Not frozen.
1: Frozen. It will minimize the subsequent overshoot when T0 DPLL is pulling in. (default)
Reserved.
Programming Information
93
December 3, 2008
IDT82V3255
WAN PLL
PHASE_LOSS_COARSE_LIMIT_CNFG - Phase Loss Coarse Detector Limit Configuration *
Address: 5AH
Type: Read / Write
Default Value: 10000101
7
6
5
4
3
2
1
0
COARSE_PH_L
OS_LIMT_EN
WIDE_EN
MULTI_PH_APP
MULTI_PH_8K_
4K_2K_EN
PH_LOS_COA
RSE_LIMT3
PH_LOS_COA
RSE_LIMT2
PH_LOS_COA
RSE_LIMT1
PH_LOS_COA
RSE_LIMT0
Bit
7
6
5
Name
Description
This bit controls whether the occurrence of the coarse phase loss will result in the T0/T4 DPLL unlocked.
COARSE_PH_LOS_LIMT_EN 0: Disabled.
1: Enabled. (default)
WIDE_EN
Refer to the description of the MULTI_PH_8K_4K_2K_EN bit (b4, 5AH).
This bit determines whether the PFD output of T0/T4 DPLL is limited to ±1 UI or is limited to the coarse phase limit.
0: Limited to ±1 UI. (default)
1: Limited to the coarse phase limit. When the selected input clock is of 2 kHz, 4 kHz or 8 kHz, the coarse phase limit depends
MULTI_PH_APP
on the MULTI_PH_8K_4K_2K_EN bit, the WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0] bits; when the selected input
clock is of other frequencies but 2 kHz, 4 kHz and 8 kHz, the coarse phase limit depends on the WIDE_EN bit and the
PH_LOS_COARSE_LIMT[3:0] bits. Refer to the description of the MULTI_PH_8K_4K_2K_EN bit (b4, 5AH) for details.
This bit, together with the WIDE_EN bit (b6, 5AH) and the PH_LOS_COARSE_LIMT[3:0] bits (b3~0, 5AH), determines the
coarse phase limit when the selected input clock is of 2 kHz, 4 kHz or 8 kHz. When the selected input clock is of other frequencies but 2 kHz, 4 kHz and 8 kHz, the coarse phase limit depends on the WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0]
bits.
Selected Input Clock MULTI_PH_8K_4K_2K_EN WIDE_EN
4
0
MULTI_PH_8K_4K_2K_EN
2 kHz, 4 kHz or 8 kHz
other than 2 kHz, 4
kHz and 8 kHz
1
don’t-care
0
1
0
don’t-care
1
Coarse Phase Limit
±1 UI
±1 UI
set by the PH_LOS_COARSE_LIMT[3:0] bits
(b3~0, 5AH).
±1 UI
set by the PH_LOS_COARSE_LIMT[3:0] bits
(b3~0, 5AH).
These bit set the coarse phase limit. The limit is used only in some cases. Refer to the description of the
MULTI_PH_8K_4K_2K_EN bit (b4, 5AH).
0000: ±1 UI.
0001: ±3 UI.
0010: ±7 UI.
0011: ±15 UI.
3 - 0 PH_LOS_COARSE_LIMT[3:0] 0100: ±31 UI.
0101: ±63 UI. (default)
0110: ±127 UI.
0111: ±255 UI.
1000: ±511 UI.
1001: ±1023 UI (T0); Reserved (T4).
1010-1111: Reserved.
Programming Information
94
December 3, 2008
IDT82V3255
WAN PLL
PHASE_LOSS_FINE_LIMIT_CNFG - Phase Loss Fine Detector Limit Configuration *
Address: 5BH
Type: Read / Write
Default Value: 10XXX010
7
6
5
4
3
2
1
0
FINE_PH_LOS_
LIMT_EN
FAST_LOS_SW
-
-
-
PH_LOS_FINE
_LIMT2
PH_LOS_FINE
_LIMT1
PH_LOS_FINE
_LIMT0
Bit
7
6
5-3
2-0
Name
Description
This bit controls whether the occurrence of the fine phase loss will result in the T0/T4 DPLL unlocked.
FINE_PH_LOS_LIMT_EN 0: Disabled.
1: Enabled. (default)
The value in this bit can be switched only when it is available for T0 path; this bit is always ‘1’ when it is available for T4
path.
This bit controls whether the occurrence of the fast loss will result in the T0/T4 DPLL unlocked.
FAST_LOS_SW
0: Does not result in the T0 DPLL unlocked. T0 DPLL will enter Temp-Holdover mode automatically. (default)
1: Results in the T0/T4 DPLL unlocked. For T0 path, T0 DPLL will enter Lost-Phase mode if the T0 DPLL operating
mode is switched automatically.
Reserved.
These bits set a fine phase limit.
000: 0.
001: ± (45 ° ~ 90 °).
010: ± (90 ° ~ 180 °). (default)
PH_LOS_FINE_LIMT[2:0] 011: ± (180 ° ~ 360 °).
100: ± (20 ns ~ 25 ns).
101: ± (60 ns ~ 65 ns).
110: ± (120 ns ~ 125 ns).
111: ± (950 ns ~ 955 ns).
Programming Information
95
December 3, 2008
IDT82V3255
WAN PLL
T0_HOLDOVER_MODE_CNFG - T0 DPLL Holdover Mode Configuration
Address: 5CH
Type: Read / Write
Default Value: 010001XX
7
6
5
4
3
2
1
0
MAN_HOLDOV
ER
AUTO_AVG
FAST_AVG
READ_AVG
TEMP_HOLDO
VER_MODE1
TEMP_HOLDO
VER_MODE0
-
-
Bit
Name
Description
7
6
MAN_HOLDOVER
AUTO_AVG
Refer to the description of the FAST_AVG bit (b5, 5CH).
Refer to the description of the FAST_AVG bit (b5, 5CH).
This bit, together with the AUTO_AVG bit (b6, 5CH) and the MAN_HOLDOVER bit (b7, 5CH), determines a frequency offset acquiring method in T0 DPLL Holdover Mode.
MAN_HOLDOVER
5
AUTO_AVG
FAST_AVG
Frequency Offset Acquiring Method
0
don’t-care
0
1
Automatic Instantaneous
Automatic Slow Averaged (default)
Automatic Fast Averaged
Manual
FAST_AVG
0
1
1
don’t-care
This bit controls the holdover frequency offset reading, which is read from the T0_HOLDOVER_FREQ[23:0] bits
(5FH ~ 5DH).
0: The value read from the T0_HOLDOVER_FREQ[23:0] bits (5FH ~ 5DH) is equal to the one written to them.
READ_AVG
(default)
1: The value read from the T0_HOLDOVER_FREQ[23:0] bits (5FH ~ 5DH) is not equal to the one written to them.
The value is acquired by Automatic Slow Averaged method if the FAST_AVG bit (b5, 5CH) is ‘0’; or is acquired by
Automatic Fast Averaged method if the FAST_AVG bit (b5, 5CH) is ‘1’.
These bits determine the frequency offset acquiring method in T0 DPLL Temp-Holdover Mode.
00: The method is the same as that used in T0 DPLL Holdover mode.
TEMP_HOLDOVER_MODE[1:0] 01: Automatic Instantaneous. (default)
10: Automatic Fast Averaged.
11: Automatic Slow Averaged.
Reserved.
4
3-2
1-0
T0_HOLDOVER_FREQ[7:0]_CNFG - T0 DPLL Holdover Frequency Configuration 1
Address: 5DH
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
T0_HOLDOVER
_FREQ7
T0_HOLDOVER
_FREQ6
T0_HOLDOVER
_FREQ5
T0_HOLDOVE
R_FREQ4
T0_HOLDOVE
R_FREQ3
T0_HOLDOVE
R_FREQ2
T0_HOLDOVE
R_FREQ1
T0_HOLDOVE
R_FREQ0
Bit
7-0
Name
Description
T0_HOLDOVER_FREQ[7:0] Refer to the description of the T0_HOLDOVER_FREQ[23:16] bits (b7~0, 5FH).
