TOSHIBA TLWD1100

TLWD1100(T11)
TOSHIBA LED Lamps
TLWD1100(T11)
Panel Circuit Indicator
•
•
•
•
•
•
•
•
•
•
Unit: mm
Surface-mount devices
3.2 (L) × 2.8 (W) × 1.9 (H) mm
LED chip + phosphor
Luminous intensity : Iv = 180 mcd (typ.) @20mA
Color: White
Chromaticity (typ.) : Cx=0.32,Cy=0.31
Topr / Tstg = -40 to 100°C
Reflow soldering is possible
Applications: automotive use,
backlighting etc.
Standard embossed tape packing: T11 (2000/reel)
8-mm tape reel
Color and Material
Product Name
Color
Material
TLWD1100
White
InGaN
Rating
Unit
IF
30
mA
Power Dissipation
PD
120
mW
Operating Temperature
Topr
−40~100
°C
Storage Temperature
Tstg
−40~100
°C
(Note 1)
JEITA
―
4-3R1
Weight: 0.035 g (typ.)
Symbol
Forward Current
―
TOSHIBA
Absolute Maximum Ratings (Ta = 25°C)
Characteristics
JEDEC
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Forward current derating
30
Allowable forward current
IF
(mA)
IF – Ta
35
25
20
15
10
5
0
0
20
40
60
80
Ambient temperature
1
Ta
100
120
(°C)
2007-10-01
TLWD1100(T11)
Electrical Characteristics (Ta = 25°C)
Characteristics
Symbol
Test condition
Min.
Typ.
Max.
Unit
Forward Voltage
VF
IF = 20 mA
2.7
3.3
4.0
V
Reverse Current
IR
VR = 4 V
⎯
⎯
10
uA
Symbol
Test condition
Min.
Typ.
Max.
Unit
Cx
IF = 20 mA
(Note 2)
⎯
Cy
IF = 20 mA
(Note 2)
⎯
IV
IF = 20 mA
Optical Characteristics (Ta = 25°C)
Characteristics
Chromaticity
Luminous Intensity
(Note 3)
63
180
320
mcd
Note 2: The product is tested at the following chromaticity coordinate groups.
Cy
Test conditions: IF=20mA, Ta=25°C
Tolerance: +/-0.01
0.42
0.41
0.40
0.39
0.38
0.37
0.36
0.35
0.34
0.33
0.32
0.31
0.30
0.29
0.28
0.27
0.26
0.25
0.24
0.23
0.22
0.21
0.20
8L
7L
8K
6L
7K
5L
6K
4L
3L
5K
4K
3K
0.25 0.26 0.27 0.28 0.29 0.30 0.31 0.32 0.33 0.34 0.35 0.36 0.37
Cx
3K
3L
4K
4L
Cx
0.273
0.266
0.280
0.286
0.266
0.258
0.273
0.280
0.286
0.280
0.291
0.296
0.280
0.273
0.285
0.291
Cy
0.227
0.232
0.252
0.244
0.232
0.239
0.261
0.252
0.244
0.252
0.268
0.259
0.252
0.261
0.279
0.268
5K
5L
6K
6L
Cx
0.296
0.291
0.310
0.313
0.291
0.285
0.307
0.310
0.313
0.310
0.330
0.330
0.310
0.307
0.330
0.330
2
Cy
0.259
0.268
0.297
0.284
0.268
0.279
0.312
0.297
0.284
0.297
0.330
0.310
0.297
0.312
0.347
0.330
7K
7L
8K
8L
Cx
0.330
0.330
0.338
0.352
0.330
0.330
0.347
0.345
0.352
0.338
0.364
0.360
0.345
0.347
0.367
0.364
Cy
0.310
0.330
0.342
0.344
0.330
0.347
0.371
0.352
0.344
0.342
0.380
0.357
0.352
0.371
0.401
0.380
2007-10-01
TLWD1100(T11)
Note 3: Iv rank classification
Test conditions: IF=20mA, Ta=25°C
Product name
Luminous intensity IV
min
typ
max
63
180
320
QA
63
⎯
125
RA
100
⎯
200
SA
160
⎯
320
TLWD1100(T11)
Unit
mcd
IF
20
mA
The specification on the above table is used for Iv classification of LEDs in Toshiba facility.
