Product Bulletin Surface Mount Ceramic Chip Capacitors – C0402 Series - C0G Dielectric Outline Drawing L W TIN PLATE T B NICKEL PLATE S ELECTRODES CONDUCTIVE METALLIZATION Dimensions – Millimeters (Inches) EIA Size Metric Size Code Code 0402 1005 L Length W Width B Bandwidth S Separation 1.0 (.039) ± 0.05 (.002) 0.5 (.020) ± 0.05 (.002) 0.25 (.010) ± 0.10 (.004) - See Capacitance Value Table below for thickness dimension. Capacitance Value Capacitance Value (pF) KEMET Part Number Voltage Capacitance Tolerance Thickness Qty 7" Reel Qty 13" Reel 120 C0402C121J5GAC 50 ±5% 0.5 (.020) ± 0.05 (.002) 10,000 50,000 150 C0402C151J5GAC 50 ±5% 0.5 (.020) ± 0.05 (.002) 10,000 50,000 180 C0402C181J5GAC 50 ±5% 0.5 (.020) ± 0.05 (.002) 10,000 50,000 220 C0402C221J5GAC 50 ±5% 0.5 (.020) ± 0.05 (.002) 10,000 50,000 270 C0402C271J5GAC 50 ±5% 0.5 (.020) ± 0.05 (.002) 10,000 50,000 330 C0402C331J5GAC 50 ±5% 0.5 (.020) ± 0.05 (.002) 10,000 50,000 F-9080A 03/06 Capacitor Ordering Information C 0402 C 331 J 5 G A C End Metallization C = Standard (Tin-plate nickel barrier) Style C - Ceramic Size Code See dimension table Failure Rate Level A = Not Applicable Specification C - Standard Capacitance Code, pF First two digits represent significant figures. Third digit specifies number of zeros. 100 pF = 101. (Use “9” for 1.0 through 9.9 pF) (Use “8” for 0.1 through .99 pF) Temperature Characteristic Designated by Capacitance Change Over Temperature Range G = C0G (0±30 ppm/°C) (-55°C +125°C) Capacitance Tolerance J = ± 5% Voltage 5 = 50V Electrical Parameters As detailed in the KEMET Surface Mount Catalog F3102 for C0G, with following specific requirements based on room temperature (25°C) parameters: • Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 30 ppm/°C over that range. • Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 10,000 MΩ, minimum. • Capacitance and Quality Factor (Q) measured at 1 MHz and 0.5 Vrms: DF limit is 0.1% Q = (< 30 pF: Q ≥ 400 + 20C; > 30pF: Q ≥ 1000) C = Nominal Capacitance Soldering Process These components are suitable for reflow only. All parts incorporate the standard KEMET barrier layer of pure nickel, with an overplate of pure tin to provide excellent solderability as well as resistance to leaching. Marking These chips will be supplied unmarked. In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors. The information in this bulletin supplements that in the catalog. F-9080A 03/06 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com