Ordering number: EN2665B Thick Film Hybrid IC STK4142II AF Power Amplifier (Split Power Supply) (25W + 25W min, THD = 0.4%) Features Package Dimensions • The STK4102II series (STK4142II) and STK4101V series (high-grade type) are pin-compatible in the output range of 6W to 50W and enable easy design. • Small-sized package whose pin assignment is the same as that of the STK4101II series • Built-in muting circuit to cut off various kinds of pop noise • Greatly reduced heat sink due to substrate temperature 125°C guaranteed • Excellent cost performance unit: mm 4040 [STK4142II] Specifications Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit VCC max ±39 V θj-c 2.6 °C/W Junction Temperature Tj 150 °C Operating substrate temperature Tc 125 °C −30 to +125 °C 2 s Maximum supply voltage Thermal resistance Storage temperature Tstg Available time for load short-circuit ts VCC = ±26V, RL = 8Ω, f = 50Hz, Po = 25W Recommended Operating Conditions at Ta = 25°C Parameter Symbol Conditions Ratings Unit Recommended supply voltage VCC ±26 V Load resistance RL 8 Ω SANYO Electric Co., Ltd. Semiconductor Business Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 70397HA (ID) / O138YT / 9068MO, TS No. 2665—1/8 STK4142II Operating Characteristics at Ta = 25°C, VCC = ±26V, RL = 8Ω, Rg = 600Ω, VG = 40dB, RL : non-inductive load Parameter Quiescent current Symbol Frequency response Input impedance max Unit 100 mA 20 Po (1) 25 W Po (2) VCC = ±22V, THD = 1.0%, RL = 4Ω, f = 1kHz 25 W THD Po = 1.0W, f = 1kHz fL, fH +0 Po = 1.0W, dB –3 ri Neutral voltage VN VCC = ±31V Muting voltage VM 40 0.3 Po = 1.0W, f = 1kHz VCC = ±31V, Rg = 10kΩ Notes. typ VCC = ±31V VNO Output noise voltage min THD = 0.4%, f = 20Hz to 20kHz Icco Output power Total harmonic distortion Conditions % 20 to 50k Hz 55 kΩ 1.2 mVrms –70 0 +70 mV –2 –5 –10 V For power supply at the time of test, use a constant-voltage power supply unless otherwise specified. For measurement of the available time for load short-circuit and output noise voltage, use the specified transformer power supply shown right. The output noise voltage is represented by the peak value on rms scale (VTVM) of average value indicating type. For AC power supply, use an AC stabilized power supply (50Hz) to eliminate the effect of flicker noise in AC primary line. Specified Transformer Power Supply (Equivalent to RP-22) Equivalent Circuit No. 2665—2/8 STK4142II Sample Application Circuit : 25W min 2-channel AF power amplifier Sample Printed Circuit Pattern for Application Circuit (Cu-foiled side) No. 2665—3/8 Output power, Po - W Total harmonic distortion, THD - % Input voltage, Vi - mV Output power, Po - W Frequency, f - Hz Neutral voltage, VN - mV Quiescent current, Icco - mA Voltage gain, VG - dB Total harmonic distortion, THD - % Output power, Po - W STK4142II Output power, Po - W Frequency, f - Hz Operating substrate temperature, Tc - °C No. 2665—4/8 Voltage gain, VG - dB IC power dissipation, Pd - W IC power dissipation, Pd - W Output power, Po - W Output power, Po - W Neutral voltage, VN - mV Quiescent current, Icco - mA STK4142II Supply voltage, VCC - V Supply voltage, VCC - V Output power, Po - W Frequency, f - Hz No. 2665—5/8 STK4142II Description of External Parts C1, C2 Input filter capacitors • A filter formed with R3 or R4 can be used to reduce noise at high frequencies. C3, C4 Input coupling capacitors • Used to block DC current. When the reactance of the capacitor increases at low frequencies, the dependence of 1/f noise on signal source resistance causes the output noise to worsen. It is better to decrease the reactance. • To reduce the pop noise at the time of application of power, it is effective to increase C3, C4 that fix the time constant on the input side and to decrease C5, C6 on the NF side. C5, C6 NF capacitors • These capacitors fix the low cutoff frequency as shown below. 