Each reel includes the same rank LEDs. Let the delivery ratio of each rank be unquestioned.
Note 4: Caution
ESD withstand voltage according to MIL STD 883D, Method 3015.7 : ≥1000V
When handling this LED, take the following measures to prevent the LED from being damaged or otherwise
adversely affected.
1) Use a conductive tablemat and conductive floor mat, and ground the workbench and floor.
2) Operators handling laser diodes must be grounded via a high resistance (about 1MΩ). A conductive strap is
good for this purpose.
3) Ground all tools including soldering irons.
This product is designed as a general display light source usage, and it has applied the measurement standard
that matched with the sensitivity of human's eyes. Therefore, it is not intended for usage of functional application
(ex. Light source for sensor, optical communication and etc) except general display light source.
3
2007-10-01
TLWD1100(T11)
TLWD1100
IF – V F
IV/IV(20 mA) – IF
(typ.)
(typ.)
3
100
IV/IV(20 mA)
(mA)
Ta = 25°C
Luminous intensity
Forward Current
IF
30
10
3
1
2.2
2.6
3.0
3.4
3.8
Forward Voltage
4.2
VF
4.6
Ta = 25°C
1
0.3
0.1
0.03
0.01
1
5.0
3
5
10
30
Forward Current
(V)
Relative IV – Tc
100
300 500
IF
(mA)
Cx, Cy – IF
(typ.)
10
50
(typ.)
0.34
Relative luminous Intensity IV
Ta = 25°C
Chromaticity Cx, Cy
0.33
1
Cx
0.32
0.31
Cy
0.3
0.1
0.29
-40
-20
0
20
40
Case Temperature
60
Tc
80
100
0
(°C)
0°
10°
20°
40°
30°
40°
50°
50°
60°
60°
70°
70°
80°
90°
20
25
30
IF
(mA)
Wavelength characteristic
Relative luminous Intensity
10°
15
35
40
(typ.)
1.0
Ta = 25°C
(typ.)
20°
10
Forward current
Radiation pattern
30°
5
0.8
0.6
0.4
0.2
80°
0
0.2
0.4
0.6
0.8
0.0
300
90°
1.0
400
500
Wavelength
4
600
700
800
λ (nm)
2007-10-01
TLWD1100(T11)
Packaging
These LED devices are packed in an aluminum envelope with a silica gel and a moisture indicator to avoid
moisture absorption. The optical characteristics of the devices may be affected by exposure to moisture in the air
before soldering and they should therefore be stored under the following conditions:
1. This moisture proof bag may be stored unopened within 12 months at the following conditions.
Temperature: 5°C~30°C
Humidity: 90% (max)
2. After opening the moisture proof bag, the devices should be assembled within 168 hours in an environment of
5°C to 30°C/60% RH or below.
3. If upon opening, the moisture indicator card shows humidity 30% or above (Color of indication changes to
pink) or the expiration date has passed, the devices should be baked in taping with reel.
After baking, use the baked devices within 72 hours, but perform baking only once.
Baking conditions: 60±5°C, for 12 to 24 hours.
Expiration date: 12 months from sealing date, which is imprinted on the same side as this label affixed.
4. Repeated baking can cause the peeling strength of the taping to change, then leads to trouble in mounting.
Furthermore, prevent the devices from being destructed against static electricity for baking of it.
5. If the packing material of laminate would be broken, the hermeticity would deteriorate. Therefore, do not
throw or drop the packed devices.
Mounting Method
Soldering
•
Reflow soldering
Temperature profile (example)
10 s max (*)
Package surface
temperature (°C)
240°C max(*)
140~160°C max (*)
(*)
4°C/s max
4°C/s max(*)
60~120 s max (*)
Time
•
•
•
•
•
(s)
The product is evaluated using above reflow soldering conditions. No additional test is performed exceed the
condition (i.e. the condition more than (*)MAX values) as a evaluation. Please perform reflow soldering under
the above conditions.
Please perform the first reflow soldering with reference to the above temperature profile and within 168 h of
opening the package.