Programming Information
96
December 3, 2008
IDT82V3255
WAN PLL
T0_HOLDOVER_FREQ[15:8]_CNFG - T0 DPLL Holdover Frequency Configuration 2
Address: 5EH
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
T0_HOLDOVER
_FREQ15
T0_HOLDOVER
_FREQ14
T0_HOLDOVER
_FREQ13
T0_HOLDOVE
R_FREQ12
T0_HOLDOVE
R_FREQ11
T0_HOLDOVE
R_FREQ10
T0_HOLDOVE
R_FREQ9
T0_HOLDOVE
R_FREQ8
Bit
Name
7-0
Description
T0_HOLDOVER_FREQ[15:8] Refer to the description of the T0_HOLDOVER_FREQ[23:16] bits (b7~0, 5FH).
T0_HOLDOVER_FREQ[23:16]_CNFG - T0 DPLL Holdover Frequency Configuration 3
Address: 5FH
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
T0_HOLDOVER
_FREQ23
T0_HOLDOVER
_FREQ22
T0_HOLDOVER
_FREQ21
T0_HOLDOVE
R_FREQ20
T0_HOLDOVE
R_FREQ19
T0_HOLDOVE
R_FREQ18
T0_HOLDOVE
R_FREQ17
T0_HOLDOVE
R_FREQ16
Bit
7-0
Name
Description
The T0_HOLDOVER_FREQ[23:0] bits represent a 2’s complement signed integer.
In T0 DPLL Holdover mode, the value written to these bits multiplied by 0.000011 is the frequency offset set manuT0_HOLDOVER_FREQ[23:16]
ally; the value read from these bits multiplied by 0.000011 is the frequency offset automatically slow or fast averaged or manually set, as determined by the READ_AVG bit (b4, 5CH) and the FAST_AVG bit (b5, 5CH).
Programming Information
97
December 3, 2008
IDT82V3255
WAN PLL
T4_DPLL_APLL_PATH_CNFG - T4 DPLL & APLL Path Configuration
Address: 60H
Type: Read / Write
Default Value: 01000X0X
7
6
5
4
3
2
1
0
T4_APLL_PATH
3
T4_APLL_PA
TH2
T4_APLL_PA
TH1
T4_APLL_PA
TH0
T4_GSM_GPS_16
E1_16T1_SEL1
T4_GSM_GPS_16
E1_16T1_SEL0
T4_12E1_24T1_
E3_T3_SEL1
T4_12E1_24T1_
E3_T3_SEL0
Bit
7-4
3-2
1-0
Name
Description
These bits select an input to the T4 APLL.
0000: The output of T0 DPLL 77.76 MHz path.
0001: The output of T0 DPLL 12E1/24T1/E3/T3 path.
0010: The output of T0 DPLL 16E1/16T1 path.
0011: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path.
T4_APLL_PATH[3:0]
0100: The output of T4 DPLL 77.76 MHz path. (default)
0101: The output of T4 DPLL 12E1/24T1/E3/T3 path.
0110: The output of T4 DPLL 16E1/16T1 path.
0111: The output of T4 DPLL GSM/GPS/16E1/16T1 path.
1XXX: Reserved.
These bits select an output clock from the T4 DPLL GSM/GPS/16E1/16T1 path.
00: 16E1.
01: 16T1.
T4_GSM_GPS_16E1_16T1_SEL[1:0] 10: GSM.
11: GPS.
The default value of the T0_GSM_GPS_16E1_16T1_SEL0 bit is determined by the SONET/SDH pin during
reset.
These bits select an output clock from the T4 DPLL 12E1/24T1/E3/T3 path.
00: 12E1.
01: 24T1.
T4_12E1_24T1_E3_T3_SEL[1:0]
10: E3.
11: T3.
The default value of the T4_12E1_24T1_E3_T3_SEL0 bit is determined by the SONET/SDH pin during reset.
Programming Information
98
December 3, 2008
IDT82V3255
WAN PLL
T4_DPLL_LOCKED_BW_DAMPING_CNFG - T4 DPLL Locked Bandwidth & Damping Factor Configuration
Address: 61H
Type: Read / Write
Default Value: 011XXX00
7
6
5
4
3
2
1
0
T4_DPLL_LOCK
ED_DAMPING2
T4_DPLL_LOCK
ED_DAMPING1
T4_DPLL_LOCK
ED_DAMPING0
-
-
-
T4_DPLL_LOC
KED_BW1
T4_DPLL_LOC
KED_BW0
Bit
Name
7-5
4-2
1-0
Description
These bits set the locked damping factor for T4 DPLL.
000: Reserved.
001: 1.2.
010: 2.5.
T4_DPLL_LOCKED_DAMPING[2:0]
011: 5. (default)
100: 10.
101: 20.
110, 111: Reserved.
Reserved.
These bits set the locked bandwidth for T4 DPLL.
00: 18 Hz. (default)
T4_DPLL_LOCKED_BW[1:0]
01: 35 Hz.
10: 70 Hz.
11: 560 Hz.
CURRENT_DPLL_FREQ[7:0]_STS - DPLL Current Frequency Status 1 *
Address: 62H
Type: Read
Default Value: 00000000
7
6
5
4
3
2
1
0
CURRENT_DP
LL_FREQ7
CURRENT_DP
LL_FREQ6
CURRENT_DP
LL_FREQ5
CURRENT_DP
LL_FREQ4
CURRENT_DP
LL_FREQ3
CURRENT_DP
LL_FREQ2
CURRENT_DP
LL_FREQ1
CURRENT_DP
LL_FREQ0
Bit
Name
7-0
Description
CURRENT_DPLL_FREQ[7:0] Refer to the description of the CURRENT_DPLL_FREQ[23:16] bits (b7~0, 64H).
CURRENT_DPLL_FREQ[15:8]_STS - DPLL Current Frequency Status 2 *
Address: 63H
Type: Read
Default Value: 00000000
7
6
5
4
3
2
1
0
CURRENT_DP
LL_FREQ15
CURRENT_DP
LL_FREQ14
CURRENT_DP
LL_FREQ13
CURRENT_DP
LL_FREQ12
CURRENT_DP
LL_FREQ11
CURRENT_DP
LL_FREQ10
CURRENT_DP
LL_FREQ9
CURRENT_DP
LL_FREQ8
Bit
7-0
Name
Description
CURRENT_DPLL_FREQ[15:8] Refer to the description of the CURRENT_DPLL_FREQ[23:16] bits (b7~0, 64H).
Programming Information
99
December 3, 2008
IDT82V3255
WAN PLL
CURRENT_DPLL_FREQ[23:16]_STS - DPLL Current Frequency Status 3 *
Address: 64H
Type: Read
Default Value: 00000000
7
6
5
4
3
2
1
0
CURRENT_DP
LL_FREQ23
CURRENT_DP
LL_FREQ22
CURRENT_DP
LL_FREQ21
CURRENT_DP
LL_FREQ20
CURRENT_DP
LL_FREQ19
CURRENT_DP
LL_FREQ18
CURRENT_DP
LL_FREQ17
CURRENT_DP
LL_FREQ16
Bit
Name
Description
The CURRENT_DPLL_FREQ[23:0] bits represent a 2’s complement signed integer. If the value in these bits is mulCURRENT_DPLL_FREQ[23:16] tiplied by 0.000011, the current frequency offset of the T0/T4 DPLL output in ppm with respect to the master clock
will be gotten.
