VISHAY SI1410EDH

Si1410EDH
Vishay Siliconix
N-Channel 20 V (D-S) MOSFET
FEATURES
PRODUCT SUMMARY
VDS (V)
20
RDS(on) (Ω)
ID (A)
0.070 at VGS = 4.5 V
3.7
0.080 at VGS = 2.5 V
3.4
0.100 at VGS = 1.8 V
3.0
• Halogen-free According to IEC 61249-2-21
Definition
• TrenchFET® Power MOSFETs: 1.8 V Rated
• ESD Protected: 2000 V
• Thermally Enhanced SC-70 Package
• Compliant to RoHS Directive 2002/95/EC
APPLICATIONS
• Load Switching
• PA Switch
• Level Switch
SOT-363
SC-70 (6-LEADS)
1
6
D
D
2
5
D
G
3
4
S
Marking Code
AA
XX
1 kΩ
YY
D
D
G
Lot Traceability
and Date Code
Part # Code
Top View
S
Ordering Information: Si1410EDH-T1-E3 (Lead (Pb)-free)
Si1410EDH-T1-GE3 (Lead (Pb)-free and Halogen-free)
ABSOLUTE MAXIMUM RATINGS TA = 25 °C, unless otherwise noted
Parameter
Symbol
5s
Steady State
Drain-Source Voltage
VDS
20
Gate-Source Voltage
VGS
± 12
Continuous Drain Current (TJ = 150 °C)a
TA = 25 °C
TA = 85 °C
Pulsed Drain Current
IS
TA = 25 °C
TA = 85 °C
Operating Junction and Storage Temperature Range
PD
V
3.7
2.9
2.6
2.0
IDM
Continuous Diode Current (Diode Conduction)a
Maximum Power Dissipationa
ID
8
1.4
A
0.9
1.56
1.0
0.81
0.52
TJ, Tstg
Unit
- 55 to 150
W
°C
THERMAL RESISTANCE RATINGS
Parameter
Maximum Junction-to-Ambienta
Maximum Junction-to-Foot (Drain)
Symbol
t≤5s
Steady State
Steady State
RthJA
RthJF
Typical
Maximum
60
80
100
125
34
45
Unit
°C/W
Notes:
a. Surface mounted on 1" x 1" FR4 board.
Document Number: 71409
S10-0935-Rev. B, 19-Apr-10
www.vishay.com
1
Si1410EDH
Vishay Siliconix
SPECIFICATIONS TJ = 25 °C, unless otherwise noted
Parameter
Symbol
Test Conditions
Min.
VDS = VGS, ID = 250 µA
0.45
Typ.
Max.
Unit
VDS = 0 V, VGS = ± 4.5 V
±1
µA
VDS = 0 V, VGS = ± 12 V
± 10
mA
VDS = 16 V, VGS = 0 V
1
VDS = 16 V, VGS = 0 V, TJ = 85 °C
5
Static
Gate Threshold Voltage
VGS(th)
Gate-Body Leakage
IGSS
Zero Gate Voltage Drain Current
IDSS
On-State Drain Currenta
ID(on)
Drain-Source On-State Resistancea
VDS = 5 V, VGS = 4.5 V
RDS(on)
Forward Transconductancea
Diode Forward Voltagea
V
µA
4
A
VGS = 4.5 V, ID = 3.7 A
0.055
0.070
VGS = 2.5 V, ID = 3.4 A
0.065
0.080
VGS = 1.8 V, ID = 1.7 A
0.080
0.100
gfs
VDS = 10 V, ID = 3.7 A
10
VSD
IS = 1.4 A, VGS = 0 V
0.75
1.1
5.6
8
VDS = 10 V, VGS = 4.5 V, ID = 3.7 A
0.75
Ω
S
V
Dynamicb
Total Gate Charge
Qg
Gate-Source Charge
Qgs
nC
Gate-Drain Charge
Qgd
1.10
Turn-On Delay Time
td(on)
0.15
0.25
0.4
0.6
1.9
2.8
1.2
1.8
Rise Time
VDD = 10 V, RL = 10 Ω
ID ≅ 1 A, VGEN = 4.5 V, Rg = 6 Ω
tr
Turn-Off Delay Time
td(off)
Fall Time
tf
µs
Notes:
a. Pulse test; pulse width ≤ 300 µs, duty cycle ≤ 2 %.