Second reflow soldering
In case of second reflow soldering should be performed within 168 h of the first reflow under the above
conditions.
Storage conditions before the second reflow soldering: 30°C, 60% RH (max)
Make any necessary soldering corrections manually.
(only once at each soldering point)
Soldering iron
: 25 W
Temperature
: 300°C or less
Time
: within 3 s
If the product needs to be performed by other soldering method (ex. wave soldering), please contact Toshiba
sales representative.
Recommended soldering pattern
1.65
1.15
Unit: mm
1.65
2.41
5
2007-10-01
TLWD1100(T11)
Cleaning
When cleaning is required after soldering, Toshiba recommends the following cleaning solvents.
It is confirmed that these solvents have no effect on semiconductor devices in our dipping test (under the
recommended conditions). In selecting the one for your actual usage, please perform sufficient review
on washing condition, using condition and etc.
ASAHI CLEAN AK-225AES
KAO CLEAN TROUGH 750H
PINE ALPHA ST-100S
TOSHIBA TECHNOCARE
(FRW-17, FRW-1, FRV-100)
: (made by ASAHI GLASS)
: (made by KAO)
: (made by ARAKAWA CHEMICAL)
: (made by GE TOSHIBA SILICONES)
Precautions when Mounting
Do not apply force to the plastic part of the LED under high-temperature conditions.
To avoid damaging the LED plastic, do not apply friction using a hard material.
When installing the PCB in a product, ensure that the device does not come into contact with other cmponents.
Tape Specifications
1. Product number format
The type of package used for shipment is denoted by a symbol suffix after the product number. The
method of classification is as below. (this method, however does not apply to products whose electrical
characteristics differ from standard Toshiba specifications)
(1) Tape Type: T11 (4-mm pitch)
(2) Example
TLWD1100
(T11)
Tape type
Toshiba product No.
2.
Tape dimensions
Unit: mm
Symbol
Dimension
Tolerance
Symbol
Dimension
Tolerance
D
1.5
+0.1/−0
P2
2.0
±0.05
E
1.75
±0.1
W
8.0
±0.3
P0
4.0
±0.1
P
4.0
±0.1
t
0.3
±0.05
A0
2.9
±0.1
F
3.5
±0.05
B0
3.7
±0.1
D1
1.5
±0.1
K0
2.3
±0.1
K0
P0
D
t
P2
E
F
W
B0
P
D1
Polarity
A0
6
2007-10-01
TLWD1100(T11)
3. Reel dimensions
Unit: mm
9 ± 0.3
φ60
2 ± 0.5
φ13
φ44
+0
180 −4
11.4 ± 1.0
4. Leader and trailer sections of tape
40 mm or more
40 mm or more
(Note 1)
(Note 2)
Leading part: 190 mm (min)
Note1: Empty trailer section
Note2: Empty leader section
7
2007-10-01
TLWD1100(T11)
5. Packing display
(1) Packing quantity
Reel
2,000 pcs
Carton
10,000 pcs
(2) Packing form: Each reel is sealed in an aluminum pack with silica gel.
6. Label format
(1) Example: TLWD1100 (T11)
P/N:
TOSHIBA
TYPE
TLWD1100
ADDC
(T11)
Q’TY
Lot Number
Key code for TSB
(RANK SYMBOL)
32C
2,000 pcs
2000
Use under 5-30degC/6-%RH within 168h
SEAL DATE:
DIFFUSED IN *****
ASSEMBLED IN *****
[[G]]/RoHS COMPATIBLE
*Y3804xxxxxxxxxxxxxxxxx*
(2) Label location
• Reel
• Carton
Tape feel direction
Label position
Label position
• The aluminum package in which the reel is supplied also has the label attached to
center of one side.
8
2007-10-01
TLWD1100(T11)
RESTRICTIONS ON PRODUCT USE
20070701-EN GENERAL
• The information contained herein is subject to change without notice.
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his
document shall be made at the customer’s own risk.
• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which
may result from its use. No license is granted by implication or otherwise under any patents or other rights of
TOSHIBA or the third parties.
• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.
9
2007-10-01