7-0
DPLL_FREQ_SOFT_LIMIT_CNFG - DPLL Soft Limit Configuration
Address: 65H
Type: Read / Write
Default Value: 10001100
7
6
5
4
3
2
1
0
FREQ_LIMT_P
H_LOS
DPLL_FREQ_S
OFT_LIMT6
DPLL_FREQ_S
OFT_LIMT5
DPLL_FREQ_S
OFT_LIMT4
DPLL_FREQ_S
OFT_LIMT3
DPLL_FREQ_S
OFT_LIMT2
DPLL_FREQ_S
OFT_LIMT1
DPLL_FREQ_S
OFT_LIMT0
Bit
Name
Description
This bit determines whether the T0/T4 DPLL in hard alarm status will result in it unlocked.
0: Disabled.
1: Enabled. (default)
These bits represent an unsigned integer. If the value is multiplied by 0.724, the DPLL soft limit for T0 and T4 paths in
DPLL_FREQ_SOFT_LIMT[6:0] ppm will be gotten.
The DPLL soft limit is symmetrical about zero.
7
FREQ_LIMT_PH_LOS
6-0
DPLL_FREQ_HARD_LIMIT[7:0]_CNFG - DPLL Hard Limit Configuration 1
Address: 66H
Type: Read / Write
Default Value: 10101011
7
6
5
4
3
2
1
0
DPLL_FREQ_H
ARD_LIMT7
DPLL_FREQ_H
ARD_LIMT6
DPLL_FREQ_H
ARD_LIMT5
DPLL_FREQ_H
ARD_LIMT4
DPLL_FREQ_H
ARD_LIMT3
DPLL_FREQ_H
ARD_LIMT2
DPLL_FREQ_H
ARD_LIMT1
DPLL_FREQ_H
ARD_LIMT0
Bit
7-0
Name
Description
DPLL_FREQ_HARD_LIMT[7:0] Refer to the description of the DPLL_FREQ_HARD_LIMT[15:8] bits (b7~0, 67H).
Programming Information
100
December 3, 2008
IDT82V3255
WAN PLL
DPLL_FREQ_HARD_LIMIT[15:8]_CNFG - DPLL Hard Limit Configuration 2
Address: 67H
Type: Read / Write
Default Value: 00011001
7
6
5
4
3
2
1
0
DPLL_FREQ_H
ARD_LIMT15
DPLL_FREQ_H
ARD_LIMT14
DPLL_FREQ_H
ARD_LIMT13
DPLL_FREQ_H
ARD_LIMT12
DPLL_FREQ_H
ARD_LIMT11
DPLL_FREQ_H
ARD_LIMT10
DPLL_FREQ_H
ARD_LIMT9
DPLL_FREQ_H
ARD_LIMT8
Bit
Name
7-0
Description
The DPLL_FREQ_HARD_LIMT[15:0] bits represent an unsigned integer. If the value is multiplied by 0.0014, the
DPLL_FREQ_HARD_LIMT[15:8] DPLL hard limit for T0 and T4 paths in ppm will be gotten.
The DPLL hard limit is symmetrical about zero.
CURRENT_DPLL_PHASE[7:0]_STS - DPLL Current Phase Status 1 *
Address: 68H
Type: Read
Default Value: 00000000
7
6
5
4
3
2
1
0
CURRENT_PH
_DATA7
CURRENT_PH
_DATA6
CURRENT_PH
_DATA5
CURRENT_PH
_DATA4
CURRENT_PH
_DATA3
CURRENT_PH
_DATA2
CURRENT_PH
_DATA1
CURRENT_PH
_DATA0
Bit
Name
7-0
Description
CURRENT_PH_DATA[7:0] Refer to the description of the CURRENT_PH_DATA[15:8] bits (b7~0, 69H).
CURRENT_DPLL_PHASE[15:8]_STS - DPLL Current Phase Status 2 *
Address: 69H
Type: Read
Default Value: 00000000
7
6
5
4
3
2
1
0
CURRENT_PH
_DATA15
CURRENT_PH
_DATA14
CURRENT_PH
_DATA13
CURRENT_PH
_DATA12
CURRENT_PH
_DATA11
CURRENT_PH
_DATA10
CURRENT_PH
_DATA9
CURRENT_PH
_DATA8
Bit
7-0
Name
Description
The CURRENT_PH_DATA[15:0] bits represent a 2’s complement signed integer. If the value is multiplied by 0.61, the
CURRENT_PH_DATA[15:8]
averaged phase error of the T0/T4 DPLL feedback with respect to the selected input clock in ns will be gotten.
Programming Information
101
December 3, 2008
IDT82V3255
WAN PLL
T0_T4_APLL_BW_CNFG - T0 / T4 APLL Bandwidth Configuration
Address: 6AH
Type: Read / Write
Default Value: XX01XX01
7
6
5
4
3
2
1
0
-
-
T0_APLL_BW1
T0_APLL_BW0
-
-
T4_APLL_BW1
T4_APLL_BW0
Bit
Name
7-6
-
5-4
3-2
1-0
Description
Reserved.
These bits set the bandwidth for T0 APLL.
00: 100 kHz.
T0_APLL_BW[1:0] 01: 500 kHz. (default)
10: 1 MHz.
11: 2 MHz.
Reserved.
These bits set the bandwidth for T4 APLL.
00: 100 kHz.
T4_APLL_BW[1:0] 01: 500 kHz. (default)
10: 1 MHz.
11: 2 MHz.
Programming Information
102
December 3, 2008
IDT82V3255
6.2.8
WAN PLL
OUTPUT CONFIGURATION REGISTERS
OUT2_FREQ_CNFG - Output Clock 2 Frequency Configuration
Address: 6DH
Type: Read / Write
Default Value: 00001000
7
6
5
4
3
2
1
0
OUT2_PATH_S
EL3
OUT2_PATH_S
EL2
OUT2_PATH_S
EL1
OUT2_PATH_S
EL0
OUT2_DIVIDER
3
OUT2_DIVIDER
2
OUT2_DIVIDER
1
OUT2_DIVIDER
0
Bit
7-4
3-0
Name
Description
These bits select an input to OUT2.
0000 ~ 0011: The output of T0 APLL. (default: 0000)
0100: The output of T0 DPLL 77.76 MHz path.
0101: The output of T0 DPLL 12E1/24T1/E3/T3 path.
0110: The output of T0 DPLL 16E1/16T1 path.
OUT2_PATH_SEL[3:0] 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path.
1000 ~ 1011: The output of T4 APLL.
1100: The output of T4 DPLL 77.76 MHz path.
1101: The output of T4 DPLL 12E1/24T1/E3/T3 path.
1110: The output of T4 DPLL 16E1/16T1 path.
1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path.
These bits select a division factor of the divider for OUT2.
The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output
OUT2_DIVIDER[3:0] (selected by the OUT2_PATH_SEL[3:0] bits (b7~4, 6DH)). If the signal is derived from one of the T0/T4 DPLL outputs,
please refer to Table 25 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to
Table 26 for the division factor selection.
Programming Information
103
December 3, 2008
IDT82V3255
WAN PLL
OUT1_FREQ_CNFG - Output Clock 1 Frequency Configuration
Address:71H
Type: Read / Write
Default Value: 00001000
7
6
5
4
3
2
1
0
OUT1_PATH_S
EL3
OUT1_PATH_S
EL2
OUT1_PATH_S
EL1
OUT1_PATH_S
EL0
OUT1_DIVIDER
3
OUT1_DIVIDER
2
OUT1_DIVIDER
1
OUT1_DIVIDER
0
Bit
Name
Description
These bits select an input to OUT1.
0000 ~ 0011: The output of T0 APLL. (default: 0000)
0100: The output of T0 DPLL 77.76 MHz path.
