D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply PRODUCT OVERVIEW The D1U4CS-W-2200-12-HxxC is a 2200 Watt, power-factor-corrected (PFC) front-end power supply for hotswapping redundant systems. The main output is 12V with standby output of 5V or 3.3V. Packaged in 1U low profile, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power architecture systems requiring high power density. The highly efficient electrical and thermal design with internal cooling fans supports reliable operation conditions. The D1U4CS-W-2200-12-HxxC is designed to auto-recover from overtemperature fault. Status information is provided with front panel LEDs, logic signals and I2C management interface. Four units can be packaged into an optional 19” 1U power shelf to provide up to 8.8kW of power. SELECTION GUIDE Model Number FEATURES 2200W (220Vac), 1100W (110Vac) Output Power Certified to Climate Savers Computing InitiativeSM and 80 PLUS® Gold efficiency D1U4CS-W-2200-12-HC4C D1U4CS-W-2200-12-HC3C D1U4CS-W-2200-12-HA4C D1U4CS-W-2200-12-HA3C Power Output High Line AC Power Output Low Line AC Main Output Standby Output Airflow 2200W 2200W 2200W 2200W 1100W 1100W 1100W 1100W 12.12V 12.12V 12.12V 12.12V 3.3V 3.3V 5V 5V Back to front Front to back Back to front Front to back INPUT CHARACTERISTICS Parameter Conditions Min. 12V Main Output, 3.3V or 5V Standby Output Input Voltage Operating Range Low Line AC High Line AC 1U sized; dimensions 14.0” x 4.0” x 1.6” Input Frequency Turn-on Input Voltage Turn-off Input Voltage 90 180 47 81 70.5 24.5 Watts per cubic inch density N+1 redundancy capable, including hot-docking Active Current Sharing on main output Over-voltage, Over-current, Over-temperature protection Internal cooling fans (variable speed) I²C Bus Interface, PSMI compliant Maximum Input Current Inrush Current Power Factor 60 Max. 140 264 63 89 78 13 13 16.5 Units Vac Hz Vac Arms Apk 0.95 0.95 OUTPUT VOLTAGE CHARACTERISTICS Output Voltage RoHS compliant Optional 1U x 19” Power-Shelf Ramp up Ramp down Low Line AC 90Vac High Line AC 180Vac Cold start between 0-1msec Output load >90% Output load >50% Typ. 12V 5Vsb 3.3Vsb Parameter Voltage Set Point Accuracy Line and Load Regulation Ripple Voltage & Noise Output Current Load Capacitance Voltage Set Point Accuracy Line and Load Regulation Ripple Voltage & Noise Operating Range Load Capacitance Voltage Set Point Accuracy Line and Load Regulation Ripple Voltage & Noise Operating Range Load Capacitance Conditions Min. Typ. Max. 12.12 11.76 12.48 120 180 30000 20MHz Bandwidth 0 5 20MHz Bandwidth 4.85 5.15 50 5 10000 0 3.3 20MHz Bandwidth 3.2 0 3.4 50 6 10000 Units Vdc mV p-p A μF Vdc mV p-p A μF Vdc mV p-p A μF 1 Ripple and noise are measured with 0.1 uF of ceramic capacitance and 10 uF of tantalum capacitance on each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used. For full details go to www.murata-ps.com/rohs www.murata-ps.com email: [email protected] 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 1 of 5 D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply OUTPUT CHARACTERISTICS Parameter Conditions Min. Remote Sense Efficiency (80+ measurement; excludes fan load) Output Rise Monotonicity Start-up Time Transient Response Typ. Max. Units 120 mV 20% and full load 89.10 50% load 93.04 Overshoot less than 10% for all outputs, no voltage negative between 10% to 95% during ramp up AC ramp up 1.5 PS_On activated 150 12V Ramp 1A/μs ±360 5Vsb Ramp 1A/μs ±150 3.3Vsb Ramp 1A/μs ±100 Current sharing accuracy (up to 3 in parallel) At 100% load Hot Swap Transients Hold-up Time All outputs within regulation 100% load % s ms mV ±7 % 5 % ms Max. Units 12 GENERAL CHARACTERISTICS Parameter Conditions Storage Temperature Range Non-condensing Operating Temperature Range Operating Humidity Storage Humidity Shock Sinusoidal Vibration MTBF Acoustic Safety Approvals Input Fuse Material Flammability Switching Frequency Weight Min. Typ. -40 70 D1U4CS-W-2200-12-HC4C and D1U4CS-W-2200-12-HA4C models only 0 50 D1U4CS-W-2200-12-HC3C and D1U4CS-W-2200-12-HA3C models only 0 40 10 5 90 90 Non-condensing 30G non operating 0.5G, 5 – 500 Hz operating Calculated per Bellcore at Ta=30°C 400 Demonstrated 400 ISO 7779-1999 c-CSA-us (CSA 60950-1-03/UL 60950-1, Second Edition) Power Supply has internal 20A/250V fast blow fuse on the AC line input UL 94V-0 TBD 2.1kg 60 °C % Khrs Khrs dB LpAm PROTECTION CHARACTERISTICS Output Voltage 12V 5Vsb 3.3Vsb Parameter Conditions Min. Over-temperature Over Voltage Over Current Over Voltage Over Current Over Voltage Over Current Auto-restart Latching Latching Latching Brick wall, autorecovery Latching Brick wall, autorecovery 55 13.12 197 5.6 5.5 3.57 6.5 www.murata-ps.com Typ. Max. Units 65 14.12 225 6.26 6.25 4.02 8.0 °C V A V A V A email: [email protected] 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 2 of 5 D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply ISOLATION CHARACTERISTICS Parameter Insulation Safety Rating / Test Voltage Isolation Material Flammability Grounding Conditions Min. Typ. Max. Units Input to Output - Reinforced 3000 Vrms Input to Chassis - Basic 1500 Vrms Output to Chassis Output to Output UL 94V-0 Main Output Return and Standby Output Return are connected internally. 