b. Guaranteed by design, not subject to production testing.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
10 000
10
1000
IGSS - Gate Current (µA)
IGSS - Gate Current (mA)
8
6
4
100
10
TJ = 150 °C
1
TJ = 25 °C
2
0.1
0
0.01
0
www.vishay.com
2
3
6
9
12
15
18
0
3
6
9
VGS - Gate-to-Source Voltage (V)
VGS - Gate-to-Source Voltage (V)
Gate-Current vs. Gate-Source Voltage
Gate-Current vs. Gate-Source Voltage
12
Document Number: 71409
S10-0935-Rev. B, 19-Apr-10
Si1410EDH
Vishay Siliconix
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
8
8
25 °C
VGS = 5 V thru 2 V
6
ID - Drain Current (A)
ID - Drain Current (A)
6
1.5 V
4
2
TC = - 55 °C
125 °C
4
2
1V
0
1
2
3
4
0
0.00
5
0.50
0.75
1.00
1.25
1.50
VGS - Gate-to-Source Voltage (V)
Output Characteristics
Transfer Characteristics
0.15
1000
0.12
800
0.09
0.25
VDS - Drain-to-Source Voltage (V)
C - Capacitance (pF)
RDS(on) - On-Resistance (Ω)
0
VGS = 1.8 V
VGS = 2.5 V
0.06
VGS = 4.5 V
0.03
600
1.75
2.00
Ciss
400
200
Coss
0.00
0.0
1.5
3.0
4.5
6.0
7.5
0
12
16
VDS - Drain-to-Source Voltage (V)
Capacitance
20
1.8
VDS = 10 V
ID = 3.7 A
1.6
RDS(on) - On-Resistance
(Normalized)
VGS - Gate-to-Source Voltage (V)
8
ID - Drain Current (A)
3
2
1
0
0.0
4
On-Resistance vs. Drain Current
5
4
Crss
0
VGS = 4.5 V
ID = 3.7 A
1.4
1.2
1.0
0.8
1.5
3.0
4.5
6.0
7.5
0.6
- 50
- 25
0
25
50
75
100
125
Qg - Total Gate Charge (nC)
TJ - Junction Temperature (°C)
Gate Charge
On-Resistance vs. Junction Temperature
Document Number: 71409
S10-0935-Rev. B, 19-Apr-10
150
www.vishay.com
3
Si1410EDH
Vishay Siliconix
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
0.25
RDS(on) - On-Resistance (Ω)
IS - Source Current (A)
10
TJ = 25 °C
TJ = 150 °C
1
0.15
ID = 3.7 A
0.10
0.05
0.00
0.1
0
0.3
0.6
0.9
1.2
0
1.5
1
2
3
4
5
6
VSD - Source-to-Drain Voltage (V)
VGS - Gate-to-Source Voltage (V)
Source-Drain Diode Forward Voltage
On-Resistance vs. Gate-to-Source Voltage
0.2
35
0.1
ID = 250 µA
28
0.0
Power (W)
VGS(th) - Variance (V)
0.20
- 0.1
21
14
- 0.2
7
- 0.3
- 0.4
- 50
- 25
0
25
50
75
100
125
150
0
0.001
0.01
0.1
1
10
TJ - Junction Temperature (°C)
Time (s)
Threshold Voltage
Single Pulse Power, Junction-to-Ambient
2
Normalized Effective Transient
Thermal Impedance
1
Duty Cycle = 0.5
0.2
Notes:
0.1
PDM
0.1
0.05
t1
t2
1. Duty Cycle, D =
0.02
t1
t2
2. Per Unit Base = RthJA = 100 °C/W
Single Pulse
3. TJM - TA = PDMZthJA(t)
4. Surface Mounted
0.01
10-4
10-3
10-2
10-1
1
Square Wave Pulse Duration (s)
10
100
600
Normalized Thermal Transient Impedance, Junction-to-Ambient
www.vishay.com
4
Document Number: 71409
S10-0935-Rev. B, 19-Apr-10
Si1410EDH
Vishay Siliconix
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
2
Normalized Effective Transient
Thermal Impedance
1
Duty Cycle = 0.5
0.2
0.1
0.1
0.05
0.02
Single Pulse
0.01
10-4
10-3
10-2
10-1
Square Wave Pulse Duration (s)
1
10
Normalized Thermal Transient Impedance, Junction-to-Foot
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?71409.