0101: The output of T0 DPLL 12E1/24T1/E3/T3 path.
0110: The output of T0 DPLL 16E1/16T1 path.
OUT1_PATH_SEL[3:0] 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path.
1000 ~ 1011: The output of T4 APLL.
1100: The output of T4 DPLL 77.76 MHz path.
1101: The output of T4 DPLL 12E1/24T1/E3/T3 path.
1110: The output of T4 DPLL 16E1/16T1 path.
1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path.
These bits select a division factor of the divider for OUT1.
The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output
OUT1_DIVIDER[3:0] (selected by the OUT1_PATH_SEL[3:0] bits (b7~4, 71H)). If the signal is derived from one of the T0/T4 DPLL outputs,
please refer to Table 25 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to
Table 26 for the division factor selection.
7-4
3-0
OUT1_INV_CNFG - Output Clock 1 Invert Configuration
Address:72H
Type: Read / Write
Default Value: XXXXXX0X
7
6
5
4
3
2
1
0
-
-
-
-
-
-
OUT1_INV
-
Bit
Name
7-2
-
1
OUT1_INV
0
-
Programming Information
Description
Reserved.
This bit determines whether the output on OUT1 is inverted.
0: Not inverted. (default)
1: Inverted.
Reserved.
104
December 3, 2008
IDT82V3255
WAN PLL
OUT2_INV_CNFG - Output Clock 2 Invert Configuration
Address:73H
Type: Read / Write
Default Value: XXXXX0XX
7
6
5
4
3
2
1
0
-
-
-
-
-
OUT2_INV
-
-
Bit
Name
7-3
-
2
OUT2_INV
1-0
-
Programming Information
Description
Reserved.
This bit determines whether the output on OUT2 is inverted.
0: Not inverted. (default)
1: Inverted.
Reserved.
105
December 3, 2008
IDT82V3255
WAN PLL
FR_MFR_SYNC_CNFG - Frame Sync & Multiframe Sync Output Configuration
Address:74H
Type: Read / Write
Default Value: 01100000
7
6
5
4
3
2
1
0
IN_2K_4K_8K_I
NV
8K_EN
2K_EN
2K_8K_PUL_P
OSITION
8K_INV
8K_PUL
2K_INV
2K_PUL
Bit
7
6
5
4
3
2
1
0
Name
Description
This bit determines whether the input clock is inverted before locked by the T0/T4 DPLL when the input clock is 2 kHz, 4
kHz or 8 kHz.
IN_2K_4K_8K_INV
0: Not inverted. (default)
1: Inverted.
This bit determines whether an 8 kHz signal is enabled to be output on FRSYNC_8K.
8K_EN
0: Disabled. FRSYNC_8K outputs low.
1: Enabled. (default)
This bit determines whether a 2 kHz signal is enabled to be output on MFRSYNC_2K.
2K_EN
0: Disabled. MFRSYNC_2K outputs low.
1: Enabled. (default)
This bit is valid only when FRSYNC_8K and/or MFRSYNC_2K output pulse; i.e., when one of the 8K_PUL bit (b2, 74H)
and the 2K_PUL bit (b0, 74H) is ‘1’ or when the 8K_PUL bit (b2, 74H) and the 2K_PUL bit (b0, 74H) are both ‘1’. It deter2K_8K_PUL_POSITION mines the pulse position referring to the standard 50:50 duty cycle.
0: Pulsed on the falling edge of the standard 50:50 duty cycle position. (default)
1: Pulsed on the rising edge of the standard 50:50 duty cycle position.
This bit determines whether the output on FRSYNC_8K is inverted.
8K_INV
0: Not inverted. (default)
1: Inverted.
This bit determines whether the output on FRSYNC_8K is 50:50 duty cycle or pulsed.
8K_PUL
0: 50:50 duty cycle. (default)
1: Pulsed. The pulse width is defined by the period of the output on OUT2.
This bit determines whether the output on MFRSYNC_2K is inverted.
2K_INV
0: Not inverted. (default)
1: Inverted.
This bit determines whether the output on MFRSYNC_2K is 50:50 duty cycle or pulsed.
2K_PUL
0: 50:50 duty cycle. (default)
1: Pulsed. The pulse width is defined by the period of the output on OUT2.
Programming Information
106
December 3, 2008
IDT82V3255
6.2.9
WAN PLL
PBO & PHASE OFFSET CONTROL REGISTERS
PHASE_MON_PBO_CNFG - Phase Transient Monitor & PBO Configuration
Address:78H
Type: Read / Write
Default Value: 0X000110
7
6
5
4
3
2
1
0
IN_NOISE_WIN
DOW
-
PH_MON_EN
PH_MON_PBO
_EN
PH_TR_MON_L
IMT3
PH_TR_MON_L
IMT2
PH_TR_MON_L
IMT1
PH_TR_MON_L
IMT0
Bit
Name
Description
This bit determines whether the input clock whose edge respect to the reference clock is outside ±5% is enabled to be
selected for T0/T4 DPLL.
IN_NOISE_WINDOW
0: Disabled. (default)
1: Enabled.
Reserved.
This bit is valid only when the PH_MON_PBO_EN bit (b4, 78H) is ‘1’. It determines whether the Phase Transient Monitor
is enabled to monitor the phase-time changes on the T0 selected input clock.
PH_MON_EN
0: Disabled. (default)
1: Enabled.
This bit determines whether a PBO event is triggered when the phase-time changes on the T0 selected input clock are
greater than a programmable limit over an interval of less than 0.1 seconds with the PH_MON_EN bit being ‘1’. The limit
PH_MON_PBO_EN is programmed by the PH_TR_MON_LIMT[3:0] bits (b3~0, 78H).
0: Disabled. (default)
1: Enabled.
These bits represent an unsigned integer. The Phase Transient Monitor limit in ns can be calculated as follows:
PH_TR_MON_LIMT[3:0]
Limit (ns) = (PH_TR_MON_LIMT[3:0] + 7) X 156.
7
6
5
4
3-0
PHASE_OFFSET[7:0]_CNFG - Phase Offset Configuration 1
Address:7AH
Type: Read / Write
Default Value: 00000000
7
6
5
4
3
2
1
0
PH_OFFSET7
PH_OFFSET6
PH_OFFSET5
PH_OFFSET4
PH_OFFSET3
PH_OFFSET2
PH_OFFSET1
PH_OFFSET0
Bit
7-0
Name
Description
PH_OFFSET[7:0] Refer to the description of the PH_OFFSET[9:8] bits (b1~0, 7BH).
Programming Information
107
December 3, 2008
IDT82V3255
WAN PLL
PHASE_OFFSET[9:8]_CNFG - Phase Offset Configuration 2
Address:7BH
Type: Read / Write
Default Value: 0XXXXX00
7
6
5
4
3
2
1
0
PH_OFFSET_E
N
-
-
-
-
-
PH_OFFSET9
PH_OFFSET8
Bit
7
6-2
1-0
Name
Description
This bit determines whether the input-to-output phase offset is enabled.
PH_OFFSET_EN 0: Disabled. (default)
1: Enabled.
Reserved.
These bits represent a 2’s complement signed integer. If the value is multiplied by 0.61, the input-to-output phase offset in ns
PH_OFFSET[9:8]
to adjust will be gotten.
Programming Information
108
December 3, 2008
IDT82V3255
6.2.10
WAN PLL
SYNCHRONIZATION CONFIGURATION REGISTERS
SYNC_MONITOR_CNFG - Sync Monitor Configuration
Address:7CH
Type: Read / Write
Default Value: 00101011
7
6
5
4
3
2
1
0
SYNC_BYPASS
SYNC_MON_LIMT2
SYNC_MON_LIMT1
SYNC_MON_LIMT0
-
-
-
-
Bit
7
6-4
3-0
Name
Description
This bit selects one frame sync input signal to synchronize the frame sync output signals.
