TOSHIBA TLP2116

TLP2116
TOSHIBA PHOTOCOUPLER
GaAℓAs Ired & PHOTO-IC
TLP2116
○ Plasma Display Panels (PDP)
○ High-Speed Interfaces
○ Factory Automation (FA)
Unit: mm
7
6
5
1
2
3
4
3.95 ± 0.25
8
The TOSHIBA TLP2116 dual photocoupler consists of a pair of GaAℓAs
light-emitting diodes optically coupled to integrated high gain and high-speed
photodetectors.
5.1 ± 0.2
Inverter logic (totem-pole output)
z
Package: SO-8
z
Guaranteed performance over temperature : -40 to 100°C
z
Power supply voltage: 4.5 to 5.5 V
z
Input thresholds current: IFHL = 5 mA (max)
z
Propagation delay time (tpHL/tpLH): 75 ns (max)
z
Switching speed: 15 MBd (typ.)(NRZ)
z
Common mode transient immunity: ±10 kV/μs
z
Isolation voltage: 2500 Vrms
6.0 ± 0.2
1.27 ± 0.15
0.38
0.1 ± 0.1 2.5 ± 0.2
z
0.305 min
11-5K1
JEDEC
―
JEITA
―
TOSHIBA
11−5K1
Weight: 0.21g (typ.)
Truth Table
Input
H
L
LED1(2)
ON
OFF
Tr1(3)
OFF
ON
Tr2(4)
ON
OFF
Output 1(2)
L
H
Pin Configuration (Top View)
Schematic
ICC
VCC
IF1
Tr1
1＋
I O1
2－
1
8
7
VCC
2
3
VO1
Tr2
4
GND
SHIELD
8 1:ANODE 1
2:CATHODE 1
3:CATHODE 2
7 4:ANODE 2
5:GND
6 6:VO2(Output2)
7:VO1(Output1)
5 8:VCC
SHIELD
Tr3
3－
I O2
VF2
4＋
Tr4
IF2
SHIELD
6
VO2
5
GND
A bypass capacitor of 0.1 μF must be
connected between pins 8 and 5.
1
2008-06-11
TLP2116
Absolute Maximum Ratings (Ta=25°C)
Characteristic
Symbol
DETECTOR
LED
Forward current
(Each Channel)
(Ta ≥ 85°C) (Each Channel)
Forward current derating
Peak transient forward current
Rating
Unit
IF
20
mA
⊿IF/⊿Ta
-0.5
mA/°C
IFPT
1
A
(Each Channel) (Note 2)
Reverse voltage
(Each Channel)
VR
5
V
Output current
(Each Channel)
IO
10
mA
Output voltage
(Each Channel)
VO
6
V
Supply voltage
VCC
6
V
Output power dissipation
PO
40
mW
Operating temperature range
Topr
-40 to 100
°C
Storage temperature range
Tstg
-55 to 125
°C
Lead solder temperature
Isolation voltage (AC,1min., R.H. ≤ 60%, Ta=25℃)
(10 s)
Tsol
260
°C
(Note 2)
BVS
2500
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width PW ≤ 1 μs, 300pps.
Note 2: This device is regarded as a two terminal device : pins 1, 2, 3 and 4 are shorted together,
as are pins 5, 6, 7 and 8.
Recommended Operating Conditions
Characteristic
Symbol
Min
Typ.
Max
Unit
8
－
18
mA
Input current , ON
(Each Channel)
IF(ON)
Input voltage , OFF
(Each Channel)
VF(OFF)
0
－
0.8
V
VCC
4.5
5.0
5.5
V
Topr
-40
－
100
°C
Supply voltage(*)
Operating temperature
(Note 3)
(*) This item denotes operating ranges, not meaning of recommended operating conditions.
Note 3: The detector of this product requires a power supply voltage (VCC) of 4.5 V or higher for stable operation.
If the VCC is lower than this value, an ICCH may increase, or an output may be unstable.
Be sure to use the product after checking the supply current, and the operation of a power-on/-off.
Note 4: A ceramic capacitor (0.1 μF) should be connected from pin 8 (VCC) to pin 5 (GND) to stabilize the operation
of the high gain linear amplifier. Failure to provide the bypass may impair the switching property.
The total lead length between capacitor and coupler should not exceed 1 cm.
2
2008-06-11
TLP2116
Electrical Characteristics
(Unless otherwise specified, Ta = -40 to 100℃, VCC = 4.5 to 5.5V)
Characteristic
Min
Typ.
