VISHAY BY229X-200

ADVANCED INFORMATION
ADVANCED INFORMATION
ADVANCED INFORMATION
BY229X SERIES
FAST SWITCHING PLASTIC RECTIFIER
Reverse Voltage - 50 to 600 Volts
Forward Current - 8.0 Amperes
ITO-220AC
FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ Glass passivated chip junction
♦ Low leakage, high voltage
♦ High surge current capability
♦ Superfast recovery time, for high efficiency
♦ High temperature soldering guaranteed:
250°C, 0.25" (6.35mm) from case for 10 seconds
0.188 (4.77)
0.172 (4.36)
0.405 (10.27)
0.383 (9.72)
0.110 (2.80)
0.100 (2.54)
0.131 (3.39)
DIA.
0.122 (3.08)
0.140 (3.56)
DIA.
0.130 (3.30)
0.600 (15.5)
0.580 (14.5)
0.676 (17.2)
0.646 (16.4)
PIN
1
0.350 (8.89)
0.330 (8.38)
2
MECHANICAL DATA
0.191 (4.85)
0.171 (4.35)
0.560 (14.22)
0.530 (13.46)
Case: JEDEC ITO-220AC fully overmolded plastic body
over passivated chip
Terminals: Plated lead solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Weight: 0.064 ounce, 1.81 grams
Mounting Torque: 5 in. - lbs. max.
0.110 (2.80)
0.100 (2.54)
0.060 (1.52)
0.037 (0.94)
0.027 (0.69)
0.022 (0.55)
0.014 (0.36)
0.205 (5.20)
0.195 (4.95)
PIN 1
PIN 2
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS
BY229X
-200
BY229X
-400
BY229X
-600
BY229X
-800
UNITS
Maximum recurrent peak reverse voltage
VRRM
200
400
600
800
Volts
Maximum RMS voltage
VRMS
140
280
420
560
Volts
Maximum DC blocking voltage
VDC
200
400
600
800
Volts
Maximum average forward rectified current
at TC=100°C
I(AV)
8.0
Amps
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
IFSM
100
Amps
VF
1.85
Volts
IR
10.0
300
µA
Maximum reverse recovery time (NOTE 1)
trr
145
ns
Maximum recovered stored charge (NOTE 2)
Qrr
700
nC
Maximum slope of reverse recovery current (NOTE 2)
dir/dt
60
A/µs
Maximum thermal resistance (NOTE 3)
RΘJC
4.8
°C/W
Typical thermal resistance, junction to air
RΘJA
20
°C/W
TJ, TSTG
-40 to +150
°C
VISOL
4500 (NOTE 4)
3500 (NOTE 5)
1500 (NOTE 6)
Volts
Maximum instantaneous forward voltage at 20A
Maximum DC reverse current
at rated DC blocking voltage
TJ=25°C
at TJ=125°C
Operating junction and storage temperature range
RMS Isolation voltage from terminals to heatsink
with RH ≤ 30%
NOTES:
(1) Reverse recovery test conditions: IF=1A, VR=30V, di/dt=50A/µs, Irr=10% IRM
(2) Qrr test conditions: IF=2A, VR=30V, di/dt=20A/µs
(3) Thermal resistance from junction to case mounted on heatsink with heatsink compound
(4) Clip mounting, where lead does not overlap heatsink with 0.110” offset.
(5) Clip mounting, where leads do overlap heatsink.
(6) Screw mounting, where washer diameter is ≤ 4.9 mm (0.19”).
10/12/98
RATINGS AND CHARACTERISTIC CURVES BY229X SERIES
FIG. 1 - MAXIMUM FORWARD CURRENT
DERATING CURVES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
10
150
RESISTIVE OR
INDUCTIVE LOAD
TL=75°C
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
125
PEAK FORWARD SURGE
CURRENT, AMPERES
AVERAGE FORWARD RECTIFIED
CURRENT, AMPERES
12
8
6
4
2
100
75
50
25
0
0
50
100
150
0
CASE AMBIENT TEMPERATURE, °C
100
10
1
NUMBER OF CYCLES AT 60 HZ
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS
1000
TJ=150°C
TJ=150°C
10
TJ=25°C
1
TJ=100°C
TJ=125°C
0.1
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
INSTANTANEOUS REVERSE LEAKAGE CURRENT,
MICROAMPERES
INSTANTANEOUS FORWARD CURRENT,
AMPERES
100
100
TJ=125°C
10
TJ=100°C
1
TJ=25°C
0.10
0.01
100
0
20
40
60
80
Cj / pF
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
10
1
10
VR / V
100
100