0: EX_SYNC1 is selected. (default)
SYNC_BYPASS
1: When the T0 selected input clock is IN1_CMOS or IN1_DIFF, EX_SYNC1 is selected; when the T0 selected input clock
is IN2_CMOS or IN2_DIFF, EX_SYNC2 is selected; when the T0 selected input clock is IN3_CMOS, EX_SYNC3 is
selected; when there is no T0 selected input clock, no frame sync input signal is selected.
These bits set the limit for the external sync alarm.
000: ±1 UI.
001: ±2 UI.
010: ±3 UI. (default)
SYNC_MON_LIMT[2:0] 011: ±4 UI.
100: ±5 UI.
101: ±6 UI.
110: ±7 UI.
111: ±8 UI.
These bits must be set to ‘1011’.
Programming Information
109
December 3, 2008
IDT82V3255
WAN PLL
SYNC_PHASE_CNFG - Sync Phase Configuration
Address:7DH
Type: Read / Write
Default Value: XX000000
7
6
5
4
3
2
1
0
-
-
SYNC_PH31
SYNC_PH30
SYNC_PH21
SYNC_PH20
SYNC_PH11
SYNC_PH10
Bit
Name
Description
7-6
-
5-4
SYNC_PH3[1:0]
3-2
SYNC_PH2[1:0]
1-0
SYNC_PH1[1:0]
Reserved.
These bits set the sampling of EX_SYNC3 when EX_SYNC3 is enabled to synchronize the frame sync output signal. Nominally, the falling edge of EX_SYNC3 is aligned with the rising edge of the T0 selected input clock.
00: On target. (default)
01: 0.5 UI early.
10: 1 UI late.
11: 0.5 UI late.
These bits set the sampling of EX_SYNC2 when EX_SYNC2 is enabled to synchronize the frame sync output signal. Nominally, the falling edge of EX_SYNC2 is aligned with the rising edge of the T0 selected input clock.
00: On target. (default)
01: 0.5 UI early.
10: 1 UI late.
11: 0.5 UI late.
These bits set the sampling of EX_SYNC1 when EX_SYNC1 is enabled to synchronize the frame sync output signal. Nominally, the falling edge of EX_SYNC1 is aligned with the rising edge of the T0 selected input clock.
00: On target. (default)
01: 0.5 UI early.
10: 1 UI late.
11: 0.5 UI late.
Programming Information
110
December 3, 2008
IDT82V3255
7
WAN PLL
THERMAL MANAGEMENT
The junction temperature Tj can be calculated as follows:
Tj = TA + P X θJA = 85°C + 1.57W X 21.7°C/W = 119.1°C
The device operates over the industry temperature range -40°C ~
+85°C. To ensure the functionality and reliability of the device, the maximum junction temperature Tjmax should not exceed 125°C. In some
applications, the device will consume more power and a thermal solution
should be provided to ensure the junction temperature Tj does not
exceed the Tjmax.
7.1
The junction temperature of 119.1°C is below the maximum junction
temperature of 125°C so no extra heat enhancement is required.
In some operation environments, the calculated junction temperature
might exceed the maximum junction temperature of 125°C and an external thermal solution such as a heatsink is required.
7.3
JUNCTION TEMPERATURE
A heatsink is expanding the surface area of the device to which it is
attached. θJA is now a combination of device case and heat-sink thermal
resistance, as the heat flowing from the die junction to ambient goes
through the package and the heatsink. θJA can be calculated as follows:
Equation 2: θJA = θJC + θCH+ θHA
Junction temperature Tj is the temperature of package typically at the
geographical center of the chip where the device's electrical circuits are.
It can be calculated as follows:
Equation 1: Tj = TA + P X θJA
Where:
θJA = Junction-to-Ambient Thermal Resistance of the Package
Where:
θJC = Junction-to-Case Thermal Resistance
θCH = Case-to-Heatsink Thermal Resistance
θHA = Heatsink-to-Ambient Thermal Resistance
Tj = Junction Temperature
TA = Ambient Temperature
P = Device Power Consumption
θCH+ θHA determines which heatsink and heatsink attachment can
In order to calculate junction temperature, an appropriate θJA must
be used. The θJA is shown in Table 36:
be selected to ensure the junction temperature does not exceed the
maximum junction temperature. According to Equation 1 and 2,
Power consumption is the core power excluding the power dissipated
in the loads. Table 35 provides power consumption in special environments.
θCH+ θHA can be calculated as follows:
Equation 3: θCH+ θHA = (Tj - TA) / P - θJC
Assume:
Table 35: Power Consumption and Maximum Junction Temperature
Package
Power
Consumption (W)
Operating
Voltage
(V)
1.57
1.57
3.6
3.6
LQFP/PP64
TQFP/EDG64
7.2
Tj = 125°C (Tjmax)
Maximum
TA (°C)
Junction
Temperature (°C)
85
85
HEATSINK EVALUATION
TA = 85°C
P = 1.57W
θJC = 12.6°C/W (TQFP/EDG64)
125
125
θCH+ θHA can be calculated as follows:
θCH+ θHA = (125°C - 85°C ) / 1.57W - 12.6°C/W = 12.9°C/W
EXAMPLE OF JUNCTION TEMPERATURE
CALCULATION
That is, if a heatsink and heatsink attachment whose θCH+ θHA is
below or equal to 12.9°C/W is used in such operation environment, the
junction temperature will not exceed the maximum junction temperature.
Assume:
TA = 85°C
θJA = 21.7°C/W (TQFP/EDG64 Soldered & when airfow rate is 0 m/
s)
P = 1.57W
Table 36: Thermal Data
Package
Pin Count
Thermal Pad
θJC (°C/W)
θJB (°C/W)
LQFP/PP64
TQFP/EDG64
TQFP/EDG64
64
64
64
No
Yes/Exposed
Yes/Soldered
12.3
12.6
12.6
35.1
35.3
1.3
Thermal Management
111
θJA (°C/W) Air Flow in m/s
0
1
2
3
4
5
43.1
37.0
21.7
40
32.1
17.3
38.1
30.4
16.2
37.3
29.4
15.6
36.5
28.7
15.2
36.1
28.1
14.9
December 3, 2008
IDT82V3255
WAN PLL
8
ELECTRICAL SPECIFICATIONS
8.1
ABSOLUTE MAXIMUM RATING
Table 37: Absolute Maximum Rating
Symbol
Parameter
Min
Max
Unit
VDD
Supply Voltage VDD
-0.5
3.6
V
VIN
Input Voltage (non-supply pins)
5.5
V
VOUT
Output Voltage (non-supply pins)
5.5
V
TA
Ambient Operating Temperature Range
-40
+85
°C
TSTOR
Storage Temperature
-50
+150
°C
8.2
RECOMMENDED OPERATION CONDITIONS
Table 38: Recommended Operation Conditions
Symbol
Parameter
Min
Typ
Max
Unit
VDD
Power Supply (DC voltage) VDD
3.0
3.3
3.6
V
TA
Ambient Temperature Range
-40
+85
°C
IDD
Supply Current
388
436
mA
PTOT
Total Power Dissipation
1.28
1.57
W
Electrical Specifications
112
Test Condition
Exclude the loading
current and power
December 3, 2008
IDT82V3255
WAN PLL
8.3
I/O SPECIFICATIONS
8.3.1
CMOS INPUT / OUTPUT PORT
From Table 39 to Table 42, VDD is 3.3 V.