Max
Unit
1.3
1.65
1.75
V
(Each Channel) ⊿VF/⊿Ta IF = 10 mA
－
-2.0
－
mV/°C
Input reverse current
(Each Channel)
IR
VR = 5 V, Ta = 25°C
－
－
10
μA
Input capacitance
(Each Channel)
CT
V = 0, f = 1 MHz, Ta = 25°C
－
45
－
pF
Logic low output voltage
(Each Channel)
VOL
－
－
0.4
V
Logic high output voltage
(Each Channel)
VOH
4.0
－
－
V
－
－
10.0
mA
－
－
10.0
mA
Input forward voltage
Temperature coefficient
of forward voltage
Symbol
(Each Channel)
VF
Conditions
IF = 10 mA, Ta = 25°C
IOL = 1.6 mA, IF = 12 mA,
VCC = 5 V
IOH = -0.02 mA, VF = 1.05 V
VCC = 5 V
Logic low supply current
ICCL
IF = 12 mA
Logic high supply current
ICCH
VF = 0 V
(Each Channel)
IFHL
IO =1.6 mA, VO < 0.4 V
－
－
5
mA
(Each Channel)
VFLH
IO = -0.02 mA, VO > 4.0 V
0.8
－
－
V
Input current logic low
output
Input voltage logic high
output
(Note 3)
*All typical values are at Ta=25°C, VCC=5 V unless otherwise specified
Isolation Characteristics (Ta = 25℃)
Characteristic
Capacitance input to output
Isolation resistance
Symbol
CS
RS
Test Conditions
VS = 0, f = 1 MHz
R.H. ≤ 60%, VS = 500 V
AC, 1 minute
Isolation voltage
BVS
(Note 2)
Min
Typ.
Max
Unit
―
0.8
―
pF
―
Ω
12
(Note 2) 1×10
10
14
2500
―
―
AC, 1 second, in oil
―
5000
―
DC, 1 minute, in oil
―
5000
―
3
Vrms
Vdc
2008-06-11
TLP2116
Switching Characteristics
(Unless otherwise specified, Ta = -40 to 100℃, VCC = 4.5 to 5.5V)(Each Channel)
Characteristic
Propagation delay time
to logic low output
Propagation delay time
to logic high output
Propagation delay time
to logic low output
Propagation delay time
to logic high output
Symbol
tpHL
2
tpLH
tpLH|
Common mode transient
immunity at high level output
Common mode transient
immunity at low level output
tf
Max
Unit
－
－
75
ns
(Note 5)
－
－
75
ns
RIN = 430 Ω
CIN = 27 pF
CL = 15 pF
(Note 5)
－
－
75
ns
－
－
75
ns
－
－
30
ns
—
15
—
ns
—
15
—
ns
10000
－
－
V/μs
-10000
－
－
V/μs
RIN = 100 Ω
VIN = 0→5 V
(IF = 0→8 mA)
VIN = 5→0 V
(IF = 8→0 mA)
IF = 12 mA RIN =100 Ω,
CL =15 pF
(Note 5)
1
IF = 0→12 mA
RIN =100 Ω
CL =15 pF
tr
IF = 12→0 mA
(Note 5)
VCM =1000 Vp-p , IF = 0 mA,
CMH
3
CML
Typ.
IF = 12→0 mA
tpLH
between ON and OFF
Min
CL = 15 pF
1
|tpHL-
Output rise time (10 - 90%)
Conditions
IF = 0→12 mA
tpHL
Switching time dispersion
Output fall time (90 - 10%)
Test
Circuit
VO (min) = 4 V , Ta = 25°C
VCM = 1000 Vp-p , IF = 12 mA,
VO (max) = 0.4 V , Ta = 25°C
*All typical values are at Ta=25°C
Note 5: CL is approximately 15 pF which includes probe and Jig/stray wiring capacitance.
4
2008-06-11
TLP2116
Test Circuit 1: Switching Time Test Circuit
IF=12 mA (P.G)
(f=5 MHz , duty=50%,
less than tr = tf= 5 ns)
1
VCC
IF monitor
8
7
2
GND
tf
VO
tr
VOH
90%
6
4
CL = 15 pF
VO monitor
0.1 μF
3
50%
IF
VCC
5
CL = 15 pF
SHIELD
1.5 V
RIN = 100 Ω
VOL
10%
tpLH
tpHL
CL is capacitance of the probe and JIG.
(P.G) : Pulse Generator
Test Circuit 2: Switching Time Test Circuit
VIN=5V (P.G)
(f=5 MHz , duty=50%,
less than tr = tf= 5 ns)
VIN monitor
1
8
VCC
CL = 15 pF
7
2
GND
SHIELD
tf
VO
tr
VOH
90%
6
4
CIN = 27 pF
VO monitor
0.1 μF
3
50%
IF
VCC
5
CL=15pF
1.5 V
RIN=430 Ω
VOL
10%
tpLH
tpHL
CL is capacitance of the probe and JIG.
(P.G) : Pulse Generator
Test Circuit 3: Common-Mode Transient Immunity Test Circuit
90%
90%
IF
→
SW
A
B
1
VCC
2
7
3
6
4
5
GND
SHIELD
＋
VCM
8
10%
tr
tf
1000 Ｖ
10%
0.1μF
・SW B: IF=0mA
Vo
CMH
VCC
4V
VO
0.4V
CML
・SW A: IF=12mA
－
VCＭ
CMH＝
5
800(V)
tr(μs)
CML＝-
800(V)
tf(μs)
2008-06-11
TLP2116
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively “Product”) without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must
also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document,
the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the “TOSHIBA
Semiconductor Reliability Handbook” and (b) the instructions for the application that Product will be used with or for. Customers are
solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the
appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any
information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other
referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO
LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR APPLICATIONS.
• Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring
equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document.
Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or
reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious
public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used
in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling
equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric
power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this
document.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or
vapor. Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product
or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
6
2008-06-11