26cm COLOUR TFT-LCD MODULE (10.4 TYPE) LTM10C209H (a-Si TFT) LIQUID CRYSTAL DISPLAY DIVISION PRODUCT INFORMATION FEATURES (1) (2) (3) (4) 10.4” VGA color display with High Luminance Built in Long Life Lamps(30,000 h) Replaceable structure of lamp units Full mechanical compatible with LTM10C273 (10.4” SVGA) TENTATIVE MECHANICAL SPECIFICATIONS Item Dimensional Outline (typ.) Number of Pixels Active Area Pixel Pitch Weight (approximately) Backlight Specifications 265.0(W) x 188.8(H) x 12max(D) mm 640(W) x 480(H) pixels 211.2(W) x 158.4(H) mm 0.33(W) x 0.33(H) 605g Twin CCFLs, Sidelight type ABSOLUTE MAXIMUM RATINGS Item (VDD) (VFL) FL Driving Frequency (fFL) Input Signal Voltage (VIN) Operating Temperature Storage Temperature Storage Humidity (Max. wet bulb temperature = 39°C) Min. -0.3 0 0 -0.3 0 -20 10 Supply Voltage Max. 7.0 2.0 100 VDD+0.3 50 60 90 Unit V kV(rms) kHz V °C °C %(RH) ELECTRICAL SPECIFICATION (Ta=25°C) Item Supply Voltage (VDD) (VFL) FL Start Voltage High Level Input Voltage (VIH) Low Level Input Voltage (VIL) *1 Current Consumption (IDD) *2 (IFL) *1 *2 Power Consumption Min. 4.75 500 1500 3.5 0 --3.0 --- Typ. 5.0 550 ------125 6.0 7.2 Max. 5.25 600 1800 VDD 1.5 250 7.0 --- Unit V V(rms) V(rms) V mA mA(rms) W Remarks Ta=0°C IFL =6.0mA(rms) *1 : 8 color bars pattern *2 : Except the efficiency of FL inverter OPTICAL SPECIFICATION (Ta=25°C) Item Contrast Ratio (CR) Response Time Luminance (L) (tON) (tOFF) Min. 100 ----280 Typ. 250 ----350 Max. --50 50 --- Unit --ms ms cd/m2 Remarks IFL=6.0mA(rms) *The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba or others. *The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba before proceeding with the design of equipment incorporating this product. (1/9) 2000-06-06 (Ver.2.1) 8.0 8.0 (5.5) 7.0 (2/9) 2.5 4.5 12.0max 7.0 3.0 3.5 3.0 161.1 163.4 (Bezel Openning) 130.0 +_ 0.4 65.0 (Active/Viewing Area Center) 3.5 27.7 11.0 265.0 211.2 (Active Area) 215.2 (Viewing Area) 7 3 7 3 TENTATIVE 252.0 (255.0) 259 +_ 0.4 (262.0) 3.5 19.9 216.2 (Bezel Openning) 128.0(Active/Viewing Area Center) 3.5 3 DIMENSIONAL OUTLINE 3.5 3.5 127.0 130 +_ 0.4 188.8 4- f 3.2 LTM10C209H Unit : mm Standard tolerance : 0.5 2000-06-06 (Ver.2.1) 158.4 (Active Area) 162.4 (Viewing area) 4.0 3.0 2.5 4.0 CN1 No.1 N o. 31 10.0 Be ze l Sur fa ce P CB ; 4 mm MA X. h ei gh t com po ne nt s are p la ce d 3.0 4.0 3.0 4.0 Sectional figure of I/F Connector Us er s ide C on ne ct or CN3 I /F Co nn ne ct or 80 _+ 10 80 _+ 10 TENTATIVE 4- φ 3.6 No .2 15.0 38.0 4.0 20.0 4.0 7.7 _+ 0.5 4.0 4.0 (3/9) 4.0 Pi n N o. 1 (H igh V ol ta ge ) 3.0 DIMENSIONAL OUTLINE 4.0 Pi n No .3 (L ow V olt ag e) 3.0 3.0 LTM10C209H Unit : mm Standard tolerance : 0.5 Pi n N o. 3 Pi n No .1 (H ig h Vol ta ge ) (L ow Vo lt ag e) CN2 2000-06-06 (Ver.2.1) LTM10C209H BLOCK DIAGRAM CN2 Backlight CN1 X-driver IC Panel Controller DC/DC Converter Y-driver IC Liquid Crystal Panel VBB Gray scale Manipulation Voltage Generation Circuit 640 x 480 pixels VGG CN3 Backlight (4/9) 2000-06-06 (Ver.2.1) X,1 X,2 X,3 t 3 (5/9) ENAB R5-R0 G5-G0 B5-B0 NCLK ENAB R5-R0 G5-G0 B5-B0 NCLK t6 t9 VALID DATA t8 t5 t7 X,4 X,Y t 4 t 3 X,Y t 2 t 1 640,Y VIH (MIN):3.5(V) VIL (MAX):1.5(V) Input Signal Center Level:0.5VDD 638,Y X,N t 3 639,Y X,N-1 637,Y X,N-2 VIH (MIN):3.5(V) VIL (MAX):1.5(V) 1,Y 2,Y 