Table 39: CMOS Input Port Electrical Characteristics
Parameter
Description
Min
VIH
Input Voltage High
0.7VDD
VIL
Input Voltage Low
IIN
Input Current
VIN
Input Voltage
Typ
Max
Unit
Test Condition
V
-0.5
0.2VDD
V
10
µA
5.5
V
Max
Unit
Table 40: CMOS Input Port with Internal Pull-Up Resistor Electrical Characteristics
Parameter
Description
Min
VIH
Input Voltage High
0.7VDD
VIL
Input Voltage Low
PU
Pull-Up Resistor
IIN
Input Current
VIN
Input Voltage
Typ
Test Condition
V
10
-0.5
0.2VDD
V
80
KΩ
250
µA
5.5
V
Table 41: CMOS Input Port with Internal Pull-Down Resistor Electrical Characteristics
Parameter
Description
Min
VIH
Input Voltage High
0.7VDD
VIL
Input Voltage Low
PD
Pull-Down Resistor
IIN
Input Current
VIN
Input Voltage
Typ
Max
-0.5
Test Condition
V
0.2VDD
10
5
100
Unit
80
40
300
350
700
40
5.5
V
other CMOS input port with internal pull-down resistor
TRST and TCK pin
SDI, CLKE pin
other CMOS input port with internal pull-down resistor
TRST and TCK pin
SDI, CLKE pin
KΩ
µA
V
Table 42: CMOS Output Port Electrical Characteristics
Application Pin
Parameter
Description
Min
VOH
Output Voltage High
VOL
Output Voltage Low
tR
Rise time
3
tF
Fall time
3
Output Clock
Typ
Max
Unit
Test Condition
2.4
VDD
V
IOH = 8 mA
0
0.4
V
IOL = 8 mA
4
ns
15 pF
4
ns
15 pF
2.5
VDD
V
IOH = 4 mA
0
0.4
V
IOL= 4 mA
VOH
Output Voltage High
VOL
Output Voltage Low
tR
Rise Time
10
ns
50 pF
tF
Fall Time
10
ns
50 pF
Other Output
Electrical Specifications
113
December 3, 2008
IDT82V3255
WAN PLL
8.3.2
PECL / LVDS INPUT / OUTPUT PORT
8.3.2.1
PECL Input / Output Port
130 Ω 82 Ω
VDD (+ 3.3 V)
GND
50 Ω (transmission line)
2
kHz
OUT1_POS
to
667 MHz
OUT1_NEG
50 Ω (transmission line)
VDD (+ 3.3 V)
GND
130 Ω 82 Ω
VDD (+ 3.3 V)
130 Ω
50 Ω (transmission line)
2 kHz
to
667 MHz
IN1_POS
82 Ω
GND
VDD (+ 3.3 V)
50 Ω (transmission line)
130 Ω
IN1_NEG
Figure 19. Recommended PECL Output Port Line Termination
82 Ω
GND
VDD (+ 3.3 V)
50 Ω (transmission line)
130 Ω
IN2_POS
82 Ω
2 kHz
to
667 MHz
GND
VDD (+ 3.3 V)
130 Ω
50 Ω (transmission line)
IN2_NEG
82 Ω
GND
Figure 18. Recommended PECL Input Port Line Termination
Electrical Specifications
114
December 3, 2008
IDT82V3255
WAN PLL
Table 43: PECL Input / Output Port Electrical Characteristics
Parameter
Description
Min
Max
Unit
VDD - 2.5
VDD - 0.5
V
VDD - 2.4
VDD - 0.4
V
Input Differential Voltage
0.1
1.4
V
VIL_S
Input Low Voltage, Single-ended Input 2
VDD - 2.4
VDD - 1.5
V
VIH_S
VDD - 1.3
VDD - 0.5
V
IIH
Input High Voltage, Single-ended Input 2
Input High Current, Input Differential Voltage VID = 1.4 V
-10
10
µA
IIL
Input Low Current, Input Differential Voltage VID = 1.4 V
-10
10
µA
VOL
Output Voltage Low 3
VDD - 2.1
VDD - 1.62
V
VOH
Output Voltage High 3
VDD - 1.25
VDD - 0.88
V
VOD
Output Differential Voltage3
580
900
mV
tRISE
Output Rise time (20% to 80%)
200
300
pS
tFALL
Output Fall time (20% to 80%)
200
300
pS
tSKEW
Output Differential Skew
50
pS
VIL
Input Low Voltage, Differential Inputs
1
VIH
Input High Voltage, Differential Inputs 1
VID
Typ
Test Condition
Note:
1. Assuming a differential input voltage of at least 100 mV.
2. Unused differential input terminated to VDD-1.4 V.
3. With 50 Ω load on each pin to VDD-2 V, i.e. 82 to GND and 130 to VDD.
Electrical Specifications
115
December 3, 2008
IDT82V3255
8.3.2.2
WAN PLL
LVDS Input / Output Port
2 kHz
to
667 MHz
50 Ω (transmission line)
OUT1_POS
IN1_POS
100 Ω
100 Ω
50 Ω (transmission line)
50 Ω (transmission line)
OUT1_NEG
IN1_NEG
50 Ω (transmission line)
IN2_POS
2 kHz
to
100 Ω
667 MHz
IN2_NEG
50 Ω (transmission line)
50 Ω (transmission line)
2 kHz
to
667 MHz
Figure 21. Recommended LVDS Output Port Line Termination
Figure 20. Recommended LVDS Input Port Line Termination
Table 44: LVDS Input / Output Port Electrical Characteristics
Parameter
Description
VCM
Min
Typ
Max
Unit
VDIFF
Input Common-mode Voltage Range
0
1200
2400
mV
Input Peak Differential Voltage
100
900
mV
-100
100
mV
Test Condition
VIDTH
Input Differential Threshold
RTERM
External Differential Termination Impedance
95
105
Ω
VOH
Output Voltage High
1350
1475
mV
VOL
Output Voltage Low
925
1100
mV
RLOAD = 100 Ω ± 1%
100
RLOAD = 100 Ω ± 1%
VOD
Differential Output Voltage
250
400
mV
RLOAD = 100 Ω ± 1%
VOS
Output Offset Voltage
1125
1275
mV
RLOAD = 100 Ω ± 1%
80
RO
Differential Output Impedance
120
Ω
VCM = 1.0 V or 1.4 V
∆RO
RO Mismatch between A and B
20
%
VCM = 1.0 V or 1.4 V
∆VOD
Change in VOD between Logic 0 and Logic 1
25
mV
RLOAD = 100 Ω ± 1%
25
mV
RLOAD = 100 Ω ± 1%
100
∆VOS
Change in VOS between Logic 0 and Logic 1
ISA, ISB
Output Current
24
mA
Driver shorted to GND
ISAB
Output Current
12
mA
Driver shorted together
tRISE
Output Rise time (20% to 80%)
200
300
pS
RLOAD = 100 Ω ± 1%
tFALL
Output Fall time (20% to 80%)
200
300
pS
RLOAD = 100 Ω ± 1%
tSKEW
Output Differential Skew
50
pS
RLOAD = 100 Ω ± 1%
Electrical Specifications
116
December 3, 2008
IDT82V3255
8.4
WAN PLL
JITTER & WANDER PERFORMANCE
Table 45: Output Clock Jitter Generation
Test Definition 1
Peak to Peak
Typ
RMS
Typ
N x 2.048MHz without APLL