100kΩ resistor parallel with 100nF capacitor is connected between Return and power supply chassis. Main Output Return should be connected to the System Chassis CONTROL SIGNALS Status LED I2C Registers Conditions Off Flashing Green Green Refer to Application Note #ACAN-33 Description No AC input to all PS Main Output Absent Power Supply Good EMISSIONS AND IMMUNITY Characteristic Description Harmonics Voltage Fluctuation and Flicker Emission Conducted Emission Radiated IEC/EN 61000-3-2 IEC/EN 61000-3-3 FCC 47 CFR Parts 15/CISPR 22/EN55022 FCC 47 CFR Parts 15/CISPR 22/EN55022 ESD IEC/EN 61000-4-2 Electromagnetic Field Electrical Fast Transients/Burst Surge RF Conducted Immunity Magnetic Immunity Voltage dips, interruptions IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 IEC/EN 61000-4-11 Criteria Class A, 6dB margin Class A, 6dB margin 4kV contact discharge 8kV operational air discharge 15kV non-operational air discharge 1kV/2kV, Performance Criteria A 3 Vac, 80% AM, 1kHz, Performance Criteria A 3 A/m www.murata-ps.com email: [email protected] 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 3 of 5 D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply OUTPUT CONNECTOR AND SIGNAL SPECIFICATION DC and Signal Connector: FCI PowerBlade # 51732-048LF P1 VOUT P2 VOUT P3 VOUT P4 VOUT P5 VOUT P6 P7 VRTN VRTN P8 VRTN P9 VRTN P10 x1 x2 x3 x4 x5 x6 AC_OK/H PW_OK/H Vsb RETURN Vsb RETURN Vsb +OUT Vsb +OUT D SPARE SMB/ Alert Vsb RETURN Vsb RETURN Vsb +OUT Vsb +OUT C I_SHARE I2C ADR0 I2C ADR1 I2C ADR2 PS_KILL PS_ PRESENT B SENSE + SENSE - I2C DATA I2C CLOCK SPARE PS_ON/L A VRTN mate-last pins High Level Low Level Pin Assignment Signal Name Description I Max P1 to P5 P6 to P10 VOUT VRTN Main output voltage Main output voltage, return A1 Sense + VOUT remote sense, positive node input, connected to the +ve load point A2 Sense - VOUT remote sense, negative node input, connected to the -ve load point C5, C6, D5, D6 C3, C4, D3, D4 B1 Vsb Vsb Return I_Share Standby voltage output Standby voltage, return, tied internally to Output Return Active load sharing bus 0 – 8V -4 mA / +5 mA D1 AC_OK/H Input AC Voltage “OK” signal output (Internal pull up is 10kΩ to 3.3V) >2.1V <0.8V +4 mA -2 mA D2 PW_OK/H Internal pull up of 10K ohm to 3.3V >2.1V <0.8V +4 mA -2 mA C2 SMB/Alert SMB/Alert signal output (open collector) B5 PS_Kill Floating pin will turn off P/S (shorter pin, last-make and first-break contact for hot plugging). This signal overrides PS-On in disabling the Main Output >2.1V (open) <0.8V (active, PS:On) N/A B6 PS_Present Internally tied to 3.3V return 0V A6 PS_On/L Internal 3.3K ohm pull-up to 3.3V, (accepts open collector/ drain drive), This signal to be pulled low to turn-on power supply >2.1V (open, or 3.3V) <0.8V (active, PS:On) A3 A4 I2C Data I2C Clock I2C serial data bus; internal 4.64K ohm pull-up I2C serial clock bus; internal 4.64K ohm pull-up 3.3V 3.3V B2 I2C Adr0 Address input 0, internal 10K ohm pull-up to 3.3V >2.1V <0.8V ±1 mA B3 I2C Adr1 Address input 1, internal 10K ohm pull-up to 3.3V >2.1V <0.8V ±1 mA B4 I2C Adr2 Address input 2, internal 10K ohm pull-up to 3.3V >2.1V <0.8V ±1 mA D1U4CS MATING CONNECTORS 12V D1U4 mating connector Solder 1 Press Fit Straight Murata-PS FCI N/A N/A Right Angle 4321-01454-0 51762-11002400ABLF Straight N/A N/A Right Angle N/A N/A 1 Solder connector recommended for board thickness of <0.090 www.murata-ps.com email: [email protected] 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 4 of 5 D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply MECHANICAL DIMENSIONS - D1U4CS-W-2200-12-HxxC 41.00 ±0.40 1.614 ±0.016 Airflow Front to Back 101.60 ±0.50 4.000 ±0.020 349.60 ±0.40 13.764 ±0.016 12.63 ±0.40 0.497 ±0.016 2.40 ±0.25 0.094 ±0.010 7.62 ±0.40 0.300 ±0.016 Airflow Back to Front 8.89 ±0.25 0.350 ±0.010 AC Input Connector: The AC input connector is standard IEC C20 20A. 355.60 ±0.65 14.000 ±0.026 Dimensions: 13.76”L x 4.00” W x 1.61” H OPTIONAL ACCESSORIES Description Part Number 12V D1U4CS output connector card D1U4CS-12-CONC APPLICATION NOTES Document Number Description ACAN-32 Output Connector Card for D1U4CS ACAN-33 D1U4CS Communication Protocol Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2010 Murata Power Solutions, Inc. www.murata-ps.com/locations email: [email protected] 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 5 of 5