TOSHIBA MATSUSHITA DISPLAY TECHNOLOGY INVERTER for LTM08C351 VNL08C351-INV PRODUCT INFORMATION All information is subject to change without notice. Please read bottom notes. TENTATIVE MECHANICAL SPECIFICATIONS Item Dimensional Outline (Typ.) Applicable TFT Module Weight (approximately) Specifications 110.0(W) x 22.0(H) x 10.0(Max.)(D) mm LTM08C351(8.4 Type SVGA) 25g(Typ.) ABSOLUTE MAXIMUM RATINGS *1 Item Supply Voltage Input Voltage *2 Operating Temperature *2 Storage Temperature *2 Storage Humidity Symbol Min. Max. VIN 0 14.0 -1 VIN+1 VON/VOFF 0 50 Tstg -20 60 Top 10 90 H *1 : Do not exceed the maximum rating values under the worst probable conditions Unit V kHz °C °C %(RH) taking into account the supply voltage variation, input voltage variation, variation in part constants, ambient temperature and so on. Otherwise the inverter unit may be damaged. *2 : Wet bulb temperature should be 39°C max.,and no condensation of water. ELECTRICAL SPECIFICATION *3 Item Supply Voltage Input Current Open Output Voltage Frequency *4 Output Current Symbol VIN IIN VOPEN f Min. Typ. Max. Unit 10.8 12.0 13.2 V --550 900 mA 1400 ----Vo-p 40 45 50 kHz Volume Max. --12.0 --mA(rms) IFL Volume Min. --5.5 --mA(rms) V ON/OFF Signal Voltage VON 2.5 --VIN V VOFF ----0.7 V *3 : The characteristics without remarks are measured on condition with Vin=12V and VR-VR:short. *4 : This is the sum of two output currents. *The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba Matsushita Display Technology or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba Matsushita Display Technology or others. *The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita Display Technology before proceeding with the design of equipment incorporating this product. (1/4) 2003-02-07 (Ver.2.0) VNL08C351-INV Unit : mm DIMENSIONAL OUTLINE Standard tolerance : ±0.5 (2/4) 2003-02-07 (Ver.2.0) VNL08C351-INV SCHEMATIC DIAGRAM OF INVERTER CONNECTION (3/4) 2003-02-07 (Ver.2.0) VNL08C351-INV CONNECTOR PIN ASSIGNMENT FOR INTERFACE CN1 INPUT SIGNAL Connector : 53261-0890/JAPAN MOLEX CO., LTD. Mating Connector : 51021-0800 Terminal No. Symbol Function Supply Voltage : 12.0V(Typ.) (10.8 13.2V) VIN 1 Supply Voltage : 12.0V(Typ.) (10.8 13.2V) VIN 2 1) 3 GND 0V 1) 4 GND 0V 5 ON/OFF “H” : FL ON “L” : FL OFF 6 VR Connect the Potentiometer (50kΩ) between VR(Pin No.6) and VR(Pin No.7) 7 VR Connect the Potentiometer (50kΩ) between VR(Pin No.6) and VR(Pin No.7) Vst 8 The Warning Signal : 5V in abnormal circumstances CN2 CCFL POWER SOURCE Connector : SM04(4.0)B-BHS-1/JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Terminal No. Symbol Function VFLH1 Output Power Supply for VFLH1 (High Voltage) 1 VFLH2 Output Power Supply for VFLH2 (High Voltage) 2 2) 3 NC VFLL Output Power Supply for VFLL (Low Voltage) 4 *1 : Please connect GND pin to ground. Don’t use it as no-connect nor connection with high impedance. *2 : NC Terminal is open. (Don't use) (4/4) 2003-02-07 (Ver.2.0)