Document Number: 71409
S10-0935-Rev. B, 19-Apr-10
www.vishay.com
5
Package Information
Vishay Siliconix
SCĆ70:
6ĆLEADS
MILLIMETERS
6
5
Dim
A
A1
A2
b
c
D
E
E1
e
e1
L
4
E1 E
1
2
3
-B-
e
b
e1
D
-Ac
A2 A
L
A1
Document Number: 71154
06-Jul-01
INCHES
Min
Nom
Max
Min
Nom
Max
0.90
–
1.10
0.035
–
0.043
–
–
0.10
–
–
0.004
0.80
–
1.00
0.031
–
0.039
0.15
–
0.30
0.006
–
0.012
0.10
–
0.25
0.004
–
0.010
1.80
2.00
2.20
0.071
0.079
0.087
1.80
2.10
2.40
0.071
0.083
0.094
1.15
1.25
1.35
0.045
0.049
0.053
0.65BSC
0.026BSC
1.20
1.30
1.40
0.047
0.051
0.055
0.10
0.20
0.30
0.004
0.008
0.012
7_Nom
7_Nom
ECN: S-03946—Rev. B, 09-Jul-01
DWG: 5550
www.vishay.com
1
AN815
Vishay Siliconix
Single-Channel LITTLE FOOTR SC-70 6-Pin MOSFET
Copper Leadframe Version
Recommended Pad Pattern and Thermal Performance
INTRODUCTION
EVALUATION BOARDS SINGLE SC70-6
The new single 6-pin SC-70 package with a copper leadframe
enables improved on-resistance values and enhanced
thermal performance as compared to the existing 3-pin and
6-pin packages with Alloy 42 leadframes. These devices are
intended for small to medium load applications where a
miniaturized package is required. Devices in this package
come in a range of on-resistance values, in n-channel and
p-channel versions. This technical note discusses pin-outs,
package outlines, pad patterns, evaluation board layout, and
thermal performance for the single-channel version.
The evaluation board (EVB) measures 0.6 inches by
0.5 inches. The copper pad traces are the same as in Figure 2.
The board allows examination from the outer pins to 6-pin DIP
connections, permitting test sockets to be used in evaluation
testing. See Figure 3.
52 (mil)
BASIC PAD PATTERNS
See Application Note 826, Recommended Minimum Pad
Patterns With Outline Drawing Access for Vishay Siliconix
MOSFETs, (http://www.vishay.com/doc?72286) for the basic
pad layout and dimensions. These pad patterns are sufficient
for the low to medium power applications for which this
package is intended. Increasing the drain pad pattern yields a
reduction in thermal resistance and is a preferred footprint.
The availability of four drain leads rather than the traditional
single drain lead allows a better thermal path from the package
to the PCB and external environment.
96 (mil)
6
5
4
1
2
3
71 (mil)
26 (mil)
13 (mil)
0, 0 (mil)
18 (mil)
26 (mil)
PIN-OUT
16 (mil)
Figure 1 shows the pin-out description and Pin 1
identification.The pin-out of this device allows the use of four
pins as drain leads, which helps to reduce on-resistance and
junction-to-ambient thermal resistance.
SOT-363
SC-70 (6-LEADS)
D
1
6
D
D
2
5
D
G
3
4
S
FIGURE 2.
SC-70 (6 leads) Single
The thermal performance of the single 6-pin SC-70 has been
measured on the EVB, comparing both the copper and
Alloy 42 leadframes. This test was first conducted on the
traditional Alloy 42 leadframe and was then repeated using the
1-inch2 PCB with dual-side copper coating.
Top View
FIGURE 1.
For package dimensions see outline drawing SC-70 (6-Leads)
(http://www.vishay.com/doc?71154)
Document Number: 71334
12-Dec-03
www.vishay.com
1
AN815
Vishay Siliconix
Front of Board SC70-6
Back of Board SC70-6
vishay.com
FIGURE 3.