N x 2.048MHz with T0/T4 APLL
N x 1.544 MHz without APLL
N x 1.544 MHz with T0/T4 APLL
44.736 MHz with T0/T4 APLL
44.736 MHz without APLL
34.368 MHz with T0/T4 APLL
34.368 MHz without APLL
<2 ns
<1 ns
<2 ns
<1 ns
<1 ns
<2 ns
<1 ns
<2 ns
<200 ps
<100 ps
<200 ps
<100 ps
<100 ps
<200 ps
<100 ps
<200 ps
0.004 UI p-p 0.001 UI RMS
OC-3
(Chip T0 DPLL + T0/T4 APLL) 6.48 MHz, 19.44 MHz, 25.92
0.004 UI p-p 0.001 UI RMS
MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz,
311.04 MHz, 622.08 MHz output
0.001 UI p-p 0.001 UI RMS
0.018 UI p-p 0.007 UI RMS
OC-12
(Chip T0 DPLL + T0/T4 APLL) 6.48 MHz, 19.44 MHz, 25.92
MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz,
0.028 UI p-p 0.009 UI RMS
311.04 MHz, 622.08 MHz output + Intel GD16523 + Optical
transceiver)
0.002 UI p-p 0.001 UI RMS
STM-16
0.162 UI p-p 0.03 UI RMS
(Chip T0 DPLL + T0/T4 APLL) 6.48 MHz, 19.44 MHz, 25.92
MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz,
311.04 MHz, 622.08 MHz output + Intel GD16523 + Optical
0.01 UI p-p 0.009 UI RMS
transceiver)
Note
Test Filter
See Table 46: Output Clock Phase Noise for details
See Table 46: Output Clock Phase Noise for details
See Table 46: Output Clock Phase Noise for details
See Table 46: Output Clock Phase Noise for details
GR-253, G.813 Option 2
limit 0.1 UI p-p
(1 UI-6430 ps)
G.813 Option 1, G.812
limit 0.5 UI p-p
(1 UI-6430 ps)
G.813 Option 1
limit 0.1 UI p-p
(1 UI-6430 ps)
GR-253, G.813 Option 2
limit 0.1 UI p-p
(1 UI-1608 ps)
G.813 Option 1, G.812
limit 0.5 UI p-p
(1 UI-1608 ps)
G.813 Option 1, G.812
limit 0.1 UI p-p
(1 UI-160 8ps)
G.813 Option 1, G.812
limit 0.5 UI p-p
(1 UI-402 ps)
G.813 Option 1, G.812
limit 0.1 UI p-p
(1 UI-402 ps)
20 Hz - 100 kHz
20 Hz - 100 kHz
10 Hz - 40 kHz
10 Hz - 40 kHz
100 Hz - 800 kHz
100 Hz - 800 kHz
10 Hz - 400 kHz
10 Hz - 400 kHz
12 kHz - 1.3 MHz
500 Hz - 1.3 MHz
65 kHz - 1.3 MHz
12 kHz - 5 MHz
1 kHz - 5 MHz
250 kHz - 5 MHz
5 kHz - 20 MHz
1 MHz - 20 MHz
Note:
1. CMAC E2747 TCXO is used.
Electrical Specifications
117
December 3, 2008
IDT82V3255
WAN PLL
Table 46: Output Clock Phase Noise
Output Clock 1
@100Hz Offset
Typ
@1kHz Offset
Typ
622.08 MHz (T0 DPLL + T0/T4 APLL)
155.52 MHz (T0 DPLL + T0/T4 APLL)
38.88 MHz (T0 DPLL + T0/T4 APLL)
16E1 (T0/T4 APLL)
16T1 (T0/T4 APLL)
E3 (T0/T4 APLL)
T3 (T0/T4 APLL)
-70
-82
-94
-94
-95
-93
-92
-86
-98
-110
-110
-112
-109
-108
@10kHz Offset @100kHz Offset
Typ
Typ
-95
-107
-118
-118
-120
-116
-116
-100
-112
-124
-125
-127
-124
-122
@1MHz Offset @5MHz Offset
Typ
Typ
-107
-119
-131
-131
-132
-131
-126
-128
-140
-143
-142
-143
-138
-141
Unit
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
Note:
1. CMAC E2747 TCXO is used.
Table 47: Input Jitter Tolerance (155.52 MHz)
Table 49: Input Jitter Tolerance (2.048 MHz)
Jitter Frequency
Jitter Tolerance Amplitude (UI p-p)
Jitter Frequency
Jitter Tolerance Amplitude (UI p-p)
12 µHz
178 µHz
1.6 mHz
15.6 mHz
0.125 Hz
19.3 Hz
500 Hz
6.5 kHz
65 kHz
1.3 MHz
> 2800
> 2800
> 311
> 311
> 39
> 39
> 1.5
> 1.5
> 0.15
> 0.15
1 Hz
5 Hz
20 Hz
300 Hz
400 Hz
700 Hz
2400 Hz
10 kHz
50 kHz
100 kHz
150
140
130
40
33
18
5.5
1.3
0.4
0.4
Table 48: Input Jitter Tolerance (1.544 MHz)
Table 50: Input Jitter Tolerance (8 kHz)
Jitter Frequency
Jitter Tolerance Amplitude (UI p-p)
Jitter Frequency
Jitter Tolerance Amplitude (UI p-p)
1 Hz
5 Hz
20 Hz
300 Hz
400 Hz
700 Hz
2400 Hz
10 kHz
40 kHz
150
140
130
38
25
15
5
1.2
0.5
1 Hz
5 Hz
20 Hz
300 Hz
400 Hz
700 Hz
2400 Hz
3600 Hz
0.8
0.7
0.6
0.16
0.14
0.07
0.02
0.01
Electrical Specifications
118
December 3, 2008
IDT82V3255
WAN PLL
Table 51: T0 DPLL Jitter Transfer & Damping Factor
Table 52: T4 DPLL Jitter Transfer & Damping Factor
3 dB Bandwidth
Programmable Damping Factor
3 dB Bandwidth
Programmable Damping Factor
0.1 Hz
0.3 Hz
0.6 Hz
1.2 Hz
2.5 Hz
4 Hz
8 Hz
18 Hz
35 Hz
70 Hz
560 Hz
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
18 Hz
35 Hz
70 Hz
560 Hz
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
1.2, 2.5, 5, 10, 20
Electrical Specifications
119
December 3, 2008
IDT82V3255
8.5
WAN PLL
OUTPUT WANDER GENERATION
template
template
tested result
tested result
Figure 22. Output Wander Generation
Electrical Specifications
120
December 3, 2008
IDT82V3255
8.6
WAN PLL
INPUT / OUTPUT CLOCK TIMING
The inputs and outputs are aligned ideally. But due to the circuit delays, there is delay between the inputs and outputs.
8 kHz Input Clock
t1
8 kHz Output Clock
6.48 MHz Input Clock
t2
6.48 MHz Output Clock
19.44 MHz Input Clock
t3
19.44 MHz Output Clock
25.92 MHz Input Clock
t4
25.92 MHz Output Clock
38.88 MHz Input Clock
t5
38.88 MHz Output Clock
51.84 MHz Input Clock
t6
51.84 MHz Output Clock
Figure 23. Input / Output Clock Timing
Table 53: Input/Output Clock Timing
Symbol
Typical Delay 1 (ns)
Peak to Peak Delay Variation (ns)
t1
4
1.6
t2
1
1.6
t3
1
1.6
t4
2
1.6
t5
1.4
1.6
t6
3
1.6
Note:
1. Typical delay provided as reference only.
2. ‘Peak to Peak Delay Variation’ is the delay variation that is guaranteed not to be exceeded for IN11 in Master/Slave operation.