1 - [Hz] f L = -------------------------2π ⋅ C5 ⋅ R5 To provide the desired voltage gain at low frequencies, it is better to increase C5. However, do not increase C5 more than needed because the pop noise level becomes higher at the time of application of power. C15 Decoupling capacitor • Used to eliminate the ripple components that mix into the input side from the power line (+VCC). C11, C12 Bootstrap capacitors • When the capacitor value is decreased, the distortion is liable to be higher at low frequencies. C9, C10 Oscillation blocking capacitors • Must be inserted as close to the IC power supply pins as possible so that the power supply impedance is decreased to operate the IC stably. • Electrolytic capacitors are recommended for C9, C10. C14 Capacitor for ripple filter • Capacitor for the TR10-used ripple filter in the IC system C7 Oscillation blocking capacitor • A polyester film capacitor, being excellent in temperature characteristic, frequency characteristic, is recommended for C7. R3, R4 Resistors for input filter R1, R2 Input bias resistors • Used to bias the input pin potential to zero. These resistors fix the input impedance practically. R5, R9 (R6, R10) These resistors fix voltage gain VG. It is recommended to use R5 (R6) = 560Ω, R9 (R10) = 56kΩ for VG = 40dB. • To adjust VG, it is desirable to change R5 (or R6). • When R5 (or R6) is changed to adjust VG, R1 (=R2) =R9 (=R10) must be set to ensure VN balance. R11, R13 (R12, R14) Bootstrap resistors • The quiescent current is set by these resistors 2.2kΩ + 2.2kΩ. It is recommended to use this resistor value. R21 Resistor for ripple filter • (Limiting resistor for predriver transistor at the time of load short) R18 Used to ensure plus/minus balance at the time of clip. R19, R20 Resistor for ripple filter • When muting TR11 is turned ON, current flows from ground to -VCC through TR 11. It is recommended to use 1kΩ (1/2W) + 1kΩ (1/2W) allowing for the power that may be dissipated on that occasion. R15, R16 Oscillation blocking resistors No. 2665—6/8 STK4142II Sample Application Circuit (protection circuit and muting circuit) Thermal Design IC Power dissipation, Pd - W IC Power dissipation, Pd - W The IC power dissipation of the STK4142II at the IC-operated mode is 37.2W max. at load resistance 8Ω and 51.8W max. at load resistance 4Ω (simultaneous drive of 2 channels) for continuous sine wave as shown in Figure 1 and 2. Output power, Po - W Figure 1. STK4142II Pd – Po (RL = 8Ω) Output power, Po - W Figure 2. STK4142II Pd – Po (RL = 4Ω) No. 2665—7/8 STK4142II In an actual application where a music signal is used, it is impractical to estimate the power dissipation based on the continuous signal as shown above, because too large a heat sink must be used. It is reasonable to estimate the power dissipation as 1/10 Po max. (EIAJ). That is, Pd = 23.6W at 8Ω, Pd = 28.2W at 4Ω Thermal resistance θc-a of a heat sink for this IC power dissipation (Pd) is fixed under conditions 1 and 2 shown below. Condition 1: Tc = Pd × θc-a + Ta ≤ 125°C............................................... (1) where Ta : Specified ambient temperature Tc : Operating substrate temperature Condition 2: Tj= Pd × (θc-a) + Pd/4 × (θc-a) + Ta ≤ 150°C .................... (2) where Tj : Junction temperature of power transistor Assuming that the power dissipation is shared equally among the four power transistors (2 channels × 2), thermal resistance θj-c is 2.6°C/W and [Example] The thermal resistance of a heat sink is obtained when the ambient temperature specified for a stereo amplifier is 50°C. Assuming VCC = ±26V, RL = 8Ω, VCC = ±22V, RL = 4Ω, RL = 8Ω : Pd1 = 23.6W at 1/10 Po max. RL = 4Ω : Pd2 = 28.2W at 1/10 Po max. The thermal resistance of a heat sink is obtained from Figure 3. RL = 8Ω : θc-a1 = 3.18°C/W RL = 4Ω : θc-a2 = 2.66°C/W Tj when a heat sink is used is obtained from (3). RL = 8Ω : Tj = 140.4°C RL = 4Ω : Tj = 143.4°C Thermal resistance of heat sink, θc-a - °C/W Pd × (θc-a + 2.6/4) + Ta ≤ 150°C........................................ (3) Thermal resistance θc-a of a heat sink must satisfy inequalities (1) and (3). Figure 3 shows the relation between Pd and θc-a given from (1) and (3) with Ta as a parameter. IC Power dissipation, Pd - W Figure 3. STK4142II θc-a – Pd ■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. ■ Anyone purchasing any products described or contained herein for an above-mentioned use shall: Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: ➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees, jointly or severally. ➀ ■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of July, 1997. Specifications and information herein are subject to change without notice. No. 2665—8/8