3,Y 4,Y 5,Y 6,Y 7,Y t c (2) Horizontal Timing R5-R0 G5-G0 B5-B0 ENAB NCLK (1) Vertical Timing NCLK b 0.5VDD Duty(a,b):50 _+ 10% a LTM10C209H TIMING CHART 2000-06-06 (Ver.2.1) LTM10C209H TIMING SPECIFICATION 1) 2) 3) 4) 5) 6) Item Frame Period Vertical Display Term One Line Scanning Time Horizontal Display Term Clock Period Clock “L” Time Clock “H” Time Set Up Time Hold Time Note 1) Symbol t1 Min. 249+N/2 x t3 300 x t3 Typ. 525 x t3 16.68 480 x t3 Max. 525 x t3 17.85 480 x t3 Unit --ms --- t2 t3 t4 684 x tc 31.5 640 x tc 800 x tc 31.78 640 x tc 860 x tc --640 x tc --µs --- tc t6 t7 t8 t9 35.0 10.0 7.0 5.0 10.0 39.72 --------- ----------- ns ns ns ns ns Remarks t2=N x t3 When ENAB is fixed to “H” level or “L” level after NCLK input, the panel is displayed as black. However, it may be occurred a flicker on the display. Note 2) When NCLK is fixed to “H” level or “L” level, the panel becomes white stage after several seconds. Note 3) Do not change t1 and t3 values in the operation. When t1 or t3 is changed, the panel is displayed as black. Note 4) Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality. There is a possibility that flicker is observed by the interference of LCD operating signal timing and FL driving condition (especially driving frequency). Note 5) When the vertical display period (N) is shorter than 480 lines, the actual display area is shifted to the center. Non-display areas become dark as follows. Note 5) The following conditions should be met. a. NCLK count of each Horizontal Scanning Time should be always the same. b. V-Blanking period should be "n" x "Horizontal Scanning Time". (n=integer) c. Frame period should be always the same. 640 pixels 1, 1 1, 2 2, 1 x, 1 640, 1 480 lines 1, y x, y 1, N 640, N (6/9) 2000-06-06 (Ver.2.1) LTM10C209H CONNECTOR PIN ASSIGNMENT FOR INTERFACE CN1 INPUT SIGNAL Connector : DF9B-31P-1V / HIROSE ELECTRIC CO., LTD. Mating Connector : DF9*-31S-1V / HIROSE ELECTRIC CO., LTD. ( * : option mark) Terminal No. Symbol Function 1 GND 2 NCLK SAMPLING CLOCK 3 GND 4 R0 RED DISPLAY DATA (LSB) 5 R1 RED DISPLAY DATA 6 R2 RED DISPLAY DATA 7 GND 8 R3 RED DISPLAY DATA 9 R4 RED DISPLAY DATA 10 R5 RED DISPLAY DATA (MSB) 11 GND 12 G0 GREEN DISPLAY DATA (LSB) 13 G1 GREEN DISPLAY DATA 14 G2 GREEN DISPLAY DATA 15 GND 16 G3 GREEN DISPLAY DATA 17 G4 GREEN DISPLAY DATA 18 G5 GREEN DISPLAY DATA (MSB) 19 GND 20 ENAB COMPOUND SYNCHRONIZATION SIGNAL 21 GND 22 B0 BLUE DISPLAY DATA (LSB) 23 B1 BLUE DISPLAY DATA 24 B2 BLUE DISPLAY DATA 25 GND 26 B3 BLUE DISPLAY DATA 27 B4 BLUE DISPLAY DATA 28 B5 BLUE DISPLAY DATA (MSB) 29 GND 30 VDD +5V POWER SUPPLY 31 VDD +5V POWER SUPPLY CN2 CCFL POWER SOURCE Connector : BHR-03VS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Mating Connector : SM02(8.0)B-BHS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Terminal No. Symbol Function 1 VFLH1 CCFL Power Supply ( high voltage) 2 NC 1) Non Connection (open) 3 VFLL1 CCFL Power Supply (low voltage) CN3 CCFL POWER SOURCE Connector : BHR-03VS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Mating Connector : SM02(8.0)B-BHS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Terminal No. Symbol Function 1 VFLH2 CCFL Power Supply ( high voltage) 2 NC 1) Non Connection (open) 3 VFLL2 CCFL Power Supply (low voltage) Note 1) NC terminal should be