3. Tested when IN11 is selected.
Electrical Specifications
121
December 3, 2008
IDT82V3255
8.7
WAN PLL
OUTPUT CLOCK TIMING
MFRSYNC_2K/
FRSYNC_8K
N X T1 (1.544 MHz)
t1
N X E1 (2.048 MHz)
t2
E3 (34.368 MHz)
t3
t4
T3 (44.736 MHz)
t5
6.48 MHz
t6
19.44 MHz
t7
25.92 MHz
t8
38.88 MHz
t9
51.84 MHz
t10
77.76 MHz
t11
155.52 MHz
t12
311.04 MHz
t13
622.08 MHz
Table 54: Output Clock Timing
Symbol
Typical Delay (ns)
Peak to Peak Delay Variation (ns)
t1
0
2
t2
0
2
t3
0
2
t4
0
2
t5
0
2
t6
0
2
t7
0
2
t8
0
2
2
t9
0
t10
0
2
t11
0
1.5
t12
0
1.5 (not recommended to use)
t13
0
1.5 (not recommended to use)
Electrical Specifications
122
December 3, 2008
Glossary
3G
---
Third Generation
ADSL
---
Asymmetric Digital Subscriber Line
AMI
---
Alternate Mark Inversion
APLL
---
Analog Phase Locked Loop
ATM
---
Asynchronous Transfer Mode
BITS
---
Building Integrated Timing Supply
CMOS
---
Complementary Metal-Oxide Semiconductor
DCO
---
Digital Controlled Oscillator
DPLL
---
Digital Phase Locked Loop
DSL
---
Digital Subscriber Line
DSLAM
---
Digital Subscriber Line Access MUX
DWDM
---
Dense Wavelength Division Multiplexing
EPROM
---
Erasable Programmable Read Only Memory
GPS
---
Global Positioning System
GSM
---
Global System for Mobile Communications
IIR
---
Infinite Impulse Response
IP
---
Internet Protocol
ISDN
---
Integrated Services Digital Network
JTAG
---
Joint Test Action Group
LOS
---
Loss Of Signal
LPF
---
Low Pass Filter
LVDS
---
Low Voltage Differential Signal
MTIE
---
Maximum Time Interval Error
MUX
---
Multiplexer
OBSAI
---
Open Base Station Architecture Initiative
OC-n
---
Optical Carried rate, n = 1, 3, 12, 48, 192, 768; 51 Mbit/s, 155 Mbit/s, 622 Mbit/s, 2.5 Gbit/s, 10 Gbit/s, 40 Gbit/s.
Glossary
123
December 3, 2008
IDT82V3255
WAN PLL
PBO
---
Phase Build-Out
PDH
---
Plesiochronous Digital Hierarchy
PECL
---
Positive Emitter Coupled Logic
PFD
---
Phase & Frequency Detector
PLL
---
Phase Locked Loop
RMS
---
Root Mean Square
PRS
---
Primary Reference Source
SDH
---
Synchronous Digital Hierarchy
SEC
---
SDH / SONET Equipment Clock
SMC
---
SONET Minimum Clock
SONET
---
Synchronous Optical Network
SSU
---
Synchronization Supply Unit
STM
---
Synchronous Transfer Mode
TCM-ISDN
---
Time Compression Multiplexing Integrated Services Digital Network
TDEV
---
Time Deviation
UI
---
Unit Interval
WLL
---
Wireless Local Loop
Glossary
124
December 3, 2008
Index
A
Frequency Hard Alarm .................................................................21, 26
Averaged Phase Error ........................................................................ 31
Frequency Hard Alarm Threshold ...................................................... 21
B
H
Bandwidths and Damping Factors ..................................................... 31
Acquisition Bandwidth and Damping Factor ............................... 31
Locked Bandwidth and Damping Factor ..................................... 31
Starting Bandwidth and Damping Factor .................................... 31
Hard Limit ........................................................................................... 24
Holdover Frequency Offset ................................................................ 32
C
IIR ...................................................................................................... 32
Calibration .......................................................................................... 17
Input Clock Frequency ....................................................................... 21
Coarse Phase Loss ............................................................................ 24
Input Clock Selection ......................................................................... 22
Automatic selection ..............................................................23, 26
External Fast selection .........................................................22, 26
Forced selection ...................................................................23, 26
I
Crystal Oscillator ................................................................................ 17
Current Frequency Offset ................................................................... 31
Internal Leaky Bucket Accumulator ................................................... 20
Bucket Size ................................................................................ 20
Decay Rate ................................................................................ 20
Lower Threshold ........................................................................ 20
Upper Threshold ........................................................................ 20
D
DCO ................................................................................................... 31
Division Factor .................................................................................... 19
DPLL Hard Alarm ............................................................................... 24
L
DPLL Hard Limit ................................................................................. 24
Limit ................................................................................................... 34
DPLL Operating Mode ................................................................. 31, 32
Free-Run mode ................................................................... 31, 32
Holdover mode .................................................................... 31, 32
Automatic Fast Averaged ................................................... 32
Automatic Instantaneous .................................................... 32
Automatic Slow Averaged .................................................. 32
Manual ................................................................................ 32
Locked mode ....................................................................... 31, 32
Temp-Holdover mode ......................................................... 31
Lost-Phase mode ....................................................................... 31
Pre-Locked mode ....................................................................... 31
Pre-Locked2 mode ..................................................................... 32
LPF .................................................................................................... 31
M
Master Clock ...................................................................................... 17
Microprocessor Interface ................................................................... 43
N
No-activity Alarm ..........................................................................20, 26
P
PBO ................................................................................................... 34
DPLL Soft Alarm ................................................................................. 24
PFD .................................................................................................... 31
DPLL Soft Limit .................................................................................. 24
Phase Lock Alarm ........................................................................25, 26
E
Phase Offset ...................................................................................... 34
External Sync Alarm ........................................................................... 38
Phase-compared ..........................................................................24, 34
F
Phase-time ......................................................................................... 34
Fast Loss ............................................................................................ 24
Pre-Divider ......................................................................................... 19
DivN Divider ............................................................................... 19
Fine Phase Loss ................................................................................. 24
Index
125
December 3, 2008
IDT82V3255
WAN PLL
HF Divider ................................................................................... 19
Lock 8k Divider ........................................................................... 19
Non-Revertive switch ................................................................. 27
Revertive switch ......................................................................... 26
R
State Machine ..............................................................................28, 30
Reference Clock ................................................................................. 21
V
S
Validity ............................................................................................... 26
Selected Input Clock Switch ............................................................... 26
Index
126
December 3, 2008
IDT82V3255
WAN PLL
PACKAGE DIMENSIONS
Figure 24. 64-Pin PP Package Dimensions (a) (in Millimeters)
Package Dimensions
127
December 3, 2008
IDT82V3255
WAN PLL
Figure 25. 64-Pin PP Package Dimensions (b) (in Millimeters)
Package Dimensions
128
December 3, 2008
IDT82V3255
WAN PLL
Figure 26. 64-Pin EDG Package Dimensions (a) (in Millimeters)
Package Dimensions
129
December 3, 2008
IDT82V3255
WAN PLL
Figure 27. 64-Pin EDG Package Dimensions (b) (in Millimeters)
Package Dimensions
130
December 3, 2008
IDT82V3255
WAN PLL
Figure 28. EDG64 Recommended Land Pattern with Exposed Pad (in Millimeters)
Package Dimensions
131
December 3, 2008
IDT82V3255
WAN PLL
ORDERING INFORMATION
XXXXXXX
Device Type
XX
X
Process/
Temperature
Range
Blank
Industrial (-40 °C to +85 °C)
TF
TFG
EDG
Thin Quad Flatpack (LQFP, PP64)
Green Thin Quad Flatpack (LQFP, PPG64)
Green Thermal Enhanced Thin Quad Flatpack, ExposedPadTM (TQFP, EDG64)
82V3255
WAN PLL
DATASHEET DOCUMENT HISTORY
09/28/2005 pgs. 112.
06/19/2006 pgs. 41
03/14/2007 pgs. 111
11/18/2008 pgs. 111, 112, 117, 127, 128, 129, 130, 131, 132
12/03/2008 pg. 132
for SALES:
1-800-345-7015 or 408-284-8200
fax: 408-284-2775
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
www.idt.com
IDT and the IDT logo are trademarks of Integrated Device Technology, Inc.
132
for Tech Support:
408-360-1552
email:[email protected]