THERMAL PERFORMANCE
Junction-to-Foot Thermal Resistance
(Package Performance)
COOPER LEADFRAME
Room Ambient 25 _C
The junction to foot thermal resistance is a useful method of
comparing different packages thermal performance.
A helpful way of presenting the thermal performance of the
6-Pin SC-70 copper leadframe device is to compare it to the
traditional Alloy 42 version.
Thermal performance for the 6-pin SC-70 measured as
junction-to-foot thermal resistance, where the “foot” is the
drain lead of the device at the bottom where it meets the PCB.
The junction-to-foot thermal resistance is typically 40_C/W in
the copper leadframe and 163_C/W in the Alloy 42 leadframe
— a four-fold improvement. This improved performance is
obtained by the enhanced thermal conductivity of copper over
Alloy 42.
The typical RqJA for the single 6-pin SC-70 with copper
leadframe is 103_C/W steady-state, compared with 212_C/W
for the Alloy 42 version. The figures are based on the 1-inch2
FR4 test board. The following example shows how the thermal
resistance impacts power dissipation for the two different
leadframes at varying ambient temperatures.
ALLOY 42 LEADFRAME
PD +
Rq JA
Elevated Ambient 60 _C
PD +
T J(max) * T A
Rq JA
o
o
P D + 150 Co* 25 C
212 CńW
o
o
P D + 150 Co* 25 C
212 CńW
P D + 590 mW
P D + 425 mW
www.vishay.com
2
T J(max) * T A
T J(max) * T A
Rq JA
PD +
T J(max) * T A
Rq JA
o
o
P D + 150 Co* 25 C
124 CńW
o
o
P D + 150 Co* 60 C
124 CńW
P D + 1.01 W
P D + 726 mW
As can be seen from the calculations above, the compact 6-pin
SC-70 copper leadframe LITTLE FOOT power MOSFET can
handle up to 1 W under the stated conditions.
Testing
To further aid comparison of copper and Alloy 42 leadframes,
Figure 5 illustrates single-channel 6-pin SC-70 thermal
performance on two different board sizes and two different pad
patterns. The measured steady-state values of RqJA for the
two leadframes are as follows:
LITTLE FOOT 6-PIN SC-70
Power Dissipation
Room Ambient 25 _C
PD +
Elevated Ambient 60 _C
1) Minimum recommended pad pattern on
the EVB board V (see Figure 3.
1-inch2
2) Industry standard
PCB with
maximum copper both sides.
Alloy 42
Copper
329.7_C/W
208.5_C/W
211.8_C/W
103.5_C/W
The results indicate that designers can reduce thermal
resistance (RqJA) by 36% simply by using the copper
leadframe device rather than the Alloy 42 version. In this
example, a 121_C/W reduction was achieved without an
increase in board area. If increasing in board size is feasible,
a further 105_C/W reduction could be obtained by utilizing a
1-inch2 square PCB area.
The copper leadframe versions have the following suffix:
Single:
Si14xxEDH
Dual:
Si19xxEDH
Complementary: Si15xxEDH
Document Number: 71334
12-Dec-03
AN815
400
250
320
200
240
Thermal Resistance (C/W)
Thermal Resistance (C/W)
Vishay Siliconix
Alloy
42
160
Copper
80
150
Alloy
42
100
50
Copper
0
0
10-5
10-4
10-3
10-2
10-1
1
10
100
1000
10-5
Leadframe Comparison on EVB
Document Number: 71334
12-Dec-03
10-3
10-2
10-1
1
10
100
1000
Time (Secs)
Time (Secs)
FIGURE 4.
10-4
FIGURE 5.
Leadframe Comparison on Alloy 42 1-inch2 PCB
www.vishay.com
3
Application Note 826
Vishay Siliconix
RECOMMENDED MINIMUM PADS FOR SC-70: 6-Lead
0.067
0.026
(0.648)
0.045
(1.143)
0.096
(2.438)
(1.702)
0.016
0.026
0.010
(0.406)
(0.648)
(0.241)
Recommended Minimum Pads
Dimensions in Inches/(mm)
Return to Index
APPLICATION NOTE
Return to Index
www.vishay.com
18
Document Number: 72602
Revision: 21-Jan-08
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1