open. (7/9) 2000-06-06 (Ver.2.1) TM10C209H 256k (k=1024) COLORS COMBINATION TABLE Basic Color Gray Scale of Red Display Black Blue Green Light Blue Red Purple Yellow White Black Dark ↑ ↓ Light Red Black Gray Scale of Green Dark ↑ ↓ Light Green Black Gray Scale of Blue Dark ↑ ↓ Light Blue Black Gray Scale of White & Black Dark ↑ ↓ Light White R5 L L L L H H H H L L L H H H L L L R4 R3 R2 R1 R0 L L L L L L L L L L L L L L L L L L L L H H H H H H H H H H H H H H H H H H H H L L L L L L L L L H L L L H L : : H H H L L L H H H L L L H H H L L L L H H L L L H L H L L L G5 L L H H L L H H L L L L L L L L L G4 G3 G2 G1 G0 L L L L L L L L L L H H H H H H H H H H L L L L L L L L L L H H H H H H H H H H L L L L L L L L L L L L L L L : : L L L L L L L L L L L L : : L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H H H L L L H H H L L L H H H L L L H H H H H H L L L L H L L L L L L L L L L L L L L L L L L L H H H L L L L H H L L L H L H L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H L L L L H L L L L L L L L L L L L L L L L L L L L L L L L H L L L L H L H H H L L L H H H L L L H H H L L L : : H H H L H H H L H H H H H H H H H H L L L L L L L L L L L L L61 L62 Red L63 L 0 L 1 L 2 L3… L60 L L L L L L L L L L L H L L L L H L L61 L62 Green L63 L 0 L 1 L 2 L3… L60 H H H L L L L H H L L H H L H L H L L61 L62 Blue L63 L 0 L 1 L 2 L3… L60 H H H L H H H L H L61 L62 White L63 : : L L L L L L : : H H H L H H (8/9) H L H H H H H H H H H H Gray Scale Level L 0 L 1 L 2 L3… L60 L L L L L L : : : : : : H H H L L L L L H B4 B3 B2 B1 B0 L L L L L H H H H H L L L L L H H H H H L L L L L H H H H H L L L L L H H H H H L L L L L L L L L L L L L L L : : : : : : L L L L L L L L L L L L B5 L H L H L H L H L L L 2000-06-06 (Ver.2.1) LTM10C209H ! FOR SAFETY LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in Engineering Information No.EE-N001,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA LCD MODULES". Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical information. 1) SPECIAL PURPOSES A) Toshiba's Standard LCD Modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic. B) Since Toshiba's Standard LCD Modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed Toshiba's published specification limits. C) In addition, since Toshiba Standard LCD Modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems. 2) DISASSEMBLING OR MODIFICATION DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. Toshiba doses not warrant the module, if customer disassembled or modified it. 3) BREAKAGE OF LCD PANEL DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD panel is broken and liquid crystal material spills out. If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 4) GLASS OF LCD PANEL BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken. 5) ELECTRIC SHOCK DISCONNECT POWER SUPPLY before handling LCD module. DO NOT TOUCH the parts inside LCD module and the fluorescent lamp's connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. 6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be damaged. Employ protection circuit for power supply, whenever the specification or TD specifies it. Suitable protection circuit should be applied for each system design. 7) DISPOSAL When dispose LCD module, obey to the applicable environmental regulations. (9/9) 2000-06-06 (Ver.2.1)